Analysis and Modification of Scissor Jack

@ IJTSRD | Available Online @ www.ijtsrd.com
ISSN No: 2456
International
Research
Analysis and Modification
Ekhalak Ansari, Udham Singh
Department of Mechanical Engineering
Jain University
ABSTRACT
Every manufacturing product requires cost efficient
method and its variation in application maintaining its
natural structure as well as assign service life keeping
failure parameters in mind we are focused on our
intention of designing, modifying and analyzing the
jack model for actual loads for varying models on
different applications. We are keen at making the
scissor jack cost effective and at the same time
maintaining its strength and life span. Also the new
design that made by SOLIDWORKS software can be
tested by ANSYS software. The overall strength of
the jack is relatively more compared to commercially
available screw jacks. Car jacks that are commercially
available has some disadvantages such as required
more energy to operate, not usable for aged people
and cannot be used on the uneven and rough surface.
The main purpose and significance of this paper is to
design, optimize and standardize the current toggle
jack to make the task easier and reliable.
Keywords: Scissor Jack, Ansys, Solidworks, Analysis,
Modification
1. INTRODUCTION
A jack is a mechanical device which is used
device in order to lift heavy loads or to apply great
forces for certain specific purpose. The most common
form of a jack is car jack, floor jack or
which lifts vehicles so that the operation can be
performed. A scissor jack is a device formed
cross hatch mechanism similar to that of
as to lift up a vehicle for
maintenance.
@ IJTSRD | Available Online @ www.ijtsrd.com | Volume – 2 | Issue – 4 | May-Jun
ISSN No: 2456 - 6470 | www.ijtsrd.com | Volume
International Journal of Trend in Scientific
Research and Development (IJTSRD)
International Open Access Journal
nd Modification of Scissor Jack
Ekhalak Ansari, Udham Singh, Vikas Jangid, P. S. Raghavendra Rao
Department of Mechanical Engineering School of Engineering and Technology,
Jain University, Bengaluru, Karnataka, India
Every manufacturing product requires cost efficient
application maintaining its
natural structure as well as assign service life keeping
failure parameters in mind we are focused on our
intention of designing, modifying and analyzing the
jack model for actual loads for varying models on
ns. We are keen at making the
scissor jack cost effective and at the same time
maintaining its strength and life span. Also the new
design that made by SOLIDWORKS software can be
tested by ANSYS software. The overall strength of
compared to commercially
available screw jacks. Car jacks that are commercially
available has some disadvantages such as required
more energy to operate, not usable for aged people
and cannot be used on the uneven and rough surface.
ignificance of this paper is to
design, optimize and standardize the current toggle
jack to make the task easier and reliable.
Scissor Jack, Ansys, Solidworks, Analysis,
is a mechanical device which is used to lift
to lift heavy loads or to apply great
forces for certain specific purpose. The most common
or garage jack,
which lifts vehicles so that the operation can be
formed with a
of a scissor so
repair and
Fig.1: Scissor
The scissor jack has a screw
thus moves the two arms producing
The rotation of a screw thread
to lift a vehicle that weights
of pounds. We have used the traditional
make a certain modification and
analysis. The design of this device
user friendly. The addition of
more strength but does not occupy
can be again retracted back to
main advantage of this project
stability and strength. The final
modelled and provide new approach
2. Background Work
1) Norman J. Glomski, Kim K. Jackamn “Vertical
body with powered lift type tail gate”
to vehicle bodies with tailgate lifted to open and
close with minimal effort. It does so by providing
vehicle design a sideways type of swinging
tailgate that swings about vertical axis to open and
thus reduces the effort. It offers a simple, cost
effective, space saving, easy to install powered
Jun 2018 Page: 1960
6470 | www.ijtsrd.com | Volume - 2 | Issue – 4
Scientific
(IJTSRD)
International Open Access Journal
f Scissor Jack
S. Raghavendra Rao
School of Engineering and Technology,
Scissor Jack
thread which turns and
producing necessary work.
thread causes the scissor jack
weights several thousands
traditional scissor jack to
and then also work on its
device will make it more
of extra parts will add
occupy more space as it
its contact position. The
project is to improve the
final product will be newly
approach of modification.
Norman J. Glomski, Kim K. Jackamn “Vertical
body with powered lift type tail gate” This relates
to vehicle bodies with tailgate lifted to open and
. It does so by providing
vehicle design a sideways type of swinging
tailgate that swings about vertical axis to open and
thus reduces the effort. It offers a simple, cost
effective, space saving, easy to install powered

International Journal of Trend in Scientific Research and Development (IJTSRD) ISSN: 2456-6470
@ IJTSRD | Available Online @ www.ijtsrd.com | Volume – 2 | Issue – 4 | May-Jun 2018 Page: 1961
actuator that operates to lift tailgate with reduced
effort and also can be operated manually if
required.
2) Manoj R Patil, S D Kachave, “Design and
Analysis of Scissor Jack” This paper uses the
traditional scissor jack and deals with removal of
perm ant welds as chances of failure in that area is
more. These welds are replaced by rivets. Absence
of welds will give less deflection and large
accuracy. It also considers the cost estimation and
try to reduce unnecessary costs .the main objective
of this is to reduce no of parts by simplifying
assembly process, remove welding to avoid
distortion and reduce weight of jack by changing
manufacturability.
3) C.S Dhamak, D.S Bajaj, V.S Aher, G.Nikam,
“Design and Standardization of Scissor Jack to
avoid Field failure” In this Paper, a unique design
of scissor jack is compile to lift low as well as
heavy load with different conditions. The main
purpose and significance of this paper is to design,
optimize and standardize the current toggle jack to
make the task easier and reliable. Catia is used to
develop and analyze the scissor jack.
Mathematical model of design procedure is also
made which is supposed to help in standardization
of scissor jack design by using MATLAB.
4) Shoei D. Chang, Huey S. Liaw, “Motor driven
scissor jack for automobiles” This relates to use of
motor driven scissor jack which is using electric
power source from cigarette lightening socket of
any automobile. The DC motor is driven through
deceleration gear box for rotating screw rod
clockwise and anticlockwise for raising and
lowering of frame. It is also provided with one
ultimate switch thus limiting the peak and low
break points and prevent it from collapsing thus
increasing the safety of the operation.
5) C.S Dhamak, D.S Bajaj, V.S Aher, “Design and
optimization of Scissor Jack” This project aims at
designing and analysing scissor jack models for
various model of automobile. It changes the
original one and modify them without sacrificing
strength and service life. The failure mode is
studied and mathematical model is made
analytically as well as theoretically. The
modelling is carried out on CATIA and the
mathematical model is tested by ANSYS software
3. Problem Statement
 The traditional jacks require more strength in
order to lift any device and not suitable for aged
and handicapped people.
 Since the width of the base track of the jack is
less, it leads to instability during operation and
hence reduces work efficiency.
 The normal jacks will be manually operated and
hence it enhances risk and reduces safety.
 The welded joints increase tendency of
deflection and distortion and eventually lead to
failure.
 Due to the diamond shape of the jack, it is more
prone to failure and can be used mostly for
light-duty work.
4. Objectives
 To increase the width of the base by addition of
extra metal plates for improving the stability as
well as the strength.
 To modify the existing design in order to
increase the load bearing capacity.
 To make the jack automatically operated by
using a 12v motor that runs by car battery.
 To use a pneumatic gas spring that reduces the
effort required to lift the required equipment.
 To analyse and compare factors such as stress,
strain, deflection on both the traditional and
modified scissor jack by using ANSYS
software.
5. Methodology
Fig.5: Proposed System

5.1 Material Properties
All the jack devices are generally made up of mild
steel. So, the additional material that is considered for
this device is mild steel (structural steel) as it will
provide same operating properties. The material will
be completely designed on plain carbon steel. It
provides more resistance to the load before
undergoing any strain and deformation. The
pneumated gas spring is made up of aluminium and
thus is lighter. Some of the properties of materials that
are considered are given in the table below.
Fig.5.1: Material Properties
5.2 Experimental Methods
The design of this device is done on SOLIDWORKS
software and the necessary analysis is done on
ANSYS software. For the design part, the fine mesh is
used mostly as it is most common. After the design,
both the jacks (before and after) modification will
undergo analysis where factors such as stress, strain
and deflection are obtained and compared.
5.3 FINE MESH
Fig.5.3.1: Fine Mesh before modification
Fig.5.3.2: Fine Mesh after modification
5.4 ANSYS PROCEDURE
 Static-Structural (ANSYS)-(Double Click)
 Engineering Data-Add Material
 Geometry-Impart Geometry-Select material
(ok)
 Model-Edit (ok)
 Mesh-Sizing-Relevance Center-Fine
 Mesh-Update mesh
 Static-Structural-Insert-Fixed Support-
Select from model-Apply
 Static-Structural-Insert-Force- Select from
model-Apply
 Solution-insert-Deformation-Total

 Solution-Insert-Strain-Equivalent (Von
Mises)
 Solution-Insert-Stress-Equivalent (Von
Mises)
 Solution-Insert-Solve
6. Results And Discussions
Fig.6.1: Total deformation (Before modification)
Fig.6.2: Total deformation (After modification)
Fig.6.4: Equivalent Elastic Strain (Before
modification)
Fig.6.3: Equivalent Elastic Strain (After
modification)
Fig.6.5: Equivalent stress (Before modification)

Fig.6.6: Equivalent stress (After modification)
The results obtained shows significant increase in
stress bearing capacity thus ultimately increasing the
life span of the device. The strain obtained by
analysing the both parts indicates that the modified
one can prevent the elongation or change in physical.
The modified structure will provide more resistance to
any distortion as its deformation value is higher.
7. Conclusion
The Design and Analysis of the Scissor Jack is done
on SOLIDWORKS and ANSYS software. The model
of the traditional scissor jack is modified by using
several additional parts such as gas spring, metal
plates. The stress, strains and deformation are
calculated and compared to that of the normal one.
The compared result that has been obtained proved to
be optimized and has provided further scope of
improvements. The device has been made and it is
showing positive results. If it is made in a larger size,
it can further be utilized in an automotive as well as
other industrial sectors. The extra addition parts that
are added are cost effective and prove to be more
efficient. The newly formed device can be operated
automatically as well as manually which most of the
traditional scissor jacks are. It can be operated at even
non-uniform surfaces providing great extent of
stability. It significantly reduces the effort that is used
for the operation of the jack. This also occupies the
space very less as the gas springs can be folded very
compactly to the body. Overall, the performance of
the jack is enhanced and provide a great deal of future
use.
References
1. Norman J. Glomski, Kim K. Jackman, “Tailgate
Lift Mechanism”, May 13,1975, U.S Patent,
Patent Number 3,883,014
2. Manoj R Patil, S D Kachave, “Design and
Analysis of Scissor Jack”, International Journal of
Mechanical Engineering and Robotics Research,
Volume 04, Issue 01, January 2015, ISSN 2278-
0149
3. C.S Dhamak, D.S Bajaj, V.S Aher, G.Nikam,
“Design and Standardization of Scissor Jack to
avoid Field Failure”, International Journal of
Advance Research and Innovative Ideas in
Education, Volume 01, Issue 03, 2015, ISSN
2395-4396
4. Shoei D. Chang, Huey S. Liaw, “Motor driven
Scissor Jack for automobiles”, March 31,1987,
U.S Patent, Patent Number 4,653,727
5. C. S Dhamak, D.S Bajaj, V.S Aher, “Design and
optimization of Scissor Jack”, Technical Research
Organization India, Volume 02, Issue 01, 2016,
ISSN 2394-6202
6. S. Sasank Babu, “Fabrication of an innovative
scissor jack”, Indian Streams Research Journal,
Volume 05, Issue 04, May 2015, ISSN 2230-7850
7. Kamalakkannan. A, Kalaiselvan. P, Isaac. R,
Vijay. V, “Automatic motorised screw jack to
reduce man power”, International Journal of
Scientific and Engineering Research, Volume 07,
Issue 05, May 2016, ISSN 2229-5518
8. P.S. Borkar, V.sontakke, R. R. Dorwe, A.B.
Ganorkar, S. P. Lokahande, “Design of Pneumatic
Operated Jack for Four wheelers”, International
journal for Scientific Research and Development,
Volume 03, Issue 03, June 01,2015, ISSN: 2321-
0613

Analysis and Modification of Scissor Jack

More Related Content

What's hot (20)

Similar to Analysis and Modification of Scissor Jack (20)

More from ijtsrd (20)

Recently uploaded (20)

Analysis and Modification of Scissor Jack