Behavior of plan irregularites using composite members by varying column spacing and by varying height of the structure

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________________
Volume: 05 Issue: 08 | Aug-2016, Available @ http://ijret.esatjournals.org 73
BEHAVIOR OF PLAN IRREGULARITES USING COMPOSITE
MEMBERS BY VARYING COLUMN SPACING AND BY VARYING
HEIGHT OF THE STRUCTURE
B Kavitha1, Varuna Koti2, Ruchir A J3
1
M.Tech, Department of Civil Engineering, Global Academy of Technology, Bengaluru-560098
2
Assistant Professor, Department of Civil Engineering, Global Academy of Technology, Bengaluru-560098
3
Assistant Professor, Department of Civil Engineering, CMR Institute of Technology, Bengaluru-560037
Abstract
Several studies proofs that the weaker columns has low seismic resistance, for this it is need to make the column stronger. The
stronger columns can be obtained by many ways, here in this paper steel-concrete composite columns are considered. Use of
composite columns in construction reduces the cross-section of the columns throughout the building and also increases the
lateral-load resisting capacity to columns. The models consists of G+10, G+15, G+20 stories of Rectangular, L, T and plus
shaped structures in which column spacing are varied as 3m, 4m, 5m and 6m along both directions in all structures. F or all
models the composite-column of size 450x450mm (ISMB 250) is kept constant, only the beam size has been varied accordingly
while modeling a structure. The Response Spectrum analysis is done for all the buildings using ETABS version 15. Study is based
on the performance of a multi-story building with plan irregularity under major earthquake forces by considering parameters like
displacement, storey shear and drifts. Even though the cross section of the column considered is very small for tall buildings, the
structure behaves stiff for severe seismic zone-V and also for different conditions; this is done by introducing steel-concrete
composite column in a given building. Hence it is concluded that the use of composite columns in construction resists the lateral
forces for many vulnerable conditions.
Keywords: Composite Column, Irregular Structure, Seismic Zone, Varying Height, Column Spacing.
--------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
As we know earthquakes are the unpredictable natural
disasters, from which it is very difficult for saving life and
engineering properties against it. Structures which have
regular geometry, stiffness in plan and elevation,
distribution of mass uniformly throughout the building
suffer little damage than the irregular configurations during
earthquakes. But in modern days, with more advancement in
the rapid growth of urbanization and for aesthetic purpose
buildings are constructed with irregular structural
configurations. This building configuration provides to
irregular distribution of strength, mass and stiffness from
this it may lead to damage of the frame during earthquakes.
At present days the engineers and architects are planning
towards irregular configurations as it is a demand and
requirement for growing population.
Understanding the need of a structural configuration is
required in the earthquake engineering. A structure which is
designed for earthquake proof is very often, buildings which
are more stable will be more expensive. For small buildings
RC structures are economical and convenient, where as for
tall buildings RC members are not economical due to its
hazardous form work, span restriction, increased self weight
and less stiffness. To over-come this disadvantages a
composite structures has been introduced, composite
construction combines properties of both structural steel and
reinforced concrete with speedy construction,lessercost and
reduction in size etc.
Several studies proofs that the weaker columns has low
seismic resistance, for this it is need to increase or to make
the column stronger. The stronger columns can be obtained
by many ways, here in this thesis steel-concrete composite
columns are considered.
1.1 Composite Column
It is a structural element which combines a structural steel
with reinforced concrete from which it provides satisfactory
load carrying capacity to sustain axial load or combination
of both bending moment and axial loads.
This combination increases the stiffness and ultimate
strength of columns which is very suitable for columns and
other compressive members. The integral and interactive
performance of concrete and structural steel elements make
the composite column, these are very cost effective
structural member in building. Composite columns have
many merits over a conventional RCC and structural steel
columns. In practice the composite columns are of two types
they are (a) concrete filled and (b) concrete encased
columns.

_______________________________________________________________________________________________
Fig-1: Cross-sections of fully and partially concrete encased
columns.
In our present study concrete fully encased composite
columns are considered for the modeling and analysis of a
regular/rectangular structure and also for horizontal irregular
structures.
1.2 Need for Present Study
 Several studies show that the weaker columns have low
seismic resistance, for this it is required to make column
stronger.
 The stronger columns can be obtained by many ways,
here in this study steel-concrete composite columns are
considered. Use of composite columns in construction
reduces the cross-section of the columns throughout the
building and also increases the lateral-load resisting
capacity to columns.
 Hence there is need for strong columns in construction
especially for irregular buildings and also when it is
required for long span beams in tall-buildings.
1.3 Objective of the Study
 To understand the performance of composite structures
for variable column spacing and also for varying height
under seismic Zone V.
 To understand the behavior of regular/rectangular and
plan irregularities of composite members for the above
mentioned conditions.
 To study the performance of a multi-story building with
plan irregularity under major earthquake forces by
considering parameters like displacement, storey shear
and drifts.
2. BUILDING DESCRIPTION
In our study fourdifferent configurations has been chosen in
which one is rectangular and remaining three are of plan
irregularities. The plan, floor to floor height, column size,
slab thickness, floor finish loads, wall loads, live loads and
Response-spectra data remains same for all the models.
The models consists of G+10, G+15, G+20 stories of
Rectangular, L, T and plus shapes in which column spacing
are varied as 3m, 4m, 5m and 6m along both directions. For
all models the composite-column of size 450x450mm
(ISMB 250) is kept constant, only the beam size has been
varied accordingly while modeling a structure. The
Response Spectrum analysis is made for all the buildings
using a ETABS version 15.
Table-1 Common Specifications for all Structures
Layout of plan • 5bays x
4bays
Support conditions • Fixed
Height of each storey • 3m
Grade of concrete • 40 Mpa
Grade of reinforced steel • Fe500
Structural steel considered • ISMB250
Thickness of main wall • 200mm
Slab thickness • 125mm
Seismic Zone • V
(Z=0.36)
Soil type • II
Importance factor • 1
Response reduction factor • 5
Damping ratio • 5%.
Fig-2: Rectangular Shape

_______________________________________________________________________________________________
Fig-3: L-Shape
Fig-4: T-Shape
Fig-5: Plus-Shape
3. RESULTS AND DISCUSSION
The research work is took place to compare the dynamic
response of buildings with steel-concrete composite column.
Totally 48 models/structures are taken for dynamic analysis
which includes Response Spectrum method. Code used is
IS-1893 (part-I):2002 for Response Spectrum method from
which storey shear, storey drift, and storey displacement
results for seismic zone-V are obtained.
Chart -1: Storey Displacement v/s varying column spacing
for G+10storey along X-dir

_______________________________________________________________________________________________
From the Chart-1, 2 and 3 it is clear that regular/rectangular
structure has been undergone less displacement than the
other structures. After rectangular structure, Plus-shape
building has undergone less displacement compare to L and
T-shape buildings. In G+10 and G+15 stories the maximum
displacement observed in L and T-shaped buildings, but in
G+20storey building the displacement is observed
maximum only in L-shape building.
Chart-4: Storey Drift v/s varying column spacing for
G+10storey along X-dir
From the Chart-4, 5 and 6 it is consequent that
regular/rectangular structure has undergone less storey drift
compare to the remaining configurations. After rectangular
structure the Plus-shape has got less storey drift compare to
L and T-shape structures. In G+10storey the storey-drift is
observed maximum in both L and T-shaped structures, but
in G+15and G+20storey the storey drift is observed
maximum only in L-shape.
Chart-7: Base Shear v/s varying column spacing for

_______________________________________________________________________________________________
From the Chart-7, 8 and 9 it is found that the variation of
storey-shear values for rectangular structure is more
compare to the irregular structures. As seen above the
rectangular structure gives maximum base shear values as it
supports minimum displacement due to lateral force.
4. CONCLUSION
 The irregularity present in the structure will alter the
displacement i.e. as the irregularity increases the lateral-
displacement also increases.
 As the column spacing increases the storey displacement
is observed maximum in both L and T-shape buildings,
but as the storey height increases the storey displacement
get maximum only in L-shape buildings. Therefore we
conclude that L-shape structure is more critical
compared to the Rectangular, T and Plus shape
structures.
 The maximum storey-drift varies from one storey to
other in G+10, G+15 and G+20 storey models,
depending upon the model configuration and also on the
varying column spacing.
 The L-shape model is found to be critical with the
maximum drift values when compared to the other
structures.
 Base shear of an irregular configured structure will be
less when compared with regular building. Storey shear
is found lower in the models of Plus-shape buildings.
 In performance point base shear gets reduced when the
irregularity increases from which the structure becomes
more vulnerable with the increase in its amount of
irregularity.
 Even though the cross section of the column considered
is very small for tall buildings, the structure behaves stiff
even for severe seismic zone-V with different conditions,
this is done by introducing steel-concrete composite
column in a given building.
 Hence it is concluded that the use of composite columns
in construction resists the lateral forces for many
vulnerable conditions.
REFERENCES
[1]. B Shivakumara Swamy.et.al.“Influence of strong
column & weak beam concept, soil type and seismic zone
on seismic performance of r c frames from pushover
analysis”, International Journal of Research in Engineering
and Technology, Volume: 04 Special Issue: 04, May-2015.
[2]. Hajira Nausheen1, Dr.H.Eramma, “Comparison of
Seismic Behavior of a Structure with Composite and
Conventional Columns”, International Research Journal of
Engineering and Technology , Volume: 02 Issue: 08 , Nov-
2015.
[3]. Ahmed H. El-Masry, Mohamed A. Dabaon, Tarek F. El-
Shafiey, Abd El-Hakim A. Khalil, “Investigation on an
Innovative Way to Connect RC Beam and Steel Column”,
International Journal of Civil, Environmental, Structural,
Construction and Architectural Engineering Vol:9, No:4,
2015.
[4]. Amir Parviz Khosravi Amiri and Elias Behradi Mehr
(Bakhsat) , “Analysis of composite columns based on
performance”, Canadian Journal of Pure and Applied
Sciences, Vol. 9, No. 2, pp. 3481-3485, June 2015.
[5]. Prof. Vijay S Sawant, Prof. Yogesh R Suryawanshi,
Aniket V Renavikar, “Survey on Comparison of Steel and
Concrete Composite Beam Column Connections”,
International Journal of Innovative Research in Science,
Engineering and Technology, Vol. 4, Issue 4, April 2015.
[6]. Prof. Swapnil B. Cholekar, Basavalingappa S. M,
“Comparative analysis of multistoried RCC and composite
building due to mass irregularity”, International Research
Journal of Engineering and Technology, Volume: 02 Issue:
04 | July-2015.
[7]. Rucha S. Banginwar, M. R. Vyawahare, P. O. Modani,
“Effect of Plans Configurations on the Seismic Behavior of
the Structure By Response Spectrum Method, International
Journal of Engineering Research and Applications”, Vol. 2,
Issue 3, May-Jun 2012.
[8]. C. C. Weng, S. I. Yen,and C. C. Chen, “Shear strength
of concrete-encased composite structural members, journal
of structural engineering”, October 2001.
[9]. Shweta A. Wagh.et.al. “Comparative Study of R.C.C
and Steel Concrete Composite Structures”, Journal of
Engineering Research and Applications, Vol. 4, Issue
4(Version 1), pp.369-376, April 2014..
[10]. D. R. Panchal and P. M. Marathe, “Comparative Study
of R.C.C, Steel and Composite (G+30 Storey) Building”,
Institute of Technology, Nirma university, Ahmedabad –
382 481, December 2011.
[11]. Mr. Nitish A. Mohite1, Mr. P.K.Joshi2, Dr. W. N.
Deulkar, “Comparative Analysis of RCC and Steel-
Concrete-Composite (B+G+ 11 Storey) Building”,
International Journal of Scientific and Research
Publications, Volume 5, Issue 10, October 2015.
[12]. Syed Fahad Ali1 S. A. Bhalchandra, “Study on
Seismic Analysis of RCC and Steel-Concrete Composite
Structure and Cost Comparison with Different Support
Conditions”, International Journal for Scientific Research &
Development| Vol. 3, Issue 09, 2015.
[13]. Raghavendra. D B1 Prof. Kashinath Patil, “Study on
the Response of Steel Moment Resisting Frame with
Vertical Setback Subjected to Lateral Loads”, International
Journal for Scientific Research & Development| Vol. 3,
Issue 04, 2015.
BIOGRAPHIES
B Kavitha, M.Tech Student, Department of
Civil Engineering, Global Academy of
Technology, Bengaluru -560098
Varuna Koti Asst. Professor, Department of
Civil Engineering, Global Academy of
Technology, Bengaluru -560098
Ruchir A J, Asst. Professor, Department of
Civil Engineering CMR Institute of
Technology, Bengaluru.

Behavior of plan irregularites using composite members by varying column spacing and by varying height of the structure

More Related Content

What's hot (18)

Viewers also liked (20)

Similar to Behavior of plan irregularites using composite members by varying column spacing and by varying height of the structure (20)

More from eSAT Journals (20)

Recently uploaded (20)

Behavior of plan irregularites using composite members by varying column spacing and by varying height of the structure