11.review of kanban planning and execution in the context of lean manufacturing

Information and knowledge management www.iiste.org
ISSN 2224-5758 (Paper) ISSN 2224-896X (Online)
Vol.1, No.4, 2011

Review of Kanban planning and execution in the context of
Lean manufacturing
Prakash Divakaran (Corresponding Author)
Polyrub Extrusions (India) Pvt.Ltd, Pune, India, E- mail – Prakashtek@gmail.com

Dr.C.T.Sunil Kumar
Food Corporation of India, Trivandrum
Kerala, India,E-mail – hamsingh@ymail.com

Abstract
In this paper the various principles of Kanban planning and execution is illustrated with respect to cellular
manufacturing, total quality management, total preventive maintenance and Engineering change
management concepts as applied to Lean Manufacturing. A detailed investigation of Kaizen costing and
cost analysis is also presented in this paper

1.Kanban Planning and Execution
1.1 Introduction
Kanban is a method for maintaining an orderly flow of material. Kanban cards are used to indicate points at
which material should be ordered, how much material is needed, from where the material should be ordered,
and to where it should be delivered. With IFS’ Kanban solution, you can perform an advanced Kanban
calculation using an actual demand profile to determine whether an inventory stock out is likely to occur
with the current system settings. The system can calculate Kanban quantity or the number of Kanbans
based on past usage of parts. You can recalculate and redeploy your Kanban circuits within a day when
demand shifts IFS’ Kanban solution lets you perform stock out simulations by retrieving demand from a
variety of sources and for different time spans to determine whether you Kanban quantities are balanced
You can use either visual or electronic signals for replenishment. Kanban replenishment can be from
supplier, a sister plant, an inventory location, a location group or a production line. Options for demand
type, Kanban formula, safety factor, signal type, and replenishment type let you adjust the use of Kanbans
to best match your environment.
IFS’ Kanban solution helps you maintain your Kanban cards. You can easily keep track of the number of cards
used in the system, add or subtract cards during seasonal changes in demand, or print or replace cards

1.2. Vendor-Managed Inventory
Instead of sending Kanban signals to your suppliers, you can give them responsibility for and authorization
to replenish goods. IFS’ vendor-managed inventory capabilities and web-based portal technology make it is
easier to collaborate with your suppliers. Instead of sending information back and forth, customers and
suppliers can access inventory balances and future demands through a convenient portal, and the supplier
can replenish stocks as required. The supplier can also use the portal to enter or search for information and
update documents. The supplier becomes another application user, but with limited access.

11

Vol.1, No.4, 2011

1.3 Repetitive Production
With IFS’ production scheduling functionality, you can perform order less, rate-based production. This
reduces the number of report points, and simplifies and automates the production process. Final reporting
of finished items is the only production reporting required, and all components are automatically issued
(back flushed). You get reduced transactions throughout the flow, short cycle times, and less work-in
process inventory. As a result, you can focus on ensuring enough material.

2.Cellular Manufacturing
Arranging operations and/or people in a U-shaped production line allows for better utilization of people and
improves communication. Product flows smoothly from one operation to the next rather than running in a
batch and then sitting in a queue at the next work center waiting for that operation to begin. IFS
Applications™ lets you define an unlimited number of production lines, each with its own dedicated
inventory storage area. Incoming materials are routed directly to the production line at which they will be
consumed. Finished goods completed at the production line can be stored there until being shipped to the
customer.

3.Waste Reduction

Waste is commonly defined as non-value-added activity. Lean practitioners identify seven types of waste:

• Excess (or early) production—producing more than the customer demands, or producing it earlier than
the customer needs it. This ties up valuable labor and material resources that might otherwise be used to
respond to customer demand.

• Delays—waiting for materials, tools, information, equipment, etc. This may be a result of poor planning,
late supplier deliveries, lack of communication, overbooking of equipment, or erratic demand.

• Transportation (to/from processes)—Moving material more often than necessary. Material should be
delivered and stored at its point of use. Why receivematerial at a receiving dock, move it to an inventory
location, and then move it to the production floor when it can be delivered and stored where it is used?

• Inventory—storing more material than is needed. This wastes valuable space and cash. By reducing
inventory, plans for warehouse expansion can usually be postponed or canceled.

• Processing—Doing more work on a part than is necessary, including inspection and reworking. This
wastes time and money. Quality must be built into the manufacturing process so that parts are produced
correctly the first time.

• Defects—Defective parts. Defects consume considerable resources. In addition to the original materials
and labor used to manufacture the part, extra labor and machine time are required to fix the defective part.
If the defective part is sold to a customer, not only will unnecessary shipping costs be lost, but more
resources will be consumed to resolve the eventual complaints.

12

Vol.1, No.4, 2011

• Movement—Excess motion of employees in getting tools, picking parts, or moving from one point to
another. This is usually the result of poorly planned work layout and workflow. A variety of techniques are
available for reducing or eliminating waste. These techniques include value stream analysis, total quality
management, total productive maintenance, Kaizen costing and cost analysis, engineering and change
management, and document management.

4. Total Quality Management

Total quality management (TQM) is a management system used to continuously improve all areas of a
company's operation. Quality functionality is integrated throughout IFS Applications. Failure modes and
effects analysis (FMEA) is a systematic technique for managing risk in a manufacturing process. It involves
recording and analyzing actual and potential problems with a product design or process, along with related
solutions. This information allows you to improve accountability, avoid repeated mistakes, and improve the
quality of the end product. Control plans can be defined to detail the measurements and tests performed at
any operation of a shop order, production schedule, or purchase receipt. This helps to identify defects
before any further value is added to them. Statistical process control (SPC) is a philosophy that emphasizes
the use of statistical techniques, such as control charts, in all areas of a company to make continuous
improvements in quality and productivity by reducing variation in processes. With IFS Quality
Management™, you can create, view, and analyze X bar and R, X-bar and S, X and MR, np, p, c, and u
control charts. IFS Applications also includes material review board (MRB) functionality for handling the
disposition of defective material.

5.Total Productive Maintenance

Total productive maintenance capitalizes on proactive and progressive maintenance methodologies and
calls on the knowledge and cooperation of operators, equipment vendors, engineering, and support
personnel to optimize machine performance. IFS Maintenance™ is a world-class maintenance package that
is completely integrated with IFS’ supply chain management solution. Both maintenance and production
workers have complete visibility into maintenance and production information and schedules. Operators
can regularly perform preventive maintenance on equipment and tools, with maintenance personnel
handling more detailed overhauls and repairs. The result is optimal equipment performance, including the
elimination of breakdowns, a reduction in unscheduled and scheduled downtime, improved utilization,
higher throughput, and better product quality. Bottom-line results include lower operating costs, longer
equipment life, and lower overall maintenance costs.

6. Kaizen Costing and Cost Analysis

Unlike standard costing systems, a Kaizen costing system focuses on continuous cost reduction rather than
simply meeting the standard and avoiding unfavorable variances. As part of the Kaizen process, you verify
that the costing target has been reached and then continuously review existing production conditions to
further reduce costs. In IFS Applications, you can set a cost target, calculate cost gaps, and plan activities to
reduce costs. Major cost reductions can be broken into smaller reductions for which separate activities can
be created that are easier to handle. Each activity is possible to evaluate from a cost reduction potential and
from an investment need.

IFS Applications also allows you to perform commonality analyses. If an item is used in multiple places,
commonality analysis helps you see which components are common for different structures and whether

13

Vol.1, No.4, 2011

they can be used for other parts to save money. Cost/value analysis helps you analyze the costs of a
component or product in relation to customer value.

7. Engineering and Change Management

IFS Applications manages the changes a design goes through during its lifetime in two stages: During the
Engineering Change Requests stage, all change proposals from the organization are registered. These
change proposals might include fault reports from the service department, the design departments own
improvements, or a recommendation from the purchasing department to change supplier material.

The proposals are analyzed and formally approved. Then, in the Engineering Change Order stage, the
design change is planned and implemented. The product structure helps to define items and minimize the
work involved in making modifications. When the work is finished, a new part revision is created.

8. Document Management

For most businesses, managing documentation is not an end in itself. It’s an essential part of day-to-day
operations—a way of ensuring that the right people get the right information at the right time.
Mismanaging the flow of information can result in confusion, unnecessary delays, and costly errors. With
IFS Document Management™, you get full control over your company's documentation so you can focus
on the things that really matter: selling your products and services, keeping your plant and equipment in top
shape, and meeting or exceeding your business goals.

A framework was created to analyze manufacturing systems and assess the impact of various practices on
system performance. A literature review of Lean Manufacturing resulted in the discovery of significant
gaps in two areas: (1) modeling the effects of implementing Lean Manufacturing using control theory
principles, and (2) a design framework for building Cellular Manufacturing Systems and making the
transition from traditional manufacturing to Lean Manufacturing. Work in these areas led to the conclusion
that reducing the Order Lead Time until it is less than Tall, the allowable customer lead time for
post-payment production, would yield tremendous benefits both for individual factories as well as for entire
Linear Distribution Systems. To fill these gaps, a model was created which analyzed the dynamics of
Linear Distribution Systems, and showed how Lean Manufacturing represents an opportunity to sidestep
many previously insurmountable difficulties that arise as a result of producing to fill inventory levels. The
methods for implementation of Lean Principles were explored, from prerequisites for Cellular
Manufacturing Systems, to design and optimization of Cells, through exploration of the improvements in
quality that are possible in Cellular Manufacturing Systems. A thorough a dissemination of the various
contributions to Order Lead Time showed that changeover reduction, information flow, zero defects and
cellular manufacturing are all indispensable in achieving the goal of OLT < Tall. Finally, conclusions were
presented which show that achieving this reduction allows for production under an entirely new philosophy
that completely eliminates capital investment in inventory.

The difficulties that companies face in today’s marketplace are fierce: shifting customer demand, increasing
variation in products and demands for perfect quality. Meeting these demands while dealing with complex
distribution systems and multi-tiered chains of suppliers is better understood in light of system dynamics
(Forrester [1969]) and finding ways to minimize their cyclical nature. The way to escape the pitfalls faced
by aerospace companies today requires a redefinition of inventory and a new production philosophy which
eliminates the need to produce based on forecasts, or to fill stock levels, and to eliminate rework and

14

Vol.1, No.4, 2011

acceptance of non-conformances Lean Manufacturing is a term popularized by Womack, Jones and Roos
[1991] to describe a method for production based on the Toyota Production System (TPS) (Shingo 1989,
Ohno 1988). There is a tremendous body of literature available on the details of the TPS. The purpose of
this thesis is to take the principles enumerated in the literature one step further and show how lean
manufacturing can address the difficulties of aircraft manufacturing as a linear distribution system (LDS).

9.Cellular Manufacturing (CM)- Processing of parts or part families in a single cell, with no backtracking.
Each part follows a predetermined part path, and is said to be trackable. Individual cells may be built
around Group Technology formed part families or based on a single product line (which facilitates ABC
methods). In CM the operators move independently of the part processing time. A cell processes a subset of
the total operations in the production system. Cells process parts sequentially through a series of machines
or manual stations, whereas a job shop processes parts in parallel processing through duplicated machines.
A cellular manufacturing production system is network of logically linked cells (Cochran [1994]). Hence
throughput of cells can be dependent on (a) a single machine’s cycle time (the bottleneck), or (b) the speed
of the material handler or operator.

• Changeover Time- The length of time a machine or processing area is down (not producing parts) in
order to change over from one part type to another. It begins when the machine finishes producing the
last part of type A and ends at the beginning of the production of the first good unit of type B.

• Cost of Order Preparation- The costs incurred by a factory in the process of receiving an order,
releasing it to the floor and closing the order upon receipt by the customer.

• Customer Lead Time- The length of time beginning when a customer places an order and ending
when the customer receives goods to fill that order. It encompasses the Production Lead Time plus the
time required to transmit the order to the factory and the time to ship the product to the customer.

• Defects vs. Errors- a defect is a product or service’s non-fulfillment of an intended requirement or
reasonable expectation for use. An error is the result of improper processing of the part, which leads to
a defect only when the part is inspected and fails. Thus, errors can be fixed before they become defects.

• External Setup Operations- Operations in changeover from one part type to the next which are done
while the machine is still producing parts.
• Final vs. Absolute Defect Rate- the final defect rate reflects only the number of parts that fail the final
inspection. However, the absolute defect rate is a measure of the number of defects for the entire
process from start to finish (see Shingo [1986])

10. Flexible Manufacturing System (FMS)- A group of numerically controlled machine tools
interconnected by a central control system. The various machining cells are interconnected via loading and
unloading stations by an automated transport system. Parts are generally processed in parallel rather than
serially as in a Cellular Manufacturing System. Operational flexibility is enhanced by the ability to execute
all manufacturing tasks on numerous product designs in small quantities. However, there are often
limitations in flexibility due to the hard tooling that is required for material transport and fixturing in each
machining cell. Capital investment is very high as compared to a manned cell.

15

Vol.1, No.4, 2011

11. Group Technology (GT)- A part classification technique used to categorize parts according to one of
two possible similarities: (1) part geometry, or (2) processing similarities. GT is generally used to create
part families which can then be processed in single cell.

12. Informative vs. Subjective Inspections- An informative inspection yields information about a part,
such as a dimensional characteristic. As a subjective inspection is a pass-failure inspection, the inspector
must make a subjective judgment about the quality of a part.

13. Internal Setup Operations- Operations in changeover from one part type to the next which are done
when the machine is stopped (is not producing parts).

14. Job- Work order; an order from a customer which comprises a fixed number of parts of a specified

type.

15. Lot Delay- In batch production, the time spent while the part is waiting for other parts in the batch to be
processed.

16. Lot (or Batch) Production- Producing parts in lots or batches which are greater than one part.

17. Machine Utilization- The ratio of time during which the machine is operating to the total time
available. The operating time should only include time in which product is being produced (setup time is
excluded).

18. Machine Cycle Time- The length of time required for a machine to process one part, not including
loading and unloading time. It can be measured as the length of time beginning when the start button is
pressed and ending when the part can be removed.

19. Manufacturing Lead Time- The length of time from the first operation for a given order until the
entire order has been transported to the shipping area.

20. Order (or Production) Lead Time- The length of time beginning with receipt of an order from a
customer and ending when product for that order has been manufactured and transported to the shipping
area. It includes the Manufacturing Lead Time plus the time required to process the order and begin
production.

21Process vs. Operation- The distinction between a process and an operation is not one of time scale; the
two have different subjects of study. A process is a flow of product from raw materials to finished parts.
Operations are the actions of man, or machine, and what they do to the product.

22. Process Mapping- A systematic analysis of a production system using Time Division Analysis to
determine which operations are integral to a process, and which must be eliminated.

32. Processing Delay- The time spent while a part is in storage, either in queue behind other batches of
parts, or waiting due to machine downtime.

33. Production Balancing- Efforts to make the processing time for a given part at each station in a process
equal. In a perfectly balanced process, no stations will be idle when producing parts using single piece flow.

16

Vol.1, No.4, 2011

34. Production Leveling- Efforts to increase the product mix and decrease the batch size in a
manufacturing system. In Level Production, assuming there is no variation in processing, at least one unit
of each part type is produced each day.

35. Production Synchronization- Efforts to synchronize the start, stop and transport of product at each
machine, station and process. In Synchronous Production, the upstream process produces goods at the same
rate (or Takt time) as the downstream process.

36. Self (or Source) Inspection- Inspection carried out by the person (or factory) which produced the

product.

37. Single Piece Flow- A term describing the processing of parts in a batch size of one. The only
processing lot size in which the lot delay is reduced to zero.

38. Statistical Quality Control (SQC)- The application of statistical techniques to control quality.
Generally refers to monitoring or inspecting some percentage (less than 100%) and inferring the quality of
the rest of the parts from a sample. SQC is subject to and  errors.

39. Successive (or Post-receipt )Inspection- Inspection by a person or factory of goods that were
produced at an upstream station or plant. Traditionally thought to be more objective than self inspections,
since there is no incentive to pass defective parts through the inspection. However, this inspection method
can only discover defects after they have been made (see defects vs. errors).

40.System- A regularly interacting or interdependent group of items forming a unified whole toward the
achievement of a goal.

41.Takt Time- A production rate determined by customer orders (or sales) which specifies the interval of
time between production of successive parts. Is determined from the following equation: total time
available for production per shift (in sec) Takt Time = required number of parts per shift

42.Time Division Analysis- A technique similar to process mapping where a process is analyzed by
tracking a part as it flows from raw materials to the finish crib and constantly specifying whether a part is
being processed, transported, stored or inspected. Storage is further broken down into Lot delay,
Transportation delay, and Processing delay.

43. Transportation Delay- The time spent waiting for the means of transportation (i.e. waiting for a

forklift)

.
44. Value Added vs. Non Value Added Processing- Value added processing refers to processing steps that
will add value to a part, viewed from the eyes of the customer. Non value added processing includes all
processing that does not add value. Thus a cutting operation on a machine is value added processing only if
it creates a feature in the part that is of value to the customer.

45. Volume vs. Part Types Flexibility- Volume flexibility refers to the ability of a manufacturing system to
produce parts at different rates. Part type flexibility refers to the ability to produce a number of different

17

Vol.1, No.4, 2011

part types in a given period of time.
.

References

1. Cell, Charles; VE, Lean, and Six Sigma – Opportunities Leverage, 2004 SAVE International
Conference Proceedings, Canada (2004)
2. Cook, Dr. Michael; An Untapped Market – Energizing VM Usage via the Six Sigma Methodology,
2000 SAVE International Conference Proceedings, USA (2000).
3. Dean, Edwin B.; Value Engineering from the Perspective of Competitive Advantage, USA (2000).
4. Downer, John G.; From Product to Project – Forming Value into a New Shape, 2005 SAVE
International Conference Proceedings, USA (2005).
5. Fong, Patrick Sik-Wah; Charting the Future Directions of Value Engineering, 1999 SAVE
International Conference Proceedings, USA (1999).
6. George, Michael; Lean Six Sigma : Combining Six Sigma Quality with Lean Speed; McGraw Hill;
USA (2002)
7. Hino, Satoshi; Inside the Mind of Toyota : Management Principles for Enduring Growth (English
Translation); Productivity Press, Inc., USA (2006).
8. Johnson, Gordon; Conflicting or Complementing ? A Comprehensive Comparison of Six Sigma and
Value Methodology, 2003 SAVE International Conference Proceedings, USA (2003)
9. Kirk, Bozdogan; A Comparative Review of Lean Thinking, Six Sigma and Related Enterprise
Change Models, Massachusetts Institute of Technology, Lean Aerospace Institute, USA (2003).
10. Lehman, Theresa &Reiser, Paul; Maximizing Value & Minimizing Waste – Value Engineering &
Lean Construction, 2004 SAVE International Conference Proceedings, USA (2004)
11. Liker, Dr. Jeffrey; The Toyota Way, 14 Management Principles from the World’s Greatest
Manufacturer; McGraw Hill, USA (2004)
12. Maurer, John H.; What is Value Analysis / Value Engineering (VA/VE) ? , USA (1999).

18

International Journals Call for Paper
The IISTE, a U.S. publisher, is currently hosting the academic journals listed below. The peer review process of the following journals
usually takes LESS THAN 14 business days and IISTE usually publishes a qualified article within 30 days. Authors should
send their full paper to the following email address. More information can be found in the IISTE website : www.iiste.org

Business, Economics, Finance and Management PAPER SUBMISSION EMAIL
European Journal of Business and Management EJBM@iiste.org
Research Journal of Finance and Accounting RJFA@iiste.org
Journal of Economics and Sustainable Development JESD@iiste.org
Information and Knowledge Management IKM@iiste.org
Developing Country Studies DCS@iiste.org
Industrial Engineering Letters IEL@iiste.org

Physical Sciences, Mathematics and Chemistry PAPER SUBMISSION EMAIL
Journal of Natural Sciences Research JNSR@iiste.org
Chemistry and Materials Research CMR@iiste.org
Mathematical Theory and Modeling MTM@iiste.org
Advances in Physics Theories and Applications APTA@iiste.org
Chemical and Process Engineering Research CPER@iiste.org

Engineering, Technology and Systems PAPER SUBMISSION EMAIL
Computer Engineering and Intelligent Systems CEIS@iiste.org
Innovative Systems Design and Engineering ISDE@iiste.org
Journal of Energy Technologies and Policy JETP@iiste.org
Information and Knowledge Management IKM@iiste.org
Control Theory and Informatics CTI@iiste.org
Journal of Information Engineering and Applications JIEA@iiste.org
Industrial Engineering Letters IEL@iiste.org
Network and Complex Systems NCS@iiste.org

Environment, Civil, Materials Sciences PAPER SUBMISSION EMAIL
Journal of Environment and Earth Science JEES@iiste.org
Civil and Environmental Research CER@iiste.org
Civil and Environmental Research CER@iiste.org

Life Science, Food and Medical Sciences PAPER SUBMISSION EMAIL
Journal of Biology, Agriculture and Healthcare JBAH@iiste.org
Food Science and Quality Management FSQM@iiste.org
Chemistry and Materials Research CMR@iiste.org

Education, and other Social Sciences PAPER SUBMISSION EMAIL
Journal of Education and Practice JEP@iiste.org
Journal of Law, Policy and Globalization JLPG@iiste.org Global knowledge sharing:
New Media and Mass Communication NMMC@iiste.org EBSCO, Index Copernicus, Ulrich's
Journal of Energy Technologies and Policy JETP@iiste.org Periodicals Directory, JournalTOCS, PKP
Historical Research Letter HRL@iiste.org Open Archives Harvester, Bielefeld
Academic Search Engine, Elektronische
Public Policy and Administration Research PPAR@iiste.org Zeitschriftenbibliothek EZB, Open J-Gate,
International Affairs and Global Strategy IAGS@iiste.org OCLC WorldCat, Universe Digtial Library ,
Research on Humanities and Social Sciences RHSS@iiste.org NewJour, Google Scholar.

Developing Country Studies DCS@iiste.org IISTE is member of CrossRef. All journals
Arts and Design Studies ADS@iiste.org have high IC Impact Factor Values (ICV).

11.review of kanban planning and execution in the context of lean manufacturing

More Related Content

What's hot (20)

Similar to 11.review of kanban planning and execution in the context of lean manufacturing (20)

More from Alexander Decker (20)

Recently uploaded (20)

11.review of kanban planning and execution in the context of lean manufacturing