ZERO100L ultrasonic level meter manual. two lines

ZERO100L
USER MANUAL
ZERO Instrument
Ultrasonic Level Meter

Receipt Acknowledgement of Warranty Card for Ultrasonic Level
Meter
User’s name
Contact address
Contact person Tel.
Product type Product No.
Date of acceptance
check
Setter
in-charge
……………………………………………………………………………………
Notes on Warranty Card for Dual Point Ultrasonic Level Meter
Product type Product No.
Date of acceptance
check
Setter
in-charge
Warranty policies：
 The user shall show the warranty card when the meter is repaired. If any fault
arises because of normal using during the warranty period, the meter will be
repaired for free by virtue of the warranty card.
 Warranty period: The warranty period of products of the company shall last
twelve months since the date of acceptance check.
Following cases are beyond the scope of free warranty:
 The product or its part is beyond the period of free warranty.
 Hardware fault caused by that the application environment does not meet the
product’s application requirements.
 Faults or damage caused by bad power supply environment or by foreign
matter’s entering the equipment.
 Faults caused by the operation that is not carried out according to application
methods and points for attention stated in the using and operation manual.
 Faults caused by natural factors and force majeure, such as thunder, flood, and
water.
Faults or damage caused by dismounting or repair without permission, by
unauthorized refit, or by abuse
Points on restriction：
 The warranty card should be properly kept by the user to be as the warranty
certificate. If lost, it won’t be reissued.
The company shall own the warranty card’s interpretation power and have the right to
amend the card’s contents without advance notice.
7
Catalogue
1 Overview ………………………………………………………………………………….1
2 Technical targets…………………………………………………………………………1
3 Installation of meter ……………………………………………………………………2
3.1 Meter’s overall size ………………………………………………………………….2
3.2 Meter’s wiring …………………………………………………………………………2
3.3 The meaning of installation parameters …………………………………………..3
3.4 Installation principles of meter………………………………………………………3
3.5 Points for attention on installation……………………………………………………4
4 Debugging of meter……………………………………………………………………4
4.1 Keyboard directive …………………………………………………………….…….4
4.2 Password directive ……………………………………………….…….………... 5
4.3 Setting of parameters ……………………………………………….…….…… 5
4.3.1 Demarcating of liquid level【P01 】 ……………………………………………5
4.3.2 Setting of 20mA【P02 】 ………………………………………………………5
4.3.3 Display mode settings【P03 】 ………………………………………………5
4.3.4 Probe height【P04 】 ………… ………………………………………………6
4.3.5 Reaction rate is set【P05 】 …… ……………………………………………6
4.3.6 Blind spot Set【P06】 ………………………………………………………….6
4.3.7 Test 4~20mA【P09 】 ………………………………………………………….6

1、Overview
Sincerely thank you for buying our ultrasonic level meter.
The meter includes several proprietary technologies, is safe and clean, with high
precision and long service life, stable and reliable, and convenient to install and
maintain, and is applicable to various fields of acid, alkali, salt, anticorrosion, and high
temperature.
The meter is with following features:
 For circuit design, high-quality power modules are selected to be as power supply
parts and highly stable and reliably imported devices are used as components of
the meter. It can fully replace imported foreign meters of the same type.
 Patent sonic-wave intelligent technology software can make intelligentized echo
analysis. It needs neither debugging nor other special steps. This technology has
functions of dynamic thinking and dynamic analysis.
 Our sonic-wave intelligent patent technology greatly improves the meter’s
precision, and the precision of liquid level is up to 0.3%, which is enough to resist
various interference waves.
 The meter is a non-contact one and does not directly contact liquid, so the fault
rate is low. The meter can be installed in several different ways, and the user can
make meter calibration according to the Manual.
 The meter’s all input and output lines must be with such protection functions as
lightning protection and short circuit prevention.
2、Technical targets
Measuring range： 0～15m（Chosen based on actual measuring range）
Blind area： 0.25m～0.6m
Ranging accuracy： 0.3%（Standard condition）
Ranging resolution： 1mm
Pressure： Less than four atmospheric pressure
Meter display： With LCD to display liquid levels.
Analog output： 4～20mA,500ohms max loop load
Power supply voltage： DC24V, lightning proof device installed inside
Ambient temperature：－20℃ ～＋60℃
Protection grade： IP67
1
Ultrasonic Level
Meter
4.3.4 Probe height（P04）
P04 menus can be displayed probe height, can see whether the height can Meet the
situation on the ground, Can also be used for Calibration of the liquid level. In
accordance with the situation on the ground to change the value of the probe height
4.3.5 Reaction rate is set（P05）
（P05）Reaction rate is set “00 ”is the fastest; “01”is faster ; “02”is medium-speed; “03”is
slow.
4.3.6 Blind spot Set（P06）
Can change the instrument’s blind spot to accommodate to complex working conditions.
For example, the protruding material impact on the instrument can be avoided near the
transducers.
4.3.7 Test 4~20mA （P09）
(P09) Test 4~20mA current.

6
【OK】：Confirmation key. Choose menu or confirm option and data.
4.2 Password directive
Press key [Mode], the password interface will appear: “0000”; press key [▲]to
change the first place into 1, and press key [OK],to enter the interface of parameter
setting menu.
4.3 parameter setting
4.3.1 Level Calibration（P01）
Finished Meter installed, power-on. The LCD will show the level value, but the data
are often inconsistent with the actual level, so it need level calibration.
Level calibration steps are as follows: press 【Mode】and enter password then
press【OK】and enter the parameter setting menu. P01 is level calibration menu, Press
OK button to P01 level calibration with (shift), and ▲ (numbers change) will be
replaced by the actual level value of the number(as 2.100), Press OK button to confirm,
then press Mode key to exit the parameter setting menu, LCD will be displayed at this
time.
4.3.2 Set 20mA（P02）
Instrument Normal working hours press Mode key to enter the parameter setting
menu, press ▲ choose menu P02, The second line corresponds to number shall be
20mA level, press OK key to set。
For example: Range is 0 ~ 10 meter ultrasonic level gauge, the actual maximum level in
the field is 6.5 meters, 6.5m can be set to 20mA, When the liquid level reaches 6.5
meters, the output current is 20mA. 20mA can also be set to 7.0 meters, then when the
level reached 7.0 meters, the output current is 20mA
4.3.3 Display mode settings（P03）
Menu P03 can change the display mode, a total of three display modes to choose
1. “00”Liquid level and relay status display
2. “01” Display space distance
3. “02”Display space distance and temperature , Press ▲ key to select the desired
mode and then press the OK button to confirm.
5
Ultrasonic Level
Meter
3、Installation of meter
3.1 Meter’s overall size
Installation way:
Open environment commonly used stent installation method, using a fixed flange
own instrument.
3.2 Meter’s wiring

2
3.3 The meaning of installation parameters
As shown, instrument’s transducers made after the wave hit the level reflected
back to transducer, the transducer receives income calculated after the hair waves to
waves of time, are measured from the L, meter installation height minus the
measurement of TH the distance L will be the current level H.
Meter range means the instrument can measure the distance, the installation
should be less than a high degree of TH range.
Instrument blind means measuring instruments in the vicinity of the transducer
can not be measured in the region, the highest level with the transducer spacing should
be greater than the blind, for example: blind spot for the 0.3m, the highest level with the
transducer spacing must be greater than 0.3m.
3.4 Instrumentation Principles
1. The distance of transducer launching surface to the lowest level should be less than
the purchase instrument range
2. The distance of the transducer launching surface to the highest liquid level should
be greater than the purchase of the blind instrument
3. The launch surface of the transducer should be keep parallel to the liquid surface.
4. Transducer installation location should be as far as possible avoid these liquid
surface fluctuations position that just under the inlet, outlet ,if It is impossible to avoid,
3
Ultrasonic Level
Meter
please install guided-wave tube to aid in measuring.
5. If the pool wall or tank wall is not smooth, meter installation location should at least
more than 0.5m from the pool wall or tank wall. The specific distance from the pool wall
or the tank wall determined according to the actual situation.
6. If the distance of the transducer launching surface to the highest level is less than
the blind area of the purchase instrument is required to install an extension tube, that
diameter is greater than 200mm, and the length is 0.35m～0.50m.
3.6 Installation Notes
1. The instrument used outdoors, it is best to install awning or the protecting housing, so
as to avoid the LCD screen ageing affected by sunlight.
2. Wire, cable protection pipes, pay attention to sealing to prevent water, and prevent
mice and other rodents Bite.
3. Although the instrument itself with a lightning protection device, but the instrument
when used in a multi-mine area, it is recommended into the outlet end of the instrument
to install lightning protection devices dedicated.
4. Instruments are used in particularly hot, cold places, which mean there is likely to
exceed the ambient temperature around the instrument's work requirements, so we
propose increase fortify high and low temperature devices around the liquid level
gauge.
4、Debugging of meter
4.1 Keyboard directive

【Mode】：Menu key. Press 【Mode】, the password surface will appear, and input
password to
enter the menu. When setting, press 【Mode】to cancel the setting; after
finishing
setting, press 【Mode】 to withdraw from the menu.
【▲】： Page down key and number key. In menu, the key is used as the page down
key of
menu; when changing data, the key is used as number key.
【】：Shift key and page up key. In menu, the key is used as the page up key of menu;
when
changing data, the key is used as shift key.
4

ZERO100L ultrasonic level meter manual. two lines

More Related Content

What's hot (17)

Similar to ZERO100L ultrasonic level meter manual. two lines (20)

More from Dalian Zero Instrument Technology Co., Ltd China (20)

Recently uploaded (20)

ZERO100L ultrasonic level meter manual. two lines