Tekaba Manual

TTeekkaabbaa
Installation & Configuration Guide
Version 1.0

TTeekkaabbaa Version 1.0 - Installation & Configuration Guide
© 2014-2016 KaplanSoft - http://www.kaplansoft.com/ 2
Document Revision 1.0
http://www.kaplansoft.com/
Tekaba is built by Yasin KAPLAN
Read “Readme.txt” for last minute changes and updates which can be found under
application directory.
Copyright © 2014-2016 KaplanSoft. All Rights Reserved. This document is supplied by KaplanSoft.
No part of this document may be reproduced, republished or retransmitted in any form or by any
means whatsoever, whether electronically or mechanically, including, but not limited to, by way of
photocopying, recording, information recording or through retrieval systems, without the written
permission of KaplanSoft. If you would like permission to use any of this material, please contact
KaplanSoft.
KaplanSoft reserves the right to revise this document and make changes at any time without prior
notice. Specifications contained in this document are subject to change without notice. Please send
your comments by email to info@kaplansoft.com.
KaplanSoft is registered trademark of Kaplan Bilisim Teknolojileri Yazılım ve Ticaret Ltd.
Microsoft, Win32, Windows 2000, Windows, Windows NT and Windows Vista are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Table of Contents
Table of Contents.............................................................................................................................3
Introduction......................................................................................................................................4
System Requirements.......................................................................................................................4
Installation........................................................................................................................................4
Configuration ...................................................................................................................................4
Settings Tab..................................................................................................................................4
Adding Ports ....................................................................................................................................6
Telephony Routes ............................................................................................................................6
Service Monitor................................................................................................................................7

Introduction
Tekaba is a SIP media gateway (Based on RFC 3261) runs under Windows (Vista/7/8,
2003/2008/2012 Server). Visit http://www.kaplansoft.com/tekphone/ regularly for updates.
Major features:
 Simple, easy to use interface.
 Real time monitoring of active calls.
 Forwards incoming SMS as a SIP MESSAGE request.
 Accepts SIP MESSAGE requests and sends message content as SMS.
 Source IP address, source prefix, destination prefix based telephony routing.
 Supports G.711 A - Mu law codecs.
 Supports NAT traversal. Tekaba also supports UPnP.
 Supports call transfers by using SIP REFER method (RFC 3515)
 Supports, UDP, TCP and TLS transports with RTP and SRTP.
You need to add necessary mappings to your router for incoming RTP traffic if Tekaba installed
behind a NAT gateway which does not support UPnP.
System Requirements
Tekaba requires Microsoft .NET Framework 4.0 installed with the latest patches. Pentium i3 class
CPU with 2048 MB of RAM is ideal for most configurations. A 3G USB Modem with Huawei chip
which supports audio required. Freeware edition supports maximum one call at a time.
Installation
Unzip “Tekaba.zip” and click “Setup.exe” comes with the distribution. Follow the instruction of
setup wizard. Setup will install Tekaba, add a shortcut for Tekaba to desktop and the start menu.
Configuration
Run Tekaba Manager from Start Menu / Program Files / Tekaba.
Tekaba also checks if it is installed behind an UPnP supported NAT gateway. Tekaba also adds a
reverse mapping for incoming UDP connections automatically (Default UDP port 5080).
Settings Tab
Click Settings Tab to start configuration.

Figure - 1. Tekaba Gateway Settings
Enter following information in Gateway tab:
 Listen Port: You can define a port number to be listened (Default 5090).
 Use External Address: If TekPhone is installed behind a NAT gateway which does not
UPnP you can set external IP address manually for NAT traversal. If your NAT gateway
supports UPnP set UPnP Update Period to value greater than “0”.
 Logging: Select logging level of Tekaba. Select “None” if you do not want logging, select
“Errors” to log errors and select “Sessions” to log session information and errors. Log files
are located under <Application Directory>Logs directory.
 UPnP Update Period: You can specify period of querying UPnP Internet Access Gateway.
Set “0” to disable UPnP support.
Enter following information in SIP Proxy tab:
 SIP Domain: Enter a FQDN or an IP address of your SIP domain. You have to configure a
valid SIP domain for proper operation.
 SIP Proxy: Enter a FQDN of your SIP domain. Please make sure that this address is
resolvable by your SIP client and has a valid entry (an A record) in your DNS server if you
enter a FQDN. You have to configure a valid SIP proxy for proper operation.
 Register: SIP endpoint registration is disabled by default. If this option is enabled
TekPhone tries to register itself to configured SIP Domain.
 Account ID: You must specify a SIP endpoint ID for TekPhone. This ID is used by
TekPhone while registering to SIP registrar.
 Password: If SIP registrar requires password authentication specify password.
 Registration Timeout: You can specify registration timeout in seconds. Default is 600
seconds.

Figure - 2. Tekaba Sip Proxy Settings
If you click [Save] button setting will be saved and activated immediately. You can click “Register”
to SIP registrar/proxy manually.
Adding Ports
You need to have at least one 3G USB modem with audio support for the operation. You can plug a
USB modem either before or after starting Tekaba. Tekaba will recognize the modem and display
status of the modem in Ports tab. You can double click on modem enter to enter PIN If PIN entry
needed. You need to assign a trunk number first. It is 1 as default. You also need to specify a VoIP
route to forward incoming calls to a SIP endpoint. You just need to enter SIP endpoint Id or phone
number of the endpoint. You can do these settings by right clicking on the modem entry. Finally
you must enable the port for the operation.
Telephony Routes
You can specify telephony routes for VoIP to telephony destinations. Tekaba will select best
matching route to forward a VoIP call or SIP MESSAGE requests as SMS to a telephony
destination. You can specify Source IP Address, Source phone number (Prefix) and Destination
phone number (Prefix) and destination trunk. Tekaba will not route VoIP calls and SIP MESSAGE
requests as SMS if you do not specify telephony routes. You must enter a specific IP address as
Source IP Address; subnet based source IP address definition is not supported. You can enter * to
allow all values in Source IP Address, Source Prefix and Destination Prefix parameters.

Figure - 3. Tekaba Telephony Routes
Service Monitor
You can monitor active calls and port status through service monitor tab. You can clear log entries
by right clicking on Event Log list.
Figure - 4. Service Monitor Tab

Tekaba Manual

More Related Content

What's hot (20)

Viewers also liked (12)

Similar to Tekaba Manual (12)

More from Yasin KAPLAN (19)

Recently uploaded (20)

Tekaba Manual