8085_architecture of microprocessor electricals .ppt
- 2. 2 Building Blocks of Processor Systems MEMORY DATAPATH CONTROL INPUT-OUTPUT CPU
- 3. 3 Processor System Architecture The typical processor system consists of: CPU (central processing unit) ALU (arithmetic-logic unit) Control Logic Registers, etc… Memory Input / Output interfaces Interconnections between these units: Address Bus Data Bus Control Bus
- 4. 4 Bus and CPU Bus: A shared group of wires used for communicating signals among devices • address bus: the device and the location within the device that is being accessed • data bus: the data value being communicated • control bus: describes the action on the address and data buses CPU: Core of the processor, where instructions are executed • High-level language: a = b + c • Assembly language: add r1 r2 r3 • Machine language: 0001001010111010101
- 5. 5 Memory and I/O Memory: Where instructions (programs) and data are stored • Organized in arrays of locations (addresses), each storing one byte (8 bits) in general • A read operation to a particular location always returns the last value stored in that location I/O devices: Enable system to interact with the world • Device interface (controller or adapter) hardware connects actual device to bus • The CPU views the I/O device registers just like memory that can be accessed over the bus. However, I/O registers are connected to external wires, device control logic, etc. • Reads may not return last value written • Writes may have side effects
- 7. 7 The 8085 Bus Structure The 8-bit 8085 CPU (or MPU – Micro Processing Unit) communicates with the other units using a 16-bit address bus, an 8-bit data bus and a control bus.
- 8. 8 The 8085 Bus Structure Address Bus Consists of 16 address lines: A0 – A15 Operates in unidirectional mode: The address bits are always sent from the MPU to peripheral devices, not reverse. 16 address lines are capable of addressing a total of 216 = 65,536 (64k) memory locations. Address locations: 0000 (hex) – FFFF (hex)
- 9. 9 The 8085 Bus Structure Data Bus Consists of 8 data lines: D0 – D7 Operates in bidirectional mode: The data bits are sent from the MPU to peripheral devices, as well as from the peripheral devices to the MPU. Data range: 00 (hex) – FF (hex) Control Bus Consists of various lines carrying the control signals such as read / write enable, flag bits.
- 10. 10 The 8085: CPU Internal Structure The internal architecture of the 8085 CPU is capable of performing the following operations: Store 8-bit data (Registers, Accumulator) Perform arithmetic and logic operations (ALU) Test for conditions (IF / THEN) Sequence the execution of instructions Store temporary data in RAM during execution
- 11. 11 The 8085: CPU Internal Structure Simplified block diagram
- 13. 13 The 8085: CPU Internal Structure Registers Six general purpose 8-bit registers: B, C, D, E, H, L They can also be combined as register pairs to perform 16-bit operations: BC, DE, HL Registers are programmable (data load, move, etc.) Accumulator Single 8-bit register that is part of the ALU ! Used for arithmetic / logic operations – the result is always stored in the accumulator.
- 14. 14 The 8085: CPU Internal Structure Flag Bits Indicate the result of condition tests. Carry, Zero, Sign, Parity, etc. Conditional operations (IF / THEN) are executed based on the condition of these flag bits. Program Counter (PC) Contains the memory address (16 bits) of the instruction that will be executed in the next step. Stack Pointer (SP): Reserved area of memory in RAM where temporary information may be stored. It holds address of most resent stack entry.
- 15. 15 Example: Memory Read Operation
- 16. 16 Example: Instruction Fetch Operation All instructions (program steps) are stored in memory. To run a program, the individual instructions must be read from the memory in sequence, and executed. Program counter puts the 16-bit memory address of the instruction on the address bus Control unit sends the Memory Read Enable signal to access the memory The 8-bit instruction stored in memory is placed on the data bus and transferred to the instruction decoder Instruction is decoded and executed
- 17. 17 Example: Instruction Fetch Operation
- 18. 18 Example: Instruction Fetch Operation
- 19. 19 INSTRUCTION SET OF MICROPROCESSOR 8085
- 20. • 8085 has 246 instructions. Each instruction of microprocessor 8085 consists of opcode & operand. Opcode tells about the type of operation while operand can be data (8 or 16 bit), address, registers, register pair, etc. 20
- 21. Addressing mode is format of specifying on operands Microprocessor has five addressing modes. 21
- 22. Types of Addressing modes • Addressing Modes of Microprocessor 8085 • Direct Addressing Register • Addressing Register Indirect • Addressing Immediate Addressing • Implied Addressing 22
- 23. Direct Addressing : Address appears after opcode of instruction • The address of operand is specified within instructionThese are 3 byte instructions.Byte 1 is opcode while byte 2 & 3 are of address. Example : LDA D500 HThis instruction will load accumulator with content of memory location D500 H. Example : STA 95FF H This instruction will store the content of accumulator to memory location 95FFH Instruction Byte 1Byte 2Byte 3LDA D500 HLDA00 D5Ins • tructionByte 1Byte 2Byte 3STA 95FF HSTAFF 95 • https://slideplayer.com/slide/6029325/ 23