Manual ssb

Operating manual

D432985XA
vers. 3.0

®

© 2006 SILCA S.p.A - Vittorio Veneto

This manual has been drawn up by SILCA S.p.A.

All rights reserved. No part of this publication may be reproduced or used in any form or by any means (photocopying,
microfilm or other) without the written permission of SILCA S.p.A.

Published: March 2007

Printed in Vittorio Veneto
by SILCA S.p.A.
via Podgora, 20 (Z.I.)
31029 VITTORIO VENETO (TV) – Italy

IMPORTANT NOTE: in compliance with current regulations relating to industrial property, we hereby state that the
trade-marks or trade names mentioned in our documentation are the exclusive property of authorized
manufacturers of locks and users.
Said trade-marks or trade names are nominated only for the purposes of information so that any lock for which our
keys are made can be rapidly identified.

INDEX
1 MACHINE DESCRIPTION ........................................................................................................ 2
1.1 MAIN CHARACTERISTICS ................................................................................................... 2
1.2 TECHNICAL DATA ................................................................................................................ 3
1.3 WORKING PARTS ................................................................................................................. 4
1.4 SYMBOLS ............................................................................................................................. 5
2 TRANSPORT ............................................................................................................................6
2.1 PACKING ............................................................................................................................... 6
2.2 UNPACKING ......................................................................................................................... 6
2.3 HANDLING ............................................................................................................................ 6
3 ACCESSORIES PROVIDED .....................................................................................................7
4 INSTALLATION AND PREPARATION ....................................................................................7
4.1 PREPARATION FOR USE - INITIAL OPERATIONS ............................................................ 7
4.2 CHECKING FOR DAMAGE ................................................................................................... 7
4.3 ENVIRONMENTAL CONDITIONS ........................................................................................ 7
4.4 SOFTWARE UPDATING ....................................................................................................... 7
5 REGULATION AND GAUGING ................................................................................................7
6 USING THE MACHINE .............................................................................................................8
6.1 START-UP ............................................................................................................................. 8
6.2 PASSWORD .......................................................................................................................... 8
6.2.1 PASSWORD (MEMORIZED) ................................................................................................... 9
6.3 MAIN MENU .......................................................................................................................... 9
6.4 IMMOBILIZER MENU / REMOTE CONTROLS .................................................................... 9
6.4.1 SELECTING THE CAR MAKE ............................................................................................... 10
6.4.2 CAR MODEL NOT ENABLE .................................................................................................. 10
6.4.3 CAR MODEL ENABLED ........................................................................................................ 10
6.4.4 COMMUNICATION PROCEDURE WITH THE IMMOBILIZER .............................................. 11
6.5 PIN CODE SERVICE ........................................................................................................... 11
6.5.1 VAG PIN CODE ...................................................................................................................... 11
6.5.1.1 DISABLED VEHICLE MODEL ................................................................................................. 11
6.5.1.2 ENABLED VEHICLE MODEL .................................................................................................. 11
6.5.1.3 COMMUNICATION PROCEDURE FOR PIN CODE READING ............................................. 12
6.5.2 VAG 7-4 PIN CONV. .............................................................................................................. 12
6.5.2.1 PIN 7 ........................................................................................................................................ 12
6.5.2.2 DEALER .................................................................................................................................. 13
6.5.2.3 IMPORTER .............................................................................................................................. 13
6.5.2.4 PIN 4 ........................................................................................................................................ 13
6.5.3 HYUNDAI® / KIA® PIN CODE ................................................................................................. 14
6.6 SETUP ................................................................................................................................. 15
6.6.1 ENABLING ............................................................................................................................. 15
6.6.2 LANGUAGE ........................................................................................................................... 18
6.6.3 SERIAL NUMBER .................................................................................................................. 18
6.6.4 CLOCK ................................................................................................................................... 18
6.6.5 VERSION ............................................................................................................................... 18
6.6.6 MEMORIZE PASSWORD ...................................................................................................... 19
6.6.7 KEYS REFERENCES ............................................................................................................ 19
6.7 ARCHIVE ............................................................................................................................. 19
6.7.1 SEARCH ................................................................................................................................ 19
6.7.2 PRINTOUT ............................................................................................................................. 20
6.7.3 ARCHIVE ERASE .................................................................................................................. 21
6.8 TEST .................................................................................................................................... 21
6.8.1 KEYBOARD ........................................................................................................................... 21
6.8.2 TEXT ...................................................................................................................................... 21
6.8.3 GRAPHICS ............................................................................................................................. 21
6.8.4 UPDATE SWITCH CAN ......................................................................................................... 22

7 MODEL CHANGE ....................................................................................................................23
8 WARNING/ERROR MESSAGES ............................................................................................24
9 HELP MENU ............................................................................................................................31
10 MAINTENANCE ......................................................................................................................33
10.1 CHECKING WIRING ........................................................................................................... 33
11 WASTE DISPOSAL ................................................................................................................34
12 ASSISTANCE ..........................................................................................................................35
12.1 HOW TO REQUEST SERVICE ........................................................................................... 35

Operating Manual - English SBB

GENERAL
The device is designed to the principles of European CE Directives.
The materials used in its manufacture are not dangerous and their use complies with directives. Its design
features make the machine and all its components completely safe to use.

FURTHER RISKS
There are no further risks arising from the use of the machine.

PROTECTION AND SAFETY PRECAUTIONS FOR THE OPERATOR
The operations for which the machine has been designed are easily carried out at no risk to the operator.

SAFETY REGULATIONS
To operate under conditions of maximum safety do not use the device without reading and understanding
clearly the contents of this operating manual.
• Check the electrical wiring periodically; if the wires are worn they should be repaired or replaced.
• Never work with wet, greasy or oily hands.
• Disconnect the device from the mains when it is not in use or in order to carry out maintenance work.
• Never tug at the power supply wire; make sure it does not come into contact with oil, sharp edges or heat.
• It is dangerous to use the device in areas at risk (damp or wet).
• Always work in a well lighted area.
• Keep the work area clean and remove all tools before turning on the machine.
• All visitors, children in particular, must keep at a safe distance and not touch the machine or electrical wiring.
• Do not use the device for purposes different from those described in the Operating Manual.
POWER SUPPLY
The machine is supplied with electricity at 12 Vdc provided by the vehicle battery, or as an alternative can
be powered from a 15 Vdc universal feeder supplied with the machine.

TURNS ON
The machine turns on automatically when the connection (OBD II or Optional) is connected to the diagnostics
socket or one of the feeder wires supplied with the machine is used.

IDENTIFICATION OF THE SBB DEVICE
The device has an identification plate showing its serial number (fig. 1).

SILCA SPA
VIA PODGORA 20
®
manufacturer’s TREVISO - ITALY
Tel. 0438-9136
address Fax 04138-913800
e-mail info@silca.it

TIPO type of machine
TYPE

N° MATRICOLA serial No.
working SERIAL No.
voltage
V HZ W A absorbed current
CE mark
MADE IN ITALY
year of working absorbed
manufacture frequency power

Fig. 1

(*) see chap. 11 "WASTE DISPOSAL", page 34.

Copyright Silca 2006 1

SBB Operating Manual - English

1 MACHINE DESCRIPTION
The machine is used to easily programme keys with transponders in the centralized immobilizer units of a
number of car models. In particular, it can:
- memorize all the keys in the centralized immobilizer unit;
- erase keys already in the memory;
- read the immobilizer ID code – IMMO ID (if applicable);
- read the mechanical code for the key (if applicable);
- add one or more keys;
- read the number of keys in the memory (if applicable);
- read any errors/anomalies in the centralized immobilizer unit;
- erase/zero any errors found;
- provide help;
- Memorize the remote controls.
The machine is provided with a password to prevent unauthorized use. Users have at their disposal a
functions menu to meet all possible requirements during operation.
NOTE: Once the machine is connected to the power mains it’s automatically switched on. To turn
it off exit from function and unplug the machine from the mains.

1.1 MAIN CHARACTERISTICS
OPERATING METHODS
- Adds or deletes keys and remote controls from the immobilizer control unit by connecting SBB to the vehicle
diagnostics input.
SPECIAL FUNCTIONS
- Storage in the User Data Archive of all operations carried out;
- Multi-language program;
- Machine test;
- Read the PIN CODE (where possible);
- Help (operational help for: type and position of connectors, procedures, keys, types of transponders, etc...).

PASSWORD
A principle password is needed to enable SBB (required every time the program is turned on), issued by
the supplier/distributor by means of a special "USE AGREEMENT FORM".

SBB - FULL LOADED CONFIGURATION
BASIC SOFTWARE
ACURA®, ALFA ROMEO®, AUDI®, BUICK®, CADILLAC®, CHEVROLET®, CHRYSLER®, CHRYSLER® CAN,
CITROËN®, DODGE®, DODGE® CAN, EAGLE®, FIAT®, FIAT®-PSA, FORD®, FORD® AUSTRALIA, FORD® USA,
GENERAL MOTORS® BRAZIL, HOLDEN®, HONDA®, HONDA® USA, HYUNDAI®, JAGUAR®, JEEP®, JEEP® CAN,
KIA®, LANCIA®, LAND ROVER®, LEXUS®, LINCOLN®, MAZDA®, MERCURY®, MITSUBISHI®, MITSUBISHI®
AUSTRALIA, MITSUBISHI® GREEK, MITSUBISHI® USA, NISSAN ®, NISSAN® JAPAN, NISSAN® TRUCKS, NISSAN®
USA, OLDSMOBILE®, OPEL® CAN BUS, PEUGEOT®, PONTIAC®, RENAULT®, RENAULT® CAN BUS, ROVER®,
SEAT®, SKODA®, SUBARU®, SUZUKI®, TOYOTA®, VOLKSWAGEN®, VOLKSWAGEN® BRAZIL, SPECIAL FUNCTION
ZZ-FNT 01, SPECIAL FUNCTION ZZ-FNT 02, SPECIAL FUNCTION ZZ-FNT 03, SPECIAL FUNCTION ZZ-FNT 04.
- These makes are all enabled for use.

SOFTWARE UPDATE (NEW MAKES RELEASED)
- To use the new makes loaded with the SW update (after purchase) you may proceed in two different
ways:

ENABLING BY PASSWORD ENABLING BY TOKEN

Enter a different password specific to Use a credit that is reduced every time
each new make released (see Ch. key programming/deletion is carried out.
“Enabling”) then you can always use the Credits can be purchased and loaded
device for that given make. onto SBB by means of a smart card (see
Apply for the passwords on the special chap. 6.6.1 "ENABLING" ).
form "USE AGREEMENT SHEET“
included in the software update kit.

2 Copyright Silca 2006


SBB - PAY PER USE CONFIGURATION
BASIC SOFTWARE
ACURA®, ALFA ROMEO®, AUDI®, BUICK®, CADILLAC®, CHEVROLET®, CHRYSLER®, CHRYSLER® CAN,
CITROËN®, DODGE®, DODGE® CAN, EAGLE®, FIAT®, FIAT®-PSA, FORD®, FORD® AUSTRALIA, FORD® USA,
GENERAL MOTORS® BRAZIL, HOLDEN®, HONDA®, HONDA® USA, HYUNDAI®, JAGUAR®, JEEP®, JEEP® CAN,
KIA®, LANCIA®, LAND ROVER®, LEXUS®, LINCOLN®, MAZDA®, MERCURY®, MITSUBISHI®, MITSUBISHI®
AUSTRALIA, MITSUBISHI® GREEK, MITSUBISHI® USA, NISSAN ®, NISSAN® JAPAN, NISSAN® TRUCKS, NISSAN®
USA, OLDSMOBILE®, OPEL® CAN BUS, PEUGEOT®, PONTIAC®, RENAULT®, RENAULT® CAN BUS, ROVER®,
SEAT®, SKODA®, SUBARU®, SUZUKI®, TOYOTA®, VOLKSWAGEN®, VOLKSWAGEN® BRAZIL, SPECIAL FUNCTION
ZZ-FNT 01, SPECIAL FUNCTION ZZ-FNT 02, SPECIAL FUNCTION ZZ-FNT 03, SPECIAL FUNCTION ZZ-FNT 04.
- Two different methods are available for using the new makes:

ENABLING BY MODEL CHANGE ENABLING BY TOKEN

By using an optional SMART CARD Use a credit that is reduced every time
“MODEL CHANGE” it is possible to key programming/deletion is carried out.
enable all the makes to use the basic
Software. Credits can be purchased and loaded
The card must be purchased and the onto SBB by means of a SMART CARD
enablings have to be downloaded in (see chap. 6.6.1 "ENABLING").
SBB by means of a SMART CARD (see
chap. 7 "MODEL CHANGE").

SOFTWARE UPDATE (NEW MAKES RELEASED)
To use the new makes downloaded with the SW update (after purchase) proceed only as follows:

ENABLING BY TOKEN

Use a credit that is reduced every time
key programming/deletion is carried out.
Credits can be purchased and loaded
onto SBB by means of a smart card (see
chapter “Enabling”).

SOFTWARE UPDATE
The machine can be updated through an RS232 serial line connection with a personal computer.

POWER SUPPLY
- From the car through an OBD II connector;
- From the car through the cigarette lighter plug;
- From the mains through a universal feeder and special cable.

1.2 TECHNICAL DATA
POWER SUPPLY
- 8-45 Volt (typically 12Volt from the vehicle diagnostic inlet or cigarette lighter plug).
- Universal feeder:

INPUT OUTPUT
Tension 90-264 Vac 15 Vdc
Current 1.0Arms @ 90V 1A
Frequency 47-63 Hz
Power 15 W

DIMENSIONS
Length: 220 mm
Width: 165 mm
Height: 50 mm
Weight: 300 g.



1.3 WORKING PARTS

A

B

C D E

Fig. 2

A - Retro illuminated LCD graphic display
B - 23-key keypad (numerical, functions, arrows, ESC, ENTER)
C - Parallel Port (25 Poles) to communicate with the vehicle
D - Serial Port RS232 (9 Poles) use only for Serial cable
E - Socket for cigarette lighter power cable or feeder

F - Standard OBD II cable

G - Cigarette lighter power
cable

H - Feeder

J - Serial cable



MAIN FEATURES
KEYPAD
The machine keypad allows the user to interact with it rapidly and easily. At any given time only the keys
involved in the cycle in progress are enabled.

HELP function keys

Left-Right arrow keys, move the cursor to the left or to the right

Up-Down arrow keys, move the cursor up or down

(ENTER) key confirms data entered or selection made

(ESC) key quits or returns to the previous screen/status

Fig. 3

LIQUID CRYSTAL DISPLAY
Retro illuminated LCD graphic display (128x64 pixel or 21x8 characters).

1.4 SYMBOLS
The box shows the machine screen and relative displays, as shown below:

- MAIN MENU -
1 - IMMOBILIZER
2 - REMOTE CONTROLS
> 3 - PIN CODE SERVICE
4 - SET UP
5 - DATA BASE
6 - TEST

Methods for selecting a specific function:
- Use the arrow Left/Right keys, the point where the cursor “>“shows the item required, then press ENTER;
- Digit a number (xx) from the keypad to access the item required directly from the menu.

- TEST -
1 - KEYBOARD
2 - TEXT
> 3 - GRAPHICAL
4 - UPDATE SWICH CAN

Example:
to access the GRAPHICS TEST menu (73) either use the arrows to select first the TEST menu (7), press
ENTER, then the GRAPHICS menu (3) and press ENTER, or digit (73) which corresponds to the GRAPHICS
TEST (73).



2 TRANSPORT
The machine and its components are easily transported by one person and its handling does not incur
any hazards.

2.1 PACKING
The packing ensures safe transport for the machine and protects all its parts.
To avoid knocks damaging the machine, we recommend using the original carrying case and packing
every time it is transported.

Fig. 4

2.2 UNPACKING
To remove the machine from its packing:

1) take care not to damage the box when opening as it can be used again (transfers, dispatch to the
manufacturer for repairs or maintenance).

2) check the contents of the packing case, which comprise:
- 1 carrying case;
- 1 machine;
- 1 universal feeder;
- 1 centralized unit connecting cable (universal), OBDII – 00 connector;
- 1 serial cable;
- 1 power supply cable with cigarette lighter plug;
- 1 set of documents: user’s manual, guarantee form and user’s agreement;
- 1 CD program

2.3 HANDLING
Always replace the machine in its carrying case after use.



3 ACCESSORIES PROVIDED
The device comes complete with:
- universal feeder;
- centralized unit connection cable (OBD II-00 connector);
- serial cable;
- power supply cable with cigarette lighter plug;
- CD program (to be used in the event of loss of the program on the machine).

4 INSTALLATION AND PREPARATION
Installation can be carried out by the purchaser and does not require special skills. The machine is
supplied ready for use – however, some checks and preparation are necessary before use.

4.1 PREPARATION FOR USE - INITIAL OPERATIONS
- power the machine by means of the supply socket (E);
-check that the serial number stamped on the device is the same as the one shown on the display; enter
the password (to enable use) (see chap. 6.2 "PASSWORD", page 8);
- select the language;

4.2 CHECKING FOR DAMAGE
The device will not normally damage if transport, unpacking and installation have all been carried out
according to the instructions in this manual; however it is always advisable to check that the machine has not
suffered any damage.
Should faulty operation arise that is not connected with the above-mentioned conditions, please contact After-
Sales Service.

4.3 ENVIRONMENTAL CONDITIONS
To ensure that the best use is made of the machine and that the keys with transponders produced work
properly, it is important to bear in mind operating conditions and temperature.
Given the characteristics of the transponders on the keys, in order to memorize them, THE
TEMPERATURE MUST BE ABOVE 5° C.
Ideal working conditions for the machine are therefore:
- temperature: from 5° to 40° C.

4.4 SOFTWARE UPDATING
The machine software can be updated by connection to a personal computer.
ATTENTION:the RS232 socket for connection to the PC is located on the front, near the display.
Use the RS232 serial cable provided and follow the instructions for updating.

5 REGULATION AND GAUGING
The machine is designed not to require any gauging or regulation.



6 USING THE MACHINE
This chapter describes all the operations required to memorize, erase, or add keys to the centralized
immobilizer unit by connecting SBB to the vehicle diagnostics input.

6.1 START-UP
When the machine is turned on the display shows the logo:

®

After a few seconds the following message appears:

S.N. : XXXXXXXXXXXXX

Ver. (SW): XXX.XX.XXX
Ver. (DB): XX.XX
Update : XXXXXXX
(F1) to continue

The wording “Update: XXXXXXX” give the level of updating for the program and database.
The wording “Ver (SW) XX.XX.XX” indicates the software version.
The wording “Ver (DB) XX.XX.XX” indicates the make and model Database version on the machine.
The wording “S.N.: XXXXXXXXXXXXX” give the machine serial number.
Check that the serial number shown on the display is the same as that on the document "USER’S
AGREEMENT" and on the label attached to the back of the machine.
Press F1 to continue.

6.2 PASSWORD
When selection has been made, the following message appears:

INSERT PASSWORD:
XXXXXXXX

To use the machine enter the password issued by the supplier/dealer, comprising 8 numerical characters.
- enter the password and press ENTER.

CORRECT PASSWORD
If the password is correct, the message below appears:

RIGHT PASSWORD

After a few seconds the program enters the main menu.



WRONG PASSWORD
If a wrong password has been entered, a beep advises the user and the display shows:

WRONG PASSWORD
INSERT PASSWORD:
XXXXXXXX

- Repeat the operation and press ENTER.

6.2.1 PASSWORD (MEMORIZED)
If the password has already been memorized on the machine (chap. 6.6.6 "MEMORIZE PASSWORD", page
19), when F1 is selected the following message appears:

PASSWORD SAVED

Wait a few seconds for the display to show the main menu.

6.3 MAIN MENU
There are two ways to choose the menu:

- MAIN MENU -
1 - IMMOBILIZER
2 - REMOTE CONTROLS
> 3 - PIN CODE SERVICE
4 - SET UP
5 - DATA BASE
6 - TEST

- Use the , arrow keys for selection then press ENTER, or digit the number corresponding to the
function.

6.4 IMMOBILIZER MENU / REMOTE CONTROLS
This function contains the database of vehicle makes / models / years for which the device is enabled and
can carry out the specific functions involved.
- Select “IMMOBILIZER/REMOTE CONTROLS”; from the MAIN MENU to view a list of car makes on the
display.

- MENU IMMOBILIZER -
AUDI
SEAT
SKODA
> VOLKSWAGEN
OPEL
FORD



SELECTING THE CAR MAKE
- Use the arrow keys to select the make, then press ENTER.
- Press ESC to quit.
After selecting the make the display will show the list of car models.

- VOLKSWAGEN -
BORA (98- )
CADDY (95-99)
CADDY (00- )
> GOLF (95-99)
GOLF (00- )
GOLF CABRIO (95-99)

FUNCTION F1
Press the “F1” key to show information relating to the make/model selected (type and position of connectors,
procedures, keys, types of transponder, etc.) (see chap. 9 "HELP MENU", page 31).

6.4.1 SELECTING THE CAR MAKE
SBB is not always able to automatically recognize all the immobilizer central units and is therefore unable to
automatically choose the communication procedure to launch. It is therefore NECESSARY to select the right
MAKE MODEL ANY OTHER CHARACTERISTICS (Petrol, Diesel, red key system, etc.) to which
the specific communication procedure is associated.
For more information about the car model see the Functions Menu of the specific make.

6.4.2 CAR MODEL NOT ENABLE
If a car model that is not enabled is selected, a beep is heard and the display shows:

- VOLKSWAGEN -
Device not enabled
for this model.
Insert password from
menu ENABLE FLAGS
(41)

6.4.3 CAR MODEL ENABLED
If a car model that is enabled has been selected, the display shows:

Insert the key
and turn on
the console

- Press ENTER to continue.



6.4.4 COMMUNICATION PROCEDURE WITH THE IMMOBILIZER
The following message appears:

Please wait
connecting...

The communication procedure with the immobilizer starts; if the car model selected is correct and the
immobilizer is detected, the Functions menu by make appears, otherwise an error message is shown (see
chap. 8 "WARNING/ERROR MESSAGES", page 24).

6.5 PIN CODE SERVICE
This menu describes some of the functions required to obtain a PIN CODE (for certain vehicle models only)
without going to the dealer.
Select the item “PIN CODE SERVICE” and press ENTER.
The display will show:
- PIN CODE SERVICE -
VAG PIN CODE
VAG 7-4 PIN CONV.
> HYUNDAI PIN CODE
KIA PIN CODE

- Use the Down/Up arrow keys to select the specific model, then press ENTER.
Press ESC to quit.

6.5.1 VAG PIN CODE
This function can read the vehicle PIN CODE directly from the OBD-II socket (only for certain VAG models).
Select “PIN CODE SERVICE” from the main menu, then “VAG PIN CODE”.
The display will show:

6.5.1.1 DISABLED VEHICLE MODEL
If the function is not enabled a beep is heard and a message appears:
- VAG PIN CODE -
Device not enabled
for this model.
Insert password from
menu ENABLE FLAGS
(41)

6.5.1.2 ENABLED VEHICLE MODEL
If the function is enabled the following message appears:

Turn the ignition on!

Press any key...

- Turn the key to the ON position.
Press any key.



6.5.1.3 COMMUNICATION PROCEDURE FOR PIN CODE READING
The display shows:

Please wait
connecting...

The communication procedure starts with the vehicle control panel memory. Different screens may
appear, according to the type of control panel on the vehicle.

6.5.2 VAG - 7-4 PIN CONV.
This function is used to convert a 7-digit pin code (issued by the dealer) to a 4-digit pin code for use on
VOLKSWAGEN®, AUDI®, SEAT® and SKODA® vehicles.
- To activate the function select “PIN CODE SERVICE”, then “VAG PIN CODE”.
Press ENTER.

- VAG CONVERTER -
PIN 7
DEALER
IMPORTER
> PIN 4
DATE (XX/XX/XXXX)
EXIT

- To activate the function, select ENTER.
- Press ESC to exit.

6.5.2.1 PIN 7
This is a 7-digit code issued by the dealer.

How to apply for the code:
- Use the function “READ IMMO ID” in SBB to read the series number of the central unit.
- Provide the authorized dealer with the following data:
• Central unit series number
• Chassis number
• Copy of log book
• ID document for applicant

6.5.2.2 DEALER
This is the ID code for the authorized dealer (different from dealer to dealer) who issues the 7-digit code.
The code is included in the rubber stamp used by the dealer to validate work on the vehicle.

444 01234

CAR MAKE

DEALER
NAME
ADDRESS

The stamp shown above is often found in the vehicle maintenance booklet.
- To activate the function, select “DEALER” and press ENTER.



6.5.2.3 IMPORTER
This is the ID code for the country in which the 7-digit code is applied for (different from country to country).
The code is included in the rubber stamp used by the dealer to validate work on the vehicle.

444 01234

CAR MAKE

DEALER
NAME
ADDRESS

Table of currently known Importer Codes.

COUNTRYIMPORTER CODE
ITALIA - 264
ENGLAND - 210
ISRAEL - 730
USA - 444
CANADA - 999
SPAIN - 572
PORTUGAL - 261
RIUNION ISLAND - 387

- To activate the function, select “IMPORTER” and press ENTER.

6.5.2.4 PIN 4
This is the 4-digit code to enter as PIN CODE on the SBB during the “PROG.NEW KEYS” or “No. KEYS
MEM.” stages.
It is calculated by the device when the other codes are known: Code7, Dealer Code, Importer Code
and date of issue.

CALCULATION OF PIN 4
calculate the PIN 4 proceed as follows:
- Insert the day, month and year of issue of CODE 7
- To activate the function, select “DATE” and press ENTER.
- Insert the PIN 7, DEALER and importer CODE.
- o activate the function, select the figure to insert and press ENTER.
An asterisk will confirm that the figure has been entered.

- VAG CONVERTER -
PIN 7 *
DEALER
IMPORTER
> PIN 4
DATE (XX/XX/XXXX)
EXIT

- The PIN 4 will appear automatically once all the data have been entered (DATA, PIN 7, DEALER,
IMPORTER).

ADVANCED OPTIONS
The function can also be used for inverse calculation.

Example:
If you have the correct data for:
- The date of issued of CODE;
- 3 of the 4 codes required;
The missing CODE can be found. Just insert the 3 items of known data and the missing figure will appear
automatically.



6.5.3 HYUNDAI® / KIA® PIN CODE
This function is used to calculate the 6-digit PIN CODE by means of the vehicle’s VIN number; in this way it
is not necessary to ask the dealer for this security code, which is essential for programming new keys.

NOTE: this function can only be used to obtain the PIN CODE for HYUNDAI® and KIA® relating to
SYSTEM 2 immobilizers.
For further information about Immobilizer systems and HYUNDAI® and KIA® PIN CODES, consult the
Operating manual for the specific make.

- To activate the function select “PIN CODE SERVICE” then “HYUNDAI® PIN CODE” or “KIA® PIN
CODE”.
- Press ENTER.
- The display will show:

- HYUNDAI/KIA PIN CODE -

Insert the last 6
digit of VIN:
123456

- Insert the last 6 digits of the VIN and press ENTER.

LEGEND: V.I.N. (Vehicle Identification Number) is the vehicle frame number.
This is usually found in the vehicle logbook or stamped on a metal plate located inside the bonnet.

- Insert the PIN CODE.

- HYUNDAI/KIA PIN CODE -

PIN CODE: XXXXXX

Press any key...

- Press any key to return to the “PIN CODE SERVICE” menu.



6.6 SETUP
This section contains the various setting menus for the machine.
Select "SETUP" from the main menu and press ENTER.

- SETUP -
> 1 - ENABLE FLAGS
2 - LANGUAGE
3 - SERIAL NUMBER
4 - CALENDAR/CLOCK
5 - RELEASE
6 - STORE PASSWORD
7 - KEYS REFERENCES

- Select and press ENTER.

6.6.1 ENABLING
After selection the display will show:

- ENABLING -
> 1 - IMMOBILIZER
2 - REMOTE CONTROLS
3 - TOKEN (X)

- Select IMMOBILIZER to view the vehicle makes available for entering enabling in the “Immobilizer” function;
- Select REMOTE CONTROLS to view the vehicle makes available for entering enabling in the “Remote
Controls” function;
- Select TOKEN to view the tokens available; further tokens can be loaded.

ENABLING MAKES (FUNCTION AVAILABLE ONLY FOR SBB FULL LOAD DEVICES)
After selecting the menu “IMMOBILIZER or REMOTE CONTROLS” the display will show:

- ENABLING -
> AUDI
FORD
NISSAN
OPEL
SEAT

Select the required make to view the enabling levels available and those already enabled.

- ENABLING MAKE -
LEVEL1 (*)
LEVEL2 (*)
> LEVEL3 (*)

To enter the enabling password applied for with the document provided with the software update disk
(software application FORM).
- Select the level of enabling and press ENTER.
- Select ESC to quit.
NOTE: the levels marked (*) are already enabled for operation.



PASSWORD ENTRY
After selecting the enabling level the display will show:

ENABLING MAKES
Insert Password
for activation
LEVEL X

XXXXXX

- Enter the password comprising 6 numerical characters.
- Press ENTER to continue, ESC to quit.

WRONG PASSWORD
If the Password entered is wrong the user is warned by a beep and the display will show:

PASSWORD
ABILITATION GROUP
CAR BRAND
WRONG

- Repeat the operation.
ATTENTION:only 3 attempts are allowed, after which the device is blocked. To release disconnect the device
from the power supply, then re-connect.

RIGHT PASSWORD
If the Password entered is right, the display will show:

ABILITATION GROUP
CAR BRAND
ENABLED

From this moment the device is enabled to operate at the enabling level selected.

ENABLING TOKEN
After selecting the “TOKEN” menu the display will show:

- ENABLING TOKEN -
TOKEN AVAILABLE
XX
Date of last loading
YY/YY/YYYY

XX = Tokens still available
YY/YY/YYYY = Date of last loading of tokens
F5 = Function key for unloading tokens from the smart card



LOADING TOKENS
To load new TOKENS onto the machine you must buy a Smart Card containing the credits.
Insert the Smart Card into the SBB before turning on the device (see fig. 5).

Fig. 5

Press the F5 function key
If credits have been transferred from the smart card to SBB successfully, the display will show:

- TOKEN FROM SMARTCARD -

OPERATION
SUCCESSFULLY
COMPLETED!

Press any key...

Press any key to return to the previous menu.
If the credits have not been successfully transferred from the SMART CARD to SBB, the display will show one
of the following errors:

ERROR
ERROR MESSAGE ON DISPLAY CAUSE/SOLUTION
NUMBER
SMART CARD. COMMUNICATION The card has not been inserted
1 ERROR. properly, or is damaged
CHECK INSERTION POSTION
SMART CARD. TYPE MISMATCH Try updating the device with the
latest version available and if this
2
does not work, return the card to
Silca as it may be damaged
SMART CARD. ALREADY USED The card has already been used
3
and cannot be re-used
SMART CARD. VERSION Try updating the device with the
MISMATCH. FIRMWARE UPDATE latest version available and if this
4 REQUIRED. does not work, return the card to
Silca as it may be damaged
SMART CARD. WRONG TOKEN The card is damaged, return to
8 NUMBER Silca
- Press any key to return to the previous menu.
- Check that the smart card has been inserted properly and repeat the procedure.



6.6.2 LANGUAGE
This function is used to select the language for the device.
- Select the item “LANGUAGE” from the “Setup” menu, the display will show:

- LANGUAGE -
> 1 - ITALIANO
2 - DEUTSCH
3 - FRANCAIS
4 - ENGLISH
5 - ESPANOL
6 - GREEK
7 - PORTUGUÊS

- Select the language and press ENTER

6.6.3 SERIAL NUMBER
This function is used to view the serial number of the machine.
- Select the item “SERIAL NUMBER” from the “Setup” menu; the display will show:

SBB
SERIAL NUMBER
XXXXXXXXXXXXX

6.6.4 CLOCK
This function is used to read the machine’s internal clock.
- Select the item “CLOCK” the “Setup” menu; the display will show:

- CALENDAR/CLOCK -

TIME:
XX:XX:XX
DATE:
XX/XX/XXXX

- Select ENTER to continue.
- Follow the instructions given by the device.
- The user is not enabled to the TIME/DATE changing functions of the clock.

6.6.5 VERSION
This function is used to view the FIRMWARE / SW / DATABASE version on the device.
- Select the item “VERSION” from the “Setup” menu:

- SBB -

Ver. (SW): XXX.XX.XXX
Ver. (DB): XX.XX
Release : XXXXXXX



- Ver. (SW): version of the internal program
- Ver. (DB): version of the car makes-models database
- Update: database update level given by the manufacturer’s code.

6.6.6 MEMORIZE PASSWORD
This option can be used to bypass the password, which is required every time the machine is turned on.
- Select the item “MEMORIZE PASSWORD” from the “Setup” menu, the display will show:

- MEMORIZE PASSWORD -

>YES
NO


6.6.7 KEYS REFERENCES
This option can be used to view the Silca or Ilco keys references on HELP F1 menu.
- Select the item “KEYS REFERENCES” from the “Setup” menu; the display will show:

- KEYS REFERENCES -
Select the
reference
to display
>SILCA
ILCO


6.7 ARCHIVE
This section contains all the controls for searching, printing, or deleting user data stored in the device
memory.
Select “ARCHIVE” from the MAIN MENU and press ENTER; the display will show:

- DATA BASE -
1 - SEARCH
2 - PRINT DATA
3 - ARCHIVE RESET

6.7.1 SEARCH
This control is used to make a search for:
- POS.: Position in which the operation carried out was saved
- DATE: date on which the operation was memorized
- MAKE: car make
- MODEL: car model
- SURNAME: customer’s surname
- NUMBER PLATE: car number plate



Select “SEARCH” from the “ARCHIVE”; menu; the display will show:

- SEARCH -
POS.: XX
DATE: XXXXXXXX
> BRAND: XXXXXXXXXX
MODEL: XXXXXXXXXX
SURNAME: XXXXXXXXXX
REG.NO.: XXXXXXXXXX

- Use the , , arrow keys to place the cursor in the required field and press .
- Enter the characters to be searched for.
- Press ENTER to proceed the search.

SEARCH METHOD
(POS.) (DATE)
- Digit a number or the date and press ENTER: the display will show the corresponding record.
- Use the key to view the previous record, the key to view the next record.

(MAKE) (MODEL) (SURNAME) (NUMBER PLATE)
- Digit the initial or part of the text to be searched for and press ENTER: the display will show the first
record available in order of position (POS.)
- Use the key to view the previous record, the key to view the next record.
If none of the search criteria are met or there are no data in the archive, the display will show:

NO INFORMATION
RECOVERED

- Press any key and repeat the search.

USER DATA
User data that meet the criteria are shown as follows:

USER DATA (0)
DATE: 20/03/2001
BRAND: AUDI
MODEL: A4
YEAR: (95-98)
SURNAME: ROSSI
NAME: MARIO

REG.NO.: TV9988776
KEYS: 3
PIN: 4567
IMMO ID: (F1)
Use the keys to view the user data in sequence (depending on the search selected).
- Press key F1 to view the IMMO ID.

6.7.2 PRINTOUT
At present this function is not active.



6.7.3 ARCHIVE ERASE
This function is used to erase all user data in the archive.
- Select “ERASE ARCHIVE” from the “ARCHIVE” menu; the display will show:

- ARCHIVE ERASE -

>NO
YES


6.8 TEST
This section contains all the controls with which to carry out a rapid operational test on the machine. Select
“TEST” from the main menu.The display will show:

- TEST -
1 - KEYBOARD
> 2 - TEXT
3 - GRAPHICAL
4 - UDPADE SWITCH CAN

6.8.1 KEYBOARD
This function is used to test the operation of all the keys on the device keypad.
- Select “KEYPAD” from the "TEST" menu.
- To carry out the test press all the keys on the device, one after the other; to quit press any key three
times.
TEST RESULT:
- TEST PASSED (all the keys are working properly)
- TEST FAILED (not all the keys has been pressed) possible causes:
- One or more keys not working properly
- The same key has been pressed for three times in a row.

6.8.2 TEXT
This function is used to test the operation of the display in the Text mode.
- Select “TEXT” from the “TEST” menu.

0123456789abcdefghijk

- Check that the characters on the display correspond.
- Press a key to quit.

6.8.3 GRAPHICS
This function is used to test operation of the display in the GRAPHICS mode.
- Select “GRAPHICS” from the “TEST” menu and check that all the pixel on the display are illuminated.
- Press a key to quit.



6.8.4 UPDATE SWITCH CAN
This function is used for manual updating of the internal software for the CAN BUS SWITCH.
- Select "UPDATE CAN BUS SWITCH" from the “TEST” menu.

OPTIMIZATION IN
PROGRESS

Updating of the SWITCH CAN BUS start now.
When updating is complete the SBB re-starts automatically.



7 MODEL CHANGE
Use the SMART CARD “MODEL CHANGE” (optional) to enable the software for a given machine. To do
so, insert the SMART CARD “MODEL CHANGE” into the SBB device before turning it on (see fig. 6).

Fig. 6

- Turn on the machine.

ENABLING COMPLETE
If enabling has been carried out successfully the machine starts normally and keys and remote controls
can be programmed for the enabled makes without using TOKENS.

ENABLING NOT COMPLETE
If errors have occurred during enabling the display will show one of the following errors:

ERROR
ERROR MESSAGE ON DISPLAY CAUSE/SOLUTION
NUMBER
SMART CARD. TYPE MISMATCH Try updating the device with the latest
version available and if this does not
2 work, return the card to Silca as it may
be damaged.
SMART CARD. ALREADY USED The card has already been used and
3 cannot be re-used
SMART CARD. VERSION Try updating the device with the latest
MISMATCH. FIRMWARE UPDATE version available and if this does not
4 REQUIRED. work, return the card to Silca as it may
be damaged.
SMART CARD. DEVICE MISMATCH. Try updating the device with the latest
FIRMWARE UPDATE REQUIRED. version available and if this does not
5 work, return the card to Silca as it may
be damaged.
SMART CARD. SERIAL NUMBER Check that the device serial
MISMATCH number corresponds to that
6 printed on the face of the card.
If there is an error, return the card
to Silca.
SMART CARD. WRONG FLAGS The card is damaged, return it to
7 VECTOR Silca.

- Press any key to return to the previous menu.
- Check that the SMART CARD has been inserted properly and repeat the procedure.



8 WARNING/ERROR MESSAGES
ERROR MESSAGE 1

- COMMUNICATION ERROR -

ECU
disconnected

Press ESC to quit

ERROR MESSAGE N° 2

Communication error

Press any key...

- These error messages may appear during communication with the immobilizer if the connection is cut
off, or in the case of physical disconnection between the device and immobilizer: disconnect the device
from the socket and repeat the operation.

ERROR MESSAGE 3

Not recognized
protocol

Press any key...

- This message appears when a car model is selected but none of the queries from the different protocols
used receive a coherent reply from the immobilizer. Check that you have selected the right makemodel.

ERROR MESSAGE 4

NOT VALID
PIN

- This message appears when the PIN CODE entered is not properly composed or is not recognized by
the immobilizer.



ERROR MESSAGE 5

Key not programmed
Repeat procedure

Press any key...

This message appears when key programming is not successful. Repeat the procedure.

ERROR MESSAGE 6

REMOTE CONTROL
not programmed
Repeat procedure

Press any key...

This message appears when remote control programming is not successful. Repeat the procedure.

ERROR MESSAGE 7

- PROG.NEW KEYS -

KEY i
Acquisition failed
Key faulty
Repeat procedure

Press any key...

- The key to be programmed is faulty, replace with a new key and repeat programming.
- Press any key to continue.

- PROG.NEW KEYS -

Procedure interrupted
Keys memorized before
procedure started are
enabled

Press any key...

- All the keys memorized before programming started are still enabled for operation.



ERROR MESSAGE 8

- PROG. NEW KEYS -

KEY i
Acquisition failed
Key faulty
Repeat procedure

Press any key...

- The key to be programmed is a wrong key, replace with the right key and repeat programming.

- PROG. NEW KEYS -

enabled.

Press any key...

- All the keys memorized before programming started are still enabled for operation.

ERROR MESSAGE 9

- PROG. NEW KEYS -

KEY i
Acquisition failed
Disabled key
Repeat procedure

Press any key...

- The key to be programmed has been erased and cannot be re-programmed. Replace with a new key and
repeat programming.
- Press any key to continue

- PROG. NEW KEYS -

enabled.

Press any key...

- All keys memorized before programming started are still enabled for operation.



ERROR MESSAGE 10

- PROG. NEW KEYS -

KEY i
Acquisition failed
Key already acquired
Repeat procedure

Press any key...

- The key to be programmed has already been programmed; repeat programming.

- PROG. NEW KEYS -

enabled
.
Press any key...


ERROR MESSAGE 11

- PROG. NEW KEYS -

KEY i
Acquisition failed
Key not present or
without transponder
Repeat procedure
Press any key...

- The key to be programmed is without a transponder. Replace with a new key with transponder and repeat
programming.

- PROG. NEW KEYS -

enabled.

Press any key...




ERROR MESSAGE 12

- PROG. NEW KEYS -

Key memorization failed

EEPROM memory error

Press any key...

- There is an internal anomaly in the immobilizer.

ERROR MESSAGE 13

- PROG. NEW KEYS -

Body Computer
not properly
programmed

Press any key...

- There is an internal anomaly in the body computer.

ERROR MESSAGE 14

- RKE PROGRAM -

Procedure failed

Press any key...

- The remote control to be programmed is not the right one, or is broken, or errors have occurred during
programming. Make sure the remote control is the right one and efficient, then repeat programming.

ERROR MESSAGE 15

- PROG. NEW KEYS -
Error found:
XXXX
Eliminate the error
before programming keys
and/or remote controls

Press any key...

- If errors are found in the immobilizer, programming cannot take place.
- Delete the errors using the “DELETE ERRORS” function, then repeat programming.



ERROR MESSAGE 16

- PROG. NEW KEYS -

Body Computer
not properly
programmed

Press any key...

- The Body computer (main control unit) is not properly programmed; programming operations cannot be
carried out.
- Have the body computer properly programmed by an authorized dealer, then proceed with programming.

ERROR MESSAGE 17

- RKE PROGRAM -

REMOTE CONTROL N° XX
Learning failed
Detective rem.control
Repeat the procedure

Press any key...

The remote control to be programmed is not the right one or is faulty.
- Repeat programming, making sure that the remote control is the right one and operational.

ERROR MESSAGE 18

- RKE PROGRAM -

Learning failed
Run-down battery

Press any key...

The battery in the remote control to be programmed is flat.
- Replace the remote control battery with a new one and repeat programming.

ERROR MESSAGE 19

- RKE PROGRAM -

Learning failed
Rem.ctrl alr. acquired

Press any key...

The remote control to be programmed is already in the memory and operational.
- Use a remote control not yet programmed and repeat programming.



ERROR MESSAGE 20

- RKE PROGRAM -

Learning failed


Press any key...

Some errors have occurred during programming.
Repeat programming, making sure that the remote control to be programmed is the right one and operational,
and that the immobilizer system has no operational anomalies (use the reading errors function).
Press any key to continue.



9 HELP MENU
This function is enabled after the selection of car make and model.
The following help functions are available:

F1
Press the function key “F1” to read information relating to the MAKE/MODEL selected:
- MAKE
- MODEL
- YEAR
- REFERENCE (SILCA)
- ORIGINAL TRANSPONDER
- MEMORIZATION PROCEDURE
- MAX. NUMBER OF KEYS THAT CAN BE MEMORIZED
- CONNECTOR TO USE
- ADAPTER TO USE
- CONNECTOR POSITION

Example:

- CAR MAKE -
A2: (95-96)
CONNECT: 00
Pos.Con.: (F3-F4)
KEY REF: HU66AT6
Orig.Tr: MEG/CR
RW2/RW3 ID: 48
F2-F3-F4
N.KEY: 8
Self P.: (F2)

- Connect: type of cable to use to connect with the immobilizer (see ID label on the cable);
- Pos.Con: position on the vehicle of the diagnostics socket to which the device can be connected; press F3
– F4 to access the information.
- Key Ref.: Silca key to use for the car model selected
- Orig.Tr.: type of transponder used on the original key
- RW2/RW3 ID: ID code for transponder used by RW2/RW3.
- No. Key: max. number of keys that can be memorized on the vehicle (when the maximum number of keys
is reached, a key must be erased from the memory in order to memorize a new one).
- Self P.: description of the direct programming procedure.

NOTE: correspondence of the original transponder to the Silca key to be used should be checked
with the RW2/RW3 for the type of transponder.
The F2-F3-F4 help menus are now available (see last bottom line).

F2
Direct programming is a memorization/deletion method for new keys on the vehicle which does not require
diagnostics. The procedure is active on certain models only, as its use depends on the policy of the car
manufacturer.

Press the “F2” function key; the display will show the direct programming procedure:

- CAR MAKE -
ON BOARD PROGRAM A
1 - Programming new
keys without use of
programmed keys



F3-F4
Press the “F3” function key, the display will show the position of the connector (Graphic Image)

Fig. 7


Press the “F4” function key, the display will show a description of the position of the connector:

- POSITION -
Remove the cover
situated at the side
of the hand brake




10 MAINTENANCE
ATTENTION:for repairs or replacement of parts for maintenance, the ‘CE’ mark is guaranteed only if original
spare parts provided by the manufacturer are used.

The machine does not require special maintenance.

ATTENTION:do not open the machine for any reason whatsoever)

Before starting any type of maintenance (checks or replacement of parts) read the following instructions:
- Do not carry out any maintenance operations with the machine turned on;
- Always disconnect from the mains;
- Follow the instructions in the manual;
- Use original spare parts.

FAULT PROBABLE CAUSE
A) CHECK POWER SUPPLY CONFIGURATION

DISPLAY: B) CHECK CONNECTION WIRING
- DISPLAY IS BLANK WITH MACHINE ON - REPLACE DISPLAY (AFTER-SALES SERVICE)
- REPLACE ELECTRONIC CONTROL BOARD (AFTER-SALES
SERVICE)
KEYPAD: A) CHECK CONNECTION WIRING
- NOT RESPONDING TO CONTROLS - REPLACE KEYPAD (AFTER-SALES SERVICE)

A) CHECK THAT THE RIGHT CAR MODEL HAS BEEN
NO COMMUNICATION WITH THE
SELECTED
CENTRALIZED UNIT B) CHECK THE WIRING

The instructions above relating to the probable causes of the faults described should be considered indicative
and not a complete list of the possible causes of malfunctions.
Contact the After-Sales Service in the event of any other problems arising.

10.1 CHECKING WIRING
If it is necessary to check the machine’s internal wiring, proceed as follows:
- Disconnect the supply wire;
- Detach any other wires connected to the machine;
- Remove the 4 screws located on the back of the machine;
- Remove the cover carefully, paying attention to the wiring;
- Check that all the connectors are properly in place.



11 WASTE DISPOSAL
EU regulations establish special arrangements for the disposal of waste (*).

WASTE DERIVING FROM THE MACHINE
The machine produces no waste during its use.

MACHINE
The machine is made of re-usable materials. Re-cycling is recommended ecological practice.

PACKING
The machine is consigned in a cardboard packing box which can be re-used if undamaged. When it is to
be thrown away it is classified as solid urban waste and it should be placed in the special paper collecting
bins.

(*) Waste is any substance or object deriving from human activity or natural cycles, thrown away or to be thrown away.

DISPOSING OF THE BATTERY
The battery (fig. 8) must be disposed of according to current regulations.

Fig. 8

INFORMATION FOR USERS
as per art. 10 of Directive 2002/96/CE of 27/01/2003
regarding waste from electric and electronic appliances (RAEE),

• The symbol illustrated above, also found on the machine, indicates that it has been placed on the market and
must be included in separate rubbish collection when the user wishes to dispose of it (including all
components, sub-assemblies and consumables that are integrated in the product).
• For information about the collection system for such appliances please contact SILCA S.p.A. or another
subject registered in the various National Rolls for other countries in the European Union. Household waste
(or of similar origin) can be included in the separate collection system for urban waste.
• On purchasing a new appliance of equivalent type, the old one can be consigned to the dealer. The dealer
will then contact whoever is responsible for collecting the appliance.
• Suitable separate collection of the unused appliance and its dispatch for treatment, recovery and
environmentally compatible disposal, makes it possible to avoid potential negative effects on the environment
and human health, and aids recycling and the recovery of the materials used.
• Unauthorised disposal of the product by users involves the application of the sanctions provided for in
received Directives 91/156/CE and 91/689/CE.



12 ASSISTANCE
Silca provides full assistance to purchasers of the machine. To ensure complete safety for the operator, any
job not specified in this manual should be carried out by the manufacturer or in the special Service Centres
recommended by Silca.
On the back cover of this manual there is a list of the Service Centres and relative addresses.

12.1 HOW TO REQUEST SERVICE
The guarantee attached to the machine ensures free repairs or replacements of faulty parts within 12 months
of purchase. All other service calls must be arranged by the customer with Silca or with a Silca service centre.


Silca S.p.A.
Vittorio Veneto

VITTORIO VENETO 21/06/2006

CE DECLARATION OF MACHINE COMPLIANCE

SILCA S.p.A. - VIA PODGORA 20 ( Z.I.)
31029 VITTORIO VENETO (TV) - (ITALY)
TEL. 0438 9136 - FAX. 0438 913800
Declares under its own responsibility that the Universal Diagnostic Device model

SBB

complies with the requirements of the following European Directives:

European Union DIRECTIVE 2004/108/CE (Electromagnetic Compatibility)
and with the EN 61326-1 Standards

General Manager Basic Production Center

SILCA S.p.A.
Via Podgora, 20 (Z.I.)
31029 VITTORIO VENETO (TV)
Tel.: 0438 9136
Telefax: 0438 913800 P. IVA COD. FISC. E REG. IMPR. 03286730266
www.silca.it REA TV 258111 - CAP. SOC. € 10.000.000 i.v. - EXPORT TV 038851 A Member of the Kaba Group

SILCA S.p.A.
Via Podgora, 20 (Z.I.)
31029 VITTORIO VENETO (TV)
Tel. 0438 9136 Fax 0438 913800
www.silca.it

In the United Kingdom
SILCA Ltd.
Kimpton Road - Sutton
SURREY SM3 9QP
Tel. 0208 6416515
Fax 0208 6441181
E-mail: sales@silcaltd.co.uk

In Germany
SILCA GmbH
Siemensstrasse, 33
42551 VELBERT
Tel. 02051 2710
Fax 02051 271172
E-mail: info@silca.de

In France
SILCA S.A.
78440 PORCHEVILLE
Tel. 01 30983500
Fax 01 30983501
E-mail: info@silca.fr

In Spain
SILCA KEY SYSTEMS S.A.
C/Santander 73A
BARCELONA - SPAIN
Tel. 0034 934981400
Fax 0034 932788004
E-mail: silca@silca.es

Members of the Kaba Group

Manual ssb

More Related Content

What's hot (17)

Similar to Manual ssb (20)

Manual ssb