Transducers and Sensor an introduction -Lect9.pdf

AMSS-MSc Prof. Kasim Al-Aubidy 1
Lecture (9)
Force, Pressure, and Tactile
Sensors
Prof. Kasim M. Al-Aubidy
Philadelphia University-Jordan

Force:
 When force is applied to a free body, it gives the body an acceleration in a direction
of the force. Thus, force is a vector value.
 Newton had found that acceleration (a) is proportional to the acting force (F) and
inversely proportional to the property of a body called the mass (m);
a= F/m
 This is Newton’s 2nd law, while 1st law is “when net acting force F=0, then a=0”
 Newton’s 3rd law: “To every action there is always opposed an equal reaction; or,
the mutual actions of two bodies upon each other are always equal, and directed to
contrary parts.”
 Density is defined through mass (m) and volume (V) as;
ρ= m/V

Force Sensors:
Force sensors can be divided into two classes:
1. Quantitative sensor: It measures the force and represents its value in terms of an
electrical signal.
Examples: strain gauges and load cells.
2. Qualitative sensor: It indicates whether a sufficiently strong force is applied or
not. The sensor output signal indicates when the force magnitude exceeds a
predetermined threshold level.
Example: computer keyboard.
The qualitative force sensors are used for detection of motion and position.
Note: Whenever pressure is measured, it requires the measurement of force. Force is
measured when dealing with solids, while pressure is measured when dealing
fluids. That is, force is considered when action is applied to a spot, and pressure is
measured when force is distributed over a relatively large area.

Methods of Sensing Force:
1. By balancing the unknown force against the gravitational force of a standard mass
2. By measuring the acceleration of a known mass to which the force is applied
3. By balancing the force against an electromagnetically developed force
4. By converting the force to a fluid pressure and measuring that pressure
5. By measuring the strain produced in an elastic member by the unknown force
Force sensors are complex sensors, since force is
not directly converted into an electric signal. The
LVDT sensor produces voltage proportional to the
applied force within the linear range of the spring.
For example; force sensor can be fabricated by
combining a force-to displacement transducer and a
position (displacement) sensor. The former may be
a simple coil spring, whose compression
displacement (x) can be defined through the spring
coefficient (k) and compressing force (F) as;
X= k F

Strain Gauges :
Strain (e): is deformation of a physical body under the
action of applied forces.
 Strain gauge is a resistive elastic sensor whose resistance
is function of the applied strain.
 Resistance is related to the applied force, and this is
called the piezoresistive effect.
where;
Se : is the gauge factor, (Se  2 for most materials except
for platinum Se 6).
dR: is the change in resistance caused by strain (e),
R: is the resistance of the undeformed gauge.
 For small variations in resistance (less than 2%), the
resistance of the metallic wire is given by:
R = Ro (1+x)
where; Ro is the resistance with no stress applied,
x= Se e

gauge and three dummy resistors in a Wheatstone Bridge configuration, the output (v)
from the bridge is:
Where; V is the bridge excitation voltage.
Foil gauges typically have active areas of about 2–10 mm2 in size. With careful
installation, the correct gauge, and the correct adhesive (glue), strains up to at least 10%
can be measured. Gauge factor is given by;
Se =1+2μ
where μ= Poisson's ratio.
Strain-Gage Based Pressure Cell:

Tactile Sensors
The tactile sensors can be subdivided into three subgroups:
1. Touch Sensors: detect and measure contact forces at defined points. A touch
sensor typically is a threshold device or a binary sensor (touch or no touch).
Note: Some touch sensors do not rely on reaction to a force. A touch by a finger
may be detected by monitoring a contact area between the finger and the panel. An
example is a touch screen on a mobile telephone.
2. Spatial Sensors: These sensors detect and measure the spatial distribution of
forces perpendicular to a predetermined sensory area, and the subsequent
interpretation of the spatial information.
3. Slip Sensors: These sensors detect and measure the movement of an object relative
to the sensor. This can be achieved either by a specially designed slip sensor or by
the interpretation of the data from a touch sensor or a spatial array.
Note: A spatial-sensing array can be considered to be a coordinated group of touch
sensors.

Tactile Sensors Requirements:
Requirements to tactile sensors are based on investigation of human sensing and
the analysis of grasping and manipulation.
Example: the desirable characteristics of a touch or tactile sensor suitable for the
majority of industrial applications are;
1. It should be a single-point contact, though the sensory area can be any size. In
practice, an area of 1–2 mm2 is considered a satisfactory.
2. The sensor sensitivity is dependent on a number of variables determined by the
sensor’s basic physical characteristics. In addition, the sensitivity depends on the
application.
3. A minimum sensor bandwidth of 100 Hz.
4. The sensor characteristics must be stable and repeatable with low hysteresis.

Switch Sensors :
A simple tactile sensor producing an “on–off”
output can be formed with two leaves of foil and
a spacer .
The spacer has holes. One leaf is grounded and
the other is connected to a pull-up resistor.
A multiplexer can be used if more than one
sensing area is required.
When an external force is applied to the upper
conductor over the hole in the spacer, the top leaf
flexes and upon reaching the lower conductor,
makes an electric contact, grounding the pull-up
resistor. The output signal becomes zero
indicating the applied force.

The bottom piezoelectric film is driven by an AC voltage (Oscillator). This signal
results in mechanical contractions of the film that are coupled to the compression film
and, in turn, to the upper piezoelectric film, which acts as a receiver.
Since piezoelectricity is a reversible phenomenon, the upper film produces alternating
voltage upon being subjected to mechanical vibrations from the compression film.
These oscillations are amplified and fed into a synchronous demodulator, which is
sensitive to both the amplitude and the phase of the received signal.
When force (F) is applied to the upper film, mechanical coupling between layers
changes. This affects the amplitude and the phase of the received signal. These changes
are recognized by the demodulator and appear at its output as a variable voltage.
Piezoelectric Sensors
They can be designed with piezoelectric
films, such as Polyvinylidene Fluoride
(PVDF) used in active or passive modes.
The center film is for the acoustic coupling
between the other two. The softness of the
center film determines sensitivity and the
operating range of the sensor.

Example: A PVDF film tactile sensor for detecting breathing rate of a sleeping child
Movements of a body had to be monitored in order to detect cessation of breathing. The
sensor was placed under the mattress in a crib. A body of a normally breathing child
slightly shifts with each inhale and exhale due to a moving diaphragm. This results in a
displacement of the body’s center of gravity that is detected by the PVDF film sensor.
The sensor consists of three layers where the PVDF film is positioned between a
backing material (silicone rubber) and a pushing layer (plastic film).
The film generates an electric current converted into output voltage. The amplitude
of that voltage within certain limits is proportional to the applied gravitational force.

Piezoresistive Sensors:
The sensor incorporates a Force-Sensitive Resistor (FSR)
whose resistance varies with applied pressure.
A conductive elastomer is fabricated of silicone rubber,
polyurethane, and other compounds that are impregnated
with conductive particles or fibers.
Operating principles of elastomeric tactile sensors are
based either on varying the contact area when the
elastomer is squeezed between two conductive plates or
in changing the thickness.
When the external force varies, the contact area at the
interface between the pusher and the elastomer changes,
resulting in a reduction of electrical resistance.
At a certain pressure, the contact area reaches its maximum and the transfer function
goes to saturation. For a resistive polymer having thickness 70 mm and a specific
resistance of 11 kΩ/cm2, resistance for pressures over 16 kPa can me approximated by;

Capacitive Touch Sensor:
It relies on the applied force that either changes
the distance between the plates or the variable
surface area of the capacitor.
To maximize the change in capacitance as
force is applied, it is preferable to use a high
permittivity dielectric (such as PVDF) in a
coaxial capacitor design.
To measure the change in capacitance;
1. Use of a current source with a resistor and measure the time delay caused by a
variable capacitance.
2. Use the sensor as part of an oscillator with an LC or RC circuit, and measure the
frequency response.

Capacitive Pressure Sensor
Capacitive pressure sensors are also used in electronic pressure transmitters. With these
devices the change in capacitance resulting from the movement of an elastic element is
proportional to the pressure applied to the elastic element.

Force and Pressure Measurements:
• Force and Pressure generally measured indirectly through deflection of an alternate
surface.
Mechanism include:
 Physical motion and measurement using an LVDT.
 Strain gauges: metal that changes resistance when
stressed.
 Piezoelectric materials that generate a current when
deformed.

They use an array of infrared (IR) light-emitting diodes (LEDs) on two adjacent bezel
edges of a display, with photo detectors placed on the two opposite bezel edges to
analyze the system and determine a touch event.
The LED and photo detectors pairs create a grid of light beams across the display. An
object that touches the screen changes the reflection due to a difference between
refractive properties of air and a finger.
This results in a measured decrease in light intensity at the corresponding photo
detector. The measured photo detector outputs can be used to locate a touch-point
coordinate.
Optical-Touch Sensor:

PRESSURE TRANSDUCERS:
 Pressure sensors either convert the pressure into mechanical movement or into an
electrical output.
 Complete gauges not only sense the pressure but indicate them on a dial or scale.
 Mechanical movement is produced with the following elements.
1. Spring and Piston.
2. Bourdon Tube.
3. Bellows and capsules.
4. Diaphragm.
1. PISTON TYPE:
The pressure acts directly on the piston and compresses the spring.
The position of the piston is directly related to the pressure.
A window in the outer case allows the pressure to be indicated.
This type is usually used in hydraulics where the ability to
withstand shock, vibration and sudden pressure changes is needed
(shock proof gauge). The piston movement may be connected to a
secondary device to convert movement into an electrical signal.

2. Bourdon tube:
 The Bourdon tube is a hollow tube with an
elliptical cross section. When a pressure
difference exists between the inside and
outside, the tube tends to straighten out and
the end moves.
 The movement is usually coupled to a needle
on a dial to make a complete gauge.
 It can also be connected to a secondary
device such as an air nozzle to control air
pressure or to a suitable transducer to convert
it into an electric signal. This type can be
used for measuring pressure difference.

3. CAPSULES AND BELLOWS:
 A bellows is made of several capsules (hollow flattened
structures made from thin metal plate).
 When pressurized the bellows expand and produce
mechanical movement. If the bellows is encapsulated
inside an outer container, then the movement is
proportional to the difference between the pressure on
the inside and outside.
 Bellows and single capsules are very useful for
measuring small pressures.
4. DIAPHRAGMS:
 These are similar in principle to the capsule but the
diaphragm is usually very thin and perhaps made of
rubber.
 The diaphragm expands when very small pressures are
applied.
 The movement is transmitted to a pointer on a dial
through a fine mechanical linkage.

ELECTRICAL PRESSURE TRANSDUCERS:
The mechanical movement of the preceding types can be converted into an electric
signal using;
 Strain Gauge types.
 Piezo electric types.
 Other electric effects.
1. STRAIN GAUGE TYPES:
 Strain gauges are small elements that are fixed to a surface
that is strained. The change in length of the element
produces changes in the electrical resistance.
 This is processed and converted into a voltage. A typical
pressure transducer would contain a metal diaphragm
which bends under pressure.

2. PIEZO ELECTRIC TYPES:
 The element used here is a piece of crystalline material that produces an electric
charge on its surface when it is mechanically stressed.
 The electric charge may be converted into voltage. When placed inside a pressure
transducer, the pressure is converted into an electric signal.
3. OTHER ELECTRIC EFFECTS: (CAPACITIVE and INDUCTIVE)
 The pressure produces a change in the capacitance or inductance of an electronic
component in the transducer.
 Both these effects are commonly used in an electronic oscillator and one way they
may be used is to change the frequency of the oscillation. The frequency may be
converted into a voltage representing the pressure.

Elastic sensing elements:
If a force is applied to a spring, then the amount of extension or compression of the
spring is approximately proportional to the applied force.
Elastic elements are also commonly used for measuring torque, pressure and
acceleration, which are related to force by the equations:
 The dynamics of a mass–spring–damper force sensor has a 2nd order T.F.;

Pressure Sensing:
 For a fluid at rest, pressure is the force (F) exerted perpendicularly on a unit area
(A) of a boundary surface, and is given by: P= dF/dA
 Kinetic theory of gases states that pressure can be viewed as a measure of the total
kinetic energy of the molecules “attacking” the surface;
where;
KE: is the kinetic energy, V: is the volume,
ρ: is the density, N: is the number of molecules per unit volume,
R: is a specific gas constant, and T: is the absolute temperature.
C2: is an average value of the square of the molecular velocities,
Example: At 0°C and 1 atm. pressure, air has a density of 1.3 kg/m3, while at the same
temperature and 50 atm. pressure its density is 65 kg/m3, which is 50 times higher.
For liquids the density varies very little over ranges of pressure and temperature. For
water at 0C and 1 atm. has a density of 1,000 kg/m3, while at 0C and 50 atm., its
density is 1,002 kg/m3, and at 100C and 1 atm. its density is 958 kg/m3.

Absolute and Relative Pressure:
Relative Pressure: when it is measured with respect to ambient pressure.
Absolute Pressure: when it is measured with respect to a vacuum at zero pressure.
Static Pressure: The pressure of a medium is static when it is referred to fluid at rest.
Dynamic Pressure: when it is referred to kinetic energy of a moving fluid.
Pressure Units:
The SI unit of pressure is the pascal: 1 Pa = 1 N/m2.
One atmosphere (atm) is the pressure exerted on 1 cm2 by a column of water having
height of 1 m at a temperature of 4°C and normal gravitational acceleration.
One pascal may be converted into other units by the use of following relationships:
 Pound / Square Inch = PSI
 Newton / Square Meter = N/m2
 100,000 N/m2 = 1 Bar
 14.5 psi = 1 Bar

Pressure in Industry:
Torr: It is defined as pressure exerted by 1 mm column of mercury at 0°C at normal
atmospheric pressure and normal gravity.
1 Torr = 1 mmHg
The ideal pressure of the Earth atmosphere is 760 Torr (mmHg) and is called the
physical atmosphere
1 atm = 760 Torr = 101.325 Pa
The U.S. Customary System of units defines pressure as a pound per square inch (psi).
Conversion into SI systems is the following:
1 psi = 6.89 * 103 Pa = 0.0703 atm

Mercury Pressure Sensor:
A U-shaped wire is immersed into mercury, which
shorts its resistance in proportion with the height of
mercury in each column. The resistors are connected
into a Wheatstone bridge circuit that remains in
balance as long as the differential pressure is zero.
Pressure is applied to one of the arms of the tube and
disbalances the bridge, which results in the output
signal. The output voltage is proportional to R of the
wire arms that are not shunted by mercury:
The sensor is simple and can be directly calibrated in units of Torr.
Drawbacks:
 large size,
 necessity of precision leveling,
 susceptibility to shocks and vibration,
 contamination of gas by mercury vapors

Bellows, Membranes, and Thin plates:
A bellows is a first step in the complex conversion of pressure into an electrical signal.
It is used to convert pressure into a linear displacement, which can be measured by an
appropriate sensor.
A membrane is a thin diaphragm under radial tension (S),
which is measured in N/m.
At low-pressure (p) differences across the membrane, the
center deflection (zmax) and the stress (σmax) are functions
of pressure:
where: r is the membrane radius,
g is the thickness.

Piezoresistive Sensors:
Two components are required to design a pressure sensor:
- the plate (membrane) having known area (A) and
- a detector that responds to applied force (F).
Both these components can be fabricated of silicon.
 A silicon-diaphragm pressure sensor consists of a thin silicon
diaphragm and piezoresistive gauge resistors.
 When stress is applied to a semiconductor resistor (R),
piezoresistive effect results in change in the resistance (R);
where; (πl and πt) and (σl and σt) are the piezoresistive coefficients and stresses in a
longitudinal and transverse directions, respectively. The π-coefficients depend on
the orientation of resistors on the silicon crystal.
 A change in resistivity is proportional to applied stress and to applied pressure.
 When connecting R1 & R2 in a half-bridge circuit, the output voltage is;

Temperature characteristics of a piezoresistive pressure sensor:

Capacitive Pressure Sensor:
 The diaphragm displacement modulates capacitance with respect to the reference
plate. It is especially effective for the low-pressure sensors.
 An entire sensor can be fabricated from a solid piece of silicon, thus maximizing its
operational stability.
 To design a capacitive pressure sensor, for good linearity, it is important to
maintain flatness of the diaphragm. These sensors are linear only over the
displacements that are much less then their thickness.

Variable Reluctance Pressure (VRP) Sensor:
It uses a magnetically conductive diaphragm to modulate the magnetic resistance of a
differential transformer .
The inductance of the circuit, is inversely proportional to the magnetic reluctance (i.e.
X1,2 = k/d, where k is a constant and d is the gap size.).
When the bridge is excited by a carrier current, the output signal across the bridge
becomes amplitude-modulated by the applied pressure. The amplitude is proportional to
the bridge imbalance, and the phase of the output signal changes with the direction of
the imbalance. The ac signal can be demodulated to produce a dc response.

Optoelectronic Pressure Sensors:
An optical readout has several advantages over
other technologies;
 a simple encapsulation,
 small temperature effects, and
 high resolution and accuracy.
An optical sensor consists of: a passive optical
pressure chip with a membrane etched in silicon,
a LED, and a detector chip.
A pressure chip with optical cavity forming a Fabry–Perot (FP) interferometer
measuring the deflection of the diaphragm.
A back-etched, single-crystal diaphragm on a silicon chip is covered with a thin
metallic layer, and a glass plate with a metallic layer on its backside.
A detector chip contains three pn-junction photodiodes. Two of them are covered with
integrated optical FP filters of slightly different thicknesses.
The detector chip works as a demodulator and generates electrical signals representing
the applied pressure.

References:
1. Jacob Fraden, “Handbook of Modern Sensors; Physics, Design, and Applications”, Fourth Edition,
Springer Press 2010.
2. Kelley CT (2003) Solving nonlinear equations with Newton’s method, No. 1 Fundamentals of
Algorithms. SIAM, Philadelphia, PA
3. ISO guide to the expression of uncertainty in measurements (1993) International Organization for
Standardization, Geneva, Switzerland
4. Taylor BN, Kuyatt CE (1994) Guidelines for evaluation and expressing the uncertainty of NIST
measurement results. NIST Technical Note 1297. US Government Printing Office, Washington DC
5. Widlar RJ (1980) Working with high impedance Op Amps, AN24, Linear Application Handbook.
National Semiconductor
6. Sheingold DH (ed) (1986) Analog-Digital Conversion Handbook. 3rd ed., Prentice-Hall, Englewood
Cliffs, NJ.
7. Williams J (1990) Some techniques for direct digitization of transducer outputs, AN7, Linear Technology
Application Handbook.
8. Long DJ (1975) Occupancy detector apparatus for automotive safety system. US Patent 3,898,472, 5 Aug
9. Park YE, Wise KD (1983) An MOS switched-capacitor readout amplifier for capacitive pressure sensors.
IEEE Custom IC Conf 380–384.
10. Ryser P, Pfister G (1991) Optical fire and security technology: sensor principles and detection
intelligence. In: Transducers’91. International conference on solid-state sensors and actuators. Digest of
technical papers, pp 579–583, IEEE.
11. Consolidated Electrodynamics, Bulletin 4202B/1167 on Type 4-202 Strain Gauge Accelerometer.
12. http://www.instrumentationtoday.com/

Transducers and Sensor an introduction -Lect9.pdf

More Related Content

Similar to Transducers and Sensor an introduction -Lect9.pdf (20)

More from ssuser672f82 (8)

Recently uploaded (20)

Transducers and Sensor an introduction -Lect9.pdf