Accubar multi interface gauge pressure sensor

Sutron Corporation | 22400 Davis Drive | Sterling, VA 20164 | 703.406.2800 | www.sutron.com | sales@sutron.com
Accubar Multi-Interface
Gauge Pressure Sensor
Models 5600-0125-7,-8 / 5600-0124-1 / 56-0125-50-1,-2
OPERATIONS & MAINTENANCE
MANUAL
Part No. 8800-1122
Rev. C
March 2005

i
Table of Contents
1. Introduction ...................................................................................................................... 1
Special Note Concerning the 5600-0124-1...............................................................................1
Special Note Concerning the 56-0125-50-1 and the 56-0125-50-2..........................................1
2. Quick Start ....................................................................................................................... 2
5600-0125 to 8200 ...................................................................................................................2
5600-0125 or 5600-0124 to 8210.............................................................................................2
3. Cabling ............................................................................................................................. 3
DB9 Connector (Not applicable to the 5600-0124)..................................................................3
Terminal Block.........................................................................................................................3
SDI-12 Wiring..........................................................................................................................4
RS-232 Wiring .........................................................................................................................4
Analog Wiring..........................................................................................................................5
Quadrature Output Wiring........................................................................................................5
4. Setup and Operation........................................................................................................ 6
Introduction..............................................................................................................................6
Nomenclature ...........................................................................................................................6
RS-232 Automatic Reading Mode............................................................................................6
Setting the Address...................................................................................................................7
Using Switches to Set the Address.............................................................................7
Using a command to Set the Address.........................................................................8
Verifying the Address and Operation.......................................................................................9
Commands (Overview).............................................................................................................9
Making a Measurement ............................................................................................................10
Selecting a measurement command class...................................................................10
Always supported.........................................................................................10
Multiple long measurement time sensors.....................................................10
Improved data integrity checking.................................................................11
Making a non-concurrent Measurement (M command) .............................................11
Making a Concurrent Measurement (C command) ....................................................12
Making a non-concurrent Measurement with CRC-16 (MC command).....................13
Making a Concurrent Measurement with CRC-16 (CC command)............................15
Other Measurements ..................................................................................................16
Changing the Units.....................................................................................................18
Setting User Units ......................................................................................................18
Field Calibration ........................................................................................................19
Configuring the Analog Output ................................................................................................20
Analog Output Range.................................................................................................20
Converting Voltage to Pressure..................................................................................21
Configuring the Quadrature Output..........................................................................................21
Setting the Quadrature Scale Factor, Threshold, and Step Rate.................................21
Setting the Quadrature Output’s Reading...................................................................22
Use of an ACCUBAR®
with a Sutron 5600-0126-1 Chart Drive...............................23
Configuring the Operating Mode and Averaging Time............................................................23
Setting the Operating Mode .......................................................................................23
Setting the Averaging Time........................................................................................24
Resetting the unit to Factory Default Configuration.................................................................24

ii
5. Command Reference....................................................................................................... 26
Accubar Basic SDI-12 Commands...........................................................................................26
Accubar Extended Commands .................................................................................................35
Additional commands for Analog output units.........................................................................38
Additional commands for Quadrature output units...................................................................39
6. Installation ........................................................................................................................ 41
7. Calibration ........................................................................................................................ 42
Factory Calibration...................................................................................................................42
Metrology Lab Calibration.......................................................................................................42
8. Troubleshooting and Maintenance................................................................................... 44
Troubleshooting .......................................................................................................................44
Additional Troubleshooting commands .....................................................................44
Measure Break detect time...........................................................................44
Test Analog output.......................................................................................45
Maintenance .............................................................................................................................45
9. Specifications for 5600-0125 Gauge ACCUBAR ............................................................. 46
10. Specifications for 5600-0124 Gauge ACCUBAR ............................................................. 47
11. Specifications for 56-0125-50 Gauge ACCUBAR............................................................ 48
Appendix A -- Introduction to Pressure Measurement ............................................................. 49
TYPES OF PRESSURE MEASUREMENTS..........................................................................49
PRESSURE UNITS .................................................................................................................50
ERROR DEFINITIONS AND EXAMPLES ...........................................................................51
Appendix B -- SDI-12 with the Sutron 8200, 8200A, and 8210................................................ 53
Entering Extended Commands for Configuration Purposes .....................................................53
From the Front Panel..................................................................................................53
From a PC connected to the RS-232 port...................................................................53
Logging data from the M1 or M2 commands or from addresses above 9 ................................53
Logging Temperature data from the Accubar ............................................................54
Logging data with multiple data recorders ...............................................................................54
Setup two 8200s with one ACCUBAR ......................................................................54
Setup two 8200s with two ACCUBARS....................................................................55
Appendix C -- Procomm setup for use with the Accubar ......................................................... 57
Appendix D -- Sutron Customer Service Policy........................................................................ 59

1
1. Introduction
The ACCUBAR®
Pressure Sensor is a solid-state pressure transducer suitable for data collection and
monitoring applications. The ACCUBAR®
sensor has been designed with the following features to operate
in a wide range of applications:
low power
consumption
standby power is 0.2mA on non-analog versions, average power when taking
measurements every 15 minutes via SDI-12 is less than 0.25 mA.
High accuracy 0.0044 psi for pressures less than 4.4 psi, 0.1% of reading for pressures 4.4
to 22 psi. (0.01 ft. up to 10 ft. of water, 0.1% of reading 10 to 50 feet of
water)
Excellent
stability
measurement error increases by no more than 0.02% of 22 psi or 0.1% of the
actual pressure, whichever is greater, for a period of 6 months.
full temperature
compensation
the accuracy is maintained over the temperature range of -40° to +60°C.
Selectable units the sensor can be configured to output the data in psi, feet of water,
kilopascals, centimeters of water, or customer defined units.
non-volatile
setup
the setup is stored in EEROM and remains even when power is removed
from the sensor
Wide operating
voltage
the sensor operates over the voltage range of 8 to 28 VDC
Special Note Concerning the 5600-0124-1
The 5600-0124-1 is a SDI-12 only version of the ACCUBAR®
. It does not support RS-232
communications, analog output, or quadrature output. It does not have internal overpressure protection.
These differences should be kept in mind when using this manual. There are several features described that
are applicable to the 5600-0125 family and the 56-0125 family, but are not applicable to the 5600-0124-1.
Special Note Concerning the 56-0125-50-1 and the 56-0125-50-2
The 56-0125 family of ACCUBAR®
products look and function the same as the 5600-0125 family. The
main difference is that the 56-0125 family of products is rated for higher pressures. The 56-0125-50 series
are 50 PSI units (115 feet of water or 35 meters of water) while the 5600-0125 family is limited to 22 PSI
(50 ft or 15 m). The 56-0125-50-1 supports quadrature output in addition to SDI-12 and RS-232 just like
the 5600-0125-7. The 56-0125-50-2 also supports analog output just like the 5600-0125-8. To cut down
on the proliferation of model numbers in the manual text, there are times that only the 5600-0125 family
model number is included.
Sutron Corporation Accubar Gauge Pressure Sensor Users Manual Rev. C #8800-1122 03/2005 1

2
2. Quick Start
The ACCUBAR®
sensor comes with a setup compatible with a Sutron 8200/8210. If you have an
8200 or 8210, you are able to operate the ACCUBAR®
without making any changes to the setup.
If you do not have an 8200 or 8210, you may need to change the wiring to make it connect to your
system as described in Chapter 3.
5600-0125 to 8200
To use the ACCUBAR®
with the 8200 follow these simple steps:
• Connect the sensor to your Sutron 8200 Data Logger SDI-12 port on the front panel of the
8200, using a DB9 Male - Male straight through cable.
• Connect a pressure source to the ACCUBAR. Make sure the pressure source will not exceed
35 psi and that the pressure medium is air or dry gas, i.e., Nitrogen.
• Use the 8200 SYSTEM SETUPENABLE SENSOR menu to turn SDI0-1 ON. If you want to
see the units indicator for the measurement also turn SDI0-2 ON. Refer to the Sutron 8200
Data Logger Operations and Maintenance Manual if you do not know how to ENABLE
sensors.
• Use the 8200 VIEWLIVE READINGS menu and select the SDI0-1 sensor.
The 8200 will now display the pressure readings from the ACCUBAR®
sensor in units of feet of
water.
5600-0125 or 5600-0124 to 8210
To use the ACCUBAR®
with the 8210 follow these simple steps:
• Connect the sensor PWR IN +, PWR IN -, and SDI DATA terminals to your Sutron 8210
Data Logger SDI-12 port (PWR IN+ to SDI-12 +, PWR IN- to SDI-12 G, and SDI DATA to
SDI-12 D).
• Connect a pressure source to the ACCUBAR. Make sure the pressure source will not exceed
35 psi and that the pressure medium is air or dry gas, i.e., Nitrogen.
• Use the 8210 SYSTEM SETUPENABLE SENSOR menu to turn SDI0-1 ON. If you want to
see the units indicator for the measurement also turn SDI0-2 ON. Refer to the Sutron
8210/8200A Data Logger Operations Manual if you do not know how to ENABLE sensors.
• Use the 8210 VIEWLIVE READINGS menu and select the SDI0-1 sensor.
The 8210 will now display the pressure readings from the ACCUBAR®
sensor in units of feet of
water.

3
3. Cabling
DB9 Connector (Not applicable to the 5600-0124)
The ACCUBAR®
comes with a DB9F connector on it. The wiring of the connector is as follows:
Name DB9F Pin Notes
Ground 5
RXD 3 Data to the Accubar
TXD 2 Data from the Accubar
Battery 9 (8 to 28VDC)
Ground 7
SDI Data 1 SDI-12 Data line
DTR 4 Must be asserted for RS-232 communication
N/C 6
N/C 8
Terminal Block
The following table contains pin descriptions for the terminal block.
Description Terminal
Block
Notes
Power IN Positive 1 +8 to +28 VDC
Power IN Ground 2
SDI-12 Data 3
Analog output 4 0-5 VDC (only on analog output models)
Analog ground 5 Also can be used as ground for Quad. out
Quadrature out Phase A 6 Phase A will lead Phase B for positive change
Quadrature out Phase B 7 Phase A leads by going to 5V before Phase B
N/C 8 Reserved
Note: Only the first three positions are applicable to the 5600-0124-1.

4
SDI-12 Wiring
The ACCUBAR®
conforms to version 1.2 or 1.3 of the SDI-12 standard depending on firmware
version. Firmware versions V2.0 and higher support version 1.3 of the standard. This means that
it also conforms with versions 1.0, 1.1, and 1.2. Only three wires are needed to use the
ACCUBAR®
SDI-12 interface. The following table contains pin descriptions for the terminal
block on the ACCUBAR®
.
Description Terminal Block Data Recorder Connection
Battery 1 Connect to Battery or data recorder
supplied voltage
Ground 2 Connect to Ground
SDI Data 3 Connect to data recorder SDI Data line
Instead of using the terminal block on 5600-0125-7, and -8 or 56-0125-50-1, and -2 models, an
SDI-12 connection can be made through the DB9F connector. The following table indicates the
required connections.
Description DB9F connector Data Recorder Connection
Battery 9 Connect to Battery or data recorder
supplied voltage
Ground 5 or 7 Connect to Ground
SDI Data 1 Connect to data recorder SDI Data line
NOTE: When connecting via the DB9F connector to the SDI-12 port of the SUTRON 8200, just
use a straight through DB9 male to DB9 male cable. The pin outs have been arranged to allow the
use of this commonly available standard cable.
RS-232 Wiring
The default communications parameters for RS-232 are:
• 1200 baud
• 7 data bits with even parity added as an eighth bit
• One stop bit
The following table contains pin descriptions for the DB9F connector on the Accubar, with the
corresponding RS-232 cable connections to PC.
Description DB-9F
connector
IBM AT Connection
(DB-9F cable)
IBM PC or any DTE
Connection (DB-25-F
cable)
Ground 5 5 7
Receive Data 3 3 2
Transmit Data 2 2 3
Battery 9 Supply Voltage Supply Voltage
Ground 7 Supply Ground Supply Ground
SDI Data 1
DTR 4 4 20

5
When Data Terminal Ready (DTR) is off, the ACCUBAR®
enters a low-power standby mode and
the RS-232 drivers are turned off. When DTR is raised, the unit resumes normal operation.
NOTE: The unit can be powered off of the DTR pin but a typical RS-232 connector will not
supply enough current to power the unit and an external supply will be required. Supply Voltage
and Supply Ground are where the supply voltage for the ACCUBAR®
is applied if it is going to be
powered via the DB-9F connector.
Even though the unit can be powered off of the DTR pin, the DTR and Battery pins (4 and 9) are
NOT interchangeable. The DTR line must be high for the ACCUBAR®
to acknowledge an RS-
232 connection.
Pins 5 and 7 are connected internally and are interchangeable. The two connections are provided
as a convenience to the RS-232 user.
NOTE: Pins 1 and 2 of the terminal block can be used to provide power to the unit. This allows
the ACCUBAR®
to connect via the DB9F connector directly to any RS-232 DTE port, i.e., the
serial port of most computers.
Analog Wiring
The following table contains pin descriptions for the terminal block on the analog version of the
ACCUBAR.
Description Terminal Block Connection
Battery 1 Connect to Battery + or data recorder supplied
voltage
Ground 2 Connect to Battery - or data recorder ground
Analog out + 4 Connect to Analog + input
Analog out - 5 Connect to Analog – input
NOTE: Analog out - is connected internally to ground. The analog out - pin is provided to allow
the unit to be connected to a differential input and eliminate errors due to the voltage drop in the
ground connection on long cable runs.
Quadrature Output Wiring
The quadrature output is available on the 5600-0125-7 and -8 models and on the 56-0125-50-1 and
-2 models. The following table contains pin descriptions for the terminal block.
Description Terminal Block Connection
Battery 1 Connect to Battery + or data recorder supplied
voltage or to chart drive supplied voltage
Ground 2 Connect to Battery - or data recorder ground or
chart drive ground
Quadrature
out Phase A
6 Phase A will lead Phase B for positive change
Quadrature
out Phase B
7 Phase A leads by going to 5V before Phase B
Note: The number of steps per unit of change, the step rate, and the step threshold are set via the
XQS command.

6
4. Setup and Operation
Introduction
This section will familiarize you with the steps and commands needed to alter the setup of the
ACCUBAR. If you will use the ACCUBAR®
sensor at address 0 (the factory default) and can
accept the output in units of feet of water, you will not need to use these commands. Typically,
you will need to issue some of the commands, so we recommend you learn how to do so. Learning
to issue commands also helps if you need to troubleshoot a sensor.
Users of the analog version of the ACCUBAR®
will not need to use these commands if the output
range of 0 to 22psi (0 to 50.76 feet of water) is acceptable. Users of the analog version will,
however, probably wish to customize the output range to suit their application. To customize the
output range, analog users will need to know how to issue commands.
To issue commands to the ACCUBAR®
via SDI-12, you will need to connect it to a data recorder,
such as a Sutron 8200, 8210, 8400, 9210, or Xpert which is capable of issuing standard and
extended SDI-12 commands. Follow the instructions in Sections 2 and 3 in order to make these
connections.
To issue commands to the ACCUBAR®
via RS-232, you will need to connect it to an RS-232
terminal or to a computer running terminal emulation (communications) software and to a power
supply or battery. Follow the instructions in Section 3 in order to make these connections
Nomenclature
All commands have three components: the device address, the command body, and the
command termination.
The device address is a single character and is the first character of a command. In the examples
that follow, it is usually the number 0 (the default address as shipped from the factory).
The command body and the responses are shown as a combination of upper and lower case
letters. The upper case letters are the fixed portions of the command and the lower case letters are
the variables or values. In the specific examples, you will see that the lower case letters are
replaced with actual numbers.
All commands are shown with an exclamation point (!) as the command terminator. This
command terminator works with both the SDI-12 and RS-232 interfaces. With RS-232, you have
the additional option of terminating the command with a carriage return <CR> and/or line feed
<LF> in place of the exclamation point.
RS-232 Automatic Reading Mode
The RS-232 port supports an automatic reading mode. By default, when an RS-232 connection is
made (DTR asserted), the unit will start making measurements and reporting the pressure reading
out the RS-232 port. The reported pressure will be same as provided by the measure command (M
command). This means that offsets, pressure units, and resolution can be set via all of the
appropriate commands. The output is the pressure followed by a carriage return line feed
sequence. For example:
0.0091
0.0090

7
The ACCUBAR®
continues to report the pressure at the reading rate. The reading rate can be
changed by using the XT command to change the averaging time. If the ACCUBAR®
receives a
command terminator, either an exclamation point “!” or a carriage return, then the automatic
reading mode will be disabled for that RS-232 session and the interaction with the unit will
become command driven, just like SDI-12. Beginning with version 2.1 of the firmware, it is
possible to make the command driven mode the default by using issuing the aXOP+1! command.
See the description of the XOP command in the command reference for further details. When in
command driven mode, any command can be aborted by sending a command terminator, a carriage
return. Then a new command can be issued.
Note: If both an RS-232 connection and a SDI-12 connection are made to one ACCUBAR®
, the
SDI-12 takes priority. This means that during the time of a SDI-12 command, the unit will not
accept commands from the RS-232 port. Once the unit has finish with the SDI-12 command, it
will revert back to accepting RS-232 commands.
Setting the Address
If you are using the ACCUBAR®
connected with other SDI-12 devices, you will need to change
the ACCUBAR®
address. Otherwise, skip this section. The address simply lets multiple devices
share the same wiring. When the data recorder needs data from a particular sensor, it requests data
using an address. Only the device with the matching address will reply. For convenience in setting
up the unit when only one sensor is connected, the ACCUBAR®
supports wildcard addresses of
asterisk (*) and question mark (?).
The default SDI-12 address is 0. There are two ways to set the address: switches and via
commands.
Using Switches to Set the Address
NOTE: It is usually easier to set the address via a software command, as described in the next
section.
Remove the cover for the sensor and set the switches to one of the settings as follows:
Address Switch 4 Switch 3 Switch 2 Switch 1
0 off Off off off
1 off Off off ON
2 off Off ON off
3 off Off ON ON
4 off ON off off
5 off ON off ON
6 off ON ON off
7 off ON ON ON
8 ON Off off off
9 ON Off off ON
A ON Off ON off
B ON Off ON ON
C ON ON off off
D ON ON off ON
E ON ON ON off
F ON ON ON ON

8
Note: All other switches in the ACCUBAR®
need to be OFF. The factory default for all switches
is OFF (address 0). The ACCUBAR®
will not operate properly if any of the switches (5 to 8) are
set ON.
Using a command to Set the Address
In order to set the address by SDI-12 command or RS-232 command, the DIP switch address must
be set to 0 (Switches 1,2,3,4 OFF). This is the factory setting for the switches. Also, no other
SDI-12 devices connected to the system should be set to address 0 or to the desired ACCUBAR®
address. Hint: If you do not know the address of a particular ACCUBAR, use the unknown
address command to have the ACCUBAR®
identify itself.
NOTE: There can only be one ACCUBAR®
connected in order for the unknown address
command to work. The syntax for the unknown address command is
*X?!
The ACCUBAR®
also supports an alternate version of the unknown address command which is a
command acknowledge to a wildcard address. The syntax for this version is:
*!
Beginning with version 1.2 of the SDI-12 specification there is an address query command
defined. Therefore another version of the request unknown address or address query command is:
?!
The SDI-12 command for setting the ACCUBAR's address is the XAD command
0XADnAn! where 0 is the current address of the device, n is the new SDI-12 address
and n is the same address repeated (0 to 9, A to Z, a to z).
Note that the command follows the SDI-12 standard beginning with the address and ending with
"!".
The ACCUBAR®
will issue a reply message in response to the command if the command was
recognized. The message will be 00011 which is explained in the Command Reference. If you do
not get this message, try the command again and check the switches (Unit must be set to address 0
since that is the address this command trying to change from). Note: The ACCUBAR®
will not
respond if the command is invalid, i.e., there is a typing mistake in the command or the two copies
of the new address do not match.
As an example, the following command would set the ACCUBAR®
address to 5:
0XAD5A5!
Subsequently, the address can be set to a different address, 9 for example, by the command:
5XAD9A9!

9
The ACCUBAR®
also supports an alternate version of the set Address command as specified in
SDI-12 standard version 1.2.
0An! where 0 is the current address of the device, n is the new SDI-12 address
(0 to 9, A to Z, a to z).
As an example, the following command would set the ACCUBAR®
address to 5:
0A5!
The ACCUBAR®
will respond with the new address which is 5.
Subsequently, the address can be set to a different address, 9 for example, by the command:
5A9!
Verifying the Address and Operation
The ACCUBAR®
will respond with an identifying message when it receives the send identification
command, I. The format of the command is:
aI! Where a is the address for the ACCUBAR.
The ACCUBAR®
will reply with
a13 SUTRON 0125-71.0sssssssVvvv
a
13
SUTRON
0125-7
1.0
sssssss
Vvvv
Where:
SDI-12 address
supports SDI version 1.3 commands
manufacturer SUTRON
Sutron model number
hardware revision level
sensor serial number
the software revision
If you do not get a reply, check the address setting for the ACCUBAR®
and make sure you use the
proper address for the sensor.
Commands (Overview)
The commands to set up and operate the ACCUBAR®
are those defined by the SDI-12
specifications plus some extended commands defined by Sutron. Note: ALL ACCUBAR®
COMMANDS ARE UPPER CASE. All commands start with a single-character address and end
in an exclamation point. The address is a single character with values 0 to 9, A to Z, and a to z.
Values are entered in the form of a polarity sign (+ or −) followed by up to seven digits, including
a decimal point. The commands are in ASCII and all the replies use printable ASCII characters
followed by <CR> <LF>. The case of the letters is important. An “A” is not the same as an “a”.
The ACCUBAR®
replies to all SDI-12 commands it supports. If the ACCUBAR®
receives a
command it does not support, no reply is made. The reply will have one of two forms:

10
a0000 Where a is the address and the 0000 indicates that there is no
further message to send
or
atttn
and
a
Where a is the address, ttt is the amount of time, in seconds,
the ACCUBAR®
needs to make the measurement or process
the command and n is the number of values that can be
collected. In this form the sensor will also respond with its
address when the data is ready to collect if ttt is not 000. This
response is called a service request.
If you issued the change address command or the identify command described in the previous
sections, you already have some experience with using ACCUBAR®
commands. There are other
commands available to make measurements, set the type of output units for the measurements,
perform special scaling of the measurements, do field calibration, etc. The following sections
describe the commands by function.
Making a Measurement
There are four classes of measurement commands which will be referred to as M commands
(Measurement Commands), C commands (Concurrent Measurement Commands), MC commands
(Measurement commands with CRC-16), and CC commands (Concurrent Measurement
Commands with CRC-16). Concurrent measurement commands are new to version 1.2 of the SDI-
12 specification. The commands with CRC-16 are new to version 1.3 of the SDI-12 specification.
In the original class of “M” measurement commands, the data recorder issued the measurement
command and then waited for the sensor to complete the measurement before continuing the data
collection cycle. Only one sensor could be accessed at a time and a maximum of nine parameters
could be returned. With version 1.2 of the specification, concurrent measurements were defined.
With a concurrent measurement, the data recorder can request the sensor to take a measurement,
determine how long it will be until the sensor has a reading, and then continue on making requests
to other sensors on the SDI-12 bus. This way multiple sensors are taking measurements concurrent
with each other. Once the measurement time for a sensor has expired the data recorder polls the
sensor for the data. The CRC-16 commands that were added in version 1.3 of the specification add
a 16 bit cyclic redundancy check (CRC-16) to the returned data values. This provides an
additional means for the data recorder to ensure that the collected data has not been corrupted.
Software support for SDI-12 version 1.3 was added in software revision V2.0. All of the 5600-
0125-7 & -8, 56-0125-50-1 & -2, and the 5600-0124-1 versions of the ACCUBAR®
support the M
and C commands. The ones with software version 2.0 and higher also support the CRC-16 (MC
and CC) commands.
Selecting a measurement command class
Always supported
The first requirement is that the data recorder support the command. All SDI-12 data recorders
support the non-concurrent measurement M command. With the M command the data recorder
collects data from the sensors one at a time.
Multiple long measurement time sensors
When collecting data from several SDI-12 sensors that have long measurement times, the complete
data collection cycle can be shortened by utilizing concurrent commands. The data recorder can
initiate the measurement on all the sensors and when each finishes, then collect the data from all of

11
them. Since the measurement times overlap, the complete data collection cycle is shorter. There is
no advantage to the concurrent measurement C command when there is only one sensor.
Improved data integrity checking
The measurement command classes with CRC-16 (MC and CC) offer additional data integrity
checking over the non CRC-16 commands (M and C). The non CRC-16 commands offer data
integrity checking in the form of parity and the SDI-12 command structure. The CRC-16
commands offer some additional data integrity through the addition of a CRC-16. Since the CRC-
16 commands are brand new in SDI-12 version 1.3, not as many data recorders support them. In
most applications, lack of this support on the part of the data recorder will not be missed since non
CRC-16 SDI-12 commands still offer significant data integrity checking. If the data recorder
supports CRC-16 commands, then it is recommended to use them when collecting data from this
sensor in order to benefit from the increased noise immunity.
Making a non-concurrent Measurement (M command)
The command to tell the ACCUBAR®
to make a measurement with the original measurement
command is:
aM! where a is the address character, and M is the command to
make a measurement
Most data recorders will issue this command and automatically handle the reply to collect data.
You can also issue the command yourself. In reply, the ACCUBAR®
will respond with
attt2 acknowledging it is address a and indicating that after ttt
seconds are allowed for the measurement, 2 values can be
collected.
When the measurement is complete, the ACCUBAR®
responds with a service request
a where a is the address character
Note that you still do not have any data from the ACCUBAR. To request the data after a
measurement,
aD0! where a is the address character and D0 is the command to
retrieve measured data. Note: the number zero follows D,
not the letter O.
In this case, the ACCUBAR®
will reply with two values in the format:
avu
where a is the address, v is the data value and u indicates the
units. Both v and u have the format of a polarity sign (+ or −)
followed by up to seven digits, including a decimal point.
The u indicates the units of the measurement. When u is 0, the value has units of feet of water.
When u is 1, the units are psi. When u is 9, the units depend on a user entered slope and offset. u

12
can also take on additional values after a field calibration has been performed. The following table
summarizes all the values of u.
0 units are feet of water
1 units are psi
2 units are kilopascals
3 units are cm of water
4 units are m of water
5 units are mm of water
9 units depend on user-entered scale and offset.
If the field calibration offset is non-zero, then one of the following values of u will be returned:
10 units are feet of water with non-zero field calibration offset
11 units are psi with non-zero field calibration offset
12 units are kilopascals with non-zero field calibration offset
13 units are cm of water with non-zero field calibration offset
14 units are m of water with non-zero field calibration offset
15 units are mm of water with non-zero field calibration offset
19 user units with non-zero field calibration offset
(psi + field calibration offset) ∗ user scale + user offset
set by XE or XS set by XUU set by XUU
If the unit has had its calibration modified at a standards lab other than at Sutron, then the value
returned for u will have one hundred (100) added to it. In other words, if the XC command has
been utilized to set the calibration scale factor to other than 1 or the calibration offset factor to
other than 0 then 100 will be added to the units indicator.
In most cases, you will not set up the recorder to store this units identifier. It is provided in
response to the standard measure command to eliminate confusion as to the computation used to
come up with the final value.
Making a Concurrent Measurement (C command)
The command to tell an ACCUBAR®
to make a concurrent measurement is:
aC! where a is the address character, and C is the command to
make a concurrent measurement
The concurrent measurement command was first defined in version 1.2 of the SDI-12
specification. Therefore the data recorder will have to be SDI-12 version 1.2 or higher compliant
before it can be expected to issue this command and automatically handle the reply to collect data.
You can also issue the command yourself. In reply, the sensor will respond with
attt02 Acknowledging it is address a and indicating that after ttt
collected.
When the measurement is complete, the sensor does NOT issue a service request Note: this is
different from the M command.
To request the data after a measurement,

13
not the letter O.
In this case, the ACCUBAR®
will reply with two values in the format:
avu
where a is the address, v is the data value and u indicates the
units. Both v and u have the format of a polarity sign (+ or −)
followed by up to seven digits, including a decimal point.
1 units are psi
4 units are meters of water
14 units are meters of water with non-zero field calibration offset
Making a non-concurrent Measurement with CRC-16 (MC command)
to make a non-concurrent measurement with a CRC-16
check on the data is:
aMC! where a is the address character, and MC is the command to
make a non-concurrent measurement with a CRC-16

14
The non-concurrent measurement with CRC-16 command was first defined in version 1.3 of the
SDI-12 specification. Therefore the data recorder will have to be SDI-12 version 1.3 or higher
compliant before it can be expected to issue this command and automatically handle the reply to
collect data. You can also issue the command yourself. In reply, the ACCUBAR®
will respond
with
collected.
When the measurement is complete, the sensor responds with a service request
a where a is the address character
Note that you still do not have any data from the ACCUBAR®
. To request the data after a
measurement,
not the letter O.
In this case, the sensor will reply with two values in the format:
avuC
where a is the address, v is the data value, u indicates the units,
and C is the CRC-16 encoded into 3 ASCII characters. Both v
and u have the format of a polarity sign (+ or −) followed by up
to seven digits, including a decimal point. The CRC-16 is
always the last three characters which are never a numeric digit.
1 units are psi

15
determine the final value.
Making a Concurrent Measurement with CRC-16 (CC command)
to make a concurrent measurement with CRC-16 check on
the data is:
aCC! where a is the address character, and CC is the command to
make a concurrent measurement with a CRC-16 check on the
returned data
The concurrent measurement with CRC-16 command was first defined in version 1.3 of the SDI-
12 specification. Therefore the data recorder will have to be SDI-12 version 1.3 or higher
compliant before it can be expected to issue this command and automatically handle the reply to
collect data. You can also issue the command yourself. In reply, the ACCUBAR®
will respond
with
collected.
When the measurement is complete, the sensor does NOT issue a service request Note: this is
different from the M and MC commands.
To request the data after a measurement,
not the letter O.
In this case, the sensor will reply with two values in the format:
avuC
where a is the address, v is the data value, u indicates the units
the value is expressed in, and C is the CRC-16 encoded into 3
ASCII characters. Both v and u have the format of a polarity
sign (+ or −) followed by up to seven digits, including a decimal
point. The CRC-16 is always the last three characters which are
never a numeric digit.

16
1 units are psi
Other Measurements
The SDI-12 standard allows for other measurement commands such as M1, M2 etc., other current
measurement commands such as C1, C2, etc., other non-concurrent measurements with CRC-16
such as MC1, MC2, etc, and other concurrent measurement with CRC-16 such as CC1, CC2, etc.
This unit maintains symmetry across all four classes of commands, that is, it returns the same
information to a C1 as it does to a M1 or a MC1 or a CC1. The ACCUBAR®
supports the
following optional measurement commands:

17
aM1!
aC1!
aMC1!
aCC1!
measure psi using factory calibration. Do not apply any user
scaling, field calibration or offsets. This returns 1 value and
the units are fixed to psi.
aM2!
aC2!
aMC2!
aCC2!
measure temperature (Celsius or Fahrenheit). This returns two
values: the temperature and the units. The units will be 0 for
Celsius and 1 for Fahrenheit.
aM3!
aC3!
aMC3!
aCC3!
measure user scale, user offset, field calibration offset. Use
this if you want to view the user-entered values that can affect
the value returned by the M, C, MC, and CC commands.
aM4!
aC4!
aMC4!
aCC4!
measure calibration lab scale and offset. Use this if you want
to view the calibration lab values that can affect the value
returned by the M, C, MC, and CC commands.
aM5!
aC5!
aMC5!
aCC5!
measure the quadrature scale factor, quadrature threshold,
quadrature step rate, and operating mode for the analog and
quadrature outputs.
(Version 2.0
and higher.)
aM6!
aC6!
aMC6!
aCC6!
Measure temperature and pressure. The output is the
concatenation of the M2 and M commands. Temperature,
temperature units, Pressure, Pressure units.
(Version 2.0
and higher.)
aM7!
aC7!
aMC7!
aCC7!
Measure psi and degrees C using factory calibration. Do not
apply any user scaling, field calibration or offsets. This
returns two values and the units are fixed to psi and degrees C.
Remember to issue the aD0! command after the measurement is complete in order to retrieve the
data.

18
Changing the Units
As noted above, the aM! command can return the pressure in several different units. The selection
of the units is made using the XUP command:
aXUP+n+d! where n is one of the selections from the following table and d
is the number of digits to the right of the decimal point.
N Type Units Comments
0 ft of water The conversion to feet of water uses the
factor 2.3073 ft per psi.
1 Psi pounds per square inch.
2 kPa kilo-pascals
3 cm of water The conversion formula is 70.3265 cm
per psi.
4 m of water The conversion formula is 0.703265 m
per psi.
5 mm of water The conversion formula is 703.265 mm
per psi.
9 user units The value has units that depend on the
values entered using the XUU command.
For example, the command
aXUP+0+2!
will specify the output to be in the default units (Feet of water) with a resolution of 2 decimal
places. The second parameter (2 in the example) is optional. If omitted, the resolution is not
changed.
Setting User Units
If you want the sensor to read out in units other than feet of water, psi, kPa, or cm of water, you
will need to use the XUP command to set the units to 9, user units. When user units are selected,
the software will use the equation:
output = psi * scale + offset
where scale and offset are values you can enter into the system.
The XUU command is used to enter the user scale and offset. The format of the command is:
aXUUso! where s is the signed scale and o is the signed offset.
For example, the following command will set the scale to 70.32 and the offset to 0.0, which are the
proper values to convert the psi to cm of water:
aXUU+70.32+0
Similarly, the slope and offset can be set to any values that will produce the desired units.
NOTE: Remember that both an XUU and an XUP command are required for the
ACCUBAR®
to report in user-defined units.

19
Field Calibration
The ACCUBAR®
may have a change in the calibration over time. The most common change is a
change in sensor zero (value read when the pressure is 0). Or the user may wish to enter a site
specific offset to account for a difference between the orifice line outlet and a datum. The
ACCUBAR®
has two commands that can be used to change the zero reading. The XE command
allows direct setting of an offset which will be added to the measurement:
aXEou!
where o is adjustment value with units u. u can have units
0=feet, 1=psi, 2=kPa, 3=cm, 4=m, 5=mm, and 9=user
units.
For example, the command:
aXE+0.02+0
would set the offset pressure to 0.02 with units of feet.
Note: Be aware that the XE command enters an absolute offset, not a delta offset. To attempt
using the XE command to have readings match would require issuing an XE command to zero the
offset first before a reading can be taken to determine the new required offset. For this reason, the
XE command is only recommended for setting a known offset or datum into the unit. To have the
ACCUBAR®
reading match another instrument, such as a staff gauge, the XS command is
recommended.
The other command used to set the offset is the XS command. This command causes the sensor to
make pressure readings and automatically compute a new offset. You can use this command only
if you vent the sensor to the atmosphere or have a stable, known pressure on the sensor. The
command has the format:
aXS!
or
aXSdu!
use this form only when the sensor is vented to the
atmosphere
use this form when the sensor is at a stable, known
pressure. The d represents the desired reading and u the
units.
For example, after venting the sensor to the atmosphere, the following command would cause a
new offset to be computed:
0XS!
If the sensor was under pressure and stable at 4.65 feet, the following command would adjust the
offset to ensure the 4.65-foot reading:
0XS+4.65+0!
If the sensor was under pressure and stable at 4.65 psi, the following command would adjust the
offset to ensure the 4.65-psi reading:
0XS+4.65+1!

20
When the ACCUBAR®
is done with the self-calibration, the new offset is stored into memory. A
subsequent aD0! command will display this offset. The offset can also be displayed using the M3
command. The returned value will be in the current units of pressure.
Configuring the Analog Output
Analog Output Range
The 5600-0125-8 and 56-0125-50-2 versions support an analog output. The output range is 0 to 5
volts. As shipped from the factory, this corresponds to 0 to 22 psig. The analog output is driven
by a 12 bit D/A converter. This means that the output changes in discrete steps of about 1.25 mV.
Analog transmission of data is less accurate than digital transmission. There are three contributors
to this error: Error in the transmitted value; noise and voltage drops picked up during transmission
through the cable; and conversion errors at the receiving end. For the Accubar, the error in the
transmitted value is going to be the error in the digital value plus a voltage error of the output. For
the receiving end (data recorder, logger, panel display), there is a quantization error plus an
accuracy error when the analog voltage is converted to a digital value. The best resolution of a 12
bit A/D on a 0 to 5 scale is 1.25 mV. If the scale is wider or the number of bits is less, then the
resolution is even coarser.
This suggests that most users will want to customize the output range to maximize the accuracy of
their equipment over the range of interest. The command to set the Analog Output range is the
aXARzf! Where a is the address character, XAR is the extended command to set the
analog range, z is the pressure in psi that is to correspond to 0.000 VDC, and f
is the pressure in psi that is to correspond to 5.000 VDC.
If the user wanted the output of the ACCUBAR®
to be 5 to 10 psi then the following command
would adjust the range.
0XAR+5+10!
If the user wanted the ACCUBAR®
to output V1 volts at pressure P1 and V2 volts at pressure P2,
then the following formulas would be used to determine z and f.
( )
V1V2
P1P2V1
P1z
−
−
−=
( )( )
V1V2
P1P2V15
P1f
−
−−
+=
For example, suppose we want the ACCUBAR®
to output 2V at 20 ft of water and 4V at 40 ft of
water. First we must convert feet of water to psi by dividing by 2.3073. This gives V1=2V,
V2=4V, P1=8.668, P2=17.336. Therefore
z = 8.668 - ( 2*(17.336 - 8.668) / (4-2) ) = 0
f = 8.668 + ( (5-2)(17.336 - 8.668) / (4-2) ) = 21.67
Our command would therefore be:

21
0XAR+0+21.67!
Converting Voltage to Pressure
The formula for converting the analog output voltage to pressure is:
Pressure = analog output * Slope + offset
where the slope is (5 volt pressure value - 0 volt pressure value) / 5
and the offset is the 0 volt pressure value.
For the above illustrated range of 2V at 20 feet of water and 4V at 40 feet of water the offset for
reading the pressure in psi would be z which was 0. The slope would be (f - z) / 5 which is: 4.334.
To compute the output in feet of water for this example, the slope would be 10 and the offset
would be 0.
The slope and offset for different units when the output is configured for the factory default of 0 to
22 psi is given in the following table:
UNITS Slope offset
psi 4.4 0
feet of water 10.152 0
kPa 30.337 0
cm of water 309.44 0
NOTE: The analog output voltage does take into account the field calibration offset (set by the XE
or XS commands).
Configuring the Quadrature Output
Setting the Quadrature Scale Factor, Threshold, and Step Rate
The quadrature output tracks the pressure as returned by the M command. The units of pressure
for the M command are user configurable with the XUP command. Changing the units of pressure
for the M command with the XUP command also changes the units of pressure for the quadrature
output. The quadrature scale factor is the number of steps the quadrature output takes per unit of
change of the input pressure. As shipped from the factory the default units for the M command is
feet of water. The factory default scale value is 1000. This means that the quadrature output steps
1000 times for every change in the input pressure of one foot. This means that the resolution of the
quadrature output as shipped from the factory is 0.001 feet of water. This is the scale factor
necessary to produce one rotation of the output shaft of the Sutron 5600-0126-1 chart drive per
foot of input change. If the ACCUBAR®
was being hooked up as a shaft encoder for a data logger,
the scale factor would usually be set to 100 since most incremental shaft encoders produce 100
steps per revolution.
The threshold level is utilized to minimize excess stepping by a chart drive and therefore conserve
power. If the difference between the measured pressure and the quadrature output is less than the
threshold level, the quadrature output is not changed. Once the difference between the measured
pressure and the quadrature output exceeds this threshold level, the quadrature output will be
stepped in order to eliminate this “error”. As shipped from the factory, the default value of the
threshold is 0.01. This means that once the measured pressure and the quadrature output differ by
0.01 feet of water, the output will be stepped to eliminate this error.

22
The interface to the Sutron 5600-0126-1 operates at the 0.001 foot level. This means that if the
threshold were set to zero then for every 0.001 foot of change detected by the Accubar, the stepper
would be stepped. This would cause excessive power consumption on the stepper side because it
would be attempting to track all the ripples in the water’s surface and all of the bubbles going
down the tube. To prevent this excessive power consumption the threshold is set to the level of
accuracy desired. This is usually on the order of 0.01 feet. If a particular installation was using a
stepper and was not interested in any changes under 0.05 feet, then the threshold could be changed
to 0.05 and a power saving would result from the decreased stepping. If the quadrature output was
run directly into a data logger where there is not any penalty from the excessive stepping, then the
threshold could be set to 0.
This command also supports setting the step rate for the quadrature output. The factory default for
the step rate is 100 steps per second. This corresponds to the maximum step rate for the Sutron
5600-0126-1 Chart Drive. This means that if the ACCUBAR®
detected a one foot change, then
the output would be ramped at the rate of 0.1 foot per second for 10 seconds (1000 steps divided
by 100 steps per second). If the ACCUBAR®
was connected to the shaft encoder input of a data
logger the user might want to increase the step rate if the data logger could track a faster rate.
Likewise it can be decreased for slower devices. NOTE: Decreasing this number will result in
increased power consumption for the 5600-0126-1 Chart Drive, not lower power consumption.
The format for the command is:
aXQSstr! where a is the address character, XQS is the extended command to set the
Quadrature Scale Factor s in steps per unit of change as returned by the M
command, the Quadrature Threshold t, and the Quadrature Step Rate r in steps
per second.
If a user wanted to setup an ACCUBAR®
at address 3 to produce 1000 steps per foot (units of
pressure are 0 for feet of water), with a 0.01 foot threshold and a step rate of 100 steps per second,
the command would be:
3XQS+1000+0.01+100!
If the user wanted to connect it to a data logger that expected an incremental encoder that with a
resolution of 0.01 feet and could track a rate of change of 2 feet per second then the command
would be:
3XQS+100+0+200!
This represents a command to the ACCUBAR®
at address 3 to produce 100 steps per unit of
change (units of pressure, XUP command, is 0 for feet of water), no threshold, and to produce 200
steps per second (200/100 or 2 feet per second).
Setting the Quadrature Output’s Reading
The Quadrature output is an incremental output. It indicates a change in the value, it does not
report an absolute value. The device the ACCUBAR®
is connected to will have some indication of
what it thinks the current reading is. To facilitate synchronizing the quadrature input device with
the true pressure reading of the Accubar, the ACCUBAR®
has an extended command to set the
quadrature output to the current reading of the quadrature input device. The XQC command
causes the ACCUBAR®
to drive the quadrature input device to match the reading of the Accubar.
aXQCv! where a is the address character, XQC is the extended command to set the
Quadrature Current value where v represents the quadrature value as indicated
by the quadrature input device.

23
Once the XQC command is given, the ACCUBAR®
knows the level as perceived by the quadrature
input device. The next time the ACCUBAR®
complete a pressure measurement, it will check and
see if the difference between the input value and the measured pressure exceeds the threshold level
set by the XQS command. If so, it will drive the quadrature output to update the quadrature input
device.
NOTE: If the XQS command needs to be given (M5 command returns current value of Scale,
Threshold, Rate, and Operating Mode parameters), it should be issued with the correct parameters
before issuing an XQC command.
Use of an ACCUBAR
®
with a Sutron 5600-0126-1 Chart Drive
The 5600-0126-1 Chart Drive requires 1000 steps for one rotation of the shaft. The maximum
input step rate is 100 steps per second. The higher the quadrature threshold is set, the lower the
power consumption for the chart drive. The factory default settings of the ACCUBAR®
of 1000
for the scale factor, 0.01 for the threshold, 100 for the step rate, and Feet of Water as the units for
the M command will produce one shaft rotation per foot of water. To produce Clockwise rotation
of the shaft as viewed from the end of the shaft for increasing water level, connect Phase A to the
chart drive input labeled A, and Phase B to the chart drive input labeled B. For counter-clockwise
rotation, either reverse the connections (A to B, B to A) or enter the quadrature scale factor as
-1000.
If the ACCUBAR®
is only being used with the Chart Drive and not with a Data Logger, the Chart
Drive provides courtesy power outputs to power the Accubar. If the ACCUBAR®
is being used
with a Chart Drive and a Data Logger, then there must be a common ground connection between
the three devices. If a chart drive is being utilized with a data logger and an ACCUBAR®
providing an analog output to the Data Logger then steps must be taken to ensure that the Chart
Drive power consumption when stepping does not affect the analog reading. This means that there
must be a direct ground connection between the data logger and the Accubar. The Chart Drive can
not be connected to that ground. The Chart Drive must either have its own direct cable to the
battery, or be powered off of the power source for the data logger. It can not be powered off of the
line running to the Accubar.
Configuring the Operating Mode and Averaging Time
Setting the Operating Mode
The user can select the operating mode of the unit. There are two parameters that are either
enabled or disabled. The parameters are: quadrature output and background conversions. The
quadrature output can be either enabled or disabled. For units without quadrature output, it should
always be disabled. Background conversion affects both the quadrature output and the analog
output. If background conversion is enabled, the ACCUBAR®
will continually measure the
pressure and update its outputs accordingly. Background conversions add about 7 mA to the
quiescent power consumption. With background conversions disabled, the quiescent power
consumption of analog units drops to about 1 mA while for digital units it drops to about 0.2 mA.
Due to the increased power consumption, the background conversions should not be enabled
unless they are needed. If only the analog output or quadrature output is being used and SDI-12 is
not being used, then the background conversion must be enabled. If background conversions are
disabled then the outputs will only be updated if they are enabled and the ACCUBAR®
performs a
pressure measurement (an M, M1, or M2 command is issued).
If the ACCUBAR®
is being utilized for both SDI-12 and quadrature (or analog) outputs then the
user must decide whether they wish the auxiliary output (quadrature and/or analog) to match the
SDI-12 readings exactly or whether they should be updated independently of SDI-12. To be

24
updated independently means that background conversions must be enabled. To only be updated
when SDI-12 readings are performed, the background conversions must be disabled.
The form of the Command is:
aXOMm! where a is the address character, XOM is the extended command to set the
operating mode and m represents the operating mode.
The valid values for m are:
0 Quadrature output disabled and background operation disabled for analog units. (Low
quiescent power consumption for analog units being used as a digital only unit.)
8 Quadrature output enabled and background operation disabled. The quadrature output and
analog output will only be updated when a measurement command (M, M1, or M2) is
processed. (Low quiescent power consumption for analog units being used as a digital only
unit.)
16 Continuously update analog output. Quadrature output disabled (Normal operating mode for
an analog unit).
24 Quadrature output and background operation enabled. The quadrature and analog outputs will
be continuously updated. (This is a high quiescent power consumption mode).
Setting the Averaging Time
The ACCUBAR®
supports user selectable averaging time for SDI-12 readings. The time period in
seconds is specified with the aXT+t extended command.
For example, the command
0XT+10!
will set the averaging time to 10 seconds for an ACCUBAR®
at address 0.
Note: The averaging time is not the same as the time till completion of a reading. When the
ACCUBAR®
is awakened by the SDI-12 data recorder and a measurement is requested, the
ACCUBAR®
calibrates its internal A/D converter before taking the reading. This removes any
drift from the analog readings before the pressure measurement is started.
The ACCUBAR®
software supports two speed regions. If the requested time is less than 1 second
then the unit enters a higher speed mode. In the accurate mode (t >1) the noise floor of the
ACCUBAR®
is typically 0.0002 feet of water (0.00009 PSI), in the high speed mode it increases to
0.004 feet of water (0.002 PSI). In the accurate mode there is approximately a 3 second overhead
involved in the initial calibration before the ACCUBAR®
starts the pressure measurement
averaging. With the high speed mode the overhead drops to 0.4 seconds.
Note: It is recommended that a measurement be manually initiated (an M, M1, or M2 command)
after issuing the XT command to insure that the new coefficients are flushed through the
measurement system. This is particularly true with units operating in the background measurement
mode. Depending on when the XT command is issued with respect to the background
measurement, there is the possibility that the first reading after issuing the XT command will be
incorrect.
Resetting the unit to Factory Default Configuration
The ACCUBAR®
supports a reset to factory default command. The reset to factory defaults
command provides a means to reset most user configurable parameters in a unit back to the factory

25
defaults. If the previous history of a unit is not known, it is recommended that this command be
issued before configuring the unit to ensure a known starting configuration.
aXFD! where a is the address character, XFD is the extended command to reset the
unit to the factory default configuration. Note: The address is not changed.
Note: It is recommended that the unit be powered down and back up after issuing this command.
A reset to factory defaults sets:
• XUP: Pressure Units to Feet of Water
• XUT: Temperature Units to Degrees C
• XT: Averaging to one sample in slow mode
• XE: Offset to 0 (may have been previously set by the XS command)
• XQS: Quadrature threshold to 0.01, scale factor to 1000, and step rate to 100
• XOM: To factory default (dependent upon model).
• XOP: To automatically start making readings when an RS-232 connection is made.
• XAR: Resets analog output range 0V = 0 PSI, 5 V = 22 PSI
• XUU: Resets user scale factor to 2.3073 and offset to 0
Items not reset:
• Address
• Metrology lab calibration coefficients
• Resolution of pressure data returned as had been set by the XUP command.

26
5. Command Reference
This chapter documents the commands supported by the ACCUBAR. The commands are listed in
alphabetical order within a section.
Accubar Basic SDI-12 Commands
Command
Description
Command Syntax
(command underlined)
ACCUBAR
®
response (underlined)
"a" represents the
single-character address
Acknowledge
active
a! a
? Request
Address
?!
New in version 1.2 of SDI-12 spec.
Also see X? command.
a
indicating that the current address is a.
Note: ACCUBAR®
should be the only
sensor on the SDI-12 bus when this
command is given, otherwise there will
be a communications collision when all
units respond.
Ab Set SDI-12
address
aAb!
b new SDI-12 address
Example: 5A9!
(set address 5 to address 9, the
address was previously set to 5)
b
indicating that the new address is b.
Note: if the DIP switches are set to a
non-zero address then upon power-up
the address will be the dip-switch
address.
C Request
Default
Concurrent
Pressure
Measurement
aC!
aD0!
attt02
ttt is the time in seconds until the
measurement is ready, 02 is the number
of values that can be collected
axu
where x is the signed pressure value and
u is the signed indicator of the units.
The units are set by the XUP command.
C1 Request
Concurrent
Pressure
Measurement
in psi (factory
calibrated
value)
aC1!
aD0!
attt01
measurement is ready, 01 is the number
of values that can be collected.
ap
where p is the signed pressure value in
psi

27
Command
Description
Command Syntax
Sensor response (underlined)
"a" represents the
C2 Request
Concurrent
Temperature
Measurement
aC2!
aD0!
attt02
measurement is ready and 02 is the
number of values that can be collected
atu
where t is the temperature and u is the
units 0= Celsius and 1=Fahrenheit. Use
the XUT command to set the units.
C3 Request User
Scale, User
Offset, and
Field
Calibration
Offset
aC3!
aD0!
a00003
000 is the time in seconds until the
asoc
where, s is the user scale and o is the
user offset (psi), and c is the field
calibration offset (psi).
C4 Request
Standards lab
Calibration
Scale and
Offset
aC4!
aD0!
a00002
aso
where, s is the scale calibration and o is
the offset calibration(psi).
C5 Request
Quadrature
scale factor,
threshold,
step rate, and
operating
mode for the
unit
aC5!
aD0!
a00004
astrm
where, s is the Quadrature scale, t is the
quadrature threshold, r is the quadrature
step rate in steps per second, and m is
the operating mode of the analog and
quadrature outputs.

28
Command
Description
Command Syntax
"a" represents the
C6 Request
Concurrent
Temperature
and Pressure
Measurement
(Version 2.0
and higher)
aC6!
aD0!
attt04
atupv
where t is the temperature, u is the
temperature units, p is the pressure, and
v is the pressure units. Use the XUT
command to set the temperature units
and the XUP command to set the
pressure units.
C7 Request
Concurrent
factory
calibration
Pressure and
Temperature
Measurement
(Version 2.0
and higher)
aC7!
aD0!
attt02
apt
where p is the pressure psi and t is the
temperature in degrees Celsius.
CC Request
Default
Concurrent
Pressure
Measurement
with CRC-16
(Version 2.0
and higher)
aCC!
aD0!
attt02
measurement is ready, 2 is the number of
values that can be collected
axuC
where x is the signed pressure value, u is
the signed indicator of the units, and C is
the 3 character CRC. The units are set
by the XUP command.
CC1 Request
Concurrent
Pressure
Measurement
in psi with
CRC-16
(Version 2.0
and higher)
aCC1!
aD0!
attt01
values that can be collected.
apC
psi and C is the 3 character CRC
CC2 Request
Concurrent
Temperature
Measurement
with CRC-16
(Version 2.0
and higher)
aCC2!
aD0!
attt02
atuC
where t is the temperature, u is the units
0= Celsius and 1=Fahrenheit, and C is
the 3 character CRC. Use the XUT
command to set the units.

29
Command
Description
Command Syntax
"a" represents the
CC3 Request User
Scale, User
Offset, and
Field
Calibration
Offset with
CRC-16
(Version 2.0
and higher)
aCC3!
aD0!
a00003
asocC
user offset (psi), c is the field calibration
offset in the current pressure units, and C
is the 3 character CRC.
CC4 Request
Standards lab
Calibration
Scale and
Offset with
CRC-16
(Version 2.0
and higher)
aCC4!
aD0!
a00002
asoC
where, s is the scale calibration, o is the
offset calibration(psi), and C is the CRC.
CC5 Request
Quadrature
scale factor,
threshold,
step rate, and
operating
mode for the
unit with
CRC-16
(Version 2.0
and higher)
aCC5!
aD0!
a0004
astrmC
quadrature outputs, and C is the CRC.
CC6 Request
Concurrent
Temperature
and Pressure
Measurement
with CRC-16
(Version 2.0
and higher)
aCC6!
aD0!
attt04
atupvC
temperature units, p is the pressure, v is
the pressure units, and C is the CRC. Use
the XUT command to set the
temperature units and the XUP
command to set the pressure units.
CC7 Request
Concurrent
factory
calibration
Pressure and
Temperature
Measurement
with CRC-16
(Version 2.0
and higher)
aCC7!
aD0!
attt02
aptC
where p is the pressure psi, t is the
temperature in degrees Celsius, and C is
the CRC.

30
Command
Description
Command Syntax
"a" represents the
D0 Request Data aD0!
NOTE: This command is only issued
after a measurement command. It
should not be issued until the
measurement time has expired or a
service request has been received.
av
v contains the previously-requested
measurement values.
Example: 0 + 10.23 + 0
If the above example was received and
the previous measurement command was
an M, it would indicate that the water
level is at 10.23 feet.
NOTE: If the address is returned with no
data values, this indicates that there is no
data available. Either a measurement
command was not issued, the command
was aborted by sending a new command
before the measurement time expired, or
a service request was received.
I Send
Identification
aI! a13 SUTRON 0125-71.0sssssssVvvv
13 supports SDI version 1.3
commands
SUTRON manufacturer
0125-7 model number
1.0 hardware revision level
sssssss the sensor serial number
Vvvv the software revision
M Request
Default
Pressure
Measurement
aM!
aD0!
attt2
a
service request
axu
where x is the signed pressure value and
u is the signed indicator of the units.
The units are set by the XUP command.
M1 Request
Pressure
Measurement
in psi (factory
calibrated
value)
aM1!
aD0!
attt1
a
service request
ap
psi

31
Command
Description
Command Syntax
ACCUBAR
®
"a" represents the
M2 Request
Temperature
Measurement
aM2!
aD0!
attt2
a
service request
atu
where t is the temperature and u is the
units 0= Celsius and 1=Fahrenheit. Use
the XUT command to set the units.
M3 Request User
Scale, User
Offset, and
Field
Calibration
Offset
aM3!
aD0!
a0003
asoc
user offset, and c is the field calibration
offset. The field calibration is returned in
the current units.
M4 Request
Standards lab
Calibration
Scale and
Offset
aM4!
aD0!
a0002
aso
where, s is the scale calibration and o is
the offset calibration(psi).
M5 Request
Quadrature
scale factor,
threshold,
step rate, and
operating
mode for the
unit
aM5!
aD0!
a0004
astrm
quadrature outputs.

32
Command
Description
Command Syntax
ACCUBAR
®
"a" represents the
M6 Request
Temperature
and Pressure
Measurement
(Version 2.0
and higher)
aM6!
aD0!
attt4
a
service request
atupv
temperature units, p is the pressure, and
v is the pressure units. Use the XUT
command to set the temperature units
and the XUP command to set the
pressure units.
M7 Request
factory
calibration
Pressure and
Temperature
Measurement
(Version 2.0
and higher)
aM7!
aD0!
attt2
a
service request
apt
where p is the pressure psi and t is the
temperature in degrees Celsius.
MC Request
Default
Pressure
Measurement
with CRC-16
(Version 2.0
and higher)
aMC!
aD0!
attt2
a
service request
axuC
where x is the signed pressure value, u is
the signed indicator of the units, and C is
the 3 character CRC. The units are set
by the XUP command.
MC1 Request
Pressure
Measurement
in psi with
CRC-16
(Version 2.0
and higher)
aMC1!
aD0!
attt1
a
service request
apC
psi and C is the 3 character CRC

33
Command
Description
Command Syntax
"a" represents the
MC2 Request
Temperature
Measurement
with CRC-16
(Version 2.0
and higher)
aMC2!
aD0!
attt2
a
service request
atuC
where t is the temperature, u is the units
0= Celsius and 1=Fahrenheit, and C is
the 3 character CRC. Use the XUT
command to set the units.
MC3 Request User
Scale, User
Offset, and
Field
Calibration
Offset with
CRC-16
(Version 2.0
and higher)
aMC3!
aD0!
a0003
asocC
user offset (psi), c is the field calibration
offset (current pressure units), and C is
the 3 character CRC.
MC4 Request
Standards lab
Calibration
Scale and
Offset with
CRC-16
(Version 2.0
and higher)
aMC4!
aD0!
a0002
asoC
where, s is the scale calibration, o is the
offset calibration (psi), and C is the 3
character CRC.
MC5 Request
Quadrature
scale factor,
threshold,
step rate, and
operating
mode for the
unit with
CRC-16
(Version 2.0
and higher)
aMC5!
aD0!
a0004
astrmC
quadrature outputs, and C is 3 character
CRC.

34
Command
Description
Command Syntax
"a" represents the
MC6 Request
Temperature
and Pressure
Measurement
with CRC-16
(Version 2.0
and higher)
aMC6!
aD0!
attt04
a
service request
atupvC
temperature units, p is the pressure, v is
the pressure units, and C is the 3
character CRC. Use the XUT command
to set the temperature units and the XUP
command to set the pressure units.
MC7 Request
factory
calibration
Pressure and
Temperature
Measurement
with CRC-16
(Version 2.0
and higher)
aMC7!
aD0!
attt02
a
service request
aptC
where p is the pressure psi, t is the
temperature in degrees Celsius, and C is
3 character CRC.
R0
R1
.
.
.
R9
Request
Continuous
Measurement
Readings
aR0!
aR1!
.
.
.
aR9!
a
Unit only returns its address because it
does not support continuous
measurements.
V Initiate Verify
sequence
aV!
aD0!
attt5
indicating that the command will be
complete in ttt seconds and 5 values can
be collected.
a
service request
arespu
where r is the ROM checksum, e is the
EEROM checksum, s is the number of
resets since power up, p is the number of
power ups, and u is the number of
unexpected interrupts.

35
Accubar Extended Commands
Command
Description
Command Syntax
"a" represents the
X? Request
unknown
address
*X?!
This command causes any Sutron
ACCUBAR®
to identify itself. If you
have more than one ACCUBAR®
connected, the result may be garbled.
There is no guarantee that non-
ACCUBAR®
devices will respond to
this command.
a
Accubar’s address.
XAD Set SDI-12
address
(Sutron
extended
version) see
A command
for SDI-12
standard
version.
aXADnAn!
n new SDI-12 address, repeated
twice
Example: 5XAD9A9!
(set address 5 to address 9, the
address was previously set to 5)
a0011
no response if addresses do not match
Note: if the DIP switches are set to a
non-zero address then upon power-up
the address will be the dip-switch
address.
Note: a D0 command issued to the new
address after the XAD command will
return the new address.
XE Set Field
Calibration
offset
aXExu!
where x is the pressure offset
u indicates the units of the offset,
0 = feet water, 1 = psi.
Example: 0XE-0.05+0
(set offset to -0.05 feet)
Note Version 2.0 and later: Offset
can be queried by issuing aXE!
Followed by a aD0!
a0011
indicating that the command will take 1
second and 1 value can be collected.
A
service request
Note: a D0 command issued after the
XE command will return the offset in
units of psi for software versions before
2.0. Version 2.0 and later return the
offset in the current units of pressure.
XFD Reset to
Factory
defaults
aXFD!
This command resets most user
configurable configuration items
back to the factory defaults. It does
not reset the address nor does it affect
metrology lab calibrations.
Note: It is recommended that the unit
be powered down and back up after
use of this command.
a0101
indicating that the command will take 10
seconds and 1 value can be collected.
a
service request
XFD command will return the operating
mode

36
Command
Description
Command Syntax
ACCUBAR
®
"a" represents the
XOP Set Operating
Parameters
(Version 2.1
and higher)
aXOPp!
where p is the desired operating
parameter to be set.
values for p
0 Factory default condition which
starts reporting pressure readings
when an RS-232 connection is
made.
1 Disable automatic reading mode
for RS-232
All input values are standard SDI-12
values with polarity sign
attt1
where ttt indicates the command will be
complete in ttt seconds and 1 indicates
one value can be collected.
XOP will return the current operating
parameters.
XS Self-Cal the
Field
Calibration
Offset
aXS! or aXSdu!
where d and u are optional. When
omitted, the sensor is assumed to be
vented to the atmosphere. When
supplied, d is the desired reading for
the sensor and in the units indicated
by u. The ACCUBAR®
will make a
measurement and adjust the field
offset to ensure the reading matches
the value entered.
Example: 0XS!
(sensor is vented, adjust sensor to
read 0)
Example: 0XS+7.87+0
(sensor is at 7.87 feet, adjust offset to
ensure this reading)
attt1
where ttt indicates the command will be
complete in ttt seconds and 1 indicates
one value can be collected.
Note: a D0 command issued after XS is
complete will display the new offset in
units of psi for software versions prior to
2.0. Version 2.0 and later return the
offset in the current units of pressure.
The offset can also be displayed using
the M3 command.
XT Set
Averaging
Time
aXT+t!
t = averaging time in seconds (0 to
240 seconds)
Example: 0XT+10!
(sets the averaging time to 10
seconds)
a0011
indicating the command will be complete
in 1 second and 1 value can be collected
XT will return the number of samples to
be averaged during the selected time.

37
Command
Description
Command Syntax
ACCUBAR
®
"a" represents the
XUP Set pressure
units
aXUP+n+d!
n = 0 feet water
n = 1 psi
n = 2 kPa
n = 3 cm water
n = 4 m water
n = 5 mm water
n = 9 user units
d = number of places right of the
decimal (optional parameter)
Example: 0XUP+9+2!
Select user units with 2 right digits--
(make sure you use XUU command
to set the scale and offset for the
desired user units)
a0012
indicating the command will be complete
in 1 second and 2 values can be collected
XUP will return the value of the units
that are selected and the number of digits
right of the decimal point.
Note Version 2.0 and higher: Current
settings can be queried by issuing the
aXUP! Command followed by the aD0!
Command.
XUT Set
temperature
units
aXUTn!
n = 0 for Celsius,
n = 1 for Fahrenheit
Example: 0XUT1!
(set temperature units to F)
Note Version 2.0 and higher:
Current settings can be queried by
issuing the aXUT! Command
followed by the aD0! Command.
a0011
indicating the command will take 1
second to complete and 1 value can be
collected.
XUT will return the value of the units
that are selected.
XUU Set User
Units
aXUUso!
where s is the pressure scale factor
and o is the offset,
User output = (psi)*scale + offset
Example: 0XUU+27.63+0
(27.63 inches per psi)
issuing the aXUU! Command
followed by the aD0! Command.
a0012
Note: a D0 command issued after XUU
will return the scale and offset.
Note: a scale of 0 is invalid.
Note: Be sure that the units of pressure
(XUP) are set to user units (9).

38
Additional commands for Analog output units
Command
Description
Command Syntax
ACCUBAR
®
response
(underlined)
"a" represents the single-
character address
XAR Set Analog
Output range
aXARzf!
Where z is the pressure in psi to be
represented by
0.000 VDC
f is pressure in psi to be
represented by 5.000 VDC
All input values are standard
SDI-12 values with polarity sign.
a0012
indicating the command will be
complete in one (1) second and that
two (2) values can be collected.
NOTE: A D0 command issued after
the XAR will return two (2) values
representing the pressure range that the
user has selected.
issuing the aXAR! Command followed
by the aD0! Command.
XAO Set Analog
Output to a fixed
voltage
aXAOv!
where v is the required output in
VDC
SDI-12 values with polarity sign
a0011
indicating that the command will take
one (1) second to complete and that
one (1) value can be collected
the XAO command will return the D/A
value corresponding to the requested
voltage.
The unit's output will not act as a
pressure sensor again until this same
command is given with a negative
voltage request.
XOM Set operating
mode
NOTE: This
command also
affects
quadrature
output. For
these models
refer to the
XOM command
in the next
section.
aXOMm!
where m is the desired operating
mode.
values for m
0 Background operation
disabled. (Low quiescent
power consumption for analog
units being used as a digital
only unit.)
16 Continuously update analog
output.
attt1
Indicating that the command will take
ttt seconds to complete and that one (1)
value can be collected
the XOM command will return the set
operating mode.
issuing the aXOM! Command followed

39
Additional commands for Quadrature output units
Command
Description
Command Syntax
ACCUBAR
®
response
(underlined)
character address
XOM Set operating
mode
aXOMm!
where m is the desired operating
mode. Values for m:
0 Quadrature output disabled and
background operation disabled
for analog units. (Low
quiescent power consumption
for analog units being used as a
digital only unit.)
8 Quadrature output enabled and
background operation disabled.
Quadrature output and Analog
outputs will only be updated
when a measurement command
(M, M1, or M2) is processed.
(Low quiescent power
consumption for analog units
being used as a digital only
unit.)
16 Continuously update analog
output. Quadrature output
disabled.
24 Quadrature output and
background operation enabled.
Quadrature and Analog outputs
will be continuously updated.
(This is a high quiescent power
consumption mode).
attt1
ttt seconds to complete and that one (1)
value can be collected
the XOM command will return the set
operating mode.
issuing the aXOM! Command followed
XQC Set Quadrature
Output’s Current
Value
aXQCv!
where v is the value currently
indicated by the quadrature input
device
a0011
one (1) second to complete and that
one (1) value can be collected
the XQC command will return the
specified value.

40
Command
Description
Command Syntax
ACCUBAR
®
response
(underlined)
character address
XQS Set Quadrature
Scale factors
aXQSstr!
where s is the number of steps to
be output per a full unit of pressure
change as set by the units of
pressure (XUP command)
t is error threshold which must be
exceeded before the unit will start
stepping.
r is the step rate expressed in steps
per second. (optional)
SDI-12 values with polarity sign.
a0013
indicating the command will be
complete in one (1) second and that
three (3) values can be collected.
the XQS will return three (3) values
representing the quadrature scale
parameters the user has selected. The
rate will be expressed as number of
2µS time ticks between each step. Use
the M5 command to see the value in
terms of a rate.
issuing the aXQS! Command followed

41
6. Installation
The ACCUBAR®
will return accurate and reliable pressure data in any mounting position. We
recommend, however, mounting the sensor with the tubing connector and cable connector pointing
downward. This will prevent any moisture from following the cable or tubing down to the
ACCUBAR®
sensor.
The ACCUBAR®
mounts to a panel or surface through two holes that are accessible under the
sensor cover. The through-holes accommodate #8, #6 or M4 hardware.
The ACCUBAR®
pressure fitting accommodates an 1/8" OD tubing.
Warning: do not connect the ACCUBAR®
to a pressure source greater than the
rated pressure. Pressures in excess of rated pressure can alter the calibration of the
sensor and damage the unit. For 5600-0125-7 & -8, do not connect to a pressure
source greater than 35 psi. For the 56-0125-50-1 & -2, do not connect to a pressure
source greater than 100 psi.
It is important to check for leaks when installing the sensor. To check for leaks, pressurize the
system and then turn off the pressure source and the measurement outlet to allow the system to
stabilize. The pressure indicated by the sensor should hold constant when the supply to the sensor
is sealed.
Note: There may be small fluctuations due to thermal and other effects. A leak would be
indicated by a significant and continual decrease in pressure.

42
7. Calibration
The Accubar under goes a rigorous screening and testing at the factory before it is shipped to ensure that it
meets the accuracy specifications over temperature and that it is stable both in zero and span and will
continue to be accurate over time. Any drift in the zero of the unit can be easily checked by opening the
input to atmosphere and performing a measurement. Any drift can be nulled out via the XS command.
Span drift is much more difficult to determine. The span drift of the ACCUBAR®
in the field is typically
less than 0.01% per six months. This is a small fraction of the stated accuracy of the Accubar. The stated
accuracy of the ACCUBAR®
at its full scale reading is 0.1% of reading, although typically it is much better.
Even though it would typically take over 5 years for the ACCUBAR®
to drift as much as 0.1%, it is
recommended that the Accubar, like all precision measurement instruments, be placed on a periodic
calibration schedule.
Factory Calibration
The initial factory calibration typically includes over 1000 different pressure temperature points that cover
the complete temperature range from -40 to +60 degrees C and cover the complete pressure range from 0 to
22 PSI. This ensures that the ACCUBAR®
meets the specifications over the complete pressure and
temperature range. A calibration verification encompasses nearly 200 points over the complete temperature
and pressure range. An Accubar can be sent back to the factory for a complete calibration over
temperature. The Sutron Part number for this calibration service is: 8700-0005
Metrology Lab Calibration
The ACCUBAR®
does have the provision for a calibration to be performed by a Metrology Lab. The
calibration coefficients that can be entered by a metrology lab are a scale and an offset parameter. There is
not a provision for any temperature dependent parameters. Most metrology labs would not have the
capabilities to provide a calibration over temperature and pressure. To accurately calibrate an ACCUBAR®
requires a reference accuracy on the order of 0.001 PSI (8 Pa).
To collect data for calibration of the Accubar, the M1 command should be utilize. This will ensure that
field offset or old calibration coefficients do not affect the accuracy of the data collected. The command
that is utilized to enter the Metrology Lab Coefficients is:
aXCosc! where a is the address character, XC is the extended command to set the
calibration coefficients, o is the offset in PSI, s is the scale factor, and c is the
checksum.
The Checksum is the 8 bit sum of the 7 bit ASCII characters (parity is striped) from and including the
address character through the last character of the scale factor. It does not include the checksum string nor
its delimiting polarity sign. The checksum is transmitted as an ASCII string. That means that if the 8-bit
sum is 236 then the value of c is +236. The command to set the offset of the unit at address 0 to 0.0000 and
the scale factor to 1.0000 would be:
0XC+0+1+130!
The calibration coefficients affect the output of the M command, the RS-232 output, the analog output, and
the quadrature output. This command does not affect the output of the M1 command. The data output by
the M command is computed from the following equation:

43
Pressure = units offset + units scale * (field offset + calibration scale *(press. in PSI - calibration offset))
where:
press. in PSI is the factory calibration pressure as returned by the M1 command.
calibration offset is entered by the XC command
calibration scale is entered by the XC command
field offset is entered by the XE or XS commands
units scale and units offset are set by the combination of the XUP and XUU commands.
Note: Calibration scale and calibration offset can be determined via the M4 command.
Note: The current value of field offset, user units offset, and user units scale can be determined via the M3
command.

44
8. Troubleshooting and Maintenance
Troubleshooting
The following checklist will help in troubleshooting problems:
Problem Possible Cause
No data Faulty wiring -- check all wiring and terminations
No power -- check fuse in the data recorder and power at
sensor. There is no fuse in the sensor itself.
Wrong address requested -- make sure the data recorder is set
up to request data at the proper address
Wrong address set in sensor -- use the identify command to
make sure the sensor is responding to the proper address, if
not double check internal address dip switches since on
power-up they override any address set by the software.
Command or address is wrong case -- all ACCUBAR®
commands are capital letters, make sure address is proper
case and commands are upper case.
With RS-232, make sure that Transmit Data and Receive
Data are not reversed.
Garbled data Multiple sensors set to the same address -- check address
settings of all SDI sensors. Remove all other sensors from
the recorder and add them one at a time. Communication is
defined to be 1200, E, 7, 1.
Command issued to a wild card address (* or ?). Remove all
other sensors from the recorder and try again.
Erroneous data Wrong units selected -- use the M command and look at the
units field. Verify that the desired units are selected.
Erroneous offset entered -- display the field calibration offset
using the M3 command and verify it. Re-calibrate the offset.
Erroneous user scale and offset entered -- display the user
scale and offset using the M3 command and verify.
CAUTION: Do not remove the microprocessor from the ACCUBAR®
for any
reason. If there is a problem with the processor, please notify Sutron
Customer Service at (703) 406-2800. Only factory-trained personnel with
specialized tools can remove the microprocessor without damaging the unit
and the processor.
Also note that each microprocessor has been characterized for the specific
unit in which it is placed; THEY ARE NOT INTERCHANGEABLE.
Additional Troubleshooting commands
Measure Break detect time
The SDI-12 specification requires that all sensors ignore breaks less than 6.5mS and states that
they must detect breaks that are at least 12mS in length. There is an RS-232 command for the unit
to measure its break detect time. The unit should be completely disconnected from the SDI-12 bus

45
and the command issued via the RS-232 interface. Note: The unit will ignore this command if
issued via SDI-12.
aXB! where a is the address character, XB is the extended command to measure the
break detect time.
Returns: adr where d is the break detect time and r is the break reset time
The break detect time should be between 6.5 and 8.5 milliseconds and the break reset time should
be less than 1 millisecond.
Test Analog output
aXAT+v+n! where a is the address character, XAT is the extended command to test the
analog output, v is the maximum value to output, and n is the number of
times to repeat the cycle.
It ramps the analog output down from the value indicated by v to 0 and then repeats the process n
times. The output signal when observed with an oscilloscope will be a saw tooth wave form when
the analog output is working properly. The valid range for v is 0 to 4095. The valid range for n is
0 to 255. Note: This command can only be issued over the RS-232 interface. If issued over the
SDI-12 interface it will be ignored. Note: A value of 0 for v will produce a zero volt signal while
a value of 4095 will produce a saw-tooth waveform that starts slightly above 5 volts and ramps to
zero.
Maintenance
Typical maintenance for the sensor consists of checking the wiring to make sure it is not corroded
or frayed, checking the tubing to make sure it is intact and leak-free, and checking or setting the
field calibration offset.
Maintenance should be performed at least every 6 months in order to insure that the sensor meets
the accuracy specifications.
The offset can be checked by venting the sensor to the atmosphere and taking a reading from the
sensor.
If the ACCUBAR®
has been subjected to more than its maximum pressure, the offset of the unit
should be checked as described above.

46
9. Specifications for 5600-0125 Gauge ACCUBAR
Dimensions 3.14" X 4.95" X 2.24" (excluding connectors)
Weight 1.5 lbs.
Range 0 to 22psi (0 to 50 ft of water)
Operating Temp Range -40°C to +60°C
Vibration 0.5g @ 10-50Hz
Max. Overpressure 35 psi
Accuracy
above 4.4 psi (10 ft of water) 0.1% of reading
4.4 psi and below 0.0044psi (0.01 ft of water)
Resolution (default) 0.001psi (0.001 ft of water) - user selectable
Supply Voltage +8 to +28VDC (reverse polarity protected)
Power Consumption (-7)
RS-232 (active) 24mA
SDI-12 (active) 7mA typ.
Quiescent (Continuous update) 7mA typ.
Quiescent (Background disabled) 0.2mA typ.
RS-232 (active) 29mA
SDI-12 (active) 8.5mA typ.
Quiescent (Continuous update) 8.5mA typ.
Quiescent (Background disabled) 1mA typ.
Output -7 RS-232, SDI-12, and Quadrature
-8 RS-232, SDI-12, Quadrature, and Analog 0-5 VDC
RS-232 Data Output Continuous or on-demand
Communication Rate 1200 baud, Even Parity
Units Supported ft H2O, cm H2O, m H2O, mm H2O, psi, kPa,
and user defined
Pressure Fitting Fitting for 1/8" OD tubing. For alternate size fittings,
consult factory.
Overpressure Protection Internal Blow-off valve. Trips at 30 PSI nominal
Electrical Connectors -7, & -8 Terminal block and DB-9F
Media Compatibility Air or Dry Gas
Specifications subject to change without notice

47
10. Specifications for 5600-0124 Gauge ACCUBAR
Weight 1.5 lbs.
Range 0 to 22psi (0 to 50 ft of water)
Accuracy
above 4.4 psi (10 ft of water) 0.1% of reading
4.4 psi and below 0.0044psi (0.01 ft of water)
Power Consumption
SDI-12 (active) 7mA typ.
Quiescent (Continuous update) 7mA typ.
Quiescent (Background disabled) 0.2mA typ.
Output SDI-12
and user defined
consult factory.
Overpressure Protection Supplied by user externally (Sutron part number
6661-1210-1)
Electrical Connectors Terminal block

48
11. Specifications for 56-0125-50 Gauge ACCUBAR
Weight 1.5 lbs.
Range 0 to 50psi (115 ft or 35m of water)
Accuracy 0.05% FSO
RS-232 (active) 17 mA
SDI-12 (active) 6 mA typ.
Quiescent (Background disabled) 0.2 mA typ.
RS-232 (active) 18 mA
SDI-12 (active) 8.5 mA typ.
Quiescent (Continuous update) 8.5mA typ.
Quiescent (Background disabled) 1mA typ.
Output 56-0125-50-1 RS-232, SDI-12, and Quadrature
56-0125-50-2 RS-232, SDI-12, Quadrature, and Analog 0-5 VDC
RS-232 Data Output Continuous or on-demand
Communication Rate 1200 baud, Even Parity
and user defined
consult factory.
Electrical Connectors Terminal block and DB-9F

49
Appendix A -- Introduction to Pressure Measurement
TYPES OF PRESSURE MEASUREMENTS
ABSOLUTE (PSIA)
Pressure is measured with respect to an absolute vacuum.
DIFFERENTIAL (PSID)
Pressure is measured with respect to a second pressure port.
GAUGE (PSIG)
Pressure is measured with respect to atmospheric pressure.
Same as a differential pressure sensor with the second port open to
the atmosphere.

50
PRESSURE UNITS
GAUGE
PSIG or PSI pounds per square inch
Feet of water (USGS conversion factor is 2.3073 * PSI)
Meters of Water conversion based on density at 10°C
PRESSURE EQUIVALENTS
PSI feet of Water Meters of Water kPa
0 0.000 0.000 0.000
5 11.537 3.516 34.474
10 23.073 7.033 68.948
15 34.610 10.549 103.421
20 46.146 14.065 137.895
22 50.761 15.472 151.685
30 69.219 21.098 206.843
35 80.756 24.614 241.317
50 115.365 35.163 344.738
100 230.730 70.327 689.476

51
ERROR DEFINITIONS AND EXAMPLES
Linearity:
Linearity error is the deviation of the output from a straight line.
Many transducers for measuring physical phenomena have outputs
which do not vary linearly with the phenomena being measured.
Sometimes the deviation from linear is slight and is accepted as part
of the error of the device, in other cases manufacturers attempt to
"linearize" the output. Usually when this done through an analog
means, there will be a residual non-linearity, i.e., the non-linearity is
not completely removed. The following non-linearity graph illustrates
why a two point calibration (zero and full scale) is many times
insufficient and ensures that the maximum error is achieved. A best fit
straight line decreases the maximum error by ensuring that the errors
fall evenly on both sides.
Example of Linearity Error
-20
0
20
40
60
80
100
0 20 40 60 80 100
Input
Non-linear Output
Ideal Output
Best Fit
-

52
Temperature coefficient -- This is made up of two components, the temperature
coefficient of the offset and the temperature coefficient of the slope. These can be referred to as
thermal shifts, temperature dependence, and other names. The offset is sometimes referred to as
zero. The slope is sometimes referred to as span, sensitivity, or scale factor. The following graph
illustrates why the temperature coefficient is an important specification for remote equipment. In an
indoor environment a competitor's sensor is about a 0.1% FSO instrument. Over the operating
temperature range of Sutron equipment, it degrades to a +3.3% FSO instrument. The operating
error could be 33 times the stated single point accuracy. The Accubar’s accuracy is specified over
the entire temperature range, not at a single point.
Example Temperature error of a Competitor's 0.1% FSO
"Accurate" Sensor
-4.0%
-3.0%
-2.0%
-1.0%
0.0%
1.0%
2.0%
3.0%
4.0%
-40 -30 -20 -10 0 10 20 30 40 50 60
Temperature in degrees C
Errorbandin%FSO
Hysteresis - This is a measure of deviation in the output when passing through an
input point from two different directions. If a pressure transducer has zero pressure applied, then
10 PSI, then 22 PSI, then 10 PSI, the difference between the two 10 PSI readings would be a
measure of the pressure hysteresis of the transducer. Pressure transducers can also have
temperature hysteresis errors. Sometimes hysteresis is lumped in with other non-repeatability
errors.
ACCURACY - Accuracy is a measure of how closely the sensor's output matches the
"true" value of the parameter being sensed.
PRECISION - Precision is a measure of the repeatability of the sensor. It will most
always be better than the accuracy of the sensor.
RESOLUTION - The resolution of a sensor is the smallest change in the input that is
reflected in the output. For digital sensors it also refers to the smallest increment of the output.
This may be greater than or less than the sensor's resolution with respect to its input. Greater
resolution does not imply greater accuracy. Resolution and Accuracy are two independent
variables. The advantage of resolution in excess of accuracy is that changes in the input parameter
can be detected and tracked.

53
Appendix B -- SDI-12 with the Sutron 8200, 8200A, and 8210
Entering Extended Commands for Configuration Purposes
The Sutron 8200 family of data recorders supports the SDI-12 transparent mode. This allows the user to
issue commands to the sensor via the data recorder.
From the Front Panel
Go down the menu tree till you come to:
INSPECT SYSTEM
Go right and then down until you come to:
Enter SDI-12 Cmd
Press SET and then the unit will prompt you with:
Cmd:
At this point enter the command you wish issued over the SDI-12 bus. The command is entered via the arrow
keys. Remember that the address is always the first character of the command. The 8200 will append the ! to
the end of the command for you. When you have finished entering the command press SET and the 8200 will
send the command and display the response to the command.
From a PC connected to the RS-232 port
From the main menu select:
I - Inspect System
From the inspect system menu select:
E - Enter SDI-12 Commands
At this point you will be prompted to enter the command. Enter the command beginning with the unit’s
address and ending with an exclamation point (!). Do not forget the exclamation point. After entering the
command, press ENTER to send the command out over the SDI-12 bus. The 8200 will then display the
response to the command.
Logging data from the M1 or M2 commands or from addresses above 9
Beginning with version 3.3 of the software for the 8200 family, SDI-12 sensors can be renamed to allow any
SDI-12 address or measurement number to be specified. To remap an SDI-12 sensor from its default address
and parameter number you can use the form: SENSOR7a_p where SENSOR7 is the name you wish to give
the sensor (up to 7 characters), a is the address of the sensor "0" through "~", and p is the parameter number
"1" through "9".
EXAMPLE:
airtempA_1
would read parameter 1 from the SDI-12 device at address "A".
If you wish to use a measurement command other than the default aM!, then you can use the form:
SENS5a_pMm where SENS5 is the name you wish to give the sensor (up to 5 characters), a is the address of
the sensor "0" through "~", p is the parameter number "1" through "9", and m is the measurement command
to use.
EXAMPLE:
stage0_1M3
would use measurement command M3 to read parameter 1 from the SDI-12 device at
address 0.
Another feature is that you can define multiple sensors for the same SDI-12 parameter which will allow you
to define separate slopes, offsets, and other processing for the same parameter.

54
Logging Temperature data from the Accubar
Temperature data is the first parameter the ACCUBAR®
returns from the M2 command. Unless the units of
temperature have been changed from the factory defaults, the ACCUBAR®
will return the temperature in
degrees C. To log the internal temperature of an ACCUBAR®
that has been installed at address 5, the
following command must be issued:
5M2!
With the 8200 family the logged parameter came be named to help identify the data on future visits or upon
data retrieval. To issue the 5M2! command we are limited to a 5 character name. If “temp” is chosen as the
identifying name then the sensor should be named:
temp5_1M2
This name indicates that the M2 command should be issued to address 5 and the first parameter returned
should be logged.
Logging data with multiple data recorders
Setup two 8200s with one ACCUBAR
This setup allows for an ACCUBAR®
sensor to be logged in two 8200A at the same time.
8200A SDI-12 connector -->Pin 1 is Data, pin 7 is GND and pin 9 is +12V.
ACCUBAR®
RS-232 connector has same pinout as 8200A SDI-12 connector.
ACCUBAR®
round connector --> Pin A is Data, pin B is +12V and pin C is GND.
NOTE: Measurement time in one of the data loggers should be offset by 30 seconds with respect to the other
datalogger.

55
Setup two 8200s with two ACCUBARS
This setup allows for two ACCUBAR®
sensors to be logged in two 8200A at the same time.
8200A SDI-12 connector -->Pin 1 is Data, pin 7 is GND and pin 9 is +12V.
ACCUBAR®
RS-232 connector has same pinout as 8200A SDI-12 connector.
ACCUBAR®
round connector --> Pin A is Data, pin B is +12V and pin C is GND.
• Sensors must have different addresses.
• Measurement time in one of the data loggers should be offset by 30 seconds with respect to the other
datalogger.

57
Appendix C -- Procomm setup for use with the Accubar
Connect serial cable to DB-9 connector on Accubar.
Note: External power must be supplied to the Accubar. It can not be powered off of
the computers RS-232 port. External power can be supplied via the Terminal Block. It is
possible to supply power via the DB-9 connector but it would require a custom cable.
Refer to the RS-232 wiring section of the manual for full details.
Communications parameters should be 1200 E71.
Terminal emulation should be VT-100 or equivalent.
To be able to see the commands you type, make the following changes to the default setup.
- Change Duplex to HALF
Alt + S, then select 2 for Terminal Setup and change option 2 to HALF.
- Change Echo to YES
Alt + S, then select 6 for ASCII Transfer Setup and change option 1 to YES.
Procomm Plus requires an additional change in the setup.
<ALT-S> , setup menu. Now proceed to PROTOCOL OPTIONS,
then to GENERAL OPTIONS. Set selection C to "NO". This is the "Abort
transfer if CD lost". This needs to be NO!!!

Bringing the Benefits of Real-Time Data Collection to the World
Sutron Corporation, 21300 Ridgetop Circle, Sterling, Virginia 20166-6520
Appendix D -- Sutron Customer Service Policy
CUSTOMER SERVICE POLICY
Customer service often begins after the sale, usually when the customer has a question or problem. At Sutron
we are dedicated to providing unmatched Customer service before and after the sale.
Sutron Customer Service representatives routinely handle a wide variety of questions every day. Do you have
a sensor that you are not sure how to interface? Are you using a Sutron sensor with someone else's data logger
and are not sure how to connect it? Which telemetry options would be the most economical, yet still provide
you with the quality of data that you need?
We encourage customers to take advantage of our years of experience with equipment, systems, and services.
Our Customer Service representatives are electronic technicians with field and applications experience, not
just someone with a technical background. Sutron can answer most sensor or interface questions on the first
call. If Sutron cannot quickly answer a question on an interface, we will work with the customer to find a
solution. The solution may involve sending in the sensor for close examination by Sutron’s engineers.
Sometimes a customer’s problem is application specific. Although Customer Service prides itself on handling
95% of application related questions over the phone, we maintain constant contact with our Integrated
Systems Division. When a customer needs an engineer to back him up, we have Computer/Electrical
Engineers, as well as Hydrologist/Water resources, and Civil Engineering Services.
Of course not all problems can be fixed over the telephone. Sometimes a customer needs someone on-site
who can identify site related problems or troubleshoot a telemetry network. Sutron is happy to provide these
services at reasonable cost.
Training is an important part of Sutron Customer Service philosophy. Without the proper training our
customers cannot take advantage of the benefits and advantages that our equipment provide. We often
provide on-site introductory training at your facility for no charge. We also conduct in-house or on-site
format training classes for those customers who desire it. Refer to the Services Section of the Sutron catalog
for classes and call Sutron to schedule your training requirements.

Accubar multi interface gauge pressure sensor

More Related Content

What's hot (7)

Viewers also liked (20)

More from webadminjk (20)

Recently uploaded (20)

Accubar multi interface gauge pressure sensor