Zipato zipabox user_guide

Zipabox
QUICK INSTALLATION GUIDE
v.1

1|P a g e

Copyright
© 2012 Tri plus grupa d.o.o. All Rights Reserved.
Copyright by Tri plus grupa d.o.o.. No part of this manual may be
reproduced or transmitted in any form without the expressed, written
permission of Tri plus grupa d.o.o.

Trademarks
Zipato and the Zipato logo are registered Trademarks All other product
names mentioned herein may be trademarks or
registered trademarks of their respective companies.

Notice
Although Zipato has attempted to ensure the accuracy of the content
of this manual, it is possible that this document may contain technical
inaccuracies, typographical, or other errors. Zipato assumes no liability
for any error in this publication, and for damages, whether direct,
indirect, incidental, and consequential or otherwise, that may result
from such error, including, but not limited to loss of data or profits.
Zipato provides this publication “as is” without warranty of any kind,
either express or implied, including, but not limited to implied
warranties of merchantability or fitness for a particular purpose.
The published information in the manual is subject to change without
notice.
Zipato reserves the right to make changes in the product design,
layout, and driver revisions without notification to its users.
This version of the Installation guide supersedes all previous versions.

2|P a g e

Important Safety Information
To avoid contact with electrical current:
• Never install an Ethernet connection in wet locations unless that
connector is specifically designed for wet locations.
• Do not place Ethernet wiring or connections in any conduit, outlet
or junction box containing electrical wiring.
• Installation of inside wire may bring you close to electrical wire,
conduit, terminals and other electrical facilities. Extreme caution
must be used to avoid electrical shock from such facilities. Avoid
contact with all such facilities.
• Ethernet wiring must be at least 2 m from bare power wiring or
lightning rods and associated wires, and at least 15 cm from
other wire (antenna wires, doorbell wires, wires from
transformers to neon signs), steam or hot water pipes, and
heating ducts.

Electromagnetic compatibility
In proper state and when operated properly, the product complies with
all the requirements in respect of interference radiation according to
EN 301 489-17, EN 301 489-1 and EN 300 328. The connections
conducting HF signals must neither be manipulated nor damaged.

3|P a g e

Table of Contents

INTRODUCTION .................................................................. 5
CONTENTS OF PACKAGING ............................................ 13
CONNECT THE ZIPABOX.................................................. 14
CREATE A USER ACCOUNT AND REGISTER YOUR
SYSTEM............................................................................. 16
INSTALLATION/MOUNTING ZIPABOX .............................. 18
ADDING DEVICES ............................................................. 19
TROUBLESHOTING........................................................... 20
SPECIFICATIONS .............................................................. 23
LIMITED PRODUCT WARRANTY ...................................... 24
DECLARATION OF CONFORMITY .................................... 29
DISPOSING AND RECYCLING YOUR PRODUCT ............ 31

4|P a g e

INTRODUCTION
Thank you for purchasing Zipabox smart home automation
controller. This guide describes how to install, program and
operate your Zipabox.

Zipabox makes every home smart
Zipabox Controller uses advanced technology to hide the
complexity of home networking - delivering a simple smart
home. It plugs into any outlet in the home and automatically
talks to all the connected devices in the house, connecting
them to the cloud so that consumers can control them using
tablets, smart phones, computers or TVs— at home or on the
go.

The Zipabox Gateway supports variety of communication
standards including Z-WAVE, ZIGBEE, KNX, ONVIF, and
UPnP.

The Zipabox’s capabilities can easily be expanded using
“snap-in” expansion modules that will add support for new
interfaces and functionalities, communication standards and
protocols, etc.

5|P a g e

Once configured, the gateway works stand-alone, but also
features cloud support for advanced monitoring, messaging
and programing services.

Intuitive graphical user interface allows customers to program
their own home rules without any previous programing
experience.

Security and safety
• unlimited number of virtual alarms (partitions)
• up to 233 two-way, wireless zones
• trigger alarms in case of:
o intruder (motion sensors and door/window
sensors),
o fire (smoke sensors),
o flood (water leakage sensors),
o gas (CO sensors)
o panic button,
o duress (if someone force you to disarm your
system)
o health care (in case of missing actions during
particular time e.g. motion, door opening,
laying on bed...)

6|P a g e

• remote arm/disarm and status-info with any smartphone
• vandal proof - Zipabox is 24/7 monitored by central
station which triggers alarm in case of connection loss
• include arm/disarm commands in automation scenes
and rules
• integration with existing alarm systems (DSC,
Honeywell...)
• easy online setup and configuration through web based
interface
• use of same sensors for security and automation
purposes

Lighting
• easy installation of wireless modules
• Z-Wave and ZigBee lighting modules pre-configured for
even easier setup
• support remote dimming and on/off switching with any
smartphone
• automatically turn lights on at sunset and off at sunrise
• unlimited number of scenes supported
• turn lights on during emergencies
• advanced event based rules configuration

7|P a g e

• auto-pilot lighting programs to discourage intruders while
home is empty

Climate
• multi-room heating and cooling control with any
smartphone
• advanced programing scheduler online, accessible over
web browser
• easily create unlimited number of custom zones
(thermostats)
• multi-zone humidity control by using standard humidifiers
and dehumidifiers
• use Internet weather feeds to program your home
climate conditions
• create advanced event based rules to automate home
climate based on other environmental and home events
• include climate control in automation scenes together
with alarm, lighting, shades, etc
• Notification and automated actions in case of over-
temperature events, power outages, and other
incidents…

8|P a g e

Sun shading
• control blinds, roller-shutters, curtains and pergolas
using any smartphone
• automate motors by using fun and easy programing tool
online
• add your sun shading commands into home scenarios
together with lights, climate, alarms...
• automate your shades to react to outside weather
conditions
• easy installation using pre-configured wireless modules

Irrigation
• control unlimited number of irrigation zones
• use advanced programing options online to setup perfect
irrigation process
• automate irrigation system based on Internet weather
forecast
• integrate your irrigation scheme together with your
complete home automation scenarios

9|P a g e

Access
• remotely lock/unlock your door with any smartphone
• remotely open/close your garage door or gate over any
smartphone
• get video notification when door is open
• use RFID tags to open doors and get detailed statistics
about exits/entries
• automate doors/locks using scenarios and event based
programing tool
• trigger automation events when door lock user codes are
entered
• automatically unlock doors in the event of an emergency

Multimedia
• remotely control your audio/video equipment with any
smartphone
• automatically turn on favorite shows when they air and
get alerts
• automatically turn off A/V equipment at pre-set time or
when room is unoccupied
• automatically turn on equipment to discourage intruders

10 | P a g e

Video monitoring
• access live and recorded video via the web and from
any smartphone
• support for most of the available IP cameras – ONVIF
support
• get email and SMS notifications with pictures and live
video attached
• remotely adjust pan-tilt cameras
• create advanced event based recording and video
notification rules

Energy Metering
• real-time monitoring energy consumption and notification
right on smartphone
• compare energy usage and cost with others in the area
• automatically turn on/off your appliances in accordance
with electricity prices
• see detailed analysis of your energy consumption
• save energy by automating lights, thermostats, sun
shades...

11 | P a g e

Take care of your safety
Display extreme caution when using ladders or steps, please
follow manufacturer’s instructions. Be careful when using
hand and power tools and follow the manufacturer’s
guidelines when using them. Take care that the correct tools
are used. Wear goggles or protective clothing where required.

Technical support
Having trouble installing your new product? Zipato’s website
contains the latest user documentation and software updates
for Zipato products and services.

www.zipato.com

Call support: + 385 1 444 444 00
(Mon-Fri) 9.00am-06.00pm

12 | P a g e

CONTENTS OF PACKAGING

1x Zipabox
1x Power adapter 230V AC to 12V DC
1x 868 MHz antenna for Z-wave network
1x Ethernet cable
1x User manual

13 | P a g e

CONNECT THE ZIPABOX

1. Locate your serial number
Screw Z-wave antenna to
Antenna1 connector.

2. Connecting to broadband
Connect your Zipabox to your
broadband router via the
Ethernet cable. The Ethernet
port is located on the back of
the Zipabox.

Network Antena 2
Power Reset Antena 1

14 | P a g e

3. Power up

Plug the power adaptor into the mains
Supply wall socket and the other end
into the control unit.

You should see the following LED sequence:
After approximately 2
minutes LED 3 will flash
- Yellow light GREEN, indicating that the
unit is network operational
- Yellow flashing but not yet registered for
service. If you do not see
- Green light flashing this sequence of LED’s,
please see guidance in
- Green light - Troubleshooting and
- CONNECTED Support (at the end of this
guide)

15 | P a g e

CREATE A USER ACCOUNT AND REGISTER YOUR
SYSTEM

Account creation
To benefit from the Zipato monitoring and control service you
will need to set up your Zipato account and register your
Zipabox. Upon registration you will automatically get the
basic free level of monitoring service.

1. Open a browser window on your PC and go to the
following URL: my.zipato.com
2. Click on ‘Register’ and follow the on-screen instructions.

Take note of your password during this process. Once your
account has been set up, go to the login page and login to
your account.

Register your Zipabox
When you first time log in to your account, you need to enter
serial number of your Zipabox in pop-up form. You can find
your serial number on the back of your Zipabox.

16 | P a g e

Finalize your account
Your account is set up and you are able to use Zipato cloud
system. Anyway, you need to ensure that your account is fully
set up so you get the most from your Zipato account.

This includes:

Account Details
Make sure that you have fully completed your profile. Go to
General settings in the General widget and select Details
tab.

Users
The Users section is where you add your family members
which will have the rights to use your system. Adding new
user requires you to enter new user’s details and to give
him/her certain rights. Rights management allows you to
permit some services for some users.

17 | P a g e

INSTALLATION/MOUNTING ZIPABOX
Zipato provide three methods of mounting.

Wall mounting
Drill holes in the wall surface and insert the wall plugs if fixing
into plaster or brick holes. Drill two holes, fix the screws and
hook the Zipabox onto the screw’s heads. Make sure swivel
antenna is in vertical position.

Din-rail mounting
Make enough space for Zipabox on your Din-rail. Hook upper
fitters on the back of your Zipabox to the Din rail and press
Zipabox slightly to snap lower fitters.

Table top
You can place your Zipabox on any table top. Just make sure
that swivel antenna is in vertical position.

18 | P a g e

ADDING DEVICES

Adding new devices Z-wave or ZigBee
Recommended distance between sensor and Zipabox should
be less than one meter.

1. On Zipato dashboard, click “ADD NEW DEVICE” button
in General widget and follow wizard instructions. For Z-
wave devices, it is recommended that you reset you
device before adding it to the Zipato network.

2. After you successfully add the device in to your Zipato
network go to “NEW DEVICES” in General widget and
set your device’s room name and type. This will help you
to control your device easier.

19 | P a g e

TROUBLESHOTING

Waiting for more than a five minutes and still there is no
green LED light.
1. Check your Internet connection
2. Check whether you connected your network cable
correctly to your Internet router.

I forgot my password
1. Go to my.zipato.com
2. Click “Forgot password” and follow screen
instruction.

I can’t connect any Z-wave or Zigbee device to my box
Check whether your antenna supplied with Zipabox is
correctly mounted on Antenna 1 connector.

20 | P a g e

I have placed a device outside my house and it is not
communicating with the Zipabox. What's happening?
f you have a lot of metal in the exterior construction of your
home, this could significantly impede wireless communication.
Metal is an insulator of radio signals. If your house has metal
siding or a stucco finish over a metal mesh, you may have
range problems on devices outside your home
communicating with the Zipabo inside.

What should I do if I am having trouble installing my
device?

If you are having difficulty with the physical installation of non-
Zipato branded devices (Thermostats, GE switches, Blueline
meter reader, etc.), please contact the manufacturer directly
for assistance.
If you are having trouble pairing a device to the Zipabox,
check the videos or other content on Zipato website for
assistance.

21 | P a g e

Does Zipato offer a warranty?
See the Limited Product Warranty for specifics of the Zipato
service warranty.

22 | P a g e

SPECIFICATIONS
System Accessories
ARM9 208MHz CPU CAT5e UTP patch LAN Cable
32MB RAM Antenna Z-wave
128MB Flash Antenna Zigbee (option)

Network Regulatory Compliance
Ethernet (pending)
Z-Wave (US or EU) Safety: UL
ZigBee (802.15.4) (option) EMC: FCC, CE
RoHS
Operating System
Linux 2.6 Kernel Automation option
Remote automation software
Power Online remote control interface
Power input: 9-12VDC
Power supply input: 100-240VAC, Environmental
50/60Hz Temperature Range:
Power usage: Idle: 1.2W, Max: Operating: 0° to 40° (32° to
C C F
2.4W 104°F)
Storage: -25° to 70° (-13° to
C C F
Physical Dimension 158°F)
86 (L) x 8 (W) x 4 (H) millimeters Humidity: 5% to 95% non-
34in(L)x34(W)x19(H) inches condensing

I/O & LEDs Warranty
2 programmable buttons 1 year standard
2 programmable green LEDs
1 programmable RGB LEDs
Power, Status, Ethernet, WLAN & Specifications are subject to
Z-Wave change without prior notice

23 | P a g e

LIMITED PRODUCT WARRANTY

GENERAL TERMS
Nothing in this Limited Product Warranty affects your statutory rights as a
consumer.
The Limited Product Warranty set forth below is given by Tri plus grupa d.o.o.
(Europe) (herein referred to as "ZIPATO"). This Limited Product Warranty is only
effective upon presentation of the proof of purchase. Upon further request by
ZIPATO, this warranty card has to be presented, too.
EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY, ZIPATO
MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. ZIPATO EXPRESSLY DISCLAIMS ALL WARRANTIES
NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES
THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE
LIMITED WARRANTY PERIOD.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS
WARRANTY STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE
REMEDIES AGAINST ZIPATO. THEY DO NOT, HOWEVER, AFFECT OR
RESTRICT THE RIGHTS YOU HAVE AGAINST THE BUSINESS YOU BOUGHT
A ZIPATO PRODUCT FROM. IN NO EVENT WILL ZIPATO BE LIABLE FOR
LOSS OF DATA OR FOR INDIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER
DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
HOWEVER, NOTHING IN THIS AGREEMENT LIMITS ZIPATO'S LIABILITY TO
YOU (I) IN THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT
RESULTING FROM ZIPATO'S NEGLIGENCE, OR (II) TO THE EXTENT

24 | P a g e

RESULTING FROM ANY FRAUDULENT MISREPRESENTATION ON THE PART
OF ZIPATO, OR (III) TO THE EXTENT ARISING UNDER PART 1 OF THE
CONSUMER PROTECTION ACT 1987 OF THE UNITED KINGDOM. SOME
STATES OR COUNTRIES DO NOT ALLOW: (1) A DISCLAIMER OF IMPLIED
WARRANTIES; (2) A LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION; OR (3) LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS. IN SUCH
STATES OR COUNTRIES, SOME EXCLUSIONS OR LIMITATIONS OF THIS
LIMITED WARRANTY MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT MAY VARY FROM STATE TO STATE OR FROM COUNTRY TO
COUNTRY. YOU ARE ADVISED TO CONSULT APPLICABLE STATE OR
COUNTRY LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS.
This Limited Product Warranty applies to ZIPATO branded hardware products
(collectively referred to as “ZIPATO Hardware Products”) sold by ZIPATO
(Europe), its European subsidiaries, affiliates, authorized resellers, or country
distributors (collectively referred to as “ZIPATO Resellers”) with this Limited
Product Warranty. The term “ZIPATO Hardware Product” is limited to the hardware
components and all its internal components including firmware. The term “ZIPATO
Hardware Product” DOES NOT include any software applications or programs.

GEOGRAPHICAL SCOPE OF THE LIMITED PRODUCT
WARRANTY
This Limited Product Warranty is applicable to Hardware Products sold by Zipato
Resellers in all countries listed at the beginning of this document under the
heading “Countries in which this ZIPATO Limited Product Warranty applies”. The
Limited Product Warranty will be honored in any country where ZIPATO or its

25 | P a g e

authorized service providers offer warranty service subject to the terms and
conditions set forth in this Limited Product Warranty. However, warranty service
availability and response times may vary from country to country and may also be
subject to registration requirements.

LIMITATION OF PRODUCT WARRANTY
ZIPATO warrants that the products described below under normal use are free
from material defects in materials and workmanship during the Limited Product
Warranty Period set forth below ("Limited Product Warranty Period"), if the product
is used and serviced in accordance with the user manual and other documentation
provided to the purchaser at the time of purchase (or as amended from time to
time). ZIPATO does not warrant that the products will operate uninterrupted or
error-free or that all deficiencies, errors, defects or non-conformities will be
corrected.
This warranty shall not apply to problems resulting from: (a) unauthorized
alterations or attachments; (b) negligence, abuse or misuse, including failure to
operate the product in accordance with specifications or interface requirements;
(c) improper handling; (d) failure of goods or services not obtained from ZIPATO or
not subject to a then-effective ZIPATO warranty or maintenance agreement; (e)
improper use or storage; or (f) fire, water, acts of God or other catastrophic events.
This warranty shall also not apply to any particular product if any ZIPATO serial
number has been removed or defaced in any way.
ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A RESULT
OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR THE ZIPATO
HARDWARE PRODUCT.

26 | P a g e

LIMITED PRODUCT WARRANTY PERIOD
The Limited Product Warranty Period starts on the date of purchase from ZIPATO.
Your dated sales or delivery receipt, showing the date of purchase of the product,
is your proof of the purchase date. You may be required to provide proof of
purchase as a condition of receiving warranty service. You are entitled to warranty
service according to the terms and conditions of this document if a repair to your
ZIPATO branded hardware is required within the Limited Product Warranty Period.
[Other than in respect of products for domestic use (in particular those listed in the
first and last boxes in the table below), this Limited Product Warranty extends only
to the original end user purchaser of this ZIPATO Hardware Product and is not
transferable to anyone who obtains ownership of the ZIPATO Hardware Product
from the original end-user purchaser.]

Product Warranty Period Table
Product Type Product Warranty Period
Zipabox controller One (1) year

IMPORTANT:
The content of "Product Type" listed above is subject to change; please refer to
the www.zipato.com for latest update.

PERFORMANCE OF THE LIMITED PRODUCT WARRANTY
If a product defect occurs, ZIPATO’s sole obligation shall be to repair or replace
any defective Zipato Hardware Product free of charge provided it is returned to an
Authorized ZIPATO Service Centre during the Limited Warranty Period. Such
repair or replacement will be rendered by ZIPATO at an Authorized ZIPATO

27 | P a g e

Service Centre. All component parts or hardware products that are replaced under
this Limited Product Warranty become the property of ZIPATO. The replacement
part or product takes on the remaining Limited Warranty Period of the replaced
part or product. The replacement product need not be new or of an identical make,
model or part; ZIPATO may in its discretion replace the defective product (or any
part thereof) with any reconditioned equivalent (or superior) product in all material
respects to the defective product.

WARRANTOR
Tri plus grupa d.o.o.
Banjavciceva 11
10 000 Zagreb
CROATIA Telephone +385 (1) 444 444 00
Facsimilie +44(0)208 955 9001

28 | P a g e

DECLARATION OF CONFORMITY

The Manufacturer Tri plus grupa d.o.o. hereby declares that
the product:
Zipabox Smart home controller 1

in accordance with the following Directive(s): 2006/95/EC The
Low Voltage Directive, 89/336/EEC The Electromagnetic
Compatibility Directive and 1999/5/EC R&TT EC Directive

is in conformity with the e applicable requirements of the
following documents:

EN 61326
IEC/EN 55011
EN 300 220-2
EN 61000-3-2
EN 61000-3-3
EN 61000-6-2
EN 61000-4-2
EN 61000-4-3

29 | P a g e

EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
EN 301 489-1-3
AS/NZS/IEC 60335-2-97
EN 60335-1

I hereby declare that the equipment named above has been
designed to comply with the relevant sections of the above
referenced specifications. The unit complies with all
applicable Essential Requirements of the Directives.

Person responsible for this declaration:
Dean Janacek, COO
01.09.2012

30 | P a g e

DISPOSING AND RECYCLING YOUR PRODUCT
This symbol on the product or packaging
means that according to local laws and
regulations this product should be not be
disposed of in the household waste but sent
for recycling. Please take it to a collection
point designated by your local authorities
once it has reached the end of its life, some
will accept products for free. By recycling the
product and its packaging in this manner you help to conserve
the environment and protect human health.
Zipato and the environment
At Zipato, we understand and are committed to reducing any
impact our operations and products may have on the
environment. To minimize this impact Zipato designs and
builds its products to be as environmentally friendly as
possible, by using recyclable, low toxic materials in both
products and packaging.

31 | P a g e

www.zipato.com

…we make every home smart.

32 | P a g e

Zipato zipabox user_guide

More Related Content

What's hot (20)

Viewers also liked (7)

Similar to Zipato zipabox user_guide (20)

More from Domotica daVinci (20)

Zipato zipabox user_guide