Vlt hvac basic_quick_start_guide_fc101

MAKING MODERN LIVING POSSIBLE
QQuick Guide
VLT® HVAC Basic Drive
www.danfoss.com/drives
*MG18A302*
132R0078 MG18A302 Rev. 2011-09-20

Contents
1 Quick Guide 2
1.1 Safety 2
1.1.1 Warnings 2
1.1.2 Safety Instructions 2
1.2 Introduction 3
1.2.1 Available Literature 3
1.2.2 Approvals 3
1.2.3 IT Mains 3
1.2.4 Avoid Unintended Start 3
1.2.5 Disposal Instruction 4
1.3 Installation 4
1.3.1 Before Starting Repair Work 4
1.3.2 Side-by-Side Installation 4
1.3.3 Dimensions 5
1.3.4 Electrical Installation in General 6
1.3.5 Connecting to Mains and Motor 8
1.3.6 Fuses 14
1.3.7 EMC-Correct Electrical Installation 16
1.3.8 Control Terminals 18
1.3.9 Electrical Overview 19
1.4 Programming 20
1.4.1 Programming with the Local Control Panel (LCP) 20
1.4.3 The Start-up Wizard for Open Loop Applications 21
1.5 Parameter Overview 28
1.6 Warnings and Alarms 33
1.7 General Specifications 35
1.7.1 Mains Supply 3 x 200-240 V AC 35
1.7.5 EMC Test Results 41
1.8 Special Conditions 44
1.8.1 Derating for Ambient Temperature and Switching Frequency 44
1.8.2 Derating for Low Air Pressure 44
1.9 Options for VLT HVAC Basic Drive FC101 44
Contents VLT HVAC Basic Drive Quick Guide
MG18A302 - VLT® is a registered Danfoss trademark 1

1 Quick Guide
1.1 Safety
1.1.1 Warnings
WARNING
High Voltage Warning
The voltage of the frequency converter is dangerous
whenever it is connected to mains. Incorrect installation of
the motor or frequency converter may cause damage to
the equipment, serious injury or death. Consequently, it is
essential to comply with the instructions in this manual as
well as local and national rules and safety regulations.
WARNING
Electrical Hazard
Touching the electrical parts may be fatal - even after the
equipment has been disconnected from mains. Also make
sure that other voltage inputs have been disconnected
(linkage of DC intermediate circuit). Be aware that there
may be high voltage on the DC link even when the LEDs
are turned off. Before touching any potentially live parts of
the frequency converter, wait at least as stated in the table
below:
Voltage (V) Power range (kW) Min. waiting time
(minutes)
3 x 200 0.25 – 3.7 4
3 x 200 5.5 – 11 15
3 x 400 0.37 – 7.5 4
3 x 400 11 – 90 15
3 x 600 2.2 – 7.5 4
3 x 600 11 – 90 15
CAUTION
Leakage Current:
The earth leakage current from the frequency converter
exceeds 3.5 mA. According to IEC 61800-5-1 a reinforced
Protective Earth connection must be ensured by means of
a min. 10 mm² Cu or an additional PE wire - with the same
cable cross section as the Mains wiring - must be
terminated separately.
Residual Current Device:
This product can cause a DC current in the protective
conductor. Where a residual current device (RCD) is used
for extra protection, only an RCD of Type B (time delayed)
shall be used on the supply side of this product. See also
Danfoss Application Note on RCD, MN90GXYY.
Protective earthing of the frequency converter and the use
of RCDs must always follow national and local regulations.
Motor thermal protection:
Motor overload protection is possible by setting Parameter
1-90 Motor thermal protection to the value Electronic
Thermal Relay (ETR) trip.
WARNING
Installation at high altitudes
For altitudes above 2 km, please contact Danfoss regarding
PELV.
1.1.2 Safety Instructions
• Make sure the frequency converter is properly
connected to earth.
• Do not remove mains connections, motor
connections or other power connections while
the frequency converter is connected to power.
• Protect users against supply voltage.
• Protect the motor against overloading according
to national and local regulations.
• The earth leakage current exceeds 3.5 mA.
• The [OFF] key is not a safety switch. It does not
disconnect the frequency converter from mains.
Quick Guide VLT HVAC Basic Drive Quick Guide
2 MG18A302 - VLT® is a registered Danfoss trademark
11

1.2 Introduction
1.2.1 Available Literature
This quick guide contains the basic information necessary
for installing and running the frequency converter. If more
information is needed, literature can be found on the
enclosed cd or downloaded from:
http://www.danfoss.com/Products/Literature/Technical
+Documentation.htm
1.2.2 Approvals
1.2.3 IT Mains
CAUTION
IT Mains
Installation on isolated mains source, i.e. IT mains.
Max. supply voltage allowed when connected to mains:
440 V (3 x 380-480 V units).
On IP20 200-240 V 0.25-11 kW and 380-480 V IP20 0.37-22
kW, open the RFI switch by removing the screw on the
side of the frequency converter when at IT grid.
130BB612.10
1
Illustration 1.1 IP20 200-240 V 0.25-11 kW, IP20 0.37-22 kW
380-480 V.
1: EMC screw
130BC251.10
Illustration 1.2 IP54 400 V 0.75-18.5 kW
1: EMC screw
On all units, set par. 14-50 RFI filter to OFF when operating
in IT mains.
CAUTION
If reinserted, only use M3 x 12 screw.
1.2.4 Avoid Unintended Start
While the frequency converter is connected to mains, the
motor can be started/stopped using digital commands, bus
commands, references or via the LCP.
• Disconnect the frequency converter from mains
whenever personal safety considerations make it
necessary to avoid unintended start of any
motors.
• To avoid unintended start, always activate the
[OFF] key before changing parameters.
1 1

1.2.5 Disposal Instruction
Equipment containing electrical components
must not be disposed of together with domestic
waste.
It must be separately collected with electrical
and electronic waste according to local and
currently valid legislation.
1.3 Installation
1.3.1 Before Starting Repair Work
1. Disconnect FC101 from mains (and external DC
supply, if present.)
2. Wait as stated in the table below for discharge of
the DC-link:
Voltage (V) Power range (kW) Min. waiting time
(minutes)
3 x 200 0.25 – 3.7 4
3 x 200 5.5 – 45 15
3 x 400 0.37 – 7.5 4
3 x 400 11 – 90 15
3 x 600 2.2 – 7.5 4
3 x 600 11 – 90 15
3. Remove motor cable
1.3.2 Side-by-Side Installation
The frequency converter can be mounted side-by-side and requires the clearance above and below for cooling.
Power Clearance above/
below (mm/inch)
Frame IP class 3 x 200-240 V 3 x 380-480 V 3 x 525-600 V
H1 IP20 0.25-1.5 kW/0.33-2 Hp 0.37-1.5 kW/0.5-2 Hp 100/4
H2 IP20 2.2 kW/3 Hp 2.2-4 kW/3-5.4 Hp 100/4
H3 IP20 3.7 kW/5 Hp 5.5-7.5 kW/7.5-10 Hp 100/4
H4 IP20 5.5-7.5 kW/7.5-10 Hp 11-15 kW/15-20 Hp 100/4
H5 IP20 11 kW/15 Hp 18.5-22 kW/25-30 Hp 100/4
H6 IP20 15-18.5 Kw/20-25 Hp 30-45 kW/40-60 Hp 22-30 kW/30-40 Hp 200/7.9
H7 IP20 22-30 kW/30-40 Hp 55-75 kW/100-120 Hp 45-55ø W/60-100 Hp 200/7.9
H8 IP20 37-45 kW/50-60 Hp 90 kW/125 Hp 75-90 kW/120-125 Hp 225/8.9
H9 IP20 2.2-7.5 kW/3-10 Hp 100/4
H10 IP20 11-15 kW/15-20 Hp 200/7.9
NOTE
With IP21/Nema Type1 option kit mounted, a distance of 50 mm between the units is required.
11

1.3.3 Dimensions
A
a
b
B
C
0 D
130BB614.10
e
fa
d
e
130BC205.10
e
fa
e
130BC246.10
Enclosure Power [kW] Height [mm] Width [mm] Depth
[mm]
Mounting hole [mm] Max.W
eight
Frame IP Class 3 x
200-240 V
3 x
380-480 V
3 x
525-60
0 V
A "A incl
Decoupling
Plate"
a B b C d e f Kg
H1 IP20 0.25-1.5
kW
0.37-1.5
kW
195 273 183 75 56 168 9 4.5 5.3 2.1
H2 IP20 2.2 kW 2.2-4.0 kW 227 303 212 90 65 190 11 5.5 7.4 3.4
H3 IP20 3.7 kW 5.5-7.5 kW 255 329 240 100 74 206 11 5.5 8.1 4.5
H4 IP20 5.5-7.5 kW 11-15 kW 296 359 275 135 105 241 12.6 7 8.4 7.9
H5 IP20 11 kW 18.5-22
kW
334 402 314 150 120 255 12.6 7 8.5 9.5
H6 IP20 15-18.5
kW
30-45 kW 22-30
kW
518 595/635(45
kW)
495 239 200 242 - 8.5 15 24.5
H7 IP20 22-30kW 55-75 kW 45-55
kW
550 630/690(75
kW)
521 313 270 335 - 8.5 17 36
H8 IP20 37-45kW 90 kW 75-90
kW
660 800 631 375 330 335 - 8.5 17 51
H9 IP20 2.2-7.5
kW
269 374 257 130 110 205 11 5.5 9 6.6
H10 IP20 11-15
kW
399 419 380 165 140 248 12 6.8 7.5 12
I2 IP54 0.75-4.0
kW
332 - 318.5 115 74 225 11 5.5 9 5.3
I3 IP54 5.5-7.5 kW 368 - 354 135 89 237 12 6.5 9.5 7.2
I5 IP54 11-18.5
kW
480 - 454 242 210 260 19 9 9 23
I6 IP54 22-37 kW 650 - 624 242 210 260 19 9 9 27
I7 IP54 45-55 kW 680 - 648 308 272 310 19 9 9.8 45
I8 IP54 75-90 kW 770 - 739 370 334 335 19 9 9.8 65
The dimensions are only for the physical units, but when installing in an application it is necessary to add space for free air
passage both above and below the units. The amount of space for free air passage is listed in Table 1.1:
1 1

Enclosure Clearance needed for free air passage [mm]
Frame IP class Above unit Below unit
H1 20 100 100
H2 20 100 100
H3 20 100 100
H4 20 100 100
H5 20 100 100
H6 20 200 200
H7 20 200 200
H8 20 225 225
H9 20 100 100
H10 20 200 200
I2 54 100 100
I3 54 100 100
I5 54 200 200
I6 54 200 200
I7 54 200 200
I8 54 225 225
Table 1.1 Clearance needed for free air passage [mm]
1.3.4 Electrical Installation in General
All cabling must comply with national and local regulations on cable cross-sections and ambient temperature. Copper
conductors required, (75°C) recommended.
Power (kW) Torque (Nm)
Frame IP class 3 x 200-240 V 3 x 380-480 V Line Motor DC
connection
Control
terminals
Earth Relay
H1 IP20 0.25-1.5 0.37-1.5 1.4 0.8 0.8 0.5 0.8 0.5
H2 IP20 2.2 2.2-4 1.4 0.8 0.8 0.5 0.8 0.5
H3 IP20 3.7 5.5-7.5 1.4 0.8 0.8 0.5 0.8 0.5
H4 IP20 5.5-7.5 11-15 1.2 1.2 1.2 0.5 0.8 0.5
H5 IP20 11 18.5-22 1.2 1.2 1.2 0.5 0.8 0.5
H6 IP20 15-18 30-45 4.5 4.5 - 0.5 3 0.5
H7 IP20 22-30 55 10 10 - 0.5 3 0.5
H7 IP20 - 75 14 14 - 0.5 3 0.5
H8 IP20 37-45 90 242 242 - 0.5 3 0.5
Frame IP class 3 x 380-480 V Line Motor DC connection Control
terminals
Earth Relay
I2 IP54 0.75-4.0 1.4 0.8 0.8 0.5 0.8 0.5
I3 IP54 5.5-7.5 1.4 0.8 0.8 0.5 0.8 0.5
I5 IP54 11-18.5 1.8 1.8 - 0.5 3 0.6
I6 IP54 22-37 4.5 4.5 - 0.5 3 0.6
I7 IP54 45-55 10 10 - 0.5 3 0.6
I8 IP54 75-90 14/241 14/241 - 0.5 3 0.6
11

Frame IP class 3 x 525-600 V Line Motor DC connection Control
terminals
Earth Relay
H9 IP20 2.2-7.5 1.8 1.8 not
recommended
0.5 3 0.6
H10 IP20 11-15 1.8 1.8 not
recommended
0.5 3 0.6
H6 IP20 22-30 4.5 4.5 - 0.5 3 0.5
H7 IP20 45-55 10 10 - 0.5 3 0.5
H8 IP20 75-90 14/241 14/241 - 0.5 3 0.5
Table 1.2 Details of Tightening Torques
1 Cable dimensions ≤ 95 mm2
2 Cable dimensions > 95 mm2
1 1

1.3.5 Connecting to Mains and Motor
The frequency converter is designed to operate all
standard three-phased asynchronous motors. For
maximum cross-section on wires please see section
1.7 General Specifications.
• Use a shielded/armored motor cable to comply
with EMC emission specifications, and connect
this cable to both the decoupling plate and the
motor metal.
• Keep motor cable as short as possible to reduce
the noise level and leakage currents.
• For further details on mounting of the
decoupling plate, please see instruction
MI02QXYY
• Also see EMC-Correct Installation in the Design
Guide, MG18CXYY.
1. Mount the earth wires to earth terminal.
2. Connect motor to terminals U, V and W.
3. Mount mains supply to terminals L1, L2 and L3
and tighten.
H1-H5 Frame
IP20 200-240 V 0.25-11 kW and IP20 380-480 V 0.37-22 kW.
130BB634.10
1
2
2
3
4
Motor
U V W -DC+DC
MAINS
1 Line
2 Earth
3 Motor
4 Relays
11

H6 Frame
IP20 380-480 V 30-45 kW
IP20 200-240 V 15-18.5 kW
IP20 525-600 V 22-30 kW
1
95
99
L1 91 / L2 92 / L3 93
U 96 / V 97 / W 98
030201
060504
2 3 4
130BB762.10
1 Line
2 Motor
3 Earth
4 Relays
H7 Frame
IP20 380-480 V 55-75 kW
IP20 200-240 V 22- 30 kW
IP20 525-600 V 45-55 kW
1 2
3
4
130BB763.10
1 Line
2 Relays
3 Earth
4 Motor
1 1

H8 Frame
IP20 380-480 V 90 kW
IP20 200-240 V 37-45 kW
IP20 525-600 V 75-90 kW
130BB764.10
1
2
3
4
98
97
96
99
95
93
92
91
L1 L1
L1
U
V w
1 Line
2 Relays
3 Earth
4 Motor
H9 Frame
IP20 600 V 2.2-7.5 kW
-DC+DC
BR- BR+
U
V
W
99
M
A
I N
S
95
RELAY1RELAY2
-LC+
130BA261.10
130BA262.10
M
I
N
S
+DC
BR-
BR+
U
V
W
RELAY1RELAY2
95
11

130BA263.10
95
M
A
I
N
S
+DC
BR- BR+
U
V
W
91
92 93
L1
L2
L3
RELAY1RELAY2
+DC
BR- BR+
U
V
W
M
A
I
N
S
L1 L2
L391 92
93
RELAY1RELAY2
99
-LC-
130BA264.10
MOTOR
MOTOR
U V W
99
130BT302.12
H10 Frame
IP20 600 V 11-15 kW
130BA725.10
1 1

I2 Frame
IP54 380-480 V 0.75-4.0 kW
130BC299.10
7
3
2
5
1
8
4
6
1 RS 485
2 Line in
3 Earth
4 Wire clamps
5 Motor
6 UDC
7 Relays
8 I/O
I3 Frame
IP54 380-480 V 5.5-7.5 kW
130BC201.10
1 RS 485
2 Line in
3 Earth
4 Wire clamps
5 Motor
6 UDC
7 Relays
8 I/O
11

IP54 I2-I3 frame
130BC203.10
I6 Frame
IP54 380-480 V 22-37 kW
130BT326.10130BT325.10
1 1

311
130BA215.10
RELAY 1
RELAY 2
9
9
6
030201
900504
I7, I8 Frame
IP54 380-480 V 45-55 kW
IP54 380-480 V 75-90 kW
91
L1
92
L2
93
L3
96
U
97
V
98
W
88
DC-
89
DC+
81
R-
8
R+
9995
130BA248.10
1.3.6 Fuses
Branch circuit protection
In order to protect the installation against electrical and
fire hazard, all branch circuits in an installation, switch
gear, machines etc., must be short-circuit and overcurrent
protected according to national/international regulations.
Short circuit protection
Danfoss recommends using the fuses mentioned in the
following tables to protect service personnel or other
equipment in case of an internal failure in the unit or
short-circuit on DC-link. The frequency converter provides
full short circuit protection in case of a short-circuit on the
motor.
Overcurrent protection
Provide overload protection to avoid overheating of the
cables in the installation. Overcurrent protection must
always be carried out according to national regulations.
Fuses must be designed for protection in a circuit capable
of supplying a maximum of 100,000 Arms (symmetrical),
480 V maximum.
Non UL compliance
If UL/cUL is not to be complied with, Danfoss recommends
using the fuses mentioned in Table 1.3, which will ensure
compliance with IEC 61800-5-1:
In case of malfunction, not following the fuse recommen-
dation may result in damage to the frequency converter.
11

Circuit Breaker Fuse
UL Non UL UL Non UL
Bussman
n
Bussman
n
Bussman
n
Bussman
n
Max fuse
Power kW Type RK5 Type RK1 Type J Type T Type G
3 x 200 - 240 V
IP20
0.25 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
0.37 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
0.75 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
1.5 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
2.2 FRS-R-15 KTN-R15 JKS-15 JIN-15 16
3.7 FRS-R-25 KTN-R25 JKS-25 JIN-25 25
5.5 FRS-R-50 KTN-R50 JKS-50 JIN-50 50
7.5 FRS-R-50 KTN-R50 JKS-50 JIN-50 50
11 FRS-R-80 KTN-R80 JKS-80 JIN-80 65
15 Cutler-Hammer
EGE3100FFG
Moeller NZMB1-A125
FRS-R-100 KTN-R100 125
18.5 FRS-R-100 KTN-R100 125
22 Cutler-Hammer
JGE3150FFG
Moeller NZMB1-A160
FRS-R-150 KTN-R150 160
30 FRS-R-150 KTN-R150 160
37 Cutler-Hammer
JGE3200FFG
Moeller NZMB1-A200
FRS-R-200 KTN-R200 200
45 FRS-R-200 KTN-R200 200
3 x 380 - 480 V
IP20
0.37 FRS-R-10 KTS-R10 JKS-10 JJS-10 10
0.75 FRS-R-10 KTS-R10 JKS-10 JJS-10 10
1.5 FRS-R-10 KTS-R10 JKS-10 JJS-10 10
2.2 FRS-R-15 KTS-R15 JKS-15 JJS-15 16
3 FRS-R-15 KTS-R15 JKS-15 JJS-15 16
4 FRS-R-15 KTS-R15 JKS-15 JJS-15 16
5.5 FRS-R-25 KTS-R25 JKS-25 JJS-25 25
7.5 FRS-R-25 KTS-R25 JKS-25 JJS-25 25
11 FRS-R-50 KTS-R50 JKS-50 JJS-50 50
15 FRS-R-50 KTS-R50 JKS-50 JJS-50 50
18.5 FRS-R-80 KTS-R80 JKS-80 JJS-80 65
22 FRS-R-80 KTS-R80 JKS-80 JJS-80 65
30
Cutler-Hammer
EGE3125FFG
Moeller NZMB1-A125
FRS-R-80 KTS-R80 JKS-R80 JJS-R80 80
37 FRS-R-100 KTS-R100 JKS-R100 JJS-R100 100
55 Cutler-Hammer
JGE3200FFG
Moeller NZMB1-A200
FRS-R-150 KTS-R150 JKS-R150 JJS-R150 150
90
Cutler-Hammer
JGE3250FFG
Moeller NZMB2-A250 FRS-R-250 KTS-R250 JKS-R250 JJS-R250 250
1 1

Circuit Breaker Fuse
UL Non UL UL Non UL
Bussman
n
Bussman
n
Bussman
n
Bussman
n
Max fuse
Power kW Type RK5 Type RK1 Type J Type T Type G
3 x 525 - 600 V
IP20
2.2 KTS-R20 20
3 KTS-R20 20
5.5 KTS-R20 20
7.5 KTS-R20 30
11 KTS-R30 35
15 KTS-R30 35
22 Cutler-Hammer
EGE3080FFG
Cutler-Hammer
EGE3080FFG
FRS-R-80 KTN-R80 80
30 FRS-R-80 KTN-R80 80
45 Cutler-Hammer
JGE3125FFG
Cutler-Hammer
JGE3125FFG
FRS-R-125 KTN-R125 125
55 FRS-R-125 KTN-R125 125
75 Cutler-Hammer
JGE3200FAG
Cutler-Hammer
JGE3200FAG
FRS-R-200 KTN-R200 200
90 FRS-R-200 KTN-R200 200
3 x 380 - 480 V
IP54
0.75
1.5
2.2
3
4
5.5
7.5
11
15
18.5
22
Moeller NZMB1-A125
125
30 125
37 125
45
Moeller NZMB2-A160
160
55 160
75
Moeller NZMB2-A250
200
90 200
Table 1.3 Fuses
1.3.7 EMC-Correct Electrical Installation
General points to be observed to ensure EMC-correct
electrical installation.
• Use only screened/armoured motor cables and
screened/armoured control cables.
• Connect the screen to earth at both ends.
• Avoid installation with twisted screen ends
(pigtails), since this ruins the screening effect at
high frequencies. Use the cable clamps provide-
dinstead.
• It is important to ensure good electrical contact
from the installation plate through the installation
screws to the metal cabinet of the frequency
converter.
• Use starwashers and galvanically conductive
installation plates.
• Do not use unscreened/unarmoured motor cables
in the installation cabinets.
11

L1
L2
L3
PE
Min. 16 mm2
Equalizing cable
Control cables
All cable entries in
one side of panel
Earthing rail
Cable insula-
tion stripped
Output con-
tactor etc.
Motor cable
Motor, 3 phases and
PLC etc. Panel
Mains-supply
Min. 200mm
between control
cable, mains cable
and between mains
motor cable
PLC
Protective earth
Reinforced protective earth
130BB761.10
Illustration 1.3 EMC-correct Electrical Installation
For North America use metal conduits instead of shielded cables.
1 1

1.3.8 Control Terminals
IP20 200-240 V 0.25-11 kW and IP20 380-480 V 0.37-22 kW:
130BB622.10
Illustration 1.4 Location of Control Terminals
1. Place a screwdriver behind the terminal cover to
activate snap.
2. Tilt the screwdriver outwards to open the cover.
IP20 380-480V 30-90kW.
130BB624.10
1. Place a screwdriver behind the terminal cover to
activate snap.
2. Tilt the screwdriver outwards to open the cover.
Digital input 18, 19 and 27 mode is set in 5-00 Digital Input
Mode (PNP is default value) and digital input 29 mode is
set in 5-03 Digital Input 29 Mode (PNP is default value).
IP54 400 V 0.75-7.5 kW
130BC249.10
1. Remove the front cover.
Control terminals:
Illustration 1.5 shows all control terminals of the frequency
converter. Applying Start (term. 18), connection between
terminal 12-27 and an analog reference (term. 53 or 54
and 55) make the frequency converter run.
18 19
12 20 55
27 29 42 45 50 53 54
DIGIIN
DIGIIN
DIGIIN
DIGIIN
61 68 69
N
P
COMM.GND
+24V
0/4-20mA A OUT / DIG OUT 0/4-20mA A OUT / DIG OUT
GND
GND
10V/20mAIN
10V/20mAIN
10VOUT
130BB625.10
BUS TER.
OFF ON
Illustration 1.5 Control Terminals
11

1.3.9 Electrical Overview
L1
L2
L3
3 Phase
power
input
PE PE
+10Vdc
0-10Vdc-
0-10Vdc-
50 (+10V OUT)
54 (A IN)
53 (A IN)
55 (COM A IN/OUT)
0/4-20 mA
0/4-20 mA
42 0/4-20mA A OUT / DIG OUT
45 0/4-20mA A OUT / DIG OUT
18 (DIGI IN)
19 (DIGI IN)
27 (DIGI IN)
29 (DIGI IN)
12 (+24V OUT)
24V (NPN)
20 (COM D IN)
OV (PNP)
24V (NPN)
OV (PNP)
24V (NPN)
OV (PNP)
24V (NPN)
OV (PNP)
Bus ter.
Bus ter.
RS-485
Interface
RS-485(N PS-485) 69
(P RS-485) 68
(Com RS-485 ) 61
(PNP)-Source
(NPN)-Sink
ON=Terminated
OFF=Unterminated
ON
12
240V AC 3A
Not present on all power sizes
Do not connect shield to
61 on 116,117 and 118 unites
01
02
03
relay1
relay2
UDC+
UDC-
Motor
U
V
W
130BB626.10
06
05
04
240V AC 3A
NOTE
Please note there is no access to UDC- and UDC+ on the following units:
IP20 380-480 V 30-90 kW
IP20 200-240 V 15-45 kW
IP20 525-600 V 2.2-90 kW
IP54 380-480 V 22-90 kW
1 1

1.4 Programming
1.4.1 Programming with the Local Control
Panel (LCP)
NOTE
The frequency converter can also be programmed from a
PC via RS485 com-port by installing the MCT-10 Set-up
Software. This software can either be ordered using code
number 130B1000 or downloaded from the Danfoss Web
site: www.danfoss.com/BusinessAreas/DrivesSolutions/
softwaredownload
1.4.2 Local Control Panel (LCP)
The following instructions are valid for the FC101 LCP. The
LCP is divided into four functional sections.
A. Alphanumeric display
B. Menu key
C. Navigation keys and indicator lights (LEDs)
D. Operation keys and indicator lights (LEDs)
Back
Com
1-20 Motor Power
[2] 0.12kW-0.16HP
Setup 1
A
B
1
12
13 14 15
11
11
10
9
8
7
6
5
4
3
2
C
D
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Oﬀ
Reset
Auto
On
Alarm
Warn
On
130BB765.10
A. Alpha Numeric Display
The LCD-display is back-lit with 2 alpha-numeric lines. All
data is displayed on the LCP.
A number of information can be read from the display.
1 Parameter number and name.
2 Parameter value.
3 Set-up number shows the active set-up and the edit set-
up. If the same set-up acts as both active and edit set-up,
only that set-up number is shown (factory setting). When
active and edit set-up differ, both numbers are shown in
the display (Setup 12). The number flashing, indicates the
edit set-up.
4 Motor direction is shown to the bottom left of the display
– indicated by a small arrow pointing either clockwise or
counterclockwise.
5 The triangle indicates if the LCP is in status, quick menu or
main menu.
B. Menu Key
Use the menu key to select between status, quick menu or
main menu.
C. Navigation keys and indicator lights (LEDs)
6 Com led: Flashes when bus communication is communi-
cating.
7 Green LED/On: Control section is working.
8 Yellow LED/Warn.: Indicates a warning.
9 Flashing Red LED/Alarm: Indicates an alarm.
10 [Back]: For moving to the previous step or layer in the
navigation structure
11 Arrows [▲] [▼]: For maneuvering between parameter groups,
parameters and within parameters. Can also be used for
setting local reference.
12 [OK]: For selecting a parameter and for accepting changes to
parameter settings
D. Operation keys and indicator lights (LEDs)
13 [Hand On]: Starts the motor and enables control of the
frequency converter via the LCP.
NOTE
Please note that terminal 27 Digital Input
(5-12 Terminal 27 Digital Input) has coast inverse as
default setting. This means that [Hand On] will not
start the motor if there is no 24 V to terminal 27, so
please connect terminal 12 to terminal 27.
14 [Off/Reset]: Stops the motor (off). If in alarm mode the
alarm will be reset.
15 [Auto On]: frequency converter is controlled either via
control terminals or serial communication.
11

At power-up
At the first power-up the user is asked to choose preferred
language. Once selected this screen will never be shown
again in the following powerups, but language can still be
changed in 0-01 Language.
130BB628.10
Select Language
[ 0 ] English
Setup 1
1.4.3 The Start-up Wizard for Open Loop
Applications
The built in “wizard” menu guides the installer through the
setup of the drive in a clear and structured manner in
order to setup an open loop application. An open loop
application is here an application with a start signal,
analog reference (voltage or current) and optionally also
relay signals (but no feed back signal from the process
applied).
FC
+24V
DIG IN
DIG IN
DIG IN
DIG IN
COM DIG IN
A OUT / D OUT
A OUT / D OUT
18
19
27
29
42
55
50
53
54
20
12
01
02
03
04
05
06
R2R1
+
-
0-10V
Start
+10V
A IN
A IN
COM
130BB674.10
45
Reference
The wizard will initially be shown after power up until any
parameter has been changed. The wizard can always be
accessed again through the quick menu. Press [OK] to start
the wizard. If [BACK] is pressed, the FC101 will return to
the status screen.
130BB629.10
Press OK to start Wizard
Push Back to skip it
Setup 1
1 1

Setup 1
Setup 1 Setup 1 Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
[0] International
Set Motor Power
1.10 kW
Set Motor Voltage
50 V
Set Motor Frequency
50 Hz
Set Motor Current
4.66 A
Set Motor Nominal Speed
1420 RPM
Set Motor Speed Low Limit
0 Hz
Set Motor Speed High Limit
65 Hz
Set Ramp 1 Ramp Up Time
0003 s
Set Ramp 1 Ramp Down Time
0003 s
Active Flying start?
[0] Disable
Select Terminal 53 Mode
[0] Voltage
Set Terminal 53 Low Voltage
0.07 V
Set Terminal 53 High Voltage
10 V
Set Terminal 53 Low Current
4 mA
Set Terminal 53 High Current
20 mA
AMA Failed
0.0 Hz
0.0 kW
Wizard completed
Press OK to accept
Automatic Motor Adaption (AMA)
[1] Enable
Auto Motor Tuning OK
Press OK
Select Function Relay 2
[0] Drive running
Select Function of Relay 1
[0] Alarm
Set Maximum Reference
0050 Hz
Set Minimum Reference
0016 Hz
AMA running
-----
OK
OK
Back
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Off
Reset
Auto
On
Alarm
Warn
On
AMA failed
Do AMA
Status Screen
The Wizard can always be
reentered via the Quick Menu!
(Do not AMA)
Current Voltage
Power Up Screen
At power up the user is
asked to choose the
prefered laguage.
Select language
[1] English
0.0 Hz
0.0 kW
Setup 1
Setup 1
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Off
Reset
Auto
On
Alarm
Warn
On
Press OK to start Wizard
Press Back to skip it
Setup 1
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Off
Reset
Auto
On
Alarm
Warn
On
The next screen will be
the Wizard screen.
Wizard Screen
AMA OK
5
7
8
9
10
11
1
2
if
if
3
17
18
19
20
21
22
25
26
27
28
29
30
31
3435
36
32 33
23
24
130BC244.10
BackBackBack
Select Regional Settings
- the HVAC FC 101 Wizard starts
Setup 1
200-240V/50Hz/Delta
Grid Type
4
Asynchronous Motor
11

The FC101 Start-up Wizard for Open Loop Applications
No & Name Range Default Function
0-03 Regional Settings [0] International
[1] US
0
0-06 Grid Type [0] 200-240 V/50 Hz/IT-grid
[1] 200-240 V/50 Hz/Delta
[2] 200-240 V/50 Hz
[10] 380-440 V/50 Hz/IT-grid
[11] 380-440 V/50 Hz/Delta
[12] 380-440 V/50 Hz
[20] 440-480 V/50 Hz/IT-grid
[21] 440-480 V/50 Hz/Delta
[22] 440-480 V/50 Hz
[30] 525-600 V/50 Hz/IT-grid
[31] 525-600 V/50 Hz/Delta
[32] 525-600 V/50 Hz
[100] 200-240 V/60 Hz/IT-grid
[101] 200-240 V/60 Hz/Delta
[102] 200-240 V/60 Hz
[110] 380-440 V/60 Hz/IT-grid
[111] 380-440 V/60 Hz/Delta
[112] 380-440 V/60 Hz
[120] 440-480 V/60 Hz/IT-grid
[121] 440-480 V/60 Hz/Delta
[122] 440-480 V/60 Hz
[130] 525-600 V/60 Hz/IT-grid
[131] 525-600 V/60 Hz/Delta
[132] 525-600 V/60 Hz
Size related Select operating mode for restart upon
reconnection of the drive to mains voltage after
power down
1-20 Motor Power 0.12-110 kW/0.16-150 hp Size related Enter motor power from nameplate data
1-22 Motor Voltage 50.0 - 1000.0 V Size related Enter motor voltage from nameplate data
1-23 Motor Frequency 20.0 - 400.0 Hz Size related Enter motor frequency from nameplate data
1-24 Motor Current 0.01 - 10000.00 A Size related Enter motor current from nameplate data
1-25 Motor Nominal
Speed
100.0 - 9999.0 RPM Size related Enter motor nominal speed from nameplate data
4-12 Motor Speed Low
Limit [Hz]
0.0 - 400 Hz 0 Hz Enter the minimum limit for low speed
4-14 Motor Speed High
Limit [Hz]
0.0 - 400 Hz 65 Hz Enter the maximum limit for high speed
3-41 Ramp 1 Ramp up
Time
0.05 - 3600.0 s Size related Ramp up time from 0 to rated 1-23 Motor
Frequency
3-42 Ramp 1 Ramp
Down Time
0.05 - 3600.0 s Size related Ramp down time from rated 1-23 Motor Frequency
to 0
1-73 Flying Start [0] Disabled
[1] Enabled
0 Select Enable to enable the frequency converter to
catch a spinning motor i.e. fan applications
6-19 Terminal 53 mode [0] Current
[1] Voltage
1 Select if terminal 53 is used for current- or voltage
input
6-10 Terminal 53 Low
Voltage
0-10 V 0.07 V Enter the voltage that corresponds to the low
reference value
6-11 Terminal 53 High
Voltage
0-10 V 10 V Enter the voltage that corresponds to the high
reference value
6-12 Terminal 53 Low
Current
0-20 mA 4 Enter the current that corresponds to the low
reference value
6-13 Terminal 53 High
Current
0-20 mA 20 Enter the current that corresponds to the high
reference value
3-02 Minimum Reference -4999-4999 0 The minimum reference is the lowest value
obtainable by summing all references
1 1

3-03 Maximum Reference -4999-4999 50 The maximum reference is the lowest obtainable
by summing all references
5-40 Function Relay [0]
Function relay
See 5-40 Function Relay Alarm Select the function to control output relay 1
5-40 Function Relay [1]
Function relay
See 5-40 Function Relay Drive running Select the function to control output relay 2
1-29 Automatic Motor
Adaption (AMA)
See 1-29 Automatic Motor Adaption
(AMA)
Off Performing an AMA optimizes motor performance
11

Closed Loop Set-up Wizard
6-29 Terminal 54 Mode
[1] Voltage mode
6-25 Terminal 54 High Ref./Feedb. Value
0050 Hz
20-94 PI Integral Time
9999 s
Current Voltage
This dialog is forced to be set to
[2] Analog in 54
24
25
26
27
28
29
30
31
20-00 Feedback1 source
[2] Analog in 54
3-10 Preset reference [0]
[1] 0
3-03 Max Reference
[1] 50
3-02 Min Reference
[1] 0
Asynchronous Motor
1-73 Flying Start
[0] No
1-22 Motor Voltage
50 V
1-24 Motor current
4.66 A
1-25 Motor nominal speed
1420 RPM
3-41 Ramp 1 ramp-up time
0003 s
3-42 Ramp1 ramp-down time
0003 s
3
4
5
6
7
13
14
15
17
18
18a
20
21
22
23
32
33
34
35
36
37
0-06 Grid Type
[200-240 V/50 Hz]
4-12 Motor speed low limit
0 Hz
4-14 Motor speed high limit
65 Hz
130BC245.10
1-20 Motor Power
1.10 kW
1-23 Motor frequency
50 Hz
6-22 Terminal 54 Low Current
4 mA
6-24 Terminal 54 Low Ref./Feedb. Value
0016 Hz
6-23 Terminal 54 High Current
20 mA
6-25 Terminal 54 High Ref./Feedb. Value
50
0,01 s
20-81 PI Normal/Inverse Control
[0] Normal
20-83 PI Start Speed
0 Hz
20-93 PI Proportional Gain
0,01 s
1-29 Automatic Motor Adaption
[1] Enable
6-20 Terminal 54 Low Voltage
0,07 V
6-24 Terminal 54 Low Ref./Feedb. Value
0 Hz
6-21 Terminal 54 High Voltage
10 V
6-26Terminal 54 Filter time constant
3-10 Preset reference is the set-point
Please note that Terminal 27 Digital Input (par. 5-12)
has coast inverse as default setting. This means that
AMA can not be performed if there is no 24V to terminal
27 so please connect terminal 12 to terminal 27.
0-01 Conﬁguration Mode
[0] Open Loop2
0-03 Regional Settings
[0] International1
3-16 Reference 2 Source
[0] No function
20
1 1

Closed Loop Set-up Wizard
0-03 Regional Settings [0] International
[1] US
0
0-06 Grid Type [0]-[[132] please see
start-up wizard for open
loop application
Size selected Select operating mode for restart upon reconnection of the
frequency converter to mains voltage after power down
1-20 Motor power 0.09-110 kW Size related Enter motor power from nameplate data
1-22 Motor Voltage 50.0 - 1000.0 V Size related Enter motor voltage from nameplate data
1-23 Motor Frequency 20.0 - 400.0 Hz Size related Enter motor frequency from nameplate data
1-24 Motor Current 0.01 - 10000.00 A Size related Enter motor current from nameplate data
1-25 Motor Nominal Speed 100.0 - 9999.0 RPM Size related Enter motor nominal speed from nameplate data
4-12 Motor Speed Low Limit
[Hz]
0.0 - 400 Hz 0.0 Hz Enter the minimum limit for low speed
4-14 Motor Speed High Limit
[Hz]
0.1 - 400 Hz 65Hz Enter the maximum limit for high speed
3-41 Ramp 1 Ramp up Time 0.05 - 3600.0 s Size related Ramp up time from 0 to rated motor frequency parameter 1-23
3-42 Ramp 1 Ramp Down
Time
0.05 - 3600.0 s Size related Ramp down time from rated motor frequency parameter 1-23 to
0
1-73 Flying Start [0] Disabled
[1] Enabled
0 Select Enable to enable the drive to catch a spinning motor
3-02 Minimum Reference -4999-4999 0 The minimum reference is the lowest value obtainable by
summing all references
3-03 Maximum Reference -4999-4999 50 The maximum reference is the highest value obtainable by
summing all references
3-10 Preset Reference -100-100% 0 Enter the set point
6-29 Terminal 54 mode [0] Current
[1] Voltage
1 Select if terminal 54 is used for current- or voltage input
6-20 Terminal 54 Low Voltage 0-10 V 0.07V Enter the voltage that corresponds to the low reference value
6-21 Terminal 54 High Voltage 0-10 V 10V Enter the voltage that corresponds to the low high reference
value
6-22 Terminal 54 Low Current 0-20 mA 4 Enter the current that corresponds to the high reference value
6-23 Terminal 54 High Current 0-20 mA 20 Enter the current that corresponds to the high reference value
6-24 Terminal 54 Low Ref./
Feedb. Value
-4999-4999 0 Enter the feedback value that corresponds to the voltage or
current set in parameter 6-20/6-22
6-25 Terminal 54 High Ref./
Feedb. Value
-4999-4999 50 Enter the feedback value that corresponds to the voltage or
current set in parameter 6-21/6-23
6-26 Terminal 54 Filter Time
Constant
0-10 s 0.01 Enter the filter time comstant
20-81 PI Normal/Inverse
control
[0] Normal
[1] Inverse
0 Select Normal [0] to set the process control to increase the
output speed when the process error is positive. Select Inverse
[1] to reduce the output speed.
20-83 PI Start Speed 0-200 Hz 0 Enter the motor speed to be attained as a start signal for
commencement of PI control
20-93 PI Proportional Gain 0-10 0.01 Enter the process controller proportional gain. Quick control is
obtained at high amplification. However if amplification os too
great, the process may become unstable
20-94 PI Integral Time 0.1-999.0 s 999.0 s Enter the process controller integral time. Obtain quick control
through a short integral time, though if the integral time is too
short, the process becomes unstable. An excessively long integral
time disables the integral action.
1-29 Automatic Motor
Adaption (AMA)
Off Performing an AMA optimizes motor performance
11

Motor Set-up
The Quick Menu Motor Set-up guides through the needed
motor parameters.
0-03 Regional
Settings
[0] Interna-
tional
[1] US
0
0-06 Grid
Type
[0]-[132] please
see start-up
wizard for
open loop
application
Size selected Select operating
mode for restart
upon
reconnection of
the frequency
converter to
mains voltage
after power
down
1-20 Motor
power
0.12-110 kW/
0.16-150 Hp
Size related Enter motor
power from
nameplate data
1-22 Motor
Voltage
50.0 - 1000.0 V Size related Enter motor
voltage from
nameplate data
1-23 Motor
Frequency
20.0 - 400.0 Hz Size related Enter motor
frequency from
nameplate data
1-24 Motor
Current
0.01 - 10000.00
A
current from
nameplate data
1-25 Motor
Nominal
Speed
100.0 - 9999.0
RPM
nominal speed
from nameplate
data
4-12 Motor
Speed Low
Limit [Hz]
0.0 - 400 Hz 0.0 Hz Enter the
minimum limit
for low speed
4-14 Motor
Speed High
Limit [Hz]
0-400 Hz 65 Enter the
maximum limit
for high speed
3-41 Ramp 1
Ramp up Time
0.05 - 3600.0 s Size related Ramp up time
from 0 to rated
motor frequency
1-23 Motor
Frequency
3-42 Ramp 1
Ramp Down
Time
0.05 - 3600.0 s Size related Ramp down time
from rated motor
frequency
1-23 Motor
Frequency to 0
1-73 Flying
Start
[0] Disabled
[1] Enabled
0 Select Enable to
enable the
frequency
converter to
catch a spinning
motor
Changes Made
Changes Made lists all parameters changed since factory
setting. Only the changed parameters in current edit-setup
are listed in changes made.
If the parameters value is changed back to factory setting's
value from another different value, the parameter will NOT
be listed in Changes Made.
1. Press [Menu] key to enter the Quick Menu until
indicator in display is placed above Quick Menu.
2. Press [▲] [▼] to select either FC101 wizard, closed
loop setup, motor setup or changes made, then
press [OK].
3. Press [▲] [▼] to browse through the parameters
in the Quick Menu.
4. Press [OK] to select a parameter.
5. Press [▲] [▼] to change the value of a parameter
setting.
6. Press [OK] to accept the change.
7. Press either [Back] twice to enter “Status”, or
press [Menu] once to enter “Main Menu”.
The Main Menu accesses all parameters.
1. Press [Menu] key until indicator in display is
placed above “Main Menu”.
2. Use [▲] [▼] to browse through the parameter
groups.
3. Press [OK] to select a parameter group.
4. Use [▲] [▼] to browse through the parameters in
the specific group.
5. Press [OK] to select the parameter.
6. Use [▲] [▼] to set/change the parameter value.
1 1

1.5 Parameter Overview
Parameter Overview
0-** Operation / Display
0-0* Basic Settings
0-01 Language
*[0] English
[1] Deutsch
[2] Francais
[3] Dansk
[4] Espanol
[5] Italiano
[28] Portuguese
[255] No Text
0-03 Regional Settings
*[0] International
[1] US
0-04 Operating State at Power-
up
*[0] Resume
[1] Forced stop, ref=old
0-06 GridType
0] 200-240 V/50 Hz/IT-grid
[1] 200-240 V/50 Hz/Delta
[2] 200-240 V/50 Hz
[10] 380-440 V/50 Hz/IT-grid
[11] 380-440 V/50 Hz/Delta
[12] 380-440 V/50 Hz
[20] 440-480 V/50 Hz/IT-grid
[21] 440-480 V/50 Hz/Delta
[22] 440-480 V/50 Hz
[30] 525-600 V/50 Hz/IT-grid
[31] 525-600 V/50 Hz/Delta
[32] 525-600 V/50 Hz
[100] 200-240 V/60 Hz/IT-grid
[101] 200-240 V/60 Hz/Delta
[102] 200-240 V/60 Hz
[110] 380-440 V/60 Hz/IT-grid
[111] 380-440 V/60 Hz/Delta
[112] 380-440 V/60 Hz
[120] 440-480 V/60 Hz/IT-grid
[121] 440-480 V/60 Hz/Delta
[122] 440-480 V/60 Hz
[130] 525-600 V/60 Hz/IT-grid
[131] 525-600 V/60 Hz/Delta
[132] 525-600 V/60 Hz
0-07 Auto DC Braking IT
[0] Off
*[1] On
0-1* Set-up Operations
0-10 Active Set-up
*[1] Set-up 1
[2] Set-up 2
[9] Multi Set-up
0-11 Programming Set-up
[1] Set-up 1
[2] Set-up 2
*[9] Active Set-up
0-12 Link Setups
[0] Not linked
*[20] Linked
0-3* LCP Readout
0-30 Custom Readout Unit
[0] None
*[1] %
[5] PPM
[10] 1/Min
[11] RPM
[12] Pulse/s
[20] l/s
[21] l/min
[22] l/h
[23] m3/s
[24] m3/min
[25] m3/h
[30] kg/s
[31] kg/min
[32] kg/h
[33] t/min
[34] t/h
[40] m/s
[41] m/min
[45] m
[60] Degree Celsius
[70] mbar
[71] bar
[72] Pa
[73] kPa
[74] m Wg
[80] kW
[120] GPM
[121] gal/s
[122] gal/min
[123] gal/h
[124] CFM
[127] ft3/h
[140] ft/s
[141] ft/min
[160] Degree Fahr
[170] psi
[171] lb/in2
[172] in WG
[173] ft WG
[180] HP
0-31 Custom Readout Min Value
0.00 - 1,000,000.0, * 0.00
0-32 Custom Readout Max Value
0.00 - 1,000,000.0, * 100.00
0-37 Display Text 1
0-38 Display Text 2
0-39 Display Text 3
0-4* LCP Keypad
0-40 [Hand on] Key on LCP
[0] Disabled
*[1] Enabled
0-42 [Auto on] Key on LCP
[0] Disabled
*[1] Enabled
0-44 [Off / Reset] Key on LCP
[0] Disable All
*[1] Enable All
[7] Enable Reset Only
0-5* Copy/Save
0-50 LCP Copy
*[0] No copy
[1] All to LCP
[2] All from LCP
[3] Size indep. from LCP
0-51 Set-up Copy
*[0] No copy
[1] Copy from setup 1
[2] Copy from setup 2
[9] Copy from Factory setup
0-6* Password
0-60 Main Menu Password
0 - 999, * 0
1-** Load and Motor
1-0* General Settings
1-00 Configuration Mode
*[0] Open loop
[3] Closed loop
1-01 Motor Control Principle
[0] U/f
*[1] VVC+
1-03 Torque Characteristics
*[1] Variable torque
[3] Auto Energy Optim.
1-06 Clockwise Direction
*[0] Normal
[1] Inverse
1-20 Motor Power
[2] 0.12 kW - 0.16 Hp
[3] 0.18 kW - 0.25 Hp
[4] 0.25 kW - 0.33 Hp
[5] 0.37 kW - 0.50 Hp
[6] 0.55 kW - 0.75 Hp
[7] 0.75 kW - 1.00 Hp
[8] 1.10 kW - 1.50 Hp
[9] 1.50 kW - 2.00 Hp
[10] 2.20 kW - 3.00 Hp
[11] 3.00 kW - 4.00 Hp
[12] 3.70 kW - 5.00 Hp
[13] 4.00 kW - 5.40 Hp
[14] 5.50 kW - 7.50 Hp
[15] 7.50 kW - 10.0 Hp
[16] 11.00 kW - 15.00 Hp
[17] 15.00 kW - 20 Hp
[18] 18.5 kW - 25 Hp
[19] 22 kW - 30 Hp
[20] 30 kW - 40 Hp
[21] 37 kW-50 Hp
[22] 45 kW-60 Hp
[23] 55 kW-75 Hp
[24] 75 kW-100 Hp
[25] 90 kW-120 Hp
[26] 110 kW-150 Hp
1-22 Motor Voltage
50 - 1000 V
1-23 Motor Frequency
20 - 400, *(50) Hz
1-24 Motor Current
0.01 - (26.00), [A]
1-25 Motor Nominal Speed
100 rpm - 6000 rpm,
1-29 Automatic Motor Adaption
(AMA)
*[0] Off
[1] Enable Complete AMA
[2] Enable Reduced AMA
1-3* Adv. Motor Data I
1-30 Stator Resistance (Rs)
0.000 ohm - 99.990 ohm
1-33 Stator Leakage Reactance
(X1)
0.000 ohm - 999.900 ohm
1-35 Main Reactance (Xh)
0.00 - 999.90 ohm
1-39 Motor Poles
2 - 100, * 4
1-4* Adv. Motor Data II
1-42 Motor Cable Length
0 - 150, * 50m
1-43 Motor Cable Length Feet
0 - 431, * 144
1-5* Load Indep. Setting
1-50 Motor Magnetisation at
Zero Speed
0 - 300, * 100%
1-52 Min Speed Normal
Magnetising [Hz]
0.0 - 10.0, * 0.0
1-55 U/f Characteristic - U
0 - 999 V, *0V
1-56 U/f Characteristic - F
0 - 400 Hz, *(0)
1-6* Load Depend. Setting
1-62 Slip Compensation
-400 - 399%, * 0%
11

Parameter Overview
1-63 Slip Compensation Time
Constant
0.05 - 5.00 s, * 0.10
1-64 Resonance Dampening
0 - 500%, * 100
1-65 Resonance Dampening Time
Constant
0.001 - 0.050 s, * 0.005
1-7* Start Adjustments
1-71 Start Delay
0.0 - 10.0 s, * 0.0
1-72 Start Function
[0] DC Hold/delay time
*[2] Coast/delay time
1-73 Flying Start
*[0] Disabled
[1] Enabled
1-8* Stop Adjustments
1-80 Function at Stop
*[0] Coast
[1] DC hold/MotorPreheat
1-82 Min Speed for Function at
Stop [Hz]
0.0 - 20.0 Hz, * 0.0
1-9* Motor Temperature
1-90 Motor Thermal Protection
*[0] No protection
[1] Thermistor warning
[2] Thermistor trip
[3] ETR warning 1
[4] ETR trip 1
1-93 Thermistor Resource
*[0] None
[1] Analog input 53
[6] Digital input 29
2-** Brakes
2-0* DC-Brake
2-00 DC Hold/Motor Preheat
Current
0 - 160%, * 50
2-01 DC Brake Current
0 - 150%, * 50
2-02 DC Braking Time
0.0 - 60.0 s, * 10.0
2-04 DC Brake Cut In Speed
0.0 - 400.0 Hz, * 0.0
2-1* Brake Energy Funct.
2-17 Over-voltage Control
[0] Disabled
*[2] Enabled
3-** Reference / Ramps
3-0* Reference Limits
3-02 Minimum Reference
(-4999.000) - 4999.000, * 0.000
3-03 Maximum Reference
(-4999.000) - 4999.000, * 50.000
3-1* References
3-10 Preset Reference
-100.00 - 100.00 %, * 0.00
3-11 Jog Speed [Hz]
0.0 - 400.0 Hz, * 5.0
3-14 Preset Relative Reference
-100.00 - 100.00, * 0.00
3-15 Reference Resource 1
[0] No function
*[1] Analog in 53
[2] Analog in 54
[11] Local bus reference
3-16 Reference 2 Resource
[0] No function
[1] Analog in 53
*[2] Analog in 54
[11] Local bus reference
3-17 Reference 3 Resource
[0] No function
[1] Analog in 53
[2] Analog in 54
*[11] Local bus reference
3-4* Ramp 1
3-41 Ramp 1 Ramp up Time
0.05 - 3600.00 s, *Size related
3-42 Ramp 1 Ramp Down Time
0.05 - 3600.00 s, *Size related
3-5* Ramp 2
3-51 Ramp 2 Ramp up Time
0.05 - 3600.00 s, *Size related
3-52 Ramp 2 Ramp down Time
0.05 - 3600.00 s, *Size related
3-8* Other Ramps
3-80 Jog Ramp Time
0.05 - 3600.00 s, *Size related
3-81 Quick Stop Ramp Time
0.05 - 3600.00 s, *Size related
4-** Limits / Warnings
4-1* Motor Limits
4-10 Motor Speed Direction
[0] Clockwise
*[2] Both directions
4-12 Motor Speed Low Limit [Hz]
0.0 - 400 Hz, * 0.0 Hz
4-14 Motor Speed High Limit
[Hz]
0.1 - 400 Hz, * 65.0 Hz
4-18 Current Limit
0 - 300%, * 110
4-19 Max Output Frequency
0.0 - 400.0 Hz, * 65.0
4-4* Adj. Warnings 2
4-40 Warning Freq. Low
0.0-400.0 Hz, *400.0
4-41 Warning Freq. High
0.0-400.0 Hz, *400.0
4-5* Adj. Warnings
4-50 Warning Current Low
0.00 - 194.00 A, * 0.00
4-51 Warning Current High
0.00 - 194.00 A, * 194.00
4-54 Warning Reference Low
-4999.000 - 4999.000, *-4999.000
4-55 Warning Reference High
-4999.000 - 4999.000, *4999.000
4-56 Warning Feedback Low
-4999.000 - 4999.000, *-4999.000
4-57 Warning Feedback High
-4999.000 - 4999.000, *4999.000
4-58 Missing Motor Phase
Function
[0] Off
*[1] On
4-6* Speed Bypass
4-61 Bypass Speed From [Hz]
0.0 - 400.0, * 0.0
4-63 Bypass Speed To [Hz]
0.0 - 400.0, * 0.0
4-64 Semi-Auto Bypass Set-up
*[0] Off
[1] Enable
5-** Digital In/Out
5-0* Digital I/O mode
5-00 Digital Input Mode
*[0] PNP
[1] NPN
5-03 Digital Input 29 Mode
*[0] PNP
[1] NPN
5-1* Digital Inputs
5-10 Terminal 18 Digital Input
[0] No operation
[1] Reset
[2] Coast inverse
[3] Coast and reset inverse
[4] Quick stop inverse
[5] DC-brake inverse
[6] Stop inverse
[7] External Interlock
*[8] Start
[9] Latched start
[10] Reversing
[11] Start reversing
[14] Jog
[16] Preset ref bit 0
[19] Freeze reference
[20] Freeze output
[21] Speed up
[22] Speed down
[23] Set-up select bit 0
[34] Ramp bit 0
[37] Fire mode
[52] Run permissive
[53] Hand Start
[54] Auto start
[60] Counter A (up)
[61] Counter A (down)
[62] Reset Counter A
[63] Counter B (up)
[64] Counter B (down)
[65] Reset Counter B
See par. 5-10, *[0] No operation
See par. 5-10, *[2] Coast inverse
See par. 5-10, *[14 Jog]
5-3* Digital Outputs
5-34 On Delay, Digital Output
0.00 - 600.00 s, *0.01 s
5-35 Off Delay, Digital Output
0.00 - 600.00 s, *0.01 s
5-4* Relays
5-40 Function Relay
*[0] No operation
[1] Control ready
[2] Drive ready
[3] Drive ready/remote control
[4] Enable / no warning
[5] VLT running
[6] Running / no warning
[7] Run in range/no warning
[8] Run on ref/no warning
[9] Alarm
[10] Alarm or warning
[12] Out of current range
[13] Below current, low
[14] Above current, high
[16] Below frequency, low
[17] Above frequency, high
[19] Below feedback, low
[20] Above feedback, high
[21] Thermal warning
[22] Ready, no thermal warning
[23] Remote, ready, no thermal
warning
[24] Ready, Voltage OK
[25] Reverse
[26] Bus OK
[36] Control word bit 11
[37] Control word bit 12
[45] Bus Control
[60] Comparator 0
[61] Comparator 1
[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic rule 0
71] Logic rule 1
[72] Logic rule 2
1 1

Parameter Overview
[73] Logic rule 3
[74] Logic rule 4
[75] Logic rule 5
[80] SL digital output A
[81] SL digital output B
[82] SL digital output C
[83] SL digital output D
[160] No alarm
[161] Running reverse
[165] Local ref. active
[166] Remote ref. active
[167] Start command activ
[168] Drive in hand mode
[169] Drive in auto mode
[193] Sleep Mode
[194] Broken Belt Function
[196] Fire Mode
[198] Drive Bypass
5-41 On Delay, Relay
0.00 - 600.00 s, *0.01 s
5-42 Off Delay, Relay
0.00 - 600.00 s, *0.01 s
5-5* Pulse Input
5-9* Bus Controlled
5-90 Digital and Relay Bus
Control
0 - 0xFFFFFFFF, * 0
6-** Analog In/Out
6-0* Analog I/O Mode
6-00 Live Zero Timeout Time
1 - 99s, * 10
6-01 Live Zero Timeout Function
*[0] Off
[1] Freeze output
[2] Stop
[3] Jogging
[4] Max. speed
[5] Stop and trip
6-1* Analog Input 53
0.00 - 10.00 V, * 0.07
0.00 - 10.00 V, * 10.00
0.00 - 20.00, * 4.00 mA
0.00 - 20.00, * 20.00 mA
6-14 Terminal 53 Low Ref./Feedb.
Value
-4999.000 - 4999.000, * 0.000
Feedb. Value
-4999.000 - 4999.000, * 50.000
Constant
0.01 - 10.00 s, * 0.01
6-19 Terminal 53 mode
[0] Current mode
*[1] Voltage mode
6-2* Analog Input 54
0.00 - 10.00V, * 0.07
0.00 - 10.00V, * 10.00
0.00 - 20.00, * 4.00mA
0.00 - 20.00, * 20.00mA
6-24 Terminal 54 Low Ref./Feedb.
Value
-4999.000 - 4999.000, * 0.000
Feedb. Value
-4999.000 - 4999.000, * 50.000
Constant
0.01 - 10.00, * 0.01
6-29 Terminal 54 mode [0]
Current mode
[0] Current mode
*[1] Voltage mode
6-7* Analog Output 45
*[0] 0-20 mA
[1] 4-20 mA
[2] Digital Output
6-71 Terminal 45 Analog Output
*[0] No operation
[100] Output frequency
[101] Reference
[102] Feedback
[103] Motor current
[106] Power
[139] Bus Control
6-72 Terminal 45 Digital Output
*[0] No operation
[1] Control ready
[2] Drive ready
[4] Standby / no warning
[5] Drive running
[9] Alarm
warning
[25] Reverse
[26] Bus OK
[45] Bus Control
[60] Comparator 0
[61] Comparator 1
[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic rule 0
[71] Logic rule 1
[72] Logic rule 2
[73] Logic rule 3
[74] Logic rule 4
[75] Logic rule 5
[160] No alarm
[193] Sleep Mode
[196] Fire Mode
[198] Bypass Mode
6-73 Terminal 45 Output Min
Scale
0.00 - 200.00%, * 0.00
6-74 Terminal 45 Output Max
Scale
0.00 - 200.00%, * 100.00
6-76 Terminal 45 Output Bus
Control
0.00 - 100.00%, * 0.00
6-9* Analog Output 42
*[0] 0-20 mA
[1] 4-20 mA
[2] Digital Output
6-91 Terminal 42 Analog Output
*[0] No operation
[100] Output frequency
[101] Reference
[102] Feedback
[103] Motor current
[105] TorquereltoRated
[106] Power
[139] Bus Control
6-92 Terminal 42 Digital Output
*[0] No operation
[1] Control ready
[2] Drive ready
[4] Enable / no warning
[5] Drive running
[9] Alarm
warning
[25] Reverse
[26] Bus OK
[45] Bus Control
[60] Comparator 0
[61] Comparator 1
[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic rule 0
[71] Logic rule 1
[72] Logic rule 2
[73] Logic rule 3
[74] Logic rule 4
[75] Logic rule 5
[160] No alarm
[193] Sleep Mode
[196] Fire Mode
[198] Drive Bypass
6-93 Terminal 42 Output Min
Scale
0.00 - 200.00%, * 0.00
6-94 Terminal 42 Output Max
Scale
0.00 - 200.00%, * 100.00
6-96 Terminal 42 Output Bus
Control
0.00 - 100.00%, * 0.00
8-** Comm. and Options
8-0* Comm. General Settings
8-01 Control Site
11

Parameter Overview
*[0] Digital and ctrl.word
[1] Digital only
[2] Controlword only
8-02 Control Source
[0] None
*[1] FC Port
8-03 Control Timeout Time
0.1 - 6500.0s, * 1.0
8-04 Control Timeout Function
*[0] Off
[1] Freeze output
[2] Stop
[3] Jogging
[4] Max. speed
[5] Stop and trip
[20] N2 Override Release
8-06 Reset Control Word Timeout
*[0] No function
[1] Do reset
8-3* FC Port Settings
8-30 Protocol
*[0] FC
[2] Modbus RTU
[3] Metasys N2
[4] FLN
[5] BACNet
8-31 Address
1 - 247 , * 1
8-32 FC Port Baud Rate
[0] 2400 Baud
[1] 4800 Baud
*[2] 9600 Baud
[3] 19200 Baud
[4] 38400 Baud
[5] 57600 Baud
[6] 76800 Baud
[7] 115200 Baud
8-33 FC Port Parity
*[0] Even Parity, 1 Stop Bit
[1] Odd Parity, 1 Stop Bit
[2] No Parity, 1 Stop Bit
[3] No Parity, 2 Stop Bits
8-35 Minimum Response Delay
0.001 - 0.500s, * 0.010
8-36 Max Response Delay
0.100 - 10.000s, *5.000
8-37 Max Inter-char delay
0.025 - 0.025s, * 0.025
8-5* Digital/Bus
8-50 Coasting Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-51 Quick Stop Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-52 DC Brake Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-53 Start Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-54 Reversing Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-55 Set-up Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-56 Preset Reference Select
[0] Digital input
[1] Bus
[2] Logic AND
*[3] Logic OR
8-7* Bacnet
8-70 BACnet Device Instance
0 - 0x400000UL
* 1
8-72 MS/TP Maxmaster
0 - 127, * 127
8-73 MS/TP Max Info Frames
1 - 65534, * 1
8-74 "I am" Service
*[0] Send at power-up
[1] Continuously
8-75 Intialisation Password
8-8* FC Port Diagnostics
8-80 Bus Message Count
0 - 65536, * 0
8-81 Bus Error Count
0 - 65536, * 0
8-82 Slave Message Rcvd
0 - 65536, * 0
8-83 Slave Error Count
0 - 65536, * 0
8-84 Slave Message Sent
0 - 65536, * 0
8-85 Slave Timeout Errors
0 - 65536, * 0
8-88 Reset FC port Diagnostics
*[0] Do not reset
[1] Reset counter
8-9* Bus Feedback
8-94 Bus feedback 1
-32768 - 32767, * 0
13-** Smart Logic
13-0* SLC Settings
13-00 SL Controller Mode
*[0] Off
[1] On
13-01 Start Event
[0] False
[1] True
[2] Running
[3] In range
[4] On reference
[8] Below Ilow
[9] Above Ihigh
[17] Mains out of range
[18] Reversing
[19] Warning
[20] Alarm (trip)
[21] Alarm (trip lock)
[22] Comparator 0
[23] Comparator 1
[24] Comparator 2
[25] Comparator 3
[26] Logic rule 0
[27] Logic rule 1
[28] Logic rule 2
[29] Logic rule 3
*[39] Start command
[40] Drive stopped
[41] Reset trip
[42] Auto reset trip
[43] Key Ok
[44] Key Reset
[47] Key Up
[48] Key Down
[50] Comparator 4
[51] Comparator 5
[60] Logic rule 4
[83] Broken belt
13-02 Stop Event
See par. 13-02, *[40] Drive stopped
13-03 Reset SLC
*[0] Do not reset
[1] Reset SLC
13-1* Comparators
13-10 Comparator Operand
*[0] Disabled
[1] Reference
[2] Feedback
[3] Motor speed
[4] Motor current
[6] Motor power
[7] Motor voltage
[8] DC-link voltage
[12] Analog in 53
[13] Analog in 54
[20] Alarm number
[30] Counter A
[31] Counter B
13-11 Comparator Operator
[0] Less Than
*[1] Approx. Equal
[2] GreaterThan
13-12 Comparator Value
-9999.0 - 9999.0, * 0.0
13-2* Timers
13-20 SL Controller Timer
0.00 - 3600.00, * 0.00
13-4* Logic Rules
13-40 Logic Rule Boolean 1
See par. 13-01, *[0] False
13-41 Logic Rule Operator 1
*[0] Disabled
[1] AND
[2] OR
[3] AND NOT
[4] OR NOT
[5] NOT AND
[6] NOT OR
[7] NOT AND NOT
[8] NOT OR NOT
13-43 Logic Rule Operator 2
See par. 13-41, *[0] Disabled
13-5* States
13-51 SL Controller Event
13-52 SL Controller Action
*[0] Disabled
[1] No action
[2] Select set-up 1
[3] Select set-up 2
[10] Select preset ref 0
[18] Select ramp 1
[19] Select ramp 2
[22] Run
[23] Run reverse
[24] Stop
[25] Qstop
[26] DC Brake
[27] Coast
[28] Freeze output
1 1

Parameter Overview
[29] Start timer 0
[30] Start timer 1
[31] Start timer 2
[32] Set digital out A low
[33] Set digital out B low
[34] Set digital out C low
[35] Set digital out D low
[38] Set digital out A high
[39] Set digital out B high
[40] Set digital out C high
[41] Set digital out D high
[60] Reset Counter A
[61] Reset Counter B
[70] Start timer 3
[71] Start timer 4
[72] Start timer 5
[73] Start timer 6
[74] Start timer 7
[100] Reset Alarm
14-** Special Functions
14-0* Inverter Switching
14-01 Switching Frequency
[0] Ran3
[1] Ran5
[2] 2.0 kHz
[3] 3.0 kHz
[4] 4.0 kHz
[5] 5.0 kHz
[6] 6.0 kHz
[7] 8.0 kHz
[8] 10.0 kHz
[9] 12.0kHz
[10] 16.0kHz
14-03 Overmodulation
[0] Off
*[1] On
14-08 Damping Gain Factor
0 - 100-%, * 96
14-1* Mains on/off
14-12 Function at Mains
Imbalance
*[0] Trip
[1] Warning
[2] Disabled
[3] Derate
14-2* Reset Functions
14-20 Reset Mode
*[0] Manual reset
[1] Automatic reset x 1
[13] Infinite auto reset
14-21 Automatic Restart Time
0 - 600s, * 10
14-22 Operation Mode
*[0] Normal operation
[2] Initialisation
14-27 Action At Inverter Fault
[0] Off
*[1] On
14-28 Production Settings
*[0] No action
[1] Service reset
[3] Software Reset
14-29 Service Code
0 - 0x7FFFFFFF, * 0
14-3* Current Limit Ctrl.
14-4* Energy Optimising
14-40 VT Level
40 - 90%, * 90%
14-41 AEO Minimum Magnetisation
40 - 75%, * 66
14-5* Environment
14-50 RFI Filter
[0] Off
*[1] On
14-51 DC-link Voltage Compen-
sation
[0] Off
*[1] On
14-52 Fan Control
*[0] Auto
[4] Auto Low temp env
14-53 Fan Monitor
[0] Disabled
*[1] Warning
[2] Trip
14-55 Output Filter
*[0] No Filter
[1] Sine-Wave Filter
[3] Sine-Wave Filter with Feedback
14-63 Min Switch Frequency
1 - 16kHz, * 1
15-** Drive Information
15-0* Operating Data
15-00 Operating Hours
0 - 2147483647, * 0
15-01 Running Hours
0 - 2147483647, * 0
15-02 kWh Counter
0 - 65535, * 0
15-03 Power Up's
0 - 2147483647, * 0
15-04 Over Temp's
0 - 65535, * 0
15-05 Over Volt's
0 - 65535, * 0
15-06 Reset kWh Counter
*[0] Do not reset
[1] Reset counter
15-07 Reset Running Hours
Counter
*[0] Do not reset
[1] Reset counter
15-3* Fault Log
15-30 Fault Log:
Error Code 0 - 255, * 0
15-4* Drive Identification
15-40 FC Type
15-41 Power Section
15-42 Voltage
15-43 Software Version
15-44 OrderedTypeCode
15-46 Frequency Converter
Ordering No
15-47 Power Card Ordering No
15-48 LCP Id No
15-49 Software ID Control Card
15-50 Software ID Power Card
15-51 Frequency Converter Serial
Number
15-53 Power Card Serial Number
16-** Data Readouts
16-0* General Status
16-00 Control Word
0 - 65535, * 0
16-01 Reference [Unit]
-4999.000 - 4999.000, * 0.000
16-02 Reference
% -200.0 - 200.0, * 0.0
16-03 Status Word
0 - 65535, * 0
16-05 Main Actual Value [%]
-200.00 - 200.00, * 0.00
16-09 Custom Readout
0.00 - 9999.00, * 0.00
16-1* Motor Status
16-10 Power [kW]
0.000-4.294, 967.500, *0.000
16-11 Power [hp]
0.000 - 2.294, 967.500 *0.000
16-3* Drive Status
16-30 DC Link Voltage
0 - 65535, * 0
16-34 Heatsink Temp.
0 - 255, * 0
16-35 Inverter Thermal
0 - 255%, * 0
16-36 Inv. Nom. Current
0.00 - 655.35, * 0.00
16-37 Inv. Max. Current
0.00 - 655.35
16-38 SL Controller State
0 - 255, * 0
16-5* Ref. and Feedb.
16-50 External Reference
-200.0 - 200.0%, * 0.0
16-52 Feedback
-4999.000 - 4999.000, * 0.000
16-6* Inputs and Outputs
16-60 Digital input
0 - 65535, * 0
16-61 Terminal 53 Setting
*[0] Current mode
[1] Voltage mode
16-62 Analog Input 53
0.00 - 10.00, * 1.00
16-63 Terminal 54 Setting
*[0] Current mode
[1] Voltage mode
16-64 Analog Input 54
0.00 - 20.00, * 1.00
16-65 Analog Output 42 [mA]
0.00 - 20.00, * 0.00
16-61 Digital Output
16-72 Counter A
-32768 - 32767, * 0
16-73 Counter B
-32768 - 32767, * 0
16-79 Analog output 45
20 - 20mA, * 0
16-8* Fieldbus / FC Port
16-86 FC Port REF 1
-32768 - 32767, * 0
16-9* Diagnosis Readouts
16-90 Alarm Word
0 - 0xFFFFFFFFUL, * 0
16-91 Alarm Word 2
0 - 0xFFFFFFFFUL, * 0
16-92 Warning Word
0 - 0x7FFFFFFFUL, * 0
16-93 Warning Word 2
16-94 Ext. Status Word
16-95 Ext. Status Word 2
18-**Extended Motor Data
18-1* Firemode Log
18-10 Firemode log: Event
0-255, *0
20-** FC Closed Loop
20-0* Feedback
20-00 Feedback 1 Source
*[0] No function
[1] Analog in 53
[2] Analog in 54
[100] Bus Feedback 1
11

Parameter Overview
20-01 Feedback 1 Conversion
*[0] Linear
[1] Square root
20-8* PI Basic Setting
20-81 Process PI Normal/ Inverse
Control
*[0] Normal
[1] Inverse
20-83 Process PI Start Speed[Hz]
0.0 - 200.0, * 0.0
20-84 On Reference Bandwidth
0 - 200%, * 5
20-9* PI Controller
20-91 PI Anti Windup
[0] Off
*[1] On
20-93 PI Proportional Gain
0.00 - 10.00, * 0.01
20-94 PI Integral Time
0.10 - 9999.00s, * 9999.00
20-97 Process PI Feed Forward Factor
0 - 400%, * 0
22-** Appl. functions
22-4* Sleep mode
22-40 Minimum Run Time
0 - 600 s, * 10
22-41 Minimum Sleep Time
0 - 600 s, * 10
22-43 Wake-Up Speed [Hz]
0.0 - 400.0, * 100.0
22-44 Wake-Up Ref./FB difference
0 - 100%, * 10
22-45 Setpoint Boost
-100 - 100%, * 0
22-46 Maximum Boost Time
0 - 600 s, * 60
22-47 Sleep Speed [Hz]
0.0 - 400.0, * 0.0
22-6* Broken Belt Detection
22-60 Broken Belt Detection
*[0] Off
[1] Warning
[2] Trip
22-61 Broken Belt Torque
5 - 100%, * 10
22-62 Broken Belt Delay
0 - 600 s, * 10
24-** Appl. functions 2
24-0* Fire mode
24-00 Fire Mode Function
*[0] Disabled
[1] Enabled Run Forward
[2] Enabled Run Reverse
[3] Enable-Coast
[4] Enabled - Run Fwd/Rev
24-05 Fire Mode Preset Reference
-100 - 100%, * 0
24-09 Fire Mode Alarm Handling
*[1] Trip, Critical Alarms
[2] Trip, All Alarms/Test
24-1* Drive Bypass
24-10 Drive Bypass Function
*[0] Disabled
[2] Enabled (Fire Mode only)
24-11 Bypass Delay Timer
0 - 600 s, * 0
1.6 Warnings and Alarms
Fault
number
Alarm/
Warning
Bit
Number Fault text Warning Alarm
Trip
locked Cause of problem
2 16 Live zero error X X
Signal on terminal 53 or 54 is less than 50% of value set in par.
6-10, 6-12, 6-20 or 6-22. See also parameter group 6-0X
4 14 Mains ph. loss X X X
Missing phase on supply side or too high voltage imbalance. Check
supply voltage. See parameter 14-12
7 11 DC over volt X X Intermediate circuit voltage exceeds limit.
8 10 DC under volt X X
Intermediate circuit voltage drops below “voltage warning low”
limit.
9 9
Inverter
overload X X More than 100% load for too long.
10 8
Motor ETR
over X X
Motor is too hot due to more than 100% load for too long. See
parameter 1-90
11 7 Motor th over X X
Thermistor or thermistor connection is disconnected. See parameter
1-90.
13 5 Over Current X X X Inverter peak current limit is exceeded.
14 2 Earth Fault X X Discharge from output phases to ground.
16 12 Short Circuit X X Short-circuit in motor or on motor terminals.
17 4 Ctrl.word TO X X
No communication to frequency converter. See parameter group
8-0X
24 50 Fan Fault X X The fan is not working (Only on 400 V 30-90 kW units).
30 19 U phase loss X X Motor phase U is missing. Check the phase. See parameter 4-58.
31 20 V phase loss X X Motor phase V is missing. Check the phase. See parameter 4-58.
32 21 W phase loss X X Motor phase W is missing. Check the phase. See parameter 4-58.
38 17 Internal fault X X Contact your local Danfoss supplier.
44 28 Earth Fault X X Discharge from output phases to ground.
47 23
Control
Voltage Fault X X X 24 V DC may be overloaded.
48 25
VDD1 Supply
Low X X Control voltage low. Please contact your local Danfoss supplier
1 1

Fault
number
Alarm/
Warning
Bit
Number Fault text Warning Alarm
Trip
locked Cause of problem
50
AMA
Calibration
failed X Contact your local Danfoss supplier.
51 15
AMA
Unom,Inom X
The setting of motor voltage, motor current and motor power is
presumably wrong. Check the settings.
52 AMA low Inom X The motor current is too low. Check the settings.
53
AMA big
motor X The motor is too big for the AMA to be carried out
54
AMA small
mot X The motor is too small for the AMA to be carried out
55
AMA par.
range X
The parameter values found from the motor are outside acceptable
range
56
AMA user
interrupt X The AMA has been interrupted by the user
57 AMA timeout X
Try to start the AMA again a number of times, until the AMA is
carried out. Please note that repeated runs may heat the motor to
a level where the resistance Rs and Rr are increased. In most cases,
however, this is not critical
58 AMA internal X X Contact your local Danfoss supplier.
59 25 Current limit X The current is higher than the value in par. 4-18 Current Limit
60 44
External
Interlock X
External interlock has been activated. To resume normal operation,
apply 24 V DC to the terminal programmed for external interlock
and reset the frequency converter (via serial communication, digital
I/O, or by pressing reset button on keypad).
66 26
Heat sink
Temperature
Low X
This warning is based on the temperature sensor in the IGBT
module (Only on 400 V 30-90 kW units).
69 1
Pwr. Card
Temp X X X
The temperature sensor on the power card is either too hot or too
cold.
79
Illegal power
section config-
uration X X Internal fault. Contact your local Danfoss supplier.
80 29
Drive
initialised X All parameter settings are initialized to default settings.
87 47
Auto DC
Braking X The drive is auto DC braking
95 40 Broken Belt X X
Torque is below the torque level set for no load, indicating a
broken belt. See parameter group 22-6.
200 Fire Mode X Fire mode has been activated
202
Fire Mode
Limits
Exceeded X Fire Mode has suppressed one or more warranty voiding alarms
250 New sparepart X X
The power or switch mode power supply has been exchanged.
(Only on 400 V 30-90 kW units). Contact your local Danfoss supplier
251 New Typecode X X
The frequency converter has a new type code (Only on 400 V 30-90
kW units). Contact your local Danfoss supplier.
11

1.7 General Specifications
1.7.1 Mains Supply 3 x 200-240 V AC
frequency converter PK2
5
PK3
7
PK7
5
P1K
5
P2K2 P3K
7
P5K5 P7K5 P11K P15K P18K P22K P30K P37K P45K
Typical shaft output (kW) 0.25 0.37 0.75 1.5 2.2 3.7 5.5 7.5 11.0 15.0 18.5 22.0 30.0 37.0 45.0
Typical shaft output (hp) 0.33 0.5 1.0 2.0 3.0 5.0 7.5 10.0 15.0 20.0 25.0 30.0 40.0 50.0 60.0
IP20 frame H1 H1 H1 H1 H2 H3 H4 H4 H5 H6 H6 H7 H7 H8 H8
Max. cable size in terminals (mains,
motor) [mm2/AWG]
4/10 4/10 4/10 4/10 4/10 4/10 16/6 16/6 16/6 35/2 35/2 50/1 50/1 95/0 120/
(4/0)
Output current
RELAY 2
130BB632.10
40°C ambient temperature
Continuous
(3 x 200-240 V)
[A]
1.5 2.2 4.2 6.8 9.6 15.2 22.0 28.0 42.0 59.4 74.8 88.0 115.0 143.0 170.0
Intermittent
(3 x 200-240 V)
[A]
1.7 2.4 4.6 7.5 10.6 16.7 24.2 30.8 46.2 65.3 82.3 96.8 126.5 157.3 187.0
Max. input current
RELAY 2
130BB633.10
Continuous
(3 x 200-240 V)
[A]
1.1 1.6 2.8 5.6 8.6/7
.2
14.1
/
12.0
21.0/
18.0
28.3/
24.0
41.0/
38.2
52.7 65.0 76.0 103.7 127.9 153.0
Intermittent
(3 x 200-240 V)
[A]
1.2 1.8 3.1 6.2 9.5/7
.9
15.5
/
13.2
23.1/
19.8
31.1/
26.4
45.1/
42.0
58.0 71.5 83.7 114.1 140.7 168.3
Max. mains fuses See 1.3.6 Fuses
Estimated power
loss [W], Best
case/typical1)
12/1
4
15/1
8
21/2
6
48/6
0
80/1
02
97/1
20
182/
204
229/
268
369/
386
512 658 804 1015 1459 1350
Weight enclosure
IP20 [kg]
2. 2.0 2.0 2.1 3.4 4.5 7.9 7.9 9.5 24.5 24.5 36.0 36.0 51.0 51.0
Efficiency [%],
Best case/Typical
1
97.0
/
96.5
97.3
/
96.8
98.0/
97.6
97.6
/
97.0
97.1/
96.3
97.9
/
97.4
97.3/
97.0
98.5/
97.1
97.2/
97.1
97.0 96.9 96.8 97.0 96.5 97.3
Output current
Continuous (3 x
200-240 V) [A]
1.5 1.9 3.5 6.8 9.6 13.0 19.8 23.0 33.0 53.5 66.6 79.2 103.5 128.7 153.0
Intermittent (3 x
200-240 V) [A]
1.7 2.1 3.9 7.5 10.6 14.3 21.8 25.3 36.3 58.9 73.3 87.1 113.9 141.6 168.3
1) At rated load conditions
1 1

FrequencyconverterPK37PK75P1K5P2K2P3K0P4K0P5K5P7K5P11KP15KP18KP22KP30KP37KP45KP55KP75KP90K
Typicalshaftoutput(kW)0.370.751.52.23.04.05.57.511.015.018.522.030.037.045.055.075.090.0
Typicalshaftoutput(hp)0.51.02.03.04.05.07.510.015.020.025.030.040.050.060.070.0100.0125.0
IP20frameH1H1H1H2H2H2H3H3H4H4H5H5H6H6H6H7H7H8
Max.cablesizeinterminals(mains,motor)
[mm2/AWG]
4/104/104/104/104/104/104/104/1016/616/616/616/635/235/235/250/195/0120/25
0MCM
Outputcurrent
RELAY2
130BB632.10
40°Cambienttemperature
Continuous(3x
380-440V)[A]
1.22.23.75.37.29.012.015.523.031.037.042.561.073.090.0106.0147.0177.0
Intermittent(3
x380-440V)
[A]
1.32.44.15.87.99.913.217.125.334.040.746.867.180.399.0116.0161.0194.0
Continuous(3x
440-480V)[A]
1.12.13.44.86.38.211.014.021.027.034.040.052.065.080.0105.0130.0160.0
Intermittent(3
x440-480V)
[A]
1.22.33.75.36.99.012.115.423.129.737.444.057.271.588.0115.0143.0176.0
Max.inputcurrent
RELAY2
130BB633.10
Continuous(3x
380-440V)[A]
1.22.13.54.76.38.311.215.122.129.935.241.557.070.084.0103.0140.0166.0
Intermittent(3
x380-440V)
[A]
1.32.33.95.26.99.112.316.624.332.938.745.762.777.092.4113.0154.0182.0
Continuous(3x
440-480V)[A]
1.01.82.93.95.36.89.412.618.424.729.334.649.260.672.588.6120.9142.7
Intermittent(3
x440-480V)
[A]
1.12.03.24.35.87.510.313.920.227.232.238.154.166.779.897.5132.9157.0
Max.mainsfusesSee5.1.4Fuses
11

FrequencyconverterPK37PK75P1K5P2K2P3K0P4K0P5K5P7K5P11KP15KP18KP22KP30KP37KP45KP55KP75KP90K
Estimatedpowerloss[W],Bestcase/typical1)13/1516/2146/5746/5866/8395/118104/13
1
159/19
8
248/27
4
353/37
9
412/45
6
475/52
3
7808931160113014601780
WeightenclosureIP20kg]2.02.02.13.33.33.44.34.57.97.99.59.524.524.524.536.036.051.0
Efficiency[%],Bestcase/Typical197.8/97.
3
98.0/97
.6
97.7/97
.2
98.3/97
.9
98.2/97.
8
98.0/97.
6
98.4/98
.0
98.2/9
7.8
98.1/9
7.9
98.0/9
7.8
98.1/9
7.9
98.1/9
7.9
97.897.997.198.398.398.3
Outputcurrent
Continuous(3x
380-440V)[A]
1.041.933.74.856.38.410.914.020.928.034.138.048.858.472.074.2102.9123.9
Intermittent(3x
380-440V)[A]
1.12.14.075.46.99.212.015.423.030.837.541.853.764.279.281.6113.2136.3
Continuous(3x
440-480V)[A]
1.01.83.44.45.57.510.012.619.124.031.335.041.652.064.073.591.0112.0
Intermittent(3x
440-480V)[A]
1.12.03.74.86.18.311.013.921.026.434.438.545.857.270.480.9100.1123.2
1 1

FrequencyconverterPK75P1K5P2K2P3K0P4KOP5K5P7K5P11KP15KP18KP22KP30KP37KP45KP55KP75KP90K
Typicalshaftoutput(kW)0.751.52.23.04.05.57.5111518.522.030.037.045.055.075.090.0
Typicalshaftoutput(hp)1.02.03.04.05.07.510.015.02025.030.040.050.060.070.0100.0125.0
IP54frameI2I2I2I2I2I3I3I5I5I5I6I6I6I7I7I8I8
Max.cablesizeinterminals(mains,motor)
[mm2/AWG]
4/104/104/104/104/104/104/1010/710/710/735/235/235/250/150/195/
(3/0)
120/
(4/0)
Outputcurrent
Continuous(3x
380-440V)[A]
2.23.75.37.29.012.015.5243237.544.061.073.090.0106.0147.0177.0
Intermittent(3x
380-440V)[A]
2.44.15.87.99.913.217.126.235.241.348.467.180.399.0116.6161.7194.7
Continuous(3x
440-480V)[A]
2.13.44.86.38.211.014.021273440.052.065.080.0105.0130.0160.0
Intermittent(3x
440-480V)[A]
2.33.75.36.99.012.115.423.129.737.444.057.271.588.0115.5143.0176.0
Max.inputcurrent
Continuous(3x
380-440V)[A]
2.13.54.76.38.311.215.122293441.857.070.384.2102.9140.3165.6
Intermittent(3x
380-440V)[A]
2.33.95.26.99.112.316.624.231.937.346.062.777.492.6113.1154.3182.2
Continuous(3x
440-480V)[A]
1.82.93.95.36.89.412.619253136.049.260.672.588.6120.9142.7
Intermittent(3x
440-480V)[A]
2.03.24.35.87.510.313.920.927.534.139.654.166.779.897.5132.9157.0
Max.mainsfuses
11

FrequencyconverterPK75P1K5PK2K2PK3KOPK4KOPK5K5PK7K5PK11KPK15KP18KP22KP30KP37KP45KP55KP75KP90K
Estimatedpowerloss[W],Bestcase/typical1)2171646/5746/5866/8395/118104/13
1
159/19
8
242330396496734705927107514251469
WeightenclosureIP54kg]5.35.35.35.35.37.27.223232327272745456565
Efficiency[%],Bestcase/Typical198.0/97.
6
97.7/97.
2
98.3/97.
9
98.2/97.
8
98.0/97.
6
98.4/98.
0
98.2/97.
8
98989898.097.898.398.398.398.398.5
Outputcurrent
Continuous(3x
380-440V)[A]
1.933.74.856.38.410.914.019.225.63035.248.858.463.074.2102.9123.9
Intermittent(3x
380-440V)[A]
2.14.075.46.99.212.015.421.228.23338.753.964.269.381.6113.2136.3
Continuous(3x
440-480V)[A]
1.83.44.45.57.510.012.616.821.627.232.041.652.056.073.591.0112.0
Intermittent(3x
440-480V)[A]
2.03.74.86.18.311.013.918.523.83035.245.857.261.680.9100.1123.2
1 1

Frequency converter P2K2 P3K0 P5K5 P7K5 P11K P15K P22K P30K P45K P55K P75K P90K
Typical shaft output (kW) 2.2 3.0 5.5 7.5 11.0 15.0 22.0 30.0 45.0 55.0 75.0 90.0
Typical shaft output (hp) 3.0 4.0 7.5 10.0 15.0 20.0 30.0 40.0 60.0 70.0 100.0 125.0
IP20 frame H9 H9 H9 H9 H10 H10 H6 H6 H7 H7 H8 H8
Max. cable size in terminals (mains, motor) [mm2/
AWG]
4/10 4/10 4/10 4/10 10/8 10/8 35/2 35/2 50/1 50/1 95/0 120/
(4/0)
Output current
RELAY 2
130BB632.10
Continuous (3 x
525-550 V) [A]
4.1 5.2 9.5 11.5 19.0 23.0 36.0 43.0 65.0 87.0 105.0 137.0
Intermittent (3 x
525-550 V) [A]
4.5 5.7 10.5 12.7 20.9 25.3 39.6 47.3 71.5 95.7 115.5 150.7
Continuous (3 x
551-600 V) [A]
3.9 4.9 9.0 11.0 18.0 22.0 34.0 41.0 62.0 83.0 100.0 131.0
Intermittent (3 x
551-600 V) [A]
4.3 5.4 9.9 12.1 19.8 24.2 37.4 45.1 68.2 91.3 110.0 144.1
Max. input current
RELAY 2
130BB633.10
Continuous (3 x
525-550 V) [A]
3.7 5.1 8.7 11.9 16.5 22.5 33.1 45.1 66.5 81.3 109.0 130.9
Intermittent (3 x
525-550 V) [A]
4.1 5.6 9.6 13.1 18.2 24.8 36.4 49.6 73.1 89.4 119.9 143.9
Continuous (3 x
551-600 V) [A]
3.5 4.8 8.3 11.4 15.7 21.4 31.5 42.9 63.3 77.4 103.8 124.5
Intermittent (3 x
551-600 V) [A]
3.9 5.3 9.2 12.5 17.3 23.6 34.6 47.2 69.6 85.1 114.2 137.0
Max. mains fuses
Estimated power loss [W], Best case/typical1) 8.4 112.0 178.0 239.0 360.0 503.0 607.0 820.0 972.0 1182.
0
1281.
0
1437.
0
Weight enclosure IP54 kg] 6.6 6.6 6.6 6.6 11.5 11.5 24.5 24.5 36.0 36.0 51.0 51.0
Efficiency [%], Best case/Typical 1 97.0 97.0 97.0 97.0 97.0 97.0 97.5 97.5 98.0 98.0 98.4 98.5
Output current
Continuous (3 x
525-550 V) [A]
2.9 3.6 6.7 8.1 13.3 16.1 25.2 30.1 45.5 60.9 73.5 95.9
Intermittent (3 x
525-550 V) [A]
3.2 4.0 7.4 8.9 14.6 17.7 27.7 33.1 50.0 67.0 80.9 105.5
Continuous (3 x
551-600 V) [A]
2.7 3.4 6.3 7.7 12.6 15.4 23.8 28.7 43.3 58.1 70.0 91.7
Intermittent (3 x
551-600 V) [A]
3.0 3.7 6.9 8.5 13.9 16.9 26.2 31.6 47.7 63.9 77.0 100.9
11

1.7.5 EMC Test Results
The following test results have been obtained using a system with a frequency converter, a screened control cable, a control
box with potentiometer, as well as a motor screened cable.
RFI Filter Type Conduct emission. Maximum shielded cable length (m) Radiated emission
Industrial environment
Housing, trades and
light industries
Industrial
environment
Housing, trades and
light industries
EN 55011 Class A2 EN 55011 Class A1 EN 55011 Class B EN 55011 Class A1 EN 55011 Class B
Without
external
filter
With
external
filter
Without
external
filter
With
external
filter
Without
external
filter
With
external
filter
Without
external
filter
With
external
filter
Without
external
filter
With
external
filter
H4 RFI filter
(Class A1)
0.25-11 kW
3 x 200-240 V
IP20
25 50 20 Yes Yes -
0.37-22 kW
3 x 380-480 V
IP20
25 50 20 Yes Yes -
H2 RFI filter
(Class A2)
15-45 kW
3 x 200-240 V
IP20
25 No -
30-90 kW
3 x 380-480 V
IP20
25 No -
0.75-18.5 kW
3 x 380-480 V
IP54
25 Yes
22-90 kW
3 x 380-480 V
IP54
25 No -
H3 RFI filter
(Class A1/B)
15-45 kW
3 x 200-240 V
IP20
50 20 Yes -
30-90 kW
3 x 380-480 V
IP20
50 20 Yes -
0.75-18.5 kW
3 x 380-480 V
IP54
25 10 Yes
22-90 kW
3 x 380-480 V
IP54
50 10 Yes -
1 1

Protection and features
• Electronic thermal motor protection against overload.
• Temperature monitoring of the heatsink ensures that the frequency converter trips in case of overtemperature.
• The frequency converter is protected against short-circuits between motor terminals U, V, W.
• If a motor phase is missing, the frequency converter trips and issues an alarm.
• If a mains phase is missing, the frequency converter trips or issues a warning (depending on the load).
• Monitoring of the intermediate circuit voltage ensures that the frequency converter trips if the intermediate circuit
voltage is too low or too high.
• The frequency converter is protected against earth faults on motor terminals U, V, W.
Mains supply (L1, L2, L3)
Supply voltage 200-240 V ±10%
Supply frequency 50/60 Hz
Max. imbalance temporary between mains phases 3.0% of rated supply voltage
True Power Factor (λ) ≥ 0.9 nominal at rated load
Displacement Power Factor (cosφ) near unity (> 0.98)
Switching on the input supply L1, L2, L3 (power-ups) enclosure frame H1-H5, I2, I3 Max. 2 times/min.
Switching on the input supply L1, L2, L3 (power-ups) enclosure frame H6-H8, I6-I8 Max. 1 time/min.
Environment according to EN 60664-1 overvoltage category III/pollution degree 2
The unit is suitable for use on a circuit capable of delivering not more than 100.000 RMS symmetrical Amperes, 240/480 V
maximum.
Motor output (U, V, W)
Output voltage 0 - 100% of supply voltage
Output frequency 0-200 Hz (VVCplus), 0-400 Hz (u/f)
Switching on output Unlimited
Ramp times 0.05 - 3600 sec.
Cable lengths and cross sections
Max. motor cable length, screened/armoured (EMC correct installation) See 1.7.5 EMC Test Results
Max. motor cable length, unscreened/unarmoured 50 m
Max. cross section to motor, mains*
Cross section DC terminals for filter feedback on enclosure frame H1-H3, I2, I3 4 mm2/11 AWG
Cross section DC terminals for filter feedback on enclosure frame H4-H5 16 mm2/6 AWG
Maximum cross section to control terminals, rigid wire 2.5 mm2/14 AWG)
Maximum cross section to control terminals, flexible cable 2.5 mm2/14 AWG)
Minimum cross section to control terminals 0.05 mm2/30 AWG
*See tables for mains supply for more information
Digital inputs:
Programmable digital inputs 4
Terminal number 18, 19, 27, 29
Logic PNP or NPN
Voltage level 0-24 V DC
Voltage level, logic '0' PNP < 5 V DC
Voltage level, logic '1' PNP > 10 V DC
Voltage level, logic '0' NPN > 19 V DC
Voltage level, logic '1' NPN < 14 V DC
Maximum voltage on input 28 V DC
Input resistance, Ri Approx. 4 k
Digital input 29 as thermistor input Fault: > 2.9 kΩ and no fault: < 800Ω
11

Analog inputs
Number of analog inputs 2
Terminal number 53, 54
Terminal 53 mode Parameter 6-19: 1 = voltage, 0 = current
Terminal 54 mode Parameter 6-29: 1 = voltage, 0= current
Voltage level 0 - 10 V
Input resistance, Ri approx. 10 kΩ
Max. voltage 20 V
Current level 0/4 to 20 mA (scalable)
Input resistance, Ri <500Ω
Max. current 29 mA
Analog output
Number of programmable analog outputs 2
Terminal number 42, 451)
Current range at analog output 0/4 - 20 mA
Max. load to common at analog output 500 Ω
Max. voltage at analog output 17 V
Accuracy on analog output Max. error: 0.4 % of full scale
Resolution on analog output 10 bit
1) Terminal 42 and 45 can also be programmed as digital outputs.
Digital output
Number of digital outputs 2
Terminal number 42, 451)
Voltage level at digital output 17 V
Max. output current at digital output 20 mA
Max. load at digital output 1 kΩ
1) Terminals 42 and 45 can also be programmed as analog output.
Control card, RS485 serial communication
Terminal number 68 (P, TX+, RX+), 69 (N, TX-, RX-)
Terminal number 61 Common for terminals 68 and 69
Control card, 24 V DC output:
Terminal number 12
Max. load enclosure frame H1-H8, I2-I8 80 mA
Relay output
Programmable relay output 2
Relay 01 and 02 01-03 (NC), 01-02 (NO), 04-06 (NC), 04-05 (NO)
Max. terminal load (AC-1)1) on 01-02/04-05 (NO) (Resistive load) 250 V AC, 3A
Max. terminal load (AC-15)1) on 01-02/04-05 (NO) (Inductive load @ cosφ 0.4) 250 V AC, 0.2A
Max. terminal load (DC-1)1) on 01-02/04-05 (NO) (Resistive load) 30 V DC, 2A
Max. terminal load (DC-13)1) on 01-02/04-05 (NO) (Inductive load) 24 V DC, 0.1A
Max. terminal load (AC-1)1) on 01-03/04-06 (NC) (Resistive load) 250 V AC, 3A
Max. terminal load (AC-15)1) on 01-03/04-06 (NC) (Inductive load @ cosφ 0.4) 250 V AC, 0.2A
Max. terminal load (DC-1)1) on 01-03/04-06
(NC) (Resistive load)
30 V DC, 2A
Min. terminal load on 01-03 (NC), 01-02 (NO) 24 V DC 10 mA, 24 V AC 20 mA
Environment according to EN 60664-1 Overvoltage category III/pollution degree 2
1) IEC 60947 parts 4 and 5.
Control card, 10V DC output
Terminal number 50
Output voltage 10.5 V ±0.5 V
Max. load 25 mA
1 1

All inputs, outputs, circuits, DC supplies and relay contacts are galvanically isolated from the supply voltage (PELV) and
other high-voltage terminals.
Surroundings
Enclosure IP20
Enclosure kit available IP21, TYPE 1
Vibration test 1.0 g
Max. relative humidity 5% - 95% (IEC 60721-3-3; Class 3K3 (non-condensing) during operation
Aggressive environment (IEC 60721-3-3), coated (standard) frame H1-H5 Class 3C3
Aggressive environment (IEC 60721-3-3), non-coated frame H6-H10 Class 3C2
Aggressive environment (IEC 60721-3-3), coated (optional) frame H6-H10 Class 3C3
Test method according to IEC 60068-2-43 H2S (10 days)
Ambient temperature See max. output current at 40/50° C in the tables mains supply
Derating for high ambient temperature, see section on special conditions
Minimum ambient temperature during full-scale operation 0° C
Minimum ambient temperature at reduced performance, enclosure frame H1-H5 -20° C
Minimum ambient temperature at reduced performance, enclosure frame H6-H10 -10° C
Temperature during storage/transport -30 - +65/70° C
Maximum altitude above sea level without derating 1000 m
Maximum altitude above sea level with derating 3000 m
Derating for high altitude, see section on special conditions
Safety standards EN/IEC 61800-5-1, UL 508C
EMC standards, Emission EN 61800-3, EN 61000-6-3/4, EN 55011, IEC 61800-3
EMC standards, Immunity
EN 61800-3, EN 61000-3-12, EN 61000-6-1/2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN
61000-4-5, EN 61000-4-6
1.8 Special Conditions
1.8.1 Derating for Ambient Temperature
and Switching Frequency
The ambient temperature measured over 24 hours should
be at least 5°#C lower than the max. ambient temperature.
If the frequency converter is operated at high ambient
temperature, the continuous output current should be
decreased. For derating curve, please see Design Guide
MG18C3YY.
1.8.2 Derating for Low Air Pressure
The cooling capability of air is decreased at low air
pressure. For altitudes above 2000 m, please contact
Danfoss regarding PELV. Below 1000 m altitude no de-
rating is necessary, but above 1000 m the ambient
temperature or the maximum output current should be
decreased. Decrease the output by 1% per 100 m altitude
above 1000 m or reduce the max. ambient temperature by
1° per 200 m.
1.9 Options for VLT HVAC Basic Drive FC101
For options please see the Design Guide MG18C3YY.
11

Vlt hvac basic_quick_start_guide_fc101

More Related Content

What's hot (19)

Similar to Vlt hvac basic_quick_start_guide_fc101 (20)

More from Toàn Huỳnh (20)

Recently uploaded (20)

Vlt hvac basic_quick_start_guide_fc101