Api 653 study guide

API 653 Certification Prep
API 575 Study Questions
This following is a study aid that you can use to help you learn the details and content of API
RP-575, Inspection of Atmospheric and Low-Pressure Storage Tanks. There will be about
15-30 questions from this document on the API 653 exam. We do not spend much time in
class discussing this publication. So it is important that you become familiar with this content
in your personal study sessions.
The questions in this study aid are in the same order as API 575. An answer key will be
provided in class. Its helpful to read through API 575 before working on this exercise!
Section 2
1. What old code was used to build rivet tanks? _______________
2. What code covers the safety precautions of entering a tank? _______________
3. What code covers cathodic protection of tanks? _______________
4. What code covers tank linings? _______________
5. What code covers tank venting? _______________
6. What code covers design of low-pressure tanks? _______________
8/19/03 1 Copyright MSTS

Section 3
1. When taking UT thickness readings, it is recommended to use a digital meter that also
has a _____________ _________________.
2. Dual-element transducers on a digital UT meter can effectively measure thickness
between: _______________________ inch.
3. A dual-element transducer may give a false reading when the material thickness is less
than _________________ inch.
4. Which type of UT transducer is best for small diameter deep pits?
a. Single element transducers
b. Dual element transducers
c. Large diameter transducers
d. Transducers made with pure quartz
5. How does paint or a coating affect a UT thickness reading?
a. _______________________________________________________________
b. _______________________________________________________________
6. For coated tanks that have coatings that vary in thickness, which type of UT
transducer is best?
a. Single element transducers
b. Dual element transducers
c. Large diameter transducers
d. Transducers made with pure quartz
7. When performing a UT scan, the scans should overlap by _________ of the transducer
diameter.
8. When performing a UT scan, a large diameter transducer may miss _______________
diameter deep pits.
9. UT shear-wave is primarily used in tanks to find defects in ________________ joints.

10. List four primary advantages of using the magnet-flux floor scanner.
a. ___________________________________
b. ___________________________________
c. ___________________________________
d. ___________________________________
11. When using a magnet-flux scanner to inspect a tank floor, indications found are
generally "proved-up" using ____________.

Section 4
1. When the product temperature in a tank increases, the vapor pressure of the product
_________________.
2. While in operation, which tank type roof is supported by internal members?
a. Cone roof
b. Dome roof
c. Floating roof
d. Umbrella
3. What is the primary reason(s) for using a floating roof? _______________________
_______________________________________________________________
4. Which type of external floating-roof is the most susceptible to sinking?
_____________________________
5. Which type of external floating-roof is the least susceptible to sinking?
_____________________________
6. The most common type of floating-roof seal is the ______________________
____________________.
7. When are internal floating roof tanks used? ________________________________
_____________________________________
8. Low-pressure storage tanks are those with a design pressure from _______ psig to
_______ psig.
9. Low-pressure storage tanks are normally used for products that have a high
_______________ pressure.
10. For pressures above _________ psig, the hemispheroidal, spheroidal, and noded
spheroidal tanks are commonly used.

Section 5
1. Tank pads with cinders that contain ________________ compounds become corrosive
when wet.
2. List 3 items in a sand pad that may cause bottom-side corrosion.
a. ___________________________
b. ___________________________
c. ___________________________
3. List two causes of severe external corrosion at the bottom of the lower shell course.
a. ___________________________________
b. ___________________________________
4. Small depressions in the roof are susceptible to _____________ corrosion.
5. Concentration cell corrosion may occur in the many niches of ________________
tanks.
6. What metallurgy is primarily used when constructing crude oil tanks?
______________________________
7. What are three common vapors that cause corrosion in a tank s vapor space?
a. ______________________________
b. ______________________________
c. ______________________________
8. Generally in the liquid portion of a tank, internal corrosion is worse at the:
a. bottom of the tank.
b. top of the liquid.
c. welds.
Why? _____________________________________________

9. What type of tank failure results in a sudden loss of the product?
________________________________
10. Cracks are most susceptible in _____________ and between ___________ holes.
11. What weld is most susceptible to cracking in a hot tank?
______________________________
12. What weld is most susceptible to cracking in a large diameter tank?
______________________________
13. What is the most likely problem when there is excessive uniform tank settlement?
______________________________
14. What is a common problem with pressure-vacuum vents?
_____________________________________________________
15. A plugged floating roof drain can cause the roof to ______________.
16. The inspection checklists listed in Appendix C are:
a. mandatory for all tanks.
b. mandatory only on low-pressure storage tanks.
c. considered a "memory jogger" for the inspector.

Section 6
1. After a significant rainfall the _________________ on floating roofs should be
checked.
Section 7.1 - 7.3
1. Once the tank atmosphere is safe to enter and there is permit that allows entry, prior to
entering the tank it is important to check the condition of _______________
components to make sure that they won t ________________.
2. Prior to conducting an external or internal inspection the inspector should review prior
inspection _______________.
3. What type of corrosion can happen between a bolt head and a steel plate?
_____________________________
4. When inspecting handrails pay particular attention to tubular members. Why?
__________________________________
5. Low spots on platforms that collect water are routine places for corrosion to occur.
This can be solved by _____________________________.
6. List the 4 types of tank foundations.
a. ___________________________________
b. ___________________________________
c. ___________________________________
d. ___________________________________
7. For tanks on a concrete pad, the floor to pad joint should be _____________.

8. Corrosion below an anchor-bolt nut sometimes can be detected by ________________
testing.
9. Pipe connected to tanks should be inspected. Where pipe enters soil, the soil should
be dug away _____________ inches to inspect for soil-to-air corrosion?
10. If distortion is found at the nozzles, the welds and shell area should be examined for
_________________.
11. Grounding connections should be _________________ checked.
12. The resistance of the grounding connections should not exceed ________ ohms.
13. Which potential problem with coatings is most difficult to see? _________________
14. Paint blisters occur most often on the ___________ and on the shell area that receives
the most _________________.
15. The _______________ side of an insulated tank is most susceptible to CUI.
16. CUI may be significant at the bottom of the tank. Why? ____________________
________________________
17. Inspectors should not walk on ___________________ tanks roofs.
18. The depth of a locally corroded area can best be measured with a long _____________
_________________.
19. The depths of isolated pits are normally measured with a ________ _____________.
20. What part of the shell of a floating roof tank usually corrodes at twice the rate of the
rest of the shell? ____________________________
21. Stiffeners and wind girders are normally inspected visually and by ______________
testing.

22. Caustic tanks may be subject to a corrosion mechanism called ________________
__________________.
23. Where is caustic cracking most common? ______________________________
24. Caustic material seeping through cracks will usually form ________________
deposits.
25. Prior to welding on a tank in caustic service the area should be thoroughly cleaned and
checked with an _____________________ solution.
26. Hydrogen blistering may be found on the shell near:
a. bottom
b. nozzles
c. top of the tank
d. weld seams
27. Hydrogen blisters can be found using:
a. _____________________________________
b. _____________________________________
c. _____________________________________
28. Tank shell distortions can be measured using a ___________________________.
29. List 3 causes of tank shell distortion.
a. ______________________________
b. ______________________________
c. ______________________________
30. Tank shell distortions may cause welds to be highly _________________ and result in
a ___________________.
31. Rivets can be best checked for looseness by using a __________________.

32. The thickness of a tank roof can be checked by ____________________________ or
__________________.
33. When walking on a cone-roof tank, planks can be used. Planks that are used should be
long enough to span ________________________________.
34. Individuals on a tank roof should walk on the _________ __________.
Why? _________________________
35. When walking on a floating roof, the tank should always be in the ______________
____________ position.
36. Before allowing individuals on a floating roof tank that is not in the high-gauge
position, a ______________ test shall be performed before personnel are allowed on
the roof.
37. External corrosion on a tank roof will usually be most severe at ________________
__________________________________.
38. What is the primary reason for periodically inspecting flame arrestors?
_________________________
39. When tunneling under a tank to inspect the bottom (it is rarely done!) it is difficult to
properly _______________ the tunnel.
40. Probably the most expensive way to inspect the bottom-side of the tank floor is to
____________ the tank.
41. List the 3 types of floating roof drains
a. ____________________________________________
b. ____________________________________________
c. ____________________________________________

42. When the tank is out-of-service, the floating roof drain piping can be checked by
pressure testing. Drains with swing joints require testing at two pressures.
a. 1st pressure: ______ psig, checks the _________________
b. 2nd
pressure: ______ psig, checks the __________________
43. During the external inspection, float-type gauges should be checked to make sure they
are not cracked or filled with _______________.

Section 7.4 - 7.7
1. Normally internal tank corrosion is most prevalent in:
a. _________________________________________
b. _________________________________________
c. _________________________________________
2. Dry pyrophoric material can cause:
a. cracking.
b. general metal loss.
c. ignition.
d. pitting,
3. Pyrophoric material may accumulate on the tank bottom or on the top of the
__________________.
4. In sour services, corrosion is often occurs in the __________________.
5. In sour services, corrosive vapors are formed when the _________________________
mixes with moisture and air.
6. Carbon steel that has slag inclusions and ________________________ is more
susceptible to hydrogen blistering.
7. Caustic stress corrosion cracking is prevalent in carbon steel when the temperature is
above _________ o
F.
8. Tank bottoms are normally inspected visually and with one of the following:
a. ______________________________________
b. ______________________________________
c. ______________________________________

9. During the internal inspection, a tank floor can be 100% inspected or partially
inspected when using a statistical method. Based on the statistical method answer the
following:
a. What percentage of the floor should be scanned? ____________%
b. What pattern across the tank is generally used? _____________
c. What part should be completely scanned? _________________________
10. Corrosion on the tank bottom may be very _________________.
11. What simple technique can be used to pop deposits out of pits, making the pits much
easier to see. _____________________________________
12. What tools can assist in measuring the depths of a localized corroded area?
a. ____________________________________________
b. ____________________________________________
13. Rivet seams can be checked with a _____________________.
14. Depressions in the tank floor and in areas around roof supports should be checked for
accelerated _____________________.
15. One method to check for penetrations in the bottom is to clean the tank floor and
check for ___________________.
16. One method to check for bottom-side corrosion that is usually not effective is the
______________________________________.
17. Tanks with a welded bottom angle joining the bottom-to-shell should be checked for
__________________________.

18. Other methods to test the tank bottom include: (Describe and include any limits)
a. _______________________________________________________________
b. _______________________________________________________________
c. _______________________________________________________________
d. _______________________________________________________________
e. _______________________________________________________________
19. Tanks that contain dilute acids often are lined with __________.
20. An effective way to locate pinholes and cracks in lead is with ____________.
21. Bulges in a lead liner indicate _________________ behind the liner and are likely
places of ______________________ of the liner.
22. What is a good practice when examining suspect areas in lead lined tanks?
____________________________________
23. Rubber tanks linings can be checked with a _____________ _____________.
24. Holiday testing is used to test _________________.
25. When using a holiday detector it is important that the voltage does not get high enough
to _______________________ the lining.
26. Glass-lined tanks should never be _____________ _____________.
27. What type of lined tanks should be painted a unique color to indicate they have a
special lining? ___________________________

28. What is an effective inspection technique for checking whether there is corrosion
behind a concrete lining? ____________________________
29. When significant corrosion is seen on the roof during the internal inspection, it is
important to erect scaffolding so that ______________________________________
can be taken.
30. If corrosion is found internally on the shell at a specific elevation in a cone roof tank,
it is important to check the ____________________________________ at the same
elevation.
31. What metallurgy should never be hammer-tested? ____________
32. What internal tank component should be hydrostatically tested during an internal
inspection? ___________________________________.
33. Steam heating coils should be inspected for _________________ grooving in the
______________ of the coil with either UT or RT.
34. Pontoons on swing line should be visually examined and checked using either
__________________ _____________ or _________.
35. When hydrotesting a tank consideration should be given to the _______________
__________________ of the shell material.
36. If an atmospheric tank is air tested, the pressure should not exceed ___________
inches of water.
37. A pneumatic test of a tank is good for finding _____________ but is not a good
______________________test.
38. What part(s) of the tank have a very low stress load? _______________________
________________________________

39. The pressure exerted on the sides of a tank is greatest at the _______________ of the
tank.
40. Which of following situations does not appreciably weaken the plate?
a. Crack
b. Locally thinned area
c. Notch
d. Pit

Section 8
1. How can leaking rivets and rivet seams be repaired?
a. _______________________________
b. _______________________________
c. _______________________________
d. _______________________________
2. When riveted seams are seal-welded, all rivets and seams within ________ inches
from the weld should be _______________.
3. Defective rivets can also be replaced with ___________ ____________.
4. List specific requirements when performing weld repairs to rivet heads and seams.
a. _________________________________
b. _________________________________
c. _________________________________
d. _________________________________
e. _________________________________
5. When installing a new floor over an existing floor at least _______ inches of clean
sand, or metal grating or concrete should separate the two floors.
6. When installing a new floor over an existing floor that is cathodically protected, the
old floor should be ____________________.
7. When installing a new floor over an existing floor that is cathodically protected, and
the old floor is not removed, ________________ ________________ should be
placed between the old and new floors.

8. Prior to gouging out a crack, what should be done?
__________________________________
9. Deep pits may be filled with ____________________________________________.
10. Prior to repairing a pit with a coating, the pit should be thoroughly ______________.
11. Leaks in tank roofs are often repaired using a _________ ____________.
Section 9
1. Good inspection records are the basis of an _____________________ inspection
program.
2. Tank records should be kept for the ___________ of the tank.
3. List items that should be documented when internal or external tank inspections are
performed.
a. _________________________________
b. _________________________________
c. _________________________________
d. _________________________________
e. _________________________________
f. _________________________________
g. _________________________________

Other
1. What can happen when the pressure-vacuum vent plugs?
2. What is a "striker plate"?
3. Describe the purpose of the automatic bleeder vent on a floating roof.
4. Why are there special rules when performing weld repairs to leaks in riveted seams or
at rivets?
5. List two disadvantages of foam log seals.

Api 653 study guide

More Related Content

What's hot (20)

Viewers also liked (14)

Similar to Api 653 study guide (20)

Recently uploaded (20)

Api 653 study guide