D06.VoLTE Interfaces , Protocols & IMS Stack.pdf

VoLTE Interfaces, Protocols & IMS Stack
http://telecomtutorial.info/
1
VOLTE INTERFACES , PROTOCOLS & IMS STACK
This Blog contains Complete VoLTE Protocol Guide which contains details of all Links &
Interfaces working in VoLTE & LTE Networks including their Protocol Stack
 LTE Control Plane Links : S1MME , S5/S8 , S10 , S11 , S6a , Gx , Gy , X2 , SGs
 LTE User Plane Links : S1U , S5/S8 & SGi
 IMS Control Plane links : Sh , Ro , Cx , Rx , Sv , ISC , Mw , Mg , Mi , Mj , Mr / Mr‘ , UT , Ici

2

3
LTE / VoLTE IMS Protocols Interfaces
LTE VoLTE IMS Protocols Interfaces
Here I am going to provide complete Volte Protocol Guide which contains details of all
Links & Interfaces working in VoLTE & LTE Networks
VoLTE Network consists of 3 Network Domains .. 1st One is LTE Network handling user
followed by VoLTE Network & finally Interconnectivity with PSTN or CS Network . Since
LTE or 4G Network is essential part of basic working of VoLTE IMS Network , I have also
included LTE Interfaces , Links & Protocols in this Video to make it more comprehensive in
order to give you complete knowledge
A protocol is a system of digital rules for message exchange between telecom Nodes in
order for one Node to communicate with another . As visible in Diagram , This is a protocol
stack design which shows all the communication Layers for LTE & VoLTE Network .
Three Lower layer stacks consists of 1st Layer as Physical Layer followed by MAC or Data
Link Layer & then IP Layer
From here onward , All communication for LTE & VoLTE is taken care by UDP & SCTP
protocols which are again and again used in Network for Multiple purposes . On Top of
UDP & SCTP Layer , We run various LTE & VoLTE User and control plane links . The
most critical protocols are the Real-time Transport Protocol (RTP) , Diameter , Session
Initiation Protocol (SIP) & Session Description Protocol (SDP)

4
SCTP Vs UDP
SCTP Vs UDP
Let’s discuss two fundamental low layer protocols used in LTE & VoLTE
1st One is SCTP which stands for Stream Control Transmission Protocol which evolved
from TCP . SCTP is used to provide guaranteed message delivery . SCTP is extensively
used as transport layer for carrying telecom signaling over IP. SCTP provides a reliable
transport service that operates at message level . SCTP also allows multiple message
streams to be exchanged on a single SCTP connection.
Key features of SCTP Include :-
 Requires Strong / Robust Media connectivity
 Provides Super Reliable Communication
 Connection-oriented protocol similar to TCP
 Provides facilities such as multi-streaming and multi-homing
 Better performance and redundancy
 S1AP , X2AP , Diameter ( S6 , Gx , Gy )
 Best Suited for Control Plane & Close Reliable Network such as Billing , Charging & Authentications
UDP Stands for User Datagram Protocol which is usually used along with Non Reliable
Media and communication involving multiple Operators such as Roaming etc.. Key
features of UDP Include :-
 Suited for Non-Reliable Media
 Does not guarantee that Data in the order on receive

5
 Minimal message-oriented transport layer protocol
 Enables two hosts to connect and send short messages to one another
 User Plane : S1U , GTPv1U ( S5 , S8 )
 Control Plane : GTPv2C ( S5 , S8 )
 Best Suited for Long Distance & Open Networks such as Roaming etc..
LTE / IMS Protocols Interfaces & links
LTE VoLTE IMS Protocols Interfaces
Here is actual list of Links & Protocols we are going to Cover for LTE & VoLTE User
Plane & Control Plane

6
VoLTE IMS Connectivity Overview
On Left hand side , We can see LTE Network on high level & its components . On Right
hand side , We can see VoLTE IMS Network & Its key components .As you can see in
Blue Circle , I have grouped few functions in IMS
 I-CSCF & S-CSCF are typically deployed within same Server together & they are shown as One
Node
 SBC consists of many critical functions such as P-CSCF , P-CSCF / ATCF / ATGW / IBCF/ TrGW .
They are shown together
 Similarly Media Gateway consists of MGCF / IM-MGW
Here , HSS , OCS & PCRF are 3 main components which are used by both LTE Network
VoLTE Networks for Inter connectivity . Let’s see the High level protocols used in Network
. This all Blue links connecting each other works on SIP Protocol . You can see all SIP to
SIP to SIP communication in entire VoLTE ecosystem . SIP is Chief protocol used for
carrying voice over IP without any limitations . All these Yellow connectivity consists of
Diameter links which are widely used for control plane signaling , Billing , Charging &
Authentication in LTE & IMS Networks

7
SIP & Diameter Protocols
SIP & Diameter Protocols
SIP : Session Initiation Protocol (SIP) is a communications protocol that is widely used
for managing multimedia communication sessions such as voice and video calls. SIP,
therefore is one of the specific protocols that enable voice communication over IP. In a
VoLTE call SIP protocol is used to create, modify and terminate sessions, essentially
negotiating a session between two users. SIP does not perform transport layer (delivering
data) those are done by RTP/RTCP . Key features of SIP Includes :-
 Used for Controlling Voice / Multimedia Calls & Uses RTP / RTCP for media plane
 SIP manages set-up/establishing, tying together, and tear-down/ terminating of multimedia
communications
 5 Functions of SIP :- a) User Location b) User Availability c) User Capabilities d) Session Setup e)
Session Management
Diameter : Diameter is an authentication, authorization, and accounting protocol for
Telecom networks. It evolved from the earlier RADIUS protocol . Key features of Diameter
includes :-
 Evolution of RADIUS (AAA) Protocol – Authentication, authorization, and accounting (AAA) services
 Reliable & Secure ( Runs on TCP / SCTP )
 Supports Failover mechanism to maintain redundancy
 Support for Proxy & Relay Agents
 Support for Capability Negotiation via Mandatory / Optional AVPs
 Provides Dynamic discovery of Peers

8
LTE Network – Protocols & Links
LTE Network – Protocols & Links
Now , Let’s start our journey with base LTE Network . You can see basic Network here
which consists of EnodeB equivalent to Cell Site providing Radio coverage , MME used for
control Plan traffic & handling Mobility of user
SGW / PGW is also called SAE Gateway used for handling user traffic & uplink of same
towards Internet & IMS Network over IP Links
 Key Interfaces for LTE Control includes S1MME , S5/S8 , S10 , S11 , S6a , Gx , Gy , X2 , SGs
 Also there are few user plane links such as S1U , S5/S8 & SGi

9
S6a – LTE Protocols & Links
S6a – LTE Protocols & Links
S6 links connect MME to HSS. This is diameter link and is used by MME for checking
Subscription and authentication data for authenticating/authorizing user access from HSS .
In Simple words , MME download user profile from HSS with help of s6 link such which
APN is allowed or Not ? Whether User can use Internet services or Not ? Whether User
can use IMS VoLTE Services or Not ? Whether these services are allowed on Roaming or
Not ?

10
Gx & Gy – LTE Protocols & Links
Gx & Gy – LTE Protocols & Links
Gx : The Gx interface is between the PCRF and the PGW, This is also diameter link
allowing the PCRF take direct control over the policy enforcement functions of the PGW.
This is used for QOS Management . In simple words , Gx Link is used for enforcing Speed
of users , For Example , 4G Users will be provided 100 Mbps download speed & Once
user consumes all Internet Quota , Speed will be reduced or throttled to 128 kbps by
PCRF over Gx Links
Gy : Gy is between Online Charging System (OCS) and PGW , This is also diameter
link allowing online credit control for service data flow based charging. In simple words ,
This is used for Getting Internet Quota reserved & Decremented on Prepaid System
GTP Interfaces – LTE Protocols & Links

11
GTP Interfaces – LTE Protocols & Links
These GTP Based Interfaces .
S10 : S10 is used for MME to MME connectivity . This is a control interface between the
MMEs which is used for handover & context transfer
S11 : This is the interface between the MME and S-GW in an LTE network . This
handles functions for bearer creation , Deletion , paging coordination & mobility
management
s5/s8 : The S5 interface provides user plane tunneling and tunnel management
between SGW and PGW. This is based on GTP Protocol & is responsible for both Control
and User plane . s5 is Internal to Network whereas s8 is used for Roaming Scenarios

12
S1MME / S1U – LTE Protocols & Links
S1MME , S1U – LTE Protocols & Links
S1 contains two links .. S1 MME & S1U
 S1MME connects EnodeB to MME & is used for control plane signaling
 S1 U – Interface handles S1 user plane data for each bearer between the EnodeB and SGw

13
SGi Link – LTE Protocols & Links
SGi Link – LTE Protocols & Links
SGi : This SGi interface is used between PGw towards internet or IMS Network . This
is highway for Exit traffic from LTE Network

14
SGs Link – LTE Protocols & Links
SGs Link – LTE Protocols & Links
SGs : The SGs interface is used for connectivity between LTE MME to 2G (GERAN) / 3G
(UTRAN) MSCs . Prior to VoLTE launch , This link was playing critical role in 4G Network
by enabling voice via CSFB function & also enabled SMS as well

15
Complete LTE Network – Protocols & Links
Complete LTE Network – Protocols & Links
This diagram shows LTE Network Architecture & Links used in 4G network . Most of
Control plane links are based on Diameter & GTP is used to carry Payload traffic

16
VoLTE IMS Connectivity Overview (2)
Now , We have completed VoLTE Interfaces & Links , Let’s Quickly jump to VoLTE IMS
Interfaces ..

17
VoLTE IMS Connectivity Overview – with IMS Links Highlighted
Above diagram shows connectivity in 4G & IMS VoLTE Network . We are going to
understand each and every link in detail here . Diameter & SIP is prominent protocol used
in IMS network . We will starting with Diameter links and take this journey to SIP links
 IMS Control Plane consists of Sh , Ro , Cx , Rx , Sv , ISC , Mw , Mg , Mi , Mj , Mr / Mr‘ , UT , Ici
 IMS User Plane consists of Gm , SIP , Izi links

18
Rx VoLTE IMS Link
Rx VoLTE IMS Link
 Link : Rx
 Protocol : Diameter
 Specs Reference : 3GPP TS 29.214
 Nodes Connected : PCRF – P-CSCF
 Purpose : Creation of an appropriate policy for a session for Incoming or Outgoing Calls on
Network via PCRF
Rx interface is Bridge between IMS Network & Packet Core . The Rx Interface is used
between the P-CSCF and the PCRF allowing the request of an appropriate policy for a
session for setting up Incoming & Outgoing Voice call . This Rx Interface is used to control
the establishment of any type of Incoming or Outgoing Calls , and thereby authorize and
control resource usage in the access networks . Rx uses Diameter protocol . You can find
more details on Rx Interface under 3GPP TS 29.214 Specs
Typical Messages in Rx includes AA & Auth Request / response / terminate between P-
CSCF & PCRF . Other Messages getting exchanged on Cx Interfaces are :-
 AA-Request (AAR)
 AA-Answer (AAA)
 Re-Auth-Request (RAR)
 Re-Auth-Answer (RAA)
 Session-Termination-Request (STR)
 Session-Termination-Answer (STA)

19
 Abort-Session-Request (ASR)
 Abort-Session-Answer (ASA)
Cx VoLTE IMS Link
Cx VoLTE IMS Link
 Link : Cx
 Specs Reference : 3GPP TS 29.228 , 29.229
 Nodes Connected : I/S-CSCF – HSS
 Purpose : I/S-CSCF communicates with HSS to get user profile , Supports in user registration
& Authentication
You can find more details on Cx Interface under 3GPP TS 29.228 Specs . The Cx
Interface is used between the I/S CSCF and HSS for downloading Subscriber data to the
S-CSCF from HSS . It enable IMS registration and passing of subscriber data to the S-
CSCF. Cx uses Diameter protocol .
Typical Messages in Cx includes UAR / MAR / SAR used during Registration of IMS User
in Network . For Instance , I-CSCF talks to HSS to get the detailed subscriber information
for the User Authentication . S-CSCF send MAR (Multimedia Authentication Request) to
HSS as part of an initial IMS registration with IMS-AKA related security . The S-CSCF also

20
performs the SAR (Server Assignment Request) procedure to the HSS to download the
relevant user profile and register the VoLTE UE. The S-CSCF stores the route header of
the P-CSCF and binds this to the contact address of the VoLTE UE, this is used for routing
to the VoLTE UE in future messages
Other Messages getting exchanged on Cx Interfaces are :-
 User-Authorization-Request( UAR)
 User-Authorization-Answer(UAA)
 Server-Assignment-Request(SAR)
 Server-Assignment-Answer(SAA)
 Location-Info-Request(LIR)
 Location-Info-Answer(LIA)
 Multimedia-Authentication-Request(MAR)
 Multimedia-Authentication-Answer(MAA)
 Registration-Termination-Request(RTR)
 Registration-Termination-Answer(RTA)
 Push-Profile-Request(PPR)
 Push-Profile-Answer(PPA)
Sh VoLTE IMS Link
Sh VoLTE IMS Link

21
 Link : Sh
 Specs Reference : 3GPP TS 29.328 , 29.329
 Nodes Connected : TAS – HSS
 Purpose : TAS download user profile from HSS and enables service for user
You can find more details on Sh Interface under 3GPP TS 29.328 Specs . The Sh
Interface is used between the TAS and HSS to Support exchange of User Profile
information such as service related information, user location information or charging
function info . It enable service and subscriber related information to be passed from HSS
to TAS . This is somehow Equivalent to Location Update between HSS & TAS . Sh uses
Diameter protocol . Typical Messages in Cx includes UDR / UDA used during Registration
of IMS User in Network :-
 User-Data-Request(UDR)
 User-Data-Answer(UDA)
 Profile-Update-Request(PUR)
 Profile-Update-Answer(PUA)
 Subscribe-Notifications-Request(SNR)
 Subscribe-Notifications-Answer(SNA)
 Push-Notification-Request(PNR)
 Push-Notification-Answer(PNA)

22
Ro VoLTE IMS Link
Ro VoLTE IMS Link
 Link : Ro
 Nodes Connected : TAS – OCS
 Purpose : TAS communicates with OCS & Prepaid Platform for Online charging of Voice Calls
For any voice call , The charging function needs to perform credit control before allowing
call to mature . With help of Ro Interface , TAS communicate with OCS Platform which
perform Online charging of call . Ro Interface also works on Diameter protocol
For Operators , where Ro Interface is not supported on OCS or IN , As alternative SS7
based CAMEL Protocol is also used . With CAMEL Interface , Volte Charging is done in
similar way as done in Circuit Core Network with help of SS7 Protocol

23
Gm SIP VoLTE IMS Link
Gm SIP VoLTE IMS Link
 Link : Gm
 Protocol : SIP/SDP
 Nodes Connected : UE – P-CSCF
 Purpose : Enables connectivity between the UE and the IMS network for registration,
authentication, encryption, and session control
Gm Interface is key to all User based communication . The Gm Interface is used between
the UE (User) and P-CSCF for all purpose viz .. Registration / De-Registration / Incoming
– Outgoing Calls / SIP Signaling / or any type of communication between User to IMS
Network . For security reasons, the Gm and Mw Interfaces are physically separate. This
Interface also carries Authentication, encryption, and complete session control. Gm uses
SIP & SDP protocol

24
Mw SIP VoLTE IMS Link
Mw SIP VoLTE IMS Link
 Link : Mw
 Nodes Connected : x-CSCF – x-CSCF
 Purpose : Used to exchange messages between CSCFs ( Ex : P-CSCF to S-CSCF )
The Mw Interface is used between a CSCF Nodes to another CSCF Node within the IMS
core network . Typically SBC Hosts P-CSCF which gets connected to I/S-CSCF via this
Mw Protocol . Mw uses SIP and SDP Protocols for enabling these connectivity . You can
find more details on Mw Interface under 3GPP TS 24.229

25
Mx SIP VoLTE IMS Link
Mx SIP VoLTE IMS Link
 Link : Mx
 Nodes Connected : x-CSCF – IBCF
 Purpose : Used for the interworking with another IMS network, This is used by CSCF to send
SIP message from BGCF to the IBCF in the other network
This is Mx Interface which is used between CSCF and IBCF . It plays vital role for the
interworking with another IMS network. It Provides interworking with another IMS network
when the BGCF has determined that a breakout should occur into the other IMS network.
This Carries SIP message from the BGCF to the IBCF in the other network . The protocols
used on the Mx Interface are SIP and SDP and are defined in 3GPP TS 24.229

26
Mg SIP VoLTE IMS Link
Mg SIP VoLTE IMS Link
 Link : Mg
 Nodes Connected : xCSCF – MGCF
 Purpose : Enables Interworking with Circuit Switched Network to the CSCF
The Mg Interface is used to convey SIP messages between an S/I-CSCF and an MGCF
for signaling purposes . This is used for exchanging Signaling between CSCF & Media
Gateway for Call coming and Going towards Circuit core Networks . This Interface also
works on SIP and SDP protocols defined in 3GPP TS 24.229 specs

27
Mi SIP VoLTE IMS Link
Mi SIP VoLTE IMS Link
 Link : Mi
 Nodes Connected : xCSCF – BGCF
 Purpose : Serving CSCF to forward the SIP/SDP messages to the Breakout Gateway Control
Function for the purpose of MGCF selection for interworking with Circuit Switched networks
Mi Interface is also based on SIP & is specific under 3GPP TS 24.229 Specs . The Mi
Interface is used to Exchanges messages between S-CSCF and BGCF for interworking
with the PSTN . It allows the Serving CSCF to forward the SIP/SDP messages to the
Breakout Gateway Control Function for the purpose of MGCF selection for interworking
with Circuit Switched networks

28
Mj SIP VoLTE IMS Link
Mj SIP VoLTE IMS Link
 Link : Mj
 Nodes Connected : BGCF – MGCF
 Purpose : Allows the Breakout Gateway Control Function to exchange SIP/SDP messages
with the MGCF for the purpose of interworking with Circuit Switched networks
This another BGCF based Interface between BGCF & MGCF . This is used to convey SIP
messages between a BGCF and an MGCF for interworking with Circuit Switched networks
. It carries Exchange of sessions with an MGCF that the BGCF has selected to provide
session breakout to the PSTN or Circuit Switched Networks . The protocols used on the Mj
interface are SIP and SDP and are defined in 3GPP TS 24.22

29
ISC SIP VoLTE IMS Link
ISC SIP VoLTE IMS Link
 Link : ISC
 Nodes Connected : SCSCF –TAS
 Purpose : SCSCF Interact with the MMTel supplementary services implemented on the TAS
The ISC interface is another SIP based connectivity defined under 3GPP TS 24.229 . This
enables connectivity between S-CSCF and TAS (Telephony Application Server) . This ISC
Interface interacts with the MMTel supplementary services implemented on the TAS where
IMS Service Control Interface is used for requesting services from an TAS. It also supports
TAS initiated requests to the IMS

30
Mr & Mr’ VoLTE IMS Link
Mr & Mr’ VoLTE IMS Link
 Link : Mr & Mr’
 Specs Reference : 3GPP TS 24.229 , 3GPP TS 24.880
 Nodes Connected :
 Mr : SCSCF – MRF
 Mr’ : TAS – MRF
 Purpose : Allow interaction with the media resource for specific supplementary services (e.g.
conference call)
As you are aware , MRF deals with Announcement & Media related functionalities such as
transcoding, multiparty conferencing, network announcements/tones, etc. . There are 2
Interfaces providing MRF connectivity to SCSCF & TAS . First One is Mr interface
between MRF to S-CSCF and 2nd One is Mr’ ( Mr Apostrophe ) interface between MRF
and TAS (Telephony Application Server) . These interfaces allow interaction with the
media resource for specific supplementary services (e.g. conference call) on Control Plane

31
Ut XCAP VoLTE IMS Link
Ut XCAP VoLTE IMS Link
 Link : Ut
 Protocol : XCAP
 Nodes Connected : UE – TAS
 Purpose : Allows user configuration of the supplementary services specified for VoLTE
service to Handset Directly
Ut runs on XCAP protocol which Stands for eXtensible Markup Language (XML)
Configuration Access Protocol (XCAP) . This Ut Interface is used between the User
Equipment and the TAS and allows user configuration of the supplementary services
specified for VoLTE . The protocol used on the Ut Interface is XCAP . This is defined in
3GPP TS 24.623 & IETF RFC 4825 specs

32
Sv VoLTE IMS Link (GTPv2)
Sv VoLTE IMS Link (GTPv2)
Sv : Sv is a new special SV interface is introduced between the MME and the MSC to
support SRVCC functionality . This runs on GTPv2 protocol . Refer to my another Blog on
SRVCC for more details of this link & functionality

D06.VoLTE Interfaces , Protocols & IMS Stack.pdf

More Related Content

What's hot (20)

Similar to D06.VoLTE Interfaces , Protocols & IMS Stack.pdf (20)

Recently uploaded (20)

D06.VoLTE Interfaces , Protocols & IMS Stack.pdf