![when the supply is dc:
Chopper control
9. How is the stator winding changed during constant torque and constant
horsepower operations?
For constant torque operation, the change of stator winding is made form
series - star to parallel - star, while for constant horsepower operation the change
is made from series-delta to parallel-star. Regenerative braking takes place during
changeover from higher to lower speeds.
10.Define positive and negative motor torque.
Positive motor torque is defined as the torque which produces acceleration or
the positive rate of change of speed in forward direction. Positive load torque is negative
if it produces deceleration.
11.Write the expression for average o/p voltage of full converter fed dc drives?
Vm=(2Vm/pi)cospi.........continuous conduction
Vm=[Vm(cos alpha-cos beta)+(pi+alpha+beta)]/pi] discontinuous conduction
12.What are the disadvantages of conventional Ward-Leonard schemes?
Higher initial cost due to use of two additional
mcs. Heavy weight and size.
Needs more floor space and proper foundation. Required frequent maintenance
13.Mention the drawbacks of rectifier fed dc drives?
Distortion of supply.
Low power factor.
Ripple in motor current
14.What are the advantages in operating choppers at high frequency?
The operation at a high frequency improves motor performance by reducing
current ripple and eliminating discontinuous conduction.
15.Why self commutated devices are preferred over thyristors for chopper circuits?
Self commutated devices such as power MOSFETs power transistors, IGBTs,
GTOs and IGCTs are preferred over thyristors for building choppers because they can
be commutated by a low power control signal and don't need commutation circuit.
16.State the advantages of dc chopper drives?
DC chopper device has the advantages of high efficiency, flexibility in control,
light weight, small size, quick response and regeneration down to very low speed.](https://image.slidesharecdn.com/unit-2-230120172126-b4a7c25d/85/Unit-2-pdf-14-320.jpg)
![ There is considerable savings in energy and thus it is economical method as
compared to other methods of speed ctrl.
27.What is meant by soft start?
The ac voltage controllers show a step less control of supply voltage from zero to
rated voltage they are used for soft start for motors.
28.List the adv of squirrel cage IM?
Cheaper
light in weight
Rugged in construction
More efficient
Require less maintenance
It can be operated in dirty and explosive environment
29.Define slip
The difference between the synchronous speed (Ns)and actual speed(N)of the
rotor is known as slip speed. the % of slip is gn by,
%slip s=[(Ns-N)/Ns]x 100
30.Define base speed.
The synchronous speed corresponding to the rated freq is called the base speed.](https://image.slidesharecdn.com/unit-2-230120172126-b4a7c25d/85/Unit-2-pdf-16-320.jpg)
Unit-2..pdf
- 1. UNIT II CONVERTER / CHOPPER FED DC MOTOR DRIVE Single Phase Fully Controlled Converter Fed Separately Excited D.C Motor Drive Fig 2.1 The basic circuit for a single-phase separately excited dc motor drive is shown in Fig. 2.1.The armature voltage is controlled by a semi-converter or full-converter and the field circuit is fed from the ac supply through a diode bridge. The motor current cannot reverse due to the thyristors in the converters. If semi-converters are used, the average output voltage (Ea)is always positive. Therefore power flow (Ea1a) is always positive, that is, from the ac supply to the dc load. In drive system semi-converters, regeneration or reverse power flow from motor to ac supply is not possible. In semi-converters free- wheel (i.e., dissipation of armature i n d u c t a n c e energy through the free-wheeling path) takes place when the thyristor blocks. Single-phase full-wave d r i v e s are used for low and medium-horsepower applications as indicated infig2.1.Suchdriveshavepoor speed regulation on open-loop firing angle control. However, with armature voltage or tachometer feedback, good regulation can be achieved. Basic Equation I The armature circuit of the de motor is represented by its back voltage eg, armature resistance Ra, and armature inductance LaasshowninFig.2.1. Back voltage: (1)
- 2. Average Back Voltage (2) Developed torque: (3) Average developed torque: (4) The armature circuit voltage equation is (5)
- 3. Interms of average values, (6) Note that the inductance La does not absorb any average voltage. From eequation 2 and 6, the average speed is In single-phase converters, the armature voltage ea and current t, change with time. This is unlike the M-G set drive in which both ea and t, are essentially constant. In phase-controlled converters, the armature current ia may not even be continuous. In fact, for most operating conditions, t, is discontinuous. This makes prediction of performance difficult. Analysis is simplified if continuity of armature current can be assumed. Analysis for both continuous and discontinuous current is presented in the following sections Continuous Armature Current Let us assume that the armature current is continuous over the whole range of operation. Typical voltage and current waveforms are shown in Figs.2.2 and 2.3 for semi-converter and full-converter systems, respectively. The thyristors are symmetrically triggered. In the semi-converter systemshowninFig.2.2, thyristor Sl is triggered at an angle a and S2atan anglea+7T with respect to the supply voltage v. In the full-converter systemshowninFig.2.3, thyristors S1, and S3 are simultaneously triggered at a, thyristors S2andS4aretriggeredat7T +a. In Fig. 2.2, the motor is connected to the input supply for the period a<wt<7T through Sl and D2, and the motor terminal voltage ea is the same as the supply input voltage v. Beyond 7T, ea tends to reverse as the input voltage changes polarity. This will forward-bias the free-wheeling diode and DFW w i l l start conducting. The motor current ia, which was flowing from the supply through Sl' is transferred to DFW (i.e., Sl commutates). The motor terminals are shorted through thefree-wheelingdiodeduring7T <wt <(7T +a), making zero. Energy from the supply is therefore delivered to the armature Circuit when the thyristor conducts (a to7T). This energy is partially stored in the inductance, partially stored in the kinetic energy (K.E.) of the moving system, and partially used to supply the mechanical load. During the free-wheeling period, 7T to7T +a, energy is recovered from the inductance and is converted to mechanical form to supplement the K.E.in supplying the mechanical load. The free- wheeling armature current continues to produce electromagnetic torque in the motor. No energy is feedback to the supply during this period.
- 4. In Fig.2.3, the motor is always connected to the input supply through the thyristors. Thyristors Sl and S3conduct during the interval a<wt <(7T +a) and connect the motor to the supply. At 7T +a, thyristors S2 and S4aretriggered.Immediately the supply voltage appears across the thyristors Sl and S3asareverse- bias voltage and turns them off. This is called natural or line commutation. The motor current Ia, which was flowing from the supply through Sl and S3'istransferred toS2and S4.During ato7T, energy flows from the input supply to the motor (both v and Ia repositive, and eo and io are positive, signifying positive power flow). However, during 7T to 7T +a, some of the motor system energy is feedback to the input supply(v and I have opposite polarities and likewise ea and io' signifying reverse power flow). In Fig.2.3c voltage and current waveforms are shown for a firing angle greater than 90°.The average motor terminal voltage Eo is negative. If the motor back emf Eg is reversed, it will behave as a de- generator and will feed power back to the ac supply. This is known as the inversion operation of the converter, and this mode of operation is used in the regenerative
- 5. braking of the motor. Torque Speed Characteristics For a semi-converter with free-wheeling action the armature circuit equations are: Single-Phase Separately Excited DC Motor Drives The armature circuit equation for a full-converter is:
- 6. DISCONTINUOUS ARMATURE CURRENT The torque-speed characteristics shown in Fig.2.4b are drawn on the crude assumption that the armature current is continuous over the whole range of operation. It is very doubtful that the armature current will be continuous at high values of the firing angle a, high speed, and low values of torque. In fact, armature current is discontinuous for these operating conditions. If the armature current is discontinuous, the no-load speeds will be higher than those shown in Fig.2.4b, and the speed regulation will be significantly poor in the region of discontinuous armature current. The motor performance
- 7. . I The waveforms with semi-converter and full-converter w i t h discontinuous armature current areshowninFig.2.5andFig.2.6, respectively. In Fig. 2.5, the motor is connected to the input supply for the period a<wI <71' through S, and Dz.Beyond 71', the motor terminal is shorted through the free-wheeling diode DFW' The armature current decays to zero at before the thyristor S2 is triggered at71' +a, thereby making the armature current discontinuous. During a to 71' (i.e., the conduction period of the
- 8. thyristor S,), motor terminal voltage ea is the same as the supply voltage v. However, during the motor current free-wheels through DFW and so ea s zero. The motor coasts and the motor terminal voltage ea is the same as the back voltage InFig.2.6, the motor is connected to the supply during a<wt<{3 and it Coasts during {3<wI <71' +a. As long as the motor is connected to the supply, its terminal voltage is the same as the input supply voltage. If the armature current can be assumed to be continuous, the torque-speed characteristics can be calculated merely from average values ofthe motor terminal voltage and current. In the discontinuous current mode, these calculations are cumbersome. The difficulty arises in the calculation of the average motor terminal voltage Ea, because (called the extinction angle, the instant at which the thyristor or motor current becomes zero) depends on, the average speed N, average armature current la' and the firing angle a. A general approach, valid for both continuous and discontinuous armature current, is therefore necessary. Three Phase Fully Controlled Converter Fed Separately Excited D.C Motor Drive Three phase controlled rectifiers are used in large power DC motor drives. Three phase controlled rectifier gives more number of voltage per cycle of supply frequency. This makes motor current continuous and filter requirement also less. The number of voltage pulses per cycle depends upon the number of thyristors and their connections for three phase controlled rectifiers. In three phase drives, the armature circuit is connected to the output of a three phase controlled rectifier. Three phase drives are used for high power applications up to megawatts power level. The ripple frequency of armature voltage is greater than that of the single phase drives and its requires less inductance in the armature circuit to reduce the armature current ripple Three phase full converter are used in industrial application up to 1500KW drives. It is a two quadrant converter. Principle of Operation
- 9. Three phase full converter bridge circuit connected across the armature terminals is shown fig. The voltage and current waveforms of the converter. The circuit works as a three AC to DC converter for firing angle delay 00 < α < 900 and as a line commutated inverter for 900 < α < 1800 . A three full converter fed DC motor is performed where generation of power is required.
- 10. Four Quadrant Operation of a Converters The bi-directional boost converter is the IPQC version of the conventional thyristor dual converters. Their topology is derived from ac-ac matrix converters using four quadrant switches (4QSWs). Since no four-quadrant switch is currently commercially available the realized by embedding a transistor inside a diode bridge or by inverse parallel connections of transistors as shown in Fig (1). Power IGBT employed because they have the advantage so high switching frequency and small pulse and notch widths. Topology of a single-phase bi-directional boost converter using typeI 4QSWsis shown in Fig(2). In the circuit shown in Fig (2), here are four4QSWs, two in each limb. Each 4QSW comprises two 2QSWs (two quadrant switches), each two-quadrant switch consisting of a IGBTT with series diode, connected in inverse-parallel. The operation of the bi-directional boost converter in boost
- 11. mode and in a particular quadrant in the V-I plane shown in Fig (3) is determined by the conditioning of the switching states of two sets (I and II) of devices. In the single-phase version each set comprises four IGBTs; set(A) IGBTs–T11,T22,T33,T44 and set(B)I GBTTs- T1,T2,T3,T4.corresponding to the four quadrants in the buck and boost modes pertaining to the rectification and inversion operations
- 12. Time Ratio Control (TRC) In this control scheme, time ratio Ton/T (duty ratio) is varied. This is realized by two different ways called Constant Frequency System and Variable Frequency System as described below: Constant Frequency System In this scheme, on-time is varied but chopping frequency f is kept constant. Variation of Ton means adjustment of pulse width, as such this scheme is also called pulse-width-modulation scheme. Variable Frequency System In this technique, the chopping frequency f is varied and either (i) on-time Ton is kept constant or (ii) off-time Toff is kept constant. This method of controlling duty ratio is also called Frequency- modulation scheme. Current- Limit Control In this control strategy, the on and off of chopper circuit is decided by the previous set value of load current. The two set values are maximum load current and minimum load current. When the load current reaches the upper limit, chopper is switched off. When the load current falls below lower limit, the chopper is switched on. Switching frequency of chopper can be controlled by setting maximum and minimum level of current. Current limit control involves feedback loop, the trigger circuit for the chopper is therefore more complex. PWM technique is the commonly chosen control strategy for the power control in chopper circuit
- 13. UNIT – II TWO MARKS 1. What is the use of flywheel? Where it is used? It is used for load equalization. It is mounted on the motor shaft in compound motor. 2. What are the advantages of series motor? The advantages of series motors are, High starting torque Heavy torque overloads. 3. Define and mention different types of braking in a dc motor? In breaking the motor works as a generator developing a negative torque which opposes the motion. Types are regenerative braking, dynamic or rheostat braking and plugging or reverse voltage braking. 4. How the D.C. motor is affected at the time of starting? A D.C. motor is started with full supply voltage across its terminals, a very high current will flow, which may damage the motor due to heavy sparking at commuter and heating of the winding. Therefore, it is necessary top limit the current to a safe value during starting. 5. List the drawbacks of armature resistance control? In armature resistance control speed is varied by wasting power in external resistors that are connected in series with the armature. since it is an inefficient method of speed control it was used in intermittent load applications where the duration of low speed operations forms only a small proportion of total running time. 6. What is static Ward-Leonard drive? Controlled rectifiers are used to get variable d.c. voltage from an a.c. source of fixed voltage controlled rectifier fed dc drives are also known as static Ward-Leonard drive. 7. What is aline commutated inverter? Full converter with firing angle delay greater than 90 deg. is called line commutated inverter. such an operation is used in regenerative braking mode of a dc motor in which case a back emf is greater than applied voltage. 8. Mention the methods of armature voltage controlled dc motor? When the supplied voltage is ac, Ward-Leonard schemes Transformer with taps and un controlled rectifier bridge Static Ward-Leonard scheme or controlled rectifiers
- 14. when the supply is dc: Chopper control 9. How is the stator winding changed during constant torque and constant horsepower operations? For constant torque operation, the change of stator winding is made form series - star to parallel - star, while for constant horsepower operation the change is made from series-delta to parallel-star. Regenerative braking takes place during changeover from higher to lower speeds. 10.Define positive and negative motor torque. Positive motor torque is defined as the torque which produces acceleration or the positive rate of change of speed in forward direction. Positive load torque is negative if it produces deceleration. 11.Write the expression for average o/p voltage of full converter fed dc drives? Vm=(2Vm/pi)cospi.........continuous conduction Vm=[Vm(cos alpha-cos beta)+(pi+alpha+beta)]/pi] discontinuous conduction 12.What are the disadvantages of conventional Ward-Leonard schemes? Higher initial cost due to use of two additional mcs. Heavy weight and size. Needs more floor space and proper foundation. Required frequent maintenance 13.Mention the drawbacks of rectifier fed dc drives? Distortion of supply. Low power factor. Ripple in motor current 14.What are the advantages in operating choppers at high frequency? The operation at a high frequency improves motor performance by reducing current ripple and eliminating discontinuous conduction. 15.Why self commutated devices are preferred over thyristors for chopper circuits? Self commutated devices such as power MOSFETs power transistors, IGBTs, GTOs and IGCTs are preferred over thyristors for building choppers because they can be commutated by a low power control signal and don't need commutation circuit. 16.State the advantages of dc chopper drives? DC chopper device has the advantages of high efficiency, flexibility in control, light weight, small size, quick response and regeneration down to very low speed.
- 15. 17.What are the advantages of closed loop c of dc drives? Closed loop control system has the adv. of improved accuracy, fast dynamic response and reduced effects of disturbance and system non-linearities. 18.What are the types of control strategies in dc chopper? Time ratio control. Current limit control. 19.What are the adv. of using PI controller in closed loop ctrl. of dc drive? Stabilize the drive Adjust the damping ratio at the desired value Makes the steady state speed error close to zero by integral action and filters out noise again due to the integral action. 20.What are the different methods of braking applied to the induction motor? Regenerative braking Plugging, Dynamic braking. 21.What are the different methods of speed control of IM? Stator voltage control, Supply frequency control, Rotor resistance control, Slip power recovery control. 22.What is meant by stator voltage control.? The speed of the IM can be changed by changing the stator voltage. Because the torque is proportional to the square of the voltage. 23.Mention the application of stator voltage control. This method is suitable for applications where torque demand reduced with speed, which points towards its suitability for fan and pump drives. 24.Mention the applications of ac drives. AC drives are used in a no. of applications such as fans, blowers, mill run-out tables, cranes, conveyors, traction etc. 25.What are the three regions in the speed-torque characteristics in the IM? Motoring region (0<=s<=1) Generating region(s<0) Plugging region (1<=s<=2) where s is the slip. 26.What are the advantages of stator voltage control method? The control circuitry is simple Compact size Quick response time
- 16. There is considerable savings in energy and thus it is economical method as compared to other methods of speed ctrl. 27.What is meant by soft start? The ac voltage controllers show a step less control of supply voltage from zero to rated voltage they are used for soft start for motors. 28.List the adv of squirrel cage IM? Cheaper light in weight Rugged in construction More efficient Require less maintenance It can be operated in dirty and explosive environment 29.Define slip The difference between the synchronous speed (Ns)and actual speed(N)of the rotor is known as slip speed. the % of slip is gn by, %slip s=[(Ns-N)/Ns]x 100 30.Define base speed. The synchronous speed corresponding to the rated freq is called the base speed.