361

Water System Design Manual December 2009 Page 229
Appendix E: Recommended Pumping Test Procedures
1.0 Introduction
This aquifer pumping test procedures document specifies the minimum pumping test procedures
that DOH considers sufficient for demonstrating that a new source is capable of providing a safe
and reliable yield of water for the water system. This pumping test procedures document was
prepared to provide Group A water systems with basic information suitable to develop an
approach to satisfy the source approval requirements in WAC 246-290-130 (3)(c)(iii) and (3)(d).
Information is presented to enable a water system to address DOH concerns regarding the most
commonly encountered aquifer conditions or hydrogeologic settings across the state. Situations
involving complex hydrogeolgic settings, however, may require a high level of expertise and
experience to adequately design and evaluate pumping tests for demonstrating source reliability.
Stand-alone pumping test procedures specifying the minimum steps DOH consider adequate are
presented at the end of this document. A discussion of the basic components of a pumping test is
also provided to assist with understanding the procedures presented in this document. The intent
of this document, however, is not to provide a detailed step-by-step approach for conducting or
analyzing a pumping test. Numerous references provide detailed, industry-accepted information
on designing the specifics of a pumping or aquifer test. A list of selected references is provided
at the end of Section 5.0 of this document.
The principal objective of the pumping test is to obtain adequate information for DOH to
evaluate whether a source is capable of reliably providing a safe yield of groundwater. This
objective differs somewhat from the Department of Ecology’s whose concern is focused on
overall protection of the aquifer. In establishing water rights, the Department of Ecology
evaluates withdrawals from all users and recharge to the aquifer, and considers future water
needs from the aquifer.
This procedures document is not intended to evaluate the aquifer as a water resource, but rather
to establish the ability of the source to meet the design pumping rate. Reliability considers the
ability of the source over time to meet normal conditions of operation, without adversely
affecting the water quality or quantity demands of the water system. The reliability of
groundwater yield requires that the pumping test results can be projected for some time into the
future. From DOH’s perspective, a properly conducted pumping test is the best basis from which
to judge a source’s current and future reliability. A pumping test can indicate lateral flow
boundaries, hydraulic continuity, constraints of fracture flow, and recharge. All of these can be
important factors in establishing reliability. From the water system’s perspective, the pumping
test is the best method by which to size and establish the optimal depth setting of the pump, as
well as, establish water system storage and operational needs. Proper pump sizing and depth
selection can provide considerable savings to a water system over the lifetime of the well,
through reduced power consumption and maintenance costs.

December 2009 Water System Design Manual
WAC 246-290-130(c)(iii) states that one acceptable approach for demonstrating source
reliability is to conduct a pumping test at the maximum design rate and duration. For DOH to
make a source reliability assessment, Section 7.3 and Appendix F specify the pumping test and
hydraulic parameter information that should be submitted to DOH in a project report.
Those information requests pertaining to the pumping test portion of the report are summarized
below:
x Measurements of the static water level prior to pumping (in the test well and observation
wells, if any);
x All water level data for both the pumping and recovery phases of the pumping test;
x Graphical presentations of the data, as appropriate;
x Transmissivity, saturated thickness, and hydraulic conductivity values/calculations for the
producing aquifer;
x Storage coefficient and specific yield for the producing aquifer;
x Delineation of the 6-month, 1-, 5-, and 10-year time-of-travel zones for each well;
x Identification of any hydraulic connection with surface water; and
x Conveyance of pumped water.
This document is divided into three main sections.
1. Section 2.0 discusses the rationale of DOH basic pumping test procedures, and the
general approach for a water system to use when determining a pumping test protocol for
obtaining DOH new source approval. This is followed by a discussion of special aquifer
settings DOH has identified as having greater potential for concern regarding water
quality and the ability of the aquifer to provide a reliable source of water. Section 3.0 also
describes the basic pumping test requirements, provides the rationale behind their
selection, and presents a flow chart for a water system to follow for selecting a pumping
test.
2. Section 4.0 discusses what to do if the test is improperly conducted or goes wrong, and at
what point the test would probably not produce adequate data for DOH to conduct a
source reliability evaluation.
3. Section 5.0 discusses pumping test components and defines terms used throughout this
document.
The stand-alone pumping test procedures for each of the basic pumping tests are provided at the
end of this document. These procedures summarize the basic instructions for the step drawdown
and constant rate discharge-pumping test, including specific instructions for sources with
concern for saltwater intrusion.

2.0 Basic Pumping Test Approach
Various aquifer settings can be encountered when evaluating source reliability. For most settings,
source reliability will be defined sufficiently by conducting one or two basic pumping tests. If
necessary, adjustments can be made to the basic pumping test to address aquifer settings needing
more rigorous data collection and analysis.
Under WAC 246-290-130(c)(iii), DOH requires that a minimum of two components be
addressed when determining whether the source will be able to produce a reliable groundwater
yield. The first component is to determine the pump size and depth setting appropriate for the
aquifer and well. In most cases, this will require that a step drawdown test be conducted. The
second component is to determine whether this pumping rate can be maintained for some time
into the future. This test of reliability is accomplished by conducting a constant rate discharge
test. Under certain conditions, a single test—either a step drawdown or constant rate test—may
be adequate.
What is a step drawdown test? The step drawdown test is similar to the constant-rate discharge
test in many respects. The major difference being that the step drawdown test consists of several
short-duration, constant-rate discharge tests—each run at a progressively higher pumping rate.
The minimum suggested step drawdown test consists of at least four different pumping rates,
each conducted for a minimum duration of 60 minutes. It is important, however, to run the initial
step long enough to establish that the effects of well storage have dissipated. The remaining steps
should each be run for the same duration as the initial step.
This step drawdown test provides a range of specific capacities for the well and is therefore, the
most reliable method for determining the pump size and setting. This test produces minimal
aquifer information, however, and will likely not identify impermeable boundaries, recharge
boundaries, interferences from other wells, or conditions of groundwater under the influence of
surface water, unless these conditions exist in very close proximity to the well being tested.
In most cases, a step drawdown test would be recommended to establish the optimal pumping
rate and depth for water system operation and to determine the pumping rate at which the
constant rate discharge test should be conducted. As mentioned, the step drawdown test produces
minimal information regarding aquifer characteristics and generally does not involve observation
wells. Therefore, where information on long-term productivity is critical or lacking, a constant
rate discharge test is needed.
The following paragraphs provide the basic pumping test recommendations for water systems
seeking new source approval or water system expansion where an existing source is utilized.
Information is also provided about DOH approaches and concerns to be addressed when the
aquifer response to pumping is anticipated to differ from a “standard” setting. “Standard” applies
to a wide range of conditions that could be encountered in source development. For the pumping
test requirements, a standard setting is defined as one in which

water quality and water reliability concerns are expected to be minimal. Within the standard
setting, the results of the pumping test could indicate the presence of flow boundaries
(impermeable or recharge) and that the source is in direct hydraulic connection with surface
water. Encountering these conditions during a pumping test does not necessarily indicate that
there are concerns from a water quality or a source reliability standpoint.
Table 1 in this Appendix has the hydraulic parameters that can be determined directly from the
pumping tests or a pumping test measurement component. Some parameters may be determined
in more than one manner. To determine all of the requested reporting information, however, it is
necessary to collect data during all aspects of a pumping test.
A pumping test is likely necessary under either of the following situations: 1) new source
approval or expansion of an existing water system, and 2) source capacity may be in question
(WAC 246-290-130(c)(iii)). Table 2 presents the pumping test recommendations for the aquifer
settings most likely to be encountered during development of a new source. In most cases, an
initial step drawdown test is recommended. There is only one condition where the step
drawdown test is not believed advisable. This condition occurs in standard aquifer settings where
adequate hydrogeological information exists to establish a sustainable pumping rate. This
situation could include a new source that will be used in a multiple well, paired well, or tandem
well configuration.
Figure 1 is a flow chart, which can be used to establish the appropriate pumping test, and to
identify those concerns to be addressed in a report sent to DOH. As an initial step, a water
system would be expected to review any existing hydrogeologic information to assist in
identifying any concerns which careful pumping test design could address. In many situations,
including standard aquifer settings and any areas of existing water quality or quantity concerns, a
water system would be expected to conduct at a minimum, a four-point step drawdown test. This
would be followed by a minimum, 24-hour constant rate discharge test with a minimum of 4
hours of stabilized drawdown data and completed with the collection of recovery data. The
constant rate discharge test would be conducted at the pump settings determined from the step
drawdown test and after aquifer recovery from the test. As a general rule, the aquifer should be
allowed to recover to within 95 percent of the static water level as measured prior to conducting
the step drawdown test. In situations common to small water systems, where a low demand
source is completed in a high productivity aquifer, it is expected that running the final step of the
step drawdown test until 4 hours of stabilized drawdown data have been collected will be
sufficient to establish source reliability. An example of this situation is a small water system with
a source completed in a high flow aquifer where drawdown stabilization would be expected to
occur quite rapidly.

Table 1: Data Provided by Pumping Test and Drawdown Measurements
Step Drawdown Test Constant Rate Test Recovery Data
Observation
Wells Data
Well Efficiency,
Pumping Rate (Q),
Transmissivity (T),
Specific Capacity (sc),
Yield
T, sc, Hydraulic
Conductivity (K), Yield
T, S S
Definitions Comments
Pumping Rate (Q) = gallons per minute
[gpm]
None
Yield = volume/time [gpm] None
Specific Capacity (sc) = yield/drawdown
[gpm/ft]
Allows well yields to be calculated at various
drawdown levels. This information is needed to
determine the maximum yield of the well and
can be used to examine the economics of well
operation at a given yield.
Transmissivity (T) = K*b [gpd/ft], (K =
hydraulic conductivity [gal/day/ft2
] and b =
aquifer thickness [ft])
Transmissivity can also be calculated from the
pumping test graphical solution using either the
Nonequilibrium Well Equation or the Modified
Nonequilibrium Equation. This value provides a
measure of how much water will move through
the aquifer as defined by a 1-ft wide vertical strip
extending through the full, saturated thickness of
the aquifer, under a hydraulic gradient of 1.
Coefficient of Storage (S) = [dimensionless],
can be calculated directly from the pumping
test graphical solution using either the
Nonequilibrium Well Equation or the
Modified Nonequilibrium Equation
This provides a measure of how much water can
be pumped or drained from the aquifer per unit
of aquifer storage area per unit change in head.
This value can only be calculated if observation
wells are incorporated into the pumping test. If
no observation wells; for a confined aquifer, a
value of sc = 5 x 10-4
may be used; for an
unconfined aquifer, a value of sc = 0.1 may be
assumed for calculations of well performance
and interference between wells.
Well Efficiency = theoretical
drawdown/actual drawdown [dimensionless],
expressed as a percent
Highly inefficient wells may or may not be
something that can be addressed. This
information can be very valuable if additional
wells are planned or can indicate that the well
would benefit from further or re-development.

Table 2: Aquifer Settings and Appropriate Tests
Setting
Description
Step Drawdown
Test
Constant Rate
Test
Recovery Data Observation
Wells
Standard Aquifer Setting
No Expected
Problems Or
Concerns With
Aquifer
Productivity
Yes1
(recommended)
Yes
(optional)
Yes
(recommended)
Should be used
if available
Special Aquifer Settings (at Q established by step drawdown test)
Low Flow
Conditions
Yes Yes Yes No
Fracture Flow Yes Yes Yes
Should be used
if available
Aquifer Of
Limited Areal
Extent
Yes Yes Yes
Should be used
if available
Saltwater Intrusion
Potential
Yes Yes Yes
Should be used
if available
Multiple
Wells/Tandem
Wells
Not Necessary New well only Yes Yes
1
In settings of a high productivity aquifer, low demand source, and no water quality issues; to
demonstrate source reliability, the final step should be run until four hours of stabilized
drawdown data have been collected and well recovery should be measured. Under these
circumstances only, a constant rate test is unnecessary.
How to set pumping rate (Q) for
step drawdown discharge test:
1. Set Q as follows:
Use the maximum design
pumping rate as Q for the 3rd
step. Multiply this value by
0.5, 0.75, and 1.25 to obtain
Q for the 1st
, 2nd
and 4th
steps, respectively.
How to set pumping rate (Q) for
constant rate discharge test:
Method (in order of preference)
1. Conduct step drawdown test
to establish optimal Q, or if
step drawdown test is not
necessary
a. use maximum design pumping
rate.
b. check with other aquifer test
results conducted in the area.

Is the source in area of known
reliability concerns due to: water
quality (salt water intrusion or
contamination) or productivity
(e.g., low flow aquifer or fractured
flow)?
Is the source in area of known
reliability concerns due to: water
quality (salt water intrusion or
contamination) or productivity
(e.g., low flow aquifer or fractured
flow)?
Conduct a step drawdown
test & constant rate discharge
test; report to DOH should
address specific concerns
identified in Sections 1 & 3 of
Pumping Test Procedures
Conduct a step drawdown
test & constant rate discharge
test; report to DOH should
address specific concerns
identified in Sections 1 & 3 of
Pumping Test Procedures
Review well log for
potential productivity concerns,
such as thin water bearing
zone or well screen completed
in low conductivity geologic
materials.
Review well log for
potential productivity concerns,
such as thin water bearing
zone or well screen completed
in low conductivity geologic
materials.
Is there a well log?
Is there a well log?
Is source in a high yield/low
productivity setting?
Is source in a high yield/low
productivity setting?
Run step drawdown and constant
rate discharge pumping test.
Prepare report and send to DOH.
Run step drawdown and constant
rate discharge pumping test.
Prepare report and send to DOH.
Extend last step of step drawdown
test for at least an additional 4 hours.
Were 4 hours of stabilized
drawdown collected?
Extend last step of step drawdown
test for at least an additional 4 hours.
Were 4 hours of stabilized
drawdown collected?
Pumping test
complete. Prepare
Report and send
to DOH.
Pumping test
complete. Prepare
Report and send
to DOH.
Yes
Yes
No
No
No
Yes
Yes
No Yes
Figure 1
PUMPING TEST
PROCESS FLOW CHART
Run constant rate
discharge test. Prepare
report and send to DOH
Run constant rate
discharge test. Prepare
report and send to DOH
No

3.0 Pumping Test Concerns in Special Aquifer Settings
Several aquifer settings have been identified as having a greater potential for reliability concerns
and were presented on Table 2. Reliability concerns include both water quality concerns (such as
high chloride levels or other contaminants) and water quantity concerns (such as seasonal
availability or aquifer continuity). Typically, these aquifer settings do not require that different
types of pumping tests be conducted. However, they may require a longer test or more rigorous
analysis of certain aspects of the pumping test results. Because of the greater difficulty and
complexity in pumping test design and evaluation presented by these settings, consultation with
an experienced hydrogeologist or engineer may be advisable. DOH information elements and
concerns unique to these conditions are discussed below.
Low Flow Conditions
Low flow conditions could be encountered for wells completed in materials of low hydraulic
conductivity such as silts, sandy clays or sandy silts, weathered sandstone, and other weathered
consolidated materials. In these cases, the ability of the well and aquifer to produce at the
required pumping rate is of concern, not necessarily the quantity of water available. Turbulent
flow induced during pumping can result in a significant decrease in aquifer performance with
increasing pumping rate. Therefore, a step drawdown test is recommended to determine the
specific capacity, yield, and the optimal pump settings.
Because it is unlikely that boundary conditions would be encountered in low-flow conditions
during the step drawdown test, a constant rate discharge test is also recommended. The
maximum pump setting, as determined from the step drawdown test, should be used for the
constant rate discharge test. The constant rate discharge test should be run after the static water
level has stabilized at initial levels (following the step drawdown test recovery period). DOH is
interested in an evaluation of aquifer stabilization and constant-rate discharge test drawdown
effects to demonstrate longer-term reliability of the source. Observation wells are not necessary,
even if available, because effects of pumping in low-flow conditions are typically not far
reaching.
Fracture Flow
DOH concern for fractured material is based on whether the source is adequately evaluated to
demonstrate that pumping requirements can be met over the long term. Typically, sources
completed in bedrock composed of shale, basalt, granite or any consolidated material can have
fractured flow concerns. The continuity of fractures can vary significantly within an aquifer and
affect its ability to provide water in a consistent manner. This difficulty may be compounded by
a lack of seasonal source reliability. Recharge may vary seasonally and cause production
problems in low flow periods (low water level and low recharge). During these periods excessive
drawdown may occur. Because of these concerns, each source must demonstrate an ability to
provide a safe and reliable yield.

The reliability of an individual source in the aquifer does not define the reliability of other
sources in this type of setting. A step drawdown test is recommended to determine the optimal
pump setting for consistent yield. A constant rate discharge test is also recommended to
demonstrate long-term reliability. The constant rate discharge test should be conducted at the
optimal pumping rate and pump depth setting indicated by the step drawdown test results.
Restrictive conditions identified by the pumping test could include lack of stabilization, for
example, drawdown continues to increase with time. This could signify that recharge does not
occur within the aquifer at a rate sufficient to maintain consistent discharge at the desired
pumping rate. It is also possible that the rate of drawdown decreases with time. This effect would
suggest that a recharge boundary was encountered and that the source could be capable of
producing a reliable yield. Observation wells should be used if available, because measurement
of drawdown in these wells can provide an indication of the extensiveness and interconnectivity
of the fractures. Selection of appropriate observation wells in a fractured setting, however, can be
problematic and may warrant input from a hydrogeologist or engineer experienced in pumping
test design.
Aquifer of Limited Areal Extent
This aquifer condition presents the same type of concerns as fracture flow. Although wells in this
setting may initially be able to provide a reliable source of water, because of limited areal extent
and recharge capacity, these aquifers may be unable to produce over the long term at the desired
pumping rate. These aquifers are commonly made up of highly variable material, which may also
show significant variation in its ability to transmit water. For this reason, a step drawdown test is
recommended to determine the pump depth and settings. Again, because of the often variable
nature of the geologic materials throughout the water-bearing zone, a constant rate discharge test
is recommended to identify any recharge boundaries or impermeable boundaries. The
characteristics of the data and their significance are similar to those presented above in the
discussion for fractured flow. If available, observation wells should be used so that the
coefficient of storage can be determined as accurately as possible.
Saltwater Intrusion
In addition to demonstrating that the well and aquifer are capable of producing a reliable yield of
groundwater, an assessment of the potential for inducing saltwater intrusion in the pumping well
or nearby wells is also requested. The pumping test recommendations are identical to those
previously discussed in the special aquifer settings. Initially, the pump settings are determined by
the results of a step drawdown test, which is followed with a constant rate discharge test to assess
the longer-term reliability of the aquifer. Ideally, observation wells should be selected so that
they are positioned between the pumping well and the saltwater body. In situations where
observation wells are present but in less desirable locations, it is still recommended that those
wells be used to allow calculation of storage coefficient and other hydraulic parameters data. In
areas where the potential for saltwater intrusion is high, it is also important to evaluate tidal
influences prior to conducting the pumping test. This is also a situation where because of the
complexity of pumping test design and evaluation, input from an experienced hydrogeologist or
engineer may be beneficial.

Pumping tests in potential saltwater intrusion areas differ from the other aquifer settings
primarily in that, water quality tests for chloride and specific conductance are needed in both the
pumped wells and observation wells at specific intervals throughout the aquifer test period.
These water quality indicators are monitored in the field using instruments specific to these
parameters. Water quality measurements are to be made to determine whether concentrations are
increasing, potentially signifying that saltwater is being drawn towards the pumping well.
Stabilization in drawdown or the presence of a recharge boundary without an associated increase
in chloride levels in the pumping well or observation wells would be favorable in demonstrating
source reliability.
Multiple Wells/Tandem Wells
This setting refers to two or more wells completed in the same aquifer that will be pumped either
cyclically or concurrently. DOH’s primary concern in this setting is whether the new well
interferes with other wells pumped by the water system or with aquifer recovery. Because of the
variety of water system needs addressed by adding an additional well(s), it is recommended that
the purveyor contact DOH to discuss a pumping test approach prior to actually conducting the
test. This is also a situation where because of the complexity of pumping test design and
evaluation, input from an experienced hydrogeologist or engineer may be beneficial.
In situations where a pumping test has been conducted for an existing well and data was also
collected from an observation well(s), the potential for well interference due to adding an
additional well can be determined using a distance-drawdown graph and evaluating additive
drawdown for all pumping wells. In many instances, conducting an additional pumping test
exclusively on the new well would provide little new information beyond validating the findings
of the initial pumping test, unless it was conducted at the total concurrent pumping rate. In
general, an evaluation of potential well interference for either cyclical or concurrent pumping can
be determined using this approach. If an observation well was not used during the pumping test
the same approach can be used, however, the results will likely be less accurate in predicting
well interference.
Depending upon the new maximum design pumping rate and desired yield, however, this
approach alone can fall short in demonstrating the ability of the aquifer to recover under the new
pumping configuration. Therefore, in settings where the new maximum design pumping rate
would significantly increase the required aquifer yield, DOH may request that a constant rate
pumping test be conducted using the proposed maximum design pumping rate for all wells that
would be concurrently pumped. For this reason, DOH considers each source approval in a
multiple well/tandem well setting to be a unique situation and DOH should be consulted during
the pumping test development process.
4.0 When Problems With Pumping Tests Occur
Tables 3 and 4 provide information regarding some of the more typical problems that can occur
when conducting the step drawdown and constant rate discharge pumping test, respectively. The
significance of these problems varies according to how far into the test they occur and to what
degree they are caused by the aquifer responding to the pumping test or are due to human error.

These potential problems are discussed in terms of, at what point would DOH question the
ability of the pumping test to demonstrate source reliability. This will vary, however, depending
on how much information has been obtained from the pumping test and what the information
provides towards establishing source reliability. As indicated in the tables, not all problems or
situations would result in a recommendation that the pumping test be repeated.
5.0 Pumping Test Components
The following components require consideration when designing a pumping test. The
information presented is not intended to be a resource on all aspects of pumping tests, but rather
to provide an idea of the considerations necessary to plan a pumping test and to supplement the
information presented in the individual policies presented later in this procedures document.
Duration
The duration of the pumping test is specified within each of the individual pumping test
methodologies provided later in this appendix. It is very important, regardless of whether the
pumping test conducted is constant-rate or step-drawdown, that the pumping rate is held as
constant as possible during each phase of a pumping test. The step-drawdown procedure should
be a minimum of four, 60-minute constant rate tests, with each run using an increasingly higher
flow rate. It is important to run the initial step, however, for a duration long enough to
demonstrate that well storage effects have dissipated. Each of the remaining three steps should
be run for a length of time identical to the initial step. The pumping test duration for the constant
rate discharge test is a minimum of 24 hours.
Pumping Rate
Fluctuations in pumping rate make the test analysis very difficult and raise questions as to
whether deviations in the data are actually a result of flow boundaries or other hydrogeologic
features. Control of the pumping rate is often best accomplished by accurately measuring and
controlling the discharge rate. Consideration should be given to the type of pump used to conduct
the test. A pump driven by a gasoline engine which needs to run at full throttle in order to meet
the required pumping rate, may vary significantly in pumping rate. Using a pump with a large
enough capacity to meet the required pumping rate at ½ to . full throttle will produce a more
constant yield. Electric pumps are generally not subject to the same rate fluctuations as gasoline
powered pumps. A valve in the discharge line, ½ to ¾ open, allows for flexibility in adjusting
discharge rate if necessary. The pumping rate should be monitored every 10 to 15 minutes during
the first hour of pumping and throughout each phase of the step drawdown test. At later times,
the pumping rate should be monitored every 2-hours and the rate maintained within 10 percent of
its starting value.

Table 3: Step Drawdown Test Problems and Their Significance
to Demonstrating Source Reliability
Problem Significance
Would Repeating Pumping
Test Be Advised?
Discharge rate varies
during pumping by more
than 10%.
Stabilize discharge rate as quickly as
possible. Discharge rate fluctuations make
identification of optimal yield difficult.
Probably not, if it was only one of the
steps and the follow-up constant rate
discharge test was conducted
adequately. Collection of recovery
data would also provide adequate
data.
Data collection does not
occur at the minimum
specified intervals.
Without data collection at a sufficient
frequency, it is very difficult to establish
what conditions may be affecting
groundwater flow.
Yes
Well is pumped dry
because pump was
placed too close to static
water level.
For the pumping tests, the pump should be
placed as far below the static water level as
possible without placing it within the
screened interval of the well. This allows the
maximum possible drawdown and maintains
some degree of well efficiency.
Yes.
Well is pumped dry
because the pumping
rate is unsustainable.
No additional higher rate steps are necessary
and the step drawdown test is complete at
this point.
Repeating the test at the same
pumping rate(s) would probably be
of little value. Repeating the test at a
lower rate would be advisable, if
lower pumping rate drawdown data
was not obtained.
Drawdown does not
stabilize and shows
continued increase.
This is likely to be the case for the step
drawdown tests. The tests are short enough
that drawdown is unlikely to stabilize,
unless low demand source in a highly
productive aquifer.
No, the test would not need to be
repeated. If a water system extended
the final step and did not achieve 4
hours of stabilization, then a constant
rate discharge test should be
conducted.
Drawdown does not
stabilize and decreases at
some point through the
end of the pumping test.
This may indicate a recharge boundary has
been encountered and would not signify a
problem. It may indicate that a surface water
body has been encountered and that the
source would be designated as groundwater
under the influence of surface water (GWI).
It may also indicate that the source is
located in or adjacent to a leaky aquifer.
The pumping test does not need to be
repeated. All of these conditions may
have implications for source
susceptibility and vulnerability, but
do not necessarily suggest a problem
for reliability.
Water never clears up
(stays turbid) during the
pumping test.
This may indicate that the well was
inadequately developed or that too coarse a
filter pack was placed around the well
screen.
Assuming the pumping test was
properly conducted, repeating the test
would not be necessary. Additional
well development may be necessary.
Water starts out clear,
but becomes turbid
during the pumping test.
This likely indicates that the well was
inadequately developed. It may also indicate
that groundwater of poorer quality or a
surface water body was encountered within
the well’s area of influence and that water
system modification may be necessary.
Pumping test would not need to be
repeated. Water system may want to
verify this problem as an ongoing
concern, however, by repeating the
pumping test and establishing its
constancy.

Table 4: Constant Rate Discharge Test Problems and Their Significance to
Demonstrating Source Reliability
Would Repeating Pumping Test
Be Advised?
Discharge rate
varies during
pumping by more
than 10%.
Stabilize discharge rate as quickly as
possible. Any conditions masked by the
flow rate variance may be visible in the
recovery data.
Yes, if rate fluctuated frequently by more
than 10% and recovery data was not
collected.
Data collection does
not occur at least at
the minimum
specified intervals.
Without data collection at sufficient
frequency, it is very difficult to
establish what aquifer conditions may
be affecting groundwater flow.
Yes
Well is pumped dry
because pump was
placed too close to
static water level.
For the pumping tests, the pump should
be placed as far below the static water
level as possible without placing it
within the screened interval of the well.
This allows the maximum possible
drawdown and maintains some degree
of well efficiency.
Yes, unless it occurred very late into the test
(for example, at 24 hours or later) and it is
apparent that drawdown was in the process
of stabilizing. In most cases, however, the
test would need to be repeated.
Well is pumped dry
because the
pumping rate is
unsustainable.
This may reflect that either the
pumping rate or duration needs to be
reduced.
Depends at what point in the test the well
was dewatered and the slope of the time
verses drawdown curve for the data that has
been collected. If pumping time was less
than 18 hours, the test will probably need to
be repeated.
Drawdown does not
stabilize and shows
continued increase.
There is no remedy, short of reducing
the pumping rate until equilibrium is
reached with recharge. The pumping
test should be completed with
collection of recovery data, as this may
be a particularly key component in
establishing source reliability.
This is very much a case-by-case situation.
If recovery is very slow, the pumping test
may need to be repeated at a lower pumping
rate to demonstrate source reliability.
Water levels do not
recover or exhibit
limited recovery
after pumping test.
This may be observed in conjunction
with continuous, excessive drawdown
during the pumping test. This could
indicate that the aquifer has a very
limited recharge area, the aquifer is of
small areal extent, or of limited
hydraulic continuity.
The pumping test has revealed significant
limitations of the aquifer and repeating the
pumping test would probably not provide
new information. Conducting the pumping
test at a lower rate may be necessary to
determine new storage and pumping
criteria.
Drawdown does not
stabilize and
decreases at some
point through the
end of the pumping
test.
This may indicate a recharge boundary
has been encountered and would not
signify a problem. It may indicate that a
surface water body has been
encountered and that the source would
designate as groundwater under the
influence of surface water (GWI).
The pumping test does not need to be
repeated.
Water never clears
up (stays turbid)
during the pumping
test.
This may indicate that the well was
inadequately developed or that too
coarse a filter pack was placed around
the well screen.
Assuming the pumping test was properly
conducted, the test would not need to be
repeated. Additional well development may
be necessary.

Would Repeating Pumping Test
Be Advised?
Water starts out
clear, but becomes
turbid during the
pumping test.
Although, this may indicate that the
well was inadequately developed, it
probably indicates that groundwater of
poorer quality or a surface water body
was encountered within the well’s area
of influence and that water system
modifications may be necessary.
Pumping test would not need to be repeated.
Water system may want to verify this
problem as an ongoing concern, however,
by repeating the pumping test and
establishing its constancy.
Observation Wells
Other wells in the vicinity and open to the same aquifer as the test well should be used as
observation wells, whenever possible. The use of observation wells greatly enhances the ability
to obtain more representative and accurate data during the test. Pre-test analysis of well depth
and distance can determine the best wells to use for observation. If the aquifer being evaluated is
confined, it may be useful to select an additional observation well completed within the
overlying unconfined aquifer to determine whether there is any leakage from the overlying
aquifer into the confined water system. For saltwater intrusion determinations, observation wells
positioned between the pumping well and saltwater body provide the most useful information.
Information collected from observation wells is desirable, however, regardless of whether well
positioning is optimal.
Stream Stage
If there is a stream near the well being tested, and the conceptual model or simulation suggests a
potential connection, the stage (depth and width) of that stream should be periodically monitored
for changes during the pumping test period. The relative size and distance of the surface water
body with respect to the proposed pumping rate should be considered when evaluating the
usefulness of conducting stream stage measurements.
Pre-pumping Phase
The well to be tested should be at its “normal” static water level prior to the test. Water level
measurements should be made at 24, 16, 12, 3, 2, and 1 hours prior to initiating pumping. Within
the hour immediately preceding pumping, water level measurements should be taken at 20-
minute intervals to establish any short-term trends in water level changes that may be occurring.
Barometric measurements of atmospheric pressure (inches of mercury) should be made as well.
These measurements will allow appropriate corrections to be applied to the drawdown data. In
settings where tidal influences may affect the pumping test results, measurements should be
made at a frequency sufficient to correct the pumping test drawdown data for any observed tidal
influences.

Pumping Phase
After initiation of the pumping test (regardless of pumping test method used), drawdown
measurements in the production and observation wells should be recorded according to the
schedule below. The greatest numbers of measurements are made within the first 100 minutes
when the water levels are changing rapidly. The time intervals given are suggested minimums;
more frequent measurements can assist with pumping test analysis and interpretation.
Time After Pumping
Started For Constant Rate
Test And After Pump Shut
Off For Recovery
Time Intervals To
Measure Water
Levels And
Record Data
0 to 10 minutes 1 minute
10 to 60 minutes 5 minutes
Recovery Phase
Water level measurements obtained during the recovery phase are of equal or greater importance
than those collected during the pumping phase because it can confirm any disturbances to flow.
In addition, unlike the pumping phase where variation in discharge rate can affect the
observations, the recovery phase is not subject to induced variations and can provide more
reliable information. Water level measurements made during the recovery phase of the aquifer
after the pump has been turned off should be taken at the same frequency as the drawdown
measurements during the pumping phase. Do not remove the pump until the test is completely
done, including the recovery phase. Measurements should commence immediately upon pump
shut down and continue for the same duration as the pumping phase, or until the water levels
have reached 95 percent of the initial, pre-pumping static water level. A check valve should be
used to prevent backflow of water in the riser pipe into the well, which could result in unreliable
recovery data.
Stabilization
Stabilization is defined as less than 0.1 foot of drawdown fluctuation/hour in 4 hours of
drawdown measurement.
Measurement Considerations
Water level measurements should be determined to the nearest 0.01 foot. Because of the
frequency of measurement required during the initial portion of the test, electronic water level
indicators marked in tenths and hundredths of a foot should be used. Data loggers and pressure
transducers provide the most accurate measurements and are the easiest to use after initial setup,
although, they can add considerable expense to the test.

Conveyance of Pumped Water
There is no fixed rule on how far the water produced during the pumping test should be
discharged from the vicinity of the well. It is best to pipe the water outside of the area likely be
influenced by the pumping test. The objective of conveying pumped water as far from the site as
possible is to minimize the possibility of artificially recharging the aquifer and producing an
erroneous pumping test or at least affecting the later stages of the test. This is particularly
important when conducting pumping tests in shallow unconfined aquifer settings. Considerations
for determining a suitable distance include:
x Is the aquifer confined? If so, less distance will be necessary.
x The duration of the pumping test: the shorter the test, the less distance necessary.
x Depth to water and nature of geologic materials overlying the water producing materials:
the greater the depth to water, the less distance necessary; and, the more transmissive the
aquifer materials, the greater distance necessary.
x If at all possible, do not discharge conveyed water between the pumping test well and any
observation wells or any suspected flow boundaries.
References
The following is an incomplete list of references that provide information and methodologies
suitable for designing and analyzing a pumping test.
American Society for Testing and Materials (ASTM). 1997. D4043-96 Standard Guide for
Selection of Aquifer Test-Method in Determining of Hydraulic Properties by Well
Techniques.
Dawson, K. J., and Istok, J. D., 1991. Aquifer Testing, Design and Analysis of Pumping and Slug
Tests. Lewis Publishers, Inc. 121 South Main Street, Chelsea, Michigan, 48118.
Driscoll, F.G. 1986. Groundwater and Wells. Published by Johnson Division, St. Paul,
Minnesota 55112.
U.S. Geological Survey (USGS). 1983. Basic Ground-Water Hydrology, Water Supply Paper
2220. United States Government Printing Office.

DOH Step Drawdown Pumping Test Procedure
Objective
To evaluate well performance and determine the specific capacity of the well, aquifer
transmissivity, and yield. This information will allow a determination of the optimal pump
settings (depth and pumping rate) in the well.
Elements
1. It is recommended that a qualified water professional oversee testing of the well and
review data analysis and interpretations.
2. An access port to allow depth to water measurements, as described in WAC 173-160-
355, must be installed and maintained, if not already present.
3. The step drawdown test should consist of a minimum of four consecutive constant rate
discharge steps, with each step utilizing a higher pumping rate. Each step should be
conducted for at least 60 minutes. Some water systems may be eligible to conduct the last
step of the step drawdown test according to Step 8.
4. The step drawdown test should utilize the maximum design pumping rate as the third
step. The remaining pumping rates should be determined by multiplying the maximum
design rate by 0.50, 0.75, and 1.25.
5. Drawdown should be measured in the pumped well at least at the frequency given below:
Time After Pumping Started Time Intervals
600 to 1,440 minutes 120 minutes
6. Water samples must be collected from the source using proper sampling procedures and
analyzed by an accredited laboratory (WAC 246-290-130(3)(g)), unless a constant rate
discharge test will be conducted. Water samples should be taken within the last 15
minutes of pumping and must be analyzed for the following water quality parameters:

Group A Water System Type
Community
Nontransient
Noncommunity
Transient
Noncommunity
Bacti/Col Bacti/Col Bacti/Col
IOCs IOCs IOCs
VOCs VOCs VOCs
SOCs SOCs --
Rad -- --
x Bacteriological/coliform (Bacti/Col).
x Inorganic chemicals (IOCs).
x Volatile organic chemicals (VOCs).
x Radionuclide tests.
x Synthetic organic chemicals (SOCs); unless the source qualifies for a waiver,
exempting the source from analysis of all or a partial list of SOCs.
7. Recovery should be measured beginning at the end of the last step and measured until the
water level has returned to within 95 percent of the initial, pre-pumping static water level.
Measurement frequency should conform to the specifications above. The pump should
not be removed until the water level has returned to 95 percent of the pre-pumping static
water level.
8. Applicable to only some water systems. Low water demand sources, which are completed
in high productivity aquifers may continue to record drawdown measurements during the
last step until stabilization occurs. Measurements should be recorded at the frequency
specified in the above table. Stabilization means less than 0.1 foot of drawdown
fluctuation per hour in 4 hours of drawdown measurement. The data from this final step
should be used to plot the time versus drawdown graph and to determine transmissivity,
storage coefficient, and hydraulic conductivity. Generally, stabilization should occur
quickly in this type of aquifer setting. Water systems meeting these conditions and
running the last step to stabilization do not need to also run a minimum 24-hour constant
rate discharge test. In most instances, the appropriateness of this approach should be able
to be identified before running the step-drawdown test by reviewing previously
conducted tests in the area that are specific to the aquifer.
9. Determine the maximum pumping rate and pumping depth as established from the step
drawdown test. Use these values for conducting the constant rate discharge test, if the test
is applicable.
10. When the pumping test is completed and if a constant rate discharge test will not be
conducted, the data should be compiled into a report and submitted to DOH. The project
report guidelines for a groundwater source of supply are in Section 7.3 and Appendix F.
Reporting guidelines specific to pumping tests include the following:

a. All data on pumping rates and water levels (including static water levels) from the
pumping test and recovery period, and appropriate graphical presentations of the data.
b. The report should determine the following hydraulic parameters; transmissivity or
coefficient of transmissibility, hydraulic conductivity or coefficient of permeability,
and storativity or coefficient of storage.
c. A map and description (¼, ¼, Section Township Range) accurately indicating the
well location, as well as the land surface elevation to the nearest foot above sea level.
Address and parcel number should also be provided.
d. Summary, conclusions, and recommendations from the engineer or hydrogeologist
regarding pump settings and source reliability
e. A well construction report (well log) for the pumping well and all observation wells.
f. Distance, to the nearest foot, from pumping well to all observation wells and a map
indicating all well locations.
g. A copy of all laboratory test results.

DOH Constant Rate Discharge Pumping Test Procedure
Objective
To determine the capability of the well and aquifer to provide a reliable yield of water at the
desired rate. Sources with the potential for seawater intrusion should also conduct the additional
elements provided at the end of this document.
Elements
1. It is recommended that a qualified water professional (hydrogeologist or engineer)
oversee testing of the well.
2. An access port to allow depth to water measurements, as described in WAC 173-160-
355, must be installed and maintained, if not already present.
3. The source should be pump tested at no less than the maximum rate determined from the
step drawdown test. The constant rate discharge test should not be conducted until after
the water levels in the aquifer have achieved at least 95 percent recovery from the step
drawdown test pre-pumping static water level conditions.
Note: Bailer tests, air lift tests, and slug tests are not acceptable. They do not sufficiently
stress the aquifer and are too limited in areal extent.
4. The duration of the constant rate discharge test should be a minimum of 24 hours. If, at
24 hours, four hours of stabilized drawdown have been observed, the pump may be shut
off and measurements of recovery begun. If stabilized drawdown has not been observed
within a total of 36 hours, the pump may be shut off and recovery measurements begun.
Stabilization is defined as a drop in water level of less than or equal to 0.1 feet per hour.
5. Drawdown should be measured in the pumped well at least at the frequency given below:
Time After Pumping Started Time Intervals
600 to 1,440 minutes 120 minutes
6. Drawdown in observation wells should be measured, if such wells are available and the
information is necessary. Table 2 in Appendix E provides information about aquifer
settings for which collection of information from observation wells is encouraged.
7. Water samples must be collected from the source using proper sampling procedures and
analyzed by an accredited laboratory (WAC 246-290-130(3)(g)), unless the samples were
collected during the step drawdown pumping test. Water samples must be taken within
the last 15 minutes of pumping and analyzed for the water quality parameters as follows:

Group A Water System Type
Community
Nontransient
Noncommunity)
Transient
Noncommunity
Bacti/Coli Bacti/Coli Bacti/Coli
IOCs IOCs IOCs
VOCs VOCs VOCs
SOCs SOCs --
Rad -- --
x Bacteriological/coliform (Bacti/Coli).
x Inorganic chemicals (IOCs).
x Volatile organic chemicals (VOCs).
x Radionuclide tests.
x Synthetic organic chemicals (SOCs); unless the source qualifies for a waiver,
exempting the source from analysis of all or a partial list of SOCs.
8. Pumping should be followed by collection of recovery data until 95 percent recovery of
the pre-pumping static water level has been achieved. Recovery measurements should be
made in the same manner and at the same frequency as drawdown measurements. To
facilitate accurate recovery data collection, the water system should incorporate backflow
check-valve(s) that prevents water within the riser pipe from flowing back into the well
when the pump is shut off.
9. When the pumping test is completed, the data should be compiled into a report and
submitted to DOH. The project report guidelines for a groundwater source of supply are
in Section 7.3 and Appendix F. Reporting guidelines specific to pumping tests include the
following:
a. All data on pumping rates and water levels (including static water levels) from the
pumping test and recovery period, and appropriate graphical presentations of the data.
b. The report should determine the following hydraulic parameters: transmissivity or
coefficient of transmissibility, hydraulic conductivity or coefficient of permeability,
and storativity or coefficient of storage
c. A map and description (¼, ¼, Section Township Range) accurately indicating the
well location, as well as the land surface elevation to the nearest foot above sea level.
Address and parcel number should also be provided.
d. Summary, conclusions, and recommendations regarding pump settings and source
reliability.
e. A well construction report (well log) for the pumping well and all observation wells.
f. Distance, to the nearest foot, from pumping well to all observation wells and a map
indicating all well locations.

g. A copy of all laboratory test results.
Additional Steps for Potential Seawater Intrusion Areas
a. For the source well (the well pumped during the aquifer test), chloride and conductivity
samples should be collected at the following intervals: one sample during the initial 30 to
60 minutes, one sample during the 6th hour (360 to 420 minutes), one sample during the
12th hour (720 to 780 minutes), and one sample within the last 15 minutes of the aquifer
test pumping phase.
b. For at least one observation well, two chloride and conductivity samples should be
collected, one base sample prior to initiation of the aquifer test and one sample upon
completion of recovery data collection. Any observation well sampled should be purged
of three well casing volumes prior to sample collection. Following collection of the base
sample, observation wells should be given adequate time to recover to static water level
prior to initiation of the aquifer test.
Note: It is recommended that a field test kit be used to monitor chloride levels within the
pumping well during the pumping phase.
In addition to the reporting requirements in Item 9 above, the following should also be included
in the report:
1. Tidal influence on the pumping well. Data on pumping water levels, chlorides, and tidal
fluctuations (corrected to point) should be plotted on a single graph with respect to time.
2. Potential for seawater intrusion into this or other seaward wells.

Pumping Test Data Collection Sheet
Water System ID: Owner: Well Tag No.:
DOH Source ID: Water System Name: Well Name:
Type of Test: Conducted By: Date:
Static Water Level (as measured from reference point): County:
Observation Wells? Well Elevation (MSL):
Distance of observation well (r) from pumped well (ft):
Time
Time (t) since
pumping
began
(min)
Depth to
Water
Level (ft)
Drawdown
(ft) t/r2
Pumping
Rate (Q)
(gpm) Comments

Recovery Data Collection Sheet
Water System ID: Owner: Well Tag No.:
DOH Source ID: Water System Name: Well Name:
Type of Test: Conducted By: Date:
Static Water Level (as measured from reference point): County:
Observation Wells? Well Elevation (MSL):
Distance of observation well (r) from pumped well (ft):
Time
Time (t)
since
pumping
began
(min)
Time (t’)
since
pumping
stopped
(min) t/t’
Depth to
Water
Level (ft)
Residual
Drawdown
(ft) Comments

361

More Related Content

What's hot (18)

Similar to 361 (20)

More from Usama Waly (20)

361