AST Methods_Practical No. 8.pptx
- 1. Practical No. 8 Antibiotic susceptibility testing
- 2. Antibiotic sensitivity is a term used to describe the susceptibility of bacteria to antibiotics. Antibiotic susceptibility testing (AST) is usually carried out to determine which antibiotic will be most successful in treating a bacterial infection in vivo. Some antibiotics actually kill the bacteria (bactericidal), whereas others merely prevent the bacteria from multiplying (bacteriostatic). Testing for antibiotic sensitivity is often done by: 1. Diffusion methods. 2. Dilution methods for Minimum Inhibitory Concentration determination.(MIC).
- 3. Diffusion methods Kirby-Bauer method or disk diffusion antibiotic sensitivity testing: Small filter paper disks containing antibiotics are placed onto a plate upon which bacteria are growing. The antibiotic diffuses from the disk into the agar . If the bacteria are sensitive to the antibiotic, a clear ring, or zone of inhibition, is seen around the disk indicating poor growth. Using special comparators that interpret the diameter of the zones of inhibition, consequently the organism can be described as resistant, intermediate, or sensitive. Tables are used to determine the breakpoint for each drug.
- 7. Agar disk diffusion method procedure: 1. from a prepared bacterial suspension, dip a swab and seed the surface of an agar plate with the swab then rotate the plate through a 45º angle and streak the whole surface again, then rotate the plate another 90º and streak once more. Discard the swab in disinfectant. 2. Dip the tips of a forceps in 70% alcohol, flame rapidly and allow cooling. 3. Pick up an antibiotic disc with the forceps and place it on the agar surface, press the disk gently using the tips of the forceps. 4. Repeat with eight different antibiotic disks; make sure they are separated evenly from each other. 5. Invert plates and incubate at 37ºC overnight.
- 8. Antibiotics may be also placed in wells made in the agar medium by a cork borer. Or antibiotics may be incorporated with the melted agar and poured together in Petri dishes, in this case each dish will contain only on antibiotic. when two antimicrobial agents act at the same time on the same microbial population, the effect may be either indifference. 1+1= 1 addition. 1+1=2 synergism. 1+1= 3 antagonism 1+1= 1/2
- 9. 6. Using a ruler measure the diameter of any zones of inhibition and record your results, the results must be compared with values listed in standard charts as shown in the interpretative chart below: Antibiotic Disk concentration Diameter of zone of inhibition Resistant Intermediate Susceptible ampicillin 10 microgram 11 or less 12-13 14 or more cephalothin 30 microgram 14 or less 15-17 18 or more chloramphenicol 30 microgram 12 or less 13-17 18 or more gentamicin 10 microgram 12 or less 13-14 15 or more penicillin 10 U 20 or less 21-28 29 or more Polymyxin B 300 U 8 or less 8-11 12 or more sulphonamide 300 microgram 12 or less 13-16 17 or more tetracycline 30 microgram 14 or less 15-18 19 or more
- 10. Other methods to test antimicrobial susceptibility include the E-test also based on antibiotic diffusion. The Epsilometer test (usually abbreviated Etest): is a laboratory test used to determine whether or not a bacterium is susceptible to an antibiotic. The Etest is basically an agar diffusion method. The Etest utilises a rectangular strip that has been impregnated with the drug to be studied. A lawn of bacteria is inoculated onto the surface an agar plate and the Etest strip is laid on top; the drug diffuses out into the agar, producing an exponential gradient of the drug to be tested. There is an exponential scale printed on the strip. After 24 hours of incubation, an elliptical zone of inhibition is produced and the point at which the ellipse meets the strip gives a reading for the (MIC) of the drug.
- 14. Dilution methods for Minimum Inhibitory Concentration determination.(MIC) The most commonly employed methods are the tube dilution method. The tube dilution test is the standard method for determining levels of microbial resistance to an antimicrobial agent. Serial dilutions of the test agent are made in a liquid microbial growth medium which is inoculated with a standardized number of organisms and incubated for a prescribed time. The lowest concentration (highest dilution) of test agent preventing appearance of turbidity (growth) is considered to be the minimal inhibitory concentration (MIC). At this dilution the test agent is bacteriostatic. The minimal bactericidal concentration (MBC) or the
- 15. Procedure of (MIC): 1. Number sterile capped test tubes 1 through 9. All of the following steps are carried out using aseptic technique. 2. Add 2.0 ml of tetracycline solution (100 ug/ml) to the first tube. Add 1.0 ml of sterile broth to all other tubes. 3. Transfer 1.0 ml from the first tube to the second tube. 4. Using a separate pipette, mix the contents of this tube and transfer 1.0 ml to the third tube. 5. Continue dilutions in this manner to tube number 8, being certain to change pipettes between tubes to prevent carryover of antibiotic on the external surface of the pipette. 6. Remove 1.0 ml from tube 8 and discard it. The ninth tube, which serves as a control, receives no tetracycline. 7. Suspend to an appropriate turbidity several colonies of the culture to be tested in 5.0 ml of Mueller-Hinton broth to give a slightly turbid suspension. 8. Dilute this suspension by aseptically pipetting 0.2 ml of the suspension into 40 ml of Mueller-Hinton broth. 9. Add 1.0 ml of the diluted culture suspension to each of the tubes. The final concentration of tetracycline is now one-half of the original concentration in each tube. 10.Incubate all tubes at 35oC overnight. 11.Examine tubes for visible signs of bacterial growth. The highest dilution without growth is the minimal inhibitory concentration (MIC).