A remote monitoring system for a three phase 10-kva switchable distribution transformer using zigbee wireless network

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 02 | Feb-2014, Available @ http://www.ijret.org 668
A REMOTE MONITORING SYSTEM FOR A THREE-PHASE 10-KVA
SWITCHABLE DISTRIBUTION TRANSFORMER USING ZIGBEE
WIRELESS NETWORK
S.Dinesh Kumar1
, R.Suresh Kumar2
, Dr.Rani Thottungal3
1
PG Student, EEE Department, Kumaraguru College of Technology, Tamil Nadu, India
2
Asst.Professor, EEE Department, Kumaraguru College of Technology, Tamil Nadu, India
3
Professor and Head, EEE Department, Kumaraguru College of Technology, Tamil Nadu, India
Abstract
A Remote Monitoring System plays an important role in many applications. This paper proposes an innovative design about the
development of remote monitoring system for a three-phase 10-kVA Switchable Distribution transformer with the help of a PIC
microcontroller and Zigbee-based Wireless device. The PIC microcontroller from microchip helps in controlling the switching
devices and monitoring the current, voltage and temperature of the transformer. The Zigbee-based wireless device is used as long
range wireless communication between the modules. The information is transmitted point by point using Zigbee transmitter and
receiver and is sent to the server module to check the state of the transformer. It has a data rate speed of 250 Kbps with minimum
power consumption and has a transmission distances range from 10 to 100m. The data transmission rate is higher than other
wireless systems. This is user friendly and can be achieved at low cost. This handles the transfer of parameters such as voltage,
current and temperature as digital data from current transducers, voltage transformers and from temperature sensors to the
server module through wireless communication. This system helps in reading sensor, controlling switches, monitoring and data
protection.
Key Words: Switchable Transformer, PIC Microcontroller and Zigbee
--------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
The Switchable distribution transformer was introduced
in the year 2000. This transformer similarly works like
conventional transformer but only main difference is that the
use of the switching devices to connect the tappings of the
primary and secondary windings of the transformer. If the
switching devices implemented, the new difficulty arises
such as how to control the switching devices, how to reduce
the copper and core losses of the transformer and how to
monitor the parameters without the displacement of the crew.
Reference [1] monitors the parameters with the help of local
area network and used an Atmel with built in CAN controller
for communication between modules and used the other
controller to perform averaging and FFT calculation [3].this
further enhances wiring for communication between the
modules and more controller makes the entire system more
complex and used Ethernet as a wired network for remote
monitoring. Uses of more controllers will make costs more to
the entire System and it will also make more difficulties for
the operator to identify the problems in the complex system.
As a solution to this Problem, some advantages can be
done through the use of this approach in the system i.e.
1. Monitoring purpose can be carried out at the
desirable range without the displacement of the crew.
2. Complication in the system can be reduced by using
the single microcontroller and wireless network.
Fig-1: Three-Phase 10-kVA Switchable Transformer
3. The system costs can be reduced effectively.
In the system, a wireless device called Zigbee is used as a
long range wireless communication between the modules and
has data protection at the desirable range within the modules.
It can be achieved at low cost and helps in long battery life in
the process. This handles the transfer of parameters to the
server module using Zigbee transmitter and receiver. It is a
standard-based technology for remote monitoring and

_______________________________________________________________________________________
control. It supports low data rate, low power consumption,
security and reliability. It allows nodes to find new routes
throughout the network if one route fails, making it a robust
wireless solution.
2. HARDWARE DESCRIPTION
2.1 PIC16F877A MICROCONTROLLER
The PIC is a family of Harvard architecture
microcontrollers made by Microchip Technology, derived
from the PIC1640. The name PIC initially referred to
"Programmable Interface Controller".
PICs are popular with both industrial developers and
hobbyists alike due to their low cost, wide availability, large
user base, extensive collection of application notes,
availability of low cost or free development tools, and serial
programming (and re-programming with flash memory)
capability.
It is 8-bit microcontroller compatible with any other PIC
devices. It features 200 ns instruction execution, 256 bytes
of EEPROM data memory, self programming, an ICD, 2
Comparators, 8 channels of 10-bit Analog-to-Digital(A/D)
converter, 2 capture/compare/PWM functions, synchronous
serial port that can be configured as either 3-wire SPI or 2-
wire I2C bus, a USART, and a Parallel Slave port.
Its Features are:
 High-Performance RISC CPU
 Operating speed: 20 MHz
 Operating voltage: 4.0-5.5V
 Industrial temperature range (-40° to +85°C)
 15 Interrupt Sources
 35 single-word instructions
 10 bit, 8 channel A/D converter
 Brown out reset
 Power saving sleep mode
 Programmable code protection
 All single-cycle instructions except for program
Branches (two-cycle)
2.2 Zigbee- based Wireless device
Zigbee is based on IEEE 802.15 standard used to create a
personal area network built from low power digital radios. It
often transmits data over longer distances by passing data
through intermediate devices to reach more distant ones. It
targeted at radio frequency applications that require long
battery life, low data rate and secure networking. Zigbee has
a data rate speed of 250 kbps best suited for single signal
transmission from an input device or sensor. Transmission
distances range from 10 to 100 meters line of sight,
depending upon power output and environmental
characteristics. The Zigbee specification is intended to be
simpler and less expensive than other WPANs, such as
Bluetooth. It is a low cost, low power wireless mesh
standard. The low cost allows the technology to be widely
used in wireless control and monitoring system applications.
Zigbee networks are secured by 128 bit symmetric
encryption keys and mesh networking in the Zigbee network
provides high reliability and a more extensive range. It can
operate in the industrial, scientific and medical radio band
but uses 2.4 GHz in most jurisdictions worldwide. The data
transmission rate varies from 20 Kilobits/second in the 868
MHz frequency band to 250 Kilobits/second in the 2.4 GHz
frequency band. It also supports both star and tree networks
every network must have one coordinator device, tasked with
its creation, the control of its parameters and basic
maintenance. Both trees and mesh allows the use of Zigbee
network to extend the communication at the network level.
3. ACQUISITION MODULE
In the process, the acquisition module is the most
significant module in the system will be discussed. This
acquisition module is used to control the switching devices
connected to the tappings of the primary and secondary side
of the transformer and used to sense and transfer the
following parameters. They are
1. Primary Voltage (for Phase A, B and C)
2. Secondary Voltage (for Phase A, B and C)
3. Primary Current (for Phase A, B and C)
4. Secondary Current (for Phase A, B and C)
5. Primary and Secondary Winding Temperature
In the system, the only one acquisition module is used
for the three phase transformer. This acquisition module is
used to control all the switching devices and to sense and
transfer the parameters of the transformer. The
microcontroller in the acquisition module used to control all
the switching devices and has ability to sense the parameters
of the transformer accurately. This will be the massive task
for the controller to handle the switching devices but
thinking of cost, this will be highly beneficial and it will be
easy to identify the problems in the system.
The design of the switching devices of one phase is
connected to the acquisition module is shown in the figure
2.this will be similar to other phases also. As in the figure 2,
there are each six switching devices are connected to the
tappings of the primary and secondary windings of each
phase to form a serial or parallel configuration .this
configuration can be achieved by turning ON or OFF the
corresponding switching devices as presented in the table I.
The implementation of the configuration is used to achieve
efficiency or used to reduce the core and copper losses of the
transformer. This implementation of the configuration helps
in achieving the better efficiency over the conventional
transformer. More information about the implementation of
the configuration to achieve better efficiency can be read out
in [5].

_______________________________________________________________________________________
In addition to turn the switching devices into ON/OFF
conditions, the microcontroller in the module helps in
performing the switching operations from series to parallel
Table –I: Switching Device States
Configuration SW1 SW2 SW3 SW4 SW5 SW6
Serial OFF ON OFF OFF ON OFF
Parallel ON OFF ON ON OFF ON
(or vice versa) at zero crossing of current to reduce transient
as an effect of switching. Zero crossing of primary voltage is
used to trigger the beginning of the sampling process through
hardware interruption inside the microcontroller. It also
senses the temperature of the windings with the help of the
analog temperature sensors. Performing this process, the real
time monitoring of the current and voltage signals are done
by the microcontroller used for the following purposes
 To determine the winding configurations and timing
for switching operations.
 To calculate the true RMS voltages and currents,
average power and losses.
 Protection against overloads and transients.
.
The processes data sent by the microcontroller will be
transmitted to the server module through wireless
communication.
4. REMOTE MONITORING
Remote monitoring of transformers has already been
widely known and implemented with various technologies.
Many approaches are developed to perform the remote
monitoring in the world through the use of network
connected to the internet.
Fig- 2: Acquisition Module Connected to One Phase of the Three-Phase 10-kVA Switchable Transformer

_______________________________________________________________________________________
In relation to this project, this was applied to the three-phase
10-kVA switchable distribution transformer. This
transformer has been previously developed to show an
increase in the efficiency through the use of special
configurations of windings called serial and parallel
configurations. The serial configuration is highly efficient at
low loads with higher number of turns and parallel
configuration is highly efficient at high loads with a low
number of turns of both the windings of the switchable
distribution transformer. These configurations are used to
increase efficiency by reducing core and copper losses of the
switchable distribution transformer.
In relation to this project, we designed a remote
monitoring system as shown in the fig.4 which is based on
PIC microcontroller present in the acquisition module used to
monitor and control the voltages, currents and temperatures
of the switchable distribution transformer and also used to
switch ON/OFF the switching devices depends upon the
configurations. Each phase data will be monitored for 10 secs
by the acquisition module and it will be transmitted to the
server module through Zigbee.
The Zigbee has a large coverage area up to 100m and has
a transmission data rate ranging from 20 Kbps to 250 Kbps
with minimum power consumption.
The Radio Frequency (RF) antenna used in the system is
tuned for selected frequency for data transmission. On the
receiver side, the receiver antenna used in the system
converts The RF signal into an electrical signal and acquires
the information transmitted by the acquisition module. The
resultant data will be displayed in the personal computer.
This resultant data will be compared with the previous data
to know the condition of the transformer.
This monitoring system continuously monitors the
conditions of the transformer for 24 hours. The
microcontroller in the system has the mechanism to send an
alarm or turn OFF the switching devices before overheating
occurs. This monitoring system is highly useful in areas
where the transformer is far away from the server or from the
substation.
This system is cost effective and easy to implement in
remote areas. This monitoring system uses only one
microcontroller as a main controller to monitor the
parameters which helps to know the conditions of the
transformer. This system uses a very little power
consumption and has a long battery life.
5. SIMULATION RESULT
This is the simulation result of the remote monitoring
system. The software used for the simulation is Proteus on a
MPLAB IDE compiler. The parameter of the temperature,
current and voltage by the PIC 16F877A microcontroller are
monitored from the temperature sensor, current transducer
and from the voltage transformer (variable resistors are used
instead) and displayed using the 16×2 alphanumeric LCD
display. The LED-BIBY will glow according to the
temperature condition
PIC
16F877A
CORE (TOP)
CORE (BOTTOM)
TS
TS
PHASE A PHASE CPHASE B
Fig-3: Temperature Monitoring

_______________________________________________________________________________________
Three-Phase 10-kVA
Switchable Transformer
PERSONAL COMPUTER
(SERVER MODULE)
POWER SUPPLY AND
LOAD
AND LOADA-PHASE
B-PHASE
C-PHASE
T
E
M
P
E
R
A
T
U
R
E
S
E
N
S
O
R
PIC 16F877A
16F877A
Zigbee Module
Fig-4: Block Diagram of Remote Monitoring System for a Three-Phase 10-kVA Switchable Transformer
Fig-5: Simulation Result
Zigbee
Module
ACQUISITION MODULE

_______________________________________________________________________________________
Fig-6: Monitored Parameters
6. CONCLUSION
The remote monitoring system that has been developed
was useful in understanding the conditions of the
transformer. It also enables the operator to monitor the
parameters far away from the transformer without the
displacement of the crew. This system uses very little power
consumption and has a long battery life. This system is cost
effective and is easy to operate, to maintain, and to reproduce
massively with low cost for applications in the field.
7. REFERENCES
[1] H.A.Dharmawan and S. A. M. Ali, “A Compact
Remote Monitoring System for a Three-Phase
10-kVA Energy -Efficient Switchable Distribution
Transformer,” IEEE Transactions on instrument
and measurement VOL. 61, NO. 3, march 2012
[2] H. A. Dharmawan and S. A. M. Ali, “A modular
approach and controller area network bus
implementation in an embedded system of a 3-
phase 10 kVA energy efficient switchable
distribution transformer,” in Proc. 5th
IEEE Conf.
Ind. Electron. Appl., Taichung, Taiwan, June 15–
17, 2010,pp. 62–67.
[3] Mei-sung,Yu-Lung Ke and He-Yau Kang,” Zigbee
Wireless Network for Transformer Load
Monitoring and Temperatute Sensitivity Analysis”
IEEE Industrial Applications Social Annual
meeting (IAS), 2011
[4] Abniki, H. Afsharirad, A. Mohseni, F. Khoshkhati,
H. Monsef, and P. Sahmsi, “Effective on-line
parameters for transformer monitoring and
protection,” in Proc. NAPS, 2010, pp. 1–5.
[5] H. A. Dharmawan and S. A. M. Ali, “Development
of switchable transformer research at University
of South Australia,” in Proc. Int. Conf. Renew.
Energies Power Qual., Valencia, Spain, Apr. 15–
17, 2009,pp. 1–6.
[6] H. A. Dharmawan and S. A. M. Ali, “Managing
distributed temperature measurements in an
embedded system of a 3-phase 10 kVA energy
efficient switchable distribution transformer
employing a modular approach,”in Proc. 2nd Int.
Conf. ACT, 2010, pp. 15–20.
[7] F. Poza, P. Marino, S. Otero, and F. Machado,
“Programmable electronic instrument for condition
monitoring of in-service power transformers,”IEEE
Trans. Instrum. Meas., vol. 55, no. 2, pp. 625–634,
Apr. 2006.
[8] Dharmawan, H. A. & Ali, S. A. M., "Design of
Switchable Transformer Control System
Employing the Micro-controller80C552",
International Journal of Applied Electromagnetics
and Mechanics, Japan, Vol. 13, pp.99-106, ISBN 1
58603 3271, 2002.
[9] Microchip Technology Inc.:PIC16F87X Data
Sheet. Microchip Technology Inc.2003
[10]”Electrical Machinery” book by Dr. P.S.Bimbhra,
7th
edition: 2009, khanna publishers.pg no. 1-159.
BIOGRAPHIES
S.Dinesh Kumar received B.E (ECE) from
Sri Ramakrishna Engineering College,
Coimbatore and currently doing M.E
Embedded Systems at Kumaraguru
College of Technology, Coimbatore.
Mr.R.Suresh Kumar received B.E (EEE)
from Government College of Technology,
Coimbatore and M.E Applied Electronics
from PSG College of Technology,
Coimbatore. He is presently working at
Kumaraguru College of Technology as
assistant Professor. His research and
teaching interests include Applied
electronics and Embedded systems. He is a
member of Indian Society for Technical
Education (ISTE).
Dr.Rani Thottungal obtained her B.E and
M.E degrees from Andhra University and
Doctorate from Bharathiar University. She
is currently working as Professor and
Head in EEE Department at Kumaraguru
College of Technology, Coimbatore. Her
research interest includes Power System,
Power Inverter and Power Quality Issues.

A remote monitoring system for a three phase 10-kva switchable distribution transformer using zigbee wireless network

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to A remote monitoring system for a three phase 10-kva switchable distribution transformer using zigbee wireless network (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

A remote monitoring system for a three phase 10-kva switchable distribution transformer using zigbee wireless network