Unit4 kvv

Author: K.V. Vijayendra
Department of Civil Engineering, BIT, Bangalore.
1
GEOTECHNICAL ENGINEERING – II (Subject Code: 06CV64)
UNIT 4: FLOW NETS
4.1 Introduction
In this chapter the topics that are covered include principles of seepage analysis,
graphical solutions for seepage problems (flow nets), estimation of quantity of seepage
and exit gradient, determination of phreatic line in earth dams with and without filter,
piping effects and protective filter.
Objectives of this study are to understand basic principles of two dimensional flows
through soil media. This understanding has application in the problems involving seepage
flow through soil media and around impermeable boundaries which are frequently
encountered in the design of engineering structures.
Two dimensional flow problems may be classified into two types namely,
1. Confined flow; for example, Flow of water through confined soil stratum.
2. Unconfined flow; for example, Flow of water through body of the earth dam.
These problems are to be addressed in geotechnical engineering in order to meet the
following objectives of practical importance;
To calculate quantity of flow (seepage) – incase of both confined & unconfined flow
To obtain seepage pressure distribution and uplift pressures (stability analysis)
To verify piping tendencies leading to instability
Preliminaries required for good understanding of this topic include continuity equation,
Darcy’s law of permeability, and the validity, limitations and assumptions associated
with Darcy’s law.
Water flows from a higher energy to a lower energy and behaves according to the
principles of fluid mechanics. The sum of velocity head, pressure head and elevation
head at any point constitute total head or hydraulic head which is causing the flow.
According to Bernoulli’s energy principle, this total head responsible for flow of water is
constant in any flow regime. However in case of flow through soil medium the velocity
of flow is very small, hence contribution from velocity head is usually disregarded. The
flow of water is governed by continuity equation. The continuity equation for steady state
two dimensional flow with x and y velocity components xv and yv respectively is given
by,
0yx
vv
x y
∂∂
+ =
∂ ∂
(4.1)
According to Darcy’s law, discharge velocity of flow in a porous soil medium is
proportional to hydraulic gradient that is,v h∝ . If kx and ky are the coefficients of
permeability of soil, ix and iy are the hydraulic gradients in x and y directions respectively
and h(x, y) is the hydraulic head of flow, then
; &x x x x y y y y
h h
v k i k v k i k
x y
∂ ∂
= = = =
∂ ∂
(4.2)

2
4.2 Seepage analysis – Laplace’s equation
Laplace’s equation governs the flow of an incompressible fluid, through an
incompressible homogeneous soil medium. Combining continuity equation (Equation
4.1) and Darcy’s equations (Equation 4.2) yields,
2 2
2 2
0x y
h h
k k
x y
∂ ∂
+ =
∂ ∂
(4.3)
For the case of isotropic soil the permeability coefficient is independent of direction that
is, x yk k k= = thus Equation 4.3 becomes,
2 2
2 2
0
h h
x y
∂ ∂
+ =
∂ ∂
(4.4)
This equation is known as the Laplace's equation. The two dimensional flow of water
through soil is governed by Laplace’s equation. Laplace’s equation describes the energy
loss associated with flow through a medium. Laplace’s equation is used to solve many
kinds of flow problems, including those involving flow of heat, electricity, and seepage.
Assumptions associated with Laplace’s equation are stated below; the limitation implied
by each of these assumptions is stated within the brackets.
1. Darcy’s law is valid
(Flow is laminar)
2. The soil is completely saturated
(Degree of saturation is 100%)
3. The soil is homogeneous
(Coefficient of permeability is constant everywhere in the soil medium)
4. The soil is isotropic
(Coefficient of permeability is same in all directions)
5. During flow, the volume of soil & water remains constant
(No expansion or contraction)
6. The soil and water are incompressible
(No volume change occurs)
Laplace equation is a partial differential equation. When Laplace equation (Equation 4.4)
is solved graphically the equation gives flow net consisting two sets of curves
intersecting at right angles known as flow lines (or stream lines) and equipotential lines.
4.3 Flow nets
The solution of Laplace equation requires knowledge of the boundary conditions.
Geotechnical problems have complex boundary conditions for which it is difficult to
obtain a closed form solution. Approximate methods such as graphical methods and
numerical methods are often employed. Flow net technique is a graphical method, which
satisfies Laplace equation. A flow net is a graphical representation of a flow field
(Solution of Laplace equation) and comprises a family of flow lines and equipotential
lines (Refer to Figure 4.1)

3
4.3.1 Characteristics of flow nets
1. Flow lines or stream lines represent flow paths of particles of water
2. Flow lines and equipotential line are orthogonal to each other
3. The area between two flow lines is called a flow channel
4. The rate of flow in a flow channel is constant (∆q)
5. Flow cannot occur across flow lines
6. An equipotential line is a line joining points with the same head
7. The velocity of flow is normal to the equipotential line
8. The difference in head between two equipotential lines is called the potential
drop or head loss (∆h)
9. A flow line cannot intersect another flow line.
10. An equipotential line cannot intersect another equipotential line
Figure 4.1: Flow net and its characteristics
4.3.2 Quantity of Seepage:
As mentioned earlier the main application of flow net is that it is employed in estimating
quantity of seepage. If H is the net hydraulic head of flow, the quantity of seepage due to
flow may estimated by drawing flow net part of which is shown in Figure 4.1. The flow
net must be drawn by considering appropriate boundary conditions and adhering to
characteristics of flow nets stated earlier in paragraph 4.3.1. With reference to Figure 4.1
following terms may be defined in order to estimate quantity of seepage.
Nd = Number of equipotential drops, that is, number of squares between two adjacent
streamlines (Flow Lines) from the upstream equipotential to downstream equipotential.
Nf = Number of flow channels that is, number of squares between two adjacent
equipotential lines from one boundary streamline to the other boundary streamline
∆q = flow through one flow channel (between two adjacent streamlines)
∆h = head loss between two adjacent equipotential lines
Flow lines
(Stream lines)
Equipotential lines
a
Flow channel (∆∆∆∆q)
∆∆∆∆h = Equipotential drop
∆∆∆∆h = Equipotential drop
b= ∆∆∆∆l

4
Consider a flow grid of dimension (Figure 4.1)
Where,
dis tan ce between equipotential lines &
area across flow channel
Head loss for every potential drop : & Hydraulic gradient :
But, ,
Flow p
−
−
∴
d
d d
a×b
b= l
a = A
H h h
h= i = =
N l b
H H
h = i =
N b N
er channel(Darcy's law):
Total flow per unit width across each flow channel:
If then,
( implies that each flow grid is square)
d
f
f
d
H
q = v i = k i A= k a
b N
N a
q = q N (1)= k H
N b
a = b,
a = b,
7RWDO IORZ XQLW ZLGWK7RWDO IORZ XQLW ZLGWK7RWDO IORZ XQLW ZLGWK7RWDO IORZ XQLW ZLGWK

¡¡¡¡
1111
T N +T N +T N +T N +
1111
Thus the quantity of seepage across total width L of soil medium beneath the dam is
given by
f
d
N
Q = q× L= k H × L
N
(4.5)
Where,
Number of equipotential drops, Number of flow channels,
coefficient of permeability Net hydraulic head
= =
= =
d fN N
k H
4.3.3 Guidelines for drawing flow nets
Draw to a convenient scale the cross sections of the structure, water elevations,
and soil deposit profiles.
Establish boundary conditions that is, Identify impermeable and permeable
boundaries. The soil and impermeable boundary interfaces are flow lines. The soil
and permeable boundary interfaces are equipotential lines.
Draw one or two flow lines and equipotential lines near the boundaries. Sketch
intermediate flow lines and equipotential lines by smooth curves adhering to
right-angle intersections such that area between a pair of flow lines and a pair of
equipotential lines is approximately a curvilinear square grid.
Where flow direction is a straight line, flow lines are equal distance apart and
parallel. Also, the flownet in confined areas between parallel boundaries usually
consists of flow lines and equipotential lines that are elliptical in shape and
symmetrical

5
Try to avoid making sharp transition between straight and curved sections of flow
and equipotential lines. Transitions must be gradual and smooth. Continue
sketching until a problem develops.
Successive trials will result in a reasonably consistent flow net. In most cases, 3 to
8 flow lines are usually sufficient. Depending on the number of flow lines
selected, the number of equipotential lines will automatically be fixed by
geometry and grid layout
4.3.4 Typical illustrations of flownet
Following illustrations, Figures 4.2, Figures 4.3, Figures 4.4 and Figures 4.5 demonstrate
the typical flow nets drawn for different kinds of seepage problems pertaining to flow
beneath hydraulic structures like, dam, sheet pile, dam with sheet pile as heel cutoff wall
and dam with sheet pile as toe cutoff wall respectively.
Figure 4.2: Typical flow net for the flow beneath the dam without any cutoff wall
[Lambe R.V. Whitman (1979)]
Figure 4.3: Typical flow net for the flow around a sheet pile wall

6
Figure 4.4: Typical flow net for the flow beneath the dam with heel cutoff wall
Figure 4.5: Typical flow net for the flow beneath the dam with toe cutoff wall
4.4 Exit gradient
Hydraulic Gradient: The potential drop between two adjacent equipotential lines
divided by distance between them is known as hydraulic gradient. Thus, the hydraulic
gradient across any square in the flow net involves measuring the average dimension of
the square. The maximum value of hydraulic gradient which results in maximum seepage
velocity occurs across smallest square (flow grid).
Exit Gradient: The exit gradient is the hydraulic gradient at the downstream end of the
flow line where percolating water leaves the soil mass and emerges into the free water at
the downstream

7
4.4.1 Maximum Exit Gradient: dams and sheet pile walls
The maximum exit gradient for the cases of both dams and sheet pile walls can be
determined from the flow net. The maximum exit gradient is given by
∆
=exit
h
i
l
(4.6)
Where, ∆h is the head lost between the last two equipotential lines, and the l length of
the flow element (Refer to Figure 4.6)
Figure 4.6: Computation of maximum exit gradient
Figure 4.7: Computation of maximum exit gradient for sheet pile wall

8
4.4.2 Maximum Exit Gradient: Sheet pile walls
Maximum exit gradient Sheet pile walls can be computed alternatively as explained
below. A theoretical solution for the determination of the maximum exit gradient for a
single row of sheet pile structures is available and is of the form (Refer to Figure 4.7)
1 21 1
exit
d
Maximum hydraulic head H H
i
depth of penetration of sheet pile lπ π
−
= = (4.7)
4.4.3 Critical Hydraulic Gradient
Consider a case of water flowing under a hydraulic head x through a soil column of
height H as shown in the Figure 4.8.
Figure 4.8: Computation of critical hydraulic gradient at point O.
The state of stress at point O situated at a depth of h2 from the top of soil column may be
computed as follows,
1 2
1 2
Vertical stress at O is,
If is the unit weight of water then pore pressure at O is,
( )
Ov w sat
w O
o w
h h
u
u h h x
σ γ γ
γ
γ
= +
= + +

9
'
If and saturated and submerged unit weights of the soil column respectively,
Then effective stress at O is,
satγ γ
'
2
( 1) 1 1
1 1
w
critical
w w
Gx G
i
h e e
γγ
γ γ
− −
= = = × =
+ +
Where G is the specific gravity of the soil particles and e is the void ratio of the soil mass.
Therefore critical hydraulic gradient corresponds to hydraulic gradient which tends to a
state of zero effective stress. Hence critical hydraulic gradient is given by
1
1
critical
G
i
e
−
=
+
(4.8)
4.5 Piping Effects
Soils can be eroded by flowing water. Erosion can occur underground, beneath the
hydraulic structures, if there are cavities, cracks in rock, or high exit gradient induced
instability at toe of the dam, such that soil particles can be washed into them and
transported away by high velocity seeping water. This type of underground erosion
progresses and creates an open path for flow of water; it is called “piping”. Preventing
piping is a prime consideration in the design of safe dams. Briefly the processes
associated with initiation of piping in dams are as follows,
Upward seepage at the toe of the dam on the downstream side causes local
instability of soil in that region leading erosion.
A process of gradual erosion and undermining of the dam may begin, this type
of failure known as piping, has been a common cause for the total failure of
earth dams
The initiation of piping starts when exit hydraulic gradient of upward flow is
close to critical hydraulic gradient
Factor of safety against piping is defined as,
critical
exit
i
FS
i
= (4.9)
Where iexit is the maximum exit gradient and icritical is the critical hydraulic gradient
(Equation 4.8). The maximum exit gradient can be determined from the flow net. A factor
of safety of 3 to 4 is considered adequate for the safe performance of the structure against piping
failure.
'
1 2 1 2
' '
2 2
'
' '
2
( ) ( )
( )
For quick sand condition(sand boiling) the effective stress tends to zero;
that is, 0
We get critical hydraulic gradient as,
Ov o w sat w
sat w w w
critical
w
u h h h h x
h x h x
i
h x
σ σ γ γ γ
σ γ γ γ γ γ
σ
σ γ γ
= − = + − + +
= − − = −
=
= − = 0;

10
4.6 Design of Filters
In order to avoid failures of hydraulic structures due to piping effects, many remedial
measures are available. Some of these remedial measures that are usually adopted in
practice are shown in Figure 4.9. They include providing impervious blanket on the
upstream and gravel filter at the toe as shown for the case of an earth dam (Figure 4.9).
Main objectives of these measures are preventing buildup of high seepage pressure and
migration of eroded soil particles.
Figure 4.9: Remedial measures against piping
When seepage water flows from a soil with relatively fine grains into a coarser material
there is a danger that the fine soil particles may wash away into the coarse material. Over
a period of time, this process may clog the void spaces in the coarser material. Such a
situation can be prevented by the use of a protective filter between the two soils.
Conditions for the proper selection of the filter material are,
1. The size of the voids in the filter material should be small enough to hold the
larger particles of the protected material in place.
2. The filter material should have a high permeability to prevent buildup of large
seepage forces and hydrostatic pressures in the filters.
The experimental investigation of protective filters provided the following criteria which
are to be followed to satisfy the above conditions:
Creteria-1
¢¤£¦¥¨§©¢¤£¦¥¨§©¢¤£¦¥¨§©¢¤£¦¥¨§©
£¦¥ ©£¦¥ ©£¦¥ ©£¦¥ ©
''''
ื W R ื W R ื W R ื W R
''''
------------- To satisfy condition 1
Creteria-2
¢¤£¦¥¨§©¢¤£¦¥¨§©¢¤£¦¥¨§©¢¤£¦¥¨§©
¢¤£¦¥ ©¢¤£¦¥ ©¢¤£¦¥ ©¢¤£¦¥ ©
''''
ุ W R ุ W R ุ W R ุ W R
''''
------------- To satisfy condition 2
Where,
D15 (F)
= diameter through which 15% of filter material will pass
D15(S)
= diameter through which 15% of soil to be protected will pass
D85(S)
= diameter through which 85% of soil to be protected will pass

11
4.7 Seepage Flow through Homogeneous Earth Dams
In order to draw flow net to find quantity of seepage through the body of the earth dam it
is essential to locate top line of seepage. This upper boundary is a free water surface and
will be referred to as the line of seepage or phreatic line. The seepage line may therefore
be defined as the line above which there is no hydrostatic pressure and below which there
is hydrostatic pressure. Therefore phreatic line is the top flow line which separates
saturated and unsaturated zones within the body of the earth dam.
Therefore the problem of computation of the seepage loss through an earth dam primarily
involves prediction of the position of the line of seepage in the cross-section.
4.7.1 Locating Phreatic Line
It has been noticed from experiments on homogeneous earth dam models that the line of
seepage assumes more or less the shape of a parabola. Also, assuming that hydraulic
gradient i is equal to the slope of the free surface and is constant with depth (Dupit’s
theory), the resulting solution of the phreatic surface is parabola. In some sections a little
divergence from a regular parabola is required particularly at the surfaces of entry and
discharge of the line of seepage. The properties of the regular parabola which are
essential to obtain phreatic line are depicted in Figure 4.10.
Figure 4.10: geometrical properties of regular parabola
Every point on the
parabola is equidistant
from focus and directrix
Therefore,
FA AB====
Also,
S
FG GE p
2
= = == = == = == = =
Focus = (0,0)
Any point, A on the
parabola is given by,
(((( ))))A A x, z====
(((( ))))
22 2
2 2
x z 2p x
that is,
z 4p
x
4p
+ = ++ = ++ = ++ = +
−−−−
====

12
4.7.2 Phreatic line for an earth dam without toe filter
In the case of a homogeneous earth dam resting on an impervious foundation with no
drainage filter, the top flow line ends at some point on the downstream face of the dam;
the focus of the base parabola in this case happens to be the downstream toe of the dam
itself as shown in Figure 4.11.
Figure 4.11: Phreatic line for an earth dam without toe filter
The following are the steps in the graphical determination of the top flow line for a
homogeneous dam resting on an impervious foundation without filters:
1. Draw the earth dam section and upstream water level (H) to some convenient
scale. Let Point-2 is the point on the upstream face coinciding with water level.
2. Let ∆∆∆∆ be the horizontal distance between point- 2 and upstream heel of the dam.
Locate Point-1 at a distance of 0.3 times ∆∆∆∆ from Point-2 on the water surface.
That is distance 1- 2 is 0.3∆∆∆∆
3. Focus of the base parabola is located at the downstream toe of the dam, that is
Point-0 (distance 0 - 1 is d). Select x-z reference axis with focus 0 as origin.
4. directrix of the parabola is at distance 2p from the focus 0, where p is given by,
( )2 21
p = d + H - d
2
5. By choosing suitable values of z-ordinates (for example; 0.2H, 0.4H … H)
compute the x-ordinates of the base parabola using the relation,
2 2
z - 4p
x =
4p
.
6. Join all these points to get base parabola starting from Point-1 and concluding at a
point midway between focus-0 and directrix. This parabola will be correct for the
central portion of the top flow line. Necessary corrections at the entry on the
upstream side and at exist on the downstream side are to be made.
7. Upstream correction: The portion of the top flow line at entry is sketched visually
to meet the boundary condition there that is phreatic line meets perpendicularly

13
with the upstream face, which is a boundary equipotential and the phreatic line is
made to meet the base parabola tangentially at a convenient point.
8. Downstream correction (Casagrande’s method): The breakout point on the
downstream discharge face may be determined by measuring out L from the toe
along the face. If ββββ is the downstream slope angle then L may be may be
computed from the following equations,
2 2
0
2 2
0 0 2 2 2 2 2
d d H
For 30 , L = - - ;
cos cos sin
For 30 90 , L = H + d - d - H cot
9. Finally the quantity of seepage flow through may be compute from the following
equations,
0
0 0 2
For 30 , q = kL sin tan
For 30 90 , q = kL sin
Where, k is the coefficient of permeability of the dam material.
4.7.3 Phreatic line for an earth dam with toe filter
The following are the steps in the graphical determination of the top flow line for a
homogeneous dam with a toe filter: [Refer to Figures 4.12 (a), (b), (c), (d), (e)]
1. Draw the earth dam section and upstream water level (H) to some convenient
scale.
2. Locate Point-B, the point on the upstream slope coinciding with water level.
3. Let ∆∆∆∆ be the horizontal distance between point- B and upstream heel of the dam.
Locate Point-A at a distance of 0.3 times ∆∆∆∆ from Point-B on the water surface.
That is distance AB is 0.3∆∆∆∆ [Refer to Figure 4.12(a)]
4. Select F as the focus of the parabolic phreatic line, Point-F is located at the
intersection of the bottom flow line and the downstream toe filter. Let horizontal
distance between points A F be d i.e., AF = d
5. Locate Point-G on the directrix of the parabola, located a distance 2P from the
focal point, Point-F, that is FG = 2P where, [Refer to Figure 4.12(b)]
( )2 21
p = d + H - d
2
6. Select base of the dam and directrix as X Z axes

14
Figure 4.12(a)
Figure 4.12(b)
Figure 4.12(c)
Figure 4.12(d)
Figure 4.12(e)
Figure 4.12: Phreatic line for an earth dam with toe filter

15
7. By choosing suitable values of z-ordinates (for example; 0.2H, 0.4H … H)
compute the x-ordinates of the base parabola using the relation,
2 2
z - 4p
x =
4p
.
Thus 1 2 3 4z , z , z , z ...... are computed for the ordinates
1 2 3 4x , x , x , x ......respectively [Refer to Figure 4.12(c)].
8. Join all such located points to get basic parabola. This parabola meets toe filter
(equipotential line) orthogonally at midpoint of FG that is at a distance p from F
(vertex K of the parabola). Joint points K-0-1-2-3-4-A to get parabola ABK
[Refer to Figure 4.12(d)].
9. Apply modification to phreatic line at the entry Point-B on the upstream slope
which is an equipotential line. Draw line perpendicular to upstream slope starting
from B and meets the base parabola smoothly and tangentially at a convenient
point say, C. Complete the phreatic line BCK (top flow line) by joining BC erase
remaining portion of the base parabola [Refer to Figure 4.12(e)].
10. Finally the quantity of seepage flow through may be compute from the following
equations,
Let the distance between is
i.e., the distance between focus and directrix, 2
Then the quantity of seepage through unit length of dam is,
F G S
S p∴ = ×
× ×q = kS = k (2 p) = 2kp
Where, k is the coefficient of permeability of the dam material.
4.8 Problems
Problem 4.1: (July/August – 2002)
For a homogeneous earth dam of 52 m height and 2 m free board, the flownet has 22
potential drops and 5 flow channels. Calculate the discharge per meter length of the dam,
given k = 22 X 10-6 m/sec
Solution: Problem 4.1
-6
d f
f -6
d
Data given :
H = 52 - 2= 50 m, N = 22, N = 5, k = 22×10 m / sec
Solution :
N 5
Q = k×H× = 22×10 ×50×
N 22
3
-4 m
Q = 2.5×10 (Answer)
s× m

16
Problem: 4.2
A concrete dam (Refer to figure P-4.1) 17.5 m base retains water to a level of 11.0 m on
the upstream. The water level on the downstream is 2.0 m. the impervious stratum is 10.0
m below the dam. The coefficient of permeability k = 10-6 m/sec. If dam is 50 m long
Compute total quantity of seepage flow per day below the dam. Also compute seepage
pressure at point P, 5 m below the center of the dam.
Figure: P-4.1
Figure P-4.2
Draw the dam section to scale also locate point-P at which seepage pressure is
required as shown in Figure P-4.2 (water levels need not be drawn to scale).
Identify that AB EF are equipotential lines and BC, CD, DE GH are flow lines
Sketch flow lines and equipotential lines according to guidelines stated earlier
(Section: 4.3.3). Draw two flow lines perpendicular to boundary equipotential lines
and parallel to boundary flow lines identified in the previous step.

17
Complete the flow net by drawing sufficient number of equipotential lines such that
they are perpendicular to flow lines and approximately square flow elements are
formed. In this case nine such equipotential lines are drawn in order to satisfy these
conditions as shown in Figure 4.3.
Thus three flow channels and ten equipotential lines are formed as illustrated in
Figure P-4.3. Therefore 3 10f dN N= = .
Head drop for every equipotential drop is
d
H 9.0
h= = = 0.90
N 10
Seepage loss under the dam:
Therefore total discharge is,

ง 4 ™ ™ ™ ™ P GDง 4 ™ ™ ™ ™ P GDง 4 ™ ™ ™ ™ P GDง 4 ™ ™ ™ ™ P GD
Figure P-4.3
Seepage pressure at P: In the Figure P-4.3 identify that location of point P is coinciding
with fifth equipotential line, i.e., there are 5 equipotential drops till point P. seepage
pressure at this location can be computed by using any arbitrary datum. For illustration
purpose seepage pressure at P is computed for two different datum yielding same results.
6
6
11 2 9.0 1 10 /
Therefore the discharge due to seepage is
3
10 9 per meter length
10
f
d
Head H m k m s
N
q k H
N
−
= = − = = ×
= ⋅ ⋅ = × × =

PPPP
™ ™ ™ ™
VVVV

18
( )
Total head at is,
( ) 9.0 (5)
9
( ) 9.0 5 4.5
10
Elevation head, ( ) 9.0
Seepage pressure head,
( ) ( ) ( )
( ) 4.5 ( 9.0) 13.5
Pore pressure at ,
( ) 13.
Case-1:
Datum is top of tail water
t P
t P
z P
s P t P z P
s P
P s P w
P
h h
h m
h m
h h h
h m
P
u h γ
= − ∆
= − =
= −
= −
= − − =
= × =
2
5 9.81
132.435 /Pu kN m
×
=
( )
Total head at is,
( ) 21.0 (5)
9
( ) 21.0 5 16.5
10
Elevation head,( ) 3.0
( ) ( ) ( )
( ) 16.5 ( 3.0) 13.5
Pore pressure at ,
(
Case- 2 :
Datum is top of impervious layer
t P
t P
z P
s P t P z P
s P
P s
P
h h
h m
h m
h h h
h m
P
u h
= − ∆
= − =
= +
= −
= − + =
=
2
) 13.5 9.81
132.435 /
P w
Pu kN m
γ× = ×
=
Thus it can be concluded that seepage pressure can be computed considering any
arbitrary datum to get same results. Hence seepage pressure head at P is, s P(h ) = 13.5 m
which yields the pore pressure at P as, 2
Pu = 132.435 kN / m (kPa) .
Problem: 4.3 (July – 2007)
A soil stratum with permeability, k = 5 X 10-7 cm/sec overlies an impermeable stratum.
The impermeable stratum lies at a depth of 18 m below the ground surface. A sheet pile
wall penetrates 8 m into the permeable soil stratum. Water stands to a height of 9 m on
upstream side and 1.5 m on down stream side, above the surface of soil stratum. Sketch
the flownet and determine:
a. Quantity of seepage
b. The seepage pressure at a point P located 8 m below surface of soil stratum and 4
m away from the sheet pile wall on its upstream side
c. The pore water pressure at point P and
d. The maximum exit gradient
Draw the dam section to scale also locate point-P at which seepage pressure is
required as shown in Figure P-4.2 (water levels need not be drawn to scale). Identify
the boundary conditions, i.e., boundary lines that represent equipotential lines and
flow lines as shown in Figure 4.3.
Sketch flow lines and equipotential lines according to guidelines stated earlier
(Section: 4.3.3). Draw three flow lines perpendicular to boundary equipotential lines
and parallel to boundary flow lines identified in the previous step.

19
Complete the flow net by drawing sufficient number of equipotential lines such that
they are perpendicular to flow lines and approximately square flow elements are
formed. In this case seven such equipotential lines are drawn in order to satisfy these
conditions as shown in Figure 4.5.
Thus four flow channels and eight equipotential lines are formed as illustrated in
Figure P-4.5. Therefore 4 8f dN N= = . Number of equipotential drops at the
location of Point-P is 2.5 (P is located midway between 2nd
and 3rd
equipotential
lines) i.e., d P(N ) = 2.5 .
Head drop for every equipotential drop is
7.5
h= = 0.9375
8
Figure P-4.4
Figure P-4.5

20
Seepage loss under the sheet pile
7 9
9
Data: Head,
Coeff. of permeability, 5 10 / 5 10 /
Therefore seepage loss is,
4
5 10 7.5
8
f
d
H = 9.0 -1.5=7.5 m,
k = cm s m s
N
Q k H
N
− −
−
× = ×
= ⋅ ⋅ = × × ×
3
-8
-8 -3 3
m
Q = 1.875×10
s - m
Q = 1.875×10 × 3600× 24 = 1.62×10 m / day / m
Seepage pressure Pore pressure at P: In the Figure P-4.5 identify that location of point
P is midway between 2nd
and 3rd
equipotential lines, i.e., there are 2.5 equipotential drops
till point P. seepage pressure at this location can be computed by using any arbitrary
datum. For illustration purpose seepage pressure at P is computed for two different datum
yielding same results.
( )
Total head at is,
( ) 7.5 (2.5)
7.5
( ) 7.5 2.5 5.15625
8
Elevation head, ( ) 9.50
( ) ( ) ( )
( ) 5.15625 ( 9.50) 14.65625
Pore pressure
Case-1:
Datum is top of tail water
t P
t P
z P
s P t P z P
s P
P
h h
h m
h m
h h h
h m
= − ∆
= − =
= −
= −
= − − =
at ,
( ) 14.65625 9.81P s P w
P
u h γ= × = ×
2
Pu = 143.7778 kN / m
( )
Total head at is,
( ) 27.0 (2.5)
7.5
( ) 27.0 2.5 24.65625
8
Elevation head,( ) 10.0
( ) ( ) ( )
( ) 24.65625 ( 10.0) 14.65625
Por
Case- 2 :
Datum is top of impervious layer
t P
t P
z P
s P t P z P
s P
P
h h
h m
h m
h h h
h m
= − ∆
= − =
= +
= −
= − + =
e pressure at ,
( ) 14.65625 9.81P s P w
P
u h γ= × = ×
2
Pu = 143.7778 kN / m
Thus it can be concluded that seepage pressure can be computed considering any
arbitrary datum to get same results. Hence seepage pressure head at P is,
s P(h ) = 14.656 m which yields the pore pressure at P as, 2
Pu = 143.778 kN / m (kPa)
Maximum exit gradient:
Maximum exit gradient for flow beneath the sheet pile wall may be computed using any
of the two methods explained 4.4.1 and 4.4.2. Herein both of these methods are employed
to compute maximum exit gradient. In case of first method dimension of the last flow

21
element is used (Figure P-4.6), while in the second method depth of penetration of sheet
pile is used to compute maximum exit gradient.
Figure P-4.6
Method – 1*
The head lost between the last two equipotential lines ∆h , and the l length of the last flow
element adjacent to sheet pile is used to compute the exit gradient. The length l of the last
element, as shown in Figure P-4.6, is equal to 3.1 m. Therefore, using equation 4.6, we
get
1 2 9.0 1.5
8
0.9375
3.1
Maximum exit gradient = 0.3024
d
exit
H H
h
N
h
i
l
− −
∆ = = =
∆
= = =

Method – 2*
The maximum exit gradient for a single row of sheet pile structures is computed using
depth of embedment of sheet pile, ld. For the present case, ld = 8 m. Therefore, using
equation 4.7, we get
1 21 1 9.0 1.5
8
Maximum exit gradient = 0.2984
exit
d
H H
i
lπ π
− −
= = =
*
Note: The maximum exit gradient computed using two methods closely agrees with a
difference of about 1.32 % in the result.

22
Problem: 4.4 (Jan/Feb-2004)
An earth dam has the following details: Top width 10 m., upstream and downstream
slopes 2.5 horizontal to 1 vertical. Total height of dam 35 m., the height of water stored
30 m. downstream filter 60 m. long. K for dam material 3.75x10-3
mm/sec. Draw the
phreatic line and calculate the discharge through the dam.
For the present problem, the solution is obtained by referring to the general diagram of
phreatic line of the dam shown in Figure P-4.7
Figure P-4.7
Referring to Figure P-4.7 and to the procedure described in section 4.7.3, the data given
in the present problem are interpreted to obtain solution as follows,
Top width of the dam Height of the dam
Height of water Downstream filter length
Upstream and downstream slope angles
Base
-1 o
= ML=10 m, = 35 m,
= BE = 30 m, = FJ =60.0 m
1
= = = tan = 21.80
2.5
[[[[ ]]]](((( ))))width of the dam
With respect to origin F, coordinates of point
∴ ∆ ×∴ ∆ ×∴ ∆ ×∴ ∆ ×
1 1
= DJ = ML+ 35× + = 10+ 35× 5.0 = 185.0 m
tan( ) tan( )
1
DE = = BE× = 30×2.5 =75.0 m, AB = 0.3 = 0.3 75= 22.5 m
tan( )
A(x, z)= A(d,H)
(((( )))) (((( ))))
are,
(F is the focus of the base parabola)
∴∴∴∴
∴∴∴∴
2 2 2 2
x= d = DJ -(FJ + DE)+ AB = 185.0 -(60.0+75.0)+22.5
x= d =72.5 m z = H = 30.0 m, A(x,z)=(72.5,30.0)
S FG 1 1
p = = ; p = d +H - d = 72.5 +30 -72.5
2 2 2 2
p = 2.981 m S = 2× p = 2×2.981
Seepage loss through the dam is,
= 5.962 m
q= k×S

23
Where, coefficient of permeability
∴∴∴∴
-3
-6 -5 3
k = 3.75×10 mm / sec
q= 3.75×10 ×5.962= 2.23575×10 m / sec
-5 3
q = 2.23575 ×10 × 3600× 24 = 1.932 m / day / meter length of dam
Note: After point-A (starting point of base parabola) and directrix passing through point-
G are fixed select x-z reference axes with F as origin of the base parabola. Obtain the
coordinates (x, z) of various points describing the base parabola using the value of p in
the relation,
2 2
z - 4p
x =
4p
. Join all points to get base parabola and draw phreatic line by
applying appropriate correction on upstream face at point-B as shown in Figure P-4.7.
The procedure is described in Section 4.7.3. This is left to the student as an exercise.
Problem: 4.5
An earth dam section is shown in Figure P-4.8 Determine the rate of seepage through the
earth dam Assume that k = 10−5
m/min.
Figure: P-4.8
The given problem is concerned with seepage through dam without downstream filter.
The general diagram of phreatic line of seepage flow is shown in Figure P-4.9. The detail
procedure for plotting this phreatic line is described in Section 4.7.2.
Figure: P-4.9

24
Referring to Figure: P-4.9, following calculations are carried out using the procedure of
Section 4.7.2.
Top width of the dam Height of the dam Height of water
Upstream and downstream slope angles
Base width of the dam
-1 o
=7.0 m, = 35 m, = 32 m
1
= = = tan = 26.565
2.0
1 1
=7.0+ 35× +
tan( ) tan( )
[[[[ ]]]](((( ))))
With respect to origin, are, (Origin is focus of the base parabola)
'
' '
'
∴ ×∴ ×∴ ×∴ ×
=7+ 35× 2+2 = 147.0 m
1
= 32× = 32×2= 64.0 m, aa = 0.3 = 0.3 64 = 19.2 m
tan( )
a (x, z)= a (d,H)
x= d = 147.0 - +aa = 147.0 -64.0+19.2=
Using Casagrande's method ( we have,
Seepage loss
'
∴∴∴∴ 0
2 2 2 2
2 2 2 2
102.2 m z = H = 32.0 m,
a (x,z)=(102.2,32.0), For 30 ),
d d H 102.2 102.2 32
L = bc= - - = - - = 25.18 m
cos cos sin cos26.565 cos 26.565 sin 26.565
0
For 30 , through the dam is,
Where, coefficient of permeability
∴ ×∴ ×∴ ×∴ ×
-5
-5 -5 3
k =10 m / min
q=1×10 ×25.18 26.565 26.565 = 5.63×10 m / min
-5 3
q = kL sin tan
sin tan
q = 2.23575×10 ×60× 24 = 0.0811 m / day / meter length of dam
Reference:
• Braja M. Das, “Advanced Soil Mechanics”, Third edition, 2007, Taylor Francis
• Lambe T.W. R.V. Whitman, “Soil Mechanics”, SI Version, 1979, John Wiley
Sons
• B.C. Punmia, “Soil Mechanics and Foundations”, Thirteenth Edition, 1994,
Laxmi Publications (P) Ltd.
• V. N. S. Murthy, “Geotechnical Engineering: Principles and Practices of Soil
Mechanics and Foundation Engineering”, Marcel Dekker, Inc.,

Unit4 kvv

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Unit4 kvv (20)

More from Pavan Kumar N (14)

Unit4 kvv