ASL Intercom BS15

BS 15

SINGLE CHANNEL BELTPACK

CONTENTS

1.0 GENERAL DESCRIPTION .......................................... 3
2.0 UNPACKING ............................................................... 3
3.0 INSTALLATION ........................................................... 3
4.0 FRONT PANEL CONTROLS ...................................... 4
5.0 REAR PANEL CONNECTORS ................................... 5
6.0 INTERNAL CONTROLS .............................................. 5
7.0 CABLING .................................................................... 6
8.0 PARTY LINE, TECHNICAL CONCEPT ....................... 7
9.0 WARRANTY ............................................................... 7
10.0 TECHNICAL SPECIFICATIONS ................................. 7

User Manual BS 15 / Issue 2010 ASL Intercom, The Netherlands.

2 User Manual BS 15 / Issue 2010 ASL Intercom, The Netherlands. |

1.0 GENERAL DESCRIPTION

The BS 15 is a portable single channel user The unique ASL CALL system provides both
station housed in a strong ABS case. a flashing red LED and a very distinctive and
characteristic sound signal. Smooth operation
On the front panel are a Volume (listen level) is guaranteed with the CALL button. A
control, a Talk and a Call button with LED momentary push makes the red LED flash,
indicators, a sidetone trimmer and a buzzer whilst holding the button for two seconds will
volume. activate the CALL sound signal. The volume
of the sound signal (buzzer) can be adjusted
Special attention has been paid to the at the front panel.
intelligibility of speech. By applying low
noise/high speed opamps, a speech
presence filter and a specially developed
amplifier, communication is very comfortable
even in environments with a very high
background noise level.

2.0 UNPACKING

The shipping carton contains the parts listed ASL has taken great care to ensure this
below: product reaches you in flawless condition.
After unpacking the unit please inspect for
* The BS 15 any physical damage to the unit, and retain
* User manual the shipping carton and relevant packing
materials for use should the unit need
If any are missing, contact your dealer. returning.

If any damage has occurred, please notify
your dealer immediately so that a written
claim can be initiated. Please also refer to the
guarantee section of this manual.

3.0 INSTALLATION

This BS 15 will form part of an existing or connector, also on the rear panel.
new intercom system, and connection to it is The BS 15 is fully protected against mis-
straightforward. There are no separate power wiring (reverse power) or short-circuit in the
connections, or batteries to install, as the interconnecting cables.
necessary DC voltages are derived from the
intercom master station or power supply, via
the intercom connection cable.

To connect the BS 15 onto the intercom
system, use professional flexible microphone
cable with 2 wires and 1 shield only. Connect
the system intercom cable into the LINE
connector socket on the rear panel. Finally
connect the headset plug into the headset

User Manual BS 15 / Issue 2010 ASL Intercom, The Netherlands | 3

4.0 FRONT PANEL CONTROLS

1 VOLUME control knob
This knob adjusts the listen level for the
headset.

2 TALK button
This push button activates the headset
microphone, the large green LED indicates
if the microphone is switched on.

3 CALL button
This push button activates the call system.
A momentary push will send a call signal
to all stations connected to the intercom
channel and the call LEDS will start
flashing.
Press and hold the button for 2 seconds
will activate the call buzzer. 5 BUZZER VOLUME trimmer
After the CALL button is released the This trimmer adjusts the volume of the
LEDS will continue to flash for further 2 internal buzzer, which is located behind
seconds. the front panel.
The buzzer is activated if you press the
4 SIDETONE trimmer CALL button of the BS 15 (3) or a CALL
This trimmer adjusts the level of your own button of any other station (on the channel
voice as you hear it in your headset. to which the BS 15 is connected), longer
than 2 seconds.
Adjustment procedure :
- set trimmer in start position : fully
clockwise.
- switch off the microphone of all
connected (speaker!) stations.
- switch on the microphone of the BS 15.
- turn up volume.
- speak into the headset microphone.
- adjust the listen level by turning the
sidetone trimmer.

The operating area is between fully
clockwise and minimum level. Adjusting
the sidetone does not affect the level of
your voice as it is heard by other stations.


5.0 REAR PANEL CONNECTORS

6 LINE connectors
These XLR-3 connectors are for
connecting the BS 15 to the intercom
system.

Pin assignments:
1. 0 V / ground shield
2. +30 V power wire
3. audio wire

The female connector is for input.
The male connector is for extending the
intercom line to other user stations.

7 HEADSET connector
An XLR-4 type connector for the
connection of the local headset. This must
have a can impedance of 200 ohms (or
greater), or each minimum 400 ohms when
in parallel. The mic may be of the dynamic
or electret type.

Pin assignments:
1. Shield mic. (GND)
2. mic. +
3. phones +
4. phones - (GND)

6.0 INTERNAL CONTROLS

MIC GAIN
The mic gain can be adjusted internally by
a trimmer.

- Open the BS 15 by removing the four
screws on the underside.

- The trimmer is located on the lower PCB
board.

To increase mic gain turn clockwise.
To decrease mic gain turn
counterclockwise.


7.0 CABLING

For the BASIC Series Intercom system the Since the audio signal is transferred in an
interconnecting cables are of the shielded two- unbalanced * way, certain rules have to be
conductor microphone cable type and the obeyed when installing the cables of an intercom
intercom line connectors are of the XLR-3 type. network. This is to avoid earth loops and to
Audio and Call signals are on XLR pin 3, DC minimize power loss and the possible effect of
power is on XLR pin 2. XLR pin 1 is connected to electromagnetic fields.
the shield of the cable which functions as the
common return for audio and power. * See Party Line, Technical Concept

These rules are:
Use high quality (multipair) cable. Keep cables parallel as much as possible.
For interconnecting user stations, power When two (two channel) units in a network are
supplies and accessories in an ASL Intercom connected by more than one cable, make sure
network, use high quality shielded two-conduc- that these cables are parallel to each other
tor (minimum 2x 0.30 mm2) microphone cable over the whole distance between those units.
only. In case of a two channel intercom When using multipair cable, parallelism is
network, use high quality microphone ensured in the best possible way.
'multipair' cable only, each pair consisting of
two conductors (minimum 2x 0.15 mm2) with Avoid closed loops.
separate shield. Multipair cable should also Always avoid that cables are making a loop.
have an overall shield. So-called 'ring intercom' should not physically
be cabled as a ring. All cable routes should
Use flexible cables. have a 'star' configuration, with the central
Use flexible single and multipair microphone earthing point (usually close to the power
cable instead of cable with solid cores, supply position) as the centre of the star.
especially when the cable is subjected to
bending during operation or installation. Keep cables away from electromagnetic
sources.
Separate cable screen to XLR pin 1. Keep intercom cables away from high energy
The screen of each separate microphone cables, e.g. 115/230/400V mains power or
cable and/or the screen of each single pair in a dimmer controlled feeds for spotlights.
multipair cable, should be connected to pin 1 Intercom cables should cross high energy
of each XLR-3 connector. Do not connect this cables at an angle of 90° only.
cable screen to the metal housing of the Intercom cables should never be in the same
connector or to metal wall boxes (outlets). trunking as energy cables.
See page 10 for Earthing Concept.
Place power supply in a central position.
Cable trunks, connection boxes and In order to avoid unacceptable power losses,
overall multipair cable screen to clean place the power supply as close as possible to
earth. where most power consumption occurs or, in
Metal cable trunks, metal connection boxes other words, most user stations are placed.
and overall multipair cable screen should be
interconnected and, at one point (the 'central Connect ASL power supply to a 'clean'
earthing point') in the intercom network only, mains outlet.
be connected to a clean earth or a safety The ASL power supply may be connected to
earth. See page 10 for Earthing Concept. the mains power outlet to which other audio
equipment is connected. Avoid using mains
Keep metal connection boxes and cable outlets which also power dimmer controlled
housings isolated from other metal parts. lighting systems.
Metal housings for intercom cables and
connectors should be mounted in such a way In case of more complex installations, don't
that they are isolated from other metal cable hesitate to contact us. Please send us a block
and connector housings and from any other diagram of the planned network with a list of all
metal construction parts. user stations and their positions, and we are
happy to advise you on cabling lay out.


8.0 PARTY LINE, TECHNICAL CONCEPT

ASL's BASIC Series offers a complete two way further amplified and sent to the headphones.
('full duplex') communications system. This principle has three advantages:
Users of the system are connected via a 'party - the use of a single audio line allows several
line'. Master stations (with built-in power stations to talk and listen simultaneously.
supply), beltpacks and power supplies are - due to the high bridging impedance offered
interconnected via standard microphone cable. by each station, the number of stations 'on
One wire is used as an audio line, one as a line' has no influence on the level of the
power line and the screen of the cable communications signal.
functions as earth/return. - power and audio to the intercom stations
use the same cable.
Current drive is used for signal transfer. Each
station utilizes a current amplifier to amplify the The Call signal is also sent as a current on the
microphone signal and place it on the common audio line. It develops a DC potential over the
audio line where, due to the constant line line impedance which will be sensed by each
impedance (situated in the power supply station and interpreted as a Call signal.
between XLR pin 3 and 1), a signal voltage is
developed which can be

9.0 WARRANTY

This unit is warranted by ASL Intercom to the modifications or accidents are not covered by
original end-user purchaser against defects in this warranty. If the unit is faulty it should be
workmanship and materials in it's manufacture sent in it's original packing, to the supplier or
for a period of one year from date of shipment your local ASL dealer, with shipping prepaid. A
to the end-user. note must be included stating the faults found
Faults arising from misuse, unauthorized and a copy of the original suppliers invoice.

10.0 TECHNICAL SPECIFICATIONS

POWER CONSUMPTION BUZZER
(at 30 V DC) 18 mA quiescent max. SPL 100 dBA
35 mA signaling
80 mA at max. output + signaling DIMENSIONS AND WEIGHT
width 90 mm
MIC. PREAMP height 38 mm
mic. impedance 200 ohms depth 124 mm
gain 40 dB - 60 dB (adjustable internally) weight 260 grams
presence filter +6 dB at 5 kHz
frequency response 200 Hz - 15 kHz (-3 dB) GENERAL SYSTEM SPECIFICATIONS
V electret mic +9 V DC intercom line impedance 350 ohms (1kHz)
2.2 Kohms (DC)
HEADPHONES DRIVER AMP intercom line audio level nom. -18 dBu
max. load 200 ohms max. +4 dBu
max. output level 10.6 V rms (200 ohms) dynamic range 80 dB(1 kHz, THD<1%)
max. output power 0.5 W rms (200 ohms) call send signal +2.8 mA
call receive signal threshold +2.4 V DC
INTERCOM LINE DRIVER supply voltage +30 V DC (12 V to 32 V)
max. output current3 mA rms
output impedance > 150 Kohms Note : 0dBu defined as 775 mV into open circuit

SIDETONE ASL reserves the right to alter specifications without
rejection 0 - 30dB adjustable further notice


.


DESIGNED & MANUFACTURED BY:
ASL Intercom B.V.
Zonnebaan 42
3542 EG Utrecht
The Netherlands
Tel: +31 (0)30 2411901
Fax: +31 (0)30 2667373
Email: info@asl-inter.com
Web: www.asl-inter.com

ASL Intercom BS15

More Related Content

Similar to ASL Intercom BS15 (20)

More from AV ProfShop (20)

Recently uploaded (20)

ASL Intercom BS15