Tutorial for EDA Tools:

DelftUniversityofTechnology
Code ET4351
Digital Design Flow
Tutorial for EDA Tools:
Synopsys Design Compiler
Mentor Modelsim
Cadence SOC Encounter V14.1
Ir. A.C. de Graaf
Dr. ir. T.G.R. van Leuken

Preface
This document describes the top-down design ﬂow of the implementation a SoC design. Starting from
an example HDL description the designer is guided through all the design steps to tapeout GDS2 layout
description.
This tutorial is derived from "Top-Down digital design ﬂow" version 3.1 (November 2006) by Alain Va-
choux, Microelectronic Systems Lab EPFL, Lausanne, Switzerland.
i

Contents
1 Introduction 1
1.1 Top-down design flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Design project organisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 VHDL example: FIR-Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Design flow steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 VHDL and Verilog simulation 11
2.1 Starting the Modelsim graphical environment . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 Simulation of (pre-synthesis) RTL VHDL models . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Simulation of the post-synthesis Verilog model with timing data . . . . . . . . . . . . . . 14
2.4 Simulation of the post-route Verilog model with timing data . . . . . . . . . . . . . . . . 15
3 Logic synthesis 17
3.1 Starting the Design Vision graphical environment . . . . . . . . . . . . . . . . . . . . . . 17
3.2 RTL VHDL model analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3 Design elaboration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 Design environment definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.5 Design constraint definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.6 Design mapping and optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.7 Report generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.8 VHDL/Verilog gate-level netlist generation and post-synthesis timing data (SDF) extraction 28
3.9 Design constraints generation for placement and routing . . . . . . . . . . . . . . . . . . 29
3.10 Design optimization with tighter constraints . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.11 Using scripts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4 Standard cell placement and routing 31
4.1 Starting the Encounter graphical environment . . . . . . . . . . . . . . . . . . . . . . . . 31
4.2 Generate uniquified netlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3 Design import . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4 Floorplan Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.5 Global net connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.6 Power ring/stripe creation and routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.7 Operating conditions definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.8 Core cell placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.9 Post-placement timing analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.10 Clock tree synthesis (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.11 Filler cell placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.12 Design routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
ii

CONTENTS iii
4.13 Post-routing timing optimization and analysis . . . . . . . . . . . . . . . . . . . . . . . . 46
4.14 Design checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.15 Report generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.16 Post-route timing data extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.17 Post-route netlist generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.18 GDS2 file generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.19 Using scripts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
A Appendix A: VHDL Netlists 56
A.1 File: filter.vhd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
A.2 File: filter_top.vhd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
A.3 File: filter_soc.vhd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
A.4 File: filter_soc_tb.vhd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
B Appendix B: Technology independent IO-cell library 67
C Appendix C: Tool Scripts 69
C.1 Synopsys: Design Compiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
C.2 Cadence: SOC Encounter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
C.2.1 start.tcl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
C.2.2 fplan.tcl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
C.2.3 pplan.tcl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
D Appendix D: Design Metrics 76

Chapter 1
Introduction
This document details the typical steps of a top-down digital VHDL/Verilog design flow with the help of
one simple design example.
The following tools are considered in this document:
• Modelsim v10.1 or higher, from Mentor Graphics.
• Design Compiler and Design Vision D-2010.03 or higher from Synopsys.
• Encounter 9.12 or higher from Cadence Design Systems.
The design kit used is from Faraday. The process is L90_SP, a 90 nm 9-metal CMOS process. Each of the
next chapters in this document is addressing a specific set of tasks. Chapter 2 is about VHDL and Verilog
simulation, chapter 3 is about logic synthesis and chapter 4 is about place and route. Steps in these chapters
are not necessarily to be done in the given sequence. Go to “1.4 Design flow steps” to get a typical sequence
of steps supporting a top-down approach.
1.1 Top-down design flow
Figure 1.1: Top-down design flow
1

CHAPTER 1. INTRODUCTION 2
Figure 1.1 illustrates the top-down flow that includes the following steps:
VHDL RTL model creation
The goal here is to develop synthesizable VHDL models at the RTL level (RTL means Register-
Transfer Level). Such models usually define a clear separation between control parts (e.g. finite
state machines-FSM) and operative parts (e.g. arithmetic and logic units). Registers are used to store
small size data between clock cycles. RAM/ROM memories are used to store large amounts of data
or program code. Blocks such as FSMs, ALUs, registers are usually described as behavioral models
that do not imply any particular gate-level implementation. Tools used at this step can range from
simple text editors to dedicated graphical environments that generate VHDL code automatically.
RTL simulation
The VHDL RTL models are validated through simulation by means of a number of testbenches also
written in VHDL.
RTL synthesis
The synthesis process infers a possible gate-level realization of the input RTL description that meets
user-defined constraints such as area, timings or power consumption. The design constraints are de-
fined outside the VHDL models by means of tool-specific commands. The targeted logic gates belong
to a library that is provided by a foundry or an IP company as part of a so-called design kit. Typical
gate libraries include a few hundreds of combinational and sequential logic gates. Each logic function
is implemented in several gates to accommodate several fan-out capabilities or drive strengths. The
gate library is described in a tool-specific format that defines, for each gate, its function, its area, its
timing and power characteristics and its environmental constraints.
The synthesis step generates several outputs: a gate-level VHDL netlist, a Verilog gate-level netlist,
and a SDF description. The first netlist is typically used for post-synthesis simulation, while the
second netlist is better suited as input to the place&route step. The SDF description includes delay
information for simulation. Note that considered delays are at this step correct for the gates but only
estimated for the interconnections.
Post-synthesis gate-level simulation
The testbenches used for RTL model validation can be reused (with possibly some modifications to
use the VHL gate-level netlists). The gate-level simulation makes use of VHDL models for the logic
gates that are provided in the design kit. These VHDL models follow the VITAL modeling standard
to ensure proper back-annotation of delays through the SDF files generated by the synthesis or the
place&route step.
Standard cell place and route
The place&route (P&R) step infers a geometric realization of the gate-level netlist so-called a layout.
The standard cell design style puts logic cells in rows of equal heights. As a consequence, all logic
gates in the library have the same height, but may have different widths. Each cell has a power rail at
its top and a ground rail at its bottom.
The interconnections between gates are today usually done over the cells since current processes
allow several metal layers (i.e. 9 metal layers for the Faraday L90_SP process). As a consequence,
the rows may be abutted and flipped so power and ground rails are shared between successive rows.
The P&R step generates several outputs: a geometric description (layout) in GDS2 format, a SDF
description and a Verilog gate-level netlist. The SDF description now includes interconnect delay.
The Verilog netlist may be different from the one read as input as the P&R step may make further
timing optimizations during placement, clock tree generation and routing (e.g. buffer insertion).
Post-layout gate-level simulation

The Verilog gate-level netlist can be simulated by using the existing VHDL testbenches and the more
accurate SDF data extracted from the layout.
System-level integration
The layout description is then integrated as a block in the designed system. This step is not covered
in this document.
1.2 Design project organisation
First we have to setup a proper work environment. The toolscripts need the CSH shell as command shell
while the standard shell after login is the Bash shell. So first we take care that the CSH shell is our default
command shell by:
cp /opt/eds/DesignLab/bin/dot.bashrc ~/.bashrc
Now close the current terminal window and start a new terminal. Then add the DesignLab script directory
to our PATH by:
source /opt/eds/DesignLab/bin/dlab.csh
Given the number of EDA tools and files used in the flow, it is strongly recommended to organize the
working environment in a proper way. To that end, the create_eda_project script can be used to create a
directory structure in which design files will be stored.
The use of the script is as follows:
create_eda_project <project-name>
where <project-name> is the name of the top-level directory that will host all design files for the projects.
For example, to create the project directory called FILTER that will be used to do the tasks presented in the
rest of this document, execute the following command:
student@tango> create_eda_project FILTER
student@tango> cd FILTER
The FILTER top-level directory hosts the configuration files for logic simulation (Modelsim), logic synthe-
sis (Synopsys DC) and standard cell place and route (Cadence SoC Encounter). As a consequence, it is
required that the tools are always started from that point.
Figure 1.2 gives the proposed directory structure and the role of each subdirectory. The actual use of the
subdirectories and files will be explained while going throughout the tutorial in this document.

1.3 VHDL example: FIR-Filter
The FIR-Filter example will be used as the reference design throughout the topdown flow.
To install the VHDL model and its associated testbenches in the project directory, enter the following
command in the top-level project directory FILTER:
student@tango-FILTER> install_design filter
In order to use the EDA tools and Faraday design kit, a script file called edadk.csh with the necessary PATHs
to the tools exists in the directory from which the tools are launched (the top-level project directory).
Add these PATHs to your current environment by executing:
student@tango-FILTER> source edadk.csh
For information on the FARADAY design kits, find the FARADAY documentation in
/opt/eds/DesignLab/tech/Faraday/L90_SP/Docs.
Listing 1.1 gives the entity declaration of the VHDL model of a generic 128 tap FIR-Filter. You will
find the complete VHDL model in Appendix A.1-3. We will call this model the Core.
Listing 1.1: Entity declaration of a synthesisable 128 tap FIR-Filter.
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;
entity filter_soc is
generic (
CWIDTH : integer := 16;
CAW : integer := 7;
DWIDTH : integer := 16;
DAW : integer := 7
);
port (
ClkxCI : in std_logic;
ResetxRBI : in std_logic;
DataInxDI : in std_logic_vector(DWIDTH -1 downto 0);
DataInReqxSI : in std_logic;
DataInAckxSO : out std_logic;
DataOutxDO : out std_logic_vector(DWIDTH -1 downto 0);
DataOutReqxSO : out std_logic;
DataOutAckxSI : in std_logic
);
end filter_soc;

Figure 1.3 shows the hierarchy of the filter design. The chiplevel entity named filter_soc consists of compo-
nents IO-padcells and the toplevel filter design filter_top. Filter top consists of instances of the components
coeff, dataRam and filter. The IO-padcells connect the port signals to the outside world. For this purpose
we will use a technology independent library with generic components for IO cells defined in the library
techmap. See Appendix B for the usage of IO-padcells.
Filter_top
Filter
DataRamCoeff Rom
Filter_soc
Figure 1.3: Hierarchy of the FIR filter chip

Listing 1.2 gives the testbench for the RTL model (file filter_soc_tb.vhd). The testbench for the mapped
netlist (file filter_soc_mapped_tb.vhd) can also be used for the simulation of the placed and routed Verilog
netlist. The file filter_top.io defines the positions of the IO pins for place and route.
Listing 1.2: VHDL testbench for the RTL model with N=128.
--------------------------------------------------------------------------------
--
-- Title: Test Bench for Finite Impulse Response (FIR) Filter
--
-- Copyright (c) 1998,1999 by Mentor Graphics Corporation. All rights reserved.
--
-- This source file may be used and distributed without restriction provided
-- that this copyright statement is not removed from the file and that any
-- derivative work contains this copyright notice.
--
--------------------------------------------------------------------------------
LIBRARY ieee;
USE ieee.std_logic_1164.ALL;
USE ieee.std_logic_arith.ALL;
USE ieee.std_logic_signed.ALL;
USE ieee.math_real.ALL;
ENTITY filter_soc_tb IS
GENERIC( clock_delay : time := 16 ns;
CAW : integer := 7;
DAW : integer := 7
);
END filter_soc_tb;
ARCHITECTURE behavioral OF filter_soc_tb IS
component filter_soc is
generic (
CAW : integer := 7;
DAW : integer := 7
);
port (
);
end component;
SIGNAL ClkxCI : std_logic;
SIGNAL ResetxRBI : std_logic;
SIGNAL DataInxDI : std_logic_vector(DWIDTH -1 downto 0);
SIGNAL DataInReqxSI : std_logic;
SIGNAL DataInAckxSO : std_logic;
SIGNAL DataOutxDO : std_logic_vector(DWIDTH -1 downto 0);
SIGNAL DataOutReqxSO : std_logic;

SIGNAL DataOutAckxSI : std_logic;
BEGIN
-- Instantiate device-under-test.
dut: filter_soc
generic map (
CWIDTH => CWIDTH ,
CAW => CAW ,
DWIDTH => DWIDTH ,
DAW => DAW)
port map (
ClkxCI => ClkxCI ,
ResetxRBI => ResetxRBI ,
DataInxDI => DataInxDI ,
DataInReqxSI => DataInReqxSI ,
DataInAckxSO => DataInAckxSO ,
DataOutxDO => DataOutxDO ,
DataOutReqxSO => DataOutReqxSO ,
DataOutAckxSI => DataOutAckxSI
);
clock_generation:
PROCESS
BEGIN
-- Generate equal duty-cycle clock.
ClkxCI <= ’0’;
WAIT FOR ( clock_delay / 2 );
ClkxCI <= ’1’;
END PROCESS clock_generation;
generate_stimulus:
PROCESS
BEGIN
-- Initialize input signals.
DataInReqxSI <= ’0’;
DataInxDI <= ( OTHERS => ’0’ );
DataOutAckxSI <= ’0’;
-- Reset the design and wait for 2 clock cycles.
ResetxRBI <= ’0’;
WAIT FOR clock_delay * 2;
-- Wait for 2 more clock cycles before beginning test.
DataInxDI <= ( 0 => ’1’, OTHERS => ’0’ );
WAIT FOR clock_delay;
FOR I IN 127 DOWNTO 0 LOOP
WHILE DataInAckxSO= ’0’ LOOP
END LOOP;

WHILE DataOutReqxSO = ’0’ LOOP
END LOOP;
END LOOP;
--
-- Wait forever.
--
WAIT;
END PROCESS generate_stimulus;
END behavioral;
The file filter_soc_syn.tcl in directory SYN/BIN is a Tcl script that performs synthesis of the VHDL model
in batch mode. The file filter_top_par.tcl in directory PAR/BIN is a Tcl script that performs the placement
and routing of the synthesized Verilog netlist in batch mode.
1.4 Design flow steps
Here are the main steps of the top-down design flow with references to the sections in the document that
give more details.
Step 1) Pre-synthesis VHDL simulation (tool: Modelsim)
2.1 Compilation of the RTL VHDL model and related testbench [2.2]
2.2 Simulation of the RTL VHDL model
Step 2) Logic synthesis (tool: Synopsys Design Compiler)
3.1 RTL VHDL model analysis [3.2]
3.2 Design elaboration (generic synthesis) [3.3]
3.3 Design environment definition (operating conditions, wire load model) [3.4]
3.4 Design constraint definitions (area, clock, timings) [3.5]
3.5 Design mapping and optimization (mapping to gates) [3.6]
3.6 Report generation [3.7]
3.7 VHDL gate-level netlist generation [3.8]
3.8 Post-synthesis timing data (SDF) generation for the VHDL netlist [3.8]
3.9 Verilog gate-level netlist generation [3.8]
3.10 Design constraints generation for placement and routing [3.9]
Step 3) Post-synthesis VHDL simulation (tool: Modelsim) [2.3]
4.1 Compilation of the VHDL/Verilog netlist and related testbench
4.2 Simulation of the post-synthesis gate-level netlist with timing data

Step 4) Placement and routing (tool: Cadence Encounter)
5.1 Generate a uniquified netlist (Convert Verilog mapped netlist) [??]
5.2 Design import (technological data + Verilog netlist) [4.3]
5.3 Floorplan specification [4.4]
5.4 Power ring/stripe creation and routing [4.6]
5.5 Global net connections definition [4.5]
5.6 Operating conditions definition [4.7]
5.7 Core cell placement [4.8]
5.8 Post-placement timing analysis [4.9]
5.9 Clock tree synthesis (optional) [4.10]
5.10 Design routing [4.12]
5.11 Post-route timing optimization and analysis [4.13]
5.12 Filler cell placement [4.11]
5.13 Design checks [4.14]
5.14 Report generation [4.15]
5.15 Post-route timing data extraction [4.16]
5.16 Post-route netlist generation [4.17]
5.17 GDS2 file generation [4.18]
Step 5) Post-layout VHDL/Verilog simulation (tool: Modelsim) [2.4]
6.1 Compilation of the Verilog netlist and related testbench
6.2 Simulation of the post-synthesis or post-P&R gate-level netlist with PaR timing data

Chapter 2
VHDL and Verilog simulation
This chapter presents the main steps to perform the logic simulation of VHDL and Verilog models with the
Modelsim tool.
2.1 Starting the Modelsim graphical environment
To start the Modelsim environment, create first a work library in de directory LIB/MSIM then enter in the
vsim command in the Unix shell:
student@tango-FILTER> vlib LIB/MSIM/work &
student@tango-FILTER> vsim &
Figure 2.1: Modelsim console window
The modelsim.ini file actually defines the mapping between logical design libraries and their physical
locations. Note that the Help menu on the top right allows one to access the complete documentation of
11

CHAPTER 2. VHDL AND VERILOG SIMULATION 12
the tool. After having started the vsim GUI you have to compile all the VHDL source of your design into
the simulation library work. Now you have two options to simulate your model, either interactively or by
executing the following convenience scripts (see directory SIM/BIN) on the VSIM command line:
wave.do To start a wave window with the ports of the top level module.
start_far[_mapped | _routed ].do To start up the simulation of the particular module.
run_far[_mapped | _routed ].do To load the filter coefficients into the coefficient ROM and runs the sim-
ulation for 300 us.
2.2 Simulation of (pre-synthesis) RTL VHDL models
The task here is to validate the functionality of the VHDL model that will be synthesized. The first step is
to compile the VHDL model and its associated testbench. There are two ways to compile VHDL models.
One way is to execute the vcom command from the command line of the Modelsim window:
ModelSim> vcom -quiet HDL/RTL/SYAA90_128X16X1CM2.vhd
ModelSim> vcom -quiet HDL/RTL/SPAA90_512X16BM1A.vhd
ModelSim> vcom -quiet HDL/RTL/coeffFAR.vhd
ModelSim> vcom -quiet HDL/RTL/dataRamFAR.vhd
ModelSim> vcom -quiet HDL/RTL/filter.vhd
ModelSim> vcom -quiet HDL/RTL/filter_top.vhd
ModelSim> vcom -quiet HDL/RTL/filter_soc.vhd
ModelSim> vcom -quiet -suppress 1288,1074,1194 HDL/TBENCH/filter_soc_tb.vhd
or alternatively execute the shell script compile_msim_far.sh from the CSH command line:
student@tango-FILTER> sh compile_msim_far.sh
The other way is to left-click on the Compile icon , to select the files to compile in the HDL/RTL
and HDL/TBENCH directories, click on Compile
and finally close the window (click Done). The
compiled modules are stored in the logical library
WORK which is mapped to the physical location
LIB/MSIM/work. Once VHDL (or Verilog) mod-
els have been successfully compiled in the design
library, it is possible to create a make file that can
be used to recompile only the required files. The
vmake command can only be run from a Unix shell
and creates the make file:
student@tango-FILTER> vmake > Makefile
The created file Makefile now defines the design unit dependencies and the compilation commands to
recompile only those source files that have been modified or that depend on modified files. To rebuild the
library, run the make command in the Unix shell
To simulate the RTL model, select the main menu
item Simulate ⇒ Start simulation... to get the sim-
ulation dialog window.
Select in the Design Tab from library work the archi-
tecture of the testbench and a resolution of ns. Then
click OK.

The main window now changes a bit to show the simulation hierarchy, the list of signals in the testbench
and the simulation console (with now the VSIM number> prompt).
Left clicking twice on an instance in the simulation hierarchy pane displays the corresponding VHDL source
in the right pane.
The next step is to select the signals to display in simulation.
Right click in the Objects (top center) pane, then select
Add to Wave ⇒ Signals in Region.
Note that the appropriate hierarchy level is selected in the simu-
lation hierarchy window. Selecting another level, e.g. dut, will
display all the signals visible in this scope. You may want to add
selected signals from inner levels (local signals).
The selected signals are displayed in a new window called wave.
The wave pane is by default located on the top right (as a new tab
on the source windows). You can click on the Undock icon
to make the wave pane separate.
Now first load the content coefficient file into the coefficient memory:
VSIM 7> run 35 ns
VSIM 7> do SIM/BIN/load.do
Then to start the simulation, it is either possible to enter run commands in the simulation console such as:
VSIM 7> run 300 us
or to click on the Run icon in the main window or in the wave window.
The signal waveforms are then visible in the wave window. To change the radix of the displayed signals,
select the signals (press shift left-click for multiple selection), then select the wave menu item
Format ⇒ Radix ⇒ Unsigned.

Note that the command run -all runs the simulation until there is no more pending event in the simulation
queue. This could lead to never ending simulation when the model, like the testbench loaded here, has a
continuously switching signal such as the clock signal clk. It is however possible to stop the current simu-
lation by clicking the Break icon in the main window or in the wave window.
Run the simulation interactively as described in the previous section or run the following scripts (See
SIM/BIN) from the VSIM command line.
VSIM 7> do SIM/BIN/start_far.do
VSIM 8> do SIM/BIN/wave.do
VSIM 9> do SIM/BIN/run_far.do
If you make any modiﬁcation to the VHDL source, you need to recompile the sources (manually or using the
vmake command described earlier in this section), and then restart the simulation in the same environment
(e.g., the same displayed waveforms or the same simulation breakpoints) with the restart -f command.
2.3 Simulation of the post-synthesis Verilog model with timing data
This step occurs after the RTL model has been synthesized into a gate-level netlist. The timing informa-
tion about the design which includes the delay of the library cells only is stored in a SDF ﬁle. (See -3.8
VHDL/Verilog gate-level netlist generation and post-synthesis timing data (SDF) extraction.)
Compile the Verilog gate-level netlist generated by the logic synthesis and its testbench in a new library
called mapped:
vlib LIB/MSIM/mapped
ModelSim> vcom -work LIB/MSIM/mapped HDL/RTL/SYAA90_128X16X1CM2.vhd
ModelSim> vcom -work LIB/MSIM/mapped HDL/RTL/SPAA90_512X16BM1A.vhd
ModelSim> vlog -work LIB/MSIM/mapped HDL/GATE/filter_soc_mapped.v
ModelSim> vcom -work LIB/MSIM/mapped HDL/TBENCH/filter_soc_tb_mapped.vhd
or execute the shell script compile_msim_far_mapped.sh.
To simulate the RTL model,
1. Select the main menu item Simulate ⇒ Start simulation... to get the simulation dialog window.
2. Select from library mapped the architecture of the testbench and a resolution of 100ps.
3. Click the Libraries tab to add the gate libraries fsd0a_a_generic_core and
fod0a_b25_t25_generic_io,

4. Then click the SDF tab. In the SDF dialog window, add the file SYN/TIM/filter_soc_mapped.sdf and
specify the region dut, which is the label of the instance in the testbench that will be annotated with
timing data. Note that the Reduce SDF errors to warnings box must be checked. This is required to
avoid the simulation to stop prematurely due to errors such as "Failed to find port á(7)´". These are
not really errors here as they are related to interconnect delay data in the SDF file that are not used in
the simulation (they are actually all set to zero).
Then click OK in the remaining Start Simulation dialog box to load the mapped netlist. Clock to output
delays of the order of 100ps to 1ns should be visible in the wave window.
Run the simulation interactively as described in the previous section or run the following scripts (See
SIM/BIN) from the VSIM command line.
VSIM 7> do SIM/BIN/start_far_mapped.do
VSIM 9> do SIM/BIN/run_far_mapped.do
2.4 Simulation of the post-route Verilog model with timing data
This step occurs after the design has been placed and routed. The Post-route SDF-file contains cell delay
and wire delays of the circuit. See "4.16 Post-route timing data extraction" and "4.17 Post-route netlist
generation". This step involves the simulation of a Verilog gate-level netlist with a VHDL testbench. Com-

pile the Verilog gate-level netlist generated by the logic synthesis and its testbench in a new library called
routed:
vlib LIB/MSIM/routed
ModelSim> vcom -work LIB/MSIM/routed HDL/RTL/SYAA90_128X16X1CM2.vhd
ModelSim> vcom -work LIB/MSIM/routed HDL/RTL/SPAA90_512X16BM1A.vhd
ModelSim> vlog -work LIB/MSIM/routed HDL/GATE/faraday-io.v
ModelSim> vlog -work LIB/MSIM/routed HDL/GATE/filter_soc-routed.v
ModelSim> vcom -work LIB/MSIM/routed HDL/TBENCH/filter_soc_tb_mapped.vhd
or execute the shell script compile_msim_far_routed.sh.
To simulate the placed and routed netlist with timing data:
1. Select the item Simulate ⇒ Start simulation... in the main menu to get the simulation dialog win-
dow.
2. Select from library routed the architecture of the testbench and a resolution of 100ps.
3. Then click the Libraries tab to add the gate libraries fsd0a_a_generic_core and
fod0a_b25_t25_generic_io
4. Load the SDF timing file PAR/TIM/filter_soc-routed.sdf.
Note that the Reduce SDF errors to warnings box must be checked. This is required to avoid the sim-
ulation to stop prematurely due to errors such as “Failed to find matching specify timing constraint”.
These are not really errors here as they are related to removal (asynchronous) timing constraints
generated by Encounter that are not supported in the Verilog models of the gates.
Run the simulation interactively or run the following scripts (See SIM/BIN) from the VSIM command line.
VSIM 7> do SIM/BIN/start_far_routed.do
VSIM 9> do SIM/BIN/run_far_routed.do

Chapter 3
Logic synthesis
This chapter presents the main steps to perform the logic synthesis of the VHDL RTL model with the
Synopsys Design Vision and Design Compiler tools. The sold alias displays the complete Synopsys doc-
umentation set. Manual pages are available by executing the command “snps man command” (e.g., snps
man design_vision).
3.1 Starting the Design Vision graphical environment
To start the Synopsys Design Vision environment, enter the design_vision command in a new shell:
student@tango-FILTER> design_vision
17

CHAPTER 3. LOGIC SYNTHESIS 18
The command line is also echoed in the terminal shell from which the tool has been started, so it is possible
to enter DC commands from there as well
(the shell has the design_vision> prompt). It is still possible to execute some Unix commands from here.
3.2 RTL VHDL model analysis
The analysis phase compiles the VHDL model and checks that
the VHDL code is synthesizable. Select File ⇒ Analyze... in
the main menu.
Use the Add... button to add all the VHDL sources you need to
analyze.
In the case you have more than one VHDL file to analyze, be
careful to list the files in the correct analysis order.
Click OK.
3.3 Design elaboration
The elaboration phase performs a generic pre-
synthesis of the analyzed model. It essen-
tially identifies the registers that will be in-
ferred.
Select File ⇒ Elaborate... in the main menu.
The DEFAULT library is identical to the WORK
library. Specify the value for the CWIDTH,
DWIDTH generic parameters to 16 and for the
CAW, DAW parameters 7.
Click OK.
The console now displays the inferred registers
and the kind of reset
(here asynchronous reset - AR: Y).
Listing 3.1: "Elaborate design command"
design_vision> elaborate FILTER_SOC -architecture RTL -library WORK
-parameters "CWIDTH = 16, CAW = 7, DWIDTH = 16, DAW = 7, CWIDTH = 16"
.
.
Inferred memory devices in process
in routine filter_DWIDTH16_DAW7 line 158 in file
’/mnt/tango/md2/users/sander/ET4351/asic/designs/filter1/HDL/RTL/filter.vhd’.
===============================================================================
| Register Name | Type | Width | Bus | MB | AR | AS | SR | SS | ST |
===============================================================================
| OutRegxDP_reg | Flip-flop | 16 | Y | N | Y | N | N | N | N |
===============================================================================
.
.
design_vision> Current design is ’filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7’.

Note the name filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7 given to the elaborated entity. It is
possible to display the elaborated schematic by selecting the entity i_filter_top in the hierarchy window
and then clicking the Create Design Schematic icon . Note that the symbols merely indicate generic
components that do not yet represent any real logic gate.
3.4 Design environment definition
Before a design can be optimized, you must define the environment in which the design is expected to
operate. You define the environment by specifying operating conditions, wire load models, and system
interface characteristics. Operating conditions include temperature, voltage, and process variations. Wire
load models estimate the effect of wire length on design performance. System interface characteristics
include input drives, input and output loads, and fanout loads. The environment model directly affects
design synthesis results. Here we will only deal with operating conditions and wire load models.
To define the operating conditions, select the main menu item:
Attributes ⇒ Operating Environment ⇒ Operating Conditions...
Select WCCOM condition, which defines a temperature of 125˚C, a voltage of 0.9V (the L90_SP process
is a 1V process), and a slow process. Each cell library defines its own set of operating conditions and may
use different names for each set.
Click OK.

Wire load models allow the tool to estimate the effect of wire length and fanout on the resistance, capaci-
tance, and area of nets. The FARADAY design kit defines a number of wire load models. It also defines an
automatic selection of the wire load model to use according to the design area, which is actually considered
here.
To get the definitions of the available operating conditions (and on the cell library), execute the report_lib
command in the tool command line:
report_lib fsd0a_a_generic_core_ss0p9v125c
The report_design command summarizes the definitions of the design environment.
3.5 Design constraint definitions
Many kinds of constraints may be defined on the design. Here only constraints on the area and the
clock will be defined. To define the clock attributes, i.e. its period and duty cycle, select the entity fil-
ter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7 in the hierarchy window and then click the
Create Symbol View icon.
In the symbol view, select the clk pin and then select the main menu item Attributes ⇒ Specify Clock....
Define a clock period of 10 ns with 50% duty cycle. Time unit is not specified here. It is defined in the cell
library and is usually ns.
Click OK. The console now includes the command line equivalent of the clock definition:
create_clock -name "clk" -period 10
-waveform { 0 5 } { clk }
To define an area constraint, select in the main menu the item
Attributes ⇒ Optimization Constraints ⇒ Design Constraints....
A max area constraint set to zero is not realistic but it will force the synthesizer to target a minimum area.
Click OK. The console now includes the command line equivalent of the constraint definition:
set_max_area 0

It is a now good idea to save the elaborated design so it
will be possible to run several optimization steps from that
point.
Select entity
filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7 in the
hierarchy window and then the main menu item
File ⇒ Save As....
Save the elaborated design under the name
filter_soc_elab.ddc in directory SYN/DB.
The selection of the option Save all design in hierarchy is
relevant for hierarchical designs.
The console includes the equivalent command line:
write -hierarchy -format ddc -output .../FILTER/SYN/DB/filter_soc_elab.ddc
To read back an elaborated design, select the main menu item File ⇒ Read... and then select the file to
read.

3.6 Design mapping and optimization
The optimization phase, also called here
compilation phase, is technology de-
pendent. It performs the assignment
of logic gates from the standard cell li-
brary to the elaborated design in such a
way the defined constraints are met.
Select the main menu item
Design ⇒ Compile Ultra....
For a first run there is no need to change
the default settings.
Click OK. The console and the Unix
shell now include the progress of the
work.
The equivalent command line is: compile_ultra -map_effort medium -area_effort medium
The mapped design schematic is now hierarchical as it includes instances of the coefficient rom, data ram
and the filter circuit. Also, the cells are now real gates from the cell library.
Note that the default resource allocation and implementation for operative parts is based on timing con-
straints.
This means that resource sharing is used so that timing constraints are met or not worsened. In our case, a

single adder has been inferred for both adder and subtractor operations.
The mapped design can now be saved. Select the entity filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7
in the hierarchy window and then the main menu item File ⇒ Save As.... Save the mapped design under
the name filter_soc_mapped.ddc in the directory SYN/DB.
3.7 Report generation
It is possible to get many reports on various synthesis results. Here only reports on the area used, critical
path timing and the resources used will be generated.
To get a report of the area used by the mapped design, select the main menu item Design > Report Area....
Save the report in the file
SYN/RPT/filter_soc_mapped_area.rpt as well as in the report viewer. Click OK.
A new window and the console now display the report:
Information: Updating graph... (UID -83)
****************************************
Report : area
Design : filter_soc
Version: D-2010.03-SP5 -1
Date : Wed May 30 13:52:10 2012
****************************************
Information: Updating design information... (UID -85)
Library(s) Used:
fsd0a_a_generic_core_ss0p9v125c (File: /opt/eds/DesignLab/tech/Faraday/L90_SP/Core/
fsd0a_a /2010Q4v2.1/GENERIC_CORE/FrontEnd/synopsys/synthesis/
fsd0a_a_generic_core_ss0p9v125c.db)
fod0a_b25_t25_generic_io_ss0p9v125c (File: /opt/eds/DesignLab/tech/Faraday/L90_SP/IO
/fod0a_b25 /2009Q2v3.0/ T25_GENERIC_IO/FrontEnd/synopsys/
fod0a_b25_t25_generic_io_ss0p9v125c.db)

SYAA90_128X16X1CM2_BC (File: /opt/eds/DesignLab/tech/Faraday/L90_SP/Memory/
SYAA90_128X16X1CM2_BC.db)
SPAA90_512X16BM1A_BC (File: /opt/eds/DesignLab/tech/Faraday/L90_SP/Memory/
SPAA90_512X16BM1A_BC.db)
Number of ports: 38
Number of nets: 78
Number of cells: 97
Number of references: 24
Combinational area: 176044.062891
Noncombinational area: 190436.095396
Net Interconnect area: undefined (Wire load has zero net area)
Total cell area: 366480.158287
Total area: undefined
1
The area unit depends on the standard cell library. Here all area figures are in square microns. The net
interconnect area is estimated with the use of a wire load model that has been automatically selected from
the design area.
To get a report on the most critical timing path in the mapped design, select the main menu item
Timing ⇒ Report Timing Path
Save the report in the file SYN/RPT/filter_soc_mapped_timing.rpt as well as in the report viewer.
Click OK. A new window and the console now display the report:

****************************************
Report : timing
-path full
-delay max
-max_paths 1
-sort_by group
Design : filter_soc
Version: D-2010.03-SP5 -1
Date : Wed May 30 13:52:13 2012
****************************************
Operating Conditions: WCCOM Library: fsd0a_a_generic_core_ss0p9v125c
Wire Load Model Mode: enclosed
Startpoint: i_filter_top/i_filter/StatexDP_reg [0]
(rising edge -triggered flip -flop clocked by ClkxCI)
Endpoint: DataInAckxSO
(output port clocked by ClkxCI)
Path Group: ClkxCI
Path Type: max
Des/Clust/Port Wire Load Model Library
------------------------------------------------
filter_soc G5K fsd0a_a_generic_core_ss0p9v125c
filter_DWIDTH16_DAW7 enG5K fsd0a_a_generic_core_ss0p9v125c
Point Incr Path
--------------------------------------------------------------------------
clock ClkxCI (rise edge) 0.00 0.00
clock network delay (ideal) 0.00 0.00
i_filter_top/i_filter/StatexDP_reg [0]/CK (DFFRBX1) 0.00 0.00 r
i_filter_top/i_filter/StatexDP_reg [0]/QB (DFFRBX1) 0.35 0.35 f
i_filter_top/i_filter/U178/O (NR2X1) 0.69 1.03 r
i_filter_top/i_filter/DataInAckxSO (filter_DWIDTH16_DAW7) 0.00 1.03 r
i_filter_top/DataInAckxSO (filter_top_CWIDTH16_CAW7_DWIDTH16_DAW7) 0.00 1.03 r
io_DataInAckxSO/x0/op/O (VYA4GSGB) 3.03 4.06 r
DataInAckxSO (out) 0.00 4.06 r
data arrival time 4.06
clock ClkxCI (rise edge) 8.00 8.00
clock network delay (ideal) 0.00 8.00
output external delay -0.80 7.20
data required time 7.20
--------------------------------------------------------------------------
data required time 7.20
data arrival time -4.06
--------------------------------------------------------------------------
slack (MET) 3.14
1
All times are expressed in ns (the time unit is defined in the cell library). The slack defines the time margin
from the clock period. A positive slack means that the latest arriving signal in the path still arrives before
the end of the clock period. A negative slack means that the timing constraint imposed by the clock is
violated.
The timing delays that are accounted for are the internal gate delays (from the cell library) and the estimated
interconnect delays (from the cell library and the wire load model in use).
To highlight the critical path on the schematic, select the filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7
entity in the hierarchy window and then the Select menu item

Schematic ⇒ New Path Schematic View ⇒ Of Paths From/Through/To... . You can see that the critical
path goes from pin DO(1) of instance .../i_filter_top/i_coeff/a9d16 to pin D of instance .../i_filter/OutRegxDP_reg[15].
Another useful report is the list of resources used. A resource is an arithmetic or comparison operator read
in as part of an HDL design. Resources can be shared during execution of the compile command.
To get a report on the resources used, select the main menu item Design ⇒ Report Design Resources....
SYN/RPT/filter_soc_mapped_resources.rpt as well as in the report viewer.
Click OK.
As the report stated no special operator were found in our filter_soc design.
The last useful report is the one on power used. Here a estimate on power consumption is given based on
switch activity and the library models used in the circuit.
To get a report on the power used, select the main menu item Design ⇒ Report Power....
SYN/RPT/filter_soc_mapped_power.rpt as well as in the report viewer.
Click OK.
A new window and the console now display the report:

Loading db f i l e ’/ opt / eds / DesignLab / tech / Faraday / L90_SP / IO / fod0a_b25 /2009 Q2v3 . 0 /
T25_GENERIC_IO / FrontEnd / synopsys / fod0a_b25_t25_generic_io_ss0p9v125c . db ’
Loading db f i l e ’/ opt / eds / DesignLab / tech / Faraday / L90_SP / Core / fsd0a_a /2010 Q4v2 . 1 /
GENERIC_CORE/ FrontEnd / synopsys / s y n t h e s i s / fsd0a_a_generic_core_ss0p9v125c . db ’
Loading db f i l e ’/ opt / eds / DesignLab / tech / Faraday / L90_SP / Memory / SPAA90_512X16BM1A_BC . db ’
Loading db f i l e ’/ opt / eds / DesignLab / tech / Faraday / L90_SP / Memory / SYAA90_128X16X1CM2_BC . db ’
I n f o r m a t i o n : Propagating s w i t c h i n g a c t i v i t y ( low e f f o r t zero delay s i m u l a t i o n ) . (PWR−6)
Warning : Design has unannotated primary i n p u t s . (PWR−414)
Warning : Design has unannotated s e q u e n t i a l c e l l o u t p u t s . (PWR−415)
Warning : Design has unannotated black box o u t p u t s . (PWR−428)
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
Report : power
−a n a l y s i s _ e f f o r t low
Design : f i l t e r _ s o c
Version : D−2010.03−SP5−1
Date : Wed May 30 13:52:13 2012
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
Libr ary ( s ) Used :
fsd0a_a_generic_core_ss0p9v125c ( F i l e : / opt / eds / DesignLab / tech / Faraday / L90_SP / Core /
fsd0a_a /2010 Q4v2 . 1 / GENERIC_CORE/ FrontEnd / synopsys / s y n t h e s i s /
fsd0a_a_generic_core_ss0p9v125c . db )
fod0a_b25_t25_generic_io_ss0p9v125c ( F i l e : / opt / eds / DesignLab / tech / Faraday / L90_SP / IO
/ fod0a_b25 /2009 Q2v3 . 0 / T25_GENERIC_IO / FrontEnd / synopsys /
fod0a_b25_t25_generic_io_ss0p9v125c . db )
SYAA90_128X16X1CM2_BC ( F i l e : / opt / eds / DesignLab / tech / Faraday / L90_SP / Memory /
SYAA90_128X16X1CM2_BC . db )
SPAA90_512X16BM1A_BC ( F i l e : / opt / eds / DesignLab / tech / Faraday / L90_SP / Memory /
SPAA90_512X16BM1A_BC . db )
Operating Conditions : WCCOM Lib rary : fsd0a_a_generic_core_ss0p9v125c
Wire Load Model Mode : enclosed
Design Wire Load Model Librar y
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
f i l t e r _ s o c G5K fsd0a_a_generic_core_ss0p9v125c
filter_top_CWIDTH16_CAW7_DWIDTH16_DAW7 enG30K fsd0a_a_generic_core_ss0p9v125c
f a r a d a y _ v c c c o p a d _ l i m i t 1 enG5K fsd0a_a_generic_core_ss0p9v125c
faraday_gndcopad_limit1 enG5K fsd0a_a_generic_core_ss0p9v125c
f a r a d a y _ v c c i o p a d _ l i m i t 1 _ 7 enG5K fsd0a_a_generic_core_ss0p9v125c
faraday_gndiopad_limit1_7 enG5K fsd0a_a_generic_core_ss0p9v125c
filter_DWIDTH16_DAW7 enG5K fsd0a_a_generic_core_ss0p9v125c
Global Operating Voltage = 0.9
Power−s p e c i f i c u n i t i n f o r m a t i o n :
Voltage Units = 1V
Capacitance Units = 1.000000 pf
Time Units = 1 ns
Dynamic Power Units = 1mW ( derived from V, C, T u n i t s )
Leakage Power Units = 1pW
Cell I n t e r n a l Power = 1.4108 mW (95%)
Net Switching Power = 79.1487 uW (5%)
−−−−−−−−−
Total Dynamic Power = 1.4899 mW (100%)

3.8 VHDL/Verilog gate-level netlist generation and post-synthesis tim-
ing data (SDF) extraction
This step generates a VHDL model of the mapped design for simulation and a Verilog model of the same
design to be used as input to the placement and routing tool. It also generates a SDF (Standard Delay
Format) file that includes the gate delays. Care should be taken to use the right naming scheme when
generating the SDF file, otherwise the back-annotation of the delays onto the VHDL or Verilog netlists for
simulation will fail. Here we only consider the back-annotation of VHDL netlists.
Before generating the VHDL netlist, it is required to apply some VHDL naming rules to the design. This is
done by entering the following command in the console (be sure that the entity filter_soc_CWIDTH16_CAW7_DWIDTH16_D
is selected in the hierarchy window):
change_names -hierarchy -rules vhdl -verbose
Save the mapped design in the file
filter_soc_mapped.vhd in the directory HDL/GATE.
Note: the dialog window creates HDL files with the .vhdl extension rather than .vhd as used so far.
Click Save. The console now echoes the equivalent command line:
write -hierarchy -format vhdl -output .../FILTER/HDL/GATE/filter_mapped.vhd
To generate the SDF file, enter the following command in the console
write_sdf -version 2.1 SYN/TIM/filter_soc_mapped.sdf
Information: Annotated ’cell’ delays are assumed to include load delay.
The informational message says that the estimated interconnect delays are actually included in the SDF file
as part of the cell delays. The generated SDF file actually includes a list of interconnect delays of zero
values.
Before generating the Verilog netlist, it is better to reload the database and apply specific Verilog naming
rules to the design. This is done by selecting File ⇒ Remove All Designs from the main menu, then reading
the database file ./SYN/DB/filter_soc_mapped.ddc, and entering the following command in the console
(be sure that the entity filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7 is selected in the hierarchy
window):
change_names -hierarchy -rules verilog -verbose
Save the mapped design in the file filter_soc_mapped.v in the directory HDL/GATE.
Click Save. The console now echoes the equivalent command line:
write -hierarchy -format verilog
-output .../FILTER/HDL/GATE/filter_soc_mapped.v

3.9 Design constraints generation for placement and routing
Both design environment and design constraint definitions may be stored in a format that can be read by
other Synopsys tools such as PrimeTime or other EDA tool such as Cadence Soc Encounter.
The following command creates a new file that includes the design constraints that have been defined for
synthesis in Tcl format:
write_sdc -nosplit SYN/SDC/filter_soc_mapped.sdc
It is important to do that step after the Verilog naming rules have been applied to the mapped design (see
3.8), otherwise there could be discrepencies on port/signal names between the netlist and the constraint file.
3.10 Design optimization with tighter constraints
It is possible to let the synthesizer infer another faster adder architecture, e.g., a carry look-ahead architec-
ture, by shortening the clock period. The goal here is to redo some steps in this chapter and to compare the
results with the ones obtained with the initially ¨slow¨clock.
1. Read the elaborated design. It is not necessary to re-analyze the VHDL sources.
2. Specifiy the clock with a 1 ns period.
3. Save the new elaborated entity in the file SYN/DB/filter_soc_CWIDTH16_CAW7_DWIDTH16_DAW7_1ns_elab.db.
4. Map and optimize the design.
5. Save the mapped design in the file SYN/DB/filter_soc_1ns_mapped.db.
6. Get the new area, timing and resources reports. Compare with the reports you got for the 10 ns clock
period.
7. Generate the VHDL gate-level netlist in
HDL/GATE/filter_soc_1ns_mapped.vhdl
and the associated SDF timing data file in
SYN/TIM/filter_soc_1ns_mapped.sdf.
8. Do a post-synthesis simulation.
9. Generate the Verilog gate-level netlist in HDL/GATE/filter_soc_1ns_mapped.v.
10. Save the design constraints for placement and routing in the file
SYN/SDC/filter_soc_1ns_mapped.sdc

3.11 Using scripts
It is much more convenient to use scripts and to run the synthesis tool in batch mode when the design
complexity increases. Scripts also conveniently capture the synthesis flow and make it reusable. Synopsys
Design Compiler supports the Tcl language for building scripts.
An example of such a script for the synthesis of the filter_soc design has been installed in the SYN/BIN
directory (see “1.3 VHDL example: FIR-Filter”). The script must be run from the project top directory and
it assumed a directory organization as described in “1.2 Design project organisation”. To run the Tcl script,
execute the following command in a Unix shell:
student@tango-FILTER> dc_shell -f SYN/BIN/filter_soc_syn.tcl
When the script finishes executing, the dc_shell environment is still active so you can enter other dc_shell
commands. Enter quit or exit to return to the Unix shell.
The script is given below. It may be modified to define design information and constraints and to control
the flow to some extent.

Chapter 4
Standard cell placement and routing
This chapter presents the main steps to perform the placement and the routing of the synthesized gate-
level netlist using standard cells from the FARADAY design kit. The tool used here is Cadence Encounter
(Velocity).
4.1 Starting the Encounter graphical environment
To start the Encounter environment, enter the velocity command in a new Unix shell:
student@tango-FILTER> velocity -log PAR/LOG/encounter -overwrite
31

CHAPTER 4. STANDARD CELL PLACEMENT AND ROUTING 32
that includes all commands entered in the session. If the -overwrite switch is not used, both log and com-
mand files are incremented at each new session. The Unix shell from which the tool is started is called the
Encounter console. The console displays the velocity> prompt. This is where you can enter all Encounter
text commands and where the tool displays messages. If you use the console for other actions, e.g., Unix
commands, the Encounter session suspends until you finish the action.
The main window includes three different design views that you can toggle
during a session: the Floorplan view, the Amoeba view, and the Physical view.
The Floorplan view displays the hierarchical module and block guides, con-
nection flight lines, and floorplan objects, including block placement, and power/ground nets. The Amoeba
view displays the outline of the modules and submodules after placement, showing physical locality of the
module. The Physical view displays the detailed placements of the module’s blocks, standard cells, nets,
and interconnects.
The main window includes a satellite window, which identifies the location of the current view in the design
display area, relative to the entire design. The chip area is identified by a yellow box, the satellite view is
identified by the pink crossbox. When you display an entire chip in the design display area, the satellite
crossbox encompasses the chip area yellow box.
When you zoom and pan through the chip in the design display area, the satellite crossbox identifies where
you are relative to the entire chip.
• To move to an area in the design display area, click and drag on the satellite crossbox.
• To select a new area in the design display area, click and drag on the satellite crossbox.
• To resize an area in the satellite window, click with the Shift key and drag a corner of the crossbox.
• To define a chip area in the satellite window, right-click and drag on an area.
There are a number of binding keys available (hit the key when the Encounter GUI is active):
b display the list of binding keys
d (de)select or delete objects
f zoom the display to fit the core area
k create a ruler
K remove last ruler displayed
q display the object attribute editor form for the selected object; click the left-button mouse to select an
object, Shift-click to select or deselect an object
u undo last command
U redo last command
z zoom-in 2x
Z zoom-out 2x
Arrows pan the display.
Hit CTRL-R to refresh the display.

4.2 Generate uniquified netlist
Within your synthesized netlist, there are several instances of the same modules. You might realize that
these modules should have unique names and currently they do not. You will fix this using an Encounter
command to make the instances unique:
student@tango-FILTER> uniquifyNetlist
4.3 Design import
Importing the design into Encounter involves specifying the following setup information:
Design libraries and files. This includes informa-
tion on the technological process and the cell li-
brary in the LEF (Layout Exchange Format) for-
mat. LEF files provides information such as metal
and via layers and via generate rules which is used
for routing tasks. They also provide the minimum
information on cell layouts for placement and rout-
ing.
Gate-level netlist. This relates to the (Verilog)
netlist to be placed and routed.
Timing libraries. This includes information on the
cell timings (delays, setup/hold times, etc.).
To start the design import, select File ⇒ Import
Design... in the main menu. Then, click on
the Load... button and load the file PAR/CON-
F/L90_SP_std.conf
This file defines a basic import configuration.
There is a number of additions and changes to bring to the initial configuration. The new configuration will
then be saved for future uses.
The first information to add is the netlist. Click on the ... button on the right of the Verilog Files field. You
get a new dialog window with only one pane. Click on the top-right icon to get the full window. Remove
the VERILOG/none line in the left pane.
Select the Verilog netlist file HDL/GATE/filter_soc_unique.v (or the Verilog netlist you want to place and
route), add it to the left pane and close the window. It is assumed here that the imported netlist is the one
generated for the 8 ns clock period.
In the Design Import window, select the Auto Assign box to let the tool extract the top cell name from the
file. If the Verilog file includes more than one design (more than one top module name), you need to give
the name of the top module to use explicitly.
In the Timing Constraint File Field:
Select the file that has been generated during logic synthesis (3.6 Design mapping and optimization):
SYN/SDC/filter_soc_mapped.sdc Only timing information in the constraint file is actually used by En-
counter.
In the IO Assignment File Field:
Select the PAR/CONF/filter_soc.io file
In the Advanced tab select in the left pane the Power tag, you can keep only the VCC and GND power
nets. The names of power and ground nets must be the same as the ones used in the LEF file that describes
the standard cells.
You can now save the updated configuration in the file

PAR/CONF/filter_soc.conf by clicking on the Save... button.
Finally, click on OK. The configuration is then read in.
To reload a configuration, select File ⇒ Import Design... in the main menu. Then, click on the Load...
button and load the configuration file from the PAR/CONF directory.
4.4 Floorplan Specification
The floorplan defines the actual form, or aspect ratio, the layout will take, the global and detailed routing
grids, the rows to host the core cells and the I/O pad cells (if required), and the location of the corner cells
(if required).
Select Floorplan ⇒ Specify Floorplan... in the main menu.
In order to be able to add PAD cells and IO cells we need to specify Die Size and the Core to IO Boundary
parameters. Click the button at Die Size by: and fill in 1872.02 µm for both Width and Height.
At "Core Margins by:" click the button Core to IO Boundary and fill in the distance between the I/O
boundary and the core, here 560iµm at Core to Left, Top, Right, Bottom. Click OK.
If you want to change the coordinates you will need the metrics of the core , IO and pad cells. These metrics
are described in Appendix D.
Select Floorplan ⇒ Automatic Floorplan ⇒ Plan Design... in the main menu to execute the floorplan-
ning. The memory macro’s are placed into the core area. You can move the memory cells if the initial
placement does not suit you.
Additionally, the command Floorplan ⇒ Clear Floorplan... allows you to delete all or parts of the floor-
plan objects.
With Floorplan ⇒ Automatic Floorplan ⇒ Finish Floorplan... halo’s around the macro cell can be
specified to prevent placement of standardcells to close to the macro cells. Specify here a halo width of 28
um and leave everything else default.
Now the gaps between the IO cells must be filled with IO-filler cells.
Execute the fillperi.tcl script by the following command on the command line:
velocity> source PAR/BIN/fillperi.tcl
The display design area pane now shows the defined floorplan with the required number of rows.
It is a good idea to save the design at that stage to allow restarting here quickly without needing to redo all
the previous steps.

Select File ⇒ Save Design... in the main menu and save the current state in the file
PAR/DB/filter_soc-fplan.enc.
The data are actually saved in the directory PAR/DB/filter_soc-fplan.enc.dat.
To restore design data, select File ⇒ Restore Design... in the main menu and select the .enc file to read in
the PAR/DB directory.
4.5 Global net connections
This step assigns pins or nets to global power and ground nets. The imported Verilog netlist does not
mention any power and ground connections. However, the cells that will be placed do have power/ground
pins that will need to be routed to the global power/ground nets defined for the block.
Select Floorplan ⇒ Connect Global Nets... in the main menu.
The left pane (Connection List) is initially empty. For each VCC and ground net:
Check the Pins field and enter the pin name (VCC or GND).

Fill the To Global Net field with either VCC or GND.
Click on Add to List. The left pane now includes the related global net connection.
Repeat these actions with Tie High checked and finally with Tie Low checked.
Click on Apply and then on Close.
4.6 Power ring/stripe creation and routing
This step generates the VCC and GND power rings around the core and optionally adds a number of vertical
and/or horizontal power stripes across the core. Stripes ensure a proper power distribution in large cores.
They are not strictly required here as the design is small.
Select Power ⇒ Power Planning ⇒ Add Rings... in the main menu.
The Net(s) field defines the number and the kinds of rings from the core. In our case, there will be first a
ground ring around the core and a VCC ring around the ground ring. The net names should be consistent
with the power net names in the cell LEF file.
In the Ring Type field check Core ring(s) contouring. The Ring Configuration field should define ring
widths of 2.8 micron spaced by 1.12 micron.
The rings will be placed either in the center of the channel between the core and the chip boundary (or the
IO pads, if any) or at a particular offset from the core . Check the Specify in the Ring Configuration field
and specify an offset to the core of 28 µm.
It is possible to extend the ring segments to reach the core boundary.
Click on the Advanced tab and click on the segments you’d like to extend.
Other power and ground side trunks can be defined by selecting only horizontal or vertical segments.
Click OK to generate the rings.
To add block rings around the memory blocks, select Power ⇒ Power Planning ⇒ Add Rings... in the
main menu.

In the Ring Type field check Block ring(s) around. The Ring Configuration field should define ring widths
of 1.12 micron spaced by 0.56 micron. Check the Specify in the Ring Configuration field and specify an
offset to the block of 5.6 µm.
Click OK to generate the block rings.
It is possible to measure sizes by using the ruler (or hit the k binding key). Hit K to remove the last
ruler or press ESC to remove all rulers.
To remove ring segments select them and hit the Delete key.
To add power stripes, select Power ⇒ Power Planning ⇒ Add Stripes... in the main menu.
The Set Configuration area defines the Net(s) pattern, direction, layer, width and spacing of the stripes.
Our example does not need any stripes so click Cancel

Now, it is possible to route the power grid. Select Route ⇒ SRoute... in the main menu. All default values
are fine. Click OK to do the routing. The design now looks like below:
It is recommended to save the new stage of the design. Select File ⇒ Save Design... in the main menu and
save the current state in the file PAR/DB/filter_soc-pplan.enc.
4.7 Operating conditions definition
The operating conditions define the temperature, process and voltage conditions for the design. They impact
the timing calculations and optimizations.
Select the Options ⇒ Set Mode ⇒ Specify Operating Condition/PVT... in the main menu.
In the max tab, select the WCCOM operating condition for Timing Library: fsd0a_a_generic_core_ss0p9v125c.
In the min tab, select the BCCOM operating condition for Timing Library: fsd0a_a_generic_core_ff1p1vm40c.
Click OK.
The max operating conditions will be used to meet setup timing constraints, while the min operating condi-
tions will be used to meet hold timing constraints.
The Encounter console summarizes the settings:

Set Min operating condition to ’fsd0a_a_generic_core_ff1p1vm40c/%NOM_PVT’ defined in
Timing Library ’fsd0a_a_generic_core_ff1p1vm40c’
Process: 1.00 Temperature: -40.000 Voltage: 1.100
Set Max operating condition to ’fsd0a_a_generic_core_ss0p9v125c/%NOM_PVT’ defined in
Timing Library ’fsd0a_a_generic_core_ss0p9v125c’
Process: 1.00 Temperature: 125.000 Voltage: 0.900
*** Calculating scaling factor for min libraries using operating condition:
Name: fsd0a_a_generic_core_ff1p1vm40c/%NOM_PVT Process: 1.00 Temperature:
-40.000 Voltage: 1.100
*** Calculating scaling factor for max libraries using operating condition:
Name: fsd0a_a_generic_core_ss0p9v125c/%NOM_PVT Process: 1.00 Temperature:
125.000 Voltage: 0.900
Running the following command in the Encounter console gives the active operating conditions:
velocity 1> getOpCond -v
min: fsd0a_a_generic_core_ff1p1vm40c/%NOM_PVT proc: 1.0000 volt: 1.1000 temp:
-40.0000
max: fsd0a_a_generic_core_ss0p9v125c/%NOM_PVT proc: 1.0000 volt: 0.9000 temp:
125.0000
4.8 Core cell placement
This step places the cells of the imported Verilog netlist in the rows.
Select Place ⇒ Standard Cells... in the main menu.
By clicking the Mode button one can specify placement options. By default it will run in Timing Driven
Placement Mode. Stick to the default options and click OK.
The Timing Driven Placement Mode option will optimize the placement of the cells that are on the critical
path. Some cell instances may be replaced with cells having lower driving capabilities (downsizing) or
stronger driving capabilities (upsizing). Buffers may be also added or deleted. The Velocity console notifies
such changes.
Click OK to do the placement. It may take some time to complete, especially when the placement is timing
driven and a high effort level is used .
The placement should then look like below:
save the current state in the file PAR/DB/filter_soc-placed.enc.

4.9 Post-placement timing analysis
The timing analysis engine in Encounter can now be run to get a relatively good idea of the timing perfor-
mances of the design. It actually performs a trial routing and a parasitic extraction based on the current cell
placement.
Select Timing ⇒ Report Timing... in the main menu. Deﬁne the path for the slack report ﬁle. Click OK.
In the Encounter console window you get a summary of the timing analysis:
###############################################################
# Generated by: Cadence Encounter 09 .12−s159_1
# OS: Linux i686 ( Host ID s a l s a )
# Generated on: Wed May 30 11 :14:18 2012
# Command: timeDesign −preCTS −idealClock −pathReports − d r v R e p o r t . . .
###############################################################
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
timeDesign Summary
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
+−−−−−−−−−−−−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+
| Setup mode | a l l | reg2reg | in2reg | reg2out | in2out | c l k g a t e |
+−−−−−−−−−−−−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+
| WNS ( ns ) : | 2 .082 | 3 .385 | 5 .841 | 2 .082 | N/A | N/A |
| TNS ( ns ) : | 0 .000 | 0 .000 | 0 .000 | 0 .000 | N/A | N/A |
| V i o l a t i n g P a t h s : | 0 | 0 | 0 | 0 | N/A | N/A |
| All P a t h s : | 200 | 102 | 98 | 18 | N/A | N/A |
+−−−−−−−−−−−−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+−−−−−−−−−+
+−−−−−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−+
| | Real | Total |
| DRVs +−−−−−−−−−−−−−−−−−−+−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−|
| | Nr n e t s ( terms ) | Worst Vio | Nr n e t s ( terms ) |

+−−−−−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−+−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−+
| max_cap | 2 ( 2 ) | −0.081 | 2 ( 2 ) |
| max_tran | 4 (134) | −0.567 | 4 (134) |
| max_fanout | 0 ( 0 ) | 0 | 0 ( 0 ) |
+−−−−−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−+−−−−−−−−−−−−+−−−−−−−−−−−−−−−−−−+
D e n s i t y : 10 .698%
Routing Overflow: 0 .00% H and 0 .00% V
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
The design is not critical as the slack is positive (2.082 ns).
To get more details on the critical path execute the following commands in the Encounter console:
velocity 16> report_timing
The following report is then displayed in the console:
###############################################################
# Generated by: Cadence Encounter 09 .12−s159_1
# OS: Linux i686 ( Host ID s a l s a )
# Generated on: Wed May 30 11 :24:59 2012
# Command: r e p o r t _ t i m i n g
###############################################################
Path 1 : MET Late E x t e r n a l Delay A s s e r t i o n
Endpoint: DataInAckxSO ( ^ ) checked with l e a d i n g
edge of ’ ClkxCI ’
B e g i n p o i n t : i _ f i l t e r _ t o p / i _ f i l t e r / StatexDP_reg_0_ /QB ( v ) t r i g g e r e d by l e a d i n g
edge of ’ ClkxCI ’
Other End A r r i v a l Time 0 .000
− E x t e r n a l Delay 0 .800
+ Phase S h i f t 8 .000
= Required Time 7 .200
− A r r i v a l Time 5 .118
= Slack Time 2 .082
Clock Rise Edge 0 .000
+ Clock Network Latency ( I d e a l ) 0 .000
= Beginpoint A r r i v a l Time 0 .000
+−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−+
| I n s t a n c e | Arc | Cell | Delay | A r r i v a l | Required |
| | | | | Time | Time |
|−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−+−−−−−−−−−−−−−−−−+−−−−−−−−−−+−−−−−−−+−−−−−−−−−+−−−−−−−−−−|
| i _ f i l t e r _ t o p / i _ f i l t e r / StatexDP_reg_0_ | CK ^ | | | 0 .000 | 2 .082 |
| i _ f i l t e r _ t o p / i _ f i l t e r / StatexDP_reg_0_ | CK ^ −> QB v | DFFRBX1 | 0 .331 | 0 .331 | 2 .413 |
| i _ f i l t e r _ t o p / i _ f i l t e r / U178 | I2 v −> O ^ | NR2X1 | 1 .383 | 1 .713 | 3 .795 |
| io_DataInAckxSO_x0_op | I ^ −> O ^ | VYA4GSGB | 3 .405 | 5 .118 | 7 .200 |
| | DataInAckxSO ^ | | 0 .000 | 5 .118 | 7 .200 |

+−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−+
If timing requirements are not met optimization is possible by selecting Optimize ⇒ Optimize Design...
in the main menu and check pre-CTS and click OK.
4.10 Clock tree synthesis (optional)
As the paths that will propagate the clock signal in the design are not necessarily balanced, some registers
may receive the active clock edge later than others (clock skew) and may therefore violate the assumed
synchronous design operation. For example, the original clock tree we can get from the previously placed
design is shown below.
To create a balanced clock tree, you have first to create a clock tree specification file. Encounter can create a
first draft version of the file you can then edit to include design specific data. Here we will use a ready made
specification file PAR/CTS/filter_soc-spec.ctstch Select Clock ⇒ Synthesize Clock Tree... in the main
menu. In the popup menu change the Results Directory to PAR/CTS/clock_report at Clock Specification
Files: on the ... button to add the clock specification file PAR/CTS/filter_soc-spec.ctstch .
Click OK to create the clock tree.
To display the generated clock tree, select
Clock ⇒ Display ⇒ Display Clock Tree ... in the main menu.
The clock paths have been balanced according to the clock tree specifications.
To get a report on the clock tree synthesis, enter the following command at the velocity prompt.
velocity 1> reportClockTree -report PAR/RPT/filter_soc.ctsrpt
The following report is also displayed in the Encounter console:
velocity 10> reportClockTree
Redoing specifyClockTree ...
Checking spec file integrity...
reportClockTree Option :
*** Look For Reconvergent Clock Component ***
The clock tree io_ClkxCI_x0_ip/O has no reconvergent cell.
#
# Mode : Setup
# Library Name : fsd0a_a_generic_core_ss0p9v125c
********** Clock io_ClkxCI_x0_ip/O Pre-Route Timing Analysis **********
Nr. of Subtrees : 1
Nr. of Sinks : 66
Nr. of Buffer : 1
Nr. of Level (including gates) : 1
Root Rise Input Tran : 0.1(ps)
Root Fall Input Tran : 0.1(ps)
Max trig. edge delay at sink(R): i_filter_top/i_filter/AccuxDP_reg_15_/CK 385.4(ps)
Min trig. edge delay at sink(R): i_filter_top/i_filter/OutRegxDP_reg_1_/CK 364.5(ps)

(Actual) (Required)
Rise Phase Delay : 364.5~385.4(ps) 0~8000(ps)
Fall Phase Delay : 302.1~323(ps) 0~8000(ps)
Trig. Edge Skew : 20.9(ps) 300(ps)
Rise Skew : 20.9(ps)
Fall Skew : 20.9(ps)
Max. Rise Buffer Tran. : 182.5(ps) 400(ps)
Max. Fall Buffer Tran. : 156.6(ps) 400(ps)
Max. Rise Sink Tran. : 170.2(ps) 400(ps)
Max. Fall Sink Tran. : 76.4(ps) 400(ps)
Min. Rise Buffer Tran. : 182.5(ps) 0(ps)
Min. Fall Buffer Tran. : 156.6(ps) 0(ps)
Min. Rise Sink Tran. : 170.2(ps) 0(ps)
Min. Fall Sink Tran. : 76.2(ps) 0(ps)
Generating Clock Analysis Report filter_soc.ctsrpt ....
Clock Analysis (CPU Time 0:00:00.0)
*** End reportClockTree (cpu=0:00:00.0, real=0:00:00.0, mem=476.0M) ***
Several clock report files are also available in the PAR/CTS/clock_report directory.
save the current state in the file PAR/DB/filter_soc-cts.enc.

4.11 Filler cell placement
Filler cells will fill remaining holes in the rows and ensure the continuity of power/ground rails and N+/P+
wells in the rows. To fill the holes with filler cells, select Place ⇒ Physical Cell ⇒ Add Filler... in the
main menu.
Select the cells FILLER64E, FILLER32E, FILLER16E, FILLER8E, FILLER4E, FILLER3, FILLER2 and
FILLER1 and click OK to place the filler cells.
Another way to add the filler cells is by executing the tcl script "fillcore.tcl":
velocity 1> source PAR/BIN/fillcore.tcl
4.12 Design routing
This step generates all the wires required to connect the cells according to the imported gate-level netlist.
To route the design, select
Route ⇒ Nanoroute... in the main menu, check the Timing Driven box and a maximum effort.
Click OK to do the routing.
You now get the routed design:

save the current state in the file PAR/DB/filter_soc-routed.enc.
4.13 Post-routing timing optimization and analysis
A final timing optimization may be done on the routed design. Select
Optimize ⇒ Optimize Design... in the main menu. Select the postRoute box.
Click OK.
The results of the optimization is displayed in the Encounter console:
4.14 Design checks
The Verify menu has a number of items to check that the design has been properly placed and routed.
Select Verify ⇒ Verify Connectivity... in the main menu. Define the report file as PAR/RPT/filter_soc-
conn.rpt.
Click OK.
The console displays the results:
******** Start: VERIFY CONNECTIVITY ********

Start Time: Wed May 30 12:49:45 2012
Design Name: filter_soc
Database Units: 1000
Design Boundary: (0.0000, 0.0000) (1872 .0800, 1872.0800)
Error Limit = 1000; Warning Limit = 50
Check all nets
VC Elapsed Time: 0:00:00.0
Begin Summary
Found no problems or warnings.
End Summary
End Time: Wed May 30 12:49:45 2012
******** End: VERIFY CONNECTIVITY ********
Verification Complete : 0 Viols. 0 Wrngs.
(CPU Time: 0:00:00.1 MEM: 0.008M)
Select Verify ⇒ Verify Geometry... in the main menu. In the Advanced tab, define the report file as
PAR/RPT/filter_soc-geom.rpt.
Click OK.

The console displays the results:
VERIFY GEOMETRY ...... Sub-Area : 15 complete 0 Viols. 0 Wrngs.
VERIFY GEOMETRY ...... SubArea : 16 of 16
VERIFY GEOMETRY ...... Cells : 0 Viols.
VERIFY GEOMETRY ...... SameNet : 0 Viols.
VERIFY GEOMETRY ...... Wiring : 0 Viols.
VERIFY GEOMETRY ...... Antenna : 0 Viols.
VERIFY GEOMETRY ...... Sub-Area : 16 complete 0 Viols. 0 Wrngs.
VG: elapsed time: 5.00
Begin Summary ...
Cells : 0
SameNet : 0
Wiring : 0
Antenna : 0
Short : 0
Overlap : 0
End Summary
Verification Complete : 0 Viols. 0 Wrngs.
**********End: VERIFY GEOMETRY**********
*** verify geometry (CPU: 0:00:04.4 MEM: 3.8M)
4.15 Report generation
A number of reports have been already generated in the previous steps. They should be located in the
PAR/RPT directory. The Tools menu includes some additional reports:
File ⇒ Report⇒ Netlist Statistics gives the following output in the console:
velocity 15> *** Statistics for net list filter_soc ***
Number of cells = 2949
Number of nets = 689

Number of tri-nets = 18
Number of degen nets = 0
Number of pins = 2411
Number of i/os = 38
Number of nets with 2 terms = 419 (60.8%)
Number of nets with >=10 terms = 37 (5.4%)
*** 69 Primitives used:
Primitive PAD9M126G (56 insts)
Primitive VCCKGB (1 insts)
Primitive GNDKGB (1 insts)
Primitive VCC2IOGB (8 insts)
Primitive GND2IOGB (8 insts)
Primitive SPAA90_512X16BM1A (1 insts)
Primitive UYNGB (20 insts)
Primitive VYA4GSGB (18 insts)
Primitive SYAA90_128X16X1CM2 (1 insts)
Primitive EMPTY8GB (32 insts)
Primitive CORNERGB (4 insts)
Primitive XOR3X1 (4 insts)
Primitive XOR2CKX1 (1 insts)
Primitive TIE1X1 (2 insts)
Primitive TIE0X1 (2 insts)
Primitive QDFERBX1 (22 insts)
Primitive OR2X1 (1 insts)
Primitive OAI22XLP (1 insts)
Primitive OAI12X1 (15 insts)
Primitive OA12XLP (2 insts)

File ⇒ Report ⇒ Gate Count... gives the following output in the console:
velocity 15> Gate area 2.3520 um^2
[0] filter_soc Gates=16332 Cells=504 Area=38414.3 um^2
[1] i_filter_top Gates=16314 Cells=497 Area=38371.1 um^2
[2] i_filter_top/i_filter Gates=1855 Cells=493 Area=4363.7 um^2
[2] i_filter_top/i_coeff_a9d16 Gates=6995 Cells=0 Area=16453.7 um^2
[2] i_filter_top/i_dataRAM_i_dmem Gates=7461 Cells=0 Area=17549.0 um^2
Finally, File ⇒ Report ⇒ Summary... displays the following window:
*** Statistics for net list filter_soc ***
Number of cells = 2949
Number of nets = 689
Number of tri-nets = 18
Number of degen nets = 0
Number of pins = 2411
Number of i/os = 38
Number of nets with >=10 terms = 37 (5.4%)
*** 69 Primitives used:
Primitive PAD9M126G (56 insts)

Primitive VCCKGB (1 insts)
Primitive GNDKGB (1 insts)
Primitive VCC2IOGB (8 insts)
Primitive GND2IOGB (8 insts)
Primitive SPAA90_512X16BM1A (1 insts)
Primitive UYNGB (20 insts)
Primitive VYA4GSGB (18 insts)
Primitive SYAA90_128X16X1CM2 (1 insts)
Primitive CORNERGB (4 insts)
Primitive XOR2CKX1 (1 insts)

4.16 Post-route timing data extraction
This step generates the post-route SDF file that includes both the actual interconnect and cell timing delays.
The parasitics must be first extracted. Therefore set the extraction mode:
Select Options ⇒ Set Mode ⇒ Specify RC Extraction Mode... in the main menu.
Check PostRoute, EffortLevel: Low, Extraction Type: Coupled RC
And extract the netlist:
Select Timing ⇒ Extract RC... in the main menu.
The generated Cap file includes the wired capacitance, pin capacitance, total capacitance, net length, wire
cap per unit length and the fanout of each net in the design. The generated SPEF (Standard Parasitics
Exchange Format) file includes RC values in a SPICE-like format.
The SDF file may be then generated by selecting
Timing ⇒ Write SDF... in the main menu. The checked Ideal Clock switch means that flip-flops are
considered as having 0ps rising and falling transition times.

4.17 Post-route netlist generation
This steps generates a Verilog netlist of the routed design. The netlist may be different from the imported
netlist as cells may have been added or replaced during clock tree synthesis and timing-driven optimizations.
Select File ⇒ Save ⇒ Netlist... in the main menu. Do not select Include Leaf Cell Definition as they are
provided in a separate library.
The generated file should go into the HDL/GATE directory.
4.18 GDS2 file generation
The placed and routed design can be exported in different formats for further processing outside the En-

counter tool. The GDS2 binary format is a standard format for integrating the block in the top-level layout,
doing DRC/LVS checkings, or delivering the layout to the foundry. To export the design in the GDS2 for-
mat, select File ⇒ Save ⇒ GDS/OASIS... in the main menu. The GDS map file has been copied by the
tech_setup script into the PAR/DEX directory. The generated GDS2 file is written in the same directory.
-
4.19 Using scripts
As for the synthesis step, it is much more convenient to capture the placement and routing flow in a script.
Cadence Encounter also support sthe Tcl language for building scripts.
An example of such a script for placement and routing of the Fir-Filter design has been installed in the
PAR/BIN directory (see “?? VHDL example: FIR-Filter”). The script must be run from the project top
directory and it assumes a directory organization as described in “1.2 Design project organisation”. To run
the Tcl script, execute the following command in a Unix shell:
velocity -log PAR/LOG/encounter -overwrite -init PAR/BIN/top-level.tcl -win
The script top-level.tcl given below calls TCL subscripts, one for each design step. During an interactive
session of Encounter you can source the scriptsi the proper sequence at the velocity command prompt. This
allows for checking the result after each Place&Route step. By modifying parameters in a particular design
step script you can define design information and to control the flow to some extent.
Note that a configuration file must exist before running the script. The configuration file name is in the
PAR/CONF directory and its name is defined in the script.
The script does a bit more than the steps described earlier. For example, it uses an I/O pin placement
definition as provided by a PAR/CONF/filter_soc.io file.
set PROJECT_DIR [pwd]
set PAR_BIN ${PROJECT_DIR}/PAR/BIN
# Import the design
source ${PAR_BIN}/start.tcl
# Create a floorplan
source ${PAR_BIN}/fplan.tcl
# Create power/ground distribution lines
source ${PAR_BIN}/pplan.tcl
# Place standard cells into the core
source ${PAR_BIN}/place.tcl
# Create the Clock Tree
source ${PAR_BIN}/cts.tcl
# Place Filler Cells and route the design
source ${PAR_BIN}/route.tcl
# Verify Connectivity and Geometry
source ${PAR_BIN}/verify.tcl
# Extract the circuit
source ${PAR_BIN}/results.tcl

Appendix A
Appendix A: VHDL Netlists
A.1 File: ﬁlter.vhd
Listing A.1: RTL synthesisable model of a 128 tap FIR-Filter.
library ieee;
entity filter is
generic (
CAW : integer := 7;
DAW : integer := 7
);
port (
DataOutAckxSI : in std_logic;
LutAddrxDO : out std_logic_vector(CAW -1 downto 0);
LutReadxDI : in std_logic_vector(CWIDTH -1 downto 0);
RamWriteEnxSO : out std_logic;
RamAddrxDO : out std_logic_vector(DAW -1 downto 0);
RamReadxDI : in std_logic_vector(DWIDTH -1 downto 0);
RamWritexDO : out std_logic_vector(DWIDTH -1 downto 0)
);
end filter;
architecture rtl of filter is
------------------------------------------------------------
-- component declarations
------------------------------------------------------------
-- State
type state_type is (idle , new_data , run , data_out);
signal StatexDP , StatexDN : state_type;
-- Registers
signal RamWriteEnxS : std_logic;
56

APPENDIX A. APPENDIX A: VHDL NETLISTS 57
signal InRegEnxS : std_logic;
signal InRegxDN : std_logic_vector(DWIDTH -1 downto 0);
-- Counters
signal OffsetDecxS : std_logic;
signal OffsetxDP , OffsetxDN : unsigned(DAW -1 downto 0);
signal CounterIncxS : std_logic;
signal CounterxDP , CounterxDN : unsigned(CAW -1 downto 0);
-- Counters
signal RamAddrxD : std_logic_vector(DAW -1 downto 0);
signal LutAddrxD : std_logic_vector(CAW -1 downto 0);
-- ALU signals
signal SumxD : signed((DWIDTH+CWIDTH)-1 downto 0);
signal SumStdxD : std_logic_vector((DWIDTH+CWIDTH)-1 downto 0);
signal RamReadxD : std_logic_vector(DWIDTH -1 downto 0);
signal RamSignedxD : signed(DWIDTH -1 downto 0);
signal LutReadxD : std_logic_vector(CWIDTH -1 downto 0);
signal LutSignedxD : signed(CWIDTH -1 downto 0);
signal MultxD : signed((DWIDTH+CWIDTH)-1 downto 0);
-- Registers
signal AccuClrxS : std_logic;
signal AccuxDP , AccuxDN : signed((DWIDTH+CWIDTH)-1 downto 0);
-- Registers
signal OutRegEnxS : std_logic;
signal OutRegxDP , OutRegxDN : std_logic_vector(DWIDTH -1 downto 0);
begin
--RamWriteEnxSO <= RamWriteEnxS;
------------------------------------------------------------
-- Input register
------------------------------------------------------------
InRegxDN <= DataInxDI;
p_inreg: process (ClkxCI ,ResetxRBI)
begin
if ResetxRBI=’0’ then
RamWritexDO <= (others => ’0’);
elsif ClkxCI ’event and ClkxCI=’1’ then
if InRegEnxS = ’1’ then
RamWritexDO <= InRegxDN;
end if;
end if;
end process p_inreg;
------------------------------------------------------------
-- Counters
------------------------------------------------------------
p_data: process (OffsetxDP , OffsetDecxS)
begin
OffsetxDN <= OffsetxDP;
if OffsetDecxS = ’1’ then
OffsetxDN <= OffsetxDP - "0000001";
end if;
end process p_data;
p_coef: process (CounterxDP , CounterIncxS)
begin
CounterxDN <= CounterxDP;
if CounterIncxS = ’1’ then

CounterxDN <= CounterxDP + "0000001";
end if;
end process p_coef;
------------------------------------------------------------
-- Counters
------------------------------------------------------------
-- two similar registers combined in one process
p_adrclk: process (ClkxCI ,ResetxRBI)
begin
CounterxDP <= (others => ’0’);
OffsetxDP <= (others => ’0’);
CounterxDP <= CounterxDN;
OffsetxDP <= OffsetxDN;
end if;
end process p_adrclk;
-- add and convert the address
RamAddrxDO <= std_logic_vector(OffsetxDP + CounterxDP);
LutAddrxDO <= std_logic_vector(CounterxDP);
------------------------------------------------------
-- ALU
------------------------------------------------------
-- type conversion
RamSignedxD <= signed(RamReadxDI);
LutSignedxD <= signed(LutReadxDI);
-- signed operations
MultxD <= RamSignedxD * LutSignedxD;
SumxD <= MultxD + AccuxDP;
--type conversion
SumStdxD <= std_logic_vector(SumxD);
-- simple truncate
--OutRegxDN<= SumStdxD((DWIDTH+CWIDTH)-1 downto CWIDTH);
OutRegxDN <= SumStdxD(DWIDTH -1 downto 0);
------------------------------------------------------
-- ALU
------------------------------------------------------
-- Accumulator next state
AccuxDN <= SumxD when AccuClrxS = ’0’ else (others => ’0’);
p_accu: process (ClkxCI , ResetxRBI)
begin
AccuxDP <= (others => ’0’);
elsif ClkxCI ’event and ClkxCI = ’1’ then
AccuxDP <= AccuxDN;
end if;
end process p_accu;
-------------------------------------------------------
-- Output register
-------------------------------------------------------
p_outreg: process (ClkxCI , ResetxRBI)
begin
if ResetxRBI= ’0’ then
OutRegxDP <= (others => ’0’);
if OutRegEnxS = ’1’ then

OutRegxDP <= OutRegxDN;
end if;
end if;
end process p_outreg;
DataOutxDO <= OutRegxDP;
-------------------------------------------------------
-- Control FSM
-------------------------------------------------------
p_fsm : process(StatexDP , DataInReqxSI ,
DataOutAckxSI , CounterxDP)
begin
--defaults
InRegEnxS <= ’0’;
OutRegEnxS <= ’0’;
AccuClrxS <= ’0’;
OffsetDecxS <= ’0’;
CounterIncxS <= ’0’;
RamWriteEnxSO <= ’0’;
DataInAckxSO <= ’0’;
DataOutReqxSO <= ’0’;
StatexDN <= StatexDP;
--case statements
case StatexDP is
when idle =>
if DataInReqxSI = ’1’ then
InRegEnxS <= ’1’;
StatexDN <= new_data;
end if;
when new_data =>
AccuClrxS <= ’1’;
RamWriteEnxSO <=’1’;
DataInAckxSO <= ’1’;
StatexDN <= run;
when run =>
CounterIncxS <= ’1’;
if CounterxDP = "1111111" then
OutRegEnxS <= ’1’;
OffsetDecxS <= ’1’;
StatexDN <= data_out;
end if;
when data_out =>
DataOutReqxSO <= ’1’;
if DataOutAckxSI = ’1’ then
StatexDN <= idle;
end if;
when others => null;
end case;
end process p_fsm;
p_clk : process (ClkxCI ,ResetxRBI)
begin
StatexDP <= idle;
StatexDP <= StatexDN;
end if;
end process p_clk;
end rtl;

A.2 File: filter_top.vhd
Listing A.2: RTL top model of filter and coefficient ROM.
library ieee;
entity filter_top is
generic (
CAW : integer := 7;
DAW : integer := 7
);
port (
);
end filter_top;
architecture rtl of filter_top is
------------------------------------------------------------
------------------------------------------------------------
component coeff
generic (
CWIDTH : integer;
CAW : integer);
port (
AddrxDI : in std_logic_vector(CAW -1 downto 0);
DataxDO : out std_logic_vector(CWIDTH -1 downto 0));
end component;
component dataRAM
generic (
DWIDTH : integer;
DAW : integer);
port (
AddrxDI : in std_logic_vector(DAW -1 downto 0);
WExSI : in std_logic;
WClkxCI : in std_logic;
DinxDI : in std_logic_vector(DWIDTH -1 downto 0);
DoutxDO : out std_logic_vector(DWIDTH -1 downto 0));
end component;
component filter
generic (
DWIDTH : integer;
DAW : integer);
port (

DataOutAckxSI : in std_logic;
LutAddrxDO : out std_logic_vector(CAW -1 downto 0);
LutReadxDI : in std_logic_vector(CWIDTH -1 downto 0);
RamWriteEnxSO : out std_logic;
RamAddrxDO : out std_logic_vector(DAW -1 downto 0);
RamReadxDI : in std_logic_vector(DWIDTH -1 downto 0);
RamWritexDO : out std_logic_vector(DWIDTH -1 downto 0));
end component;
signal RamWriteEnxS : std_logic;
signal RamAddrxD : std_logic_vector(DAW -1 downto 0);
signal RamReadxD : std_logic_vector(DWIDTH -1 downto 0);
signal RamWritexD : std_logic_vector(DWIDTH -1 downto 0);
signal LutAddrxD : std_logic_vector(CAW -1 downto 0);
signal LutReadxD : std_logic_vector(CWIDTH -1 downto 0);
begin
------------------------------------------------------------
-- Component Instantiations
------------------------------------------------------------
i_coeff: coeff
generic map (
CWIDTH => CWIDTH ,
CAW => CAW)
port map (
ClkxCI => ClkxCI ,
AddrxDI => LutAddrxD ,
DataxDO => LutReadxD);
i_dataRAM: dataRAM
generic map (
DWIDTH => DWIDTH ,
DAW => DAW)
port map (
AddrxDI => RamAddrxD ,
WExSI => RamWriteEnxS ,
WClkxCI => ClkxCI ,
DinxDI => RamWritexD ,
DoutxDO => RamReadxD);
i_filter: filter
generic map (
DWIDTH => DWIDTH ,
DAW => DAW)
port map (
ClkxCI => ClkxCI ,
DataOutAckxSI => DataOutAckxSI ,
LutAddrxDO => LutAddrxD ,
LutReadxDI => LutReadxD ,
RamWriteEnxSO => RamWriteEnxS ,
RamAddrxDO => RamAddrxD ,
RamReadxDI => RamReadxD ,

RamWritexDO => RamWritexD);
end rtl;
A.3 File: ﬁlter_soc.vhd
Listing A.3: RTL soc model.
library ieee;
--use ieee.numeric_std.all;
library techmap;
use techmap.gencomp.all;
entity filter_soc is
generic (
CAW : integer := 7;
DAW : integer := 7
);
port (
);
end filter_soc;
architecture rtl of filter_soc is
------------------------------------------------------------
------------------------------------------------------------
component filter_top is
generic (
CAW : integer := 7;
DAW : integer := 7
);
port (
);
end component;
------------------------------------------------------------
-- signal declarations

------------------------------------------------------------
signal ClkxCI_s : std_logic;
signal ResetxRBI_s : std_logic;
signal DataInxDI_s : std_logic_vector(DWIDTH -1 downto 0);
signal DataInReqxSI_s : std_logic;
signal DataInAckxSO_s : std_logic;
signal DataOutxDO_s : std_logic_vector(DWIDTH -1 downto 0);
signal DataOutReqxSO_s : std_logic;
signal DataOutAckxSI_s : std_logic;
signal VCCIO : std_ulogic_vector(7 downto 0);
signal GNDIO : std_ulogic_vector(7 downto 0);
signal VCCCO : std_ulogic;
signal GNDCO : std_ulogic;
constant padtech : integer := faraday;
constant padlevel : integer := 0;
begin
------------------------------------------------------------
-- Pad Instantiations
------------------------------------------------------------
-- Power Pads
io_VCCIO : vcciopadv generic map (width => 8, tech => padtech , limit => core_limited)
port map (VCCIO);
io_GNDIO : gndiopadv generic map (width => 8, tech => padtech , limit => core_limited)
port map (GNDIO);
io_VCCCO : vcccopad generic map (tech => padtech , limit => core_limited)
port map (VCCCO);
io_GNDCO : gndcopad generic map (tech => padtech , limit => core_limited)
port map (GNDCO);
-- Signal Pads
io_ClkxCI : inpad generic map (tech => padtech , level => padlevel , limit =>
core_limited)
port map (ClkxCI , ClkxCI_s);
io_ResetxRBI : inpad generic map (tech => padtech , level => padlevel , limit =>
core_limited)
port map (ResetxRBI , ResetxRBI_s);
io_DataInxDI : inpadv generic map (width => DWIDTH , tech => padtech , level => padlevel
, limit => core_limited)
port map (DataInxDI , DataInxDI_s);
io_DataInReqxSI : inpad generic map (tech => padtech , level => padlevel , limit =>
core_limited)
port map (DataInReqxSI , DataInReqxSI_s);
io_DataInAckxSO : outpad generic map (tech => padtech , level => padlevel , slew => fast
, limit => core_limited)
port map (DataInAckxSO , DataInAckxSO_s);
io_DataOutxDO : outpadv generic map (width => DWIDTH , tech => padtech , level =>
padlevel , slew => fast , limit => core_limited)
port map (DataOutxDO , DataOutxDO_s);
io_DataOutReqxSO : outpad generic map (tech => padtech , level => padlevel , slew =>
fast , limit => core_limited)
port map (DataOutReqxSO , DataOutReqxSO_s);
io_DataOutAckxSI : inpad generic map (tech => padtech , level => padlevel , limit =>
core_limited)
port map (DataOutAckxSI , DataOutAckxSI_s);
------------------------------------------------------------
-- Component Instantiations
------------------------------------------------------------
i_filter_top: filter_top
generic map (
CWIDTH => CWIDTH ,
CAW => CAW ,
DWIDTH => DWIDTH ,

DAW => DAW)
port map (
ClkxCI => ClkxCI_s ,
ResetxRBI => ResetxRBI_s ,
DataInxDI => DataInxDI_s ,
DataInReqxSI => DataInReqxSI_s ,
DataInAckxSO => DataInAckxSO_s ,
DataOutxDO => DataOutxDO_s ,
DataOutReqxSO => DataOutReqxSO_s ,
DataOutAckxSI => DataOutAckxSI_s
);
end rtl;
A.4 File: ﬁlter_soc_tb.vhd
Listing A.4: RTL testbench of the soc model.
--------------------------------------------------------------------------------
--
-- Title: Test Bench for Finite Impulse Response (FIR) Filter
--
-- Copyright (c) 1998,1999 by Mentor Graphics Corporation. All rights reserved.
--
-- This source file may be used and distributed without restriction provided
-- that this copyright statement is not removed from the file and that any
-- derivative work contains this copyright notice.
--
--------------------------------------------------------------------------------
LIBRARY ieee;
USE ieee.std_logic_1164.ALL;
USE ieee.std_logic_arith.ALL;
USE ieee.std_logic_signed.ALL;
USE ieee.math_real.ALL;
ENTITY filter_soc_tb IS
GENERIC( clock_delay : time := 16 ns;
CAW : integer := 7;
DAW : integer := 7
);
END filter_soc_tb;
ARCHITECTURE behavioral OF filter_soc_tb IS
component filter_soc is
generic (
CAW : integer := 7;
DAW : integer := 7
);
port (

);
end component;
SIGNAL ClkxCI : std_logic;
SIGNAL ResetxRBI : std_logic;
SIGNAL DataInxDI : std_logic_vector(DWIDTH -1 downto 0);
SIGNAL DataInReqxSI : std_logic;
SIGNAL DataInAckxSO : std_logic;
SIGNAL DataOutxDO : std_logic_vector(DWIDTH -1 downto 0);
SIGNAL DataOutReqxSO : std_logic;
SIGNAL DataOutAckxSI : std_logic;
BEGIN
-- Instantiate device-under-test.
dut: filter_soc
generic map (
CWIDTH => CWIDTH ,
CAW => CAW ,
DWIDTH => DWIDTH ,
DAW => DAW)
port map (
ClkxCI => ClkxCI ,
DataOutAckxSI => DataOutAckxSI
);
clock_generation:
PROCESS
BEGIN
-- Generate equal duty-cycle clock.
ClkxCI <= ’0’;
ClkxCI <= ’1’;
END PROCESS clock_generation;
generate_stimulus:
PROCESS
BEGIN
-- Initialize input signals.
-- Reset the design and wait for 2 clock cycles.
-- Wait for 2 more clock cycles before beginning test.

DataInxDI <= ( 0 => ’1’, OTHERS => ’0’ );
FOR I IN 127 DOWNTO 0 LOOP
WHILE DataInAckxSO= ’0’ LOOP
END LOOP;
WHILE DataOutReqxSO = ’0’ LOOP
END LOOP;
END LOOP;
--
-- Wait forever.
--
WAIT;
END PROCESS generate_stimulus;
END behavioral;

Appendix B
Appendix B: Technology independent
IO-cell library
The techmap generic IO-cell library contists of configurable input,
Figure B.1: Architectur
output and tri-state buffer cells. Figure B shows the architecture
of such IO buffer cell. Through specification of particular generics
one can configure the IO-cell. Port IO is the IO-pad to the out-
side world. Output ports of a toplevel cell are connected to I ports
of the IO-cells. Input ports of the toplevel cell are connected to
O ports of IO-cells. Input and output buffers have an enable port.
The strength, slew rate of output buffers are configurable through
E4,E8 and SR. PullUp/PullDown resistor and Schmittrigger behav-
ior of input buffers are configurable through generics PU, PD and
SMT. For the sake of ease for this course we use the following
generic iocell configurations. Table B.1 lists the available types of
IO-cells.
Table B.1: Techmap IO cells
Single IO Vector IO
Input inpad (pad, o) inpadv (pad, o)
Output outpad (pad, i) outpadv (pad, i)
IO iopad (pad, i, e, o) iopadv (pad, i, e, o)
iopadvv (pad, i, e, o)
Tri_state toutpad (pad, e, i) toutpadv (pad, e, i)
toutpadvv (pad, e, i)
67

APPENDIX B. APPENDIX B: TECHNOLOGY INDEPENDENT IO-CELL LIBRARY 68
The generic width is used to conﬁgure de width of the connected vectored in/output ports.
io_DataInxDI : inpadv
generic map (width => DWIDTH , tech => padtech ,
level => padlevel , limit => core_limited)
port map (DataInxDI , DataInxDI_s);
io_DataOutxDO : outpadv
generic map (width => DWIDTH , tech => padtech ,
level => padlevel , slew => fast , limit => core_limited)
port map (DataOutxDO , DataOutxDO_s);

Appendix C
Appendix C: Tool Scripts
C.1 Synopsys: Design Compiler
C.2 Cadence: SOC Encounter
C.2.1 start.tcl
#
#-----------------------------------------------------------------------------
# It is assumed that a project directory structure has already been
# created using ’create_project’ and that this synthesis script is
# executed from the project root directory $PROJECT_DIR
#-----------------------------------------------------------------------------
set PROJECT_DIR [pwd]
#-----------------------------------------------------------------------------
# Design related information (can be changed)
#-----------------------------------------------------------------------------
set DESIGN filter_soc
set TIM_MAX_LIBRARY fsd0a_a_generic_core_ss0p9v125c
set TIM_MIN_LIBRARY fsd0a_a_generic_core_ff1p1vm40c
set TIM_OC_MAX WCCOM ;# TYPICAL | WORST | WORST-IND
set TIM_OC_MIN BCCOM ;# TYPICAL | BEST | BEST-IND
# Floorplan settings
#
set FP_ASPECT_RATIO 1
set FP_ROW_DENSITY 0.85 ;# percent
set FP_CORE2IO 224 ;# micron
# Power ring and settings
#
set PR_WIDTH 2.8 ;# micron
set PR_SPACING 1.68 ;# micron
set PR_LAYER_TB ME7 ;# top and bottom layer
set PR_LAYER_LR ME8 ;# left and right layer
# Power stripe settings
#
set ST_NUM_SETS 1 ;# number of sets
set ST_SPACING 1.12 ;# micron
set ST_LAYER_V $PR_LAYER_LR
set ST_WIDTH 1.4 ;# micron
set ST_XOFS_R 0 ;# micron
set ST_XOFS_L 280 ;# micron
# Placement settings
69

APPENDIX C. APPENDIX C: TOOL SCRIPTS 70
#
set PL_EFFORT medium;# low | medium | high
# Clock tree synthesis settings
#
set CTS_BUFFER BUFCKX1
set CTS_INV INVCKX1
#-----------------------------------------------------------------------------
# Flags that drive the script behavior (can be changed)
#
# ADD_STRIPES (0 | 1)
# if 1, add stripes
# PLACE_TIMING (0 | 1)
# if 1, do a timing driven placement
# CLOCK_TREE (0 | 1)
# if 1, create a clock tree
# CTS_CREATE_SPEC (0 | 1)
# if 1, create a clock tree specification file with default values
# ROUTE_TIMING (0 | 1)
# if 1, do a timing driven routing
# OPT (string)
# can be used to have different generated file names
#-----------------------------------------------------------------------------
set ADD_STRIPES 1
set PLACE_TIMING 1
set CLOCK_TREE 1
set CTS_CREATE_SPEC 0
set ROUTE_TIMING 1
set OPT ""
#-----------------------------------------------------------------------------
# File names
#-----------------------------------------------------------------------------
set CONF_FILE_NAME ${DESIGN}.conf
set IO_FILE_NAME ${DESIGN}.io
set DESIGN_NAME ${DESIGN}${OPT}
set SAVE_DESIGN_FP_NAME ${DESIGN_NAME}-fplan.enc
set SAVE_DESIGN_PR_NAME ${DESIGN_NAME}-pplan.enc
set SAVE_DESIGN_PL_NAME ${DESIGN_NAME}-placed.enc
set SAVE_DESIGN_PF_NAME ${DESIGN_NAME}-placed_filled.enc
set SAVE_DESIGN_CT_NAME ${DESIGN_NAME}-cts.enc
set SAVE_DESIGN_RO_NAME ${DESIGN_NAME}-routed.enc
set TIM_RCDB_NAME ${DESIGN_NAME}.rcdb
set SDF_FILE_NAME ${DESIGN_NAME}-routed.sdf
set SPEF_FILE_NAME ${DESIGN_NAME}-routed.spef
set RPT_CHECK_TA_NAME ${DESIGN_NAME}-checkta.rpt
set RPT_REPORT_TA_NAME ${DESIGN_NAME}-ta.rpt
set RPT_SLACK_NAME ${DESIGN_NAME}-slack.rpt
set RPT_GATE_COUNT_NAME ${DESIGN_NAME}-gate_count.rpt
set RPT_NOTCH_NAME ${DESIGN_NAME}-notch.rpt
set RPT_CONN_NAME ${DESIGN_NAME}-conn.rpt
set RPT_GEOM_NAME ${DESIGN_NAME}-geom.rpt
set RPT_DENSITY_NAME ${DESIGN_NAME}-density.rpt
set VLOG_NETLIST_SIM_NAME ${DESIGN_NAME}-routed.v
set VLOG_NETLIST_LVS_NAME ${DESIGN_NAME}-routed_lvs.v
set CTS_SPEC_NAME ${DESIGN_NAME}-spec.ctstch
set CTS_RGUIDE_NAME ${DESIGN_NAME}-guide.cts
set CTS_RPT_NAME ${DESIGN_NAME}-cts.rpt
set GDS_FILE_NAME ${DESIGN_NAME}.gds
#-----------------------------------------------------------------------------
# Absolute paths
#-----------------------------------------------------------------------------
set CONF_FILE ${PROJECT_DIR}/PAR/CONF/${CONF_FILE_NAME}
set IO_FILE ${PROJECT_DIR}/PAR/CONF/${IO_FILE_NAME}

set SAVE_DESIGN_FP_FILE ${PROJECT_DIR}/PAR/DB/${SAVE_DESIGN_FP_NAME}
set SAVE_DESIGN_PR_FILE ${PROJECT_DIR}/PAR/DB/${SAVE_DESIGN_PR_NAME}
set SAVE_DESIGN_PL_FILE ${PROJECT_DIR}/PAR/DB/${SAVE_DESIGN_PL_NAME}
set SAVE_DESIGN_PF_FILE ${PROJECT_DIR}/PAR/DB/${SAVE_DESIGN_PF_NAME}
set SAVE_DESIGN_CT_FILE ${PROJECT_DIR}/PAR/DB/${SAVE_DESIGN_CT_NAME}
set SAVE_DESIGN_RO_FILE ${PROJECT_DIR}/PAR/DB/${SAVE_DESIGN_RO_NAME}
set SDF_FILE ${PROJECT_DIR}/PAR/TIM/${SDF_FILE_NAME}
set SPEF_FILE ${PROJECT_DIR}/PAR/TIM/${SPEF_FILE_NAME}
set TIM_RCDB_FILE ${PROJECT_DIR}/PAR/TIM/${TIM_RCDB_NAME}
set RPT_CHECK_TA_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_CHECK_TA_NAME}
set RPT_REPORT_TA_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_REPORT_TA_NAME}
set RPT_SLACK_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_SLACK_NAME}
set RPT_GATE_COUNT_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_GATE_COUNT_NAME}
set RPT_NOTCH_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_NOTCH_NAME}
set RPT_CONN_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_CONN_NAME}
set RPT_GEOM_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_GEOM_NAME}
set RPT_DENSITY_FILE ${PROJECT_DIR}/PAR/RPT/${RPT_DENSITY_NAME}
set VLOG_NETLIST_SIM_FILE ${PROJECT_DIR}/HDL/GATE/${VLOG_NETLIST_SIM_NAME}
set VLOG_NETLIST_LVS_FILE ${PROJECT_DIR}/HDL/GATE/${VLOG_NETLIST_LVS_NAME}
set CTS_SPEC_FILE ${PROJECT_DIR}/PAR/CTS/${CTS_SPEC_NAME}
set CTS_RGUIDE_FILE ${PROJECT_DIR}/PAR/CTS/${CTS_RGUIDE_NAME}
set CTS_RPT_FILE ${PROJECT_DIR}/PAR/RPT/${CTS_RPT_NAME}
set GDS_FILE ${PROJECT_DIR}/PAR/DEX/${GDS_FILE_NAME}
set GDS_MAP_FILE ${PROJECT_DIR}/PAR/DEX/gds2.map
#-----------------------------------------------------------------------------
# Suppress Messages
#-----------------------------------------------------------------------------
suppressMessage NRDB 733
suppressMessage NREX 4 28 30
suppressMessage SOCEXT 3032 3080
suppressMessage SOCLF 58 200
suppressMessage SOCOPT 3544
suppressMessage SOCPP 2008
suppressMessage TCLNL 330
suppressMessage TECHLIB 436
#-----------------------------------------------------------------------------
# Procedures
#-----------------------------------------------------------------------------
# make_clock_tree
#
proc make_clock_tree create_spec {
global PROJECT_DIR CTS_BUFFER CTS_INV CTS_SPEC_FILE CTS_RGUIDE_FILE CTS_RPT_FILE
if { $create_spec || ![file exists $CTS_SPEC_FILE] } {
#createClockTreeSpec
#-bufFootprint $CTS_BUFFER
#-invFootprint $CTS_INV
#-output $CTS_SPEC_FILE
createClockTreeSpec
-output $CTS_SPEC_FILE
}
specifyClockTree -file $CTS_SPEC_FILE
ckSynthesis
-rguide $CTS_RGUIDE_FILE
-report $CTS_RPT_FILE
optDesign -postCTS -drv -outDir ${PROJECT_DIR}/PAR/RPT
} ;# make_clock_tree
#-----------------------------------------------------------------------------
# Load configuration file
#-----------------------------------------------------------------------------
loadConfig $CONF_FILE
#-----------------------------------------------------------------------------

# Load IO file
#-----------------------------------------------------------------------------
loadIoFile $IO_FILE
#-----------------------------------------------------------------------------
# Set operating conditions
#-----------------------------------------------------------------------------
setOpCond
-max $TIM_OC_MAX -maxLibrary $TIM_MAX_LIBRARY
-min $TIM_OC_MIN -minLibrary $TIM_MIN_LIBRARY
#
setDesignMode -process 90
#-----------------------------------------------------------------------------
# Set user grids
#-----------------------------------------------------------------------------
setPreference ConstraintUserXGrid 0.28
setPreference ConstraintUserXOffset 0.28
setPreference ConstraintUserYGrid 0.28
setPreference ConstraintUserYOffset 0.28
setPreference SnapAllCorners 1
setPreference BlockSnapRule 2
#-----------------------------------------------------------------------------
# Define global Power nets - make global connections
#-----------------------------------------------------------------------------
clearGlobalNets
globalNetConnect VCC -type pgpin -pin VCC -inst * -module {} -verbose
globalNetConnect GND -type pgpin -pin GND -inst * -module {} -verbose
globalNetConnect VCC -type tiehi -module {} -verbose
globalNetConnect GND -type tielo -module {} -verbose
#globalNetConnect PD -type pgpin -pin {IO VCC2O} -inst io_VCCIO -module {} -verbose
-override
applyGlobalNets
setDrawView fplan
fit
C.2.2 fplan.tcl
#-----------------------------------------------------------------------------
# Initialize floorplan
#-----------------------------------------------------------------------------
#floorPlan -b 0.0 0.0 1872.08 1872.08
# 219.8 219.8 1092.28 1092.28
# 779.8 779.8 1092.28 1092.28
#floorPlan -b 0.0 0.0 1872.08 1872.08
# 219.8 219.8 1652.28 1652.28
# 261.8 261.8 1610.28 1610.28
#floorPlan -d 1872.08 1872.08
# 280.0 280.0 280.0 280.0
floorPlan -d 1872.08 1872.08
560.0 560.0 560.0 560.0
#floorPlan -d 3874.92 1874.88
# 1400.0 560.0 1400.0 560.0
#snapFPlanIO -usergrid

#snapFPlan -all
#setPlanDesignMode -useExistingPowerRail true
#setPlanDesignMode -fixPlacedMacros true
#setPlanDesignMode -groupHardMacro true -effort medium -boundaryPlace true
setPlanDesignMode -groupHardMacro true -boundaryPlace true
planDesign
#finishFloorplan -autoHalo -autoBlockage -staircase
finishFloorplan -addHalo 14 -autoBlockage
source ${PROJECT_DIR}/PAR/BIN/fillperi.tcl
saveDesign $SAVE_DESIGN_FP_FILE
setDrawView fplan
fit
C.2.3 pplan.tcl
## File : pwr.tcl
## Created at : Mon Jun 07 16:33:03 CEST 2010
## Created by : Alexander de Graaf
puts "----------------- Power Planning ------------------------------------------"
set crwidth 2.8
set crspace 2.80
set croffset 28.00
set brwidth 1.12
set brspace 0.56
set broffset 4.20
set vswidth 0.94
set vsspace 1.68
set vsoffset 2.80
set hswidth 0.94
set hsspace 1.68
set hsoffset 2.80
cutRow
clearCutRow
deselectAll
##################################################################################
#
# Generate core rings
#
##################################################################################
puts "----------------- Making Power Rings ---------------------------------------"
setAddRingOption -avoid_short 0 -ignore_rows 0
addRing -nets {GND VCC} -around core
-layer_top ME5 -layer_bottom ME5
-layer_left ME6 -layer_right ME6
-width_top $crwidth -width_bottom $crwidth -width_left $crwidth -width_right
$crwidth
-spacing_top $crspace -spacing_bottom $crspace -spacing_left $crspace -spacing_right
$crspace
-offset_top $croffset -offset_bottom $croffset -offset_left $croffset -offset_right
$croffset
-snap_wire_center_to_grid None
# -center 1

deselectAll
#
##################################################################################
#
# Generate block rings
#
##################################################################################
#
# Generate block ring around buffer memory
selectInst i_filter_top/i_dataRAM_i_dmem
setAddRingOption -avoid_short 0 -ignore_rows 0 -extend_over_row 0
addRing -nets {GND VCC} -type block_rings -around selected
-width_top $brwidth -width_bottom $brwidth -width_left $brwidth -width_right
$brwidth -threshold auto
-spacing_top $brspace -spacing_bottom $brspace -spacing_left $brspace -spacing_right
$brspace
-offset_top $broffset -offset_bottom $broffset -offset_left $broffset -offset_right
$broffset
-use_wire_group 1 -use_interleaving_wire_group 0 -use_wire_group_bits 1
deselectAll
#
# Generate block ring around coefficient rom
selectInst i_filter_top/i_coeff_a9d16
setAddRingOption -avoid_short 0 -ignore_rows 0 -extend_over_row 0
addRing -nets {GND VCC} -type block_rings -around selected
-width_top $brwidth -width_bottom $brwidth -width_left $brwidth -width_right
$brwidth -threshold auto
-spacing_top $brspace -spacing_bottom $brspace -spacing_left $brspace -spacing_right
$brspace
-offset_top $broffset -offset_bottom $broffset -offset_left $broffset -offset_right
$broffset
-use_wire_group 1 -use_interleaving_wire_group 0 -use_wire_group_bits 1
deselectAll
##################################################################################
#
# Generate stripes
#
##################################################################################
#
#puts "----------------- Making Power Stripes ------------------------------------"
#setAddStripeOption -remove_floating_stripe_over_block 1
#addStripe -nets {GND VCC} -direction vertical -layer ME4
# -width $vswidth -spacing $vsspace -set_to_set_distance 300.16
# -xleft_offset 200.20 -xright_offset 84.0
# -extend_to none -merge_stripes_value auto -break_stripes_at_block_rings 1
#deselectAll
##################################################################################
#
# Route VCC and GND core rings to pad pins of VCC/GND IO-cells
#
##################################################################################
#
#sroute -noCorePins -noPadRings -noStripes -jogControl { preferWithChanges
differentLayer } -nets {GND VCC}
sroute -allowJogging 1 -allowLayerChange 1 -nets {GND VCC}

#
saveDesign $SAVE_DESIGN_PR_FILE
setDrawView fplan
fit
puts "----------------- Power Planning done --------------------------------------"

Appendix D
Appendix D: Design Metrics
A design begins with the planning of the die. The mini@sic program from EuroPractice is a multiproject
wafer where a minimum area of 1875 x 1875 um2 is required. This area constraint is the startpoint for
planning the whole chip. Another important issue is the cell library metrics. The metrics of Faraday
L90_SP library are:
Description Width Height
Grid 0.28 um 0.28 um
Core Cell x * 0.28 um 2.8 um
IO Cell 60.48 um 142.8 um
Corner Cell 142.8 um 142.8 um
Pad Cell 64 um 77 um
76

APPENDIX D. APPENDIX D: DESIGN METRICS 77

Tutorial for EDA Tools:

More Related Content

Viewers also liked (20)

Similar to Tutorial for EDA Tools: (20)

More from Minh Anh Nguyen (20)

Recently uploaded (20)

Tutorial for EDA Tools: