Analysis of rc frame with and without masonry infill wall with different stiffness with outer central opening

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 06| Jun-2014, Available @ http://www.ijret.org 76
ANALYSIS OF RC FRAME WITH AND WITHOUT MASONRY INFILL
WALL WITH DIFFERENT STIFFNESS WITH OUTER CENTRAL
OPENING
Mohammad H. Jinya1
, V. R. Patel2
1
P.G. Student, Applied Mechanics Department, M. S. University of Baroda, Vadodara, India.
2
Assistant Professor, Applied Mechanics Department, M. S. University of Baroda, Vadodara, India.
Abstract
In reinforced concrete frame building, masonry wall are generally used in as infills and specified by architects as partitions in
such a way that they do not contribute to the vertical gravity load-bearing capacity of the structure. Infill walls protect the inside
of the buildings from the environment hazards and create separation insides. In addition to this infills have a considerable
strength and stiffness and they have significant effect on the seismic response of the structural systems. Mostly two common
structural damages observed caused by masonry infill walls in earthquakes i.e soft stories and short columns. In office or
residential building outer side central opening are used. In this case central opening are provided in periphery wall with different
percentage i.e. 15% and 25% and brick compressive strength are used as per IS : 1905-1987 i.e. 5.0 and 12.5 N/mm2
and Brick
Masonry strength is 0.50 and 1.06N/mm2
. In ETABS software G+9 R.C.C framed building models has been prepared, Seismic
coefficient method(SCM) and time-history(TH) has been performed for analysis as per IS 1893:2002. Story displacement, base
shear, story drift, axial force with and without soft story considering effect of infill walls with different percentage of opening are
the parameters considered in this study. For Macro model, Equivalent diagonal strut (EDS) method is used to find out width of
strut using FEMA approach method. The results of bare frame, soft story and infill wall panel are discussed and conclusions are
made in this studies.
Key Words: Base shear, Displacement, Equivalent Diagonal Strut, Storey Drift, Soft storey.
--------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
In RC frame brick walls is just architectural point of view
and to make partition and other aspect. In multistory
buildings, the ordinarily occurring vertical loads i.e. dead or
alive, do not cause much of a effects, but the lateral loads
due to wind or earthquake tremors are a matter of great
concern and need special consideration in the design of
buildings. These lateral forces can produce the critical stress
in a structure, set up undesirable vibrations, and in addition,
cause lateral sway of the structure which can reach a stage
of discomfort to the occupants. In many countries situated in
seismic regions, reinforced concrete frames are infilled fully
or partially by brick masonry panels with or without
openings. Although the infill panels significantly enhance
both the stiffness and strength of the frame, their
contribution is often not taken into account because of the
lack of knowledge of the composite behavior of the frame
and the infill. During the elastic response phase, the
presence of brick infill walls increases in plane lateral
stiffness of the structure and reduced its fundamental
period, and as a result leads to larger shear forces.
In residential building RC frame structure are infill by brick
panels on all four sides and resisting the lateral earthquake
loads on building. By experimentally it has been shown that
brick walls have high initial lateral stiffness (Moghaddam
and Dowling 1987, Drysdale et al. 1999, Paulay and
Priestley 1992,). Hence masonry infills in RC frames
different lateral load transfer mechanism of the structure
from predominant frame action to predominant truss action
(Murty and Jain 2000). Shown in Figure 1 below. Thus it is
responsible for increase in axial forces in the RC frame.
Fig -1: Change in lateral-load transfer mechanism due to masonry infill
(Murty and Jain 2000)

_______________________________________________________________________________________
2. LITERATURE REVIEW
From several research paper studies it shows that Equivalent
diagonal strut method is used for modeling the brick infill
wall to easy represent the effect of inplane during lateral
load and its equations for Equivalent diagonal strut width for
full infill given by various researchers are,
In 1961 Holmes,
w = dz/3 where, dz = Diagonal length of
infill panel
In 1962 Equivalent diagonal strut according to Smith,
here
and
In 1969 Smith and Carter,
where
In 1971 Mainstone,
w = 0.175dz (λhH’)-0.4
In 1984 Liaw and Kwan,
w = (0.95Hcosθ)/ √λhH’
In 1992 Paulay & Priestley,
w = dz/4
3. RESEARCH OBJECTIVES
The main objective of this paper is to simplify the analysis
concept of the building industry. And also carry out the
effect of brick masonry infilled walls for the static linear
analysis and Time history analysis of the R.C.C high rise
building with single diagonal strut approach as per IS
1893:2002 and IS 456:2000. The result would be carried out
and compare for G+9 story R.C.C. building.
4. METHOD OF ANALYSIS OF THE BRICK
INFILL WALL
4.1 Data Taken
Table -1: Data for Building
4.2 Types of Model
Table -2: Types of Model
ID
(The First value
indicates masonry
comp. stress,
N/mm2
)
Description
0.5BFGSS15%
Bare frame ground soft story with
15% outer central opening
0.5SFGSS15%
Strut frame ground soft story with
1.06BFGSS15%
1.06SFGSS15%
0.5BFGSS25%
0.5SFGSS25%
1.06BFGSS25%
Story = G+8 4x3 bay
Ground floor height = 3.0m
Typ. story height= 2.9m
Basement height= 3.0m
Beam= 230 x 450 mm
Column= 500 x 500mm
Spacing of frame X direction= 3m
Spacing of frame Y direction= 3m
Live load= 1.5 kn/m2
for terrace
3.0 kn/m2
for typ floor
Dead load= 2.0 kn/m2
for terrace
1.0 kn/m2
for typ floor
Response Reduction Factor, R= 3 for SMRF
Importance factor, I= 1.0
Type of soil= Medium
Damping of structure= 5%
Grade of concrete= M30
Steel= Fe 415
Density of concrete= 25 kn/m3
Density of brick wall= 20 kn/m3
Modulus of elasticity of
concrete, Ec=
27.386 x 106
kn/m2
Modulus of elasticity masonry,
Em=
1)0.275 x 106
kn/m2
2)0.583 x 106
kn/m2
Thick. of outer Brick wall= 115 mm
Thick. of inner Brick wall= 115 mm
Thick. of slab= 125mm
Poisson ratio of concrete= 0.2
Poisson ratio of brick wall= 0.17
Seismic zone= V
Z = 0.36
Time history Bhuj_Ahmedabad

_______________________________________________________________________________________
1.06SFGSS25%
0.5BFWSS15%
Bare frame without soft story with
0.5SFWSS15%
Strut frame without soft story
with 15% outer central opening
1.06BFWSS15%
1.06SFWSS15%
0.5BFWSS25%
0.5SFWSS25%
1.06BFWSS25%
Bare frame without soft story
1.06SFWSS25%
4.3 Modelling of Brick Infill Wall
Fig -2: Plan
4.4 FEMA Approach
Equivalent diagonal strut method is used for modeling the
brick infill wall according to FEMA273.The infill frame in
this model was assumed as an equivalent diagonal strut
with frame the pin joint(hinge joint) at the corners of the RC
frame(See Fig.5).
In this method the brick infill wall replaced by diagonal
strut. The frame is analyzed as truss element.
The equivalent diagonal strut width is given as:
w = 0.175(λ1hcol
)-0.4
rinf………………eqn
1
Where, λ1 =
Fig- 5 Diagonal strut with pinned joint
And
hcol =Column height between centerlines of beams,m
hinf = Height of infill panel, m
Efe =Expected modulus of elasticity of frame
material,kn/m2
Eme =Expected modulus of elasticity of infill material,
kn/m2
Icol = Moment of inertia of column, m4
Linf = Length of infill panel, m
rinf = Diagonal length of infill panel, m
tinf =Thickness of infill panel and equivalent strut, m
θ =Angle whose tangent is the infill height-to-length
aspect ratio, radians
λ1 = Coefficient used to determine equivalent width of
infill strut
BEA
M
COLUMN
EDS
Hinge
Fig- 3 3D View
of Bare Frame
Fig- 4 3D View
of Strut Frame
BEAM
COLUMN

_______________________________________________________________________________________
4.5 Strut Reduction Factor
Reduction factor
λ=1-2αw
0.54
+αw
1.14
The above coefficient (ʎ) could be used to find the
equivalent width of a strut for the case of an infill with
opening by multiplying the results of Eqns. 1 above for
central opening.
4.6 Modulus of elasticity of brick masonry
In lieu of prism tests, values for the modulus of elasticity of
masonry in compression shall be taken as, 550 times the
expected masonry compressive strength, fme.
i) Compressive strength, fme = 0.5MPa
(IS 1905:1998, Table-8)
Em= 550 x fme = 550 x 0.5 x 103
= 0.275 x 106
kn/m2
ii) Compressive strength, fme = 1.06MPa
(IS 1905:1998, Table-8)
Em= 550 x fme = 550 x 1.06 x 103
= 0.583 x 106
kn/m2
4.7 Fundamental Natural Period of Vibration, (Ts)
Ts= 0.09h/sqrt(d)
Tx = 0.8314 s, Ty = 0.96 s
Where, h = Height of building, in m
d = Base dimension of the building at the plinth level, in m
4.8 Average Response Acceleration Coefficient
(Sa/g)x = 1.36/T = 1.635826
(Sa/g)y = 1.36/T = 1.416667
5. RESULT AND DISCUSSION
5.1 Base Shear
The design base shear Vb as per IS: 1893 shall be calculated
by following formula,
Vb = Ah x W
Where, Ahx,y = ZIS/2RG
Ahx = 0.069949
Ahy = 0.049461
Table -3: Base shear
BASE SHEAR IN X-DIRECTION(KN)
ID SCM TH
0.5BFGSS15% 1549.31 1222.84
0.5SFGSS15% 1549.31 1178.59
1.06BFGSS15% 1549.31 1222.84
1.06SFGSS15% 1549.31 1379.87
0.5BFGSS25% 1519.63 1196.86
0.5SFGSS25% 1519.63 1155.00
1.06BFGSS25% 1519.63 1196.86
1.06SFGSS25% 1519.63 1348.81
0.5BFWSS15% 1595.76 1233.61
0.5SFWSS15% 1595.77 1202.23
1.06BFWSS15% 1595.76 1233.61
1.06SFWSS15% 1595.77 1693.92
0.5BFWSS25% 1566.01 1208.23
0.5SFWSS25% 1566.01 1186.65
1.06BFWSS25% 1566.01 1208.23
1.06SFWSS25% 1566.01 1652.86
Chart -1: Base shear at base in X Direction (Kn)
We can conclude from this analysis that with increase in
stiffness of infill wall base shear of building also increase
thus stiffness of wall is should be minimum.
5.2 Displacement
0
0.2
0.4
0.6
0.8
1
1.2
0 50 100 150
Reductionfactorλ
Opening %
0
500
1000
1500
2000
0.5BFGSS15%
0.5SFGSS15%
1.06BFGSS15%
1.06SFGSS15%
0.5BFGSS25%
0.5SFGSS25%
1.06BFGSS25%
1.06SFGSS25%
0.5BFWSS15%
0.5SFWSS15%
1.06BFWSS15%
1.06SFWSS15%
0.5BFWSS25%
0.5SFWSS25%
1.06BFWSS25%
1.06SFWSS25%
BASE SHEAR IN X-DIR.
SCM TH

_______________________________________________________________________________________
Table -4: Displacement at the top level
DISPLACEMENT AT ROOF LEVEL IN MM
SR
NO.
ID SCM TH
1 0.5BFGSS15% 51.2 31.55
2 0.5SFGSS15% 44.59 27.37
3 1.06BFGSS15% 51.2 31.55
4 1.06SFGSS15% 39.42 31.21
5 0.5BFGSS25% 50.28 31.45
6 0.5SFGSS25% 44.34 27.64
7 1.06BFGSS25% 50.28 31.45
8 1.06SFGSS25% 39.56 31.19
9 0.5BFWSS15% 52.7 31.69
10 0.5SFWSS15% 44.74 28.95
11 1.06BFWSS15% 52.7 31.69
12 1.06SFWSS15% 38.63 32.58
13 0.5BFWSS25% 51.78 31.6
14 0.5SFWSS25% 44.52 29.19
15 1.06BFWSS25% 51.78 31.6
16 1.06SFWSS25% 38.81 32.61
Chart -2: Displacement at the top in X Direction
The displacement in X direction for diff. models are shown
in Graph 2. From graph it can be concluded that with
increase in stiffness of infill wall displacement of building
decreased by 12% to 25 %( see Table 4) in Static and
Dynamic analysis.
5.3 Story Drift
The drift value for SCM and TH analysis results are shown
in followings different chart in mm (see Chart 3 to 6).
Chart-3: Story Drift for SCM in X direction (0.5)
Chart-4: Story Drift for SCM in X direction (1.06)
0
10
20
30
40
50
60
0.5BFGSS15%
0.5SFGSS15%
1.06BFGSS15%
1.06SFGSS15%
0.5BFGSS25%
0.5SFGSS25%
1.06BFGSS25%
1.06SFGSS25%
0.5BFWSS15%
0.5SFWSS15%
1.06BFWSS15%
1.06SFWSS15%
0.5BFWSS25%
0.5SFWSS25%
1.06BFWSS25%
1.06SFWSS25%
DISPLACEMENT IN MM X-DIR.
SCM TH
0
1
2
3
4
5
6
7
8
9
10
0 2 4 6 8
STORYNO.
DRIFT IN MM
SCM-STORY DRIFT FOR 0.5N/MM 2
0.5BFGSS15% 0.5BFGSS25%
0.5BFWSS15% 0.5BFWSS25%
0.5SFGSS15% 0.5SFGSS25%
0.5SFWSS15% 0.5SFWSS25%
0
1
2
3
4
5
6
7
8
9
10
0 2 4 6 8
STORYNO.
DRIFT
SCM-STORY DRIFT FOR 1.06 N/MM 2

_______________________________________________________________________________________
Chart-5: Story Drift for TH in X direction (0.5)
Chart-6: Story Drift for TH in X direction (1.06)
The drift value has a particular importance of serviceability
requirement. According to Indian seismic code IS 1893 Part-
1 :2002, The story drift in any story due to the minimum
specified design lateral force, with partial load factor of 1.0,
shall not exceed 0.004 * h, where h = story height.
In building with strut, Story drift is less as compared to
without considering strut type building in both direction, i.e.
and Y.(See Chart 3 to 6). All story drift are found to be
within permissible limit i.e. 1.2 cm.
5.4 Axial Force
The maximum axial force in the column are as shown in
following,
Table 5: Maximum Axial Force (kn) on column at Base in
EQ-X
0.5BFGSS15% & 1.06BFGSS15% 0.5BFGSS25% & 1.06BFGSS25%
0.5SFGSS15%
1.06SFGSS15%
0
1
2
3
4
5
6
7
8
9
10
0 1 2 3 4 5
STORYNO.
DRIFT IN MM
TH-STORY DRIFT FOR 0.5N/MM 2
0
1
2
3
4
5
6
7
8
9
10
0 1 2 3 4 5
STORYNO.
DRIFT
TH-STORY DRIFT FOR 1.06 N/MM 2

_______________________________________________________________________________________
0.5BFWSS15% & 1.06BFWSS15% 0.5BFWSS25% & 1.06BFWSS25
From the analysis we can conclude that for the models with
Strut Frame has quite higher axial force on the ground
column as compared to Bare Frame. And it’s depending on
infill stiffness. The values are given in Table.5 for X
direction only in EQ-X.
6. CONCLUSION
In this paper sixteen models are prepared for Static Linear
analysis and Dynamic analysis (TH) results of models i.e.
without strut and with strut of infill wall with central outer
opening with 15% and 25% are compared. From this
analysis it can be concluded that diagonal strut will change
the seismic performance of RC building. Axial force in
column increased, story displacement and story drift are
decreased and base shear is increase with higher stiffness of
infill. If in the ground level at least periphery wall is provide
then soft story effect can be minimized. It can also be
concluded, the increase in the percentage of opening leads to
a decrease in the lateral stiffness.
7. ACKNOWLEDGEMNET
The author gratefully acknowledge the encouragement and
support given by the MS University of Baroda.
8. REFERENCES
[1] P. G. Asteris, 2003, M.ASCE, Lateral Stiffness of
Brick Masonry In filled Plane Frames, Journal of
Structural Engineering, Vol.129, No.8, August1,
2003.ASCE, ISSN0733-9445/2003/8-1071±1079.
[2] Panagiotis G. Asteris, Christis Z. Chrysostomou,
Ioannis P. Giannopoulos, and Eleni Smyrou,
Masonry Infilled Reinforced Concrete Frames With
Openings, III ECCOMAS Thematic Conference on
Computational Methods in Structural Dynamics and
Earthquake Engineering, M. Papadrakakis, M.
Fragiadakis, V. Plevris (eds.) ,Corfu, Greece, 26–28
May 2011
[3] Nehrp Guidelines for the Seismic Rehabilitation of
Buildings, FEDERAL EMERGENCY
MANAGEMENT AGENCY, FEMA 273 / October
1997, Chap. 7.
[4] Hemant B. Kaushik, Durgesh C. Rai, M.EERI, and
Sudhir K. Jain, M.EERI, Code Approaches to
Seismic Design of Masonry-Infilled Reinforced
Concrete Frames: AState-of-the-ArtReview,
Earthquake Spectra, Volume22, No.4, pages 961-
983, November2006; 2006, Earthquake Engineering
Research Institute.
[5] Diptesh Das and C.V.R. Murty, Brick masonry infills
in seismic design of RC framed building, The Indian
Concrete Journal,July 2004.

_______________________________________________________________________________________
[6] Mohd Danish, Shoeb Masood, Zaid Mohammad, 2nd
International Conference on Emerging Trends in
Engineering & Technology, April 12-13, 2013.
[7] BIS, IS1905:1998 Code of practice structural use of
unreinforced masonry.
[8] I.S. 1905-1987, Code Of Practice For Structural Use
Of Unreinforced Masonry, Bureau of Indian
Standards, New Delhi
[9] Indian standard, Code of Practice for Plain and
Reinforced Concrete, IS 456: 2000, Bureau of Indian
Standards, New Delhi, India.
[10] Indian Standard, Criteria for earthquake resistant
design of structures, IS 1893(Part 1): 2002, Bureau of
Indian Standards, New Delhi, India.
[11] Murty, C.V.R., and Jain, S.K., 2000. Beneficial
influence of masonry infills on seismic performance
of RC frame buildings, Proceedings, 12th
World
Conference on Earthquake Engineering, New
Zealand, Paper No.1790.
BIOGRAPHIES
Jinyawala Mohammad Husenibhai
is a ME Dissertation student doing
his thesis under the guidance of
Dr.V. R. Patel from The M. S.
University of Baroda. He has done
his B.E. in civil engineering from
the Indore, RGPV Bhopal
university.
Dr. V. R. Patel is an assistant
professor in the Faculty of
Technology and Engineering, The
M. S. University of Baroda. He has
a broad experience in the field of
structure engineering. He has also
designed more than 2500 projects
which includes industrial, High rise
building.

Analysis of rc frame with and without masonry infill wall with different stiffness with outer central opening

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Analysis of rc frame with and without masonry infill wall with different stiffness with outer central opening (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

Analysis of rc frame with and without masonry infill wall with different stiffness with outer central opening