Analysis of rc bridge decks for selected national a nd internationalstandard loadings using finite element method copy
0 likes219 views
The document analyzes the effects of different national and international standard loadings on reinforced concrete bridge decks using finite element modeling. 36 bridge deck models of slab bridges and T-beam bridges were analyzed under loadings from IRC, AASHTO, and Eurocode standards. The results show maximum differences of 5-15% in deflection and bending moment between IRC loadings, and 5-17% difference for AASHTO loading compared to IRC. Eurocode loading causes increases of 1.7-1.8 times for slab bridges and 1.3-2.2 times for T-beam bridges over IRC due to higher load magnitudes. Transverse and torsional responses also vary significantly between standards.
![IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 66
CONCLUSIONS
a. The maximum values of deflection and longitudinal
bending moment caused by IRC class A and 70R
wheeled vehicle do not differ by more than 7% for the
selected aspect ratios of Slab Bridge decks
investigated.The corresponding difference in case of T
beam decks is -22 to 37%.
b. AASHTO loading causes -7 to 17% higher deflection
and less than 5% in case of longitudinal bending
moment compared to IRC class A loading. While the
corresponding range is 1.7 to 1.8 times for EURO
loading.
c. In general maximum transverse and maximum torsional
moments are more pronounced in case of slab bridge
decks compared to T beam decks and are found to be in
the range of 15 to 20% and 30 to 40% respectively of
corresponding longitudinal moment in case slab bridge
decks and less than 5% of corresponding longitudinal
moment in case of T beam decks because of higher
transverse moment of inertia and torsional rigidity.
d. Because of their lower magnitude and thick solid
sections are adopted for the members the maximum
torsional moment and maximum transverse bending
moments may not have any major significance on the
design of slab bridge deck and T beam bridge deck.
e. The provision of T beam bridge decks instead of solid
bridge decks of same aspect ratio is found to reduce in
maximum deflection values by 25 to 30% and the
maximum longitudinal bending moment values are
reduced by 76 to 81%. Another major advantage is the
reduction in maximum torsional and maximum
transverse moments by 33 to 65%.
f. The study shows that there is a wide variation in the
highway bridge loading standards of different countries.
However the changes in critical response parameters
are not very significant. IRC has adopted 6 standard
loadings with widely varying magnitude of wheel
loading and wheel and axle spacing. However the
investigations indicate that there is no appreciable
difference in structural response parameters for the
different loadings. It is suggested that IRC may also
adopt the single design vehicle with simple
configuration for standard loading similar to AASHTO
and EURO standard loading which have only 2 to 3
axles.
REFERENCES
[1] P.K. Thomas “A Comparative Study of Highway
Bridge Loadings in Different Countries”supplementary
report 135UC, Transport and road research laboratory.
[2] Medhat Kamal Abdullah “Comparison between
Highway Codes for Traffic Loads on Bridges”Life
Science Journal 2013: PP.621-627.
[3] Dr.MaherQaqish, Dr.EyadFaddaand
Dr.EmadAkawwi“Design of T-beam Bridge by Finite
Element Method and AASHTO Specification”KMITL
Sci. Journal. Vol.8 No.1 January – June, 2008.
[4] KanchanSen Gupta and
SomnathKarmakar“Investigations on Simply supported
concrete bridge deck slab for IRC vehicle loadings
using finite element analysis”Journal of Earth Sciences
and Engineering, Volume 04, No 06 SPL, October
2011, PP. 716-719.
[5] IRC 6:2000 “Standard Specifications and Code of
Practice for Road Bridges, Section-II Loads and
Stresses”, Indian Road Congress, New Delhi.
[6] American Association of State and Highway
Transportation Officials (AASHTO) specifications.
[7] Eurocode 1 Part 2 - prEN 1991-2-2002.
[8] IRC 21:2000 “Standard Specifications and Code of
Practice for Road Bridges, Section-III Cement Concrete
(Plain and Reinforced)”,Indian Road Congress, New
Delhi.](https://image.slidesharecdn.com/analysisofrcbridgedecksforselectednationalandinternationalstandardloadingsusingfiniteelementmethod-c-161015104050/85/Analysis-of-rc-bridge-decks-for-selected-national-a-nd-internationalstandard-loadings-using-finite-element-method-copy-8-320.jpg)
Analysis of rc bridge decks for selected national a nd internationalstandard loadings using finite element method copy
- 1. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 59 ANALYSIS OF RC BRIDGE DECKS FOR SELECTED NATIONAL AND INTERNATIONALSTANDARD LOADINGS USING FINITE ELEMENT METHOD Hemalatha A1 , Ashwin K. N2 , Dattatreya J.K3 , S.V.Dinesh4 1 Post graduate Student, 2 Assistant Professor, 3 Research Professor, 4 Professor and Head, Department of Civil Engineering, Siddaganga Institute of Technology, Tumkur. hemacivil10@gmail.com, meetashwinkn@yahoo.com, jk.dattatreya@gmail.com, dineshsv2004@yahoo.com Abstract The paper presents the comparison of the effect of different standard loadings on a set of reinforced concrete bridge decks using the finite-element method. The parameters investigated include the aspect ratio (span/width) and type of loading. The investigations are conducted on two lane slab bridge decks of span 5m to 9.5m and two lane T beam bridge decks of span 7.5m to 20m. A total of 36 bridge models were analyzed. The variation of different critical structural response parameters such as deflection, longitudinal bending moment, transverse moment, shear force and torsional moments are evaluated for IRC loading (IRC Class A and 70R loadings), AASHTO loading (HL93) and Euro standard loading (LM1). The results shows that the maximum difference in deflection and longitudinal bending moment for the two IRC standard loading ranges from 5 to 15%. While the difference between corresponding values for the AASHTO loading in the range of 5 to 17%. The maximum axle load of euro standard loading is found to be 2.2 times higher than IRC class A loading maximum axle load hence the values of structural response parameters are increased by 1.7 to 1.8 times. Therefore there is a need for adopting simplified and more realistic standard loads in the future. Keywords: Bridges, Concrete deck slabs; Finite element method; T-beam bridge decks; Aspect ratio; Live load, IRC code, AASHTO code and Euro code. ---------------------------------------------------------------------***------------------------------------------------------------------------ 1. INTRODUCTION Vehicular loads constitute the most important type of loading to be considered in the design of bridges. Many countries have formulated their own standard specification and codes of practice for bridges such as IRC, AASHTO and EURO codes, with a view to establish a common procedure for the design and construction of bridges. Most of the prevailing standard loads including the IRC bridge loads have very little rational basis and lacking relevance to the current vehicular configuration plying on the roads and bridges. With growing tendency to overload the vehicle beyond the permitted legal axle load and also increase in vehicular traffic, it has become necessary to have a reappraisal of current bridge loadings of IRC to evaluate the safety of existing bridges and for the design of many new bridges for increased magnitude of loads and intensity of traffic. Reappraisal of the safety of existing bridges and design of new bridges is rather difficult in the Indian context due to complicated load pattern of different classes of load therefore there is a need to simplify the loading standards and adopt more realistic design vehicle in similar to that adopted by AASHTO and EURO code. Also the loading standards depends on different factors such as type of vehicle plying, their loading capacities, the intensity and frequency of traffic and logistic considerations for general mobilization in case of national emergencies. They may also have a bearing on the permissible stresses in materials and design methods in the country concerned. Therefore the comparisons made may not be viewed as strictly quantitative, it will be more reasonable to take them as reflecting the global trend of the global effects of the loadings on the bridge. Earlier investigation on comparative study of highway bridge loadings in different countries by Thomas(1975) concluded that there was a wide variation in the highway bridge loading standards of different countries and also Medhat Kamal Abdullah(2013) studied a comparison between different loading standards such as AASHTO, Egyptian and Euro code loadings and concluded that Egypt and Euro code loadings were much higher than the AASHTO loadings. Also earlier analytical studies on bridges shows that modeling of bridges using FEM is easy and it gives accurate values, some of the studies are Maher Qaqish et al. (2008) found that the results obtained from AASHTO loadings are conservative and Kanchan Sen Gupta et al.(2011) carried out the investigations on Simply supported concrete bridge deck slab for IRC vehicle loadings using finite element analysis. Reduction factors will be suggested to apply to the FEM
- 2. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 60 bending moment results to get the results similar to IRC bending moments. Critical appraisal of literature shows that most of the studies on comparison of loadings have adopted simplified method such as grillage analysis and considered only simple deck bridges which are amenable to hand computation. Since analytical modeling using FEM give a complete picture of the bridge deck response. Therefore the comparisons of the effect of different standard loadings on a set of reinforced concrete bridge decks using the finite- element method has been carried out and some FEM results are found underestimated for those modifications are needed. 2. PARAMETRIC STUDY Two types of bridge decks are considered for the analysis. i. A typical simply supported, single span, two lane slab bridge decks of span 5m, 7.5m and 9.5m with constant slab depth of 0.75m. ii. A typical simply supported, single span, two lane T beam bridge decks of span 7.5m to 20m at equal intervals of 2.5mwith constant slab depth of 0.3 m and beam dimension 0.4m x 1.6m. The width of each bridge deck is 9.5m in all cases and it includes 1m footpath on both side of carriageway. Each T beam bridge decks consist of three longitudinal T- beams and two diaphragms at ends. The geometric configuration of slab bridge deck and T beam bridge deck are indicated in Fig.1 and 2. Fig.1.Description of Deck slab bridge. Fig.2.Description of T beams bridge deck. 3. LOAD ON BRIDGE DECK MODELS In order to obtain the maximum structural response for the design, different positions of each type of loading system as per IRC 6:2000, AASHTO LRFD design specification and Euro code part 2 are analyzed. For the present study IRC class A and IRC 70R loadings are selected by seeing table 2 of IRC 6:2000, HL 93 loading from AASHTO code and Load model 1(LM1) from EURO code are considered. 4. FINITE ELEMENT MODELLING The bridge decks are analyzed using Finite element method. The 4 nodded flat plate elements are used to model the concrete slabs and the 2 nodded beam elements are used to model the concrete longitudinal beams and ends diaphragms. The mesh size of plate element is 0.2m x 0.2m.The material property of the concrete considered are the compressive strength (f ck ') = 25 Mpa, the modules of elasticity (E c ) = 25 Gpa, the Poisson's ratio (ν) = 0.2 and density = 25kN/m3 . 5. RESULTS AND DISCUSSIONS The following observations are made on the basis of the finite element analysis carried out and the results are represented in the following charts and tables. 5.1 Variation of Important Structural Response Parameters in Slab Bridge Decks under Selected Loadings (A) Deflection: It is seen from Fig.7a.thatthe maximum deflection values caused by IRC class A and IRC 70R wheeled vehicle do not differ by more than 7% for the selected aspect ratios of Slab
- 3. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 61 Bridge decks investigated. Although the total axle load is less for IRC 70R compared to class A loading, closer wheel and axle spacing counteract the effect of decreased axle load and thereby induce the almost same order of deflection. For similar cases the deflection produced by AASHTO vehicle HL 93 is varying from -7 to 17% more than that of IRC class A loading, although the total load of AASHTO vehicle exceeds 26% of IRC class A. In case of EURO standard vehicle LM1 there is a substantial increase in deflection from 1.7 to 1.8 times that of due to IRC class A against the maximum wheel load increase of 2.2. For the given class of loading the deflection has increased approximate in proportion to the cube of the span in all cases. a. Variation of deflection. b. Variation of longitudinal bending moment. Fig.7.Variation of maximum Deflection and longitudinal bending moment in Slab Bridge decks under selected loadings. (B) Longitudinal Bending Moment: It is seen from Fig.7b. that the maximum bending moment values caused by IRC class A, IRC 70R and AASHTO vehicle do not differ by more than 5% which is much less than that of deflection for the selected aspect ratios of the slab bridge decks. As bending moment is the second derivative of deflection, the change in bending moment will be a fraction of change in deflection. The order of increase in bending moment is similar to that of change in deflection. But the maximum longitudinal bending moment caused by EURO loading is more than 1.71 to 1.77 times that of due to IRC class A against the maximum wheel load increase of 2.2. (C) Transverse Bending Moment and Torsional Moment It is seen from Fig.8. that the transverse moments and torsional moments show considerable difference for different standard loads and the order of difference ranges from 26 to 46% for IRC class 70R compared to IRC class A in case of transverse moment and 26 to 85% in case of torsional moments. This is attributed to the considerable difference in wheel spacing and vehicle spacing, for example the spacing between two adjacent IRC class A loading is 1.8mwhere as the spacing between two inner wheels of typical axle of IRC class 70R load is 0.79m. However the transverse moment and torsional moment ranges from 15 to 20% and 30 to 40% respectively of corresponding longitudinal moment. Further the additional longitudinal moment computed from the torsional moment is about 50 to 55% of the value of the latter. Therefore in view of considerable width of slab and its thickness the torsional and transverse moment cannot produce any significant distortion of deck and they get further reduced more than 50% of their original value on cracking during service load stage. The AASHTO load shows a result almost similar to IRC class A in respect of transverse moment but slightly higher increase of 29 to 31% in torsional moment due to difference in wheel configuration. The EURO standard load results in enhancement in magnitude of transverse and torsional moments in the range of 1.98 to 2.10 and 1.54 to 2.02 times respectively compared to that of IRC class A loading, mainly due to the wheel configuration changes. 0 0.5 1 1.5 2 2.5 3 3.5 0 0.5 1 1.5 IRC class A loading IRC 70R loading AASHTO loading Euro loading Aspect ratio (L/B) Deflectioninmm 0 50 100 150 200 250 300 350 0 0.5 1 1.5 IRC class A loading IRC 70R loading AASHTO loading Euro loading Aspect ratio(L/B) Longitudinalbending momentinkNm
- 4. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 62 a. Variation of transverse bending moment. b. Variation of torsional moment. Fig.8.Variation of maximum Transverse moment and maximum Torsional moments in deck slab bridges under selected loadings. 4.2 Variation of Important Structural Response Parameters in T Beam Bridge Deck Slabs under Selected Loadings It is seen from Fig.10. that the effect of standard loading on T beam bridge deck slab is found to follow a pattern similar to that slab bridge decks in respect of deflection, longitudinal moment with a difference of -3 to 11% in deflection , -29 to - 82% in longitudinal bending moment and -13 to -25% in transverse bending moment in case of IRC 70R loading and with a difference of -14 to -44% in deflection, -19 to -25% in longitudinal bending moment and -23 to -37% in transverse bending moment in case of AASHTO loading. It is seen that the order of increase in maximum values of deflection, longitudinal bending moment and transverse bending moment of T beam bridge decks due to Euro standard loading is about 1.3 to 2.2 times that of IRC class A loading, which is much less than that of slab bridge deck. In case torsional moment the increase is higher for IRC 70R loading compared to the class A primarily due to closed wheel spacing in the transverse direction and in case of EURO loading torsional moment ranges from 1.6 to 3.2 times IRC class A loading. 0 20 40 60 80 100 120 0 0.5 1 1.5 IRC class A loading IRC 70R loading AASHTO loading Euro loading Aspect ratio(L/B) Transversebending momentinkNm 0 5 10 15 20 25 30 35 40 45 0 0.5 1 1.5 IRC class A loading IRC 70R loading AASHTO loading Euro loading Aspect ratio(L/B) T0rsionalmomentkNm 0 2 4 6 8 10 12 14 16 18 0 1 2 3 IRC class A loading IRC 70R loading AASHTO loading Euro loading Aspect ratio(L/B) Deflectioninmm 0 10 20 30 40 50 60 70 0 1 2 3 IRC class A loading IRC 70R loading AASHTO loading Euro loading Longitudinalbending momentinkNm Aspect ratio(L/B)
- 5. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 63 Fig.10.Variation of maximum Deflection, maximum longitudinal moment, maximum Transverse moment and maximum Torsional moments in deck slab of T beam bridges under selected loadings. 4.3 Variation of Important Structural Response Parameters in the Longitudinal Girders of T Beam Bridge Deck under Selected Loading:- The variation of maximum deflection, maximum shear force, maximum longitudinal bending moment and maximum torsional moments in the longitudinal girders of T beam bridge decks are tabulated in the following tables 1 to 4.The effect of standard loading on T beam bridge decks is found to follow a pattern similar to that slab bridge decks in respect of deflection, longitudinal moment with a difference of 17 to 37% in deflection and -10 to -27% in longitudinal bending moment in case IRC 70R loading. The corresponding differences in case of AASHTO loading are 8 to -22% in deflection and -4 to -15% in longitudinal bending moment. It is seen that the order of increase in maximum values of deflection, longitudinal bending moment and transverse bending moment of T beam bridge decks due to Euro standard loading is about 1.07 to 1.9 times that of IRC class A loading. In case of torsional moment the increase is highest for IRC 70R loading compared to the class A primarily due to closed wheel spacing in the transverse direction. The variation in torsional moment is much less compared to a slab deck because the presence of girders in both direction and also reduce the distortion and warping caused by torsion. The maximum shear force in beams mainly depends on the magnitude of loading, since wheel load of AASHTO loading, Euro loading is more compared to IRC class A, the maximum shear force values produced by AASHTO loading, Euro loading increased by -71 to 52% and 0.5 to 1.8 times respectively compared to that of IRC class A loading. Although the IRC class 70R wheel load is small compared to IRC class A wheel load due to the closed wheel spacing the maximum shear force values decreased by -1 to 91%. 0 10 20 30 40 50 60 0 1 2 3 IRC class A loading IRC 70R loading AASHTO loading Euro loading Transversebending momentinkNm Aspect ratio(L/B) 0 5 10 15 20 25 30 0 1 2 3 IRC class A loading IRC 70R loading AASHTO loading Euro loading Aspect ratio(L/B) TorsionalmomentinkNm
- 6. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 64 Table.1. Variation of Deflection in longitudinal girders Table.2. Variation of Shear force in longitudinal girders Aspec t ratio (L/B) Shear force in beam 1 in kN Shear force in beam 2 in kN Shear force in beam 3 in kN IRC class A loading IRC 70R loading AASHT O loading Euro loading IRC class A loading IRC 70R loading AASHT O loading Euro loading IRC class A loading IRC 70R loadin g AASHT O loading Euro loading 0.789 121.83 8 94.266 115.712 329.13 5 123.67 9 150.81 2 112.027 293.74 7 48.191 4.611 71.333 82.902 1.053 107.10 6 129.42 1 140.832 368.98 5 139.59 7 183.08 9 141.789 330.55 1 59.694 14.844 92.389 103.60 9 1.316 146.50 2 167.38 2 162.393 401.3 148.76 187.02 2 165.473 356.95 68.497 30.78 112.691 123.04 5 1.579 153.42 4 196.13 5 180.23 430.22 5 154.78 6 229.52 2 183.004 379.40 9 75.37 48.028 129.336 142.03 2 1.842 166.69 4 221.04 4 195.759 457.36 5 168.56 228.15 7 197.896 399.51 1 104.17 8 64.442 143.938 160.95 2.105 183.97 4 238.93 209.758 482.33 185.25 9 256.69 8 210.86 418.15 7 118.74 1 80.034 156.747 179.66 2 Table.3. Variation of Longitudinal bending moments in longitudinal girders Aspec t ratio (L/B) Bending moment in beam 1 in kNm Bending moment in beam 2 in kNm Bending moment in beam 3 in kNm IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g IRC class A loading IRC 70R loadin g AASHT O loading Euro loadin g 0.789 269.87 241.21 222.69 787.6 292.89 324.44 246.99 748.36 133.09 25.97 159.80 243.09 Aspec t ratio (L/B) Deflection in beam 1 in mm Deflection in beam 2 in mm Deflection in beam 3 in mm IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loading 0.789 0.252 0.237 0.221 0.744 0.273 0.321 0.249 0.701 0.124 0.026 0.16 0.231 1.053 0.614 0.697 0.643 1.793 0.628 0.83 0.7 1.596 0.325 0.138 0.478 0.629 1.316 1.34 1.666 1.41 3.588 1.293 1.771 1.469 3.046 0.755 0.469 1.076 1.415 1.579 2.492 3.228 2.695 6.354 2.263 3.113 2.706 5.233 1.496 1.138 2.112 2.784 1.842 4.276 5.455 4.594 10.309 3.68 4.962 4.498 8.371 2.705 2.253 3.686 4.953 2.105 6.862 8.555 7.241 15.704 6.116 7.496 6.979 12.706 4.568 3.989 5.94 8.169
- 7. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 65 1.053 398.93 414.63 376.65 1152.9 412.69 502.45 408.59 1043.3 207.35 81.19 278.66 395.38 1.316 567.53 660.40 560.5 1538.3 555.30 703.2 582.43 1334.7 314.22 181.83 425.25 587.18 1.579 740.92 907.01 759.72 1937.2 697.97 882.12 762.67 1634.8 434.71 313.39 591.96 814.7 1.842 937.49 1149.4 968.94 2345.6 860.91 1051.8 949.3 1952.5 580.65 462.56 772.57 1075 2.105 1139.7 1399.5 1185.24 2761.5 1031.7 1237.1 1145.1 2290 738.29 633.36 965.59 1364.8 Table.4. Variation of Torsional moments in longitudinal girders Aspe ct ratio( L/B) Torsional moment in beam 1 in kNm Torsional moment in beam 2 in kNm Torsional moment in beam 3 in kNm IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g IRC class A loadin g IRC 70R loadin g AASHT O loading Euro loadin g 0.789 15.5 35.5 4.7 32.4 2.45 24.9 3.977 37.24 20.8 6.69 20.32 35.17 1.053 14.6 42 6.25 31.78 3.45 29.3 3.361 43.28 25 18.4 25.18 45.3 1.316 15.2 44.7 6.46 32.93 6.61 38 3.54 50.3 28.2 34.1 29.61 56.07 1.579 15.9 41.4 5.75 38.7 10.6 46.5 5.59 57.8 30.4 48.6 32.8 67.8 1.842 16.9 35.6 6.12 46.2 15.1 53.7 8.31 66.1 35.7 58.7 35.14 81 2.105 22.6 32.3 6.492 56.9 19.8 64.2 11.07 76.6 40.7 74.9 37.37 94.8 4.4 Comparison of important structural response parameters in selected slab bridge deck and T beam bridge deck slab of aspect ratio 0.789 under selected loading:- The comparison of important structural parameters in slab bridge deck and T beam bridge deck slab of aspect ratio 0.789 is shown in the Table.9. The maximum deflection in T beam bridge deck slab is reduced by 25 to 30 % in case of IRC class A, AASHTO and EURO loading compared to slab bridge deck but in case of IRC 70R loading maximum deflection increases by 1.95% because of less wheel spacing. In case of longitudinal bending moment in T beam bridge deck slab is decreased by 76 to 81% compared to slab bridge deck for all selected loading cases. Similarly the transverse bending moment and tosional moment in T beam bridge deck slab is reduced by 33 to 65% compared to slab bridge deck for all selected loading cases. This reduction in important structural parameters in T beam bridge deck slab compared to slab bridge deck is due to the provision beams in both direction of slab. Table.5. Comparison of important structural response parameters in selected slab bridge deck and T beam bridge deck slab of aspect ratio 0.789 under selected loading Loading IRC class A Loading IRC 70R Loading AASHTO Loading EURO Loading Bridge deck type Slab deck T beam deck Slab deck T beam deck Slab deck T beam deck Slab deck T beam deck Deflection in mm 0.533 0.361 0.513 0.523 0.483 0.319 1.493 1.105 Longitudinal bending moment in kNm 91.94 16.874 91.472 21.788 87.114 20.199 254.868 53.372 Transverse bending moment in kNm 30.987 14.913 43.725 17.032 30.447 20.465 94.962 38.392 Torsion in kNm 12.268 5.572 19.491 6.933 9.164 5.242 34.693 22.989
- 8. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308 __________________________________________________________________________________________ IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 66 CONCLUSIONS a. The maximum values of deflection and longitudinal bending moment caused by IRC class A and 70R wheeled vehicle do not differ by more than 7% for the selected aspect ratios of Slab Bridge decks investigated.The corresponding difference in case of T beam decks is -22 to 37%. b. AASHTO loading causes -7 to 17% higher deflection and less than 5% in case of longitudinal bending moment compared to IRC class A loading. While the corresponding range is 1.7 to 1.8 times for EURO loading. c. In general maximum transverse and maximum torsional moments are more pronounced in case of slab bridge decks compared to T beam decks and are found to be in the range of 15 to 20% and 30 to 40% respectively of corresponding longitudinal moment in case slab bridge decks and less than 5% of corresponding longitudinal moment in case of T beam decks because of higher transverse moment of inertia and torsional rigidity. d. Because of their lower magnitude and thick solid sections are adopted for the members the maximum torsional moment and maximum transverse bending moments may not have any major significance on the design of slab bridge deck and T beam bridge deck. e. The provision of T beam bridge decks instead of solid bridge decks of same aspect ratio is found to reduce in maximum deflection values by 25 to 30% and the maximum longitudinal bending moment values are reduced by 76 to 81%. Another major advantage is the reduction in maximum torsional and maximum transverse moments by 33 to 65%. f. The study shows that there is a wide variation in the highway bridge loading standards of different countries. However the changes in critical response parameters are not very significant. IRC has adopted 6 standard loadings with widely varying magnitude of wheel loading and wheel and axle spacing. However the investigations indicate that there is no appreciable difference in structural response parameters for the different loadings. It is suggested that IRC may also adopt the single design vehicle with simple configuration for standard loading similar to AASHTO and EURO standard loading which have only 2 to 3 axles. REFERENCES [1] P.K. Thomas “A Comparative Study of Highway Bridge Loadings in Different Countries”supplementary report 135UC, Transport and road research laboratory. [2] Medhat Kamal Abdullah “Comparison between Highway Codes for Traffic Loads on Bridges”Life Science Journal 2013: PP.621-627. [3] Dr.MaherQaqish, Dr.EyadFaddaand Dr.EmadAkawwi“Design of T-beam Bridge by Finite Element Method and AASHTO Specification”KMITL Sci. Journal. Vol.8 No.1 January – June, 2008. [4] KanchanSen Gupta and SomnathKarmakar“Investigations on Simply supported concrete bridge deck slab for IRC vehicle loadings using finite element analysis”Journal of Earth Sciences and Engineering, Volume 04, No 06 SPL, October 2011, PP. 716-719. [5] IRC 6:2000 “Standard Specifications and Code of Practice for Road Bridges, Section-II Loads and Stresses”, Indian Road Congress, New Delhi. [6] American Association of State and Highway Transportation Officials (AASHTO) specifications. [7] Eurocode 1 Part 2 - prEN 1991-2-2002. [8] IRC 21:2000 “Standard Specifications and Code of Practice for Road Bridges, Section-III Cement Concrete (Plain and Reinforced)”,Indian Road Congress, New Delhi.