8 interrupt 8051

8051
Interrupts

M_Nokhodchian @ yahoo.com Microprocessors 1-1

Interrupts Programming
 An interrupt is an external or internal event that
interrupts the microcontroller to inform it that a
device needs its service.
Interrupts vs. Polling
 A single microcontroller can serve several devices.
 There are two ways to do that:
 interrupts
 polling.
 The program which is associated with the interrupt
is called the interrupt service routine (ISR) or
interrupt handler.


Steps in executing an interrupt
 Finish current instruction and saves the PC on stack.

 Jumps to a fixed location in memory depend on type
of interrupt

 Starts to execute the interrupt service routine until
RETI (return from interrupt)

 Upon executing the RETI the microcontroller returns
to the place where it was interrupted. Get pop PC
from stack


Interrupt Sources
 Original 8051 has 6 sources of interrupts
 Reset
 Timer 0 overflow
 Timer 1 overflow
 External Interrupt 0
 External Interrupt 1
 Serial Port events (buffer full, buffer empty, etc)

 Enhanced version has 22 sources
 More timers, programmable counter array, ADC, more
external interrupts, another serial port (UART)


Interrupt Vectors
Each interrupt has a specific place in code memory where
program execution (interrupt service routine) begins.

External Interrupt 0: 0003h
Timer 0 overflow: 000Bh
External Interrupt 1: 0013h
Timer 1 overflow: 001Bh
Note: that there are
Serial : 0023h only 8 memory
Timer 2 overflow(8052+) 002bh locations between
vectors.


ISRs and Main Program in 8051
SJMP main
ORG 03H
ljmp int0sr
ORG 0BH
ljmp t0sr
ORG 13H
ljmp int1sr
ORG 1BH
ljmp t1sr
ORG 23H
ljmp serialsr
ORG 30H
main:
…
END


Interrupt Enable (IE) register

All interrupt are disabled after reset
We can enable and disable them bye IE


Enabling and disabling an
interrupt
by bit operation
Recommended in the middle of program
SETB EA SETB IE.7 ;Enable All
SETB ET0 SETB IE.1 ;Enable Timer0 ovrf
SETB ET1 SETB IE.3 ;Enable Timer1 ovrf
SETB EX0 SETB IE.0 ;Enable INT0
SETB EX1 SETB IE.2 ;Enable INT1
SETB ES ;Enable Serial port
SETB IE.4
by mov instruction
Recommended in the first of program
MOV IE, #10010110B


Example
 A 10khz square wave with 50% duty cycle
ORG 0 ;Reset entry poit
LJMP MAIN ;Jump above interrupt

ORG 000BH ;Timer 0 interrupt vector
T0ISR:CPL P1.0 ;Toggle port bit
RETI ;Return from ISR to Main program

ORG 0030H ;Main Program entry point
MAIN: MOV TMOD,#02H ;Timer 0, mode 2
MOV TH0,#-50 ;50 us delay
SETB TR0 ;Start timer
MOV IE,#82H ;Enable timer 0 interrupt
SJMP $ ;Do nothing just wait
END

Example
 Write a program using interrupts to
simultaneously create 7 kHz and 500 Hz
square waves on P1.7 and P1.6.

8051 143µs
71µs
P1.7

2ms
P1.6 1ms


ORG 0 Solution
LJMP MAIN
ORG 000BH
LJMP T0ISR
ORG 001BH
LJMP T1ISR 8051 143µs
ORG 0030H 71µs
P1.7
MAIN: MOV TMOD,#12H
MOV TH0,#-71
SETB TR0
SETB TF1
MOV IE,#8AH 2ms
MOV IE,#8AH P1.6 1ms
SJMP $
T0ISR: CPL P1.7
RETI
T1ISR: CLR TR1
MOV TH1,#HIGH(-1000)
MOV TL1,#LOW(-1000)
SETB TR1
CPL P1.6
RETI
END


Timer ISR
 Notice that
 There is no need for a “CLR TFx” instruction in
timer ISR
 8051 clears the TF internally upon jumping to ISR

 Notice that
 We must reload timer in mode 1
 There is no need on mode 2 (timer auto reload)


External interrupt type control
 By low nibble of Timer control register TCON
 IE0 (IE1): External interrupt 0(1) edge flag.
 set by CPU when external interrupt edge (H-to-L) is detected.
 Does not affected by H-to-L while ISR is executed(no int on int)
 Cleared by CPU when RETI executed.
 does not latch low-level triggered interrupt
 IT0 (IT1): interrupt 0 (1) type control bit.
 Set/cleared by software
 IT=1 edge trigger
 IT=0 low-level trigger

(MSB) (LSB)
TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0
Timer 1 Timer0 for Interrupt

External Interrupts

(Level-triggered (default
INT0
(Pin 3.2) 0
0003
IT0
1 (IE0 (TCON.3
2

Edge-triggered

(Level-triggered (default
INT0
(Pin 3.3) 0 0013
IT1
1 (IE1 (TCON.3
2

Edge-triggered


Example of external interuupt
ORG 0000H
LJMP MAIN
;
;interrupt service routine (ISR)
;for hardware external interrupt INT1
;

ORG 0013H
SETB P1.1
MOV R0,200
WAIT: DJNZ R0,WAIT
CLR P1.1
RETI
;
;main program for initialization
;
ORG 30H
MAIN: SETB IT1 ;on negative edge of INT1
MOV IE,#10000100B
WAIT2: SJMP WAIT2
END


Org 0000h
Ljmp main

Org 0003h
x0isr: clr p1.7
Reti

Org 0013h
x1isr: setb p1.7
Reti

Org 0030h
Main: mov ie,#85h
Setb it0
Setb it1
Setb p1.7
Jb p3.2,skip
Clr p1.7
Skip: Sjmp $
end

Interrupt Priorities
 What if two interrupt sources interrupt at the same
time?
 The interrupt with the highest PRIORITY gets
serviced first.
 All interrupts have a power on default priority order.
1. External interrupt 0 (INT0)
2. Timer interrupt0 (TF0)
3. External interrupt 1 (INT1)
4. Timer interrupt1 (TF1)
5. Serial communication (RI+TI)
 Priority can also be set to “high” or “low” by IP reg.


Interrupt Priorities (IP) Register

--- --- PT2 PS PT1 PX1 PT0 PX0

IP.7: reserved
IP.6: reserved
IP.5: timer 2 interrupt priority bit(8052 only)
IP.4: serial port interrupt priority bit
IP.3: timer 1 interrupt priority bit
IP.2: external interrupt 1 priority bit
IP.1: timer 0 interrupt priority bit
IP.0: external interrupt 0 priority bit


Interrupt Priorities Example

 MOV IP , #00000100B or SETB IP.2 gives priority order
1. Int1
2. Int0
3. Timer0
4. Timer1
5. Serial
 MOV IP , #00001100B gives priority order
1. Int1
2. Timer1
3. Int0
4. Timer0
5. Serial


Interrupt inside an interrupt

 A high-priority interrupt can interrupt a low-priority
interrupy
 All interrupt are latched internally
 Low-priority interrupt wait until 8051 has finished
servicing the high-priority interrupt


8 interrupt 8051

More Related Content

What's hot (20)

Viewers also liked (6)

Similar to 8 interrupt 8051 (20)

Recently uploaded (20)

8 interrupt 8051