Slideshare Engineering Graphics

ENGINEERING GRAPHICS
Dimension methods -
Diagonal Scale & Plane Scale
12/16/16 Prepared By Soham Kansodaria

DEFINITION
Dimensioning is the process of specifying part’ s
information by using of figures, symbols and notes.

a
10 27
43
13
123o
10 Drill, 2
Holes
R16
DIMENSION LINES
indicate the direction and extent of a dimension, and inscribe dimension figures.

Dimension lines should not be spaced too close
to each other and to the view.
11
34
Leave a space at least
2 times of a letter height.
16
35
DIMENSION LINES
Leave a space at least1
time of a letter height.

DIMENSION FIGURES
The height of figures is suggested to be 2.5~3 mm.
Place the numbers at about 1 mm above dimension
line and between extension lines.
COMMON MISTAKE
11
11
34
34

16.2516.25
or
DIMENSION FIGURES
When there is not enough space for figure or
arrows, put it outside either of the extension lines.
1
Not enough space
for figures
Not enough space
for arrows
1 1

Types of Lines Appearance
Name according
to application
Continuous thick line Visible line
Continuous thin line Dimension line
Extension line
Leader line
Dash thick line Hidden line
Chain thin line Center line

30
30
30
30
30
30
30
30
EXAMPLE : Dimension of length using aligned method.

45
o
45
o
45o
45o
45o
45o
45o
45o
EXAMPLE : Dimension of angle using aligned method.

30
30
30
30
3030
30
30
EXAMPLE : Dimension of length using unidirectional method.

45o
45o
45o
45o
45o
45o
45o
45o
EXAMPLE : Dimension of angle using unidirectional method.

FOR FULL SIZE SCALE
R.F.=1 OR ( 1:1 )
MEANS DRAWING
& OBJECT ARE OF
SAME SIZE.
Other RFs are described
as
1:10, 1:100,
1:1000, 1:1,00,000
DIMENSIONS OF LARGE OBJECTS MUST BE REDUCED TO ACCOMMODATE
ON STANDARD SIZE DRAWING SHEET.THIS REDUCTION CREATES A SCALE
OF THAT REDUCTION RATIO, WHICH IS GENERALLY A FRACTION..
SUCH A SCALE IS CALLED REDUCING SCALE
AND
THAT RATIO IS CALLED REPRESENTATIVE FACTOR.
SIMILARLY IN CASE OF TINY OBJECTS DIMENSIONS MUST BE INCREASED
FOR ABOVE PURPOSE. HENCE THIS SCALE IS CALLED ENLARGING SCALE.
HERE THE RATIO CALLED REPRESENTATIVE FACTOR IS MORE THAN UNITY.
REPRESENTATIVE FACTOR (R.F.) =
=
USE FOLLOWING FORMULAS FOR THE CALCULATIONS IN THIS TOPIC.
LENGTH OF OBJECT IN DRAWING
ACTUAL LENGTH OF OBJECT
LENGTH OF DRAWING
ACTUAL LENGTH
LENGTH OF SCALE = R.F. xx MAX. LENGTH TO BE MEASURED.

00 11 22 33 44 551010
PLAIN SCALE:-This type of scale represents two units or a unit and it’s sub-division.
METERSMETERS
DECIMETERSDECIMETERS
R.F. = 1/100R.F. = 1/100
4 M 6 DM4 M 6 DM
PLANE SCALE SHOWING METERS AND DECIMETERS.PLANE SCALE SHOWING METERS AND DECIMETERS.
PROBLEM NO.1:- Draw a scale 1 cm = 1m to read decimeters, to measure maximum distance of 6 m.
Show on it a distance of 4 m and 6 dm.
CONSTRUCTION:-
a) Calculate R.F.=
R.F.= 1cm/ 1m = 1/100
Length of scale = R.F. X max. distance
= 1/100 X 600 cm
= 6 cm
b) Draw a line 6 cm long and divide it in 6 equal parts. Each part will represent larger division unit.
c) Sub divide the first part which will represent second unit or fraction of first unit.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a look of scale.
e) After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance 4 m 6 dm on it as shown.
DIMENSION OF DRAWING
DIMENSION OF OBJECT

PROBLEM NO.2:- In a map a 36 km distance is shown by a line 45 cms long. Calculate the R.F. and construct
a plain scale to read kilometers and hectometers, for max. 12 km. Show a distance of 8.3 km on it.
CONSTRUCTION:-
a) Calculate R.F.
R.F.= 45 cm/ 36 km = 45/ 36 . 1000 . 100 = 1/ 80,000
Length of scale = R.F. max. distance
= 1/ 80000 12 km
= 15 cm
b) Draw a line 15 cm long and divide it in 12 equal parts. Each part will represent larger division unit.
c) Sub divide the first part which will represent second unit or fraction of first unit.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a look of scale.
e) After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance 8.3 km on it as shown.
KILOMETERSKILOMETERS
HECTOMETERSHECTOMETERS
8KM 3HM8KM 3HM
R.F. = 1/80,000R.F. = 1/80,000
PLANE SCALE SHOWING KILOMETERS AND HECTOMETERSPLANE SCALE SHOWING KILOMETERS AND HECTOMETERS
00 11 22 33 44 55 66 77 88 99 1010 11111010 55

11
22
33
44
55
66
77
88
99
1010
1’1’
2’2’
3’3’
4’4’
5’5’
6’6’
7’7’
8’8’
9’9’
10’10’
XX YY
ZZ
The principle of construction of a diagonal scale is as follows.
Let the XY in figure be a subunit.
From Y draw a perpendicular YZ to a suitable height.
Join XZ. Divide YZ in to 10 equal parts.
Draw parallel lines to XY from all these divisions
and number them as shown.
From geometry we know that similar triangles have
their like sides proportional.
Consider two similar triangles XYZ and 7’ 7Z,
we have 7Z / YZ = 7’7 / XY (each part being one unit)
Means 7’ 7 = 7 / 10. x X Y = 0.7 XY
:.
Similarly
1’ – 1 = 0.1 XY
2’ – 2 = 0.2 XY
Thus, it is very clear that, the sides of small triangles,
which are parallel to divided lines, become progressively
shorter in length by 0.1 XY.
The diagonal scales give us three successive dimensions
that is a unit, a subunit and a subdivision of a subunit.

R.F. = 1 / 40,00,000
DIAGONAL SCALE SHOWING KILOMETERS.
0 100 200 300 400 500100 50
10
9
8
7
6
5
4
3
2
1
0
KM
KM
KM
569 km
459 km
336 km
222 km
PROBLEM NO. 4 : The distance between Delhi and Agra is 200 km.
In a railway map it is represented by a line 5 cm long. Find it’s R.F.
Draw a diagonal scale to show single km. And maximum 600 km.
Indicate on it following distances. 1) 222 km 2) 336 km 3) 459 km 4) 569 km
SOLUTION STEPS: RF = 5 cm / 200 km = 1 / 40, 00, 000
Length of scale = 1 / 40, 00, 000 X 600 X 105
= 15 cm
Draw a line 15 cm long. It will represent 600 km . Divide it in six equal parts.( each will represent 100 km.)
Divide first division in ten equal parts . Each will represent 10 km . Draw a line upward from left end and
mark 10 parts on it of any distance. Name those parts 0 to 10 as shown . Join 9th
sub-division of horizontal scale
with 10th
division of the vertical divisions. Then draw parallel lines to this line from remaining sub divisions and
complete diagonal scale.

10
9
8
7
6
5
4
3
2
1
0
M
MM
CM
R.F. = 1 / 2.5
DIAGONAL SCALE SHOWING CENTIMETERS.
0 5 10 155 4 3 2 1
PROBLEM NO.6:. Draw a diagonal scale of R.F. 1: 2.5, showing centimeters
and millimeters and long enough to measure up to 20 centimeters. Show the distance 13.4 cm on it
SOLUTION STEPS:
R.F. = 1 / 2.5
Length of scale = 1 / 2.5 X 20 cm.
= 8 cm.
1.Draw a line 8 cm long and divide it in to 4 equal parts.
(Each part will represent a length of 5 cm.)
2.Divide the first part into 5 equal divisions.
(Each will show 1 cm.)
3.At the left hand end of the line, draw a vertical line and
on it step-off 10 equal divisions of any length.
4.Complete the scale as explained in previous problems.
Show the distance 13.4 cm on it.
13 .4 CM

Slideshare Engineering Graphics

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to Slideshare Engineering Graphics (20)

Recently uploaded (20)

Slideshare Engineering Graphics