ADVANCED SERVICE DATA PROVISIONING FOR REAL-TIME MANAGEMENT OF ONGOING CELLULAR COMMUNICATION NETWORKS

International Journal of Computer Networks & Communications (IJCNC) Vol.14, No.3, May 2022
DOI: 10.5121/ijcnc.2022.14307 107
ADVANCED SERVICE DATA PROVISIONING FOR
REAL-TIME MANAGEMENT OF ONGOING
CELLULAR COMMUNICATION NETWORKS
Mikhail E. Belkin1
, Leonid Zhukov1
,
Alexander S. Sigov1
and Mikhail G. Vasil’ev2
1
Russian Technological University MIREA, Moscow, Russia
2
Kurnakov Institute of General and Inorganic Chemistry of the RAS, Moscow, Russia
ABSTRACT
A new cost-efficient concept to realize real-time management and monitoring of quality-of-service metrics
and other service data in 5G and beyond access network using a separate return channel based on a
vertical cavity surface emitting laser in the optical injection locked mode that simultaneously operates as a
laser source and a resonant cavity enhanced photodetector, is proposed and discussed. The feasibility and
efficiency of the proposed approach are investigated and confirmed by a proof-of-concept experiment when
optically transceiving high-speed digital signals with multi-position quadrature amplitude modulation of a
radio-frequency carrier.
KEYWORDS
5G and beyond, RoF-based radio access network, real-time monitoring, QoS metrics, bimodal OIL-
VCSEL.
1. INTRODUCTION
In recent years, with the maturing of 5G NR systems, the design of access networks (AN) has
acquired some significant changes. In particular, the centralized radio access network (C-RAN)
that passed from the 4G-LTE network, where interface connects various small cells deployed as
remote radio heads (RRHs) to a centralized macro-cell deployed as a baseband unit (BBU) [1, 2],
was standardized [3] into the next generation RAN (NG-RAN). Following it, some newer
functional blocks, such as a central unit (CU), a distributed unit (DU), and a radio unit (RU) were
introduced considered in detail in [4]. The key reason for this transformation was the use of the
Common Public Radio Interface (CPRI) with time division multiplexing (TDM) between the
BBU and RRH [4]. This approach led to data transfer rates up to hundreds of Gbps, which makes
this interface economically unjustified for 5G and beyond. Figure 1 depicts a typical architecture
of NG-RAN, where CU, DU, and a set of RUs are duplex connected via fiber-optics
communication lines (FOCLs), while RUs and mobile user terminals (UTs) intercommunicate
wirelessly.
Generally, as optical networks are evolving to fulfil highly flexible connectivity and dynamicity
requirements, and to support ultra-low latency services, it is increasingly important that NG-RAN
also provides reliable connectivity and improved network resource efficiency. For this goal, a
collection of different types of data from various sources is necessary for applying automation
techniques to network management. However, the network must also support the capability to
extract knowledge and form perception for performance monitoring and troubleshooting, as well

108
as to maintain network service continuity over a wide range of elements at various levels. Such
scalability and flexibility are particularly important for the wide area network, in particular, for
streaming telemetry [5]. Moreover, an efficient optical performance monitoring (OPM) design
should consider different scenarios including large-scale disaster [6], when a prompt reaction is
needed but limited bandwidth is available now.
Figure 1. Conceptual block-diagram of 5G’s NG-RAN
Projecting the above problem that is common for telecom networks, for the purpose of this paper,
we can conclude that in the newer generation, ANs providing the function of low-cost real-time
monitoring and the quality-of-service (QoS) metrics are a matter of great importance from the
point of view of their maintenance. In this case, the issue can be solved by additionally
introducing a special node into the DU circuit (see Fig. 1), which is responsible for the
accumulation and processing of monitoring results. However, a more promising solution from the
point of view of reducing the total cost and latency, in our opinion, might be the introduction of
an additional function from the existing indispensable element of its circuitry, return transmission
of the optical signal to the CU, and its processing there. A promising technique for implementing
this approach through the simultaneous use of a long-wavelength Vertical Cavity Surface
Emitting Laser (VCSEL) in optically injection-locked mode (OIL-VCSEL) as a laser source and
a resonant cavity enhanced photodetector (RCE-PD) was proposed in [7] for bidirectional optical
communication and recently developed by us [8] referred to microwave photonics circuits.
Elaborating the approach, in this paper after reviewing the modern service provisioning
techniques in ongoing optical networks in Section 2, a newer design concept of OIL-VCSEL-
based transmitter/receiver, which receives information data from CU via the downlink channel,
and simultaneously re-transmits them to RUs and via the uplink channel for processing at CU, is
proposed and discussed in Section 3. The feasibility and efficiency of the proposed solution are
investigated in Section 4 and confirmed in Section 5 by a proof-of-concept experiment, when
optically transmitting a high-speed digital signal with 64-position quadrature amplitude
modulation (QAM) of a 5-GHz radio frequency (RF) carrier. Section 6 concludes the paper.
2. MODERN TENDENCIES TO SERVICE PROVISIONING IN ONGOING NG-
RANS
With the development of techniques and technologies of 5G NR networks, it became clear that
this is not just a new standard for mobile communications. In general, the widespread worldwide

109
introduction of core and access networks of the 5th and subsequent generations in the long term
should transform our worldview and lead to a social transformation of the world community,
radically changing the principles of communication, architecture, economy, and the level of
service of local and global telecom networks. For this purpose, known and new cellular
communications concepts, paradigms, approaches, scenarios, technologies, mechanisms, tools,
and services are being developed. In particular, they include noted in Introduction NG-RANs,
Radio-over-Fiber (RoF)-based mobile backhauls/fronthauls, as well as Enhanced Mobile
Broadband (eMMB) [9], Ultra-Reliable Low Latency Communication (URLLC) [10], Massive
Machine-Type Communications (mMTC) [11], Internet of Everything [12], Slice-based
Networks for Heterogeneous Environments [13], Software Defined Networking (SDN) [14],
Network Function Virtualization (NFV) [15] and so on.
The results of the above innovations should lead to significant improvements in the QoS and key
parameters of NG RANs. Thus, the recommendation 3GPP TR 38.913 identified the following
outstanding key indicators of new generation networks:
 downlink peak data rate up to 20 Gbps with spectral efficiency 30 bps/Hz
 uplink peak data rate up to 10 Gbps with spectral efficiency 15 bps/Hz
 the minimum delay in the radio access subsystem for URLLC services is 0.5 ms, for
eMBB services - 4 ms
 the maximum density of the IoT devices connected to the network in urban territories
is 1'000'000 devices/sq. km
 autonomous operation of the IoT devices without recharging the battery for 10 years;
 vehicle mobility at a maximum speed of 500 km/h.
Along with these, a critical problem arose related to ensuring the above parameters during the
maintenance of realistic NG-RANs through the development of advanced operational principles,
approaches, and schemes. In general, advanced monitoring framework of optical networks aimed
at the continuous, remote, automatic and cost-effective supervision of the physical layer has to
satisfy the basic set of the requirements:
(i) fast and accurate detection of the performance degradation and service disruptions
(ii) accurate track down location of the network failure
(iii) monitoring should be non-intrusive and do not affect normal network operation
(iv) compatible with various types of optical networks.
Besides, to meet the goals of 5G NG and beyond, network infrastructures should facilitate a high
level of flexibility and automation. In particular, monitoring and data analytics give rise to
estimate accurately the QoS of new light paths anticipating capacity exhaustion and degradations,
or predicting and localizing failures, among others to facilitate this automation [16]. At the same
time, network operations and management (OAM) should increasingly rely on the ability to
stream and process real-time data from network equipment. An integral part of the OAM is to
make sure whether the operational conditions are normal or not and intervene, if needed, by
quickly recovering and mitigating the occurred problems [17]. The goal to have network
management automation and abstraction of open line systems (OLS) could be possible by the
software-defined network (SDN) technologies, which require accurate OPM data from the
elements of the network [18].

110
3. DESIGN CONCEPT
Based on the results of the review in Section 2, it can be unambiguously concluded that any
existing approach to monitoring the QoS of a FOCLs leads to the complication of the DU
circuitry and operation, and consequently to the increase in its cost and the latency of signal
transmission via the AN. Therefore, the solution related to the introduction of an additional
function to the existing indispensable element of its circuitry, namely the simultaneous use of an
OIL-VCSEL as a laser source and a RCE-PD, is promising in principle.
Revealing the proposed concept, Figure 2 demonstrates a block diagram of a communication
channel, containing all three functional units of NG-RAN (see Figure 1). It is worth noting that
the block-diagram presented in this Figure has three key distinguishing features according to NG-
RAN concept. Firstly, at the CU, in order to simplify the circuitry of subsequent units, the
conversion of the modulation format of the optical carrier from a baseband (BB) to QAM of RF
subcarrier is performed so that the digital signal is then transmitted over FOCLs using a RF equal
to the allocated frequencies of the corresponding RU [19]. Secondly, a duplex optical channel is
introduced between the CU and DU, where the information signal is transmitted in the downlink
direction, and the QoS data signal - in the uplink direction. Thirdly, in the DU, an OIL-VCSEL is
connected through an optical circulator, where reflected optical output is transmitted via
downlink to the RU, and the detected RF signal with added QoS data is again converted into the
optical range using a standard low-cost optical transmitter and returned to the CU for the
subsequent processing.
Figure 2. Block-diagram of the proposed duplex communication channel for NG-RAN, where SLS, OM,
OAM, DSP, OR, OT, PD, LN-RFA, BPF, and PA stand for semiconductor laser source, optical modulator,
optical amplifier, digital signal processor, optical receiver, optical transmitter, photodetector, low-noise RF
amplifier, bandpass RF filter, and power RF amplifier (Optical connections are painted in red, electrical
connections – in black)

111
4. DYNAMIC FEATURES OF BIMODAL VCSEL
4.1. Intrinsic direct modulation features of the VCSEL under test
First, in order to select the optimal DC bias point and further comparison, the intrinsic dynamic
features of the long-wavelength VCSEL under test operating in free-running mode, are
investigated. Figure 3 depicts a testbed for measuring small-signal gain of the directly modulated
VCSEL vs the RFs of 0.1-10 GHz at various forward bias currents.
Figure 3. Testbed for studying intrinsic direct modulation characteristics of the VCSEL, where Bias-T, DC,
PD, and RF VNA stand for Bias Tee, Direct Current Source, Reference Photodiode, and Radio-Frequency
Vector Network Analyzer (Optical connections are painted in red, electrical connections – in black)
The testbed contains a measuring circuit including the direct modulated wafer-fused VCSEL
under test (Beam Express, LLC, Switzerland, operating wavelength near 1561 nm) and the
reference photodiode (G&H EM169, 20-GHz bandwidth, 0.8-A/W responsivity), as well as
accessories such as Bias Tee (Pasternack PE1606, 0.1-MHz…12-GHz bandwidth), and a
measuring instruments such as RF Vector Network Analyzer (Keysight PNA-X N5244B) and
corresponding DC current source. It should be noted that in current and subsequent studies of this
work, the VCSEL in a chip format is used as an object of testing. In this connection, all
measurements are carried out on the Probe Station EP6 from Cascade Microtech by a workbench
including thermo-electrical cooler for temperature controlling, coplanar RF probe, and fiber-
optics probe, which is described in detail in [8].
Figure 4 presents the small-signal gain vs RF characteristics measured by the testbed of Fig. 3.

112
Figure 4. Measured direct modulation characteristics of the VCSEL under test at the bias currents of 4 mA
(olive), 5 mA (blue), 6 mA (pink), 8 mA (green) and 10 mA (brown)
As one can see from the Figure, the -3dB modulation bandwidth progressively expands as the
bias current increases, reaching from 2.5 GHz at 4 mA to 5.7 GHz at 10 mA.
4.2. Information channel of the proposed concept (OIL-VCSEL in Laser Mode)
Figure 5 depicts a testbed for measuring dynamic characteristics of the Information channel of
Fig. 2, where OIL-VCSEL operates in a laser mode. The testbed, besides the tunable
semiconductor laser (PurePhotonics PPCL300, 1530-1565-nm wavelength range, 6-13.5-dBm
power range) as a master laser, the OIL-VCSEL under test with 6-mA direct current bias as a
slave laser, and the reference PD (Finisar XPDV3120, 70-GHz bandwidth, 0.6-A/W
responsivity), contains a set of accessories and measuring tools. The latter include Erbium-doped
fiber amplifier (home-made, 1530-1565-nm wavelength range, 4-20-dBm output power range,
10-dBm maximum input power, 4-20 dB gain range), optical circulator (Opneti, CIR-3-1550),
RF bias-T (Pasternack, PE1BT-1002, 40-GHz bandwidth) as well as corresponding DC current
source and RF vector network analyzer (Keysight PNA-X N5244B).
Figure 5. Testbed for measuring dynamic characteristics of the Information channel, where TSL, EDFA,
OCL, PD, VNA, and DC stand for tunable semiconductor laser, erbium-doped fiber amplifier, optical
circulator, reference photodiode, RF vector network analyzer, and direct current power supplier,
respectively. (Optical connections are painted in red, electrical connections – in black)

113
Figure 6 presents the small-signal gain frequency characteristics at the VCSEL’s bias current of 6
mA measured by the testbed of Fig. 5. As one can see from the Figure, the introduction of OIL
led to the expansion of the Information channel’s -3dB bandwidth to 35.8 GHz with the EDFA
output power of 20 dBm (red curve). For comparison, the Figure also shows the intrinsic gain vs
RF characteristic of the VCSEL at the same current as in Figure 4 (blue curve), where the -3dB
bandwidth is only 4.3 GHz.
Figure 6. Measured small-signal gain vs RF frequency characteristics of the Information channel, when
OIL-VCSEL operates in a laser mode. The markers 1, 2 indicate, respectively: -3dB bandwidth at EDFA
output power of 20 dBm and the case of OIL off
4.3. Service channel of the proposed concept (OIL-VCSEL in RCE-PD Mode)
Figure 7 depicts a testbed for measuring dynamic characteristics of the Service channel of
Fig. 2, where OIL-VCSEL operates in a RCE-PD mode. The testbed, besides the OIL-VCSEL
under test operating at the same direct current bias as in a laser mode and the same master laser
(see Fig. 5), contains a set of accessories and measurement tools. The latter includes the external
optical modulator (ThorLabs LN05S-FG, 1525-1605-nm wavelength range, 5-dB insertion loss,
35-GHz RF bandwidth), the same EDFA, OCL, bias-T, DC, and VNA as in Fig. 5, as well as
Optical Spectrum Analyzer (Yenista OSA20) for real-time monitoring of the emitted spectrum of
the OIL-VCSEL under test.
Figure 7. Testbed for measuring dynamic characteristics of the Service channel, where TSL, OM, EDFA,
OCL, VNA, DC and OSA stand for the tunable semiconductor laser, optical modulator, erbium-doped fiber
amplifier, optical circulator, RF vector network analyzer, direct current source, and optical spectrum
analyzer, respectively. (Optical connections are painted in red, electrical connections – in black)

114
Figure 8 presents the small-signal gain frequency characteristics measured by the testbed of
Fig. 7. As one can see from the Figure, the introduction of OIL led to the expansion of the
Service channel’s -3dB bandwidth to 20.5 GHz with the EDFA output power of 16 dBm (red
curve) and up to 27.3 GHz at 20 dBm (blue curve). For comparison, the Figure shows the RF
response of the RCE-PD with OIL off (pink curve), where the -3dB bandwidth is only 4.5 GHz.
Figure 8. Measured small-signal gain vs RF frequency characteristics of the Service channel. The markers
1, 2, 3 indicate, respectively: -3dB bandwidth at EDFA output power of 16 dBm, the same at 20 dBm, and
the case of OIL off
The following outcomes can be drawn from the above results:
 The introduction of OIL led to more than 8-fold expansion of the Information
channel’s RF bandwidth at the EDFA output power of 20 dBm.
 The introduction of OIL led to a 4.5-fold expansion of the Service channel’s RF
bandwidth at the EDFA output power of 16 dBm and to a 6-fold increase at its power
of 20 dBm.
As a result, due to the expansion of the RF bandwidth, the proposed duplex communication
channel for NG-RAN using bimodal VCSEL under study is able to operate effectively not only in
the microwave band but also in the millimeter-wave band without using RF up/down converters,
in particular, in the 24-27 GHz band allocated for the 5G NR’s NG-RAN network.
5. PROOF-OF-CONCEPT EXPERIMENT
To validate the proposed concept a laboratory experiment was realized where a wafer-fused long-
wavelength vertical cavity surface emitting laser of RTI Research, LLC in the form of a chip that
is optically injection-locked by a master laser, was used. The purpose of the experiment is to
confirm the functionality and effectiveness of the block-diagram of a duplex communication
channel for NG-RAN described in the Section 3, when optically transmitting a high-speed digital
signal with multi-position QAM of a RF carrier. Note that during the experiment the OIL-VCSEL
operates in forward DC biased mode without switching to reverse DC bias in photodetector mode
as required with a standard pin-photodiode, which is ensured by optical injection locking [8].
Figure 9 shows the testbed for proof-of-concept experiment, the layout of which is based on Fig.
2 with the exclusion of non-essential for the confirmation elements after points A and B. The
testbed contains the pin-photodiode (Finisar, BPDV2150: 43-GHz bandwidth, 0.6-A/W
responsivity), a pair of low-noise RF amplifiers (Mini-circuits ZX60-542LN-S+: 4.4-5.4-GHz

115
frequency band, 24-dB gain, 1.9-dB noise figure), and two coils of single-mode fibers
SMF-28+, as well as measuring tools including Vector Signal Generator (Keysight MXG
N5182B) and 4-channel Mixed Signal Oscilloscope (Keysight Infinium MSOS804A).
Figure 9. Testbed for the proof-of-concept experiment where TSL, OM, EDFA, OCL, OF, PD, LNA, DC,
VSG, and MSO stand for tunable semiconductor laser (master laser), optical modulator, erbium-doped
fiber amplifier, optical circulator, optical fiber, photodetector, low-noise amplifier, DC source, vector
signal generator, and real-time oscilloscope, respectively. (Optical connections are painted in red, electrical
connections – in black)
Figure 10 presents the results of the experiment, where optical carrier of the frequency near 192.2
THz is intensity modulated by the 560 Mbps 64-QAM RF signal of 5 GHz. Namely, in Figures
10 (a, b), MSO RF spectra are shown at the inputs 1 and 2, correspondingly. Figure 10 (c) shows
the constellation diagram at the input 1 or 2 of the MSO, and Figure 10 (d) shows EVM values vs
OF1 length at the inputs 1 and 2 of the MSO.
(a) RF spectrum at the input 1 of the MSO

116
(b) RF spectrum at the input 2 of the MSO
(c) The constellation diagram at the input 1 or 2 of the MSO
(d) EVMs vs OF1 length at the inputs 1 and 2 of the MSO
Figure 10. The results of the proof-of-concept experiment
The outcome that can be drawn from the above results is the following. Leveraging the proposed
concept to the NG-RAN block-diagram of Fig. 1, in the DU, the values of error vector magnitude
in back-to-back configuration are 3.2% for downlink channel to RU and 4.3% for uplink channel
to CU, which is significantly less compared to the standard EVM threshold for 64-QAM of 8%
[20]. This maximum acceptable transmission quality is achieved, when the distance between CU
and DU is increased up to 5 km, which is quite realistic in a practical 5G access network based on
small cell concept.

117
6. CONCLUSIONS
In this paper, a new cost-efficient concept to realize real-time management and monitoring of
quality-of-service metrics and other service data in 5G and beyond access networks using a
small-cell architecture is proposed and discussed. The essence of the proposed solution is
investigated in detail on the example of a block diagram of a duplex communication channel,
including a microcell base station and a functionally split picocell base station containing a
central unit, a distribution unit, and a set of remote radio units each connected via optical fiber
link. A distinctive feature of the proposed approach, which provides an improvement in the
power and cost characteristics, is to use a vertical cavity surface emitting laser in the optical
injection locked mode that simultaneously operates as an optical emitter and as a resonant cavity
enhanced photodetector. Thanks to this, it becomes possible to transmit information data to a
distribution unit via the downlink channel and real-time service data related to the status, quality
of service, etc. via uplink channel for processing them at the central unit. The feasibility and
efficiency of the proposed solution are confirmed by a proof-of-concept experiment when
optically transmitting a high-speed digital signal with 64-position quadrature amplitude
modulation of a 5-GHz radio-frequency carrier, which is widely exploited in access networks of
fifth-generation cellular communication systems based on Radio-over-Fiber technology and small
cell architecture scenario.
Our further research in this direction will focus on a detailed studying the VCSEL-based optical
transmission with real-time monitoring function for ongoing 5G and beyond access networks of
millimeter-wave band. The reality of such a path was confirmed in this paper. In addition, the
fundamental ability to achieve an operating bandwidth of more than 100 GHz due to optical
injection locking has already been considered in a number of scientific publications.
ACKNOWLEDGMENT
This work was supported by the Russian Foundation for Basic Research, Grant No. 18-29-20083.
The authors are grateful to Beam Express, LLC for providing laser samples.
CONFLICTS OF INTEREST
The authors declare no conflict of interest.
REFERENCES
[1] G. Pandey, A. Choudhary, and A. Dixit, “Radio over Fiber Based Fronthaul for Next-Generation 5G
Networks,” Proceedings of 22nd International Conference on Transparent Optical Networks
(ICTON), Bari, Italy, July 19-23, p. 1-4, 2020.
[2] M. Kamalian-Kopae, M. E. Belkin, and S. K. Turitsyn, “The Design Principles of Fibre-Wireless
Integration in the Incoming Mobile Communication Networks,” Proceedings of 22nd International
Conference on Transparent Optical Networks (ICTON 2020), Bari, Italy, July 19-23, p. 1-4, 2020
[3] “Study on new radio access technology: radio access architecture and interfaces,” 3GPP Technical
Report TR38.801, v14.0.0, 2017.
[4] J. Zou, S. A. Sasu, M. Lawin, A. Dochhan, J.-P. Elbers, and M. Eiselt, “Advanced optical access
technologies for next-generation (5G) mobile networks,” Journal of Optical Communications and
Networking, Vol. 12, No. 10, p. D86-D98, October 2020.
[5] A. Sadasivarao, et al. "High performance streaming telemetry in optical transport networks." Optical
Fiber Communication Conference. Optical Society of America, 2018
[6] S. Xu, et al. "Emergency OPM recreation and telemetry for disaster recovery in optical networks,"
Journal of Lightwave Technology, vol. 38, No 9, p. 2656-2668, May 2020.

118
[7] Q. Gu, W. Hofmann, M.-C. Amann, L. Chrostovski, “Optically Injection-Locked VCSEL for Bi-
directional Optical Communication,” 2008 Conference on Lasers and Electro-Optics (CLEO2008), p.
1-2, 2008.
[8] M. E. Belkin, L. I. Zhukov, D. A. Fofanov, M. G. Vasil’ev, and A. S. Sigov. “Studying a LW-
VCSEL-Based Resonant Cavity Enhanced Photodetector and its Application in Microwave Photonics
Circuits,” Chapter in IntechOpen book “ Light-Emitting Diodes and Photodetectors - Advances and
Future Directions”, 2021, 20 pp. https://www.intechopen.com/online-first/studying-a-lw-vcsel-based-
resonant-cavity-enhanced-photodetector-and-its-application-in-microwave-ph
[9] Li-Sheng Chen, et al. “AMC With a BP-ANN Scheme for 5G Enhanced Mobile Broadband,” IEEE
Access, Sept. 2020, DOI: 10.1109/ACCESS.2020.3024726.
[10] B. Singh, O. Tirkkonen, Z. Li and M. A. Uusitalo, "Interference Coordination in Ultra-Reliable and
Low Latency Communication Networks," 2018 European Conference on Networks and
Communications (EuCNC), 2018, pp. 1-255, doi: 10.1109/EuCNC.2018.8443229.
[11] S. Chae, S. Cho, S. Kim and M. Rim, "Coded random access with multiple coverage classes for
massive machine type communication," 2016 International Conference on Information and
Communication Technology Convergence (ICTC), 2016, pp. 882-886, doi:
10.1109/ICTC.2016.7763321.
[12] S. Higginbotham, "Network included - [Internet of Everything]," in IEEE Spectrum, vol. 57, no. 11,
pp. 22-23, Nov. 2020, doi: 10.1109/MSPEC.2020.9262153.
[13] Peng Xu, Xiaqi Liu, Z. Sheng, Xuan Shan and Kai Shuang, "SSDS-MC: Slice-based Secure Data
Storage in Multi-Cloud Environment," 2015 11th International Conference on Heterogeneous
Networking for Quality, Reliability, Security and Robustness (QSHINE), 2015, pp. 304-309.
[14] T. Theodorou and L. Mamatas, "CORAL-SDN: A software-defined networking solution for the
Internet of Things," 2017 IEEE Conference on Network Function Virtualization and Software
Defined Networks (NFV-SDN), 2017, pp. 1-2, doi: 10.1109/NFV-SDN.2017.8169870
[15] S. Bijwe, F. Machida, S. Ishida and S. Koizumi, "End-to-End reliability assurance of service chain
embedding for network function virtualization," 2017 IEEE Conference on Network Function
Virtualization and Software Defined Networks (NFV-SDN), 2017, pp. 1-4, doi: 10.1109/NFV-
SDN.2017.8169853
[16] A. Sgambelluri, et al. "Exploiting Telemetry in Multi-Layer Networks," 22nd International
Conference on Transparent Optical Networks (ICTON), 2020.
[17] V.-M. Alevizaki, et al. "Joint fronthaul optimization and SDN controller placement in dynamic 5G
networks." International IFIP Conference on Optical Network Design and Modeling. Springer, Cham,
2019.
[18] W.-K. Jia, et al. "A Survey on All-Optical IP Convergence Optical Transport Networks," 2019 7th
International Conference on Information, Communication and Networks (ICICN). IEEE, 2019
[19] M. E. Belkin, T. Bakhvalova, and A.C. Sigov, “Design Principles of 5G NR RoF-Based Fiber-
Wireless Access Network”; In book “Recent Trends in Communication Networks”, IntechOpen,
London, UK, p. 121-145, 2020. DOI: 10.5772/intechopen.90074.
[20] ETSI, "Minimum requirements for Error Vector Magnitude," in TECHNICAL SPECIFICATION,
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) radio
transmission and reception (3GPP TS 36.101 version 14.3.0 Release 14), ETSI, 2017-04, p. 215

119
AUTHORS
Prof. Dr. Mikhail E. Belkin - received an engineering degree in radio and television
from Moscow Institute of Telecommunications, in 1971, Ph. D. degree in
telecommunication and electronic engineering from Moscow Technical University of
Telecommunications and Informatics, in 1996, and Sc. D. degree in photonics and optical
communications from Moscow State Technical University of Radio-Engineering,
Electronics and Automation, in 2007. The theme of his Sc. D. degree thesis is ‘Analog
Fiber Optic Systems with multiplexing on RF and Microwave Subcarriers and
Multiservice HFC Networks on their Base’. He has written more than 250 scientific
works in English and Russian. The major current R&D fields are fiber-optic devices and systems,
microwave photonics, photonic ICs, incoming cellular communication networks, computer-aided design.
At present, M. E. Belkin is the Director of the Scientific and Technological Center “Integrated Microwave
Photonics”, Professor of the department “Optical and Optoelectronic Devices and Systems”, Institute of
Physics and Technology, MIREA - Russian Technological University, and he is a member of IEEE’s
MTTS, LEOS (now PhS), and COMSOC from 2006, and a member of OSA from 2018.
Leonid Zhukov graduated from Moscow technical university of communications and
informatics in 2019, and works at Russian Technological University MIREA 2016 as a
laboratory assistant researcher after an research engineer at the STC 'Integrated Microwave
Photonics'. He is a co-author of 1 monographs published by IntechOpen. His main research
interests are microwave-photonics, and telecommunication technologies.
Professor Dr. Alexander. S. Sigov is an expert in Solid State Physics and Electronics. He
contributed extensively to the phenomenology of magnets, ferroelectrics and multiferroics,
physics of ferroic-based heterostructures, thin films, etc. The results of his scientific
activity are reflected in more than 300 papers, reviews, book chapters, 19 monographs and
textbooks, including the well-known “Defects and Structural Phase Transitions” together
with A. Levanyuk. For many years, he has chaired the Department of Nanoelectronics in
MIREA. He created his own school, inspiring and mentoring many talented scientists. In
2006, he was elected a Member of the Russian Academy of Sciences. He is the head of the Russian
Academy Council on Dielectrics and Ferroelectrics, member of numerous scientific societies, Associate
Editor of international journals Ferroelectrics and Integrated Ferroelectrics, Editor and member of Boards
of more than ten Russian national journals, Chair of the Council on Physics and Astronomy of the Russian
Foundation for Basic Research. At present, Alexander Sigov is the Head of Nanoelectronics Dept. and
President of MIREA – Russian Technological University, Moscow, Russia, Doctor of Physics, and Fellow
member of the Russian Academy of Sciences.
Prof. Dr. Mikhail G. Vasil'ev - received an engineering degree from Moscow Institute of
Steel and Alloys, in 1969, Ph. D. degree from the same Institute in 1975, and Sc. D.
degree in quantum electronics in 1984. From 1977 to 1980, he carried out a set of works to
create new equipment and materials for semiconductor lasers, as a result of which new
technological equipment and special materials were created that determined the further
development of Russian semiconductor lasers and photodiodes. In 1984, as part of a group
of authors headed by academician Zh. Alferov, Dr. Vasil'ev awarded the State Prize of the
USSR for a series of works devoted to fundamental research of multicomponent solid solutions based on
A3B5 semiconductor compounds. These studies formed the basis for the creation of domestic devices for
quantum electronics and were actively used in a number of domestic developments. He is also active in
scientific and teaching fields working as a professor of the Peoples' Friendship University of Russia
(RUDN) and supervising graduate and PhD students. At present, Prof. Vasil'ev is working as a Head of the
Laboratory of Semiconductor and Dielectric Materials in Kurnakov Institute of General and Inorganic
Chemistry of the Russian Academy of Sciences. Over the years of scientific work, he published about 150
scientific papers and received 25 patents.

ADVANCED SERVICE DATA PROVISIONING FOR REAL-TIME MANAGEMENT OF ONGOING CELLULAR COMMUNICATION NETWORKS

More Related Content

Similar to ADVANCED SERVICE DATA PROVISIONING FOR REAL-TIME MANAGEMENT OF ONGOING CELLULAR COMMUNICATION NETWORKS (20)

More from IJCNCJournal (20)

Recently uploaded (20)

ADVANCED SERVICE DATA PROVISIONING FOR REAL-TIME MANAGEMENT OF ONGOING CELLULAR COMMUNICATION NETWORKS