User guide
Download as DOCX, PDF0 likes288 views
This document provides instructions for operating and maintaining a Yamaha FZ 16 motorcycle. It outlines key components such as the chassis, suspension, brakes, instruments, and controls. It describes the functions of the tachometer, switches, and displays. Finally, it lists important maintenance tasks such as checking the fuel lines, plugs, air filter, battery, brakes, wheels, tires, chain, and lubricating moving parts.
User guide
- 1. USER GUIDE MEMBERS: GIOVANNY ANDRES QUINTERO S. CRISTIAN CAMILO VELEZ. ARBID MUÑOZ Z CEFIT ENVIGADO 2012
- 3. SUMARY 1) Security and comfort 2) Instruments and controls 3) Instruction for operating 4) Service and maintenance
- 4. SECURITY AND CONFORT Motorcycles are two-wheeled vehicles. Safety of its use and operation depends on proper driving techniques, as well as the skill of the driver conductor. All requirements should be knew by the driver before driving a motorcycle. complete instructions from a competent source on all aspects of motorcycle observe the warnings and maintenance and requirements contained in the manual obtain qualified information on safe driving techniques and appropriate get professional technical service according to the manual or when conditions so require Mechanical
- 5. SHASIS: the chassis meets two basic types of functions Static = CHASSIS must support the weight of the rider and passenger of motorcycle, the engine and transmission and devices such as oil and gas. Dynamics: the CHASSIS and the rest of the bike (wheels and suspension) together must provide precise steering, good handling and good grip comfort SUSPENCION: basically a suspension has two main functions: to keep the wheels in contact with the ground at all the time. ensure that the parts on the bike are anchored to the wheels and fixed all parts to it.
- 6. BRAKES: It works by decreasing the speed of the vehicle by means of friction between two or more pieces that are usually steel and shims or synthetic or metallic pads INSTRUMENTS AND CONTROL AND INSTRUMENTS FOR OPERATING TACHOMETER Switch 'locking main direction controls the ignition and lighting systems, and is used to lock the steering. Below describes the following different positions Open: All electrical circuits are energized Closed: All electrical systems are off you can remove the key
- 7. closed lock: The steering is locked, and all electrical systems are off Indicator light beam. This warning light is turned on, when the high beam of the lamp is on. Shift indicator light: This indicator light flashes when the turn signal switch pushed to the left or right. neutral spot light this light comes on when the transmission Is in neutral position. The electric tachometer allows the rider to monitor engine rpm and keep them within the power range to turn the key in the position "on" the tachometer sweep once across the rpm range and then returns to 0 rpm to test entire electrical circuit the multifunction display is provided by elements following models: a speedometer an odometer fuel meter Switch, turn signal: to signal a right turn puts the switch in this position, to signal a left turn, push the switch to that position. Step light switch: press this switch to make light work of passage.
- 8. Light switch crossing road: this interrupter position to put up the beam and put down for beam Horn switch: Press this switch to sound the horn SERVICE AND MANTENANCE FUEL LINES: check if the fuel hoses for cracks PLUG: Check condition, clean and adjust tolerance AIR FILTER: cleaning, change BATTERY: check the output voltage, check the electrolyte CLUTCH: verify operation adjust, lubricate the lever FRONT BRAKE: check function, fluid level and leaks, changing brake pads. REAR BRAKE: Check operation of the brake pads, check for damaged Brake hose: replace if necessary WHEELS: Check run out and for damage. TIRES: check tread depth and are not cracks. Change if necessary, check the air pressure. PADS WHEEL: check whether the cushions are loose or damaged Swing arm: Check operation and change the clearance is excessive grease lubricated bushings. CHAIN DRIVE: check clearance alignment and adjustment status and lubricate chain with a chain lubricant.
- 9. PADS ADDRESS: check clearance cushions and steering for tough grease lubricated. FRAME MOUNTING: check that all bolts are properly tightened nuts. SIDESTAND CENTRAL: Check operation and lubricate. FRONT FORK: Check operation and for oil leakage. SHOCK SET: Check operation and for oil leakage. MOTOR OIL: Change oil level and check for leaks. ENGINE OIL FILTER: change. MOBILE PARTS AND CABLES: lubricate. BOX throttles grip and cable: Check operation and free play, adjust the clearance of the cable if necessary. SIDESTAND CENTRAL: check if the air shutoff valve, the reed valve and the air tube change damaged parts are damaged. FRONT FORK: check operation, adjust the headlight.