Valve type-modi-11
Download as DOC, PDF3 likes2,794 views
This document discusses control valves and their components. It provides details on common valve types including globe valves, ball valves, butterfly valves, and plug valves. It describes the basic components of each valve type as well as their typical applications, advantages, and disadvantages. It also discusses factors to consider when selecting and sizing a control valve for a given application.
Valve type-modi-11
- 1. A basic control system would normally consist of the following components: Control valves,Actuators,Controllers,Sensors. All of these terms are generic and each can include many variations and characteristics. With the advance of technology, the dividing line between individual items of equipment and their definitions are becoming less clear. For example, the positioner, which traditionally adjusted the valve to a particular position within its range of travel, can now: • Take input directly from a sensor and provide a control function. • Interface with a computer to alter the control functions, and perform diagnostic routines. • Modify the valve movements to alter the characteristics of the control valve. • Interface with plant digital communication systems. Control Valves Whilst a wide variety of valve types exist, this document will concentrate on those which are most widely used in the automatic control of steam and other industrial fluids. These include valve types which have linear and rotary spindle movement. Linear types include globe valves and slide valves. Rotary types include ball valves, butterfly valves, plug valves and their variants. Globevalves: Globe valves are frequently used for control applications because of their suitability for throttling flow and the ease with which they can be given a specific 'characteristic', relating valve opening to flow. Figure 1 is a diagrammatic representation of a single seat two-port globe valve. In this case the fluid flow is pushing against the valve plug and tending to keep the plug off the valve seat. Best Suited Control: Linear and Equal percentage Recommended Uses: 1. Throttling service/flow regulation 2. Frequent operation Applications: Liquids, vapors, gases, corrosive substances, slurries Advantages: 1. Efficient throttling 2. Accurate flow control 3. Available in multiple ports
- 2. Disadvantages: 1.High pressure drop 2. More expensive than other valves Fig. 1 Flow through a single seat, two-port globe valve The difference in pressure upstream (P1) and downstream (P2) of the valve, against which the valve must close is known as the differential pressure (DP). The maximum differential pressure against which a valve can close will depend upon the size and type of valve and the actuator operating it. In broad terms, the force required from the actuator may be determined using Equation.1. eq 1 Where: A= Valve seating area (m2 ) ∆P = Differential pressure (kPa) F = Closing force required (kN) In a steam system, the maximum differential pressure is usually assumed to be the same as the upstream absolute pressure. This allows for possible vacuum conditions downstream of the valve when the valve closes. The differential pressure in a closed water system is the maximum pump differential head. If a larger valve, having a larger orifice, is used to pass greater volumes of the medium, then the force that the actuator must develop in order to close the valve will also increase. Where very large capacities must be passed using large valves, or where
- 3. very high differential pressures exist, the point will be reached where it becomes impractical to provide sufficient force to close a conventional single seat valve. In such circumstances, the traditional solution to this problem is the double seat two-port valve. As the name implies, the double seat valve has two valve plugs on a common spindle, with two valve seats. Not only can the valve seats be kept smaller (since there are two of them) but also, the forces are partially balanced. This means that although the differential pressure is trying to keep the top valve plug off its seat (as with a single seat valve) it is also trying to push down and close the lower valve plug. Rotary Type Valves Rotary type valves, often called quarter-turn valves, include plug valves, ball valves and butterfly valves. All require a rotary motion to open and close, and can easily be fitted with actuators. Eccentric plug valves Figure 2 shows a typical eccentric plug valve. These valves are normally installed with the plug spindle horizontal as shown, and the attached actuator situated alongside the valve. Plug valves may include linkages between the plug and actuator to improve the leverage and closing force, and special positioners that modify the inherent valve characteristic to a more useful equal percentage characteristic . Fig. 2 Side view of an eccentric plug valve (shown in a partially open position) Ball valves Figure 3 shows a ball valve consisting of a spherical ball located between two sealing rings in a simple body form. The ball has a hole allowing fluid to pass through. When aligned with the pipe ends, this gives either full bore or nearly full bore flow with very little pressure drop. Rotating the ball through 90° opens and closes the flow passage. Ball valves designed specifically for control purposes will have characterized balls or seats, to give a predictable flow pattern.
- 4. Fig. 3 Ball valve (shown in a fully open position) Ball valves are an economic means of providing control with tight shut-off for many fluids including steam at temperatures up to 250°C (38 bar g, saturated steam). Above this temperature, special seat materials or metal-to-metal seatings are necessary, which can be expensive. Ball valves are easily actuated and often used for remote isolation and control. For critical control applications, segmented balls and balls with specially shaped holes are available to provide different flow characteristics. Best Suited Control: Quick opening, linear Recommended Uses: 1. Fully open/closed, limited-throttling 2. Higher temperature fluids Applications: Most liquids, high temperatures, slurries Advantages: Disadvantages: 1. Low cost 1. Poor throttling characteristics 2. High capacity 2. Prone to cavitation 3. Low leakage and maint. 4. Tight sealing with low torque Butterfly valves Figure 4 is a simple schematic diagram of a butterfly valve, which consists of a disc rotating in trunnion bearings. In the open position the disc is parallel to the pipe wall,
- 5. allowing full flow through the valve. In the closed position it is rotated against a seat, and perpendicular to the pipe wall. Best Suited Control: Linear, Equal percentage Recommended Uses: 1. Fully open/closed or throttling services 2. Frequent operation 3. Minimal fluid trapping in line Applications: Liquids, gases, slurries, liquids with suspended solids Advantages: Disadvantages: 1. Low cost and maint. 1. High torque required for control 2. High capacity 2. Prone to cavitation at lower flows 3. Good flow control 4. Low pressure drop Fig 4 Butterfly valve (shown in its open position)
- 6. Traditionally, butterfly valves were limited to low pressures and temperatures, due to the inherent limitations of the soft seats used. Currently, valves with higher temperature seats or high quality and specially machined metal-to-metal seats are available to overcome these drawbacks. Standard butterfly valves are now used in simple control applications, particularly in larger sizes and where limited turndown is required. Special butterfly valves are available for more demanding duties. A fluid flowing through a butterfly valve creates a low pressure drop, in that the valve presents little resistance to flow when open. In general however, their differential pressure limits are lower than those for globe valves. Ball valves are similar except that, due to their different sealing arrangements, they can operate against higher differential pressures than equivalent butterfly valves. Valve Sizing Sizing flow valves is a science with many rules of thumb. In this article I'll try to define a more standard procedure for sizing a valve as well as helping to select the appropriate type of valve. **Please note that the correlation within this article are for turbulent flow STEP #1: Define the system The system is pumping water from one tank to another through a piping system with a total pressure drop of 150 psi. The fluid is water at 70 0 F. Design (maximum) flowrate of 150 gpm, operating flowrate of 110 gpm, and a minimum flowrate of 25 gpm. The pipe diameter is 3 inches. At 70 0 F, water has a specific gravity of 1.0. Key Variables: Total pressure drop, design flow, operating flow, minimum flow, pipe diameter, specific gravity STEP #2: Define a maximum allowable pressure drop for the valve When defining the allowable pressure drop across the valve, you should first investigate the pump. What is its maximum available head? Remember that the system pressure drop is limited by the pump. Essentially the Net Positive Suction Head Available (NPSHA) minus the Net Positive Suction Head Required (NPSHR) is the maximum available pressure drop for the valve to use and this must not be exceeded or another pump will be needed. It's important to remember the trade off, larger pressure drops increase the pumping cost (operating) and smaller pressure drops increase the valve cost because a larger valve is required (capital cost). The usual rule of thumb is that a valve should be designed to use 10-15% of the total pressure drop or 10 psi, whichever is greater. For our system, 10% of the total pressure drop is 15 psi which is what we'll use as our allowable pressure drop when the valve is wide open (the pump is our system is easily capable of the additional pressure drop). STEP #3: Calculate the valve characteristic
- 7. STEP #4: Preliminary valve selection The Cv value should be used as a guide in the valve selection, not a hard and fast rule. Some other considerations are: a. Never use a valve that is less than half the pipe size b. Avoid using the lower 10% and upper 20% of the valve stroke. The valve is much easier to control in the 10-80% stroke range. STEP #5: Check the Cv and stroke percentage at the minimum flow If the stroke percentage falls below 10% at our minimum flow, a smaller valve may have to be used in some cases. Judgements plays role in many cases. For example, is your system more likely to operate closer to the maximum flowrates more often than the minimum flowrates? Or is it more likely to operate near the minimum flowrate estimate is conservative. STEP #6: Check the gain across applicable flowrates Gain is defined as: OTHER NOTES: Another valve characteristic that can be examined is called the choked flow. t Usually, the rule of thumb for determining the maximum pressure drop across the valve also helps to avoid choking flow Selecting a pneumatic valve and actuator In summary, the following is a list of the major factors that must be considered when selecting a pneumatic valve and actuator: 1. Select a valve using the application data. 2. Determine the valve action required in the event of power failure, fail-open or fail-closed. 3. Select the valve actuator and spring combination required to ensure that the valve will open or close against the differential pressure. 4. Determine if a positioner is required. 5. Determine if a pneumatic or electric control signal is to be provided. This will determine whether an I to P converter or, alternatively a combined I to P converter/positioner, is required.
- 8. Control valves handle all kinds of fluids at temperatures from the cryogenic range to well over 1000_F(538_C). Selection of a control valve body assembly requires particular consideration to provide the best available combination of valve body style, material, and trim construction design for the intended service. Capacity requirements and system operating pressure ranges also must be considered in selecting a control valve to ensure satisfactory operation without undue initial expense. Reputable control valve manufacturers and their representatives are dedicated to helping select the control valve most appropriate for the existing service conditions. Because there are frequently several possible correct choices for an application, it is important that all the following information be provided: _ Type of fluid to be controlled _ Temperature of fluid _ Viscosity of fluid _ Specific gravity of fluid _ Flow capacity required (maximumand minimum) _ Inlet pressure at valve (maximumand minimum) _ Outlet pressure (maximum andminimum) _ Pressure drop during normal flowing conditions _ Pressure drop at shutoff _ Maximum permissible noise level, if pertinent, and the measurement reference point _ Degrees of superheat or existence of flashing, if known _ Inlet and outlet pipeline size andschedule _ Special tagging information required _ Body Material (ASTM A216grade WCC, ASTM A217 grade WC9,ASTM A351 CF8M, etc.) _ End connections and valve rating (screwed, Class 600 RF flanged,Class 1500 RTJ flanges, etc.) _ Action desired on air failure(valve to open, close, or retain last controlled position) _ Instrument air supply available _ Instrument signal (3 to 15 psig, 4to 20 mA, Hart, etc.) In addition the following information will require the agreement of the user and the manufacturer depending on the purchasing and engineering practices being followed. _ Valve type number _ Valve size _ Valve body construction (angle,double-port, butterfly, etc.) _ Valve plug guiding (cage-style, port-guided, etc.) _ Valve plug action (push-down-to-close or push-down-toopen) _ Port size (full or restricted) _ Valve trim materials required _ Flow action (flow tends to open valve or flow tends to close valve) _ Actuator size required _ Bonnet style (plain, extension, bellows seal, etc.) _ Packing material (PTFE V-ring, laminated graphite, environmental sealing systems, etc.) _ Accessories required (positioner, handwheel, etc.)
- 9. VALVE SELECTION PROCESS 1. DETERMINE SERVICE CONDITIONS _ (P1, ΔP, Q, T1, Fluid Properties, Allowable Noise, etc). _ Select appropriate ANSI Pressure Class required for valve body and trim. 2. CALCULATE PRELIMINARY Cv REQUIRED _ Check noise and cavitation levels 3. SELECT TRIM TYPE _ If no noise or cavitation indication, choose standard trim. _ If aerodynamic noise is high, choose Whisper Trim_. _ If liquid noise is high and/or cavitation is indicated, choose Cavitrol_ III trim. 4. SELECT VALVE BODY AND TRIM SIZE _ Select valve body and trim size with required Cv. _ Note travel, trim group, and shutoff options. 5. SELECT TRIM MATERIALS Select trim materials for your application; make sure trim selected is available in the trim group for the valve size selected. 6.OPTIONS Consider options on shutoff, stem packing,etc. Flow characteristics All control valves have an inherent flow characteristic that defines the relationship between 'valve opening' and flowrate under constant pressure conditions. Note that 'valve opening' in this context refers to the relative position of the valve plug to its closed position against the valve seat. It does not refer to the orifice pass area. The orifice pass area is sometimes called the 'valve throat' and is the narrowest point between the valve plug and seat through which the fluid passes at any time. For any valve, however it is characterised, the relationship between flowrate and orifice pass area is always directly proportional. Valves of any size or inherent flow characteristic which are subjected to the same volumetric flowrate and differential pressure will have exactly the same orifice pass area. However, different valve characteristics will give different 'valve openings' for the same pass area. Comparing linear and equal percentage valves, a linear valve might have a 25% valve opening for a certain pressure drop and flowrate, whilst an equal percentage valve might have a 65% valve opening for exactly the same conditions. The orifice pass areas will be the same. The physical shape of the plug and seat arrangement, sometimes referred to as the valve 'trim', causes the difference in valve opening between these valves. Typical trim shapes for spindle operated globe valves are compared in Figure 5.
- 10. Fig.5 The shape of the trim determines the valve characteristic The term 'valve lift' is used to define valve opening, whether the valve is a globe valve (up and down movement of the plug relative to the seat) or a rotary valve (lateral movement of the plug relative to the seat). Rotary valves (for example, ball and butterfly) each have a basic characteristic curve, but altering the details of the ball or butterfly plug may modify this. The inherent flow characteristics of typical globe valves and Rotary valves are copared infig6. Globe valves may be fitted with plugs of differing shapes, each of which has its own inherent flow/opening characteristic. The three main types available are usually designated: • Fast opening / Quick opening. • Linear. • Equal percentage. Examples of these and their inherent characteristics are shown in Figures 5 and 6
- 11. Fig. 6 Inherent flow characteristics of typical globe valves and rotary valves Fast opening characteristic: The fast opening characteristic valve plug will give a large change in flowrate for a small valve lift from the closed position. For example, a valve lift of 50% may result in an orifice pass area and flowrate up to 90% of its maximum potential. A valve using this type of plug is sometimes referred to as having an 'on / off' characteristic. Fast opening valves tend to be electrically or pneumatically actuated and used for 'on / off' control. Used for processes where "instantly" large flow is needed (ie. safety systems or cooling water systems) Linear characteristic: The linear characteristic valve plug is shaped so that the flowrate is directly proportional to the valve lift (H), at a constant differential pressure. A linear valve achieves this by having a linear relationship between the valve lift and the orifice pass area (see Figure 7). Fig. 7 Flow / lift curve for a linear valve
- 12. For example, at 40% valve lift, a 40% orifice size allows 40% of the full flow to pass. Used in liquid level or flow loops Used in systems where the pressure drop across the valve is expected to remain fairly constant (ie. steady state systems) Equal percentage characteristic (or logarithmic characteristic) These valves have a valve plug shaped so that each increment in valve lift increases the flowrate by a certain percentage of the previous flow. The relationship between valve lift and orifice size (and therefore flowrate) is not linear but logarithmic, and is expressed mathematically in Equation 2: Equation 2 Where: = Volumetric flow through the valve at lift H. x= (ln ) H Note: 'In' is a mathematical function known as 'natural logarithm'. = Valve rangeability (ratio of the maximum to minimum controllable flowrate, typically 50 for a globe type control valve) H= Valve lift (0 = closed, 1 = fully open) max = Maximum volumetric flow through the valve Used in processes where large changes in pressure drop are expected. Used in processes where a small percentage of the total pressure drop is permitted by the valve . Used in temperature and pressure control loops Example The maximum flowrate through a control valve with an equal percentage characteristic is 10 m3 /h. If the valve has a turndown of 50:1, and is subjected to a constant differential pressure, by using Equation 6.5.1 what quantity will pass through the valve with lifts of 40%, 50%, and 60% respectively? Where: max = Maximum volumetric flow through the valve = 10 m3 /h H= Valve lift (0 closed to 1 fully open) = 0.4; 0.5; 0.6 = Valve rangeability = 50 Equation 2
- 13. The increase in volumetric flowrate through this type of control valve increases by an equal percentage per equal increment of valve movement: • When the valve is 50% open, it will pass 1.414 m3 /h , an increase of 48% over the flow of 0.956 m3 /h when the valve is 40% open. • When the valve is 60% open, it will pass 2.091 m3 /h , an increase of 48% over the flow of 1.414 m3 /h when the valve is 50% open. It can be seen that (with a constant differential pressure) for any 10% increase in valve lift, there is a 48% increase in flowrate through the control valve. This will always be the case for an equal percentage valve with rangeability of 50. For interest, if a valve has a rangeability of 100, the incremental increase in flowrate for a 10% change in valve lift is 58%. Table shows how the change in flowrate alters across the range of valve lift for the equal percentage valve in Example with a rangeability of 50 and with a constant differential pressure.
- 14. Table Change in flowrate and valve lift for an equal percentage characteristic with constant differential pressure Fig. 7 Flowrate and valve lift for an equal percentage characteristic with constant differential pressure for Example A few other inherent valve characteristics are sometimes used, such as parabolic, modified linear or hyperbolic, but the most common types in manufacture are fast opening, linear, and equal percentage. There are always a number of options to consider when choosing a control valve. For globe valves, these include a choice of spindle gland packing material and gland packing configurations, which are designed to make the valve suitable for use on higher temperatures or for different fluids. It is worth noting that certain types of gland packing produce a greater friction with the valve spindle than others. For example, the traditional stuffing box type of packing will create greater friction than the PTFE spring-loaded chevron type or bellows sealed type. Greater friction requires a higher actuator force and will have an increased propensity for haphazard movement. Spring-loaded packing re-adjusts itself as it wears. This reduces the need for regular manual maintenance. Bellows sealed valves are the most expensive of these three types, but provide minimal friction with the best stem sealing mechanism. Bellows sealed valves usually have another set of traditional packing at the top of the valve
- 15. spindle housing. This will act as a final defence against any chance of leaking through the spindle to atmosphere. Valve Performance Introduction to Valve Capacity A control valve must, as its name suggests, have a controlling influence on the process. Whilst details such as connection sizes and materials of construction are vitally important, they do not give any indication of the Control exerted by the valve. Control valves adjust processes by altering: • Flowrate - For example, the amount of steam or water that enters the process equipment. • With a two-port valve for example, as the valve moves to the closed position, less steam flows, and less heat is added to the process. With a three-port valve for example, as the valve plug moves to a new position, it diverts hot water away from the process. And/or • Differential pressure - This is defined as the difference between the pressure at the valve inlet and the pressure at the valve outlet For any given valve orifice size, the greater the differential pressure the greater the flowrate, within certain limitations. With saturated steam, the lower its pressure, the lower its temperature, and less heat transfer will occur in the heat exchanger. These two factors (a) Flowrate and (b) Differential pressure are brought together as a flow coefficient or 'capacity index' as it is sometimes termed. The flow coefficient allows: • The performance of valves to be compared. • The differential pressure across a valve to be determined from any flowrate. • The flowrate through a control valve to be determined for a given differential pressure.
- 16. Symbols and definitions used to identify and quantify flow through a control valve For conversion: C v (Imperial) = K v x 0.962 658 C v (US) = K v x 1.156 099 A v = 2.88�x�10-5 C v (Imperial) The flow coefficient, Kvs for a control valve is essential information, and is usually stated, along with its other data, on the manufacturer's technical data sheets. Control valve manufacturers will usually offer a number of trim sizes (combination of valve seat and valve plug) for a particular valve size. This may be to simplify the pipe work by eliminating the need for reducers, or to reduce noise. The relationship between flowrates, differential pressures, and the flow coefficients will vary depending upon the type of fluid flowing through the valve.