1. mathematical fundamentals

Mathematical Fundamentals
Introduction :
Electromagnetic theory is a discipline concerned with the study of charges at rest and in motion. Electromagnetic
principles are fundamental to the study of electrical engineering and physics. Electromagnetic theory is also
indispensable to the understanding, analysis and design of various electrical, electromechanical and electronic
systems. Some of the branches of study where electromagnetic principles find application are:
RF communication
Microwave Engineering
Antennas
Electrical Machines
Satellite Communication
Atomic and nuclear research
Radar Technology
Remote sensing
EMI EMC
Quantum Electronics
VLSI
Electromagnetic theory is a prerequisite for a wide spectrum of studies in the field of Electrical
Sciences and Physics. Electromagnetic theory can be thought of as generalization of circuit
theory. There are certain situations that can be handled exclusively in terms of field theory. In
electromagnetic theory, the quantities involved can be categorized assource quantities and field
quantities. Source of electromagnetic field is electric charges: either at rest or in motion.
However an electromagnetic field may cause a redistribution of charges that in turn change the
field and hence the separation of cause and effect is not always visible.
Electric charge is a fundamental property of matter. Charge exist only in positive or negative
integral multiple ofelectronic charge, -e, e= 1.60 × 10-19 coulombs. [It may be noted here that in
1962, Murray Gell-Mann hypothesized Quarks as the basic building blocks of matters. Quarks
were predicted to carry a fraction of electronic charge and the existence of Quarks have been
experimentally verified.] Principle of conservation of charge states that the total charge (algebraic
sum of positive and negative charges) of an isolated system remains unchanged, though the
charges may redistribute under the influence of electric field. Kirchhoff's Current Law (KCL) is an
assertion of the conservative property of charges under the implicit assumption that there is no
accumulation of charge at the junction.

Electromagnetic theory deals directly with the electric and magnetic field vectors where as circuit
theory deals with the voltages and currents. Voltages and currents are integrated effects of
electric and magnetic fields respectively. Electromagnetic field problems involve three space
variables along with the time variable and hence the solution tends to become correspondingly
complex. Vector analysis is a mathematical tool with which electromagnetic concepts are more
conveniently expressed and best comprehended. Since use of vector analysis in the study of
electromagnetic field theory results in real economy of time and thought, we first introduce the
concept of vector analysis.
Vector Analysis:
The quantities that we deal in electromagnetic theory may be either scalar or vectors [There are
other class of physical quantities called Tensors: where magnitude and direction vary with co
ordinate axes]. Scalars are quantities characterized by magnitude only and algebraic sign. A
quantity that has direction as well as magnitude is called a vector. Both scalar and vector
quantities are function of time and position . A field is a function that specifies a particular quantity
everywhere in a region. Depending upon the nature of the quantity under consideration, the field
may be a vector or a scalar field. Example of scalar field is the electric potential in a region while
electric or magnetic fields at any point is the example of vector field.
A vector can be written as, , where, is the magnitude and is the unit
vector which has unit magnitude and same direction as that of .
Two vector and are added together to give another vector . We have
................(1.1)
Let us see the animations in the next pages for the addition of two vectors, which has two rules:
1: Parallelogram law and 2: Head & tail rule
Vector Subtraction is similarly carried out: ........................(1.2)

Scaling of a vector is defined as , where is scaled version of vector and is a
scalar.
Some important laws of vector algebra are:
Commutative Law..........................................(1.3)
Associative Law.............................................(1.4)
Distributive Law ............................................(1.5)
The position vector of a point P is the directed distance from the origin (O) to P, i.e., =
.
Fig 1.3: Distance Vector
If = OP and = OQ are the position vectors of the points P and Q then the distance vector

Product of Vectors
When two vectors and are multiplied, the result is either a scalar or a vector depending
how the two vectors were multiplied. The two types of vector multiplication are:
Scalar product (or dot product) gives a scalar.
Vector product (or cross product) gives a vector.
The dot product between two vectors is defined as = |A||B|cosθAB ..................(1.6)
Vector product
is unit vector perpendicular to and
Fig 1.4 : Vector dot product
The dot product is commutative i.e., and distributive i.e., .
Associative law does not apply to scalar product.
The vector or cross product of two vectors and is denoted by . is a vector
perpendicular to the plane containing and , the magnitude is given by and
direction is given by right hand rule as explained in Figure 1.5.
............................................................................................(1.7)
where is the unit vector given by, .
The following relations hold for vector product.

= i.e., cross product is non commutative ..........(1.8)
i.e., cross product is distributive.......................(1.9)
i.e., cross product is non associative..............(1.10)
Scalar and vector triple product :
Scalar triple product .................................(1.11)
Vector triple product ...................................(1.12)
Co-ordinate Systems
In order to describe the spatial variations of the quantities, we require using appropriate co-
ordinate system. A point or vector can be represented in a curvilinear coordinate system that
may be orthogonal or non-orthogonal .
An orthogonal system is one in which the co-ordinates are mutually perpendicular. Non-
orthogonal co-ordinate systems are also possible, but their usage is very limited in practice .
Let u = constant, v = constant and w = constant represent surfaces in a coordinate system, the
surfaces may be curved surfaces in general. Furthur, let , and be the unit vectors in the
three coordinate directions(base vectors). In a general right handed orthogonal curvilinear
systems, the vectors satisfy the following relations :
.....................................(1.13)
These equations are not independent and specification of one will automatically imply the other
two. Furthermore, the following relations hold
................(1.14)

A vector can be represented as sum of its orthogonal components,
...................(1.15)
In general u, v and w may not represent length. We multiply u, v and w by conversion
factors h1,h2 and h3 respectively to convert differential changes du, dv and dw to corresponding
changes in length dl1, dl2, and dl3. Therefore
...............(1.16)
In the same manner, differential volume dv can be written as and differential
area ds1 normal to is given by, . In the same manner, differential areas normal
to unit vectors and can be defined.
In the following sections we discuss three most commonly used orthogonal co-ordinate
systems, viz:
1. Cartesian (or rectangular) co-ordinate system
2. Cylindrical co-ordinate system
3. Spherical polar co-ordinate system
Cartesian Co-ordinate System :
In Cartesian co-ordinate system, we have, (u,v,w) = (x,y,z). A point P(x0, y0, z0) in Cartesian co-
ordinate system is represented as intersection of three planes x = x0, y = y0 and z = z0. The unit
vectors satisfies the following relation:

Fig 1.6:Cartesian co-ordinate system
....................(1.17)
.....................(1.18)
In cartesian co-ordinate system, a vector can be written as . The dot
and cross product of two vectors and can be written as follows:
.................(1.19)

....................(1.20)
Since x, y and z all represent lengths, h1= h2= h3=1. The differential length, area and volume are
defined respectively as
................(1.21)
.................................(1.22)
Cylindrical Co-ordinate System :
For cylindrical coordinate systems we have a point is determined
as the point of intersection of a cylindrical surface r = r0, half plane containing the z-axis and
making an angle ; with the xz plane and a plane parallel to xy plane located at z=z0 as
shown in figure 7 on next page.
In cylindrical coordinate system, the unit vectors satisfy the following relations
.....................(1.23)
A vector can be written as , ...........................(1.24)

The differential length is defined as,
......................(1.25)
Fig 1.7 : Cylindrical Coordinate System

Differential
areas are:
..............(1.26)
Differential
volume,
.................(1.27
)
Fig 1.8 : Differential Volume Element in Cylindrical Coordinates

Transformation between Cartesian and Cylindrical coordinates:
Let us consider is to be expressed in Cartesian co-ordinate
as . In doing so we note that
and it applies for other components as well.
Fig 1.9 : Unit Vectors in Cartesian and Cylindrical Coordinates
...............(1.28)
Therefore we can write, ..........(1.29)

These relations can be put conveniently in the matrix form as:
.....................(1.30)
themselves may be functions of as:
............................(1.31)
The inverse relationships are: ........................(1.32)
Fig 1.10: Spherical Polar Coordinate System

Thus we see that a vector in one coordinate system is transformed to another coordinate system
through two-step process: Finding the component vectors and then variable transformation.
Spherical Polar Coordinates:
For spherical polar coordinate system, we have, . A point is
represented as the intersection of
(i) Spherical surface r=r0
(ii) Conical surface ,and
(iii) half plane containing z-axis making angle with the xz plane as shown in the figure 1.10.
The unit vectors satisfy the following relationships: .....................................(1.33)
The orientation of the unit vectors are shown in the figure 1.11.

Fig 1.11: Orientation of Unit Vectors
A vector in spherical polar co-ordinates is written as :
and
For spherical polar coordinate system we have h1=1, h2= r and h3= .
Fig 1.12(a) : Differential volume in s-p coordinates

Fig 1.12(b) : Exploded view
With reference to the Figure 1.12, the elemental areas are:
.......................(1.34)
and elementary volume is given by
........................(1.35)

Coordinate transformation between rectangular and spherical polar:
With reference to the figure 1.13 ,we can write the following equations:
........................................................(1.36)
Fig 1.13: Coordinate transformation
Given a vector in the spherical polar coordinate system, its component
in the cartesian coordinate system can be found out as follows

.................................(1.37)
Similarly,
.................................(1.38a)
.................................(1.38b)
The above equation can be put in a compact form:
.................................(1.39)
The components themselves will be functions of . are related
to x,y and z as:
....................(1.40)
and conversely,
.......................................(1.41a)
.................................(1.41b)
.....................................................(1.41c)
Using the variable transformation listed above, the vector components, which are functions of
variables of one coordinate system, can be transformed to functions of variables of other
coordinate system and a total transformation can be done.
Line, surface and volume integrals
In electromagnetic theory, we come across integrals, which contain vector functions. Some
representative integrals are listed below:

In the above integrals, and respectively represent vector and scalar function of space
coordinates. C,S and Vrepresent path, surface and volume of integration. All these integrals are
evaluated using extension of the usual one-dimensional integral as the limit of a sum, i.e., if a
function f(x) is defined over arrange a to b of values of x, then the integral is given by
.................................(1.42)
where the interval (a,b) is subdivided into n continuous interval of lengths .
Line Integral: Line integral is the dot product of a vector with a specified C; in other words
it is the integral of the tangential component along the curve C.
Fig 1.14: Line Integral
As shown in the figure 1.14, given a vector around C, we define the
integral as the line integral of E along the curve C.

If the path of integration is a closed path as shown in the figure the line integral becomes a closed
line integral and is called the circulation of around C and denoted as as shown in the
figure 1.15.
Fig 1.15: Closed Line Integral
Surface Integral :
Given a vector field , continuous in a region containing the smooth surface S, we define the
surface integral or the flux of through S as as surface
integral over surface S.
Fig 1.16 : Surface Integral

If the surface integral is carried out over a closed surface, then we write
Volume Integrals:
We define or as the volume integral of the scalar function f(function of spatial
coordinates) over the volume V. Evaluation of integral of the form can be carried out as a
sum of three scalar volume integrals, where each scalar volume integral is a component of the
vector
The Del Operator :
The vector differential operator was introduced by Sir W. R. Hamilton and later on developed
by P. G. Tait.
Mathematically the vector differential operator can be written in the general form as:
.................................(1.43)
In Cartesian coordinates:
................................................(1.44)
In cylindrical coordinates:
...........................................(1.45)
and in spherical polar coordinates:
.................................(1.46)
Gradient of a Scalar function:
Let us consider a scalar field V(u,v,w) , a function of space coordinates.
Gradient of the scalar field V is a vector that represents both the magnitude and direction of the maximum space
rate of increase of this scalar field V.

Fig 1.17 : Gradient of a scalar function
As shown in figure 1.17, let us consider two surfaces S1and S2 where the function V has constant
magnitude and the magnitude differs by a small amount dV. Now as one moves from S1 to S2, the
magnitude of spatial rate of change of Vi.e. dV/dl depends on the direction of elementary path
length dl, the maximum occurs when one traverses from S1toS2along a path normal to the
surfaces as in this case the distance is minimum
By our definition of gradient we can write:
.......................................................................(1.47)
since which represents the distance along the normal is the shortest distance between the
two surfaces.
For a general curvilinear coordinate system
....................(1.48)
Further we can write
......................................................(1.49)
Hence,
....................................(1.50)

Also we can write,
............................(1.51)
By comparison we can write,
....................................................................(1.52)
Hence for the Cartesian, cylindrical and spherical polar coordinate system, the expressions for
gradient can be written as:
...................................................................................(1.53)
..................................................................(1.54)
..........................................................(1.55)
The following relationships hold for gradient operator.
...............................................................................(1.56)
where U and V are scalar functions and n is an integer.

It may further be noted that since magnitude of depends on the direction of dl, it is
called thedirectional derivative. If is called the scalar potential function of the
vector function .
Divergence of a Vector Field:
In study of vector fields, directed line segments, also called flux lines or streamlines, represent
field variations graphically. The intensity of the field is proportional to the density of lines. For
example, the number of flux lines passing through a unit surface S normal to the vector measures
the vector field strength.
Fig 1.18: Flux Lines
We have already defined flux of a vector field as
....................................................(1.57)
For a volume enclosed by a surface,
.........................................................................................(1.58)
We define the divergence of a vector field at a point P as the net outward flux from a volume
enclosing P, as the volume shrinks to zero.
.................................................................(1.59)
Here is the volume that encloses P and S is the corresponding closed surface.

Fig 1.19: Evaluation of divergence in curvilinear coordinate
Let us consider a differential volume centered on point P(u,v,w) in a vector field . The flux
through an elementary area normal to u is given by ,
........................................(1.60)
Net outward flux along u can be calculated considering the two elementary surfaces perpendicular to u .
.......................................(1.61)
Considering the contribution from all six surfaces that enclose the volume, we can write
.......................................(1.62)
Hence for the Cartesian, cylindrical and spherical polar coordinate system, the expressions for divergence can
be written as:
................................(1.63)

....................................................................(1.64)
......................................(1.65)
In connection with the divergence of a vector field, the following can be noted
 Divergence of a vector field gives a scalar.
 ..............................................................................(1.66)
Divergence theorem :
Divergence theorem states that the volume integral of the divergence of vector field is equal to
the net outward flux of the vector through the closed surface that bounds the volume.
Mathematically,
Proof:
Let us consider a volume V enclosed by a surface S . Let us subdivide the volume in large
number of cells. Let the kthcell has a volume and the corresponding surface is denoted by Sk.
Interior to the volume, cells have common surfaces. Outward flux through these common
surfaces from one cell becomes the inward flux for the neighboring cells. Therefore when the total
flux from these cells are considered, we actually get the net outward flux through the surface
surrounding the volume. Hence we can write:
......................................(1.67)
In the limit, that is when and the right hand of the expression can be written
as .

Hence we get , which is the divergence theorem.
Curl of a vector field:
We have defined the circulation of a vector field A around a closed path as .
Curl of a vector field is a measure of the vector field's tendency to rotate about a point. Curl ,
also written as is defined as a vector whose magnitude is maximum of the net circulation
per unit area when the area tends to zero and its direction is the normal direction to the area
when the area is oriented in such a way so as to make the circulation maximum.
Therefore, we can write:
......................................(1.68)
To derive the expression for curl in generalized curvilinear coordinate system, we first
compute and to do so let us consider the figure 1.20 :
If C1 represents the boundary of , then we can write
......................................(1.69)
The integrals on the RHS can be evaluated as follows:
.................................(1.70)

................................................(1.71)
The negative sign is because of the fact that the direction of traversal reverses. Similarly,
..................................................(1.72)
............................................................................(1.73)
Adding the contribution from all components, we can write:
........................................................................(1.74)
Therefore,
......................................................(1.75)
In the same manner if we compute for and we can write,
.......(1.76)
This can be written as,
......................................................(1.77)

In Cartesian coordinates: .......................................(1.78)
In Cylindrical coordinates, ....................................(1.79)
In Spherical polar coordinates, ..............(1.80)
Curl operation exhibits the following properties:
..............(1.81)
Stoke's theorem :
It states that the circulation of a vector field around a closed path is equal to the integral
of over the surface bounded by this path. It may be noted that this equality holds
provided and are continuous on the surface.
i.e,
..............(1.82)
Proof:Let us consider an area S that is subdivided into large number of cells as shown in the
figure 1.21.

Fig 1.21: Stokes theorem
Let kthcell has surface area and is bounded path Lk while the total area is bounded by
path L. As seen from the figure that if we evaluate the sum of the line integrals around the
elementary areas, there is cancellation along every interior path and we are left the line integral
along path L. Therefore we can write,
..............(1.83)
As 0
. .............(1.84)
which is the stoke's theorem.

Solved Examples:
1. Given that
a. Determine the angle between the vectors A and B .
b. Find the unit vector which is perpendicular to both A and B .
Solution:
a. We know that for two given vector A and B,
For the two vectors A and B
or
b. We know that is perpendicular to both A and B.
=
The unit vector perpendicular to both A and B is given by,

2. Given the vectors
Find :
a. The vector C = A + B at a point P (0, 2,-3).
b. The component of A along B at P.
Solution:
The vector B is cylindrical coordinates. This vector in Cartesian coordinate can be written as:
Where
The point P(0,2,-3) is in the y-z plane for which .
a. C = A + B
=
=
b. Component of A along B is where is the angle between A is and B.

i.e., =
3. A vector field is given by
Transform this vector into rectangular co-ordinates and calculate its magnitude at P(1,0,1).
Solution:
Given,
The components of the vector in Cartesian coordinates can be computed as follows:

4. The coordinates of a point P in cylindrical co-ordinates is given by . Find the volume
of the sphere that has center at the origin and on which P is a point. If O represents the origin,
what angle OP subtends with z-axis?
Solution:
The radius of the sphere on which P is a point is given by
Therefore, the volume of the sphere

1. mathematical fundamentals

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to 1. mathematical fundamentals (20)

Recently uploaded (20)

1. mathematical fundamentals