Torbal platform balance

BA Platform and Remote Mount

Instruction Manual Model:
BA30 - BA303
BA30C - BA303C
BA30E – BA150E
BA3M – BA15M
BA3U – BA15U
BA15W

Table of Contents
Cautionary notes and precaution…...………………………………………………………………........................................... 2
1.1 Important handling cautions and warnings………………………………………………………………………………… 3
2. Specifications….…………………………………………………………………..……………………………………………. 5
3. Keys, Display Indicators and Abbreviations…….……………………………………………………………………………… 6
4. Parts Descriptions……………………………….....…………………………………………………………………………… 7
5. Unpacking Balance and Getting Started…….………………………………………………………….……………………… 8
10
6. Basic Principles of weighing………………….………………………………………………………..…………………………
7. Functions, Descriptions and Definitions…………..…………………………………………………..…………………………11
8. Weighing……………………..……………….……………………………………………………………………..……………12
8.1. Weighing…………………………………………………………………………………………………………….………12
8.2. Taring……………………………………………………………………………………………….……………………… 12
8.3. Extending the Resolution………………..………………………………………………………..…………………………14
8.4. Zeroing the Scale…………………………………………………………………………….........…………………………14
9. Auto-Zero………………….………………..……………………………………………………….…..……………………… 15
10. Parts Counting……………………………..……………………………………………………….….…………………………16
10.1. Using the Default Sample Setting…………………………………………………………..……………………………… 16
10.2. Using a custom sample size……………..……………………………………………………….………………………… 18
10.3. Counting based on a known Individual Piece Weight……….………………………………. …………….……………… 20
11. Units of Measure………………………………………………………………………………………………………………. 22
12. Percent Weighing…………………………………………………………………………………………………………………23
13. Recipe Weighing…………………..……………………………………………………………………..…………………….. 25
14. Calibration…………………………………………………………………………………………………….………………… 28
14.1. Quick Calibration…………………………………………………………………………………………………………. 28
14.2. Stepped Calibration………………………………………………………………………………………………………… 29
14.3. Calibrating with a calibration mass value which is not equal to the scale’s capacity……………………………………… 30
15. Port 1 - RS232 Communication Port Configuration………………………………………………………………………….… 32
15.1. Data Transmission and Exchange Protocol………………………………………….………………………………………32
15.2. Baud Rate……………………………………………………………………………………………..…………………… 34
15.3. Bites………………………………………………………………………………………………………………………… 34
15.4. Parity……………………..…………………………………………………………………………..……...………………35
16. Receipt Printout……………………………….………………………………………………………………………………… 36
16.1. Enabling and Disabling Receipt Field…………….…………………………………………………………………………37
16.2. Assigning Operator and Product ID numbers………..……….…………………………………………………………… 37
17. Dynamic and Animal Weighing LOC………………………………………………………………………………………….. 38
18. Storing Tare Values……….……………………………………………………………………………………………………. 39
18.1. Storing a Tare Value Manually………….………………………………………………………........................................ 39
40
18.2. Storing a Tare Value Automatically………...……………………………………………………..…………………………
18.3. Recalling a previously stored tare value…………………………..…………………………………………………………41
19. Min Max Weighing…………..………………………………………………………………………………………………… 42
20. Newton – Force Measurement………….…………………………………………………………………………..…………… 43
21. Filtering…………………..……………..……………………………………………………………………………………… 44
22. Date and Time……………………………………………………………………………………………………………….……45
45
22.1. Enabling and Disabling Date and Time stamping……………………………………………………………………………
22.2. Setting the current date and time…………………………………………………………………………………………… 45
22.3. Enabling PIN access to the Date Configuration Function…….………………….………………………………………… 47
48
23. Threshold Check Weighing and Opto-Isolator……………………………………………………………………………………
23.1. Enabling Check Weighing and Setting Threshold Limits………..………………………………………………………… 48
23.2. Setting the Output Mode for the Opto-Isolator………..….…………………………………………………………………50
23.3. Opto-Isolator Output…………………………………………………………………………………………………………51
24. Totalizing……………………….………………………….…………………………………………………………………… 52
24.1. Performing Totalizing……..…………………………………………………………………………………………………52
25. Changing to Grams (g) or Pounds (lbs)…………………..………..………………………………………………………….… 54
26. Menu Customization…………………………………………….……………………………………………………………… 55
27. Restoring Default Settings…………………………………….………………………………………………………………… 55
56
28. Common Errors and Troubleshooting…………………………………………………………………………………….………
29. Maintenance………………………………………………………………………………………………………….………… 56
30. Limited Warranty…………………..………………………………………………………………..………..………………… 57

1.

Torbal Platform Balances

Chapter 1: Cautionary Notes
Remember choose a proper location for you scale and to always handle the unit with care.
The correct location and proper environment makes an important contribution to the accuracy of the weighing
results of TORBAL industrial scales.
The optimum location for your scale:

•
•
•
•
•

Stable, vibration-free base as horizontal as possible
Away from direct sunlight
Not exposed to high temperature variations
Away from direct drafts
The best location is a stable surface away from direct drafts, doors, windows, radiators and air
conditioner vents.

-2-

CAUTION:

•
•
•
•
•
•
•
•

WARNING:

•
•
•
•

1.1.

The scale is designed for indoor use only.
Do not operate the scale in hazardous areas or conditions.
Do not use the scale in locations subject to high humidity.
Do not connect cables in ways other than those mentioned in this manual.
Be sure to set the scale on a firm, stable, horizontal surface.
Never stand on or lean on this product. Equipment may fall or collapse, causing breakage
and possible injury.
Before moving the product, unplug it and unplug all cables connected to it.
When storing, transporting or returning the scale for service, always use the original
packaging.
Never attempt to repair, disassemble or modify the scale yourself. Tampering with the scale
may result in injury and cause more damage to the equipment.
Be sure to use the specified power source.
Do not allow foreign matter to fall into the scale.
If water or other liquid spills into the scale, do not continue to use it. Unplug the power cord
immediately and contact technical support.

Important handling Cautions and Warnings
Always handle your scale with care. Damage caused by improper handling is not covered under the
scale’s warranty.

Never drop or throw any articles onto the scale’s
pan or onto any other parts of the unit!

DO NOT let the scale fall or drop from its
tabletop surface!

DO NOT pass or handle liquids directly over the
scale to avoid spillage and liquid damage!
-3-

Follow all safety guidelines in order to avoid electrical shock, or damage to
connected peripheral devices.

•

All necessary repairs or internal adjustments should be made by authorized personnel only.

•

To avoid the risk of fire use an outlet of the proper type that provides the specified voltage. The
required voltage for the power supply is 115vAC @ 60Hz and requires a minimum of 1.2 amperes
of current.

•

Do not use the scale when the cover is open.

•

Do not use the scale in explosive atmospheres.

•

Do not use the scale in very high humidity.

•

If the scale does not operate properly, unplug the power supply and do not use it until checked by
authorized personnel.

Disposal of electronic equipment in waste containers is
forbidden by law.

•

Please dispose of electronic equipment in appropriate recycling centers or by
returning to the original point of purchase.

-4-

Chapter 2: Specifications
Table 1. Economy Series and Remote Mount Series
Specification
Capacity Kg/lb
Readability (d) g/lb
Increased Resolution
(5sec) g/lb
Stabilization time
Tare Range in Kg
Platform Dimensions
mm (in)
Indicator Dimensions
mm (in)
Overall Height or
Dimensions mm (in)
Scale Weight
Operating Temp
Power Supply
RS-232 Port
Opto-Isolator
Class
Warranty

30C

60C

153C

30/60
10/0.02
1/0.002

60/150
20/0.05
2/0.005

150/300
50/0.1
5/0.01

-30

-60
400x500
(15.8x19.7)
400x620x125
(15.8x24.4x4.9)

< 4 sec
-150

Model Number - BA
303C
30E
60E
300/600
100/0.2
10/0.02

30/60
10/0.02
1/0.002

-300

-30

500x600
(19.7x23.6)
500x730x150
(19.7x28.7x5.9)
860 (33.9)

60/150
20/0.05
2/0.005

150E

3U

6U

15U

150/300
50/0.1
5/0.01

3/6
1/0.002
0.1

6/15
2/0.005
0.2

15/30
5/0.01
0.5

< 4 sec
-60
-150
400x490x130
(15.8x19.3x5.1)

400 x 655 x 725
(15.8 x 25.8 x 28.5)
15Kg/33 lb
-10C to 40C
12 VDC@500ma
Bidirectional
Yes
III
One year

12Kg/26.4 lb

25Kg/55. lb
-10C to 40C
12.VDC@850ma
Bidirectional

-3

< 4 sec
-6
-15
250x260x100
(9.8x10.2x4.3)
NA

3.5Kg/7.7 lb
-10C to 40C
12 VDC@600ma
Bidirectional

Table 2. Heavy Duty Series
Specification
Capacity Kg/lb
Readability (d) g/lb
Increased Resolution
(5sec) g/lb
Stabilization time
Tare Range Kg
Platform Dimensions
mm (in)
Overall Dimensions
mm (in)
Scale Weight Kg/lb
Operational Temp
Power Supply
RS-232 Port
Opto-Isolator
Class
Warranty

3M
3/6
1/0.002
0.1/
-3

6M
6/15
2/0.005
0.2

15M
15/30
5/0.01
0.5

< 3 sec
-6
-15
300 x 300 (11.8 x 11.8)
305 x 445 x 415
(12 x 17.5 x 16.3)
7 /15.4
12 VDC@160ma

Model Number - BA
15W
30
15/30
30/60
5/0.01
10/0.02
0.5
1/0.002

60
60/150
20/0.05
2/0.005

153
150/300
50/0.1
5/0.01

303
300/600
100/0.2
10/0.02

< 4sec
-30
-60
-150
-300
380x380x100
400 x 490 x 130
600 x 485 x 140
(15x15x3.9)
(15.8 x 19.3x5.1)
(23.6 x 19.1 x 5.5)
380x540x585
400 x 650 x 740
600 x 650 x 740
(15x21.3x23)
(15.8x25.6x29.1)
(23.6 x 25.6x29.1)
12/26.4
17/37.4
27/59.4
-10C to 40C
12 VDC @ 850ma
Bidirectional
Yes
III
One Year
-15

-5-

Chapter 3: Keys, Display Indicators and Abbreviations

Key

Primary Function
Power On and Power Off

T

Tare – used to tare the weighing pan

0

Zero – used to zero the scale (Legal for Trade models only)

MENU

Menu – used to access the main menu
Data Transfer – used to print data or transfer data to a PC via the RS232 communication port

B/G

Gross Weight – used to change display from Net Weight to Gross Weight

HR

High Resolution – temporarily (5 sec) increases the display resolution

Display Indicator

Description
Stability Indicator - The weighing result has stabilized and an accurate reading may be taken.
Zero - The scale is maintaining a “center of zero” condition. (Legal for Trade models only)

AUT

AZSM (Automatic Zero Setting Mechanism) is enabled. Always enabled in Legal for Trade models.

NET

Net Weight – indicates that the container weight has been removed by tare

-6-

Chapter 4: Parts Description
BA Models:

Front View

Rear View

Indicator

Pan Base

Pan

AC Adapter

RS232 and Output Port

Column

Level Indicator

-7-

AC Adapter Socket

Chapter 5: Unpacking the Balance and Getting Started
1. Carefully remove the scale, pan, and all of its components out of the packaging and place them on a
stable surface where the scale will not be affected by any mechanical vibrations or high air
movements.
2. After removing all components from the packaging refer to the assembly instructions which have been
provided with the scale, and carefully assemble the unit.

3. After assembling the scale lift the platform pan and then remove straps which are used to secure the
frame during shipping.
Important: When transporting the scale these straps must be replaced prior to shipping.

4. Use the rotational feet to level the scale. An air bubble level is built into the platform for this purpose.
Adjust the feet until the bubble is center in the level indicator. Lock the feet in position with the
locking nuts.

Correct

Incorrect

-8-

5. After leveling the scale, you may plug the AC adaptor to the AC adaptor socket located in the rear of
the scale.

6. When the AC adapter is
plugged into the wall outlet,
the scale will turn “ON”
automatically, initialize itself,
and enter weighing mode.

C-1

0.00

7. To turn the scale off press the Power “OFF” button (

-9-

).

Chapter 6: Basic Principles of Weighing
1. The scale should be properly zeroed before weighing. Proper zeroing is indicated by the Zero
Indicator (→0←) on the display. If the display signals an out of zero condition (----), press the
(→0←) key to Zero an empty pan.
2. Weighing allows taring over the entire weight range. This is accomplished by pressing the Tare
key, (→T←). Care should be exercised when tare is in use to be sure that the scale’s maximum
capacity is not overloaded.

3. An accurate weighing result should not be taken until the stability indicator, (
the result is stable.

) , indicates that

4. For best results place the unknown weight in the center of the pan.
5. Always protect the scale from dirt, dust, and corrosive liquids. When Cleaning use of a clean cloth
with soap and water, and then dry with a clean wiper.
6. Use the “Active” function to customize the scale’s main menu and disable functions that are not used.
This makes use the main menu fast and easy.

Never overload the scale in excess of 20% of the scale’s rated maximum
capacity.

- 10 -

Chapter 7: Functions, Descriptions and Definitions
•

Parts Counting is used to count parts based on their established average piece weight.

•

Percent weighing is used to establish the relative weight of an unknown, compared to that of a stored
reference weight and expressed as a percent.

•

Recipe Making is used for weighing and summing individual ingredients such as powers or liquids
during recipe making or mixing compounds.

•

Check weighing is used to check whether a weight of an object falls within specified threshold limits.

•

Animal and dynamic weighing is used to weigh animals or objects which are in motion while on the
pan.

•

Tare Storing is used to store the values of various containers used for weighing.

•

Filtering is used to minimize or eliminate the effects of vibrations in the weighing surface.

•

Min / Max Indication is used in conjunction with Check Weighing to control external indication or
sorting equipment.

•

Totalizing is used for summation of sequential weighing results of items or articles.

- 11 -

Chapter 8: Weighing
8.1. Weighing
1. To begin weighing, press the power button (
) to turn the scale ON. The scale will go through its
initialization procedure and automatically enter “Weighing Mode”. The scale is ready to begin
) and zero ( 0 ) indicators appears on the display.
weighing as soon as the stabilization (

0.00
2. When weighing, always place the mass in the middle of the pan. The weighed result may be taken
when the stabilization indicator appears on the display.

12.00
8.2.Taring
1. If a container is used for weighing, it may be tared. In taring the container, the scale subtracts the
weight of the container from the gross weight to obtain the net weight.
2. To tare the weighing container, place it in the middle of the pan. The container’s weight will be shown
on the display.

2.04

- 12 -

3. Once the stabilization indicator appears on the display, the container is ready to be tared. To tare the
container, press the “T” button. The display will show a dotted line which indicates the scale has
begun the taring process.

------4. When finished taring, the balance will return to weighing and the NET indicator will be lit. The
display will indicate 0.00g.

0.00
5. Place the unknown weight in the tared container. The NET weight will be displayed.

20.00
6. To obtain the gross weight (Tared container + unknown weight) press the B/G key.

22.04

- 13 -

8.3. Extending the resolution
1. The resolution of the scale can be temporarily increased by pressing the HR key. This temporary
increase in resolution can be very useful in scales where d=e. The display resolution is increased for 5
seconds and then reverts automatically.

22.036
Note: These results are not legal for trade and cannot be sent to a printer or an external computer.

8.4. Zeroing the scale
If the display signals are out of zero condition “--", the scale must be zeroed before weighing.

- 1. To zero the scales press the

0

key.

0.00

-------

- 14 -

Chapter 9: Auto-zero (AutotA)
All BA Scales are equipped with AZSM, the “Auto Zero Setting Mechanism.” AZSM automatically
maintains a center of zero and it is set to 0.5d/s.
1. Enter the main Menu by pressing the MENU key

0.00
.
2. Select “AutotA” by pressing the T key.

Autota
3. To enable Auto-zero press the T key when “Aut on” is displayed, to disable press the T key when
“AutoFF” is displayed or select “out” to exit.

Aut on

Autoff

- 15 -

Chapter 10: Parts Counting (PCS)
Functions Options:
PCS Off
( PCsoff)
PCS On
(pcs on)
PCS ..
(PCS . .)
PC Set
(PC SET)
PC UM
(PC UMM)
PCS RS
(PCs rS)

Disables Parts Counting
Enables Parts Counting
Recalls the last Average Pieces Weigh used in for counting
Setting a custom sample size
Setting a custom known Individual Piece Weight
obtaining the average piece weight from secondary higher accuracy scale via RS232

10.1. Using a default sample size setting
1. Place the counting container on the pan while in the weighing and press the T key to tare the
container.

------2. Place a sample in the container. The sample size must equal to one of the pre-set options:
5,10,20,50,100, 200,500, and press the MENU key

25.00
3. Wait for PCS to appear on the display and press the T key

pCS
- 16 -

4. Select “PCS on” by pressing the T key.

pCS on
5. Available sample size options will alternate on the display. Press the T key to select a size value
equal to the number of the sample placed in the container.

pCS

5

6. After the sample size has been selected, the scale will display the count of the sample. At any time
you can proceed with the count.

17
7. To turn parts counting off, select PCS from the main menu and press the T key when “PCSoFF” is
displayed.

- 17 -

10.2. Using a custom sample size
1. Place the counting container on the pan while in the weighing mode and press the T key to tare the
container.

------2. Place a desired sample size in the container and press the MENU key. (i.e. 12 as illustrated)

25.00
3. Wait for “PCS” to appear on the display and press the T key

pCS

pCS on
- 18 -

5. Available sample size options will alternate on the display. Press the T key when “PC Set” is
displayed.

pC

set

6. A dashed line will be displayed indicating to manually enter the value for your sample size in the
container. To do so, use the following keys: the 0 key to increment a digit, the T key to accept
and go to the next digit, and MENU to accept the entire setting.

To increment a digit

To accept and go to next digit

To accept entered value

.

12

7. Once your custom sample size value has been entered and the MENU key pressed, the scale will
display the count of the sample. At any time you can proceed with the count.

50
8. Once an accurate count has been taken, the container and its contents may be removed from the
scale. To Turn parts counting off, select “PCS” from the main menu and press the T key when
“PCSoFF” is displayed.
- 19 -

10.3. Counting based on a known Individual Piece Weight (No Sample Size Required)
1. Place the counting container on the pan and press the T key to tare the container.

------2. Press the MENU key to enter the main menu.

3. Wait for “PCS” to appear on the display and press the T key

pCS

pCS on
5. Available sample size options will alternate on the display. Press the T key when “PC uM” is
displayed.

pC

UMM
- 20 -

6. A dashed line will be displayed indicating to manually enter the exact individual piece weight of
the counted parts. To manually enter the individual piece weight, use the following keys: the C key
to increment a digit, the T key to accept and go to the next digit, the
key to insert a decimal,
and the MENU key to accept the entire setting.


To accept and go to
next digit

.

To insert a decimal

To accept entered
value

10.00

7. Once the individual piece weight is entered and the MENU key pressed, the scale will display
“0pcs”. At any time proceed with the count.

5
8. Once an accurate count has been taken, the container and its contents may be removed from the
scale. To exit parts counting and return to basic weighing, select “PCS OFF” from the parts
counting menu.

- 21 -

Chapter 11: Units of measure (Unit)
The BA Scales can operate in nine different units of measure: Grams (g), Kilograms (kg), Carats (ct), Pounds
(lb), Newton, Grains, Ounces, Ounces Troy, Pennyweight. By factory default, the scale is set to weigh in
grams (lb). To select a different unit of measure, follow the steps below.
1. Enter the main menu by pressing the MENU key.

2. When command “UNITS” is displayed, press the T key.

Unit
3. The scale will display available units of measure sequentially.

Carat

penny

4. When the desired unit is displayed, press the T key to make the selection.

5. Once the selection is made, the scale will automatically return to the weighing mode

- 22 -

Chapter 12: Percent Weighing (Perc)
Function Options:
PER Off
( Peroff)
PER On
(per on)

Disables Percent Weighing
Enables Percent Weighing

Percent weighing is used to express the weight of an object as a percentage of a stored sample weight. To use
percent weighing, follow these steps:
1. Place container on the pan and press the T key to tare.

------2. Once the scale has been tared, place the sample reference weight on the pan.

15.23
3. The weight of the sample will be displayed as it is placed on the pan. Once the weight of the
sample stabilizes and the stability indicator appears on the display, press the MENU key to
enter the main menu.
4. When “PERCENT” is displayed, press the T key.

PerC
- 23 -

5. Commands “PER OFF” and “PER ON” will be displayed sequentially. To proceed with percent weighing
and set the reference sample weight, press the T key when command “PER ON” is displayed.

Per

on

6. Once the reference sample weight is set, the scale will express the weight as a percentage.

100.0
7. Remove the sample and place an object in the container. The scale will express the weight of that object as
a percentage of the stored sample.

50.0
8. To exit percent weighing and return to basic weighing, select “PER OFF” from the percent menu.

- 24 -

Chapter 13: Recipe Weighing (Recipe)
Function Options:
Rec Off
( rECoff)
Rec On
(reC on)
Rec Con
(reCCon)

Disables Recipe Weighing
Enables Recipe Weighing
allows to continue recipe making after obtaining a total

1. Place the counting container on the pan and press the T key to tare the container.

------2. Press the MENU key to enter the main menu.

3. Wait for “RECIPE” to appear on the display and press the T key

reCIpe
4. Select “Rec on” by pressing the T key.

REC on

- 25 -

5. The display will read 0 indicating that you may place the first ingredient into the container. Once the
Weight of the ingredient stabilized press the T key to accept the ingredient weight.

0.22
6. Once the weight has been accepted place the second ingredient into the container. Once the weight of the
second ingredient stabilizes press the T key to accept the ingredient weight.

0.37
7. Steps 1 and 2 can be repeated until all ingredients are in the container. Before obtaining a Total make sure
that the last ingredient weight was accepted and the display reads 0.

0.44
8. To obtain the Total for the recipe press the Menu key, select the “Recipe” function, and then select “Rec
Off”

reCIpe

reCoff

- 26 -

9. The total of all ingredients will be displayed.

1.04
10. To continue Recipe making press the Menu select the “Recipe” function, and then select “Rec Con”

reCIpe

reCCon

11. Press the T key to accept the current Total and repeat steps 5 through 7 to add more ingredients.
12. To Clear and start a new recipe, remove the container and all ingredients from the pan and press the zero
key 0 . Once the result is cleared, repeat steps 1 through 9.

- 27 -

Chapter 14: Calibration (CaLIb)
Function Options:
CAL On ( CaL oN)
CAL Stp

(CALSTP)

Other

(other)

Starts Quick Calibration. Recommended when calibrating with a single calibration
weight.
Starts Stepped Calibration. Recommended when calibrating with multiple
calibration weights.
Calibration with calibration mass not equal to the scale’ capacity.

Calibration with an external Calibration Weight should be performed if the scale exhibits erroneous readings
or periodically to assure accuracy of all weighing results. The scale should be calibrated with a high accuracy
weight equal to its maximum capacity. Before starting calibration, have the appropriate calibration weight
available.
14.1 Quick Calibration (calibrating with a single calibration weight).
1. Press the MENU key, when the option “Calib” is displayed press the T key, and then select the option
“CAL On” by press the T key once again.

CAL oN

CaLIb

2. The scale will display a full a calibration mass equal to the scales capacity i.e.”30”, and an option to select
a different calibration mass”other“. To calibrate the scale with a mass value equal to the scales capacity
press the T key when the calibration mass value is displayed (proceed to step 4). To calibrate the scale
with a mass lower than the scale’s maximum capacity, press the T when “other” is displayed (proceed to
step 3).

30

other

3. If option “other” has been selected a dashed line will be displayed indicating to manually enter the exact
value of the calibration mass used to calibrate the scale. To manually enter the calibration value, use the
following keys: the C key to increment a digit, the T key to accept and go to the next digit, the
key to
insert a decimal, and the MENU key to accept the entire setting.


To accept and go to
next digit
- 28 -

To insert a decimal

To accept entered
value

4. The scale will perform a tare and the message “LOAD” will be displayed.

------

-CAL-

LOAD

5. When the message “LOAD” is displayed, place the calibration weight on the scale’s hanging pan.
Calibration will begin automatically and “WAIT” will be displayed indicating that calibration is in
progress.

wwAIT
6. When finished the scale will automatically return to the weighing mode, and the calibration weight can be
removed from the pan.

30.00

- 29 -

14.2 Stepped Calibration (calibrating with multiple calibration weights.)
1. Press the MENU key, when the option “Calib” is displayed press the T key, and then select the option
“CAL Stp” by press the T key once again.

CAL STP

CaLIb

2. The scale will display a full a calibration mass equal to the scales capacity i.e.”30”, and an option to select
a different calibration mass”other“. To calibrate the scale with a mass value equal to the scales capacity
press the T key when the calibration mass value is displayed (proceed to step 4). To calibrate the scale
with a mass lower than the scale’s maximum capacity, press the T when “other” is displayed (proceed to
step 3).

30

other

3. If option “other” has been selected a dashed line will be displayed indicating to manually enter the exact
value of the calibration mass used to calibrate the scale. To manually enter the calibration value, use the
key to


To accept and go to
next digit

To insert a decimal

To accept entered
value

4. The scale will display the message “Press Menu”. When you are ready to Tare the scale Press the MENU
key.

-CALpress

mmenu

- 30 -

5. The scale will perform a tare and the message “LOAD” will be displayed indicating to place all
calibration weights on the pan. After placing all weights on the pan, press the Menu key to initiate the
calibrations process.
Caution: Do not press Menu until all calibration weights are on the scale’s pan

------CALpress

LOAD
mmenu

6. Message “CCCCCC” will be displayed indicating that calibration is in progress. When finished the scale
will automatically return to the weighing mode and the calibration weights can be removed from the pan.

CCCCCC

30.00

- 31 -

Chapter 15: Port 1 - RS232 Communication Port Configuration (Port-1)
After a weighing transaction is completed, a result data receipt can be printed. To initiate printing, press the
data transfer key. Data may be sent to a printer or a PC via the Torbal Communication Software.
15.1. Data Transmission and Exchange Protocol
Data Transmission (LONG):
Transmission Parameters: 8 bits, 1 stop bit, no parity, baud rate 4800bps,
Exchange data:
, in weighing:
Transmit the weight (equivalent to the Print Key,
Computer→Scale: S I CR LF (53h 49h 0Dh 0Ah) – initiating signal,
Scale→Computer: scale sends 16 Bytes of data as follows:
Byte
Byte
Bytes
Bytes
Byte
Byte
Byte
Byte
Byte
Byte
Byte

1
2
3,4
5-9
10
11
12
13
14
15
16

-

The character ‘-‘ or space
space
digit or space
digit, comma, or space
digit
space
k, l, c, p or space (for kg,lb,ct,pc, or%)
g, b, t, c or %
space
CR
LF

‘Tare the weight’ (corresponds to the →T← key in weighing):
Computer→Scale: S T CR LF (53h 54h 0Dh 0Ah),
Scale→Computer: no response.
‘Zero the scale’ (corresponds to the key →0← in weighing):
Computer→Scale: S Z CR LF (53h 5Ah 0Dh 0Ah),
Scale→Computer: no reponse.
‘Turn On / Off the Scale (corresponds to the key I/ in weighing):
Computer→Scale: S S CR LF (53h 53h 0Dh 0Ah),
‘Display the MENU’ (corresponds to the key MENU in weighing):
Computer→Scale: S F CR LF (53h 46h 0Dh 0Ah),
Setting the threshold 1 (optional):
Computer→Scale: S L D1...DN CR LF (53h 4Ch D1...DN 0Dh 0Ah)
where: D1...DN – Threshold value, up to 8 characters,
- 32 -

Scale→Computer: no response,
Example:
To set 1000g in weight B1.5 (d=0.5g) type:
S L 1 0 0 0 . 0 CR LF (53h 4Ch 31h 30h 30h 30h 2Eh 30h 0Dh 0Ah).
To set 100kg in weight B150 (d=50g) type:
S L 1 0 0 . 0 0 CR LF (53h 4Ch 31h 30h 30h 2Eh 30h 30h 0Dh 0Ah),
Setting the threshold 2 (optional):
Computer→Scale: S H D1...DN CR LF (53h 48h D1...DN 0Dh 0Ah),
where: D1...DN – threshold value, up to 8 characters,
Scale→Computer: no response

Cable WK-1 Configuration

Cable WD-1 Configuration

- 33 -

15.2. Baud Rate
1. Press the Menu key, when the option “Port - 1” is displayed press the T key, and then select the option
“Baud” by press the T key once again.

Port -1

bAUd

2. The scale will begin to display available baud rates: “4800”, “9600”, “19200”, “38400”, and “57600”.
To make a selection, press the T key when the desired setting is displayed.

4800

9600

19200

38400

57600

15.3. Bites
1. Press the MENU key, when the option “Port - 1” is displayed press the T key, and then select the option
“Bites” by press the T key once again.

Port -1

bItES

2. The scale will display available Bits settings: “7-bit”,”8-bit”. To make a selection press the T key when
the desired setting is displayed.

7 - bIt

8 - bIt
- 34 -

15.4. Parity
1. Press the MENU key, when the option “Port - 1” is displayed press the T key, and then select the option
“Parity” by press the T key once again.

Port -1

PARITY

2. The scale will display available Parity settings: “none”, ”odd”, “even”. To make a selection press the T
key when the desired setting is displayed.

none

odd

- 35 -

evEN

Chapter 16: Receipt Printout (PrInt)
A detailed transaction receipt can be printed after weighing has been completed. The receipt can be
customized to include the following information:

Header

Header – includes unit information such as: Mode
number, Max Capacity, resolution and Unit Serial
number.

idOPER

Operator Id – shows the ID number of the user
which performed the weighing transaction

DATE

Date – Date of the performed transaction

TIME

Time – Time at which the transaction was performed

prn no

Printout number – Number of the receipt prenticed
in a given day

ID Prod

Product Id – ID number of the product or item
weighed

Count

Count – Result obtained in Parts Counting

ApWW
NETTo
tare
brUTTo
total

APW – Average Piece weight of the counted parts in
the Parts Counting Functions
Net – Net result of the weighing transaction
Tare – tared weight in the weighing transaction
Gross – gross weight of the weighing transaction
Total – grand total obtained in the totalizing function

- 36 -

16.1. Enabling and Disabling Receipt Fields
1. Press the MENU key, when the option “Print” is displayed press the T key, and then select a desired field
by press the T key once again when the name is displayed.

PrINT

HEADER

2. The scale will display options “ON” and” Off”. To enable the field press the T key when “On” displayed,
to disable the field press the T key when “Off” is displayed.

ON

OFF

16.2. Assigning Operator and Product ID numbers.
1. From the weighing mode press and hold the MENU key for 3 seconds or until the scales displays
“IDPROD” and “IOPER”. Select the desired option by pressing the T key.

0.00

IDPRoD

2. A dashed line will be displayed indicating to manually enter ID number. To manually enter the ID
number, use the following keys: the C key to increment a digit, the T key to accept and go to the next
digit, the
key to insert a decimal, and the MENU key to accept the entire setting.


To accept and go to
next digit

- 37 -

To insert a decimal

To accept entered
value

Chapter 17: Dynamic and Animal Weighing (LOC)
Function Options:
LOC Off ( LOC oFF)
LOC On (LOC on)
LOC Prn

(LOC Prn)

Disables the LOC Dynamic Weighing Function
Enables and Starts the LOC Dynamic Weighing Function (Weight integration
initiates automatically)
- Enables and Starts the LOC Dynamic Weighing Function (Weight integration is
initiated manually with the press of the Data Transfer Key
)

1. Place a container on the pan and press the T key to tare.

------2. Press the MENU key, when the option “LOC” is displayed press the T key, and then select the option
“LOC On” or “LOC Prn” by press the T key once again.

LOC

LOC oN

3. Place the animal or the moving object on the pan. Weight integration will begin automatically. If “LOC
Prn” was selected press the data transfer key to initiate weight integration manually
. While the scale
is integrating the weighing result the display flashes.

0.28
4. Final result will be automatically sent to a printer or a PC via the RS232 port. During data transmission
the word print will be displayed. The final result remains displayed for 30 seconds. To perform the next
weighing remove the animal, wait for the scale to display 0 and place the next animal on the pan.
- 38 -

Chapter 18: Storing Tare Values (Tare)
18.1. Storing a Tare Value Manually
1. Press the MENU key, when the option “Tare” is displayed press the T key, and then select the option “Tar
Set ” by press the T key once again.

tare

tarset

2. The scale will begin to display tare locations. Locations marked with a dot in the upper left corner of the
LED have a stored tare value assigned. To select a tare location or overwrite a current location press the T
key when a desired location is displayed, and then select the option “Manual ” by press the T key once
again.

tare 1

mmanual

3. A dashed line will be displayed indicating to manually enter the Tare value. To manually enter tare value,
use the following keys: the C key to increment a digit, the T key to accept and go to the next digit, the
key to insert a decimal, and the MENU key to accept the entire setting.


To accept and go to
next digit

To insert a decimal

To accept entered
value

4. Once a tare value has been assigned, the scale will automatically store the value in the selected memory
location and return to the weighing mode with the tare value in use.

- 39 -

18.2. Storing a Tare Value Automatically
1. Place a container on the pan and press the MENU key to enter the main menu.

0.60
2. When the option “Tare” is displayed press the T key, and then select the option “Tar Set” by pressing the
T key once again.

tare

tar set

LED have a stored tare value assigned. To select a tare location or overwrite a current location press the T
key when a desired location is displayed, and then select the option “Pan ” by press the T key once again.

tare 1

PAn

4. The scale will automatically store the value of the container on the in the selected memory location and
return to the weighing mode with the tare value in use.

- 40 -

18.3. Recalling a previously stored tare value.
1. Press the MENU key, when the option “Tare” is displayed press the T key, and then select the option “Tar
On ” by press the T key once again.

tare

tar on

LED have a stored tare value assigned. To select a tare location press the T key when a desired location is
displayed.

tare 1
3. The scale will return to the weighing mode with the selected tare value in use.

- 41 -

Chapter 19: Min – Max Weighing (Up)
This function allows you to find the maximum (highest) or minimum (lowest) weight in a series of weights.
1. Press the MENU key. When the option “Up” is displayed press the T key, and then select the option
“High” or “Low” by press the T key once again.

up off

HIGH

LOWW

2. The scale will return to weighing and it will begin to hold on the display the highest or the lowest weight.
When seeking the highest weight in a series make sure to remove the previous weight from the pan before
adding the new weight. When seeking the lowest value weight be sure to add the new weight before
removing the previous weight.
Note: Add and remove weights with care in order not to increase the weight unintentionally.

1.00

10.00

Note: Stability indicator and Auto-Zero is disabled during Min/Max weighing.

- 42 -

10.00

Chapter 20: Newton – Force Measurement (NewwtO)
This function changes the unit of weight to Newton (N) - 1N ≈0.101971 kg
1. Press the MENU key, when the option “Newton” is displayed press the T key.

newwtO
2. The scale will display options “ON” and” Off”. To enable Newton force measuring press the T key when
“New On” displayed, to disable Newton force measuring press the T key when “New Off” is displayed.

neww ON

nww oFF

- 43 -

Chapter 21: Filtering (FILter)
This function is used when vibration is encountered during weighing. This may be the result of ground
vibration, or a vibrating live load on the pan. Increasing the filter setting will increase the time required for a
measurement. The integration time of the measurement is increased thereby eliminating higher frequency
vibration.

1. Press the MENU key, when the option “Filter” is displayed press the T key.

fILTER

2. The scale will display options “Off” and available filter sensitivity levels “Fil 10, Fil 20, Fil 30 and Fil
40”. To select and enable Filtering press the T key when a desired filter level is displayed.
Filter

Sensitivity
Low
Medium
High
Severe

FIL 20

FIL 30

Fil 10
Fil 20
Fil 30
Fil 40

FIL 10

3. To disable filtering select “Fil Off” from the filter menu.

- 44 -

FIL 40

Chapter 22: Date and Time (DATE)
Function Options:
Dat On
(DAT oN)
Dat Off
(DAToff)
Dat Set
(datset)
Dat Pin
(datpIn)
Dat For
(datfor)

Enables date and time printing with every weighing result.
Disables date and time printing.
Date configuration” allows to set the current date and time.
Enables PIN access to the Date Configuration.
Format selection (United States / Europe).

22.1. Enabling and Disabling Date and Time stamping
1. Press the MENU key, when the option “Date” is displayed press the T key.

date

2. The scale will display options “Dat On, Dat Off, Dat Set, Dat Pin, Dat For” . To enable Date stamping
press the T key when “Dat On” is displayed, to disable press the T key when “Dat Off” is displayed.

dat ON

dat oFF

22.2. Setting the current date and time
1. Press the MENU key, when the option “Date” is displayed press the T key, and then select the option “Dat
Set ” by press the T key once again.

Date

DATSET
- 45 -

2. The current time will be displayed. To change or to set a new time press the T key

h03-25

h03-25

3. Use the following keys to change the current time


To accept and go to
next digit

4. Once the time has been set the scale will display”PM” or “AM”. Press the T key when the desired setting
is displayed.

PMM

AMM

5. Once the Time has been set, the scale will display the current date. To change or to set a new date press the
T key

d06-12

d06-12

6. Use the following keys to change the date


To accept and go to
next digit

- 46 -

7. Once the time has been set the scale will display the current year. To change the years press the T key.

y - 2010
22.3. Enabling PIN access to the Date Configuration Function.
Configuration of the current date and time can be protected with a PIN. Once set the user is prompted to enter
a pin number before time and date change is allowed.
1. To Set PIN for date configuration press the MENU key. When the option “Date” is displayed press the T
key, and then select the option “Dat PIN ” by press the T key once again.

Date

DATPIN

2. The scale will display a dashed line indicating to enter a desired PIN. To enter the PIN, use the following
keys: the C key to increment a digit, the T key to accept and go to the next digit, the
key to insert a
decimal, and the MENU key to accept the entire setting.


To accept and go to
next digit

To insert a decimal

To accept entered
PIN

3. After setting the PIN, you will be asked to key in the pin in order to access the “Date and Time” feature.
To remove or disable PIN access, enter the “Date” function and key-in the current PIN. After accessing
the “Date” menu, select option “DatPin” and do not enter a new PIN number. Simply press the MENU
key with the dashed line displayed.

_
- 47 -

Chapter 23: Threshold Check Weighing and Opto-Isolator (ThR)
Threshold check weighing is used to check whether a weight of an object falls within specified threshold
limits.
Function Options:
Thr Off
(throFF)
Thr On
(thr on)
Thr Prn
(thrPrn)
Dat Cfg
(thrCFG)

Disables threshold and check weighing.
Enables threshold weighing and sets function parameters.
Prints currently set parameters.
Sets output mode for the opto-isolator (Pulse Mode / Level Mode).

23.1. Enabling check weighing and setting threshold limits.
1. Press the MENU key, when the option “thr” is displayed press the T key, and then select the option
“thr On” by press the T key once again.

thr

thr on

2. The scale will begin to display threshold limits. To set the Lower Limit wait for “Set-1” to display and
press the T key. To set the Upper Limit wait for “Set-2” to display and press the T key. To set the
minimum weight value that should be used in check weighing select “Set-3”.

set 0

set 1

set 2

set 3

3. The scale will display a dashed line indicating to enter the limit value. To enter the value, use the


To accept and go to
next digit

- 48 -

To insert a decimal

To accept entered
value

key to

4. After setting all limit sets, select “Set-0” in order to return to weighing with the limits enabled.

set - O
5. To perform check weighing places the weigh on the Pan. The result is indicated by a dashed line located
on the left side of the display.

LOW

OK

HIGH

1.10

0.50

3.20

6. To disable check weighing enter the “thr” menu and select “thr Off”
7. To view the threshold limits press the MENU key, when the option “thr” is displayed press the T key, and
then select the option “thrPrn ” by press the T key once again.

thr

thrprn

8. Current limit sets will be displayed and transmitted via the RS-232 port. To view all limits use the T key.

LOW

HIGH
3.00

1.00

- 49 -

Min
0.20

23.2. Setting the output mode for the opto-isolator (Pulse Mode / Level Mode).
Output signals are provided for controlling sorting or signaling equipment:
• Voltage level output signals Under, OK, and Over -Signal Mode
• Pulse output signals greater than level I, greater than level II, and below the function activation level
III – Pulse mode
Signal Mode:
P1 high indicates the level III (min weight) has been passed, P2 high indicates that weight is greater
than level I, P3 high indicates that the weight is greater level II. No signal indicated that the weight is
less than min. required to activate, P1 alone =LOW, P1 and P2 without P3 = OK, P1 and P2 and P3 =
HIGH.
Pulse Mode:
P1 pulse indicates that the level I threshold has been passed, P2 pulse indicates that the level II
threshold has been passed, P3 pulse indicates that the min weight level has been passed. P3 alone = LOW,
P3 and P1 = GOOD, P3 and P1 and P2 = HIGH.

The Pulse outputs are open collector switches to ground for approximately 0.5 second. The P3 output
indicates that the minimum weight required to initiate the check weighing function has been passed. The P1
and P2 pulses will not appear unless P3 occurs.
1. To select an output mode, press the MENU key, when the option “thr” is displayed press the T key, and
then select the option “Thr Cfg ” by press the T key once again.

thr

thrCFG
- 50 -

2. The scale will display options “Impuls” and” Signal”. To select Pulse Mode press the T key when
“Impuls” is displayed, to select Signal Mode press the T key when “Signal” is displayed.

IMMPUL

SIGNAL

23.3. Opto-isolator Output

The outputs are open collector optically isolated switches. Each output has a current rating of 100.ma and an
open circuit collector voltage rating of 24 VDC. If the outputs are used to drive relays each relay should have
a flyback diode, with at least a 100.ma rating, to protect the drive transistor. If relays are used as buffers to
the sorting equipment be sure the contacts have adequate ratings and are properly protected from inductive
loads.

- 51 -

Chapter 24: Totalizing (total)
Function Options:
Tot Prn (totPRN)
Tot Off (totoff)
Tot o
(tot o)
Tot (tot -)

Displays and prints transaction total. (Does not reset the sum value)
Displays and disables the transaction total. (Resets the sum Value)
Prints measurement weigh before adding.
Adds measurement weigh to the total without printing

24.1. Performing Totalizing.
Storing a Tare Value Automatically
1. Place a container on the pan and press the T key to tare.

------2. Press the MENU key, when the option “Total” is displayed press the T key, and then select the option
“Tot o ” or “Tot –“ by press the T key once again.

total

tot -

3. The display will read 0 indicating that you may place the first object into the container. Once the Weight
of the object stabilized press the data transfer key
to accept and add the object weight to the total.

0.22
- 52 -

4. Once the weight has been added, remove the object from the weighing pan.

0.00
5. Wait for the scale to return to 0 and place the second object on the pan. . Once the Weight of the object
to accept and add the second object weight to the total.
stabilized press the data transfer key

0.55
6. Follow steps 3 through 6 until all object have been added. To view the total of the transaction press the
MENU key, when the option “Total” is displayed press the T key, and then select the option “Tot Off ” or
“Tot Prn“ by press the T key once again.

total

totoff

7. The total will be displayed. To view the number of measurements added and the average press the Menu
key.

Total

0.77

Number of measurements

n

2

- 53 -

Transaction Average

0.39

Chapter 25: Changing to Grams (g) or Pounds (lbs) (LB_BAL)
The function “lb bal” is used to configure the unit to weigh in grams (g) or pounds (lb). “Lb Bal” optimize
the scale’s accuracy and resolution disabling or enabling ponds (lb) as a default unit of measure.
1. To disable lb (pounds) as default unit of measure and set the scale weigh in grams (g) .Press the MENU
key, when the option “lb_bal” is displayed press the T key.

LB_BAL
2. The scale will display options “Lb Off” and” Lb On”. To select disables pounds and select grams as the
default unit of measure press the T key when “Lb Off” is displayed, to disables grams and select pounds
and the default unit of measure press the T key when “Lb Ob” is displayed.

Lb off

Lb on

- 54 -

Chapter 26: Menu Customization (AcTIU)
The Active function is used to customize the scale’s Main Menu. This feature should be used to deactivate
functions or features that are not used. Deactivated functions will not appear in the Main Menu which will
simplify its use. To activate or deactivate features or function follow the steps below.
1. Press the MENU key, when the option “Active” is displayed press the T key, and then select a desired
function or feature by press the T key once again when the name is displayed.

ACTIu

Avtota

2. The scale will display options “ON” and” Off”. To disable a function from appearing in the Main Menu
press the T key when “Off” is displayed, to enable a function to have it appear in the Main Menu press the
T key when “On” is displayed.

ON

OFF

Chapter 27: Resorting Default Settings (DEFAUL)
To restore the scale’s factory settings follow the steps below
1. Press the MENU key, when the option “Default” is displayed press the T key.

DefauL
2. The scale will display options “Yes” and” No”. To restore the scale’s factory setting press the T key when
“Yes” is displayed. To cancel press the T key when “No” is displayed.

YES

NO
- 55 -

Chapter 28: Common Errors and Troubleshooting
Error or Indicator
----

Cause
Below zero

--

L
H

Err - b
Sapl LO (Parts Counting)
Sapl LO (Percent Weighing)
The scale will not turn on
Weighing results are not accurate
Weighing result will not stabilize

Explanation / Solution
Re-zero the scale by pressing the
0 key.
Taring is not allowed
Place a weight on the pan before
taking a tare.
Re-zeroing is not allowed
Remove weight from pan and clear
stored tare values.
Pan error
Make sure that pan is properly
seated on the pan support.
Exceeded capacity
The scale has exceeded its
weighing capacity. Reduce the
weight.
Pan not cleared on power-up
The pan was not empty while the
scale was initiating at startup.
Clear the pan and restart the scale.
Average piece weight is too low
The average piece weight is lower
than 3e. Be sure that individual
piece weight is greater than 3e.
Sample reference weight is too low The sample reference weight is
lower than 100d. Increase the
sample weight.
Possible power failure
Check the power AC adapter
connection.
Inaccurate calibration
Calibrate the scale.
Irregular environment
Eliminate drafts or vibrations.

Chapter 29: Maintenance
Cleaning and maintaining your Scale:
•
•
•
•
•
•

Before cleaning the scale always unplug the A/C adapter from the electrical outlet.
Use a soft, slightly damp cloth to clean the exterior housing of your scale,.
Wipe the scale gently. Do not allow any liquid to enter into the scale.
Do not apply extensive pressure to the LCD or the LED display.
Do not use chemicals or benzene when cleaning the surface. Corrosive chemicals may damage the
finish.
Alcohol may be used only to clean the scale’s stainless steel pan or the draft ring.

- 56 -

Chapter 30: Limited Warranty
PURCHASER’S 12-MONTH WARRANTY
Warranty is valid only if the attached warranty registration card is completed and returned within 30 days.
This product is a precision device made to exacting standards of scientific accuracy. It is guaranteed to have
been adjusted and inspected for proper workmanship and performance, and certified for its currently
advertised specifications before shipment.
Fulcrum Products are warranted against defects in material and workmanship under normal use and service.
This warranty is extended only to the first purchaser. This limited warranty will not apply if, upon inspection,
it is found that the product was tampered with, misused, overloaded, or abused,mishandled, placed in an
improper environment, improperly installed or adjusted, used for a purpose other than that for which it was
designed, or repaired by unauthorized personnel.
Fulcrum’s liability under this warranty is limited to furnishing labor and parts necessary to remedy the defect
covered by this warranty and restore the product to normal operating condition. Purchasers may be charged a
minimum repair fee for in-warranty products returned for repair if those products are determined to be
problem-free.
To make a claim under this limited warranty, obtain an RMA number from Fulcrum and return the
product, carefully packed in its original packaging, shipping prepaid, with the RMA number written on the
return package.

- 57 -

Fulcrum Inc.
100 Delawanna Ave.,#120
Clifton, NJ 07014
(973) 473 6900
(973) 777 8302
http://www.fulcruminc.net

Torbal platform balance

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to Torbal platform balance (20)

Recently uploaded (20)

Torbal platform balance