![Spark ignition engine (SI engine)
An engine in which the combustion process in each cycle is started
by use of an external spark.
Compression ignition engine (CI engine)
An engine in which the combustion process starts when the air-fuel
mixture self ignites due to high temperature in the combustion
chamber caused by high compression.
[Spark ignition and Compression Ignition engine operate on either a
four stroke cycle or a two stroke cycle]](https://image.slidesharecdn.com/unit1icengine1-240901070459-78ecd011/85/Unit-1-Internal-combustion-engine-a-part-of-applied-thermodynamics-8-320.jpg)
Unit 1 Internal combustion engine a part of applied thermodynamics
- 1. Introduction to Internal Combustion Engines
- 2. • = HEAT ENGINE Any engine that converts thermal energy to mechanical work output. Ex: steam engine, steam power plant, jet engine, gas turbine power plant, diesel engine, and gasoline (petrol) engine etc.
- 3. HEAT ENGINE Internal Combustion (IC) Engine External Combustion Engine On the basis of how thermal energy is being delivered to working fluid of the heat engine, Heat engine can be classified as
- 4. Internal combustion engine: Combustion takes place within the working fluid of the engine, • Thus fluid gets contaminated in combustion. • Petrol engine is an example of internal combustion engine, where the working fluid is a mixture of air and fuel . External combustion engine Working fluid gets energy from outside through some heat exchanger (Boiler) • Thus the working fluid does not come in contact with combustion products. • Steam engine is an example of external combustion engine, where the working fluid is steam.
- 7. INTERNAL COMBUSTION ENGINES Spark Ignition engines (ex. Gasoline/Petrol Engine) Compression Ignition engines (ex. Diesel Engine)
- 8. Spark ignition engine (SI engine) An engine in which the combustion process in each cycle is started by use of an external spark. Compression ignition engine (CI engine) An engine in which the combustion process starts when the air-fuel mixture self ignites due to high temperature in the combustion chamber caused by high compression. [Spark ignition and Compression Ignition engine operate on either a four stroke cycle or a two stroke cycle]
- 9. Figure 1 : IC Engine components
- 10. Figure 2 : Schematic View of Engine
- 11. I C Engine Components • Block : Body of the engine containing cylinders, made of cast iron or aluminium. • Cylinder : The circular cylinders in the engine block in which the pistons reciprocate back and forth. • Head : The piece which closes the end of the cylinders, usually containing part of the clearance volume of the combustion chamber. • Combustion chamber: The end of the cylinder between the head and the piston face where combustion occurs.
- 12. • Crankshaft : Rotating shaft through which engine work output is supplied to external systems. – The crankshaft is connected to the engine block with the main bearings. – It is rotated by the reciprocating pistons through the connecting rods connected to the crankshaft, offset from the axis of rotation. This offset is sometimes called crank throw or crank radius. • Connecting rod : Rod connecting the piston with the rotating crankshaft, usually made of steel or alloy forging in most engines but may be aluminum in some small engines. • Piston rings: Metal rings that fit into circumferential grooves around the piston and form a sliding surface against the cylinder walls.
- 13. • Camshaft : Rotating shaft used to push open valves at the proper time in the engine cycle, either directly or through mechanical or hydraulic linkage (push rods, rocker arms, tappets) . • Crankcase : Part of the engine block surrounding the crankshaft. – In many engines the oil pan makes up part of the crankcase housing. • Exhaust manifold : Piping system which carries exhaust gases away from the engine cylinders, usually made of cast iron .
- 14. • Intake manifold :Piping system which delivers incoming air to the cylinders, usually made of cast metal, plastic, or composite material. – In most SI engines, fuel is added to the air in the intake manifold system either by fuel injectors or with a carburetor. – The individual pipe to a single cylinder is called runner. • Spark plug : Electrical device used to initiate combustion in an SI engine by creating high voltage discharge across an electrode gap.
- 15. • Flywheel : Rotating mass with a large moment of inertia connected to the crank shaft of the engine. – The purpose of the flywheel is to store energy and furnish large angular momentum that keeps the engine rotating between power strokes and smooths out engine operation. • Fuel injector : A pressurized nozzle that sprays fuel into the incoming air (SI engines )or into the cylinder (CI engines). • Fuel pump : Electrically or mechanically driven pump to supply fuel from the fuel tank (reservoir) to the engine.
- 17. IC Engines SI Ignition System CI Working Cycle Otto Cycle Diesel Cycle Brayton Cycle Cylinder Arrangement Four Stroke No. of Strokes Two Stroke Stationary Application Mobile Air Cooled Cooling System Liquid Cooled Single Cyl No. of Cylinders Multi Cyl Vertical / Straight I n l i n e Horizontal / Flat V, W, H, U, X etc. Radial Vertical / Straight Opposed Horizontal / Flat
- 18. Bugatti W 16 Subaru H6
- 19. • Four stroke cycle : It has four piston strokes over two revolutions for each cycle. • Two stroke cycle : It has two piston strokes over one revolution for each cycle.
- 20. Figure 3: Engine Terminology
- 21. • Figure, shows the pressure volume diagram of ideal engine cycle along with engine terminology as follows: • Top Dead Center (TDC): • Position of the piston when it stops at the furthest point away from the crankshaft. Top because this position is at the top of the engines (not always), and dead because the piston stops as this point. Because in some engines TDC is not at the top of the engines (e.g: horizontally opposed engines, radial engines,etc). • Some sources call this position Head End Dead Center (HEDC). • Some source call this point TOP Center (TC). • When the piston is at TDC, the volume in the cylinder is a minimum called the clearance volume. Engine Terminology :
- 22. Bottom Dead Center (BDC) • Position of the piston when it stops at the point closest to the crankshaft. • Some sources call this Crank End Dead Center (CEDC) because it is not always at the bottom of the engine.Some source call this point Bottom Center (BC). • Stroke : Distance traveled by the piston from one extreme position to the other : TDC to BDC or BDC to TDC. • Bore :It is defined as cylinder diameter or piston face diameter; piston face diameter is same as cylinder diameter( minus small clearance). • Swept volume/Displacement volume : Volume displaced by the piston as it travels through one stroke. • Swept volume is defined as stroke times bore. • Displacement can be given for one cylinder or entire engine (one cylinder times number of cylinders).
- 23. • Clearance volume : It is the minimum volume of the cylinder available for the charge (air or air fuel mixture) when the piston reaches at its outermost point (top dead center or outer dead center) during compression stroke of the cycle. – Minimum volume of combustion chamber with piston at TDC. • Compression ratio : The ratio of total volume to clearance volume of the cylinder is the compression ratio of the engine. Typically compression ratio for SI engines varies form 8 to 12 and for CI engines it varies from 12 to 24
- 24. SI Engine Ideal Otto Cycle We will be dealing with four stroke SI engine, the following figure shows the PV diagram of Ideal Otto cycle.
- 28. Figure 4 : Suction stroke
- 29. Four strokes of SI Engine Cycle : Suction/Intake stroke: Intake of air fuel mixture in cylinder through intake manifold. The piston travel from TDC to BDC with the intake valve open and exhaust valve closed. This creates an increasing volume in the combustion chamber, which in turns creates a vacuum. The resulting pressure differential through the intake system from atmospheric pressure on the outside to the vacuum on the inside causes air to be pushed into the cylinder. As the air passes through the intake system fuel is added to it in the desired amount by means of fuel injectors or a carburettor.
- 30. Figure 5 : Compression Stroke
- 31. • Compression stroke: • When the piston reaches BDC, the intake valve closes and the piston travels back to TDC with all valves closed. • This compresses air fuel mixture, raising both the pressure and temperature in the cylinder. • Near the end of the compression stroke the spark plug is fired and the combustion is initiated.
- 32. • Combustion of the air-fuel mixture occurs in a very short but finite length of time with the piston near TDC (i.e., nearly constant volume combustion). • It starts near the end of the compression stroke slightly before TDC and lasts into the power stroke slightly after TDC. • Combustion changes the composition of the gas mixture to that of exhaust products and increases the temperature in the cylinder to a high value. • This in turn increases the pressure in the cylinder to a high value.
- 33. Figure 6 : Combustion followSa enk dar,D bM yE,R ESE xT pansion stroke.
- 34. • Expansion stroke/Power stroke: • With all valves closed the high pressure created by the combustion process pushes the piston away from the TDC. • This is the stroke which produces work output of the engine cycle. • As the piston travels from TDC to BDC, cylinder volume is increased, causing pressure and temperature to drop.
- 35. Exhaust Blowdown: Late in the power stroke, the exhaust valve is opened and exhaust blowdown occurs. Pressure and temperature in the cylinder are still high relative to the surroundings at this point, and a pressure differential is created through the exhaust system which is open to atmospheric pressure. • This pressure differential causes much of the hot exhaust gas to be pushed out of the cylinder and through the exhaust system when the piston is near BDC. • This exhaust gas carries away a high amount of enthalpy, which lowers the cycle thermal efficiency. • Opening the exhaust valve before BDC reduces the work obtained but is required because of the finite time needed for exhaust blowdown.
- 36. Figure7: Exhaust blowdown followed by Exhaust stroke Sankar,DME,RSE
- 37. • Exhaust stroke: • By the time piston reaches BDC, exhaust blowdown is complete, but the cylinder is still full of exhaust gases at approximately atmospheric pressure. • With the exhaust valve remaining open, the piston travels from BDC to TDC in the exhaust stroke. • This pushes most of the remaining exhaust gases out of the cylinder into the exhaust system at about atmospheric pressure, leaving only that trapped in the clearance volume when the piston reaches TDC.
- 38. Near the end of the exhaust stroke before TDC, the intake valve starts to open, so that it is fully open by TDC when the new intake stroke starts the next cycle. Near TDC the exhaust valve starts to close and finally is fully closed sometime after TDC. This period when both the intake valve and exhaust valve are open is called valve overlap, it can be clearly seen in valve timing chart given below.
- 40. Compression Ignition Engine : • We will deal with Compression Ignition engine. • The ideal diesel cycle PV diagram is shown in following figure 8.
- 41. Figure 8: Ideal diesel cycle P-V Diagram.
- 42. Figure 9 : Four strokes of ideal Diesel cycle.
- 45. Four strokes of CI Engine Cycle : • Intake/Suction Stroke : The same as the intake stroke in an SI engine with one major difference : no fuel is added to the incoming air, refer figure 10. • Compression Stroke : The same as in an SI engine except that only air is compressed and compression is to higher pressures and temperature, refer figure11. • Late in the compression stroke fuel is injected directly into the combustion chamber, where it mixes with very hot air. • This causes the fuel to evaporate and self ignite, causing combustion to start. » Combustion is fully developed by TDC and continues at about constant pressure until fuel injection is complete and the piston has started towards BDC, refer figure12.
- 46. Figure12: Fuel injection and combustion followed by Expansion stroke Asst. Prof. Vishnu Sankar,DME,RSE
- 47. Figure13: Exhaust stroke followed by exhaust blowdown. nu Sankar,DME,RSET
- 48. • Expansion/Power stroke : The power stroke continues as combustion ends and the piston travels towards BDC, refer figure 12. • Exhaust blowdown same as with an SI engine. • Exhaust stroke : Same as with an SI engine, refer figure 13.
- 50. Previous year questions 1. A petrol engine having a compression ratio of 6 uses a fuel with calorific valve of 42 MJ/kg. The air fuel ratio is 15: 1. Pressure and temperature at the start of the suction stroke is 1 bar and 57°C respectively. Determine the maximum pressure in the cylinder if the index of compression is 1.3 and specific heat at constant volume is given by C (0.678 +0.00013 T) kJ/kgK. Compare this value with that obtained when C=0-717 kJ/KgK. 2. What will be the effect on the efficiency of an otto cycle having a compression ratio of 7, if the specific heat at constant volume increases by 1%.
- 51. 3. A trial carried out in a four stroke single cylinder gas engine gave the following results. Cylinder dia=300 mm, Engine stroke=500mm, Clearance volume=6750cc, Explosions per minute=100 Pmax KN/m2 = 765 Net work load on the brake=190kg Brake dia=1.5m Rope dia=2 5mm, Speed of the engine=240rpm, Gas used=30 m3/kghr , Calorific value of gas=2 0515 KJ/ m3 . Determine compression rat io, mechanical efficiency, indicated thermal efficiency, air standard efficiency, relative efficiency, assume r=1.4. 4. The following observat ions are recorded during a test on a four-stroke petrol engine, F.C = 3000 of fuel in 12sec, speed of the engine is 2500rpm, B.P = 20KW, Air intake orifice diameter = 35 mm,Pressure across the orifice = 140mm of water coefficient of discharge of orifice = 0.6 , piston diameter = 150mm, stroke length = 100 mm, Density of the fuel = 0.85gm/cc , r=6 .5, Cv of fuel = 42000KJ/Kg, Barometric pressure = 760mm of Hg , Room temperature = 24oC.
- 52. 5. 42.5 kW engine has a mechanical efficiency of 85%. If the frictional power is assumed to be constant with load, what is the mechanical efficiency at 60% of the load? 6. A six cylinder, four stroke IC engine develops 100 KW of brake power at 800 rpm. The stroke to bore ratio is 1.5. The indicated mean effective pressure is 8 bar and mechanical efficiency is 80 %. Determine the cylinder diameter and piston stroke of the engine.