A fuzzy logic controlled dc dc converter for an

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Special Issue: 12 | ICAESA - 2014 | Jun-2014, Available @ http://www.ijret.org 6
A FUZZY LOGIC CONTROLLED DC-DC CONVERTER FOR AN
ELECTROLYZER APPLICATION WITH A VOLTAGE DOUBLER
K.Shanthi1, U. Rajesh2, A. Mallikarjuna Prasad3
1EEE Department, St John’s College of Engineering and Technology, Yemmiganur, India
Abstract
This paper develops a fuzzy logic controlled dc-dc converter for an electrolyzer application with a voltage doubler. In general day
by day usage of power is increasing rapidly but the available resources are exhausting in the near future. Hence we are going for
the renewable energy system (RES). It converts the energy into heat or electricity. Electrolyzer is a part of a renewable energy
system which converters source power available into hydrogen for fuel cell. But electrolyzer lacks the ability to control the power
over rapid changes in input and load , hence a power conditioning system is required to connect the electrolyzer to a system dc bus
. Usually a dc-dc converter is used in the most of application .This project deals with the comparison of three soft switched dc-dc
converter configurations for an electrolyzer and design of two stage (ZVT boost followed by LCL series resonant converter) with
fuzzy logic control. The proposed model has a Zero Voltage switching(ZVS) technique which maintain the soft switching for
complete load range. This proposed model is developed and analyzed using MATLAB/Simulink Software and the simulation results
obtained justify the accuracy of proposed control technique.
Keywords: DC-DC converter, electrolyzer, fuzzy logic controller PI controller, SRC, ZVS, ZVT.
---------------------------------------------------------------------***-----------------------------------------------------------------
1. INTRODUCTION
The main drawback of the electrical system is storage .RES
in the form of hydrogen storage overcome the weakness of
battery based system. Hence an electrolyzer is needed to
convert the electricity into hydrogen. The ability to store
energy at times when the supply exceeds demands will be a
key to the effective utilization of renewable energy. Because
many renewable sources (e.g. wind, solar, tidal) are
intermittent in nature, storage is useful. The figure 1 shows
the schematic diagram of a RES.
The basic idea is to keep harvesting the energy resource at a
steady rate, regardless of the demand. Usually, this results in
the most efficient operation. If the demand is less than full
capacity, the excess is diverted into storage medium. in the
proposed we go for a hydrogen storage which utilizes excess
electric power to produce hydrogen and oxygen from water
by means of electrolysis. Energy can be retrieved by running
them back through a fuel cell.
Fig. 1 schematic of a renewable energy system
In this paper we develops a MATLAB/simulink model of
three soft-switched high-frequency transformer isolated dc-to-
dc converter configurations for electrolyzer. Firstly, we
compared the three switching configurations of a dc-dc
converter. Among them it is shown that LCL type series
resonant converter with capacitive output filter is suitable
for this application. Due to the wide variation in input
voltage and load current, no converter can maintain zero-voltage
switching (ZVS) for the complete operating range.
Therefore, a two-stage converter (ZVT boost converter
followed by LCL SRC with capacitive output filter) is
adapted. later a PI and FUZZY logic control was
implemented for a closed loop operation and simulation
results are compared.
2. NEED OF A DC-DC CONVERTER
To achieve proper voltage matching the main components of
the system should be connected to the DC-bus of RES via dc-dc
converter. The electrolyzer is interfaced by help of a step-down
DC/DC converter, while the fuel cell is connected by
help of a step-up DC/DC converter.
In principle, any basic power converter topology can be used
to design a power interface for a fuel cell and an electrolyzer.
Typically, these converters have a high-frequency voltage
transformer, which could also perform the function of
isolation. The main technology development trend here is to
reduce the power losses in the interface converters in order to
obtain the highest possible energy efficiency .The following
figure2 shows the need of a DC-DC converter.

_______________________________________________________________________________________
Fig 2 Energy exchange using dc-dc converter
3. POSSIBLE SOFT SWITCHING
CONFIGARATIONS FOR THE ELECTROLYZER
APPLICATION
Soft switching converters has many advantages over hard
switching converters .these soft switching converters had a
advantage of reduce voltage/current stress, reduce EMI,
reduced switching losses, and allow a greater high frequency
in high power applications. There are three major types of HF
transformer isolated soft switching converter configurations
possible: 1) voltage fed resonant converters 2) current fed
resonant converters and 3) fixed-frequency resonant transition
zero-voltage switching (ZVS) pulse width modulation (PWM)
bridge converters .but current fed resonant converters require
HF switches rated at 5–6 times the input voltage which
reduces the efficiency. Hence Voltage fed resonant converter
with fixed-frequency operation is adopted in this paper. the
six soft-switching converter configurations for the electrolyzer
application:
1) Fixed-frequency series resonant converter (SRC).
2) Fixed-frequency parallel resonant converter (PRC.)
3) Fixed-frequency series-parallel or LCC-type resonant
converter (SPRC).
4) Fixed-frequency LCL SRC with a capacitive output filter.
5) Fixed-frequency LCL SRC with an inductive output filter.
6) Fixed-frequency phase-shifted ZVS PWM full-bridge
converter.
Among the aforementioned six converter configurations, the
SRC and SPRC can operate with the ZVS, only for very
narrow variations in supply and load variations in the present
application. In the case of PRC, the inverter peak current does
not decrease much with reduction in the load current and there
is no coupling capacitor in series with the HF transformer.
Therefore, the first three configurations are not considered.
Table: 1 Comparison of Converters
Problems LCL SRC
with cap
filter
LCL SRC
with
inductive
filter
Phase
shifted
PWM
converter
ZVS range 100%load
to 10%load
minimum
input
voltage
100%load
to 10%load
minimum
input
voltage
100%load
to 10%load
minimum
input
voltage
Duty cycle
loss
Not present Present Present
Rectifier
ringing
Not present Present,
requires
snubber
Present,
requires
snubber
4. BLOCK DIAGRAM OF A EXISTED SYSTEMS
The following figure3 shows the block diagram of a existed
system. it consists renewable source input which was given
to ZVT boost converter from there it is converted into a high
frequency AC using LCL- SRC converter and its output was
coupled to a rectifier using HF step down transformer. The
DC output of the rectifier is used to feed the electrolyzer
plant
Fig 3 Block diagram of a existed system
5. BLOCK DIAGRAM OF PROPOSED SYSTEM
In this proposed system a voltage doubler is placed instead of
rectifier, as it performs the rectification and as well as
doubles the output voltage .
Vo = 2* Vout
Even though existing two stage boost converter system is
operating accurately ,for a wide changing load and input
sources time to time there is fluctuations in the output .The
following figure 4 shows the block diagram of a proposed
system.

_______________________________________________________________________________________
Fig 4 Block Diagram of A Proposed System
6. RESULTS AND DISCUSSIONS
MATLAB is a software package for computation in
engineering, science, and applied mathematics. It offers a
powerful programming language, excellent graphics, and a
wide range of expert knowledge. MATLAB is published by
and a trademark of The MathWorks, Inc.
6.1 MATLAB Model for a LCL-SRC with Inductive
Filter
The following figure5 shows the MATLAB model of a LCL-SRC
with an inductive output filter. And the figures 6, 7, 8
shows the input voltage ,voltage across Vab , output voltage
Vo .Their values are given as follows
Input voltage = 40V
Voltage across Vab = 40 V
Output voltage Vo = 54
Fig. 5. MATLAB model of a lcl-src with an inductive filter
0 2 4 6 8 10 12 14
x 10
4
-10
0
10
20
30
40
50
60
time
output voltage
Fig. 6. simulation result showing the output voltage Vo
9500 9600 9700 9800 9900 10000 10100 10200 10300 10400 10500
-50
-40
-30
-20
-10
0
10
20
30
40
50
time
voltage at vab
Fig. 7. Simulation result showing voltage vab
2.06 2.07 2.08 2.09 2.1 2.11 2.12 2.13
x 10
4
-400
-300
-200
-100
0
100
200
300
400
Fig. 8. Simulation result showing inductor current il
6.2 MATLAB Model for a Fixed-Frequency Phase-
Shifted ZVS PWM Full-Bridge Converter
The following figure 9 shows the MATLAB model of a
LCL-SRC with an inductive output filter. . And the figures
10, 11, 12 shows the input voltage ,voltage across Vab , output
voltage Vo .Their values are given as follows
Input voltage = 40V
Output voltage Vo = 54 V
Fig 9 MATLAB model of a fixed-frequency phase-shifted
ZVS PWM full-bridge converter
0 2 4 6 8 10 12
x 10
4
0
5
10
15
20
25
30
35
40
time
output voltage

_______________________________________________________________________________________
6 6.05 6.1 6.15 6.2 6.25 6.3
x 10
4
-50
-40
-30
-20
-10
0
10
20
30
40
50
3450 3500 3550 3600 3650 3700 3750 3800 3850 3900
-40
-20
0
20
40
60
80
time
inductor current
Fig. 12. Simulation result showing inductor current il
6.3 MATLAB Model for a LCL-SRC with
Capacitive Output Filter
The following figure 13 shows the MATLAB model of a
LCL-SRC with a capacitive output filter. And the figures 14,
15, 16 shows the input voltage ,voltage across Vab , output
Input voltage = 40V
Fig. 13. MATLAB model of a LCL-SRC with a capacitive
output filter
0 2 4 6 8 10 12
x 10
4
-20
0
20
40
60
time
output voltage
1.18 1.2 1.22 1.24 1.26 1.28 1.3 1.32 1.34
x 10
4
-6
-4
-2
0
2
4
6
time
voltage at vab
2250 2300 2350 2400 2450 2500 2550 2600 2650 2700 2750
-250
-200
-150
-100
-50
0
50
100
150
200
time
voltage at vab
Fig. 16. Simulation result showing inductor current
From the figures 6,10 and 14 it can be say that LCL-SRC
with capacitive output filter has a better performance as the
peak in the output voltage had reduced to a great extent. and
also it maintains the ZVS for changes .
6.4 MATLAB Model for a Two Stage (ZVT Boost
LCL-SRC) Approach
LCL SRC with capacitive output filter has better
performance compared to other configuration, it maintains
ZVS for wide change in input voltage. But for wide change
in input an extra resonant inductor is required. So a ZVT
boost converter is required to boost input. By using this
converter the complexity in simplifying the resonant
component can be reduced when compared to other
approach.
This approach not only achieves ZVS for all the switches but
also simplifies the design of Lr and Cs resonant components.
The following figure 17 shows the MATLAB model of ZVT
boost LCL-SRC with capacitive output filter. And the figures
18, 19, 20 shows the input voltage ,voltage across Vab , output
Input voltage = 40V

_______________________________________________________________________________________
Fig. 17. MATLAB model of a LCL-SRC with a capacitive
output filter
3.25 3.3 3.35 3.4 3.45 3.5 3.55
x 10
4
-150
-100
-50
0
50
100
150
time
vab
2.46 2.48 2.5 2.52 2.54 2.56 2.58 2.6 2.62 2.64
x 10
4
-400
-300
-200
-100
0
100
200
300
400
time
inductor current
0 0.5 1 1.5 2 2.5 3
x 10
5
0
20
40
60
80
100
120
140
160
180
200
time
output voltage
Fig. 20. Simulation result showing output voltage Vo
From the above figure 20 it can observe that smoot output
voltage is observed .hence by adopting the ZVT boost at the
input side the input is maintained to a constant value hence
there by reducing the swithing losses at the inverter
6.5 MATLAB Model for a PI Controller with
Voltage Doubler
The following figure 21 shows the two stage(ZVT boost
LCL-SRC ) with an voltage doubler and a PI controller. At
the input side a FUEL cell stack taken as the input source.
And the figures 23, 24, 25 shows the input voltage ,voltage
across Vab , output voltage Vo .Their values are given as
follows
Input voltage = 40V
Output voltage Vo = 120V
Fig. 21. MATLAB model of a pi controller with voltage
doubler
Fig. 22. MATLAB model of a subsystem of a PI controller
2000 4000 6000 8000 10000 12000 14000 16000 18000
-150
-100
-50
0
50
100
time
vab
Fig. 23. Simulation result showing voltage Vab

_______________________________________________________________________________________
0 2 4 6 8 10 12
x 10
4
-20
0
20
40
60
80
100
120
140
time
vo
Fig. 24. Simulation result showing output voltage Vo
0 2 4 6 8 10 12
x 10
4
-600
-400
-200
0
200
400
600
time
inductor current
6.6 MATLAB Model of a Fuzzy Logic System
The use of fuzzy logic is attractive for control systems since
it enables the use of multiple inputs. Fuzzy logic also enables
the description of the behavior of the controller using several
rules defined by a set of linguistic variables. Hence, FLC is a
promising tool for controlling complex, linguistic based
systems. The steps to implement the fuzzy logic controller is
1. Create the membership values (fuzzify).
2. Specify the rule table.
3. Determine your procedure for defuzzifying the result.
First we have to fuzzify the data or create membership values
for the data and put them into fuzzy sets. simply, we have to
divide each set of data into ranges.
The following figure 27 shows the two stage(ZVT boost
LCL-SRC ) with an voltage doubler and a Ffuzzy logic
controller. At the input side a FUEL cell stack taken as the
input source. And the figures 29, 30, 31 shows the input
voltage ,voltage across Vab , output voltage Vo .
Fig. 27. MATLAB model of a FUZZY controller with
voltage doubler
Fig. 28. MATLAB model of a subsystem of a FUZZY
controller
Fig. 29. fuzzy surface system
1000 2000 3000 4000 5000 6000 7000 8000
-100
-50
0
50
100
time
voltage across ab
0 2 4 6 8 10 12
x 10
4
-20
0
20
40
60
80
100
120
time
output voltage vo

_______________________________________________________________________________________
0 2 4 6 8 10 12
x 10
4
-500
-400
-300
-200
-100
0
100
200
300
400
In the above figure 27 a fuzzy logic controller was
implemented with mamdani fuzzy inference type.when
compared the results of PI and fuzzy controller from the
figures 24and 30 it can be shown that even low voltage
application also the fuzzy controller can reduce the output
distortions.And also it maintains the ZVS for all switches
reducing the switching losses.
fuell stack rating = 6KW-45V DC
no of cells = 65
voltage at Vab = 100 v
output voltage = 120 V
7. CONCLUSIONS
In this paper a fuzzy logic controlled DC-DC converter for an
electrolyzer application has been implemented using
MATLAB/simulink. Among available converter
configurations it is shown that the a ZVT BOOST along with
LCL –SRC converter is best one for the electrolyzer. To
reduce the output distortions a PI controller was kept in order
to reduce the steady state error. A voltage doubler introduced
in the circuit acts as both rectifier and as voltage doubler .the
simulation results are checked for both fuzzy and PI
controller. It is shown that by using fuzzy logic controlled
converter the conversion can be operated smoothly and
efficiently for electrolyzer application compared to the other
converters. And the output voltage range also doubled .
REFERENCES
[1] D. Shapiro, J. Duffy, M. Kimble, and M. Pien, “Solar-powered
regenerative PEM electrolyzer/fuel cell
system,” J. Solar Energy, vol. 79, pp. 544–550, 2005.
[2] X. Zhang, H. S.-H. Chung, X. Ruan, and A. Ioinovici,
“A ZCS full-bridge converter without voltage
overstress on the switches,” IEEE Trans.
PowerElectron., vol. 25, no. 3, pp. 686–698, Mar. 201
[3] D. S. Gautam and A. K. S. Bhat, “A two-stage soft-switched
converter for electrolyser application,” in
Proc. Nat. Power Syst. Conf., Mumbai, India, 2008,
pp. 524–528.
[4] A.K.S. Bhat, "Analysis and design of LCL-type
resonant converter", IEEE Trans. on Industrial
Electronics, vol. 41, no. 1, pp. 118-124, Feb. 1994.
[5] A.K.S. Bhat, "Analysis and design of a fixed
frequency LCL-type series resonant converter," IEEE
Trans. on Aerospace and Electronic Systems,vol. 31,
no. 1, Jan. 1995, 125-137.
[6] Ahmadi, P., Dincer, I., Rosen, M.A., 2013. Energy
and exergy analyses of hydrogen production via solar-boosted
ocean thermal energy conversion and PEM
electrolysis. International Journal of Hydrogen
Energy, 38 (4) : 1795- 1805.
[doi:10.1016/j.ijhydene.2012.11.025]
[7] Arriaga, L.G., Martinez, W., Cano, U., Blud, H.,
2007. Direct coupling of a solar-hydrogen system in
Mexico. International Journal of Hydrogen Energy,
32 (13): 2247- 2252.
[doi:10.1016/j.ijhydene.2006.10.067]
[8] Y. Jang and M. M. Jovanovic, “A new family of full-bridge
ZVS converters,” IEEE Trans. Power
Electron., vol. 19, no. 3, pp. 701–708, May 2004.
[9] H. Bodur and A. F. Bakan, “A new ZVT-PWM DC-DC
converter,” IEEE Trans. on Power Electr., vol.
17, no. 1, Jan. 2002, pp. 40-47.
[10] R. Streit and D. Tollik, “High efficiency telecom
rectifier using a novel soft-switched boost based input
current shaper”, IEEE INTELC Conf. Record, 1991,
pp.720-726.
[11] Ferraro, “An overview of low-loss snubber
technology for transistor converters,” in Proc. IEEE
Power Electron. Spec. Conf., 1982, pp.466–477.
[12] G. Hua, C. S. Leu, Y. Jiang, and F. C. Y. Lee, “Novel
zero-voltagetransition PWM converters,” IEEE Trans.
Power Electron., vol. 9, pp. 213–219, Mar. 1994.
601–606, Nov. 1994.
[13] D. S. Gautam and A. K. S. Bhat, “A two-stage soft-switched
converter for electrolyser application,” in
Proc. Nat. Power Syst. Conf., Mumbai, India, 2008,
pp. 524–528.

A fuzzy logic controlled dc dc converter for an

More Related Content

What's hot (18)

Viewers also liked (20)

Similar to A fuzzy logic controlled dc dc converter for an (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

A fuzzy logic controlled dc dc converter for an