Autel MaxiFlash Elite J2534 ECU Programming Tool User Manual

Table of Contents
1. INTRODUCTION .......................................................................................1
1.1 BACKGROUND.............................................................................................1
1.2 J2534 - A SOLUTION ARRIVES....................................................................2
1.3 PASS-THRU VEHICLE INTERFACE ..............................................................2
2. GETTING TO KNOW MAXIFLASH PRO..............................................3
2.1 FRONT PANEL.............................................................................................3
2.2 REAR PANEL...............................................................................................5
2.3 POWER UP ..................................................................................................7
2.4 SPECIFICATIONS .........................................................................................7
2.5 ACCESSORIES INCLUDED ............................................................................9
2.6 PRODUCT TROUBLESHOOTING ..................................................................10
3. DRIVER SETUP & NETWORK CONFIGURING ................................11
3.1 DRIVER SETUP ...........................................................................................11
3.2 NETWORK CONFIGURATION......................................................................13
4. REPROGRAMMING WITH J2534 DEVICE.........................................18
5. COMPLIANCE INFORMATION............................................................20
6. WARRANTY AND SERVICE ..................................................................21
6.1 LIMITED ONE YEAR WARRANTY ..............................................................21
6.2 SERVICE PROCEDURES ..............................................................................21

1
1. Introduction
1.1 Background
The days of diagnosing and repairing automobiles without a laptop
beside you are quickly fading. Newer vehicles include a large
number of onboard computers that are each dedicated to performing
specific tasks. Common onboard computers in newer vehicle
include the Engine Control Module (ECM), Transmission Control
Module (TCM), Fuel Injection Control Module (FICM), Anti-lock
Brake System (ABS), Body Control Module (BCM) and numerous
other control modules to manage every electronic system from
power door locks to crash data.
Each onboard computer is programmed at the factory with software
enabling it to perform certain tasks. Inside the ECM is software
containing hundreds or even thousands of parameters to control
spark, fuel, idle, cruising, emissions, economy, drivability, and
performance. Likewise, a TCM will have software to control how
the transmission and torque converter function. Sometimes, after
the vehicle is shipped from the automaker, updates are released to
improve emissions, fuel economy, drivability, performance, or
specific bugs in the original software that have caused warranty
issues. Updating this software can be a proactive fix because often
it will resolve problems that a customer hasn’t reported or noticed
yet.
The practice of updating software in these modules is more
commonly known as flash reprogramming. At new car dealerships,
flash reprogramming is relatively straight forward because service
technicians are connected to the automaker and have the expensive,
specialized dealer service tools dedicated to reprogramming. The
independent repair shops have faced a more difficult challenge
because most shops typically service more than one make of
vehicles. This increases the complexity, cost and training required
to operate dozens of different factory service tools.

2
1.2 J2534 - A Solution Arrives
In 2000, the Environmental Protection Agency (EPA) had been
watching this issue and decided to take action. The EPA requested a
standard be developed within the SAE that led to J2534, a
mandated specification to which automakers who sell vehicles in
the United States must conform. The original J2534 specification
was later updated to J2534-1 in order to support all automakers.
The EPA mandate requires automakers to support aftermarket repair
shops with J2534-1 flash reprogramming for any emissions related
computer modules on a vehicle that can be reprogrammed by a new
car dealership. This mandate took effect for all 2004 and newer
vehicles.
SAE J2534 is a standard devised of two independent parts:
subscription software and a J2534 compliant Pass Thru vehicle
interface. The subscription software comes directly from the
automaker, runs on your shop PC or laptop, and can either be
web-based or CD-based. The subscription fees are charged
differently for each automaker.
1.3 Pass-Thru Vehicle Interface
The second part of the system is a SAE J2534 compliant Pass-Thru
vehicle interface. This device acts as a gateway between the
vehicle’s onboard computers and the technician’s personal computer.
It translates messages from the PC into the protocols used by the
automobile and vice versa.
Performing J2534 reprogramming requires computer knowledge
and experience. The technician will need to operate a laptop or
desktop, the Pass-Thru device, and the reprogramming software.
Operation will also require a good high-speed connection to the
Internet such as DSL, Cable, or T1.

3
2. Getting to Know MaxiFlashPro
Thank you for choosing the MaxiFlash®
Pro Reprogramming
Device! This multi-protocol Pass-Thru vehicle interface is a fully
compliant SAE J2534-1 & SAE J2534-2 (March 2006) device,
specially designed to provide users with convenient PC
communication and ECU reprogramming capabilities on any
modern vehicle diagnostic bus, and offer the most significant
features desired by OEM customers: reliability, fast performance
and flexibility.
2.1 Front Panel
The MaxiFlash®
Pro Pass-Thru device supports three ways of PC
connection: Ethernet, USB and Bluetooth, which make PC
communication and vehicle reprogramming all the more convenient
and easy for technicians. These three connection ports to the PC are
available in the front panel of the device.
1) Status Lights
There are 6 status lights on the front panel of the reprogramming
tool, which indicates the Pass-Thru interface’s working status as
well as the hardware conditions, and are very useful for
troubleshooting the device’s communication or connection to the
Vehicle or PC. Please refer to Table 1 for detailed description of
the status lights.

4
TABLE 1—STATUS LIGHTS ON THE FRONT PANEL
Light Description
Power Illuminates solid green when powered on.
Error Illuminates solid red when serious hardware failure
occurs. Please call technical supports for assistance.
Note: This status light turns on automatically every
time when the device is power up, which is a normal
self-test procedure, and it will turn off automatically
later when the device starts working normally.
Bluetooth Illuminates solid green when connected via
Bluetooth communication.
Ethernet Illuminates solid green when connected via the
Ethernet serial cable.
USB Illuminates solid green when the device is properly
connected and communicating with the PC via the
USB cable.
Vehicle Flashes green when communicating with the
vehicle’s network.
Note: Do not disconnect while this status light is
on! If you interrupt the flash reprogramming
procedure while the vehicle’s ECU is blank or only
partially programmed, the module may be
unrecoverable.
2) USB Port
The USB port provides the easiest connection between the
device and the PC via a USB cable, and is used to control the
device from the software application running on the PC.

5
3) Ethernet Port
The Ethernet port connects the device to the PC directly or
through an existing network via an Ethernet cable, which
supports longer range and higher performance.
NOTE: There’re two status lights at the bottom corners
alongside the Ethernet Port, which illuminate when the
device is properly connected to the PC or an existing
network through the Ethernet Cable.
4) Bluetooth Antenna
The Bluetooth antenna, which offers higher bandwidth and
distance range, can be detected and paired to Autel’s MaxiSys
diagnostic tablet and serves as a Vehicle Communication
Interface (VCI) device for data transmission.
2.2 Rear Panel
Connections to the power adapter, vehicle, external
programming voltage, and analog inputs are available on the rear
panel.
1) Power Port
The power port (DC 12V) connects the device and the power
source with the adapter, which supplies power to the
reprogramming tool.

6
2) Vehicle Connector
The Vehicle connector connects the device to the vehicle’s DLC
via a standard high density DB-26 MVCI – OBDII cable.
3) External Programming Voltage Output
The external programming socket provides the user with access
to the 5-20V programming voltage. This is used for Mitsubishi,
Subaru or any other vehicle that needs voltage on an additional
connector.
4) A/D Inputs
The 12-bit analog inputs are setup for an input range of 0 -
27.5VDC and are electrically protected against reverse voltage
and over voltage conditions. The Mating connector is a High
Density DB-15.
TABLE 2 – GENERAL PURPOSE ANALOG INPUTS
Pin Function Direction
2 Channel 6 In
4 Channel 3 In
6 Battery Voltage Out (200mA max)
8 Channel 4 In
10 Channel 1 In
12 Channel 5 In
14 Channel 2 In
1,3,5,7,9,
11,13,15
Ground

7
2.3 Power Up
The Pass-Thru vehicle reprogramming device can be powered either
via the vehicle DLC, or the external power adapter.
 Vehicle Power Supply
1) Connect the MVCI – OBDII cable to the reprogramming
tool.
2) Find DLC on vehicle.
A plastic DLC cover may be found for some vehicles and you
need to remove it before plugging the OBDII cable.
3) Plug OBDII cable to the vehicle’s DLC.
4) Wait for the reprogramming tool to power up.
 External DC Power Supply
1) Locate the power port of the device.
2) Connect the device and the power source with the power
adapter.
3) Wait for the reprogramming tool to power up.
The external power supply is necessary for off-board
reprogramming, and since this reprogramming tool does not
receive power from the PC’s Ethernet or USB ports, it is also
needed when the device is communicating applications on the PC.
NOTE: The external power supply does not support power
charging to the vehicle battery.
2.4 Specifications
The MaxiFalsh®
Pro Reprogramming Device is powerfully
featured to be desired by all OEM customers:

8
 Supports simultaneous communication definition in J2534-1,
running 3 protocols at the same time, which greatly improves
reprogramming and diagnostic speed.
 Supports multiple device connections to the PC, which can
operate diagnostic and reprogramming functions on more than
one vehicle at the same time.
 Embedded with the ARM9 Dual-core processor (clocked up to
500MHz), which further boosts the communicating speed.
 Rugged aluminum case with non-slip rubber end caps, capable
of withstanding harsh environment.
Check up detailed specifications in the following table:
TABLE 3 – DEVICE SPECIFICATIONS
Name Value
Input Voltage Range 6VDC to 26VDC
Supply Current 350mA @ 6VDC
200mA @ 12VDC
110mA @ 24VDC
Operating Temperature 0℃ to +60℃ (ambient)
Storage Temperature -65℃ to +100℃ (ambient)
Dimensions Length: 183.8 mm (7.23")
Width: 135.5mm (5.33")
Height: 41 mm (1.6")
Weight 0.54kg (1.20lb)

9
Bus Protocols
 Primary CAN / ISO15765 / GMLAN
 Secondary CAN / ISO15765 / GMLAN (Dual or Single
Wire)
 Ford SCP (J1850PWM)
 GM Class2 (J1850VPW)
 KWP2000 (ISO9141 / 14230)
 Chrysler SCI (J2610)
Other
 Compliant to SAE J2534-1 (2004) and J2534-2 (2006)
reprogramming standards
 Compliant to ISO 22900-1 MVCI physical layer
 Programming voltage on all J1962 pins (except 4, 5, and 16)
or Aux
 Ground pins 1,2,9,12, or 15
2.5 Accessories Included
1) User’s Manual - Instructions on tool operations
2) MVCI to OBDII Cable - provides power to tool and
communicates between tool and vehicle, high density
DB-26
3) USB Cable - allows easy connection to PC
4) Ethernet Cable - connects to PC or an existing network
5) Bluetooth Antenna – receives wireless network signals
6) Power Adapter - supplies power to the reprogramming
tool.
7) CD - includes user’s manual, software development kit,
device driver, etc

10
The following accessories are optional items according to
your demand, available and buyable from Autel directly or
the local agents or dealers:
8) Analog Input Line - measures voltage levels
9) External Programming Voltage Output Line - provides
access to the 5-20V programming voltage
2.6 Product Troubleshooting
This part describes problems that you may encounter while using
the reprogramming tool.
Vehicle Linking Error
A communication error occurs if the reprogramming tool fails to
communicate with the vehicle’s control module when perform the
program re-flash. You need to do the following check-ups:
 Verify that the ignition is ON.
 Check if the reprogramming tool’s OBD II connector is
securely connected to the vehicle’s DLC.
 Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and continue the operation.
 Verify the control module is not defective.
PC Communication Error
If you cannot communicate the device to the PC, you need to do
the following check-ups:
 Verify the reprogramming tool is powered, and the green
power LED is illuminated.
 Check if there is any firewall software interfering with the
connection port.
 Check if the green status light is illuminated for Ethernet,
USB, or Bluetooth.
If these issues have been addressed, verified, and you are still
having trouble, please contact technical supports for assistance.

11
3. Driver Setup & Network Configuring
3.1 Driver Setup
In order for the Pass-Thru Device to operate correctly with the
re-flashing and diagnostic applications on the target PC, you will
need to first install the MaxiFlash Pro J2534 device driver onto the
PC that will control the device.
To setup the J2534 Pass-Thru device driver, you will need the
followings:
 CD with the device driver program
 PC or laptop with USB ports
 J2534 Pass-Thru reprogramming tool
 USB cable
NOTE: The following steps may vary depending on the
operating system or components that are installed on your
computer, but in general this is the standard installation
process.
1) Insert the driver installation CD to your PC. The driver
installation wizard will load momentarily.
2) Click on ―Next‖ on the welcome page.
3) Select ―Next‖ on the installation location and installation
name. It is recommended not to change the default settings;
otherwise the computer may have a hard time recognizing
the driver.
4) Click ―Install‖ and the driver program will be installed onto
your PC.
NOTE: During this part of the process a MS-DOS style
window will pop up and may remain on your screen for a
short while, which is perfectly normal. Do not attempt to

12
close the MS-DOS style window manually as this will
prevent the device driver being installed successfully, it
will close automatically when the device driver installation
is complete.
5) Connect the Pass-Thru device to the PC with the supplied
USB cable, a ―Found New Hardware Wizard‖ window will
pop up.
6) Select ―Install the software automatically (Recommended)‖,
click on ―Next‖, and Windows will search for the driver
software automatically.
7) Select the ―MaxiFlash Pro‖ program and click on ―Install‖.
8) When the MaxiFlash Pro device driver program is
successfully installed, you should be able to see the ―Maxi
Flash Pro‖ entry in the Device Manager under ―Maxi Pass
Thru Serial‖. (Figure 3.1)
Figure 3.1

13
NOTE: If the driver installation is not complete or
unsuccessful, or the PC still can’t recognize the device, an
Error or Question mark will display beside the entry icon.
Please try installing the driver program again by clicking
the entry, then select start auto searching for the software,
or manually locate the specific file that contains the driver
program.
3.2 Network Configuration
The MaxiFlash Pro device program also provides users with an
easy and convenient application interface for operating network
configurations to ensure proper communication between the
Pass-Thru device and the PC.
3.2.1Ethernet Connection
Using wired network between the Pass-Thru device and the PC,
users can choose either way of connection described as below:
 Connecting to a PC Directly
1. Connect the PC to the Pass-Thru device with the
supplied Ethernet cable.
2. Open ―My Network Places‖ Properties.
3. In the Properties window, under the LAN or
High-Speed Internet heading, right click on the ―Local
Area Connection‖ and select ―Properties‖.
4. Now a new window should pop up, titled ―Local Area
Connection Properties‖. Here you need to select the
Internet Protocol (TCP/IP) option, and then click on the
―Properties‖ button.

14
Figure 3.2
5. Again a new window titled "Internet Protocol (TCP/IP)
Properties" will pop up. In this window, you need to
select "Use the following IP Address" radio button, and
set the specific IP address (take the value shown in
Figure 3.3 for example), then click on ―OK‖.
NOTE: For specific IP address information please
contact your network administrator.

15
Figure 3.3
6. After all the above properties settings have been
properly set, users can continue on completing the
network configuring procedure, please refer to the
detailed operation guidance in 3.2.2. MaxiFlash
Configuration – Wired Network.
 Connecting to an Existing LAN
1. Connect the Pass-Thru device to a local network with
the supplied Ethernet Cable.
2. On most LANs, MaxiFlash Pro can obtain its IP address
automatically using DHCP.
3.2.2MaxiFlash Configuration – Wired Network
1) Connect the Pass-Thru device to the PC or an existing LAN
with the supplied Ethernet cable.
2) Power up the device by the external power supply; verify the
green Power status light on the front panel is on.

16
3) Verify the Ethernet status light is on.
4) Click on ―All Programs‖ from Windows Start Menu, find the
―MaxiFlash Pro‖ entry under ―Autel‖, click on
―MaxiFlashCFG‖, and wait for the program interface to pop
up. (Figure 3.4)
Figure 3.4
5) Select the ―Settings‖ tab to set up the network configuration.
6) Select ―DHCP‖, if you are connecting to the local area
network, the MaxiFlash Pro will obtain the IP address
automatically. Select ―Manual‖, if you are connecting to the
PC directly for the first time, and then set the IP address on
your own.
7) Click on the ―Apply‖ button to save the network
configuration.

17
3.2.3Firmware Update
This function allows you to update the driver software for the
Pass-Thru device through the PC. Make sure the PC is
connected to the Internet before using this function.
1) Connect the Pass-Thru device to the PC with the supplied
Ethernet cable or USB cable.
2) Power up the device by the external power supply; verify the
green Power status light on the front panel is on.
3) Verify the Ethernet or USB status light is on.
4) Click on ―All Programs‖ from Windows Start Menu, find the
―MaxiFlash Pro‖ entry under ―Autel‖, click on
―MaxiFlashCFG‖, and wait for the program interface to pop
up. (Figure 3.4)
Figure 3.5
5) Select the ―Update‖ tab and the update agent will
automatically check for the available update online.
6) Press the ―Next‖ button to install the newest firmware.
7) Press the ―Cancel‖ button to exit.

18
4. Reprogramming with J2534 device
To reprogram vehicles using OEM software, you can find a list
below of websites that offer subscription software, or visit
http://etools.org/ website to find out more ECU re-flash
applications from the OEMs.
Using additional OEM software, the MaxiFlash Pro can be used
as a Pass-Thru diagnostics tool as well, which allows users to
read and clear Diagnostic Trouble Codes (DTCs) and data log
PIDS, collect sensor data and log generic OBDII data etc.
Since J2534 allows multiple devices to be connected at once,
you must tell the software you want to use the MaxiFlash Pro.
Every application will have a different way to select the device,
so please consult the software manual.
TABLE 4 – LIST OF AUTOMAKERS’ SERVICE WEBSITES
Automaker Website
BMW http://www.bmwtechinfo.com/
Mini http://www.minitechinfo.com/
Porsche http://www.porsche.com/
Chrysler, Jeep,
Dodge
http://www.techauthority.com/

19
Automaker Website
Ford, Lincoln,
Mercury,
http://www.motorcraft.com/
Land Rover http://www.landrovertechinfo.com/
Volvo http://www.volvotechinfo.com/
Cadillac, Chevrolet,
Daewoo, GM, GEO,
Pontiac, Buick,
Saturn, SAAB
http://www.gmtechinfo.com/
Acura, Honda http://www.serviceexpress.honda.com/
Isuzu http://www.isuzutechinfo.com/
Mazda http://www.mazdaserviceinfo.com/
Mercedes http://www.startekinfo.com/
Mitsubishi http://www.mitsubishitechinfo.com/
Nissan http://www.nissan-techinfo.com
Toyota, Lexus, Scion
http://techinfo.toyota.com/
Volkswagen http://www.erwin.volkswagen.de/erWin
VW
Audi http://erwin.audi.de/erWinAudi
NOTE: When reprogramming onboard, always make sure
the vehicle battery is fully charged and in good working
condition. During reprogramming there is a risk of having the
operation failure if voltage falls below the proper operating
voltage. Sometimes a failed operation can be recovered, but
there is a chance that failed reprogramming could ruin the
control module. We recommend connecting an external
battery charger to the vehicle to ensure a successful
operation.

20
5. Compliance Information
FCC COMPLIANCE FCC ID: WQ82012J2534
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures: ⅰ. Reorient
or relocate the receiving antenna. ⅱ. Increase the separation between the
equipment and receiver. ⅲ. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. ⅳ. Consult the dealer or
an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
RoHS COMPLIANCE
This device is declared to be in compliance with the European RoHS Directive
2011/65/EU.
CE COMPLIANCE
This product is declared to conform to the essential requirements of the
following Directives and carries the CE mark accordingly: EMC Directive
2004/108/EC R&TTE Directive 1999/5/EC Low Voltage
Directive 2006/95/EC

21
6. Warranty and Service
6.1 Limited One Year Warranty
Autel warrants to its customers that this product will be free from
all defects in materials and workmanship for a period of one (1)
year from the date of the original purchase, subject to the following
terms and conditions:
1) The sole responsibility of Autel under the Warranty is limited
to either the repair or, at the option of Autel, replacement of
the Pass-Thru device at no charge with Proof of Purchase.
The sales receipt may be used for this purpose.
2) This warranty does not apply to damages caused by improper
use, accident, flood, lightning, or if the product was altered or
repaired by anyone other than the Manufacturer’s Service
Center.
3) Autel shall not be liable for any incidental or consequential
damages arising from the use, misuse, or mounting of the
device. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitations may not apply
to you.
4) All information in this manual is based on the latest
information available at the time of publication and no
warranty can be made for its accuracy or completeness. Autel
reserves the right to make changes at any time without
notice.
6.2 Service Procedures
If you have any questions, please contact your local store,
distributor or visit our website at www.auteltech.com.
If it becomes necessary to return the tool for repair, contact your
local distributor for more information.

Autel MaxiFlash Elite J2534 ECU Programming Tool User Manual

More Related Content

What's hot (12)

Viewers also liked (20)

Similar to Autel MaxiFlash Elite J2534 ECU Programming Tool User Manual (20)

More from BuyobdtoolShop (20)

Recently uploaded (20)

Autel MaxiFlash Elite J2534 ECU Programming Tool User Manual