CE 6002 CONCRETE TECHNOLOGY UNIT II
- 1. DEPARTMENT OF CIVIL ENGINEERING CE 6002 – CONCRETE TECHNOLOGY G.GUNA S.R.V.E.C 1
- 2. Admixtures are the material, other than Cement Water Aggregates fiber reinforcement Which are used as an ingredient of concrete and is added to batch immediately before or during mixing. G.GUNA S.R.V.E.C 2
- 3. Admixtures have long been recognized as important components of concrete used to improve its performance. The original use of admixtures in cementitious mixtures is not well documented. G.GUNA S.R.V.E.C 3
- 4. G.GUNA S.R.V.E.C 4 The major reasons for using admixtures are: To reduce the cost of concrete construction. To achieve certain properties in concrete more effectively than by other means. To maintain the quality of concrete during the stages of mixing, transporting, placing, and curing in ad-verse weather conditions. To overcome certain emergencies during concreting operations.
- 5. Cost- Effective Durability Handling properties making placing compaction easier Permeabilit y freeze/thaw (air content) Consistence and sustainabili ty Density strength developme nt prevent shrinkage capacity for bleeding Reduce segregation bond of concrete to … impact and abrasion resistance colored concrete G.GUNA S.R.V.E.C 5
- 6. G.GUNA S.R.V.E.C 6 Each class of admixture is defined by its primary function. It may have one or more secondary functions, however, and its use may affect, positively or negatively, concrete properties other than those desired
- 7. 1. Chemical Admixtures 2. Mineral Admixtures G.GUNA S.R.V.E.C 7 Types of admixture for concrete
- 9. 1. Plasticizers 2. Super plasticizers 3. Retarders and Retarding Plasticizers 4. Accelerators and Accelerating Plasticizers 5. Damp-proofing and Waterproofing Admixtures G.GUNA S.R.V.E.C 9
- 10. In general, these chemicals act as dispersants for portland cement particles. By separating and spreading out the cement particles, internal friction is reduced, and slump and workability of the concrete is increased Lowering w/cm is a key method for improving durability G.GUNA S.R.V.E.C 10
- 11. The organic substances or combinations of organic and inorganic substances, which allow a reduction in water content for the given workability, or give a higher workability at the same water content, are termed as plasticizing admixtures. The basic products constituting plasticizers are as follows: Anionic surfactants such as lignosulphonates and their modifications and derivatives, salts of sulphonates hydrocarbons. Non ionic surfactants, such as polyglycol esters, acid of hydroxylated carboxylic acids and their modifications and derivatives. Other products, such as carbohydrates etc. G.GUNA S.R.V.E.C 11
- 12. 12G.GUNA S.R.V.E.C Amount used • A good plasticizer is one which does not cause air-entrainment in concrete more than 1 or 2%. • At constant workability – The reduction in mixing water is expected to be of the order of 5% to 15%. Naturally increases the strength. • At constant w/c ratio – Increased workability. Slump of 30mm to 150 mm. Results - effects Limitations • Plasticizers are used in the amount of 0.1% to 0.4% by weight of cement.
- 13. 13G.GUNA S.R.V.E.C Used at 1. Thin walls of water retaining structures with high percentage of steel reinforcement 2. Deep beams, column and beam junctions 3. Tremie concreting 4. Pumping of concrete 5. Hot weather concreting 6. Concrete to be conveyed for considerable distance and in ready mixed concrete industries. Where high degree of workability is required
- 14. Superplasticizers constitute a relatively new category and improved version of plasticizer, the use of which was developed in Japan and Germany during 1960 and 1970 respectively. They are chemically different from normal plasticisers. Classification of Superplasticizers: Sulphonated malanie-formaldehyde condensates (SMF) Sulphonated naphthalene-formaldehyde condensates (SNF) Modified lignosulphonates (MLS) Other types G.GUNA S.R.V.E.C 14
- 16. 16G.GUNA S.R.V.E.C Amount used Permits reduction of water content about 30% without reducing the workability It is possible to use w/c ratio as low as 0.25 or even lower and yet to make flowing concrete to obtain strength of order 120 Mpa or more. Results - benefits • Based on various types of superplasticizers different amount is used. • Lignosulphonates – not more than 0.25% • Carboxylic acids – 0.1% • Sulphonated malanie-formaldehyde condensates (SMF) – 0.5 to 3% • Sulphonated naphthalene-formaldehyde condensates (SNF) – 0.5 to 3%
- 17. 17G.GUNA S.R.V.E.C Used at Production of flowing, self levelling, self compacting concrete Production of high strength and high performance concrete. Superplasticizer is practiced for
- 18. A retarder is an admixture that slows down the chemical process of hydration so that concrete remains plastic and workable for a longer time than concrete without the retarder. 1. Retarders are used to overcome the accelerating effect of high temperature on setting properties of concrete in hot weather concreting. 2. Very useful when concrete has to be place in very difficult conditions and delay may occur in transporting and placing. 3. .Gypsum and Calcium Sulphate are well known retarders. 4. Other examples are: starches, cellulose products, sugars, acids or salts of acids G.GUNA S.R.V.E.C 18
- 19. 19G.GUNA S.R.V.E.C Limitations amount. Access Retarders should be used in proper amount will cause indefinite setting time. At normal temperatures addition of sugar 0.05 to 0.10 percent have little effect on the rate of hydration, but if the quantity is increased to 0.2 percent, hydration can be retarded to such an extent that final set may not take place for 72 hours or more. Casting and consolidating large number of pours without the formation of cold joints. Grouting oil wells, where temperature is about 200 °C, at a depth of 6000 meters. Used at
- 20. Accelerating admixtures are added to concrete to increase the rate of early strength development Why accelerators? 1. Permit earlier removal of formwork 2. Reduce the required period of curing 3. Advance the time that a structure can be placed in service 4. Partially compensate for the retarding effect of low temperature during cold weather concreting 5. In the emergency repair work. G.GUNA S.R.V.E.C 20
- 21. Commonly used materials as an accelerator: Calcium chloride (Not used now) Some of the soluble carbonates Silicates fluosilicates (Expensive) Some of the organic compounds such as triethenolamine (Expensive) G.GUNA S.R.V.E.C 21
- 22. Accelerators are so powerful that it is possible to make the cement set into stone hard in a matter of five minutes are less. With the availability of such powerful accelerator, the under water concreting has become easy. Similarly, the repair work that would be carried out to the waterfront structures in the region of tidal variations has become easy. The use of such powerful accelerators have facilitated, the basement waterproofing operations. G.GUNA S.R.V.E.C 22 Benefits of Accelerators
- 23. In practice one of the most important requirements of concrete is that it must be impervious to water under two conditions; Firstly, when subjected to pressure of water on one side. permeability-reducing admixture for hydrostatic conditions (PRAH) Secondly, to the absorption of surface water by capillary action. Permeabilityreducing admixture for non-hydrostatic conditions (PRAN). G.GUNA S.R.V.E.C 23
- 24. Waterproofing admixtures are available in powder, paste or liquid form and may consist of pore filling or water repellent materials. Chemically active pore filling materials: silicate of soda, aluminium/zinc sulphates and aluminium/calcium chloride. Chemically inactive filling material: chalk, fullers earth and talc. G.GUNA S.R.V.E.C 24
- 25. 25G.GUNA S.R.V.E.C Amount used Use of admixture should in no case be considered as a substitute for bad materials, bad design or workmanship. In no case can an admixture be expected to compensate for cracks or large voids in concrete causing permeability. Chemically active pore fillers accelerates the setting of concrete and thus render the concrete more impervious at early age. Chemically inactive pore fillers improve the workability and to facilitate the reduction of water for given workability and to make dense concrete which is basically impervious. Water repelling materials like soda, potash soaps, calcium soaps, waxes, fats, vegetable oils repel water and make the concrete impervious Results - effects Limitations Depends upon various damp-proofing and water proofing admixtures.
- 26. Pozzolanic materials are: Siliceous or siliceous-aluminous materials, Little or no cementitious value, In finely divided form and in the presence of moisture, Chemically react with calcium hydroxide liberated on hydration, at ordinary temperature, to form compounds, possessing cementitious properties. They are also known as POZZOLANIC materials. G.GUNA S.R.V.E.C 26
- 27. Improves many qualities of concrete, such as: Lower the heat of hydration and thermal shrinkage; Increase the water tightness; Reduce the alkali-aggregate reaction; Improve resistance to attack by sulphate soils and sea water; Improve extensibility; Lower susceptibility to dissolution and leaching; Improve workability; Lower costs. G.GUNA S.R.V.E.C 27
- 28. 28G.GUNA S.R.V.E.C Natural Pozzolans Clay and Shales Opalinc Cherts Diatomaceous Earth Volcanic Tuffs and Pumicites. Fly ash Blast Furnace Slag Silica Fume Rice Husk ash Metakaoline Surkhi Artificial Pozzolans
- 29. G.GUNA S.R.V.E.C 29 Fly ash is finely divided residue resulting from the combustion of powdered coal and transported by the flue gases and collected by; Electrostatic Precipitator Fly ash is the most widely used pozzolanic material all over the world.
- 30. 30G.GUNA S.R.V.E.C Class F Fly ash normally produced by burning anthracite or bituminous coal, usually has less than 5% CaO. Class F fly ash has pozzolanic properties only. Fly ash normally produced by burning lignite or sub-bituminous coal. Some class C fly ash may have CaO content in excess of 10%. In addition to pozzolanic properties, class C fly ash also possesses cementitious properties. Class C
- 31. 31G.GUNA S.R.V.E.C Amount used Reduction of water demand for desired slump. With the reduction of unit water content, bleeding and drying shrinkage will also be reduced. fly ash is not highly reactive, the heat of hydration can be reduced through replacement of part of the cement with fly ash. Results - effects • Up to 35% by mass of cement (According to IS: 456 – 2000) & minimum shall not be less than 15%.
- 32. . • Use of fly ash is because of many factors such as: a) Abundance of fly ash b) Fly ashes from major TPP(Trans-Pacific Partnership) are of very high quality i.e. quality of fly ash. c) Economic factor i.e. Cost of fly ash with in 200 km from a TPP is as low as 10% to 20% of the cost of cement. d) Environmental factors i.e. reduction in CO2 emission. HVFAC is a concrete where excess of 35%of fly-ash is used as replacement G.GUNA S.R.V.E.C 32
- 33. 33G.GUNA S.R.V.E.C Effects of Fly Ash on Hardened Concrete contributes to the strength of concrete due to its pozzolanic reactivity. continued pozzolanic reactivity concrete develops greater strength at later age not at initial stage. contributes to making the texture of concrete dense, resulting in decrease of water permeability and gas permeability.
- 34. 34G.GUNA S.R.V.E.C Used at Many high-rise buildings Industrial structures Water front structures Concrete roads Roller compacted concrete dams.
- 35. G.GUNA S.R.V.E.C 35 The transition zone is a thin layer between the bulk hydrated cement paste and the aggregate particles in concrete. This zone is the weakest component in concrete, and it is also the most permeable area. Silica fume plays a significant role in the transition zone through both its physical and chemical effects. 1. fine micro-crystalline silica produced in electric arc furnaces as a by product. 2. Very fine non-crystalline silica produced in electric arc furnaces as a by product.
- 36. It is a product resulting from reduction of high purity quartz with coal in an electric arc furnace in the manufacture of silicon or ferrosilicon alloy. 1. Micro silica is initially produced as an ultrafine undensified powder 2. At least 85% SiO2 content 3. Mean particle size between 0.1 and 0.2 micron 4. Minimum specific surface area is 15,000 m2/kg 5. Spherical particle shape G.GUNA S.R.V.E.C 36
- 37. Micro silica is available in the following forms: 1. Undensified forms with bulk density of 200–300 kg/m3 2. Densified forms with bulk density of 500–600 kg/m3 3. Micro-pelletised forms with bulk density of 600–800 kg/m3 4. Slurry forms with density 1400 kg/m3 5. Admixtures and Construction Chemicals. 6. Slurry is produced by mixing undensified micro silica powder and water in equal proportions by weight. Slurry is the easiest and most practical way to introduce micro silica into the concrete mix. 7. Surface area 15–20 m2/g. 8. Standard grade slurry pH value 4.7, specific gravity 1.3 to 1.4, dry content of micro silica 48 to 52%. G.GUNA S.R.V.E.C 37
- 38. 38G.GUNA S.R.V.E.C Effect on fresh concrete The increase in water demand of concrete containing microsilica will be about 1% for every 1% of cement substituted. lead to lower slump but more cohesive mix. make the fresh concrete sticky in nature and hard to handle. large reduction in bleeding and concrete with microsilica could be handled and transported without segregation. to plastic shrinkage cracking and, therefore, sheet or mat curing should be considered. produces more heat of hydration at the initial stage of hydration. the total generation of heat will be less than that of reference concrete.
- 39. 39G.GUNA S.R.V.E.C nano silica The 2% nano silica is the optimum content that exhibited highest compressive strength at 7 and 28 days among all nano silica contents The rate of strength development indicates that the mortars containing nano silica, being more reactive and contributes more to the compressive strength at 7 days than 28 days. The addition of 2% NS increased the early age compressive strength (i.e. 3 days) of HVFA concrete containing 60% fly ash by about 95%. However, no such improvement is noticed at other ages. The use mechanical dry mixing of nano silica with cement, fly ash and sand performed better than ultrasonic mixing of NS with water and superplasticizer BSE image analysis shows that the addition of 2% nano silica significantly improves the microstructure of the matrix of high volume fly ash mortars. The XRD results also confirm this result where the addition of 2% nano silica reduces the calcium hydroxide by about 58% and 50% in high volume fly ash mortars containing 40% and 60% fly ash, respectively
- 40. 40G.GUNA S.R.V.E.C Backscattered electron (BSE) images of polished surface of paste samples after 28 days of curing: (a) cement paste, (b) paste containing 40% fly ash, (c) paste containing 60% fly ash, (d) paste containing 2% NS, (e) paste containing 38% fly ash and 2% NS and (f) paste containing 58% fly ash and 2% NS.
- 41. 41G.GUNA S.R.V.E.C Effect on hardened concrete 1. Modulus of elasticity of microsilica concrete is less. 2. Improvement in durability of concrete. 3. Resistance against frost damage. 4. Addition of silica fume in small quantities actually increases the expansion. 5. Conserve cement 6. Produce ultra high strength concrete of the order of 70 to 120 Mpa. 7. Increase early strength of fly concrete. 8. Control alkali-aggregate reaction. 9. Reduce sulfate attack & chloride associated corrosion.
- 42. 42G.GUNA S.R.V.E.C Rice husk ash is obtained by Burning rice husk in a controlled manner without causing environmental pollution. Material of future as mineral additives.
- 43. 43G.GUNA S.R.V.E.C Amount used 10% by weight of cement. It greatly enhances the workability and impermeability of concrete. Amorphous silica (90% SiO2) in very high proportion when burnt in controlled manner. 5% carbon. 2% K2O. Contains
- 44. 44G.GUNA S.R.V.E.C Effects Reduces susceptible to acid attack and improves resistance to chloride penetration. Reduces large pores and porosity resulting very low permeability. Reduces the free lime present in the cement paste. Decreases the permeability of the system. Improves overall resistance to CO2 attack. Enhances resistance to corrosion of steel in concrete. Reducing micro cracking and improving freeze-thaw resistance. Improves capillary suction and accelerated chloride diffusivity.
- 45. G.GUNA S.R.V.E.C 45 Blast-furnace slag is a nonmetallic product consisting essentially of silicates and aluminates of calcium and other bases. The molten slag is rapidly chilled by quenching in water to form a glassy sand like granulated material. The granulated material when further ground to less than 45 micron will have specific surface of about 400 to 600 m2/ kg (Blaine).
- 46. G.GUNA S.R.V.E.C 46 Highly reactive metakaolin is made by water processing to remove unreactive impurities to make100% reactive pozzolan. Such a product, white or cream in colour, purified, thermally activated is called High Reactive Metakaolin (HRM).
- 47. G.GUNA S.R.V.E.C 47 the synergy of cement and metakaolin tends to reduce the pore size to about a tenth of the diameter within the first days. This is valid to a replacement until the 20% level and about 27% water in which most of the Portlandite formed will have reacted to form additional CSH* or CSAH** phases. Through the formation of these phases the pores will be filled by additional binding material. Due to the lower pores diameter the water uptake is reduced. The total pore volume depends on the w/b ratio***. With very high porosity the advantages of metakaolin replacement will decrease.
- 48. 48G.GUNA S.R.V.E.C Effects of Metakaolin High reactive metakaolin shows high pozzolanic reactivity and reduction in Ca(OH)2 even as early as one day. The cement paste undergoes distinct densification. Densification includes an increase in strength and decrease in permeability. The high reactive metakaolin is having the potential to compete with silica fume. Use of Metakaolin