Honeywell 5800zbridge-zstat-integration-programming-guide
0 likes322 views
This document provides instructions for programming a Honeywell ZSTAT thermostat and connecting it to a Honeywell 5800ZBRIDGE module. It outlines the basic setup fields that must be programmed on the thermostat, including date, time, schedule format, and temperature setpoints. It then describes how to enroll the house ID in the Z-Bridge module and how to enroll the Z-Bridge module into the thermostat to enable their connection. Key steps include changing a field from 0 to 1 on the thermostat to initiate learning of the Z-Bridge module.
Honeywell 5800zbridge-zstat-integration-programming-guide
- 1. Basic Programming for the Honeywell ZSTAT Thermostat and 5800ZBRIDGE Notes before you begin: • If you need help wiring your thermostat, please call 1-800-468-1502 o If required please have a licensed professional install your product for you. Programming the thermostat: 1. Press System: 2. Press the 3rd and 5th buttons simultaneously 3. Used the following buttons to program: Use the Up and Use the Up and down down arrows to arrows to scroll through the enter the desired questions (fields). value. Tech Support -1- Updated 6/7/11
- 2. The Follow locations are the bare minimum fields required for operation: Setup Functions (Fields) Settings & Options (Factory default is in bold) 0120 Year (First 2 Digits) 20 (2000-2078) 0130 Year (Second 2 Digits) 11 (2011) 0140 Month 6 (1-12) 0150 Date 15 (1-31) 0160 Schedule Format 0 (Non Programmable) (Does not affect Z-Wave Operation) 4 (Programmable) 0615 Energy Saving Heat Setpoint 65°F (18.5°C) 40-90°F (4.5°C-32°C) 0616 Energy Saving Cool Setpoint 78°F (25.5°C) 50-99°F (10°C-37°C) Enrolling the House ID in the Z-Bridge Module: 1. Make sure your House ID is set in the panel or local mode of the RF keypads. a. The following devices are compatible • 6150rf • 6160rf • 5883H • Lynx Control Panels 2. Press the SW5 Learn switch for 1 second then release. a. LED will Flash Orange 3. Arm and disarm the control panel. a. The LED will now show status of the panel. Enrolling the Z-Bridge Module into the Honeywell Z-wave thermostat: 1. Navigate through the programming of the thermostat until you reach the following screen: Tech Support -2- Updated 6/7/11
- 3. 2. Next power up the Z-Bridge with the supplied 12v power supply. a. Upon power up the yellow LED will flash 3 times. 3. Press the corresponding switch (1-4) for 1 second then release for any combination of four Thermostats or Lights. a. Switch 1 = Thermostat/Light 1 b. Switch 2 = Thermostat/Light 2 c. Switch 3 = Thermostat/Light 3 d. Switch 4 = Thermostat/Light 4 The LED on the Z-Bridge will begin flashing green. 4. On the Thermostat, change the 0 to a 1 to learn the Z-Bridge. Change this value to a 1. Once that is done you will see Once learned in the LED will flash three times and return to the status of the control panel. 5. Press ‘Done’ to exit programming. Notes: 1. To test the connectivity simply arm and disarm the panel and watch the LED on the Z-Bridge to make sure it is illuminating properly (See Z-Bridge Installation Instructions). 2. To verify the Z-Bridge is communicating with the Thermostat look for the word ‘Saving’ which will be present above the ‘Set To’ temperature. This represents the thermostat is in “Setback Mode’. 3. Locations 0615 (Heat Set Back) and 0616 (Cool Set Back) are End User Programmable. (See the thermostat Owner’s Manual for more information) Tech Support -3- Updated 6/7/11