Unit 1.pptx
- 1. Transfer Function Representation Transfer Function of DC Servomotor • DC servomotor is essentially an ordinary DC motor except with very few variations in its constructional features. • It gives quick response to control signals & possess low Inertia and high starting torque. • Two different modes in which the DC motor can be operated are 1. Field Controlled Mode 2. Armature Controlled Mode
- 2. 1. T.F of Field Controlled DC servomotor • The speed of the DC motor is directly proportional to armature voltage and inversely proportional to the flux. • In field controlled DC motor the armature voltage is kept constant and speed is varied by varying the flux of the machine. • Since flux is directly proportional to field current, the flux is varied by varying the field current. • The speed control system is an electromechanical control system. • The electrical system consists of armature & field ckt but for analysis purpose, only field ckt is considered bcoz the armature is excited by by a constant voltage.
- 3. • The mechanical system consists of the rotating part of the motor and the load connected to the shaft of the motor. • The field controlled DC motor speed control system is shown below.
- 4. • Let, • The equivalent ckt of field is • By KVL, we can write
- 5. • The torque of DC motor is proportional to product of flux and armature current. • Since armature current is constant in this system, the torque is proportional to flux alone, but flux is proportional to field current. i.e • The mechanical system of the motor is shown in below fig. • The differential eqn governing the system of motor is
- 8. 2. T.F of Armature Controlled DC servomotor • The speed of the DC motor is directly proportional to armature voltage and inversely proportional to the flux. • In armature controlled DC motor the desired speed is obtained by varying the armature voltage. • This speed control system is an electromechanical control system. • The electrical system consists of armature and the field ckt but for analysis purpose, only the armature ckt is considered bcoz the field is excited by a constant voltage. • The mechanical system consist of the rotating part of the motor & load connected to the shaft of the motor.
- 9. • The armature controlled DC motor speed control system is shown below. • Let,
- 10. • The equivalent ckt of armature is • By KVL, we can write • The torque of DC motor is proportional to product of flux and armature current. • Since the flux is constant in this system, the torque is proportional to armature current alone. i.e
- 11. • The mechanical system of the motor is shown in fig. • The differential eqn governing the mechanical system of the motor is given by, • The back emf of DC machine is proportional to speed (angular velocity) of shaft.
- 15. • Characteristics of DC Servomotor: • Field controlled DC motor is open loop while armature controlled DC motor is closed loop system. • Hence armature controlled DC motors are preferred over field controlled type.
- 16. AC Servomotor • Most of the servomotors used in low power servomechanisms are AC servomotors. • The AC servomotor is basically a two-phase induction motor with some special design features. • The output of AC servomotor varies from fraction watts to few hundred watts. • The operating frequency is 50Hz to 400Hz.
- 17. Construction: • It is mainly divided into two parts namely stator & rotor. Stator: • The stator carries two windings uniformly distributed and displayed by 90o in space. • One winding is called main winding, this is excited by a constant voltage AC supply. • The other winding is called control winding, it is excited by variable control voltage which is obtained from a servoamplifier. • This voltage is 90o out of phase with respect to the voltage applied to the reference winding.
- 18. • The stator of the AC servomotor is shown below.
- 20. • The other type of rotor is drag cup type rotor. There are two air gaps in such construction. • Such construction reduces Inertia considerably and hence such type of rotor is used in very low power applications. • The Aluminium is used for the cup construction. • The construction is shown in fig.
- 21. Torque Speed Characteristics: • The Torque – speed characteristics of two phase induction motor mainly depends on the ratio of reactance to resistance. • For small X to R ratio i.e high resistance and low reactance motor, the characteristics are much more linear while it is non-linear for large X to R ratio as shown in fig(d).
- 22. • In practice design of the motor is so as to get almost linear torque-speed characteristics. • The fig(e) shows the torque-speed characteristics for various control voltages. • The torque varies almost linearly with speed. • All the characteristics are equally spaced for equal increments of control voltages. • It is generally operated with low speeds. • AC servo motors widely used in Instrument Servomechanisms, remote positioning devices, process control systems, self balancing recorders, computers tracking, guidance systems, robotics & machine tools, etc.,
- 23. Transfer Function of AC Servomotor • Let, Tm = Torque developed by Servomotor Ɵ = Angular displacement of rotor ω = 𝑑𝜃 𝑑𝑡 = Angular speed TL = Torque required by the load J = Moment of Inertia of load and the rotor B = Viscous – frictional coefficient of load and the rotor K1 = Slope of control phase voltage Vs Torque characteristics K2 = Slope of speed – torque characteristics
- 24. • With reference to fig(e), we can say that for speeds near zero all the curves are straight lines parallel to the Torque at rated i/p voltage (ec = E) and are equally spaced for equal increments of i/p voltage. • Under this assumption the torque developed by the motor is represented by the equation Torque developed by motor Tm = --------- (1) • The rotating part of motor & the load can be modelled by the equation TL =
- 25. • At equilibrium the motor torque is equal to load torque ------------- (3) • On taking L.T of eqn(3) with zero initial conditions, we get
- 28. Synchro Transmitter and Receiver SYNCHROS • The term synchro is a generic name for a family of Inductive devices which works on the principle of a rotating transformer (Induction Motor). • A synchro is an electromagnetic transducer used to convert an angular position of shaft into an electric signal. It is commercially known as selsyn or autosyn. • It produces an output voltage depending upon angular position of the motor. • A synchro system is formed by interconnection of the devices called the synchro transmitter and the synchro control transformer.
- 29. • They are also called synchro pair. • The synchro pair measures & compares two angular displacements and its o/p voltage is approximately linear with angular difference of the axis of both the shafts. • They can be used in the following two ways. 1. To control the angular position of load from a remote place/ long distance. 2. For automatic correction of changes due to disturbance in the angular position of the load.
- 30. Synchro Transmitter Construction: • The constructional features, electrical ckt & a schematic symbol of synchro transmitter are shown in fig. • The two major parts of synchro transmitter are stator and rotor.
- 31. • The stator is made up of laminated silicon steel and slotted on the inner periphery to accommodate a balanced 3-phase winding. • The stator winding is concentric type with the axis of 3 coils 120o apart. The stator winding is star connected i.e Y-connection. • The rotor is of dumb bell construction with a single winding. • The ends of rotor winding are terminated on two slip rings. • A single phase ac excitation voltage is applied to rotor through slip rings.
- 32. Working Principle: • When the rotor is excited by ac voltage, the rotor current flows , and a magnetic field is produced. • The rotor magnetic field induces an emf in the stator coils by transformer action. • The effective voltage induced in any stator coil depends upon the angular position of the coil’s axis w.r.t rotor axis. Let, er = Instantaneous value of AC voltage applied to rotor. es1,es2, es3 = Instantaneous value of emf induced in stator coils S1, S2, S3 w.r.t neutral respectively. Er = Maximum value of rotor excitation voltage. ω = Angular frequency of rotor excitation voltage. Kt = Turns ratio of stator and rotor winding. Kc = Coupling coefficient. Ɵ = Angular displacement of rotor w.r.t reference.
- 33. Let, The instantaneous value of excitation voltage, er = Er Sinωt • Let the rotor rotates in anticlockwise direction. When the rotor rotates by an angle Ɵ, emfs are induced in stator coils. • The frequency of induced emf is same as that of rotor frequency. • The magnitude of induced emfs are proportional to the turns ratio and coupling coefficient. • The turns ratio, Kt is a constant, but coupling coefficient, Kc is a function of rotor angular position. Therefore, Induced emf in stator coil = Kt Kc Er sin ωt ---------(1)
- 34. • When Ɵ=0, the flux linkage of coil S2 is maximum and when Ɵ= 90o, the flux linkage of coil S2 is zero. Hence the flux linkage of coil S2 is function of CosƟ. • The flux linkage of coil S3 ill be maximum after rotation of 120o in anticlockwise direction and that of S1 after a rotation of 240o . Therefore, Coupling coefficient, Kc for coil -S2 = K1 CosƟ ----------(2) Coupling coefficient, Kc for coil -S3 = K1 Cos(Ɵ-120o) --------(3) Coupling coefficient, Kc for coil -S1 = K1 Cos(Ɵ-240o) ---------(4)
- 35. • Hence the emfs of stator coils w.r.t Neutral can be expressed as follows. es2 = K1 Kt CosƟ ErSinωt = K Er CosƟ Sinωt ---------(5) es3 = K1 Kt Cos(Ɵ-120o) ErSinωt = K ErCos(Ɵ-120o) Sinωt ------(6) es1 = K1 Kt Cos(Ɵ-240o) ErSinωt = K ErCos(Ɵ-240o) Sinωt ------(7) • With reference to fig. by KVL the coil-to-coil emf can be expressed as es1s2 = es1 - es2 = √3 K Ersin(Ɵ+240o) Sinωt -------- (8) es2s3 = es2 - es3 = √3 K Ersin(Ɵ+120o) Sinωt ---------(9) es3s1 = es3 - es1 = √3 K ErsinƟ Sinωt ---------(10)
- 36. • When Ɵ=0, from eqn5 we can say that maximum emf is induced in coil S2. • But from eqn10 it is observed that th ecoil-to-coil voltage es3s1 is zero. • This position of the rotor is defined as the electrical zero of the transmitter. • The electrical zero position is used as reference for specifying the angular position of rotor. • The i/p to syncho transmitter is the angular position of its rotor shaft and the o/p is a set of 3 stator coil-to-coil voltages. • By measuring & identifying the set of voltages at the stator terminals, it is to identify the angular position of the rotor. • A device called synchro/digital converter is available to measure the stator voltages & to calculate the angular measure and then display the direction & angle of rotation.
- 37. • Synchro Control Transformer:
- 41. Synchro as error detector
- 43. Block Diagram Representation of Electrical Systems • Electrical systems contain mainly three basic elements — resistor, inductor and capacitor. • Consider a serries off RLC circuit as shown in the following figure. Where,, Vi(t) and Vo(t) are the input and output voltages. • Let i(t) be the current passing through the circuit. This circuit is in time domain.
- 44. • By applying the L.T to this circuit, will get the circuit in s-domain. • The circuit is as shown in the following figure. • From the above ckt, we can write
- 45. • Let us now draw the block diagrams for these two equations individually. And then combine those block diagrams properly in order to get the overall block diagram of series off RLC Circuit (s--domain).
- 46. • Equation 1 can be implemented with a block having the transfer function, • The input and output of this block are • We require a summing point to get • The block diagram of Equation 1 is shown in the following figure.
- 47. • Equation2 can be implemented with a block having transfer function, • The input and output of this block are • The block diagram of Equation 2 is shown in the following figure. • The overall block diagram of the series of RLC Circuit (s-domain) is shown in the following figure.
- 49. • Similarly,, you can draw the block diagram of any electrical circuit or system just by following this simple procedure. • Convert the time domain electrical circuit into an s-domain electrical circuit by applying L.T. • Write down the equations for the current passing through allll series branch elements and voltage across all shunt branches. • Draw the block diagrams for all the above equations individually. • Combine all these block diagrams properly in order to get the overall block diagram of the electrical circuit (s-domain).
- 50. Block Diagram Algebra • A Block Diagram of a system is a pictorial representation of the functions performed by each component and of the flow of signals. • A control system may consists of three elements for its block diagram. • They are 1. Block 2. Branch Point 3. Summing Point
- 51. • Block: • In a block diagram all the system variables are linked to each other through functional blocks. • The functional block or simply block is a symbol for the mathematical operation on the input signal to the block that produces the output. • The transfer function of a component is represented by a block. Block has single input and single output.
- 52. • Summing Points are used to add two or more signals in the system. • A Branch Point/Take off point is a point from which the signal from a block goes concurrently to other blocks or summing points.
- 53. Constructing Block Diagram for Control Systems • A control system can be represented diagrammatically by block diagram. • The Diff.Eqns governing the system are used to construct the block diagram. • By taking L.T the D.Eqns are converted to algebraic eqns. The eqns will have variables & constants. • From the working knowledge of the system the i/p and o/p variables are identified and the block diagram for each eqn can be drawn. • Each eqn gives one section of block diagram. The o/p of one section will be i/p to the other section. • The various sections are interconneced to obtain the overall block diagram of the system.
- 59. Block Diagram Reduction • The block diagram can be reduced to find the overall T.F of the system. • The following rules can be used for block diagram reduction . • The rules are framed such that any modification made on the diagram does not alter the input-output relation.
- 88. Signal Flow Graph(SFG) • The SFG is used to represent the control system graphically and it was developed by S.J.Mason. • A SFG is a diagram that represents a set of simultaneous linear algebraic eqns. • By taking L.T, the time domain D.Eqns governing a control system can be transferred to a set of algebraic eqns in s-domain. • The SFG & the block diagram approach yields the same information. • The advantage of SFG is that, using Mason’s gain formula the overall gain of the system can be computed easily.
- 89. • The SFG depicts the flow of signals from one point of system to another & gives the relationship among the signals. • A SFG consists of a n/w in which nodes are connected by directed branches. • Each node represents a system variable & each branch connected b/w two nodes acts as a signal multiplier. • Each branch has a gain or transmittance. When signal passing through a branch, it gets multiplied by the gain of the branch. • In SFG, the signal flows in only one direction. • The direction of signal flow is indicated by an arrow placed on the branch & the gain(multiplication factor) is indicated along the branch.
- 95. SFG Reduction • The SFG of a system can be reduced either by using rules of a SFG algebra or by using Mason’s Gain Formula. • For SFG reduction using rules of SFG, write eqns at every node and then rearrange these eqns to get the ratio of output & input.(T.F) • The SFG reduction by above method will be time consuming & tedious. • S.J.Mason has developed a simple procedure to determine the T.F of the system represented as a SFG. • He has developed a formula called by his name Mason’s gain formula which can be directly used to find the T.F of the system.
- 96. Mason’s Gain Formula • The Mason’s Gain Formula is used to determine the T.F of the system from the SFG of the system. • Let, R(s) = Input to the system C(s) = Output of the system Now, T.F of the system, T(s) = C(s)/R(s) • Mason’s Gain formula states the overall gain of the system (T.F) as follows, Overall Gain,
- 98. Constructing SFG for Control: • The following procedure can be used to construct SFG of a system. 1. Take L.T of the Diff.Eqns governing the system in order to convert them into s- domain. 2. The constants & variables of the s-domain equations are identified. 3. From the knowledge of the system, the variables are identified as input, output and intermediate variables. 4. For each variable a node is assigned in SFG and constants are assigned as the gain or transmittance of branches connecting the nodes. 5. For each eqn a SFG is drawn and then they are inrterconnected to give overall SFG of the system.
- 109. Procedure for converting Block Diagram to SFG • The following procedure can be used to convert Block diagram to SFG. 1. Assume nodes at i/p & o/p, at evry summing point, at every branch point and in between cascaded blocks. 2. Draw the nodes separately as small circles & number the circles in the order 1, 2, 3, …. 3. From the block diagram, find the gain b/w each node in the main forward path and connect all the corresponding ciclesby straight line and mark the gain b/w nodes. 4. Draw the feed forward paths b/w various nodes and mark the gain of feed forward path along with sign. 5. Draw the f/b paths b/w various nodes and mark the gain of feed forward path along with sign.
- 121. Electrical Analogous of Mechanical Translational Systems • The 3 basic elements Mass, Dash-pot and Spring that are used in modelling mechanical translational systems are analogous to Resistance, Inductance and Capacitance of electrical system. • The input Force in mechanical system is analogous to either voltage source or current source in electrical systems. • The output velocity in mechanical system is analogous to either current or voltage in an element in electrical system. • Since the electrical systems has two types of inputs either voltage or current source, they are two types of analogies: 1. Force-Voltage and 2. Force-current analogy.
- 142. Electrical Analogous of Mechanical Rotational Systems • The 3 basic elements moment of inertia, rotational dashpot and torsional spring are used in modelling mechanical systems are analogous to resistance, inductance and capacitance of electrical systems. • The i/p torque in mechanical system is analogous to either voltage or current sourse in electrical systems. • The o/p angular velocity in mechanical system is analogous to either current or voltage in an electrical system. • Since the electrical systems has two types of inputs either voltage or current, there are two types of analogies: Torque-Voltage and Torque-Current Analogy.