![Intelligent wireless street lighting system
Fabio Leccese
Electronic Engineering Department
University Roma Tre
Rome, Italy
leccese@uniroma3.it
Zbigniew Leonowicz
Faculty of Electrical Engineering
Wroclaw University of Technology
Wroclaw, Poland
leonowicz@ieee.org
Abstract—We propose an innovative wireless street lighting
system with optimized management and efficiency. Wireless
communication uses ZigBee-based wireless devices which allow
more efficient street lamp system management, thanks to an
advanced interface and control architecture. It uses many sensors
to control and guarantee the optimal system parameters; the
information is transferred point-by-point using ZigBee
transmitters and receivers and is sent to a control terminal used
to check the state of the street lamps and to take appropriate
measures in case of failure. The system allows substantial energy
savings with increased performance and maintainability.
Keywords- automatio;, control system; lighting system; wireless
networks; ZigBee; sensors
I. INTRODUCTION
Lighting systems, particularly within the public sector, are
still designed per the previous standards of reliability and that
they don't usually profit of latest technological developments.
Recently, however, the increasing pressure associated with the
raw material prices and also the increasing social sensitivity to
CO2 emissions are leading to develop new techniques and
technologies which permit significant cost savings and larger
respect for the environment. In the literature we will notice
three solutions to those issues.
The first one, and maybe the most intuitive, is the use of
recent technologies for the sources of light. The LED
technology is thought as best solution but it offers several
edges. Researchers [1-4] have already thought of this risk,
coming up with advanced street lighting system based mostly
on LEDs.
The second resolution, and perhaps the most revolutionary,
is to use of remote management system based mostly on
intelligent lampposts that send info to a central management
system, simplifying the management and maintenance.
Researchers [5-6] have developed street lamp system using the
GPRS transmission, power line carrier transmission or GSM.
Finally, the third solution is to use of renewable energy
sources instead of typical power sources, therefore taking care
of the environment. In this field, solar energy is the most often
used resource.
Our work aims at unification of the three prospects, making
an intelligent lamppost managed by a remote controlled system
that uses LED-based lightweight supply and is powered by
renewable energy (solar panel and battery). The management is
implemented through a network of sensors to gather the
relevant info associated with the management and maintenance
of the system, transferring the data in wireless mode using the
ZigBee protocol (which has been chosen among numerous
alternatives because it is the most convenient, see clarification
below). The ZigBee remote sensing and management systems
are widely described in the literature; we can cite here as
examples the applications for the lighting systems [7-12].
II. GENERAL CONCEPT OF THE SYTEM
The system consists of a group of measuring stations in the
street (one station located in each lamppost) and a base station
located nearby. The system is designed as a modular system,
easily extendable. The measuring stations are used to observe
street conditions as the intensity of daylight and, depending on
the conditions they activate or off the lamps. Other factors
influencing the activation are: climatic conditions, seasons,
geographical location, and many possible alternative factors.
For these reasons every lamp is designed independent to
decide about the activation of light. The base station
conjointly checks if any lamp is correctly operating and sends
the message using the wireless network to the operator who
will act in case of malfunction.
A. Measuring Stations
The measuring station located in every lamppost consists of
many modules: the presence sensor, the sunshine sensor, the
failure sensor and an emergency switch.
Figure 1. Scheme of the lamppost with sensors.
Co-sponsored by the National Science Centre (Narodowe Centrum
Nauki) , Poland](https://image.slidesharecdn.com/ieeeprotechnosolutions-ieeeembeddedprojectintelligentwirelessstreetlightingsystem-160128120958/85/Ieeepro-techno-solutions-ieee-embedded-project-intelligent-wireless-street-lighting-system-1-320.jpg)
![TABLE I. ZIGBEE VS SELECTED OTHER WIRELESS TECHNOLOGIES
ZIGBEE WI-FI BLUETOOTH
IEEE
standard
802.15.04 802.11bgn 802.15.01
Main
application
Control Broadband Mobile devices
Number of
network
devices
Up to 65000 32 7
Bit rate 20 - 250 kb/s 11/54/300 Mb/s 720 kb/s
Range 100 m 100 m 10 m
Battery life 100 - 1000 days 1 - 5 days 1 - 7 days
On 2.4 GHz band the typical bit rate is of 250 kb/s, 40 kb/s
at 915 MHz and 20 kb/s at 868 MHz. The standard distance of
a ZigBee transmission vary, depending on the atmospheric
conditions and therefore the transmission power, ranges from
tens to hundred meters since the transmission power is
deliberately kept as low as necessary (in the order of few mW)
to keep up very low energy consumption [7].
In proposed system, the network is made to transfer data
from the lampposts to the central station. Data is transferred
purpose by purpose, from one lamppost to another one where
every lamppost has a distinctive address within the system. The
chosen transmission distance between the lampposts assures
that in case of failure of one lamp within the chain, the signal
will reach other operational lamppost while not breaking the
chain.
ZigBee wireless communication network has been
implemented with the utilization of radio frequency modules.
They operate within the ISM band at the frequency of 2.4 GHz.
The receiver sensitivity is high and therefore the chance of
receiving bad packets is low (about 1%). The modules ought to
be provided by 3V DC supply, and then the power
consumption is within the order of 50 mA. The module
supports sleep mode where consumption is smaller than 10µA.
III. REALIZATION OF THE SYSTEM
The operational test system operating in real conditions is
shown in Fig. 3. The proposed system can be used for upgrade
of existing typical lampposts, as well.
Power is provided by a battery, recharged from a solar
panel throughout the daytime. The capacity of the battery
depends on explicit parameters of the application. In the
designing part of a photovoltaic system the irradiation curves
of the positioning has been studied to work out the inclination
and orientation of the surface of solar panels that permit the
optimal operation. For the sizing of the panel it's necessary to
calculate the annual energy needed to power the lighting. The
charge controller manages the processes of the battery charge
and power provide. Current generated by photovoltaic panels is
handled by the controller to produce an output current for
battery charge. The charging method should be conducted
consistent with the battery knowledge (capacity, voltage,
chemistry, etc.)
Figure 3. View of the test system.
IV. SYSTEM TESTING AND DISCUSSION
The prototype has been tested in variable real-life
conditions to verify the general functionality and determine
points for improvement and optimization. The measurements
collected throughout the testing permit to calculate energy
savings and economic benefits.
It was found the applied ZigBee modules are appropriate
for this application. Every lamppost being placed at the
distance of 25 meters from one another, since modules have a
range of 100 m outdoors.
The functionality field tests were realized. First test
demonstrated that the system is in a position to transfer data
from any chosen lamppost to the management center when
passing the info through the remaining lampposts. During these
cases we obtained a transmission rate 99.98% to 100%
depending on the placement of sending unit.
The test verified what happens in case of a break-down of
one intermediate lamppost. The system seems indifferent to
such a malfunction, permitting the transmission with an
equivalent rate as within the previously described case. The
system becomes non-operating solely when 3 consecutive
lampposts transmission devices are non-operational.
A. Power management and consumption
The system was designed to operate stand-alone, supplied
by the energy from a solar panel. The benefits from this type of
power are important thus avoiding the tedious and expensive
wiring and connection to external power network, enabling
considerable savings and ease of implementation. The system
is intended to be low-power, minimizing the battery capacity
and also the energy acquired from the solar panel. These goals
were achieved through the utilization of the ZigBee module for
transmitting and receiving data, using LED lamps as](https://image.slidesharecdn.com/ieeeprotechnosolutions-ieeeembeddedprojectintelligentwirelessstreetlightingsystem-160128120958/85/Ieeepro-techno-solutions-ieee-embedded-project-intelligent-wireless-street-lighting-system-3-320.jpg)
![replacement of normal lamps and using special power-saving
solutions for microcontrollers and radio modules.
The program that controls the system is designed primarily
to avoid wasting energy. Firstly, as a result that the system
works solely in the darkness, avoiding waste of energy
throughout sunlight hours when the sole active device is the
solar panel that recharges battery. Secondly, the sensors enable
the system to operate solely when necessary. Thirdly, the
system employs highly economical LEDs to ensure correct
illumination and assure energy savings. Finally, when the
system is disabled, all devices (wireless module and
microcontrollers) are in the sleep mode, that permits negligible
power consumption. The wake-up is triggered by the change of
conditions (emergency device, presence sensor, etc.). The
selection of the battery depends on the conditions where the
system is installed.
B. Estimation of prices and savings
This proposed system may be criticized as being expensive
however we must consider its advantages: slightly higher
prices of the lampposts are compensated by lack of costly
wiring and the availability of power network and considerably
lower prices of maintenance (due to central management and
reliability of LEDs).
Energy savings are of utmost importance today. The goal
is, therefore, the reduction of operating prices of street lighting
with the creation of a system characterized by straightforward
installation and low power consumption, powered by a
renewable supply of energy through solar panels with no
harmful atmosphere emissions and minimizing light pollution.
Making a short comparison with the normal street lighting
systems: Supposing that one lamp is switched on for 4,000
hours per year. One streetlight has a median consumption of
200 W and the price of energy is of 200€ yearly. If suppose a
5 km long street, it is necessary to install 125 street lights (one
each forty meters), with yearly energy consumption of
25.000€. With the system presented in this paper, every lamp
uses about 20-25 W (95% of energy consumed by the LEDs).
With an equivalent example as before, energy cost decrease to
5.000€ (savings of 80%).
Based on the field tests another possibility of energy
savings becomes evident. Classical system consumes energy
independently if it is needed or not. It is active for about 10
hours daily and the total number of working hours is about 300
per month, versus 87-108 hours proposed system, savings of
about 66% to 71% are expected. The savings may be improved
by using more efficient LEDs, since the consumed energy
almost entirely depends on LEDs consumption.
Finally, since the system is powered by solar panels (with
batteries), the energy price does not depend on provider costs.
Consequently, the sole price to consider is that of the
installation and implementation of the system; with following
savings thanks to lower maintenance and energy savings.
V. CONCLUSIONS
In this paper a proposal of an intelligent street lighting
system is described that integrates new technologies, offering
ease of maintenance and energy savings. This is obtained by
using the highly economical LED technology supplied by
renewable energy provided by the solar panels and by using the
intelligent management of the lampposts.
The proposed system is especially appropriate for street
lighting in remote urban and rural areas where the traffic is low
at times. Independence of the power network permits to
implement it in remote areas where the classical systems are
prohibitively expensive. The system is versatile, extendable
and totally adjustable to user needs.
REFERENCES
[1] Costa, M.A.D.; Costa, G.H.; dos Santos, A.S.; Schuch, L.; Pinheiro,
J.R.; , "A high efficiency autonomous street lighting system based on
solar energy and LEDs," Power Electronics Conference, 2009. COBEP
'09. Brazilian , vol., no., pp.265-273, Sept. 27 2009-Oct. 1 2009
[2] Po-Yen Chen; Yi-Hua Liu; Yeu-Torng Yau; Hung-Chun Lee; ,
"Development of an energy efficient street light driving system,"
Sustainable Energy Technologies, 2008. ICSET 2008. IEEE
International Conference on , vol., no., pp.761-764, 24-27 Nov. 2008
[3] Wang Yongqing; Hao Chuncheng; Zhang Suoliang; Huang Yali; Wang
Hong; , "Design of Solar LED Street Lamp Automatic Control Circuit,"
Energy and Environment Technology, 2009. ICEET '09. International
Conference on , vol.1, no., pp.90-93, 16-18 Oct. 2009
[4] Wu Yue; Shi Changhong; Zhang Xianghong; Yang Wei; , "Design of
new intelligent street light control system," Control and Automation
(ICCA), 2010 8th IEEE International Conference on , vol., no., pp.1423-
1427, 9-11 June 2010
[5] Caponetto, R.; Dongola, G.; Fortuna, L.; Riscica, N.; Zufacchi, D.; ,
"Power consumption reduction in a remote controlled street lighting
system," Power Electronics, Electrical Drives, Automation and Motion,
2008. SPEEDAM 2008. International Symposium on , vol., no., pp.428-
433, 11-13 June 2008
[6] Yu Chen; Zhaoyu Liu; , "Distributed Intelligent City Street Lamp
Monitoring and Control System Based on Wireless Communication chip
nRF401," Networks Security, Wireless Communications and Trusted
Computing, 2009. NSWCTC '09. International Conference on , vol.2,
no., pp.278-281, 25-26 April 2009
[7] Lin Jianyi; Jin Xiulong; Mao Qianjie; , "Wireless Monitoring System of
Street Lamps Based on ZigBee," Wireless Communications, Networking
and Mobile Computing, 2009. WiCom '09. 5th International Conference
on , vol., no., pp.1-3, 24-26 Sept. 2009
[8] Dingfang Liu; Suiping Qi; Tundong Liu; Shou-zhi Yu; Funchun Sun; ,
"The design and realization of communication technology for street
lamps control system," Computer Science & Education, 2009. ICCSE
'09. 4th International Conference on , vol., no., pp.259-262, 25-28 July
2009
[9] Jun Liu; Cangxu Feng; Xuesong Suo; Aijun Yun; , "Street Lamp Control
System Based on Power Carrier Wave," Intelligent Information
Technology Application Workshops, 2008. IITAW '08. International
Symposium on , vol., no., pp.184-188, 21-22 Dec. 2008
doi: 10.1109/IITA.Workshops.2008.163
[10] Huanqi Tao; Heng Zhang; , "Forest Monitoring Application Systems
Based on Wireless Sensor Networks," Intelligent Information
Technology Application Workshops, 2009. IITAW '09. Third
International Symposium on , vol., no., pp.227-230, 21-22 Nov. 2009
[11] Liu Yanfei; Wang Cheng; Yu Chengbo; Qiao Xiaojun; , "Research on
ZigBee Wireless Sensors Network Based on ModBus Protocol,"
Information Technology and Applications, 2009. IFITA '09.
International Forum on , vol.1, no., pp.487-490, 15-17 May 2009
doi: 10.1109/IFITA.2009.30
[12] Valente, A.; Morais, R.; Serodio, C.; Mestre, P.; Pinto, S.; Cabral, M.; ,
"A ZigBee Sensor Element for Distributed Monitoring of Soil
Parameters in Environmental Monitoring," Sensors, 2007 IEEE , vol.,
no., pp.135-138, 28-31 Oct. 2007.](https://image.slidesharecdn.com/ieeeprotechnosolutions-ieeeembeddedprojectintelligentwirelessstreetlightingsystem-160128120958/85/Ieeepro-techno-solutions-ieee-embedded-project-intelligent-wireless-street-lighting-system-4-320.jpg)
Ieeepro techno solutions ieee embedded project intelligent wireless street lighting system
- 1. Intelligent wireless street lighting system Fabio Leccese Electronic Engineering Department University Roma Tre Rome, Italy leccese@uniroma3.it Zbigniew Leonowicz Faculty of Electrical Engineering Wroclaw University of Technology Wroclaw, Poland leonowicz@ieee.org Abstract—We propose an innovative wireless street lighting system with optimized management and efficiency. Wireless communication uses ZigBee-based wireless devices which allow more efficient street lamp system management, thanks to an advanced interface and control architecture. It uses many sensors to control and guarantee the optimal system parameters; the information is transferred point-by-point using ZigBee transmitters and receivers and is sent to a control terminal used to check the state of the street lamps and to take appropriate measures in case of failure. The system allows substantial energy savings with increased performance and maintainability. Keywords- automatio;, control system; lighting system; wireless networks; ZigBee; sensors I. INTRODUCTION Lighting systems, particularly within the public sector, are still designed per the previous standards of reliability and that they don't usually profit of latest technological developments. Recently, however, the increasing pressure associated with the raw material prices and also the increasing social sensitivity to CO2 emissions are leading to develop new techniques and technologies which permit significant cost savings and larger respect for the environment. In the literature we will notice three solutions to those issues. The first one, and maybe the most intuitive, is the use of recent technologies for the sources of light. The LED technology is thought as best solution but it offers several edges. Researchers [1-4] have already thought of this risk, coming up with advanced street lighting system based mostly on LEDs. The second resolution, and perhaps the most revolutionary, is to use of remote management system based mostly on intelligent lampposts that send info to a central management system, simplifying the management and maintenance. Researchers [5-6] have developed street lamp system using the GPRS transmission, power line carrier transmission or GSM. Finally, the third solution is to use of renewable energy sources instead of typical power sources, therefore taking care of the environment. In this field, solar energy is the most often used resource. Our work aims at unification of the three prospects, making an intelligent lamppost managed by a remote controlled system that uses LED-based lightweight supply and is powered by renewable energy (solar panel and battery). The management is implemented through a network of sensors to gather the relevant info associated with the management and maintenance of the system, transferring the data in wireless mode using the ZigBee protocol (which has been chosen among numerous alternatives because it is the most convenient, see clarification below). The ZigBee remote sensing and management systems are widely described in the literature; we can cite here as examples the applications for the lighting systems [7-12]. II. GENERAL CONCEPT OF THE SYTEM The system consists of a group of measuring stations in the street (one station located in each lamppost) and a base station located nearby. The system is designed as a modular system, easily extendable. The measuring stations are used to observe street conditions as the intensity of daylight and, depending on the conditions they activate or off the lamps. Other factors influencing the activation are: climatic conditions, seasons, geographical location, and many possible alternative factors. For these reasons every lamp is designed independent to decide about the activation of light. The base station conjointly checks if any lamp is correctly operating and sends the message using the wireless network to the operator who will act in case of malfunction. A. Measuring Stations The measuring station located in every lamppost consists of many modules: the presence sensor, the sunshine sensor, the failure sensor and an emergency switch. Figure 1. Scheme of the lamppost with sensors. Co-sponsored by the National Science Centre (Narodowe Centrum Nauki) , Poland
- 2. These devices work along and transfer the information to a microcontroller that processes the information and chooses the action. Every of those sensors has an assigned priority of transmission, for instance, the emergency switch takes precedence over the others. B. Presence detector The presence sensor has the task of identifying the passage of a vehicle or pedestrian causing the switching on of lamps. This feature permits to activate the lamps solely when necessary, avoiding waste of energy. The sensor ought to be placed at the optimal height, neither too low (e.g. to avoid any erroneous detection of small animals) nor too high (to avoid failure to detect e.g. children). C. Light sensor Light sensor will measure the external light intensity to assure a minimum level of illumination of the road, as needed by regulations. The sensor should have high sensitivity within the visible spectrum, providing a photocurrent high enough for low-light luminance levels. The microcontroller drives the lamp so as to keep up the constant level of illumination. Clearly, this action isn't needed throughout daylight time, however is desired within the early morning and at dusk, when it is not necessary to operate the lamp at full power however merely to "support" the daylight. This mode permits to save electrical power. D. Supervision module This sensor improves fault management and system maintenance. A Hall sensor detects when the lamp is switched on. The system recognizes false positives, as detected parameters are compared with the stored information. This information is reported by the ZigBee network to the station management unit, within which the operator is informed regarding the placement of the broken-down lamp and may send a technician to exchange the lamp. Additional security can provide the temperature sensor to ascertain the optimal operation of the lamp and constantly monitor the temperature of the LEDs (which influences the lifespan of the LED lamps). The chosen sensor allows precise AC or DC current sensing, additionally permitting the on-line power consumption measurement. E. Control unit The sensors transfer the collected information to a controller that runs the software to manage the system. The operation is processed as follows: After initial setting, the system is controlled by the light sensor that activates the microcontroller on condition that the daylight illumination is below a set threshold. During this case, the system reads the state of the emergency button, and activates the lamp. The same happens if the presence sensor detects a vehicle or a pedestrian. Once the lamp has been switched on, the operating sensor starts the monitoring and, in case of fault detection, sends information to the management center. If no fault is detected, the microcontroller measures the current by the Hall sensor storing the values in memory. All the operation is regulated by a timing management that permits the system is set for the predetermined time. At the stop signal, the lamp is turned off and therefore the cycle restarts. F. Management center The management center is that the hub of the system, since it permits the visualization and control of the complete lighting system. The transmission system consists of ZigBee devices that receives data of the state of the lamps and sends it to a terminal. The processing unit consists of a terminal with a serial UART interface that receives data regarding the state of the lamps provided by a ZigBee device, connected to the UART interface. The terminal is needed for graphical presentation of results. Additionally, knowledge on lamps operation are received along with the lamp address, consequently all faults can be easily identified. The graphical interface permits to visualize the state of the system (Fig. 2) with the state of the lights and the power consumption of every lamp (Power Consumption Data button). Figure 2. Exemplary GUI of the lighting system. The management can be extended so that other electrical systems, not solely lampposts are connected, and might send data regarding power consumptions to a central system for adjusting energy consumption to energy prices and for remote switching and management. G. Wireless ZigBee Network ZigBee is wireless communication technology primarily based on IEEE 802.15.4 norm for communication among multiple devices in a WPAN (Wireless Personal space Network). ZigBee is intended to be less complicated than other WPANs (such as Bluetooth) in terms of price and consumption of energy. The ZigBee Personal space Network consists of a minimum of one Coordinator, one (or more) Devices and, if necessary, of one (or more) Router. The bit rate of transmission depends on the frequency band.
- 3. TABLE I. ZIGBEE VS SELECTED OTHER WIRELESS TECHNOLOGIES ZIGBEE WI-FI BLUETOOTH IEEE standard 802.15.04 802.11bgn 802.15.01 Main application Control Broadband Mobile devices Number of network devices Up to 65000 32 7 Bit rate 20 - 250 kb/s 11/54/300 Mb/s 720 kb/s Range 100 m 100 m 10 m Battery life 100 - 1000 days 1 - 5 days 1 - 7 days On 2.4 GHz band the typical bit rate is of 250 kb/s, 40 kb/s at 915 MHz and 20 kb/s at 868 MHz. The standard distance of a ZigBee transmission vary, depending on the atmospheric conditions and therefore the transmission power, ranges from tens to hundred meters since the transmission power is deliberately kept as low as necessary (in the order of few mW) to keep up very low energy consumption [7]. In proposed system, the network is made to transfer data from the lampposts to the central station. Data is transferred purpose by purpose, from one lamppost to another one where every lamppost has a distinctive address within the system. The chosen transmission distance between the lampposts assures that in case of failure of one lamp within the chain, the signal will reach other operational lamppost while not breaking the chain. ZigBee wireless communication network has been implemented with the utilization of radio frequency modules. They operate within the ISM band at the frequency of 2.4 GHz. The receiver sensitivity is high and therefore the chance of receiving bad packets is low (about 1%). The modules ought to be provided by 3V DC supply, and then the power consumption is within the order of 50 mA. The module supports sleep mode where consumption is smaller than 10µA. III. REALIZATION OF THE SYSTEM The operational test system operating in real conditions is shown in Fig. 3. The proposed system can be used for upgrade of existing typical lampposts, as well. Power is provided by a battery, recharged from a solar panel throughout the daytime. The capacity of the battery depends on explicit parameters of the application. In the designing part of a photovoltaic system the irradiation curves of the positioning has been studied to work out the inclination and orientation of the surface of solar panels that permit the optimal operation. For the sizing of the panel it's necessary to calculate the annual energy needed to power the lighting. The charge controller manages the processes of the battery charge and power provide. Current generated by photovoltaic panels is handled by the controller to produce an output current for battery charge. The charging method should be conducted consistent with the battery knowledge (capacity, voltage, chemistry, etc.) Figure 3. View of the test system. IV. SYSTEM TESTING AND DISCUSSION The prototype has been tested in variable real-life conditions to verify the general functionality and determine points for improvement and optimization. The measurements collected throughout the testing permit to calculate energy savings and economic benefits. It was found the applied ZigBee modules are appropriate for this application. Every lamppost being placed at the distance of 25 meters from one another, since modules have a range of 100 m outdoors. The functionality field tests were realized. First test demonstrated that the system is in a position to transfer data from any chosen lamppost to the management center when passing the info through the remaining lampposts. During these cases we obtained a transmission rate 99.98% to 100% depending on the placement of sending unit. The test verified what happens in case of a break-down of one intermediate lamppost. The system seems indifferent to such a malfunction, permitting the transmission with an equivalent rate as within the previously described case. The system becomes non-operating solely when 3 consecutive lampposts transmission devices are non-operational. A. Power management and consumption The system was designed to operate stand-alone, supplied by the energy from a solar panel. The benefits from this type of power are important thus avoiding the tedious and expensive wiring and connection to external power network, enabling considerable savings and ease of implementation. The system is intended to be low-power, minimizing the battery capacity and also the energy acquired from the solar panel. These goals were achieved through the utilization of the ZigBee module for transmitting and receiving data, using LED lamps as
- 4. replacement of normal lamps and using special power-saving solutions for microcontrollers and radio modules. The program that controls the system is designed primarily to avoid wasting energy. Firstly, as a result that the system works solely in the darkness, avoiding waste of energy throughout sunlight hours when the sole active device is the solar panel that recharges battery. Secondly, the sensors enable the system to operate solely when necessary. Thirdly, the system employs highly economical LEDs to ensure correct illumination and assure energy savings. Finally, when the system is disabled, all devices (wireless module and microcontrollers) are in the sleep mode, that permits negligible power consumption. The wake-up is triggered by the change of conditions (emergency device, presence sensor, etc.). The selection of the battery depends on the conditions where the system is installed. B. Estimation of prices and savings This proposed system may be criticized as being expensive however we must consider its advantages: slightly higher prices of the lampposts are compensated by lack of costly wiring and the availability of power network and considerably lower prices of maintenance (due to central management and reliability of LEDs). Energy savings are of utmost importance today. The goal is, therefore, the reduction of operating prices of street lighting with the creation of a system characterized by straightforward installation and low power consumption, powered by a renewable supply of energy through solar panels with no harmful atmosphere emissions and minimizing light pollution. Making a short comparison with the normal street lighting systems: Supposing that one lamp is switched on for 4,000 hours per year. One streetlight has a median consumption of 200 W and the price of energy is of 200€ yearly. If suppose a 5 km long street, it is necessary to install 125 street lights (one each forty meters), with yearly energy consumption of 25.000€. With the system presented in this paper, every lamp uses about 20-25 W (95% of energy consumed by the LEDs). With an equivalent example as before, energy cost decrease to 5.000€ (savings of 80%). Based on the field tests another possibility of energy savings becomes evident. Classical system consumes energy independently if it is needed or not. It is active for about 10 hours daily and the total number of working hours is about 300 per month, versus 87-108 hours proposed system, savings of about 66% to 71% are expected. The savings may be improved by using more efficient LEDs, since the consumed energy almost entirely depends on LEDs consumption. Finally, since the system is powered by solar panels (with batteries), the energy price does not depend on provider costs. Consequently, the sole price to consider is that of the installation and implementation of the system; with following savings thanks to lower maintenance and energy savings. V. CONCLUSIONS In this paper a proposal of an intelligent street lighting system is described that integrates new technologies, offering ease of maintenance and energy savings. This is obtained by using the highly economical LED technology supplied by renewable energy provided by the solar panels and by using the intelligent management of the lampposts. The proposed system is especially appropriate for street lighting in remote urban and rural areas where the traffic is low at times. Independence of the power network permits to implement it in remote areas where the classical systems are prohibitively expensive. The system is versatile, extendable and totally adjustable to user needs. REFERENCES [1] Costa, M.A.D.; Costa, G.H.; dos Santos, A.S.; Schuch, L.; Pinheiro, J.R.; , "A high efficiency autonomous street lighting system based on solar energy and LEDs," Power Electronics Conference, 2009. COBEP '09. Brazilian , vol., no., pp.265-273, Sept. 27 2009-Oct. 1 2009 [2] Po-Yen Chen; Yi-Hua Liu; Yeu-Torng Yau; Hung-Chun Lee; , "Development of an energy efficient street light driving system," Sustainable Energy Technologies, 2008. ICSET 2008. IEEE International Conference on , vol., no., pp.761-764, 24-27 Nov. 2008 [3] Wang Yongqing; Hao Chuncheng; Zhang Suoliang; Huang Yali; Wang Hong; , "Design of Solar LED Street Lamp Automatic Control Circuit," Energy and Environment Technology, 2009. ICEET '09. International Conference on , vol.1, no., pp.90-93, 16-18 Oct. 2009 [4] Wu Yue; Shi Changhong; Zhang Xianghong; Yang Wei; , "Design of new intelligent street light control system," Control and Automation (ICCA), 2010 8th IEEE International Conference on , vol., no., pp.1423- 1427, 9-11 June 2010 [5] Caponetto, R.; Dongola, G.; Fortuna, L.; Riscica, N.; Zufacchi, D.; , "Power consumption reduction in a remote controlled street lighting system," Power Electronics, Electrical Drives, Automation and Motion, 2008. SPEEDAM 2008. International Symposium on , vol., no., pp.428- 433, 11-13 June 2008 [6] Yu Chen; Zhaoyu Liu; , "Distributed Intelligent City Street Lamp Monitoring and Control System Based on Wireless Communication chip nRF401," Networks Security, Wireless Communications and Trusted Computing, 2009. NSWCTC '09. International Conference on , vol.2, no., pp.278-281, 25-26 April 2009 [7] Lin Jianyi; Jin Xiulong; Mao Qianjie; , "Wireless Monitoring System of Street Lamps Based on ZigBee," Wireless Communications, Networking and Mobile Computing, 2009. WiCom '09. 5th International Conference on , vol., no., pp.1-3, 24-26 Sept. 2009 [8] Dingfang Liu; Suiping Qi; Tundong Liu; Shou-zhi Yu; Funchun Sun; , "The design and realization of communication technology for street lamps control system," Computer Science & Education, 2009. ICCSE '09. 4th International Conference on , vol., no., pp.259-262, 25-28 July 2009 [9] Jun Liu; Cangxu Feng; Xuesong Suo; Aijun Yun; , "Street Lamp Control System Based on Power Carrier Wave," Intelligent Information Technology Application Workshops, 2008. IITAW '08. International Symposium on , vol., no., pp.184-188, 21-22 Dec. 2008 doi: 10.1109/IITA.Workshops.2008.163 [10] Huanqi Tao; Heng Zhang; , "Forest Monitoring Application Systems Based on Wireless Sensor Networks," Intelligent Information Technology Application Workshops, 2009. IITAW '09. Third International Symposium on , vol., no., pp.227-230, 21-22 Nov. 2009 [11] Liu Yanfei; Wang Cheng; Yu Chengbo; Qiao Xiaojun; , "Research on ZigBee Wireless Sensors Network Based on ModBus Protocol," Information Technology and Applications, 2009. IFITA '09. International Forum on , vol.1, no., pp.487-490, 15-17 May 2009 doi: 10.1109/IFITA.2009.30 [12] Valente, A.; Morais, R.; Serodio, C.; Mestre, P.; Pinto, S.; Cabral, M.; , "A ZigBee Sensor Element for Distributed Monitoring of Soil Parameters in Environmental Monitoring," Sensors, 2007 IEEE , vol., no., pp.135-138, 28-31 Oct. 2007.