1. WELL LOG (The Bore Hole Image)
What is well Logging
Well log is a continuous record of measurement made in bore hole respond to
variation in some physical properties of rocks through which the bore hole is drilled.
Traditionally Logs are display on girded papers shown in figure.
Now a days the log may be taken as films, images, and in digital format.
2. HISTORY
1912 Conrad Schlumberger give the idea of using electrical measurements to map subsurface
rock bodies.
in 1919 Conrad Schlumberger and his brother Marcel begin work on well logs.
The first electrical resistivity well log was taken in France, in 1927.
The instrument which was use for this purpose is called SONDE, the sond was stopped at
periodic intervals in bore hole and the and resistivity was plotted on graph paper.
In 1929 the electrical resistivity logs are introduce on commercial scale in Venezuela, USA and
Russia
For correlation and identification of Hydrocarbon bearing strata.
The photographic – film recorder was developed in 1936 the curves were SN,LN AND LAT
The dip meter log were developed in 1930
The Gamma Ray and Neutron Log were begin in 1941
3. LOGGING UNITS
• Logging service companies utilize a variety of
logging units, depending on the location
(onshore or offshore) and requirements of the
logging run. Each unit will contain the
following components:
• logging cable
• winch to raise and lower the cable in the well
• self-contained 120-volt AC generator
• set of surface control panels
• set of downhole tools (sondes and cartridges)
• digital recording system
8. LOG INTERPRETATION OBJECTIVES
• The objective of log interpretation depends very much on the user. Quantitative analysis of well logs provides
the analyst with values for a variety of primary parameters, such as:
• porosity
• water saturation, fluid type (oil/gas/water)
• lithology
• permeability
• From these, many corollary parameters can be derived by integration (and other means) to arrive at values for:
• hydrocarbons-in-place
• reserves (the recoverable fraction of hydrocarbons in-place)
• mapping reservoir parameters
• But not all users of wireline logs have quantitative analysis as their objective. Many of them are more concerned
with the geological and geophysical aspects. These users are interested in interpretation for:
• well-to-well correlation
• facies analysis
• regional structural and sedimentary history
• In quantitative log analysis, the objective is to define
• the type of reservoir (lithology)
• its storage capacity (porosity)
• its hydrocarbon type and content (saturation)
• its producibility (permeability)
9. GAMMA RAY LOG
GAMMA RAY LOG
• Gamma Rays are high-energy electromagnetic waves which are emitted by atomic nuclei as a form
of radiation
• Gamma ray log is measurement of natural radioactivity in formation verses depth.
• It measures the radiation emitting from naturally occurring U, Th, and K.
• It is also known as shale log.
• GR log reflects shale or clay content.
• Clean formations have low radioactivity level.
• Correlation between wells,
• Determination of bed boundaries,
• Evaluation of shale content within a formation,
• Mineral analysis,
• Depth control for log tie-ins, side-wall coring, or perforating.
• Particularly useful for defining shale beds when the sp is featureless
• GR log can be run in both open and cased hole
10. Spontaneous Potential Log (SP)
Spontaneous Potential Log (SP)
• The spontaneous potential (SP) curve records
the naturally occurring electrical potential
(voltage) produced by the interaction of
formation connate water, conductive drilling
fluid, and shale
• The SP curve reflects a difference in the
electrical potential between a movable
electrode in the borehole and a fixed reference
electrode at the surface
• Though the SP is used primarily as a lithology
indicator and as a correlation tool, it has other
uses as well:
– permeability indicator,
– shale volume indicator
– porosity indicator, and
– measurement of Rw (hence formation
water salinity).
11. Neutron Logging
Neutron Logging
• The Neutron Log is primarily used to evaluate
formation porosity, but the fact that it is really
just a hydrogen detector should always be kept in
mind
• It is used to detect gas in certain situations,
exploiting the lower hydrogen density, or
hydrogen index
• The Neutron Log can be summarized as the
continuous measurement of the induced radiation
produced by the bombardment of that formation
with a neutron source contained in the logging
tool which sources emit fast neutrons that are
eventually slowed by collisions with hydrogen
atoms until they are captured (think of a billiard
ball metaphor where the similar size of the
particles is a factor). The capture results in the
emission of a secondary gamma ray; some tools,
especially older ones, detect the capture gamma
ray (neutron-gamma log). Other tools detect
intermediate (epithermal) neutrons or slow
(thermal) neutrons (both referred to as neutron-
neutron logs). Modern neutron tools most
commonly count thermal neutrons with an He-3
type detector.
12. The Density Log
The Density Log
• The formation density log is a porosity log that measures electron
density of a formation
• Dense formations absorb many gamma rays, while low-density formations
absorb fewer. Thus, high-count rates at the detectors indicate low-density
formations, whereas low count rates at the detectors indicate high-density
formations.
• Therefore, scattered gamma rays reaching the detector is an indication of
formation Density.
Scale and units:
The most frequently used scales are a range of 2.0 to 3.0 gm/cc or 1.95
to 2.95 gm/cc across two tracks.
A density derived porosity curve is sometimes present in tracks #2 and
#3 along with the bulk density (rb) and correction (Dr) curves. Track #1
contains a gamma ray log and caliper.
13. Resistivity Log
Resistivity Log
• Basics about the Resistivity:
• Resistivity measures the electric properties of the formation,
• Resistivity is measured as, R in W per m,
• Resistivity is the inverse of conductivity,
• The ability to conduct electric current depends upon:
• The Volume of water,
• The Temperature of the formation,
• The Salinity of the formation
The Resistivity Log:
Resistivity logs measure the ability of rocks to
conduct electrical current and are scaled in units of ohm-
meters.
The Usage:
Resistivity logs are electric logs which are used
to:
Determine Hydrocarbon versus Water-bearing zones,
Indicate Permeable zones,
Determine Resisitivity Porosity.
14. Shahbaz Younis (Pakistan)
• Acoustic tools measure the speed of sound waves in
subsurface formations. While the acoustic log can be
used to determine porosity in consolidated formations, it
is also valuable in other applications, such as:
• Indicating lithology (using the ratio of compressional
velocity over shear velocity),
• Determining integrated travel time (an important tool for
seismic/wellbore correlation),
• Correlation with other wells
• Detecting fractures and evaluating secondary porosity,
• Evaluating cement bonds between casing, and formation,
• Detecting over-pressure,
• Determining mechanical properties (in combination with
the density log), and
• Determining acoustic impedance (in combination with the
density log).
Acoustic Log
Acoustic Log
15. This powerpoint was kindly donated to
www.worldofteaching.com
http://www.worldofteaching.com is home to over a
thousand powerpoints submitted by teachers. This is a
completely free site and requires no registration. Please
visit and I hope it will help in your teaching.
