Welding of pipelines

WELDING PRESSURE
PIPELINES &
PIPING SYSTEMS

Procedures and Techniques

Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Vertical Down vs. Vertical Up . . . . . . . . . . . . . . . . . . . . .3-4

Cross Country Pipeline-Vertical Down Welding
Joint Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Pipe End Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Welding the Root Pass . . . . . . . . . . . . . . . . . . . . . .5-6
Current Settings w/Lincoln Engine Driven Welders .6-7
Root Pass Welding . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Root Pass Troubleshooting . . . . . . . . . . . . . . . . . . . . .7
Techniques for Welding Hot Pass . . . . . . . . . . . . . . . .8
Techniques for Welding Fill and Cap . . . . . . . . . . . . . .8
Setting the Current etc. . . . . . . . . . . . . . . . . . . . . . .8-9
Preventing Cracking . . . . . . . . . . . . . . . . . . . . . . . . .10
Techniques for X60 etc. . . . . . . . . . . . . . . . . . . . .10-11
Vertical Down Procedures . . . . . . . . . . . . . . . . . .12-13
Electrode Consumption . . . . . . . . . . . . . . . . . . . .14-15
Thin Wall Pipe Welding Procedures . . . . . . . . . . .16-20
Double Ending . . . . . . . . . . . . . . . . . . . . . . . . . .20-21
Flux & Electrode Selection . . . . . . . . . . . . . . . . . . . .21

API Pipe Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24

Consumables for Welding Pipe . . . . . . . . . . . . . . . . . . . .25
Consumables for High Strength Pipe . . . . . . . . . . . .26
Consumables for SMAW . . . . . . . . . . . . . . . . . . .27-30
Consumables for FCAW . . . . . . . . . . . . . . . . . . . . . .30
Consumables for GMAW . . . . . . . . . . . . . . . . . . . . .31

Pipe Welding Electrodes . . . . . . . . . . . . . . . . . . . . . .32-33
Mechanical Properties . . . . . . . . . . . . . . . . . . . . .34-35

In-Plant Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-37
Pipe Axis - Horizontal & Vertical . . . . . . . . . . . . . . . .38
Vertical Up Welding . . . . . . . . . . . . . . . . . . . . . . . . .39
Vertical Up Electrode Consumption . . . . . . . . . . .40-41
ASTM Pipe Steels . . . . . . . . . . . . . . . . . . . . . . . .42-43

-2-

Introduction
This booklet is a guide to welding pipe with Shielded Metal Arc
Welding (SMAW) and double ending pipe using automatic welding.
Lincoln Electric supplies electrodes, power sources, automatic and
semiautomatic wire feeders, submerged arc wire and flux, which are
the industry standards for pipeline construction around the world.
Semiautomatic, self-shielded flux-cored Innershield® Process is
being used around the world to produce high quality, low hydrogen,
reliable, lower cost pipeline welds.

Vertical Down vs. Vertical Up Welding
Vertical down welding with cellulosic electrodes is normally done with
high currents and high travel speeds. Cellulosic electrodes have a
thin coating containing a large amount of organic cellulose. When the
electrode is burned, the coating forms a protective gas coating for
the molten metal. Because of the organic material and the moisture
content of these electrodes, they have a very strong arc force but at
the same time the weld metal freezes very quickly. This method of
welding is fast and economical, consequently most cross country
pipelines are welded with the progression vertically downward.
Impact toughness properties, which are very good may be met with
modern cellulosic electrodes.

Vertical up welding with either cellulosic electrodes or low hydrogen
electrodes is done with relatively low currents and low travel speed,
which produce joints with relatively few, but large beads.

-3-

With low hydrogen vertical up electrodes, welds may be made virtu-
ally free of slag entrapment and porosity. These welds are best able
to meet strict radiographic requirements for high pressure, high tem-
perature or low temperature piping. Because of the low hydrogen
deposit,
susceptible to

CROSS COUNTRY PIPELINE
Vertical Down Welding
Joint Preparation
The joint preparation usually used for cross country pipeline is from
API 1104 code. As shown in the figure below, the normal situation is
a “penny land, penny gap”, meaning that the land (root face) on the
pipe should be ground to approximately the thickness of a penny
[1/16” (1.6mm)]. The gap between pipes should be the same dis-
tance, if possible. A 60° Included angle is used.

+5
30° – 0

Bevel

Land
T
1/16"

Gap 1/16"

Pipe End Cleaning
Pipe rarely will be received in a condition suitable for welding.
Generally, there will either be an oil or rust coating, or a coating to
prevent corrosion. This could include paint, primer, varnish, epoxy, tar
paper, or any variety of organic substances, all of which are undesir-
able for welding. Cleanliness is critical to prevent defects leading
to rejected welds and costly repair, so these coatings must
always be removed.

-4-

hydrogen cracking.
these electrodes have an advantage for high strength pipes

The following are the guidelines to minimize welding defects related
to surface contamination:

• Moisture and condensation must always be removed prior to
welding.
• Both pipe ends must be cleaned, on the inside and the out-
side, at least 1” (25mm) beyond the edge of the bevel.
• One recommended means of cleaning pipe is with a straight
shaft grinder with a rubber expanding wheel and carbide
coated sleeve. A sanding disc can also be effective, as well
as an abrasive grinding disc.
• Depending on the pipe size, a half round file can be used to
remove any burrs created when the land is ground on to the
end of the pipe.

Welding the Root Pass
Before beginning to weld the pipe, the procedure should be checked
to assure that the correct electrode is being used. This includes the
diameter and the classification of the electrode. The welding con-
sumable should be selected to correctly match (or overmatch) the
strength of the pipe.
Either Fleetweld® 5P or Fleetweld 5P+ should be used for stringer
bead and the hot pass when the hardness of the root pass is a con-
cern, even if other higher strength consumables are to be used to fill
and cap the weld. This “softer” root increases the resistance to cer-
tain types of weld cracking.
A number of factors will determine how many welders will be needed
to weld the root pass. In any case, it is best to have welders either
(1) weld opposite one another or (2) evenly spaced around the pipe.
This will minimize the amount of distortion in the pipe and prevent the
gap from opening or closing. If possible, it is also desirable not to fin-
ish a weld in exactly the bottom of the pipe because the tie-in can be
more difficult. Similarly, it is best to avoid starting at exactly the top of
the pipe (12 o’clock position).
As a rule of thumb, for a 5/32” (4.0mm) electrode, on the welding
time for one electrode should be approximately one minute and the
length of weld should be approximately the same as the length of
electrode consumed. This would produce a travel speed of approxi-
mately 12 inches per minute, but this is extremely sensitive to joint
preparation and exact welding conditions.
The root pass is welded with a “drag” technique. The tip of the electrode
is held in contact with both pipes and dragged around the circumfer-
ence of the pipe, progressing vertically downhard. The electrode ini-
tially should be held roughly perpendicular to the pipe. If there is a
proper fit-up and the proper current is used, a small “keyhole” will be

-5-

seen following behind the electrode. If the keyhole is not seen, the
electrode is not penetrating through to the inside of the pipe. The
remedies for this would be:
• Higher current.
• Apply more pressure on the electrode which lowers voltage and
yields a colder puddle (depending on the type of welding machine).
• Use a push angle (although this is not always advisable).
• Slower travel speed.
If the keyhole becomes too large and difficult to control, the remedies
would be:
• Lower the current.
• Travel faster until the size of the keyhole decreases.
• Use more of a drag angle while using faster travel speed until the
keyhole becomes more manageable.
• Apply less pressure on the electrode which creates a bigger key-
hole.
The required current decreases as the gap size increases. If the gap
is too narrow, it is not unusual to push so hard on the electrode that
a 5/32” (4.0mm) electrode will bend.
Sometimes, because of magnetic conditions the arc will tend to push
to one side of the joint. This is called arc blow. There are two solu-
tions to this while welding:
1) Put side pressure on the electrode opposing the arc
blowing tendency. This will cause the coating to burn
more even, and equalize the burnoff and tie-in equally.
2) While continuing to weld, point the electrode to counter-act
the arc blow. This is the less desirable method
because it can lead to internal undercut defects.

Current Setting with Lincoln Engine Driven Welders
The following recommendations are based on the following assump-
tions:
• Welding is done in the vertical down (5G or 6G) position.
• The root pass is made with a 5/32” (4.0mm) diameter electrode.
• A cellulosic electrode (E-XX10) is being used.
• The root pass is welded with reverse (DC+) polarity.
• The hot pass is made with a 5/32” (4.0mm) diameter electrode.
• The fill pass is made with a larger diameter 3/16” (5.0mm) elec-
trode.
• The joint has been carefully prepared to API specifications (1/16”
land, 1/16” gap and 60° included angle.

The joint fit-up will rarely be perfect, so the following recommenda-

-6-

tions should be used ONLY as a starting point. The welder’s skill and
the characteristics of their machine and the joint conditions will all
contribute to variations from the recommended set points. The set-
tings given on page 8 are intended only as starting points.
For root passpolarity. Inthe current control should be set as high as
everse (DC+) welding, International
necessary while the open circuit voltage (OCV) is set as low as possi-
ble, while still permitting the electrode without sticking. In practice, it
often used. Negative melts arc to strike
is not obvious by looking at the dials on the machine how to accom-
plish this.

Root Pass Welding
Welder Range Control Setting Fine Control Setting
Current Range Selector Fine Current Adjustment
Pipeliner® 200G
Classic II 240-160 ~30
Classic 300G (or)
Classic 300D 190-120 40
SA-250
Variable Voltage Control Current Control
5 100 - 150
Job Selector Current Control
SAE-400 Lower end of
~150
Overhead & Vertical Section
Process & Range Selector Output Control
Commander™ 300
250 Max. 6-7
Commander 500

In each case listed above, with the proper fit-up, the current with a
5/32” (4mm) diameter electrode will be in the neighborhood of 130
amps. From this point, the current should be changed according to
the individual welder’s skill and needs.In the United States, root pass
welding is usually done with r
locations straight polarity (DC-) is
faster then positive therefore travel speed should be faster and inter-
nal undercut and hollow bead defects are less likely. DC- (straight)
polarity is also advisable for thin wall pipe to prevent burn through.

Root Pass Troubleshooting

To Reduce High/
These Effects Current Gap Land Low Bevel Polarity
Wagon Tracks Decrease Increase Decrease Decrease Increase Erratic
Internal Undercut Decrease Decrease Increase Decrease Decrease DC-
Lack of Fusion Decrease Increase Decrease Decrease Increase DC+
Cracking Decrease Erratic Decrease Decrease Increase DC-
Hollow Bead Decrease Increase Decrease Decrease Increase DC-

-7-

Techniques for Welding Hot Passes
After the root pass is welded, the root bead is generally very convex
on the exterior of the pipe. The normal procedure is to grind the root
pass to eliminate the excessive convexity. Normally, the entire weld is
not ground out, rather only enough to expose “wagon tracks”. These
are lines of slag that are on either side of the built up convex region.
The purpose of the hot pass is primarily to burn out the “wagon
tracks”. Ideally, this is achieved leaving the joint free of undercut and
some filling of the joint is also accomplished. To do this, a high
current is normally used. With 5/32” (4.0mm) cellulosic electrodes, a
current of 160 - 200 amps is normally used, but using higher current
values, the electrode can overheat. Larger (3/16” diameter) elec-
trodes can also be used, with currents around 180 amps. Larger
electrodes have a tendency to fill rather than dig.
Techniques for Welding Fill and Cap Passes
The exact procedure for welding fill and cap passes is dependent on
the characteristics of the pipe (wall thickness, temperature, and posi-
tion on the pipe), the skill of the welder, as well as the characteristics
of the welding machine. With SMAW stick electrodes, the idea is nor-
mally to fill the joint as quickly as possible. When welding vertically
down, higher currents may be used than vertical up welding, so the
melting rate of the electrode is greater and the joint can be filled in
less time. Additionally, the usual practice is to use a larger diameter
electrode for the fill passes than what had been used for the root and
hot passes [3/16” (5.0mm) electrode when 5/32” (4.0mm) electrodes
were used for the root and hot passes].
In critical applications for low temperature service, it may be neces-
sary to maximize the impact toughness properties of a weld. In this
case, one technique is to split the layers into 2 passes as soon as
possible. The objective is to align fine-grained reheated zones along
the centerline of the weld, where the test samples are taken. Fill
passes should continue until the joint is filled to flush or slightly below
flush with the pipe. If the beveled edges of the joint are visible, the
cap pass(es) can be welded more easily.
The cap pass should be welded at lower currents than the fill passes
[as low as 140 amps with a 3/16” (5.0mm) electrode].
Setting the Current for Hot Pass, Fill Pass, “Stripper Pass” and
Cap Pass Welding
The purpose for the hot pass is to melt and float out the wagon
tracks left after the root pass. The current, therefore, should be high
enough to burn out the slag, but not so high as to burn a hole
through the root pass.
The root pass should be thoroughly cleaned before welding the hot
pass. This is typically done with a disc grinder, which not only cleans

-8-

out the slag, but also flattens the contour of the bead before the hot
pass is welded. If this grinding operation is not done, there is a
greater chance that wagon track slag entrapment will occur.
The hot pass should be started as soon as possible after completely
finishing the root pass, always within five minutes.
The typical current for a hot pass ranges from 160 to 200 amps with
either 5/32” (4.0mm) or 3/16” (5.0mm) electrodes. The welding travel
speed increases with increasing current, as does the ability to clean
out wagon tracks. The risk of burning through, especially on the top
and the bottom of the pipe also increases and the usable length of
electrode decreases. With high current, the electrode may overheat
and catch fire. At this point, even if a long stub remains, welding
should stop and the electrode should be thrown away.
With low current, there is little risk of burning through, but welding
progresses slower and more care must be taken to assure that the
wagon tracks are eliminated.
For the passes after the root pass, the tap setting is generally not
adjusted. The current should be adjusted by adjusting the fine con-
trol. Typically this is done with a remote control.
With the SAE-400, the left tap (Job Selector) should be increased to
run the hot pass. Using the Commander 300, the hot pass might be
run with the 230 max tap and the control increased to 7 or 8.
Fill passes are usually run with 3/16” (4.8mm) or 5.0mm electrodes.
Depending on the wall thickness, interpass temperature, etc., the
current could be between 160 and 200 amps, which may not require
changing the machine setting from the hot pass.
A slight side-to-side weave should be used when welding a fill pass.
This allows the bead to wet-in properly with the side walls and helps
fill the groove.
The current used on stripper passes depends on which diameter of
electrode is to be used. The purpose of a stripper pass is to fill the
joint up to flush. Instead of high travel speeds, lower currents may be
used.
Before welding the cap pass, the concave portions of the weld
should be welded up to flush with stripper passes, commonly
required only in the 2 to 5 o’clock positions. Either 5/32” (4.0 mm) or
3/16” (5.0 mm) diameter electrodes can be used.

-9-

Cap passes are frequently run with lower currents than the fill passes.
With 150 amps and a 3/16” (5.0mm) diameter electrode, it is possi-
ble to put in a uniform bead all the way around the pipe.
Preventing Cracking
Good welding practice is essential in preventing weld cracking, which
includes preheating when needed. The welding techniques described
in this book will minimize the defects which could cause cracking.
Depositing the hot pass in a timely manner is helpful, as well as
depositing as large a root pass as possible.
The need for preheating varies considerably depending on the grade
of pipe steel. The tendency to crack increases with increasing pipe
strength, wall thickness, carbon and alloy content, as well as
decreasing ambient temperature. Welding low strength pipe in warm
weather, the need to preheat may not be required, (although recom-
mended for moisture removal). Thick wall, high strength pipe being
welded in cold weather may require up to 350°F (177°C) preheat.
Specific preheat requirements must be determined for each situation.
Techniques for Welding High Strength Pipe
(X-60, X-65, X-70 and X-80 Pipe)
These recommendations are suggested to help produce crack-free
welds with a minimum of defects on high strength pipe.
• Joint preparation and line-up must be carefully controlled. High-
low conditions should be held to a minimum.

• Thin walled [up to 3/8” (10mm)] X-80 pipe can be welded with
Shield-Arc® 90. Weld X-70 pipe with either Shield-Arc 80 or
Shield-Arc 70+. Pipes X-60 and X-65 pipes can be welded with
Fleetweld 5P+, Shield-Arc HYP, Shield-Arc HYP+,Shield-Arc 70+
or Shield-Arc 80.
• Preheat cold pipe to at least 70°F (21°C). The exact degree of pre-
heat depends on the pipe steel, but preheating up to 350°F
(177°C) would not be unreasonable for X-80 pipe.

-10-

• An internal fit-up clamp should not be removed until the entire root
pass is complete.
• Fewer defects will be seen if restarts and stops (craters) are
ground out, with the stops ground down to a feathered edge.
• Don’t start the root pass welds at exactly the top of the pipe (12
o’clock position) or end them at exactly the bottom (6 o’clock
position). Stopping the weld at the 6 o’clock position can con-
tribute to burnthrough, tie-in or suck-back problems.
• When finishing an electrode on the root pass, a fast pullout (flicking
the electrode) can reduce the size of the remaining keyhole, mak-
ing tie-in easier.
• Since reverse polarity (DC+) is commonly used by U.S. pipeline
operators for root pass welding, switch to straight polarity (DC-)
when burn through, internal undercut and hollow bead defects
persist. Polarity change is an essential variable in API 1104 code -
requiring a procedure qualification.
• Excessive travel speed in either the root or hot pass will cause
defects.
• Start and complete the hot pass immediately after completion of
the root pass.
• If the temperature of the pipe has dropped below the prescribed
interpass temperature, reheat the entire joint.

-11-

Vertical Down Procedures
(E6010, E7010, E8010 or E9010)
DC+
Currents up to 200 amps are often used on the hot and fill passes

3/16" Electrode Cap Pass, 3/16" Electrode
160-190 Amps 150-180 Amps

160-185 AMPS
125-165 AMPS T

5/32" Electrode
1/16"

but cause premature coating breakdown and large stub losses.

+5
Bevel 30° – 0

T Land
1/16"

Gap 1/16"

Use 1/8” (3.2 mm) diameter electrode for the stringer bead when the
gap is too small to permit use of the 5/32” (4.0 mm) size or where the
silicon level causes a larger than normal keyhole.
Stripper passes may be required in the 2 to 5 o’clock position.

Pipe Wall
Thickness No. of
Inches (mm) Passes
5/16 (7.9) 4
3/8 (9.5) 5
1/2 (12.7) 7

The number of passes may vary depending on the operator,
electrode diameter and procedure.

-12-

Alternate Vertical Down Stringer Bead Procedure
(E6010, E7010, E8010 or E9010)
DC-
60° Bevel

Land
1/16"
Gap 1/16"

Wall Diameter Current
Thickness Electrode Amps (DC-)
Up to 1/4” (6.4mm) 1/8” (3.2mm) 80-115
Over 1/4” (6.4mm) 5/32” (4.0mm) 90-140
Over 1/4” (6.4mm) 3/16”(1) (4.8mm) 140-165

(1) Root pass welding with 3/16” (4.8mm) diameter electrode requires more
operator skill. Pipe land and gap tolerances are more critical when using
3/16” (4.8mm) electrode for stringer bead applications. Lower consumable
cost is the primary advantage for 3/16” (4.8mm) diameter. Its use will not
provide any significant increase in arc speed over 5/32”(4.0mm) diameter.

-13-

Cross Country Pipe
Vertical Down Electrode Consumption

Wall Thickness

5/16” 3/8”

Electrode Required per Joint (lbs.) (1)
Pipe
Diameter 5/32” 3/16” Total 5/32” 3/16” Total
6 Inch .34 .54 .88 .34 .86 1.2
8 Inch .45 .71 1.2 .45 1.1 1.6
10 Inch .56 .88 1.4 .56 1.4 2.0
12 Inch .67 1.0 1.7 .67 1.7 2.4
14 Inch .73 1.1 1.8 .73 1.8 2.5
16 Inch .84 1.3 2.1 .84 2.1 2.9
18 Inch .94 1.5 2.4 .94 2.3 3.2
20 Inch 1.1 1.6 2.6 1.1 2.6 3.7
22 Inch 1.2 1.8 3.0 1.2 2.9 4.1
24 Inch 1.3 2.0 3.3 1.3 3.1 4.4
26 Inch 1.4 2.1 3.5 1.4 3.4 4.8
28 Inch 1.5 2.3 3.8 1.5 3.7 5.2
30 Inch 1.6 2.5 4.1 1.6 3.9 5.5
32 Inch 1.7 2.6 4.3 1.7 4.2 5.9
34 Inch 1.8 2.8 4.6 1.8 4.4 6.2
36 Inch 1.9 2.9 4.8 1.9 4.7 6.6
38 Inch 2.0 3.1 5.1 2.0 5.0 7.0
40 Inch 2.1 3.3 5.4 2.1 5.2 7.3
42 Inch — — — 2.2 5.5 7.7
44 Inch — — — 2.3 5.7 8.0
46 Inch — — — 2.4 6.0 8.4
48 Inch — — — 2.5 6.3 8.8

(1) Includes four inch stub lengths. These figures will vary with
different stub loss practices.

Quantities required for the 5/32” diameter will vary based on travel
speeds of the root pass and hot pass. Slow travel speeds may
increase these quantities by up to 50%.

-14-

Wall Thickness

1/2” 5/8” 3/4”


5/32” 3/16” Total 5/32” 3/16” Total 5/32” 3/16” Total

.45 2.2 2.7 — — — — — —
.56 2.7 3.3 — — — — — —
.67 3.2 3.9 — — — — — —
.73 3.5 4.2 .73 5.7 6.4 .73 8.3 9.0
.84 4.0 4.8 .84 6.5 7.3 .84 9.4 10.2
.94 4.5 5.4 .94 7.3 8.2 .94 10.6 11.5
1.1 5.0 6.1 1.1 8.1 9.2 1.1 11.8 12.9
1.2 5.5 6.7 1.2 8.9 10.1 1.2 13.0 14.2
1.3 6.0 7.3 1.3 9.7 11.0 1.3 14.2 15.5
1.4 6.5 7.9 1.4 10.5 11.9 1.4 15.3 16.7
1.5 7.0 8.5 1.5 11.3 12.8 1.5 16.5 18.0
1.6 7.5 9.1 1.6 12.1 13.6 1.6 17.7 19.3
1.7 8.0 9.7 1.7 13.0 14.7 1.7 18.9 20.6
1.8 8.6 10.3 1.8 13.8 15.6 1.8 20.1 21.9
1.9 9.1 11.0 1.9 14.6 16.5 1.9 21.3 23.2
2.0 9.6 11.6 2.0 15.4 17.4 2.0 22.4 24.4
2.1 10.1 12.2 2.1 16.2 18.3 2.1 23.6 25.7
2.2 10.6 12.8 2.2 17.0 19.2 2.2 24.8 27.0
2.3 11.1 13.4 2.3 17.8 20.1 2.3 26.0 28.3
2.4 11.6 14.0 2.4 18.6 21.0 2.4 27.2 29.6
2.5 12.1 14.6 2.5 19.4 21.9 2.5 28.3 30.8

-15-

Thin Wall Pipe Procedures
Vertical Down

1/8" EXX10 : 90-120 AMPS

3/32" EXX10 : 53-80 AMPS .156" and thinner

Polarity DC+

Fleetweld 5P+ is recommended. However, Fleetweld 5P, Shield-Arc
85 or Shield-Arc HYP+ can be used, providing the same diameter
electrode is used.

Vertical Down Electrode Consumption
Wall Thickness

.125”
Pipe Diameter 3/32” 1/8” Total

4 Inch .071 .092 .163
4-1/2 Inch .080 .102 .182
6 Inch .106 .138 .244
6-5/8 Inch .118 .152 .270
8 Inch .142 .184 .326
8-5/8 Inch .153 .198 .351
10 Inch .178 .230 .408
10-3/4 Inch .191 .247 .438
12-3/4 Inch .223 .289 .512
14 Inch .248 .323 .571
16 Inch .284 .369 .653
20 Inch .355 .461 .816
24 Inch — — —
28 Inch — — —
32 Inch — — —
36 Inch — — —

-16-

Butt Weld
1/8" EXX10 : 115-125 AMPS
OR
5/32" EXX10 : 115-130 AMPS
1/8" EXX10 : 95-130 AMPS

1/8" EXX10 : 90-120 AMPS .164" : 250
Polarity DC+
In some cases 5/32” (4.0 mm) diameter electrode may be used for
the
recommended. For root pass welding, see Alternate Vertical Down
Procedure on page 16.

Wall Thickness

.188” .250”
1/8” 5/32” Total 1/8” 5/32” Total

.196 .146 .342 .232 .177 .409
.221 .164 .385 .261 .199 .460
.294 .219 .513 .348 .268 .616
.325 .242 .567 .384 .293 .677
.392 .292 .684 .464 .354 .818
.422 .314 .736 .500 .382 .882
.490 .365 .855 .581 .442 1.023
.526 .392 .918 .623 .475 1.098
.615 .458 1.073 .727 .552 1.279
.686 .520 1.206 .812 .615 1.427
.784 .593 1.377 .929 .703 1.632
.980 .741 1.721 1.161 .879 2.040
1.177 .890 2.067 1.393 1.062 2.455
1.372 1.040 2.412 1.624 1.230 2.854
1.568 1.186 2.754 1.858 1.406 3.264
1.764 1.338 3.102 2.089 1.582 3.671
Quantities required for the smaller diameter electrode may vary by up
to 50%, based on size and travel speed of the root pass. Heavier
cap passes will increase total electrode requirements by up to 50%.

-17-

first pass on .250” wall material, although 1/8” (3.2 mm) is

Vertical Down - Bell & Spigot
Use a straight progression or short whipping technique. The latter is
better for poor fit up and also for controlling the puddle in the 5 to 7
o’clock position. Use one pass. If portions of the weld are shallow,
apply a second pass.

Electrode Consumption

Electrode Required per Joint
(lbs) (1)
Wall Thickness Pipe Diameter
Gauge Decimal Fraction 4” 4-1/2” 6” 6-3/8”

14 .075” 5/64” .041 .046 .062 .068
13 .090” 3/32” .053 .059 .078 .088
12 .105” 7/64” .078 .088 .114 .129
— .125” 1/8” .095 .107 .142 .157
10 .135” 9/64” .100 .113 .150 .166

-18-

Wall Pass Electrode & Diameter Current
Thickness No. (Inches) Range (DC+)

.075” 1 1/8 Fleetweld 5P+ 80-100
.090” 1 1/8 Fleetweld 5P+ 80-100
.105” 1 5/32 Fleetweld 5P+ 120-130
.125” 1 5/32 Fleetweld 5P+ 120-130
.135” 1 5/32 Fleetweld 5P+ 130-140

NOTE: Fleetweld 5P, Shield-Arc 85, Shield-Arc HYP or
Shield-Arc HYP+ may also be used.

Electrode Required per Joint (lbs) (1)

Pipe Diameter
8” 8-5/8” 10” 10-3/4” 12-3/4” 14” 16” 20”

.082 .088 .098 .108 .127 .136 .155 .194
.106 .114 .132 .142 .168 .185 .211 .264
.156 .168 .195 .209 .245 .271 .310 .387
.190 .205 .238 .253 .298 .330 .377 .471
.200 .215 .247 .264 .314 .345 .394 .494

-19-

Double Ending
Double ending is the automatic submerged arc welding of two
lengths of pipe into one longer length. It is practical where terrain
permits hauling the automatic welding stations and the double
lengths of pipe.
The automatic welding methods weld joints faster than is possible
with stick electrodes. This reduces welding costs, but, more
importantly, it increases the miles of pipe that can be laid each day.
Double ending also increases pipe laying speed because the
submerged arc process consistently makes high strength welds of
excellent X-ray quality. Few “cutouts” are required.
Along the Right of Way
Double ending along the right of way utilizes portable automatic
welding stations which are moved frequently as the line progresses. It
eliminates the need for hauling double lengths of pipe long distances.
Weld the root pass with stick electrode or semi-automatic processes
and the usual internal line-up clamps. To avoid cracking, the stringer
bead should have a minimum of 3/16” (4.8 mm) throat and, ideally,
the first automatic bead should be started immediately after comple-
tion of the stringer bead. The other beads are welded by rotating the
pipe beneath an automatic welding head.

-20-

Stationary Double Ending
The stationary double ending automatic welders work at pipe delivery
points. The double length pipe section are hauled to the pipeline for
laying. When appropriate, the automatic welders are moved to the
next pipe delivery station.
Both two and three station equipment is used. With three station
equipment, only the first pass is welded at the first station. The other
external beads are welded at the second station. With two station
equipment, all external beads are welded at the first station. The
internal bead is always welded at the final station.
NOTE: The Lincoln Electric Company strongly recommends for
weldments intended for sour gas, sour crude, or other critical service
applications that the customer verifies that both the level of hardness
and variation in hardness of the weld, heat affected zone, and base
plate are within acceptable limits.

Flux and Electrode Selection
steel and for higher impact strength on
Because of the high dilution characteristic of this type of welding, the
mechanical properties of the weld are highly dependent on the
chemistry of the pipe. All welding materials and procedures should
be tested on actual pipe steel under field conditions to determine
usability.
Flux
860 neutral flux is the most recommended flux, depending on job
requirements and welding conditions. 882 neutral flux may be used
on some lower carbon pipe
heavier wall thicknesses.
Electrodes
L-60 - Most popular choice with 860 flux. Lowest hardness. Preferred
for pipe intended to carry sour gas or sour crude.
L-61 - Intermediate hardness. Improved bead appearance over L-60.
L-50 - Highest hardness of mild steel electrodes. Improved bead
appearance over L-61. Improved impact strength vs. L-60 at -20°F
(-29°C) on pipe 3/4” (19 mm) wall thickness or greater.
LA-75 - Similar in hardness to L-50. Best bead appearance. Highest
impact strength at -50°F (-45°C) on wall thicknesses of approximately
3/4” (19mm) or greater. Deposits contain approximately 1% nickel.

-21-

860/L-60 will meet the minimum yield requirements and produce low
hardness and good impact strength at -20°F (-29°C) on X-42 through
X-60 pipe. 860/L-60 will also meet the minimum yield requirements
and produce low hardness and good impact strength on most X-65
and some X-70 pipe, depending on plate chemistry, wall thickness,
and procedures.
If strength is too low with L-60, it may be necessary to use L-61 or L-
50. On some pipe steels, L-61 or L-50 with 860 flux may be required
to meet minimum Charpy impact requirements. The weld matrix hard-
ness and tensile strength will be higher with L-61 or L-50 than with L-
60. With single arc double ending procedures, L-70 will not produce
higher impact strength than L-60 and will results in higher weld matrix
hardness.
Because of the large variations possible in pipe chemistry, all consum-
ables should be tested on actual pipe steel to verify that requirements
will be met.

API Pipe Steel
The following data is partial review of the 38th edition (May 1990) of
API specification 5L. For the latest specific details, obtain a copy of API
Standard 5L .
Definitions
The most common steel used for oil and gas cross country pipeline is
the API 5LX series. Meanings of these pipe designation are as follows:
5L Specification for line pipe.
X Grade designation for high strength line pipe.
The two numbers following the “X” are the first two digits of the mini-
mum yield strength. For example X-60 has a minimum yield strength of
60,000 psi (414 MPa).
Carbon and Manganese Content
When the pipe carbon and manganese content is near the maximum
allowed by the specifications, welding without cracking is difficult, par-
ticularly in cold weather. Therefore, pipe is commonly made using steel
of lower carbon and manganese content. High mechanical properties
are obtained by cold expanding the pipe.
When pipe analysis is near maximum, follow the techniques under
“Preventing Cracking” on page 10.

-22-

Chemical Requirements for Heat Analysis
Process of Manufacture: Electric furnace, open-hearth,
basic-oxygen or killed deoxidized basic-bessemer

Carbon Manganese Phosphorus Sulfur
Welded Grade Max. (%) Max. (%) Max. (%) Max. (%)

Non-
X-42 0.28 1.25 0.04 0.05
expanded
Non-
X-46, X-52 0.30 1.35 0.04 0.05
expanded
Cold-
X-42, X-46, 0.28 1.25 0.04 0.05
expanded
X-52

Non-
expanded X-56(1), X-60(1) 0.26 1.35 0.04 0.05
X-65(1) 0.26 1.40 0.04 0.05
(or)
X-70(1) 0.23 1.60 0.04 0.05
Cold-
X-80 0.18 1.80 0.03 0.018
expanded

(1) May also contain small amounts of columbium, vanadium or titanium.

High Silicon Pipe
Surface pinhole porosity may sometimes be encountered when weld-
ing 5LX pipe containing high silicon (up to 0.35%). Use currents in
the lower end of the current range or smaller diameter electrodes to
minimize this problem.
X-56, X-60, X-65, X-70 & X-80 Pipe
Since these pipe steels may have an analysis other than specified
see footnote (1), above, and there is no upper limit on strength, pipe
with a tensile strength of 100,000 psi (689 MPa), sometimes arrives
on the job. Making crack-free welds in this steel requires careful
attention to the “ Techniques for Welding High Strength Pipe”
discussed on page 10.

-23-

Preheat and interpass temperature control are recommended for
optimum mechanical properties, crack resistance and hardness
control. This is particularly important on multiple pass welds and
heavier plate. Job conditions, prevailing codes, high restraint, alloy
level and other considerations may also require preheat and interpass
temperature control.
NOTE: The Lincoln Electric Company strongly recommends for
weldments intended for sour gas, sour crude, or other critical service
applications that the customer verifies that both the level of hardness
and variation in hardness of the weld, heat affected zone, and base
plate are within acceptable limits.

Pipe Grades - Minimum Yield and Tensile Strengths

Pipe Minimum Yield Minimum Tensile
Grade psi MPa psi MPa

X-42 42,000 290 60,000 414
X-46 46,000 317 63,000 434
X-52 52,000 358 66,000 455
X-56 56,000 386 71,000 489
X-60 60,000 414 75,000 517
X-65 65,000 448 77,000 531
X-70 70,000 483 82,000 565
X-80 80,000 552 90,000(2) 620
(2) 120,000 maximum.

-24-

Consumables for Pipe Welding
Currently, there are four categories of consumables available for
welding pipes of various strength levels.
• SMAW (Shielded Metal Arc Welding)
Cellulosic Electrodes
Vertical Up, Low Hydrogen Electrodes
Vertical Down, Low Hydrogen Electrodes
• FCAW (Flux-Cored Arc Welding)
Self-Shielded (Innershield®) Electrodes
Gas-Shielded (Outershield®) Electrodes
• GMAW (Gas Metal Arc Welding)
Solid Wire Electrodes
Root Pass Welding with STT Power Supply
• SAW (Submerged Arc Welding)
Solid Wire Electrodes with Flux for Double Ending(1)

For any grade of pipe, there are possibilities for both process and
the consumable to be used. The table below gives various electrode
choices for different strength pipes. These are for fill and cap pass-
es. Lower strength electrodes commonly are used for root and hot
passes.

X-52 &
Electrode Under X-56 X-60 X-65 X-70 X-80
Fleetweld 5P ✓ ✓
Fleetweld 5P+ ✓ ✓ ✓ ✓
Shield-Arc HYP ✓ ✓ ✓ ✓
Shield-Arc HYP+ ✓ ✓ ✓ ✓
Shield-Arc 85 ✓ ✓ ✓ ✓
Shield-Arc 70+ ✓ ✓ ✓ ✓
Shield-Arc 80 ✓ ✓ ✓ ✓
Shield-Arc 90 ✓ ✓ ✓
Lincoln 16P ✓ ✓ ✓ ✓
Lincoln 18P ✓ ✓ ✓ ✓ ✓
Lincoln LH D-80 ✓ ✓ ✓ ✓
Lincoln LH D-90 ✓ ✓ ✓ ✓ ✓
Lincoln LH D-100 ✓ ✓ ✓ ✓ ✓
NR-207, 207-H ✓ ✓ ✓ ✓ ✓
NR-208-H ✓ ✓ ✓ ✓ ✓
SuperArc L-50 ✓ ✓ ✓ ✓
SuperArc L-56 ✓ ✓ ✓ ✓
SuperArc LA-75 ✓ ✓ ✓
SuperArc LA-90 ✓ ✓ ✓ ✓
SuperArc LA-100 ✓ ✓ ✓ ✓

-25-

Consumables for High Strength Pipe
The mechanical requirements of x-80 pipe are a yield strength of at
least 80,000 psi (551 MPa), minimum ultimate tensile strength of
90,000 psi (620 MPa), and a maximum ultimate tensile strength of
120,000 psi (827 MPa).
The mechanical property requirements of the weld are not as clearly
defined. API 1104 requires that when tested, with a transverse tensile
test, either:
(1) the weld metal exceeds the specified minimum tensile strength
of the pipe (with the root pass and cap pass reinforcement in
tact),
or
(2) the pipe material breaks first. Because the reinforcement is left
intact, the weld metal does not necessarily need to be as
strong as the pipe.
A level of ductility in the weld metal is required to pass a guided bend
test, but there are no explicit requirements for the tensile test.

Strength Requirements for Pipe Grades

Minimum Yield Minimum Tensile Maximum Ultimate
Pipe Strength Strength Tensile Strength
Grade psi MPa psi MPA psi MPa

X-42 42,000 289 60,000 413 — —
X-46 46,000 317 63,000 434 — —
X-52 52,000 358 66,000 455 — —
X-56 56,000 386 71,000 489 — —
X-60 60,000 413 75,000 517 — —
X-65 65,000 448 77,000 530 — —
X-70 70,000 482 82,000 565 — —
X-80 80,000 551 90,000 620 120,000 827

-26-

Lincoln Products for X-80 Pipe
The following is a list, by process, of Lincoln electrodes which will
meet the strength requirements for X-80 pipe.
SMAW
For a conventional, vertical up basic low hydrogen root pass, we
recommend Lincoln 16P. Our European subsidiaries also have
Conarc® 49 C and Kryo® 1 for root pass welding. None of these
meet the strength requirements for an X-80 pipe. Depending on the
procedure, undermatched root pass electrodes are used to take
advantage of the (generally) higher ductility. Overmatching electrodes
are then used for the fill and cap passes.
Lincoln 16P
Yield Strength 71,200 psi (491 MPa)
Tensile Strength 90,900 psi (627 MPa)
Elongation 22%
Hardness (Rb) 88
CVN at -20°F (-29°C) 48 ft. lbs. (65 Joules)
Fill and cap passes can be welded vertical up with Lincoln 18P to
meet the strength requirements. Jet-LH 8018-C3 MR generally meets
the specified criteria, however, the nickel content is approximately
1%,and can exceed the limit often imposed for sour service.
Lincoln 18P
Elongation 28%
Vertical down welding of X-80 pipe can be done with Lincoln LH-D90,
which meets E9018-G electrode classification. Some data taken from
a vertical down weld made on flattened X-80 pipe:
Lincoln LH-D90
Elongation 26%
Lincoln LH-D100
Elongation 24%

-27-

Vertical Down Procedures for LHD type
Electrodes
• To avoid starting porosity, the electrode angle should be maintained
perpendicular to the pipe when striking the arc.
• The electrode should be tapped against the pipe at the back end
(top) of the crater and held close to the pipe.
• As the hot start/pencil point melts away, maintain the electrode in
the same location with a very short arc. When the arc is stabilized,
advance the electrode.
• A short arc (1/8”) should be maintained, instead of dragging the
electrode. When the electrode is dragged, a convex bead will
result, especially on the bottom half of the pipe. With a short arc,
the bead will be flatter.
This electrode is not recommended for root pass welding. The elec-
trode does not penetrate sufficiently to accommodate even a small
degree of mismatch (high/low condition).
When a 60° included angle joint preparation is used, the normal
welding sequence would include two passes with a 1/8” (3.2 mm)
electrode. After that, one or two full weave layers would be made
with the 5/32” (4.0 mm) electrode. A split weave procedure would
normally be used after that.
Approximate currents for this electrode are 140 amps for the 1/8”
(3.2 mm) electrode, 170 amps for the 5/32” (4.0 mm) electrode, and
190 amps for the 3/16” (4.8 mm) electrode. Independent of what the
recommended current setting might be, the electrode works best
when run at the highest current possible without overheating. When
the optimum current is used, the electrode will glow orange immedi-
ately after stopping the arc, but not overheat or breakdown when a 3
inch stub remains.
A drag angle is normally used while welding vertically down. This
angle can be 30° at the 3 o’clock position, although the exact elec-
trode angle will depend on the current used and the ability of the pipe
to cool the weld pool.
On the bottom of a pipe, the electrode angle should tend towards
perpendicular to the pipe, and after the 5 o’clock position, a slight
push angle can be used. With a push angle on the bottom, the

-28-

tendency for convex bead shapes can be overcome. With a 10°
push angle and a small “horseshoe” weave, it is possible to maintain
a flat bead profile.
A limited amount of weaving can be used with LHD type electrodes.
As long as the preheat, interpass, and wall thickness conditions allow
it, a weave of up to one electrode diameter can reasonably be used.
Weaving wider than one electrode diameter can lead to slag
entrapment.

FACE BEND TOP OF PIPE
OR
SIDE BEND TENSILE SECTION
NICK BREAK
ROOT BEND
OR
SIDE BEND
OVER 4-1/2 TO
12-3/4 INC

ROOT BEND
OR
NICK BREAK SIDE BEND

TENSILE SECTION FACE BEND
OR
SIDE BEND

-29-

Lincoln Electric has a cellulosic electrode which meets the strength
level requirements of X-80 pipe. Although cellulosic electrodes are
not generally considered for this strength level, thin wall pipes have
been welded successfully with these products. Root and hot passes
on high strength pipe have been made with this electrode without
problems. Shield-Arc 90 has an E9010-G classification, which
carries with it the requirement of a 78,000 psi (538 MPa) minimum
yield strength and a 90,000 psi (620 MPa) minimum tensile strength.
Typical AWS test results for Shield-Arc 90 lists the following data for
the 3/16” (5.0 mm) diameter.
Shield-Arc 90
Elongation 26%

FCAW (Self-Shielded)
Innershield NR-208-H was redesigned recently to meet the strength
requirements of X-80 pipe. The typical results gave the following
properties.
NR-208-H
Elongation 27%
NR-208-H typically has a nickel content of approximately 0.85%. The
yield strength of NR-208-H can reach as high as 87,000 psi (600
MPa), and the tensile strength can reach as high as 100,000 psi
(684 MPa).

FCAW - Gas-Shielded
A gas-shielded, flux-cored electrode, which could conceivably be
used to weld an X-80 pipe would be Outershield 91K2-H. Typical
properties from an AWS plate.
Outershield 91K2-H
Elongation 27%
Gas mixture of 75% Argon/25% CO2 was used.

-30-

GMAW
There are two possibilities in the Lincoln Electric product line of meet-
ing the strength level requirements with GMAW electrode. LA-100 is
an ER100S-G electrode, whose typical properties on an AWS plate
using 98% Argon/2% Oxygen shielding gas are as follows.

LA-90
Elongation 27%
Hardness Rb 93

The manganese content of the deposited metal is over 1%, and the
nickel is in the range of 1.9%.

Another possibility to meet the strength requirement would be LA-90,
an ER80S-D2 and ER90S-D2 electrode. Depending on the shielding
gas used, the wire diameter, and the actual procedure, this electrode
would meet the strength requirement. Typical properties for this prod-
uct, taken from a test plate welded with 1/16” (1.6mm) diameter
electrode with 95% Argon/5% Oxygen shielding gas, are as follows:

LA-100
Elongation 21%
Hardness Rb 101

For root pass welding, either of these electrodes could be welded
with the Surface Tension Transfer™ (STT) power supply. Since this
power supply is used only for the root pass, no mechanical property
data is available. A CO2 shielding gas is standard for this low spatter,
low heat process.

Summary
Several alternatives are available for welding X-80 pipe, depending
on the exact requirements for a project; hydrogen levels, composi-
tional requirements (in particular, nickel), hardness, level of automa-
tion required, availability of machinery, degree of overmatch, and any
number of other factors may determine the suitability of one product
over another.

-31-

Pipe Welding
Recommended for Electrodes
Electrodes for Mild Steel Pipe
Fleetweld 5P ( E6010)
Basic out-of-position electrode. Used for welding ASTM and X-42
through X-52 mild steel pipe. Your best choice for dirty, rusty, or
painted pipe.
Fleetweld 5P+ (E6010)
Similar to Fleetweld 5P, with added advantages of quick striking,
easy slag removal and improved final appearance.
all position welding of pipe X-42 through X-52.
Shield-Arc 85 (E7010-A1)
Used for 1/2” Molybdenum pipe steels and X-42 through X-56 grade
pipes. Can be handled vertical up or vertical down.
Shield-Arc HYP+ (E7010-P1)
Designed to provide improved welding characteristics for vertical
down root, hot, fill or cap pass welding of API 5L pipe, grades X-52
through X-65 high strength pipe.
Shield-Arc HYP (E7010-G)
Specifically made for vertical down welding all passes on 5L or 5LX
pipe, grades X-52 through X-65. Features easy operation, minimum
wagon tracks and windows and almost no tendency for fill and cap
pass pinholes.
Shield-Arc 70+ (E8010-G)
Very good electrode for root, hot, fill and cap passes. Primarily for
vertical down, but can also be used for vertical up. Excellent wetting
on the cap pass, steady concentrated arc.
Shield-Arc 80 (E8010-G)
Similar welding characteristics and bead appearance to Shield-Arc
70+ with much better low temperature impact properties. Excellent
“stacking” ability, allowing slower travel speeds at high currents, thus
allowing faster filling of joints.
Shield-Arc 90 (E8010-G)
Specifically designed for X-80 pipe. Similar to Shield-Arc 80 with
higher strength. Can be used for root and hot passes, and for fill and
cap passes up to 3/8” (9.5mm) pipe. With proper precautions, thick-
er wall pipe may also be welded without cracking.
Low Hydrogen Electrodes for Pipe Welding
Lincoln 16P (E7016)
Specially designed for vertical up welding of pipe. The thin coating of
the 3/32” (2.4 mm) size allows for its use in root pass welding. Can

-32-

be used in grades X-52 through X-65. Because of its unique burn-off
characteristics, it is recommended for welding of open joint gaps.
Lincoln 18P (E8018G)
Low hydrogen electrode designed primarily for vertical-up fill and cap
pass welding of high strength pipelines, up to and including X-80
grade.

LH-D80, LH-D90 & LH-D100 (E8018-G, E9018-G & E10018-G)
These low hydrogen electrodes are designed for vertical down on
high strength pipe up to and including X-80. They have significantly
greater deposition rates than downhill cellulosic electrodes.
Jet-LH 8018-C3 MR (E8018-C3)
Produces a 1% nickel deposit for welding low temperature alloy pipe
that require good notch toughness down to -60°F (51°C).
Jet-LH 8018-C1 MR (E8018-C1)
Capable of producing a 2-1/4% nickel deposit with notch toughness
of 20 ft-lbs at -75°F (-59°C) for welding pipe for liquid ammonia,
propane and other gases.
Jetweld LH-90 MR (E8018-B2)
Produces 1-1/4% chromium, 1/2% molybdenum deposit commonly
required for high temperature, high pressure pipe.
Jetweld LH-100M1 MR (MIL-10018-M1)
Yield strength levels of 82-110,000 psi (565-758 MPa). Excellent
notch toughness down to -60°F (-51°C).
Jetweld LH-110M MR (E11018-M)
Tensile strength levels of 110-128,000 psi (758-882 MPa).
Jet-LH 8018-B2 MR (E8018-B2)
Capable of producing a 1-1/4% chromium, 1% molybdenum deposit
when design temperatures exceed 850°F (454°C).
Jet-LH 9018-B3 MR (E9018-B3)
Capable of producing a 2-1/4% chromium, 1% molybdenum deposit
when design temperatures exceed 850°F (454°C).

-33-

Mechanical Properties
Welded and tested in accordance with appropriate
AWS or MIl specifications.
As-Welded
AWS Tensile Strength Yield Strength
Electrode Class psi (MPa) psi (MPa)

Fleetweld 5P E6010 60-76,000 (414-524) 48-65,000 (331-448)
Fleetweld 5P+ E6010 60-86,000 (414-593) 48-76,000 (331-524)
Shield-Arc 85 E7010-A1 70-78,000 (483-538) 57-71,000 (393-489)
Shield-Arc HYP E7010-G 70-86,000 (483-593) 60-74,000 (414-512)
Shield-Arc HYP+ E7010-P1 77-86,000 (531-593) 63-71,400 (439-482)
Shield-Arc 80 E8010-G 80-94,000 (552-648) 67-83,000 (462-572)
Shield-Arc 70+ E8010-G 80-97,000 (552-669) 67-82,000 (462-565)
Shield-Arc 90 E9010-G 90-100,000 (620-689) 77-88,000 (531-607)

Low Hydrogen Electrode
LH-D80 E8018-G 89,600 ( 618) 76,800 (530)
Jet-LH
E8018-C3 80-94,000 (551-648) 68-80,000 (469-552)
8018-C3 MR
Jet-LH E8018-C1 80-95,000 (551-655) 67-81,000 (462-558)
8081-C1 MR
LH-D80 E8018-G 89,000 (618) 76,800 (530)
LH-D90 E9018-G 99,000 (682) 89,000 (614)
LH-D100 E10018-G 106,000 (731) 98,500 (679)
Jetweld
E8018-B2 97-107,000 (669-738) 84-97,000 (579-669)
LH-90 MR
Jetweld LH- MIL-
(938-1013) 122-131,000 82-110,000 (565-758)
101-116,000 (696-800) (841-903)
100M1 MR 10018-M1
Jet-LH
E8018-B2 112-121,000 (772-834) 100-107,000 (689-738)
8018-B2 MR
Jetweld LH-
E11018-M 110-128,000 (758-882) 98-109,000 (676-751)
110M MR
Jet-LH
E9018-B3136-147,000
9018-B3 MR

Lincoln 16P E7016 85-90,100 (586-621) 74900-78,000 (517-538)

Lincoln 18P E8018-G 99-105 (683-727) 88700-97200 612-650

(1)
Stress relieved @ 1275°F (691°C).
(2)
Stress relieved @ 1125°F (607°C).

-34-

Stress Relieved @ 1150°F (621°C)
% Tensile Strength Yield Strength %
Elong. psi (MPa) psi (MPa) Elong.

22-33 60-69,000 (414-476) 48-61,000 (331-421) 28-36
22-33 67-78,000 (461-538) 51-67,000 (351-461) 30-34
22-30 70-84,000 (483-579) 57-74,000 (393-512) 22-30
22-30 80-82,000 (552-565) 72-76,000 (496-524) 24-27
- - - -
19-26 — — —
19-31 80-88,000 (552-607) 65-78,000 (448-538) 29-31
17-26 — — —

28 — — —

24-30 75-84,000 (517-579) 66-73,000 (455-503) 24-32

19-25 80-96,000 (552-662) 66-81,000 (455-558) 19-32

28 __ __ __
29 — — —
- - - - - -
(1)
17-24 90-107,000 (620-738) 77-95,000 (531-655) 17-24

(2) (2) (2)
20-24 99-111,000 (683-765) 88-104,000 (607-717) 20-26

(1) (1)
17-24 93-103,000 (641-710) 81-93,000 (558-641) 25-28

(2) (2) (2)
20-24 110-120,000 (758-827) 95-107,000 (655-738) 20-26

(1) (1)
15-22 100-114,000 (689-786) 86-100,000 (593-689) 21-25

28-30

28

NOTE: Mechanical properties obtained with each type electrode
also depends upon (1) chemistry of the pipe, (2) welding procedures
and (3) the rate of cooling. Since these factors vary between actual
applications and testing conditions, the mechanical properties may
also vary.

-35-

In-Plant Pipe
Vertical Up Welding
Pipe End Cleaning
Pipe may be covered with a variety of coatings, which include
primers, epoxy, tar, paper, varnish, rust, scale, moisture or organic
contaminants. Failure to recognize and properly clean these joints
can contribute to rejected welds and costly repairs. Joint cleanliness
is especially important in welding pipe.
Follow these guidelines to minimize welding defects such as root
pass hollow bead:
• Moisture and condensation of any type must be removed prior to
welding.
• Clean both ends of the pipe on the inside and outside surfaces.
The area to be cleaned should extend at least 1” (25mm) from the
end of the bevel on both the inside and outside surfaces.
• A recommended method for cleaning pipe is the use of a heavy
duty straight shaft grinder with a rubber expanding wheel and a
carbide coated sleeve. The small shaft and reduced overall weight
allow easy access to both the inside and outside pipe surfaces.

Pipe End Preparation with No Backup Ring
The dimensional requirements for welding vertically up are shown
below. A 1/8” (3.2mm) gap must be maintained accurately all the way
around the joint. When no backup ring is used a 1/8” Fleetweld 5P or
5P+ are recommended for the root pass.

BEVEL 30° + 0 1/2
7
–

LAND
T 3/32 - 1/8"

3/32 - 1/8" GAP

-36-

Pipe End Preparation With Backup Ring
Alloy pipe is often welded vertically up using a low hydrogen elec-
trode. When a low hydrogen electrode is used for the first pass a
backup ring maybe used. With a backup ring, the pipe ends are
made with a feather edge. The gap should be about the same as
the diameter of the electrode with coating and must be consistent all
the way around.

BEVEL 30° + 0 1/2
7
–

T

GAP "G" BACK UP RING
"G" EQUALS DIAMETER OF THE ELECTRODE
WITH COATING

Mixed E6010, E7010, E8010, E9010 and Low Hydrogen Beads
When low hydrogen electrode is to be used, a root pass of EXX10
electrode may be necessary or advantageous. This usually arises
when a special fitting with reduced gap is used or where a backup
ring is undesirable.
The E6010 - E9010 root pass is needed to provide adequate pene-
tration to reach the root of the joint. By applying the E6010 - E9010
stringer bead vertically down, the first weld can be applied at higher
speeds. The smaller gap also reduces the amount of electrode need-
ed to complete the weld.

-37-

Pipe Axis - Horizontal & Vertical
First Pass
The sections are lined and tacked into position with at least four tack
welds. The root pass is made from bottom to top, one side at a time.
No Backup Ring
When no backup ring is used, the penetration must be complete on
both lips and there must be some buildup on the inside of the joint.
This inside bead should have an even surface and be at least 1/16”
(1.6 mm) when starting a fresh electrode during the root pass, spe-
cial care must be taken to maintain a smooth uninterrupted inside
bead. With pipe axis vertical, some codes require a full width weave
oove by 1/16 to 1/8” (1.6 to 3.2mm).
for the cover pass. This weave is illustrated below:

1/8" EXX10
80 - 110 AMPS

5/32" EXX10
120 - 150 AMPS

With Backup Ring
The root pass must penetrate into both the lands of both pipes and
into the backing ring to weld pipe sections and the ring into one
1/16” (1.6mm) higher than the both
integral piece.
5/32" EXX18
1/8" EXX18
140 - 160 AMPS
115 - 135 AMPS
13 14 23
11 12 16
8
10
9
3/32" EXX18 10
11
6 7 85 - 105 AMPS 3
6 5/32" EXX18
5 1
4 1/8" EXX18 2 140 - 160 AMPS
3 4
2 115 - 135 AMPS 7
1 12
17

3/32" EXX18
85 - 105 AMPS

Horizontal Vertical

Filler Passes
Clean each bead before starting the next pass. Never start a bead at
the same point as the previous bead was started. Use enough heat
to assure complete fusion with the pipe wall and the adjacent bead.
The finish passes should be about
walls and overlap the original gr
For horizontal cap passes, particular care should be exercised to

-38-

avoid undercutting on the top of the weld pass. Lower currents and a
short arc should be used to minimize undercutting.

Vertical Up Procedures
Vertical Joint - (Pipe Axis Horizontal)

E6010, E7010, E8010 or E9010: DC+

Low Hydrogen Electrode: DC+
Wall
5/32" EXX10 1/8" EXX18 Thickness No. of
OR 115 - 135 AMPS
115 - 125 AMPS In. (mm) Passes(1)
1/4 (6.4) 2
T 5/16 (7.9) 2
3/8 (9.5) 3
1/8" EXX10 1/8" 1/2 (12.7) 3
85 - 95 AMPS 5/8 (15.9) 4
3/4 (19.0) 6
1 (25.4) 7

5/32" EXX18, 140 - 160 AMPS Wall
Thickness No. of
13 14
11
10
12 In. (mm) Passes(1)
8 9
6
5
7
3/8 (9.5) 3
4 1/8" EXX18
3
2 115 - 135 AMPS 1/2 (12.7) 4
1 5/8 (15.9) 5
3/4 (19.0) 7
3/32" EXX18, 85 - 105 AMPS 1 (25.4) 10
Horizontal Joint - (Pipe Axis Vertical)

E6010, E7010, E8010 or E9010: DC+

Wall
Thickness No. of
1/8" EXX10 In. (mm) Passes(1)
80 - 110 AMPS
1/4 (6.4) 2
5/32" EXX10
5/16 (7.9) 3
120 - 150 AMPS 3/8 (9.5) 4
OR 1/2 (12.7) —
1/8" EXX18 5/8 (15.9) —
115 - 135 AMPS 3/4 (19.0) —
1 (25.4) —
(1) The number of passes may vary depending on operator techniques.

-39-

Vertical Up Electrode Consumption

Wall Thickness

3/8” (9.5 mm) 1/2” (12.7 mm)

Pipe
Diameter In. (mm) 3/32” 1/8” Total 3/32” 1/8” Total
6 In. (152.4 mm) .51 1.34 1.85 .51 2.31 2.82
8 In. (203.2 mm) .70 1.8 2.5 .70 3.1 3.8
12 In. (304.8 mm) 1.0 2.7 3.7 1.0 4.7 5.7
16 In. (406.4 mm) 1.4 3.6 5.0 1.4 6.1 7.5
20 In. (508 mm) 1.7 4.5 6.2 1.7 7.7 9.4
24 In. (609.6 mm) 2.0 5.4 7.4 2.0 9.3 11.3
28 In. (711.2 mm) 2.4 6.2 8.6 2.4 10.8 13.2
32 In. (812.8 mm) 2.7 7.2 9.9 2.7 12.4 15.1
36 In. (914.4 mm) 3.1 8.0 11.1 3.1 13.9 17.0
40 In. (1016 mm) 3.4 8.9 12.3 3.4 15.4 18.8
48 In. (1219 mm) 4.1 14.7 18.8 4.1 18.5 22.6
60 In. (1524 mm) — — — 5.1 23.2 28.3

The table above estimates consumption of low hydrogen electrodes.
It can be used for estimating E6010, E7010, E8010 or E9010 con-
sumption for vertical up or horizontal joints with the following adjust-
ments made:

• E6010, E7010, E8010 and E9010 welds require a narrower gap,
therefore, total electrode required is less. To estimate the total elec-
trode required, multiply the “Total” figures in the table by 0.9.

• The first pass in E6010, E7010, E8010 or E9010 welds is made
with 1/8” electrode. In low hydrogen welds, the first two or three
passes are made with 3/32” electrode. To estimate the amount of
1/8” electrode required, multiply the 3/32” figures in the table by
0.7.

-40-

Wall Thickness

5/8” (15.87 mm) 3/4” (19.05 mm) 1” (25.4 mm)

1/8 & 1/8 &
3/32” 1/8” Total 3/32” 5/32” Total 3/32” 5/32” Total

.70 4.7 5.4
1.0 7.1 8.1 1.0 9.9 10.9 1.0 16.7 17.7
1.4 9.8 11.2 1.4 13.1 14.5 1.4 22.1 23.5
1.7 11.7 13.4 1.7 16.4 18.1 1.7 27.6 29.3
2.0 14.2 16.2 2.0 19.8 21.8 2.0 33.4 35.4
2.4 16.5 18.9 2.4 23.0 25.4 2.4 38.8 41.2
2.7 19.0 21.7 2.7 26.5 29.2 2.7 44.5 47.2
3.1 21.6 24.7 3.1 29.6 32.7 3.1 49.9 53.0
3.4 23.5 26.9 3.4 32.8 36.2 3.4 55.3 58.7
4.1 28.3 32.4 4.1 39.5 43.6 4.1 66.6 70.7
5.1 45.4 50.5 5.1 49.4 54.5 5.1 83.2 88.3

-41-

ASTM Pipe Steels
These recommended electrodes were based on the needed
mechanical properties - especially tensile and yield strength. In some
cases, particularly for low temperature steels, the suggested elec-
trodes also approximate the alloy content of the plate to provide simi-
lar properties at the service temperatures.

The suggested electrodes will generally meet the requirements of
common government and industry codes. However, you must check
the code against the deposit properties and the conformances and
approvals of the specific electrode to be sure.

Preheat may be required when welding high strength steels. The
amount of preheat needed increases with heavier wall thickness and
higher carbon and alloy contents.

NOTE: The Lincoln Electric Company strongly recommends for weldments
intended for sour gas, sour crude, or other critical service applications, that
the customer verifies that both the level of hardness and variation in hardness
of the weld, heat affected zone and base plate are within acceptable limits.

Carbon and Alloy Steel Pipe
Grades and Suggested Electrodes
ASTM Suggested
Spec Description Grades Electrodes

A105 High Temp. Fittings I, II LH-78
A161 Carbon Steel Still Tubes Low Carbon (1), Excalibur 7018-1, LH-78,
C-Mo Steel Still Tubes T1 SA-85, Excalibur 7018-1,
LH-78
A178 Boiler Tubes A (1). Excalibur 7018-1, LH-78
C Excalibur 7018-1, LH-78
A181
A182 High Temp. Fittings, etc. F1 SA-85, LH-7018-A1,
LH-8018-B2
F2, F11, F12 LH-90, LH-8018-B2
A199 Heat Exchanger Tubes T11 LH-8018-B2
A200 Refinery Still Tubes T11 LH-8018-B2
A209 C-Mo Boiler Tubes T1, T1a, T1b SA-85,
Excalibur 7018-1, LH-78
A210 Carbon Steel Boiler Tubes A1 (1), 60XX, 70XX
C SA-85,
Excalibur 7018-1, LH-78
A213 Boiler Tubes T2 LH-90, LH-8018-B2
T11, T12, T17 LH-90, LH-8018-B2
A216 High Temp. Cast Fittings
Excalibur 7018-1
A217 High Temp. Cast Fittings WC1 SA-85, LH-7018-A1
WC4, WC6 LH-90, LH-8018-B2
A234 Wrought Welding Fixtures WPB, WPC (1), LH-78
WP1 LH-7018-A1, SA-85,
WP11, WP12 LH-90, LH-8018-B2
(1) Fleetweld 5P, 5P+, 35 and 35LS.
(2) LH-78. LH-90, LH-8018-B2 are “MR”.
-42-

WCA, WCB, WCC Excalibur
General Service Fittings, etc. 7018, I, II
LH-75, Excalibur 7018-1, LH-78

Carbon and Alloy Steel Pipe
Grades and Suggested Electrodes

ASTM Suggested
Spec Description Grades Electrodes

A250 C-Mo Tubes T1, T1a, T1b SA-85, LH-7018-A1
A333 Low Temp. Pipe 1, 6 Excalibur 7018-1, LH-78,
LH-7018-A1
7 LH-8018-C1
LH-78 Low Temp. Pipe
A334 1, 6 LH-75, LH-78, LH-7018-A1
7 LH-8018-C1
A335 High Temp. Pipe P1 LH-7018-A1
P2, P11, P12 LH-90, LH-8018-B2
A350 Low Temp. Fittings, etc. LF1, LF2 Excalibur 7018-1, LH-78,
LH-8018-C3
A369 High Temp. Pipe See A335 & A182
A381 High Pressure Pipe Y35, Y42, Y46 (1), Excalibur 7018-1, LH-78
Y52, Y56 SA-HYP, SA-85,
SA-70+, SA-80,
Excalibur 7018-1,
Y60, Y65 SA-HYP, SA-70+, SA-80
A405 High Temp. Pipe P24 LH-9018-B3, LH-90
A420 Low Temp. Fittings WPL6 Excalibur 7018-1, LH-78,
LH-8018-C3
Low Carbon Steel Chem. Pipe
A423 Low Alloy Tubes 1 (1) LH-90, LH-8018-B2
2 LH-8018-C3
A426 High Temp. Cast Pipe See A335
A498 Condenser Tubes See A199, A213, A334
A500 Structural Tubing A, B, C (1)
A501 Structural Tubing (1)
A524 Seamless Carbon Steel Pipe I, II (1)
A556 Feedwater Heater Tubes A2 (1)
A557 B2, C2 Excalibur 7018-1, LH-78
A587
A595 Structural A, B Excalibur 7018-1, LH-78
A618 Structural Tubing (1) ,Excalibur 7018-1, LH-78
A660 Cast High Temp. Pipe WCA (1), Excalibur 7018-1, LH-78
WCB, WCC Excalibur 7018-1, LH-78
A692 Seamless Low-Alloy Tubes SA-85, LH-7018-A1
A694 Carbon & Alloy Steel Forgings All Excalibur 7018-1, LH-78,
LH-8018-C3
A696 Carbon Steel Bars Excalibur 7018-1, LH-78
A699 Low Carbon Alloy Steel Plate,
Shapes & Bars LH-90, LH-110M MR
A707 Carbon & Alloy Steel Flanges L1, L2, L3 Excalibur 7018-1, LH-78,
LH-8018-C3
L4, L5, L6 LH-8018-C1
A714 Low Alloy Pipe I, II, III Excalibur 7018-1, LH-78
IV LH-8018-C3
V LH-8018-C1
VI LH-8018-C3
A727 Notch Tough Carbon Steel
Forgings Excalibur 7018-1, LH-78

(1) Fleetweld 5P, 5P+, 35 and 35LS.

-43-

WARNING
ARC WELDING can be hazardous.
PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS
INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER
WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE
OPERATING.
Read and understand the following safety highlights. For additional safety infor-
mation it is strongly recommended that you purchase a copy of “Safety in
Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society,
P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free
copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric
Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTE-
NANCE, AND REPAIR PROCEDURES ARE PERFORMED ONLY BY
QUALIFIED INDIVIDUALS.

ELECTRIC SHOCK can kill.
1.a. The electrode and work (or ground) circuits are electrically
“hot” when the welder is on. Do not touch these “hot” parts with
your bare skin or wet clothing. Wear dry, hole-free gloves to
insulate hands.
1.b. Insulate yourself from work and ground using dry insula-
tion. Make certain the insulation is large enough to cover your
full area of physical contact with work and ground.
In addition to the normal safety precautions, if welding must be per-
formed under electrically hazardous conditions (in damp locations or
while wearing wet clothing; on metal structures such as floors, gratings
or scaffolds; when in cramped positions such as sitting, kneeling or
lying, if there is a high risk of unavoidable or accidental contact with
the workpiece or ground) use the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
1.c. In semiautomatic or automatic wire welding, the electrode, electrode reel,
welding head, nozzle or semiautomatic welding gun are also electrically
“hot”.
1.d. Always be sure the work cable makes a good electrical connection with the
metal being welded. The connection should be as close as possible to the
area being welded.
1.e. Ground the work or metal to be welded to a good electrical (earth) ground.
1.f. Maintain the electrode holder, work clamp, welding cable and welding machine
in good, safe operating condition. Replace damaged insulation.
1.g. Never dip the electrode in water for cooling.
1.h. Never simultaneously touch electrically “hot” parts of electrode holders con-
nected to two welders because voltage between the two can be the total of
the open circuit voltage of both welders.
1.i. When working above floor level, use a safety belt to protect yourself from a fall
should you get a shock.
1.j. Also see Items 4.c. and 6.

ARC RAYS can burn.
2.a. Use a shield with the proper filter and cover plates to pro-
tect your eyes from sparks and the rays of the arc when weld-
ing or observing open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
2.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from the arc rays.

-44-

2.c. Protect other nearby personnel with suitable non-flammable screening
and/or warn them not to watch the arc nor expose themselves to the arc rays
or to hot spatter or metal.

FUMES AND GASES can be
dangerous.
3.a. Welding may produce fumes and gases hazardous to
health. Avoid breathing these fumes and gases.When
welding, keep your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep fumes and
gases away from the breathing zone. When welding
with electrodes which require special ventilation
such as stainless or hard facing (see instructions on
container or MSDS) or on lead or cadmium plated steel and other
metals or coatings which produce highly toxic fumes, keep expo-
sure as low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In confined spaces or
in some circumstances, outdoors, a respirator may be required.
Additional precautions are also required when welding on galva-
nized steel.
3.b. Do not weld in locations near chlorinated hydrocarbon vapors coming
from degreasing, cleaning or spraying operations. The heat and rays of
the arc can react with solvent vapors to form phosgene, a highly toxic
gas, and other irritating products.
3.c. Shielding gases used for arc welding can displace air and cause injury or
death. Always use enough ventilation, especially in confined areas, to
insure breathing air is safe.
3.d. Read and understand the manufacturer’s instructions for this equipment
and the consumables to be used, including the material safety data sheet
(MSDS) and follow your employer’s safety practices. MSDS forms are
available from your welding distributor or from the manufacturer.
3.e. Also see item 7b.

WELDING SPARKS can cause fire
or explosion.
4.a..Remove fire hazards from the welding area. If this is not
possible, cover them to prevent the welding sparks from
starting a fire. Remember that welding sparks and hot mate-
rials from welding can easily go through small cracks and
openings to adjacent areas. Avoid welding near hydraulic
lines. Have a fire extinguisher readily available.
4.b. Where compressed gases are to be used at the job site, special precautions
should be used to prevent hazardous situations. Refer to “Safety in Welding
and Cutting” (ANSI Standard Z49.1) and the operating information for the
equipment being used.

4.c. When not welding, make certain no part of the electrode circuit is touching
the work or ground. Accidental contact can cause overheating and create a
fire hazard.

4.d. Do not heat, cut or weld tanks, drums or containers until the proper steps
have been taken to insure that such procedures will not cause flammable or
toxic vapors from substances inside. They can cause an explosion even
though they have been “cleaned.” For information purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of Containers and
Piping That Have Held Hazardous Substances”, AWS F4.1 from the
American Welding Society (see address above).

-45-

4.e. Vent hollow castings or containers before heating, cutting or welding. They
may explode.

4.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective
garments such as leather gloves, heavy shirt, cuffless trousers, high shoes
and a cap over your hair. Wear ear plugs when welding out of position or in
confined places. Always wear safety glasses with side shields when in a
welding area.

4.g. Connect the work cable to the work as close to the welding area as practical.
Work cables connected to the building framework or other locations away
from the welding area increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits. This can cre-
ate fire hazards or overheat lifting chains or cables until they fail.

4.h. Also see item 7c.

CYLINDER may explode if damaged.
5.a. Use only compressed gas cylinders containing the correct
shielding gas for the process used and properly operating reg-
ulators designed for the gas and pressure used. All hoses, fit-
tings, etc. should be suitable for the application and main-
tained in good condition.
5.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.

5.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.

5.d. Never allow the electrode, electrode holder or any other electrically “hot”
parts to touch a cylinder.

5.e. Keep your head and face away from the cylinder valve outlet when opening
the cylinder valve.

5.f. Valve protection caps should always be in place and hand tight except when
the cylinder is in use or connected for use.

5.g. Read and follow the instructions on compressed gas cylinders, associated
equipment, and CGA publication P-l, “Precautions for Safe Handling of
Compressed Gases in Cylinders,”available from the Compressed Gas
Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered
equipment.
6.a. Turn off input power using the disconnect switch at the
fuse box before working on the equipment.
6.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the
manufacturer’s recommendations.

6.c. Ground the equipment in accordance with the U.S. National Electrical Code
and the manufacturer’s recommendations.

FOR ENGINE powered equipment.
7.a Turn the engine off before troubleshooting and
maintenance work unless the maintenance work
requires it to be running.

-46-

7.b. Operate engines in open, well-ventilated areas or vent
the engine exhaust fumes outdoors.

-------------------------------------------------------------------------------
-------
7.c.Do not add the fuel near an open flame welding arc or
when the engine is running. Stop the engine and allow it to
cool before refueling to prevent spilled fuel from vaporizing
on contact with hot engine parts and igniting. Do not spill
fuel when filling tank. If fuel is spilled, wipe it up and do not
start engine until fumes have been eliminated.
-------------------------------------------------------------------------------
--------
7.d. Keep all equipment safety guards, covers and devices
in position and in good repair. Keep hands, hair, clothing
and tools away from V-belts, gears, fans and all other mov-
ing parts when starting, operating or repairing equipment.

7.e. In some cases it may be necessary to remove safety guards to per-
form required maintenance. Remove guards only when necessary
and replace them when the maintenance requiring their removal is
complete. Always use the greatest care when working near moving
parts.

7.f. Do not put your hands near the engine fan. Do not attempt to override
the governor or idler by pushing on the throttle control rods while
the engine is running.

7.g. To prevent accidentally starting gasoline engines while turning the engine or
welding generator during maintenance work, disconnect the
spark plug wires, distributor cap or magneto wire as appro-
priate.

7.h. To avoid scalding, do not remove the radiator pressure
cap when the engine is hot.

HAVE ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR
WORK performed by qualified people.

For more detailed information, it is strongly recommended that you
purchase a copy of “Safety in Welding and Cutting - ANSI Standard
Z49.1”, from the American Welding Society, P.O. Box 351040, Miami,
FL 33135.
Apr. ‘93

-47-

Customer Assistance Policy
The business of The Lincoln Electric Company is
manufacturing and selling high quality welding
equipment, consumables, and cutting equip-
ment. Our challenge is to meet the needs of our
customers and to exceed their expectations. On
occasion, purchasers may ask Lincoln Electric
for advice or information about their use of our
products. We respond to our customers based
on the best information in our possession at that
time. Lincoln Electric is not in a position to war-
rant or guarantee such advice, and assumes no
liability, with respect to such information or
advice. We expressly disclaim any warranty of
any kind, including any warranty of fitness for
any customer’s particular purpose, with respect
to such information or advice. As a matter of
practical consideration, we also cannot assume
any responsibility for updating or correcting any
such information or advice once it has been
given, nor does the provision of information or
advice create, expand or alter any warranty with
respect to the sale of our products.

Lincoln Electric is a responsive manufacturer,
but the selection and use of specific products
sold by Lincoln Electric is solely within the con-
trol of, and remains the sole responsibility of the
customer. Many variables beyond the control of
Lincoln Electric affect the results obtained in
applying this type of fabrication methods and
service requirements.

Stick
C2.420 10/02

Welding of pipelines

More Related Content

What's hot (20)

Similar to Welding of pipelines (20)

Recently uploaded (20)

Welding of pipelines