User manual of advanced controller
0 likes1,581 views
This document provides installation and operation instructions for a wind/solar hybrid controller model SSWC-06-1224-TA. Key points include: 1. The controller can be used for 200-600W wind turbines and 12V/24V battery systems. It has protection functions and MPPT charging. 2. Connection instructions are provided for the wind turbine, solar panels, battery, and loads. Parameters like voltage thresholds can be configured via the LCD display. 3. Operation modes for the two output lines can be set, including constant power, half power, and turn off times. Technical specifications and warranty information are also included.
User manual of advanced controller
- 1. Page - 1 - of 9 200W-600 W series Model no.: SSWC-06-1224-TA Version：2011-5.0ver
- 2. Page - 2 - of 9 Notes Thank you for ordering our controller. Please read manual carefully before installation and keep it properly. To make this model running properly, installation should be strictly in accordance with manual and done by experienced technicist Please use insolating tool to install this machine, don‟t use bad tools. Please don‟t use low quality battery to avoid leakage, rust or burn. Please don‟t use thin or low quality cable to avoid leakage or fire. Do not open cover and maintain personally. Please don‟t reverse battery anode and cathode, don‟t reverse solar panel anode and cathode. Keep it away from moist, rain, insolation, severe dust, shaking, corrosion and Intensive or under intense electromagnetic interference. Do not install or use this machine in an environment mixed with combustible gas. This machine prohibited around the place with any flammable, explosive and dangerous goods. Keep any symbols on the controller complete. To avoid accidents, keep it away from this children.
- 3. Page - 3 - of 9 1. General Description The advanced wind/solar hybrid controller is specially designed for high-end small-scale wind/solar hybrid system and especially suitable for wind/solar hybrid street light system and wind/solar hybrid monitoring system. 2. Product feature Independent Boost Circuit: Solved the charging efficiency of the low-power vertical wind generator MPPT charging way, make sure power max. input to battery and high charging efficiency obtained. Be able to use for 200W-600W wind turbine with high compatibility. 12V/24V System Automatic Recognition function. Allow to connection reversely by battery or solar panel positive negative polarity. Mini-size, be easy to install. RS232 data communication with computer (we supply software) 3. Protection Functions Solar cells reverse charging, solar cells anti-reverse connection Battery over-charging, battery over-discharge, battery anti-reverse connection. Over-load, load anti-reverse connection. Wind turbine current and voltage limited, rotation limited, dump-load to brake. 4. Controller output DC power illumination This device be able to do following 2 design output type, please request which type are your expectation before buy. * NOW, YOUR CHOICE TYPE IS √ ITEM. (I) 1th and 2nd line output are all 24hours constant DC power for monitor system. Please ignore below about lighter or timer setting, this function was invalidation. (II) 1th and 2nd line output are: full power + half power + turn off + morning lighting 5. Time setting illumination (setting way please refer to item9.) “T1-X ”mean 1th line output,“T2-X”mean 2nd line output（for example T1-X） T1-1 ：default value be 5 , mean full-power time is 5hours,then go intoT1-2 step. T1-2 ：default value be 3 , mean half- power time is 3hours,then go intoT1-3 step. T1-3 ：default value be 3 , mean turn off time is 3hours,then go intoT1-4 step. T1-4 ：this process is balance of whole night time. And turn off lamp while day. This value would not show T1-1 full power T1-2 half power T1-3 turn off T1-4 morning lighting Night – turn on Day- turn offBy light sensor
- 4. Page - 4 - of 9 S on LCD, so this value is not adjustable. Of course , you could to cover this process by -2,-3 value with longer time. 6. Model Description After installing wind wind/solar hybrid system, please connect the controller accurately as the sequential operation. 7. Connection process Graph 2, terminal connection Graph 1, wind&solar hybrid system Picture 1, wind&solar hybrid system wiring Picture 1, wind&solar hybrid system wiring Picture 1, wind&solar hybrid system wiring Company code S W C-06-1224 -TA Battery vol. 12V/24V auto Wind turbine power 600W controller（Controller） wind（Wind Energy） solar（Solar Energy） Top advanced
- 5. Page - 5 - of 9 Please connect and operate system components strictly according to the steps below! （I） Connect with Battery： 1. Connect accumulate battery wire to “BATTERY” terminal which rear of device. Please use the cuprum cable which about 6mm2 and less than 1m. Although the machine has reverse connection protection, it is forbiden connecting the battery reversely ! After installing battery, this led will be twinkling approximate15 seconds once connected with battery for device initial working. （II） Connect with wind turbine： Ensure wind turbine in brake status and then connect the wind turbine output lines to the “WIND INPUT” terminals in back panel . （III）Connect with solar panel： If your system have solar panel, please connect the wire to “SOLAR INPUT” terminal rear of device. Connection reversely is prohibited ! （IV）Connect with DC output： Connect DC load to “DC OUTPUT” terminal : The first load should be connected to "+" and "-1" of the “DC OUTPUT” terminals , The second load should be connected to "+" and "-2" of the “DC OUTPUT” terminals. The modes of load output can be setted according to the requirements of system .( The
- 6. Page - 6 - of 9 half-power output is only applicable to LED light ). 8. LCD Display Instructions LCD backlight is on after pressing any key. The backlight will auto-off 10 seconds later to save power while stop pressing any key. A) Description of Key-Press: （+）key: key symbolizes increase or next one. In browsing window, press this key to check next parameter. In setting window, press this key to check next adjustable parameter or increase the value of the current parameter. （—）key: key symbolizes decrease or previous one. In browsing window, press this key to check the previous parameter. In setting window, press this key to check the previous adjustable parameter or decrease the value of the current parameter. B) Displayed Content Description: LCD screen displays the following picture after turned on: Press (-) key to next page: 9. System parameters setting Instructions “ENTER” key：symbolizes set or confirm: press this key to access setting window. In setting window, press this key to choice each parameter and go to next page. “Esc” key: cancel or manual switch. In setting window, press this key to return to browsing window and do not save the modified parameters. Press “ENTER” to access following display of screen firstly. Vd1： Battery over-discharge voltage Vdr1：Battery over- discharge recovery voltage Vu1： Battery over-charge voltage Vur1： Battery over-charge recovery voltage Vdl：21.0V Vdrl：25.0V Vul：28.8V Vurl：26.5V Uw: 20.8V Us: 28.6V Ub: 24.5V Iw： 05.0A Uw: wind-turbine voltage Us: Solar panel voltage Ub: battery voltage Iw： charging current of wind-turbine Is: 10.5A STA: Normal D/N: Day E-b: 76% Is： charging current of solar panel STA： system status D/N： show“DAY” or“Night” E-b： power volume of battery
- 7. Page - 7 - of 9 Press “ENTER” key again to choose, Press (+) key or (-) key to adjust the value, each press means increase or reduce 0.1V Press “ENTER” key to next page: Press “ENTER” to choose, Press (+) key or (-) key to adjust the value, each press means increase or reduce 0.1V, each press means increase or reduce 1 hour while setting time Press “ENTER” key to next page: Press “ENTER” to choose, Press (+) key or (-) key to adjust the number, each press means increase or reduce 0.1V, each press means increase or reduce 1 hour while setting time Press “ENTER” key to next page: Remind! This parameter must be modify by professional technician, general user re-setting is prohibited! Press “ENTER” key to next page: Press “ENTER” key to save value set, and access to setting window again. Press “ESC” key do not save value set and access to browsing window. Remind! Vf1: Wind-turbine dump protection voltage T1-1: Line1 whole power output time T1-2: Line1 half-power output time T1-3: Line1 Turn-off output time T2-1: Line2 whole power output time T2-2: Line2 half power output time T2-3: Line2 Turn-off output time VsTH：Lamp turn-on while voltage of solar panel less than it. And turn-off while more than it Vf1：27.5V T1-1：05h T1-2：03h T1-3：03h T2-1：05h T2-2：03h T2-3：03h VsTH：06.0V It‟s saved Press The „ENTER‟ or The „ESC‟ VwTH : 18V VwTH is mean rise voltage of wind turbine output. Please mind 18v was rectified value, wind-turbine output approximate 13vac, If be 12v system, will showing 8.0v. wind turbine output approximate 6vac, controller will rise up.
- 8. Page - 8 - of 9 When you have completed all setting, please to disconnection battery aim to power off controller, then 10seconds later, to re-start connection of battery to power on controller. This is intent to make sure the program running in modified setting condition. 10. Performance Parameters 10.1 Wind generator control set-up definition: Rated Wind Turbine Power 200W – 600W Wind Turbine Maximum Input Power 800W Wind Turbine Input Current Max. 30A 12V System Unload Voltage (Vf1) Factory default: 13.5V adjustable 24V System Unload Voltage (Vf1) Factory default: 27.0V adjustable 10.2 PV panel set-up definition Max PV power (12v/24v) 150W / 300W 12V system max open circuit voltage 18.0V 24V system max open circuit voltage 36.0V Solar panel max charge current 15.0A 10.3 Battery management definition 12V system voltage protection Over-discharge Voltage factory default : 10.5V adjustable Over-discharge Recovery Voltage factory default : 12.5V adjustable Over-charge Voltage factory default : 14.4V adjustable Over-charge Recovery Voltage factory default : 13.0V adjustable 24V system voltage protection Over-discharge Voltage factory default : 21.0V adjustable Over-discharge Recovery Voltage factory default : 25.0V adjustable Over-charge Voltage factory default : 28.8V adjustable Over-charge Recovery Voltage factory default : 26.0V adjustable Output Set-up function: Each Line Output Max. Current 10A Each Line Output Max. Power (12V/24V) 120W / 150W Output Mode Constant output setting Light sensor value ( VSTH) factory default : 6.0V adjustable 10.4 Product Conventional parameter Display super large LED (Backlit)
- 9. Page - 9 - of 9 Display Content Battery Voltage, Charge Current, Wind Turbine Voltage/Current, PV Voltage/Current, over-charge voltage, over-discharge voltag e, battery value% ,day or Night and system status Standard communication interface RS232（adjustable RS485，RJ45，GPRS etc.） Operating temperature -20℃ ~ +50℃ / 35~85%RH（free from condensation.） Altitude work ≤3000 meters above sea level Protection class IP55 Dimension (LWH) 175mm X 145mm X 75mm Net-weight 1.3 Kg 11. Warranty and after Sales Service We provide 1 year warranty for our product from the date of delivery If the product is exceed warranty or damaged by transportation, improper operation , human element, force majeure, it is not under warranty. 12. Declare: The product has applied for patent protection, counterfeiting will be subject to legal sanctions. Our Company reserves the right to change products and without notice when products update.