Ch28 ssm

Chapter 28
Magnetic Induction
Conceptual Problems
1 • (a) The magnetic equator is a line on the surface of Earth on
which Earth’s magnetic field is horizontal. At the magnetic equator, how
would you orient a flat sheet of paper so as to create the maximum
magnitude of magnetic flux through it? (b) How about the minimum
magnitude of magnetic flux?
Determine the Concept The magnetic flux will be a maximum when the normal
to the sheet is parallel to the magnetic field. The magnetic flux will be a minimum
when the normal to the sheet is perpendicular to the magnetic field.
(a) Orient the sheet so the normal to the sheet is both horizontal and
perpendicular to the local tangent to the magnetic equator.
(b) Orient the sheet of paper so the normal to the sheet is perpendicular to the
direction of the normal described in the answer to Part (a).
3 • Show that the following combination of SI units is equivalent to
the volt: T⋅m2
s .
Determine the Concept Because a volt is a joule per coulomb, we can show that
the SI units
s
mT 2
⋅
are equivalent to a volt by making a series of substitutions and
simplifications that reduces these units to a joule per coulomb.
The units of a tesla are
mA
N
⋅
:
s
A
mN
s
m
mA
N
s
mT
2
2
⋅
=
⋅
⋅=
⋅
Substitute the units of an ampere
(C/s), replace with J, and
simplify to obtain:
mN ⋅
C
J
s
s
C
J
s
mT 2
==
⋅
Finally, because a joule per coulomb
is a volt:
V
s
mT 2
=
⋅
5 • A current is induced in a conducting loop that lies in a horizontal plane
and the induced current is clockwise when viewed from above. Which of the
following statements could be true? (a) A constant magnetic field is directed
vertically downward. (b) A constant magnetic field is directed vertically upward.
151

Chapter 28152
(c) A magnetic field whose magnitude is increasing is directed vertically
downward. (d) A magnetic field whose magnitude is decreasing is directed
vertically downward. (e) A magnetic field whose magnitude is decreasing is
directed vertically upward.
Determine the Concept We know that the magnetic flux (in this case the
magnetic field because the area of the conducting loop is constant and its
orientation is fixed) must be changing so the only issues are whether the field is
increasing or decreasing and in which direction. Because the direction of the
magnetic field associated with the clockwise current is vertically downward, the
changing field that is responsible for it must be either increasing vertically upward
(not included in the list of possible answers) or a decreasing field directed into the
page. )(d is correct.
7 • The planes of the two circular loops in Figure 28-38, are parallel. As
viewed from the left, a counterclockwise current exists in loop A. If the
magnitude of the current in loop A is increasing, what is the direction of the
current induced in loop B? Do the loops attract or repel each other? Explain your
answer.
Determine the Concept Clockwise as viewed from the left. The loops repel each
other.
15 • True or false:
(a) The induced emf in a circuit is equal to the negative of the magnetic flux
through the circuit.
(b) There can be a non-zero induced emf at an instant when the flux through the
circuit is equal to zero.
(c) The self inductance of a solenoid is proportional to the rate of change of the
current in the solenoid.
(d) The magnetic energy density at some point in space is proportional to the
square of the magnitude of the magnetic field at that point.
(e) The inductance of a solenoid is proportional to the current in it.
(a) False. The induced emf in a circuit is equal to the rate of change of the
magnetic flux through the circuit.
(b) True. The rate of change of the magnetic flux can be non-zero when the flux
through the circuit is momentarily zero
(c) False. The self inductance of a solenoid is determined by its length, cross-
sectional area, number of turns per unit length, and the permeability of the matter
in its core.

Magnetic Induction 153
(d) True. The magnetic energy density at some point in space is given by
Equation 28-20:
0
2
m
2μ
B
u = .
(e) False. The inductance of a solenoid is determined by its length, cross-sectional
area, number of turns per unit length, and the permeability of the matter in its
core.
Magnetic Flux
21 • A circular coil has 25 turns and a radius of 5.0 cm. It is at the equator,
where Earth’s magnetic field is 0.70 G, north. The axis of the coil is the line that
passes through the center of the coil and is perpendicular to the plane of the coil.
Find the magnetic flux through the coil when the axis of the coil is (a) vertical,
(b) horizontal with the axis pointing north, (c) horizontal with the axis pointing
east, and (d) horizontal with the axis making an angle of 30º with north.
Picture the Problem Because the coil defines a plane with area A and B
r
is
constant in magnitude and direction over the surface and makes an angle θ with
the unit normal vector, we can use θφ cosm NBA= to find the magnetic flux
through the coil.
The magnetic flux through the
coil is given by:
θπθφ coscos 2
m rNBNBA ==
Substitute for numerical values to obtain:
( ) ( ) θμθπφ cosWb7.13cosm105.0
G10
T1
G70.025
22
4m =×⎟⎟
⎠
⎞
⎜⎜
⎝
⎛
⋅= −
(a) When the plane of the coil is
horizontal, θ = 90°:
( ) 090cosWb7.13m =°= μφ
(b) When the plane of the coil is
vertical with its axis pointing
north, θ = 0°:
( ) Wb140cosWb7.13m μμφ =°=
(c) When the plane of the coil is
vertical with its axis pointing
east, θ = 90°:
( ) 090cosWb7.13m =°= μφ

Chapter 28154
(d) When the plane of the coil is
vertical with its axis making an angle
of 30° with north, θ = 30°:
( ) Wb1230cosWb7.13m μμφ =°=
27 •• A long solenoid has n turns per unit length, has a radius R1, and carries
a current I. A circular coil with radius R2 and with N total turns is coaxial with the
solenoid and equidistant from its ends. (a) Find the magnetic flux through the coil
if R2 > R1. (b) Find the magnetic flux through the coil if R2 < R1.
Picture the Problem The magnetic field outside the solenoid is, to a good
approximation, zero. Hence, the flux through the coil is the flux in the core of the
solenoid. The magnetic field inside the solenoid is uniform. Hence, the flux
through the circular coil is given by the same expression with R2 replacing R1:
(a) The flux through the large
circular loop outside the solenoid is
given by:
NBA=mφ
Substituting for B and A and
simplifying yields:
( )( ) 2
10
2
10m RnINRnIN πμπμφ ==
(b) The flux through the coil when
R2 < R1 is given by:
( )( ) 2
20
2
20m RnINRnIN πμπμφ ==
Induced EMF and Faraday’s Law
33 •• A 100-turn circular coil has a diameter of 2.00 cm, a resistance of
50.0 Ω, and the two ends of the coil are connected together. The plane of the coil
is perpendicular to a uniform magnetic field of magnitude 1.00 T. The direction of
the field is reversed. (a) Find the total charge that passes through a cross section
of the wire. If the reversal takes 0.100 s, find (b) the average current and (c) the
average emf during the reversal.
Picture the Problem We can use the definition of average current to express the
total charge passing through the coil as a function of Iav. Because the induced
current is proportional to the induced emf and the induced emf, in turn, is given
by Faraday’s law, we can express ΔQ as a function of the number of turns of the
coil, the magnetic field, the resistance of the coil, and the area of the coil.
Knowing the reversal time, we can find the average current from its definition and
the average emf from Ohm’s law.

(a) Express the total charge that
passes through the coil in terms
of the induced current:
tIQ Δ=Δ av (1)
Relate the induced current to the
induced emf: R
II
ε== av
Using Faraday’s law, express the
induced emf in terms of φm: tΔ
Δ
−= mφ
ε
Substitute in equation (1) and
simplify to obtain:
R
dNB
R
dNB
R
NBA
R
t
R
tt
R
Q
2
4
2
2
2
2
2
m
m
π
π
φ
φ
ε
=
⎟
⎠
⎞
⎜
⎝
⎛
==
=ΔΔ
Δ
=Δ=Δ
where d is the diameter of the coil.
Substitute numerical values and
evaluate ΔQ:
( )( ) ( )
( )
mC26.1mC257.1
Ω0.502
m0200.0T00.1100
Δ
2
==
=
π
Q
(b) Apply the definition of average
current to obtain:
mA12.6
mA12.57
s0.100
mC1.257
Δ
Δ
av
=
===
t
Q
I
(c) Using Ohm’s law, relate the
average emf in the coil to the
average current:
( )( )
mV628
Ω50.0mA12.57avav
=
== RIε
Motional EMF
41 •• In Figure 28-47, the rod has a mass m and a resistance R. The rails are
horizontal, frictionless and have negligible resistances. The distance between the
rails is l. An ideal battery that has an emf ε is connected between points a and b
so that the current in the rod is downward. The rod released from rest at t = 0.
(a) Derive an expression for the force on the rod as a function of the speed.

Chapter 28156
(b) Show that the speed of the rod approaches a terminal speed and find an
expression for the terminal speed. (c) What is the current when the rod is moving
at its terminal speed?
Picture the Problem (a) The net force acting on the rod is the magnetic force it
experiences as a consequence of carrying a current and being in a magnetic field.
The net emf that drives I in this circuit is the difference between the emf of the
battery and the emf induced in the rod as a result of its motion. Applying a right-
hand rule to the rod reveals that the direction of this magnetic force is to the right.
Hence the rod will accelerate to the right when it is released. (b) We can obtain
the equation of motion of the rod by applying Newton’s second law to relate its
acceleration to ε, B, I, R and . (c) Lettingl tvv = in the equation for the current in
the circuit will yield current when the rod is at its terminal speed.
(a) Express the magnetic force on the
current-carrying rod:
BIF l=m
The current in the rod is given by:
R
vB
I
l−
=
ε (1)
Substituting for I yields:
( )vB
R
B
B
R
vB
F l
l
l
l
−=⎟
⎠
⎞
⎜
⎝
⎛ −
= εε
m
(b) Letting the direction of motion of
the rod be the positive x direction,
apply to the rod:xx maF∑ =
( )
dt
dv
mvB
R
B
=− l
l
ε
Solving for dtdv yields:
( )vB
mR
B
dt
dv
l
l
−= ε
Note that as v increases,
0→− vBlε , 0→dtdv and the
rod approaches its terminal speed .
Set
tv
0=dtdv to obtain:
( ) 0t =− vB
mR
B
l
l
ε ⇒
lB
v
ε
=t
(c) Substitute for v in equation
(1) to obtain:
tv
0=
−
=
R
B
B
I l
l
ε
ε

45 • A 2.00-cm by 1.50-cm rectangular coil has 300 turns and rotates in a
region that has a magnetic field of 0.400 T. (a) What is the maximum emf
generated when the coil rotates at 60 rev/s? (b) What must its angular speed be to
generate a maximum emf of 110 V?
Picture the Problem We can use the relationship NBAfπε 2max = to relate the
maximum emf generated to the area of the coil, the number of turns of the coil,
the magnetic field in which the coil is rotating, and the angular speed at which it
rotates.
(a) Relate the induced emf to the
magnetic field in which the coil
is rotating:
NBAfNBA πωε 2max == (1)
Substitute numerical values and evaluate εmax:
( )( )( )( )( ) V14s60m1050.1m1000.2T400.03002 122
max =××= −−−
πε
(b) Solve equation (1) for f:
NBA
f
π
ε
2
max
=
Substitute numerical values and evaluate f:
( )( )( )( ) rev/s486
m1050.1m1000.2T400.03002
V110
22
=
××
= −−
π
f
Inductance
49 •• An insulated wire that has a resistance of 18.0 Ω/m and a length of
9.00 m will be used to construct a resistor. First, the wire is bent in half and then
the doubled wire is wound on a cylindrical form ( Figure 28-50) to create a
25.0-cm-long helix that has a diameter equal to 2.00 cm. Find both the resistance
and the inductance of this wire-wound resistor.
Picture the Problem Note that the current in the two parts of the wire is in
opposite directions. Consequently, the total flux in the coil is zero. We can find
the resistance of the wire-wound resistor from the length of wire used and the
resistance per unit length.
Because the total flux in the coil is
zero:
0=L

Chapter 28158
Express the total resistance of the
wire:
LR ⎟
⎠
⎞
⎜
⎝
⎛
=
m
Ω
0.18
evaluate R:
( ) Ω162m00.9
m
Ω
0.18 =⎟
⎠
⎞
⎜
⎝
⎛
=R
53 ••• Show that the inductance of a toroid of rectangular cross section, as
shown in Figure 28-52 is given by L =
μoN2
H ln b / a( )
2π
where N is the total
number of turns, a is the inside radius, b is the outside radius, and H is the height
of the toroid.
Picture the Problem We can use Ampere’s law to express the magnetic field
inside the rectangular toroid and the definition of magnetic flux to express φm
through the toroid. We can then use the definition of self-inductance of a solenoid
to express L.
Using the definition of the self-
inductance of a solenoid, express
L in terms of φm, N, and I:
I
N
L mφ
= (1)
Apply Ampere’s law to a closed path
of radius a < r < b:
C0
C
2 IrBd μπ ==⋅∫ l
rr
B
or, because IC = NI,
NIrB 02 μπ = ⇒
r
NI
B
π
μ
2
0
=
Express the flux in a strip of height
H and width dr :
BHdrd =mφ
Substituting for B yields:
dr
r
NIH
d
π
μ
φ
2
0
m =
Integrate dφm from r = a to r = b to
obtain: ⎟
⎠
⎞
⎜
⎝
⎛
== ∫ a
bNIH
r
drNIH b
a
ln
22
00
m
π
μ
π
μ
φ
Substitute for mφ in equation (1) and
simplify to obtain: ⎟
⎠
⎞
⎜
⎝
⎛
=
a
bHN
L ln
2
2
0
π
μ

Magnetic Energy
55 • In a plane electromagnetic wave, the magnitudes of the electric fields
and magnetic fields are related by E = cB, where 001 μ∈=c is the speed of
light. Show that when E = cB the electric and the magnetic energy densities are
equal.
Picture the Problem We can examine the ratio of um to uE with E = cB and
001 μ∈=c to show that the electric and magnetic energy densities are equal.
Express the ratio of the energy
density in the magnetic field to the
energy density in the electric field: 2
00
2
2
02
1
0
2
E
m 2
E
B
E
B
u
u
∈μ∈
μ
==
Because E = cB:
2
00
22
00
2
E
m 1
cBc
B
u
u
∈μ∈μ
==
Substituting for c2
and simplifying
yields:
1
00
00
E
m
==
∈μ
∈μ
u
u
⇒ Em uu =
RL Circuits
59 • A circuit consists of a coil that has a resistance equal to 8.00 Ω and a
self-inductance equal to 4.00 mH, an open switch and an ideal 100-V battery—all
connected in series. At t = 0 the switch is closed. Find the current and its rate of
change at times (a) t = 0, (b) t = 0.100 ms, (c) t = 0.500 ms, and (d) t = 1.00 ms.
Picture the Problem We can find the current using ( )τt
eII −
−= 1f where
If = ε0/R and τ = L/R and its rate of change by differentiating this expression with
respect to time.
Express the dependence of the
current on If and τ:
( )τt
eII −
−= 1f
Evaluating If and τ yields: A12.5
Ω8.00
V1000
f ===
R
I
ε
and
ms0.500
Ω8.00
mH4.00
===
R
L
τ

Chapter 28160
Substitute for If and τ to obtain: ( )( )ms500.0
1A5.12 t
eI −
−=
Express dI/dt: ( )( )( )
( ) ms500.0
1ms500.0
kA/s0.25
s2000A5.12
t
t
e
e
dt
dI
−
−−
=
−−=
(a) Evaluate I and dI/dt at t = 0: ( ) ( )( ) 01A5.120 0
=−= eI
and
( ) kA/s0.25kA/s0.25 0
0
==
=
e
dt
dI
t
(b) Evaluating I and dI/dt at
t = 0.100 ms yields:
( ) ( )( )
A27.2
1A5.12ms100.0 ms500.0ms100.0
=
−= −
eI
and
( )
kA/s5.20
kA/s0.25 ms500.0ms100.0
ms500.0
=
= −
=
e
dt
dI
t
(c) Evaluate I and dI/dt at
t = 0.500 ms to obtain:
( ) ( )( )
A90.7
1A5.12ms500.0 ms500.0ms500.0
=
−= −
eI
and
( )
kA/s20.9
kA/s0.25 ms500.0ms500.0
ms500.0
=
= −
=
e
dt
dI
t
(d) Evaluating I and dI/dt at
t = 1.00 ms yields:
( ) ( )( )
A8.10
1A5.12ms00.1 ms500.0ms00.1
=
−= −
eI
and
( )
kA/s38.3
kA/s0.25 ms500.0ms00.1
ms00.1
=
= −
=
e
dt
dI
t
61 •• In the circuit shown in Figure 28-54, let ε0 = 12.0 V, R = 3.00 Ω, and
L = 0.600 H. The switch, which was initially open, is closed at time t = 0. At time
t = 0.500 s, find (a) the rate at which the battery supplies energy, (b) the rate of

Joule heating in the resistor, and (c) the rate at which energy is being stored in the
inductor.
Picture the Problem We can find the current using ( ),1f
τt
eII −
−= where
If = ε0/R,and τ = L/R, and its rate of change by differentiating this expression with
respect to time.
Express the dependence of the
current on If and τ :
( ) ( )τt
eItI −
−= 1f
Evaluating If and τ yields: A4.00
Ω3.00
V0.210
f ===
R
I
ε
and
s0.200
Ω3.00
H600.0
===
R
L
τ
Substitute for If and τ to obtain: ( ) ( )( )s200.0
1A00.4 t
etI −
−=
Express dI/dt: ( )( )( )
( ) s200.0
1s200.0
A/s0.20
s00.5A00.4
t
t
e
e
dt
dI
−
−−
=
−−=
(a) The rate at which the battery
supplies energy is given by:
0εIP =
Substituting for I and ε0 yields: ( ) ( )( )( )
( )( )s200.0
s200.0
1W0.48
V0.121A00.4
t
t
e
etP
−
−
−=
−=
The rate at which the battery
supplies energy at t = 0.500 s is:
( ) ( )( )
W1.44
1W0.48s500.0 s200.0500.0
=
−= −
eP
(b) The rate of Joule heating is: RIP 2
J =
Substitute for I and R and simplify to
obtain:
( )( )[ ] ( )
( )( )2s200.0
2s200.0
J
1W8.04
Ω00.31A00.4
t
t
e
eP
−
−
−=
−=
The rate of Joule heating at
t = 0.500 s is:
( ) ( )( )
W4.40
1W8.04s500.0
2s200.0s500.0
J
=
−= −
eP

Chapter 28162
(c) Use the expression for the
magnetic energy stored in an
inductor to express the rate at which
energy is being stored:
[ ] dt
dI
LILI
dt
d
dt
dU
== 2
2
1L
Substitute for L, I, and dI/dt to obtain:
( )( )( )( )
( )( ) s200.0s200.0
s200.0s200.0L
1W0.48
A/s0.201A00.4H600.0
tt
tt
ee
ee
dt
dU
−−
−−
−=
−=
Evaluate this expression for t = 0.500 s:
( )( ) W62.31W0.48 s200.0s500.0s200.0s500.0
s500.0
L
=−=⎥
⎦
⎤ −−
=
ee
dt
dU
t
Remarks: Note that, to a good approximation, dUL/dt = P − PJ.
63 •• A circuit consists of a 4.00-mH coil, a 150-Ω resistor, a 12.0-V ideal
battery and an open switch—all connected in series. After the switch is closed:
(a) What is the initial rate of increase of the current? (b) What is the rate of
increase of the current when the current is equal to half its steady-state value?
(c) What is the steady-state value of the current? (d) How long does it take for the
current to reach 99 percent of its steady state value?
Picture the Problem If the current is initially zero in an LR circuit, its value at
some later time t is given by ( )τt
eII −
−= 1f , where If = ε0/R and τ = L/R is the
time constant for the circuit. We can find the rate of increase of the current by
differentiating I with respect to time and the time for the current to reach any
given fraction of its initial value by solving for t.
(a) Express the current in the circuit
as a function of time:
( )τε t
e
R
I −
−= 10
Express the initial rate of increase of
the current by differentiating this
expression with respect to time:
( )
( )
t
L
R
t
L
R
t
t
e
L
e
R
e
R
e
dt
d
Rdt
dI
−
−
−
−
=
=⎟
⎠
⎞
⎜
⎝
⎛
−−=
−=
0
00
0
1
1
ε
εε
ε
ττ
τ
τ

Evaluate dI/dt at t = 0 to obtain:
kA/s3.00
mH4.00
V12.000
0
===
=
e
Ldt
dI
t
ε
(b) When I = 0.5If: τt
e−
−=15.0 ⇒ 5.0=− τt
e
Evaluate dI/dt with 5.0=− τt
e to
obtain:
kA/s1.50
mH4.00
V12.0
5.05.0 0
5.0
=
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛
==
=− Ldt
dI
t
e
ε
τ
(c) Calculate If from ε0 and R: mA80.0
Ω150
V12.00
f ===
R
I
ε
(d) When I = 0.99If: τt
e−
−= 199.0 ⇒ 01.0=− τt
e
Solving for t and substituting for τ
yields:
( ) ( )01.0ln01.0ln
R
L
t −=−= τ
evaluate t:
( ) ms123.001.0ln
Ω150
mH4.00
=−=t
65 •• Given the circuit shown in Figure 28-55, assume that the inductor has
negligible internal resistance and that the switch S has been closed for a long time
so that a steady current exists in the inductor. (a) Find the battery current, the
current in the 100 Ω resistor, and the current in the inductor. (b) Find the potential
drop across the inductor immediately after the switch S is opened. (c) Using a
spreadsheet program, make graphs of the current in the inductor and the potential
drop across the inductor as functions of time for the period during which the
switch is open.
Picture the Problem The self-induced emf in the inductor is proportional to the
rate at which the current through it is changing. Under steady-state conditions,
dI/dt = 0 and so the self-induced emf in the inductor is zero. We can use
Kirchhoff’s loop rule to obtain the current through and the voltage across the
inductor as a function of time.

Chapter 28164
(a) Because, under steady-state
conditions, the self-induced emf in
the inductor is zero and because the
inductor has negligible resistance,
we can apply Kirchhoff’s loop rule
to the loop that includes the source,
the 10-Ω resistor, and the 2-H
inductor to find the current drawn
from the battery and flowing through
the inductor and the 10-Ω resistor:
( ) 010V10 10 =Ω− Ω−I
Solving for yields:Ω−10I A0.1H210 == −Ω− II
By applying Kirchhoff’s junction
rule at the junction between the
resistors, we can conclude that:
0H-2battery-100 =−=Ω III
(b) When the switch is opened, the current cannot immediately go to zero in the
circuit because of the inductor. For a time, a current will circulate in the circuit
loop between the inductor and the 100-Ω resistor. Because the current flowing
through this circuit is initially 1 A, the voltage drop across the 100-Ω resistor is
initially V.100 Conservation of energy (Kirchhoff’s loop rule) requires that the
voltage drop across the 2-H inductor is V.100H-2 =V
(c) Apply Kirchhoff’s loop rule to
the RL circuit to obtain:
0=+ IR
dt
dI
L
The solution to this differential
equation is:
( ) τ
t
t
L
R
eIeItI
−−
== 00
where s020.0
100
H0.2
=
Ω
==
R
L
τ

A spreadsheet program to generate the data for graphs of the current and the
voltage across the inductor as functions of time is shown below. The formulas
used to calculate the quantities in the columns are as follows:
Cell Formula/Content Algebraic Form
B1 2.0 L
B2 100 R
B3 1 I0
A6 0 t0
B6 $B$3*EXP((−$B$2/$B$1)*A6) t
L
R
eI
−
0
A B C
1 L= 2 H
2 R= 100 ohms
3 I0= 1 A
4
5 t I(t) V(t)
6 0.000 1.00E+00 100.00
7 0.005 7.79E−01 77.88
8 0.010 6.07E−01 60.65
9 0.015 4.72E−01 47.24
10 0.020 3.68E−01 36.79
11 0.025 2.87E−01 28.65
12 0.030 2.23E−01 22.31
32 0.130 1.50E−03 0.15
33 0.135 1.17E−03 0.12
34 0.140 9.12E−04 0.09
35 0.145 7.10E−04 0.07
36 0.150 5.53E−04 0.06

Chapter 28166
The following graph of the current in the inductor as a function of time was
plotted using the data in columns A and B of the spreadsheet program.
0.0
0.2
0.4
0.6
0.8
1.0
0.00 0.03 0.06 0.09 0.12 0.15
t (s)
I(A)
The following graph of the voltage across the inductor as a function of time was
plotted using the data in columns A and C of the spreadsheet program.
0
20
40
60
80
100
0.00 0.03 0.06 0.09 0.12 0.15
t (s)
V(V)
69 ••• In the circuit shown in Figure 28-54, let ε0 = 12.0 V, R = 3.00 Ω, and
L = 0.600 H. The switch is closed at time t = 0. During the time from t = 0 to
t = L/R, find (a) the amount of energy supplied by the battery, (b) the amount of
energy dissipated in the resistor, and (c) the amount of energy delivered to the
inductor. Hint: Find the energy transfer rates as functions of time and integrate.
Picture the Problem We can integrate I,dtdE 0ε= where ( )τt
eII −
−= 1f , to
find the energy supplied by the battery, RIdtdE 2
J = to find the energy
dissipated in the resistor, and ( ) ( )( )2
2
1
ττ ILUL = to express the energy that has
been stored in the inductor when t = L/R.

(a) Express the rate at which energy
is supplied by the battery:
I
dt
dE
0ε=
Express the current in the circuit as a
function of time:
( )τε t
e
R
I −
−= 10
Substitute for I to obtain:
( )τε t
e
Rdt
dE −
−= 1
2
0
Separate variables and integrate
from t = 0 to t = τ to obtain:
( )
( )[ ]
eR
L
eR
e
R
dte
R
E t
2
2
0
2
0
1
2
0
0
2
0
1
εε
ε
ε
τ
τττ
τ
τ
==
+−−=
−=
−
−
∫
evaluate E:
( ) ( )
( )
J53.3
Ω00.3
H600.0V0.12
2
2
==
e
E
(b) Express the rate at which energy
is being dissipated in the resistor: ( )
( )ττ
τ
ε
ε
tt
t
ee
R
Re
R
RI
dt
dE
2
2
0
2
02J
21
1
−−
−
+−=
⎥⎦
⎤
⎢⎣
⎡
−==
Separate variables and integrate
from t = 0 to t = L/R to obtain:
( )
⎟
⎠
⎞
⎜
⎝
⎛
−−=
⎟
⎟
⎟
⎟
⎠
⎞
⎜
⎜
⎜
⎜
⎝
⎛
−−=
+−= ∫
−−
22
2
0
2
2
0
0
2
2
0
J
2
1
2
12
22
2
21
eeR
L
e
R
L
R
L
e
R
L
R
dtee
R
E
RL
tt
ε
ε
ε ττ
evaluate EJ:
( ) ( )
( )
J61.1
2
1
2
12
Ω3.00
H0.600V12.0
22
2
J
=
⎟
⎠
⎞
⎜
⎝
⎛
−−=
ee
E

Chapter 28168
(c) Express the energy stored in the
inductor when t =
R
L
:
( )
( )21
2
2
0
2
10
2
1
2
1
1
2
1
−
−
−=
⎟
⎠
⎞
⎜
⎝
⎛
−=
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛
⎟
⎠
⎞
⎜
⎝
⎛
=⎟
⎠
⎞
⎜
⎝
⎛
e
R
L
e
R
L
R
L
IL
R
L
UL
ε
ε
evaluate UL:
( )( )
( )
( )
J92.1
1
Ω3.002
V12.0H0.600 21
2
2
=
−=⎟
⎠
⎞
⎜
⎝
⎛ −
e
R
L
UL
Remarks: Note that, as we would expect from energy conservation,
E = EJ + EL.
General Problems
71 •• Figure 28-59 shows a schematic drawing of an ac generator. The basic
generator consists of a rectangular loop of dimensions a and b and has N turns
connected to slip rings. The loop rotates (driven by a gasoline engine) at an
angular speed of ω in a uniform magnetic field
r
B. (a) Show that the induced
potential difference between the two slip rings is given by ε = NBabω sin ωt.
(b) If a = 2.00 cm, b = 4.00 cm, N = 250, and B = 0.200 T, at what angular
frequency ω must the coil rotate to generate an emf whose maximum value is
100V?
Picture the Problem (a) We can apply Faraday’s law and the definition of
magnetic flux to derive an expression for the induced emf in the coil (potential
difference between the slip rings). In Part (b) we can solve the equation derived in
Part (a) for ω and evaluate this expression under the given conditions.
(a) Use Faraday’s law to express the
induced emf:
( )
dt
td mφ
ε −=
Using the definition of magnetic
flux, relate the magnetic flux through
the loop to its angular velocity:
( ) tNBAt ωφ cosm =

Substitute for ( )tmφ to obtain:
[ ]
( )
tNBab
tNBab
tNBA
dt
d
ωω
ωω
ωε
sin
sin
cos
=
−−=
−=
(b) Express the condition under
which ε = εmax:
1sin =tω
and
ωε NBab=max ⇒
NBab
maxεω =
Substitute numerical values and evaluate ω:
( )( )( )( )
krad/s2.50
m0.0400m0.0200T0.200250
V100
==ω
77 •• Figure 28-60a shows an experiment designed to measure the
acceleration due to gravity. A large plastic tube is encircled by a wire, which is
arranged in single loops separated by a distance of 10 cm. A strong magnet is
dropped through the top of the loop. As the magnet falls through each loop the
voltage rises and then the voltage rapidly falls through zero to a large negative
value and then returns to zero. The shape of the voltage signal is shown in Figure
28-62b. (a) Explain the basic physics behind the generation of this voltage pulse.
(b) Explain why the tube cannot be made of a conductive material.
(c) Qualitatively explain the shape of the voltage signal in Figure 28-60b. (d) The
times at which the voltage crosses zero as the magnet falls through each loop in
succession are given in the table in the next column. Use these data to calculate a
value for g.
Picture the Problem
(a) As the magnet passes through a loop it induces an emf because of the
changing flux through the loop. This allows the coil to ″sense″ when the magnet
is passing through it.
(b) One cannot use a cylinder made of conductive material because eddy currents
induced in it by a falling magnet would slow the magnet.
(c) As the magnet approaches the loop the flux increases, resulting in the negative
voltage signal of increasing magnitude. When the magnet is passing a loop, the
flux reaches a maximum value and then decreases, so the induced emf becomes
zero and then positive. The instant at which the induced emf is zero is the instant
at which the magnet is at the center of the loop.

Chapter 28170
(d) Each time represents a point when the distance has increased by 10 cm. The
following graph of distance versus time was plotted using a spreadsheet program.
The regression curve, obtained using Excel’s ″Add Trendline″ feature, is shown
as a dashed line.
y = 4.9257t 2
+ 1.3931t + 0.0883
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40
t (s)
y(m)
The coefficient of the second-degree term is .2
1
g Consequently,
( ) 22
m/s85.9m/s9257.42 ==g
79 •• A long solenoid has n turns per unit length and carries a current that
varies with time according to I = I0 sin ωt. The solenoid has a circular cross
section of radius R. Find the induced electric field, at points near the plane
equidistant from the ends of the solenoid, as a function of both the time t and the
perpendicular distance r from the axis of the solenoid for (a) r < R and (b) r > R.
Picture the Problem We can apply Faraday’s law to relate the induced electric
field E to the rates at which the magnetic flux is changing at distances r < R and
r > R from the axis of the solenoid.
(a) Apply Faraday’s law to relate the
induced electric field to the magnetic
flux in the solenoid within a
cylindrical region of radius r < R:
dt
d
d m
C
φ
−=⋅∫ l
rr
E
or
( )
dt
d
rE m
2
φ
π −= (1)
Express the field within the solenoid: nIB 0μ=

Express the magnetic flux through
an area for which r < R:
nIrBA 0
2
m μπφ ==
Substitute in equation (1) to obtain:
( ) [ ]
dt
dI
nr
nIr
dt
d
rE
0
2
0
2
2
μπ
μππ
−=
−=
Because tII ωsin0= :
[ ]
tnIr
tI
dt
d
nrE Rr
ωωμ
ωμ
cos
sin
002
1
002
1
−=
−=<
(b) Proceed as in (a) with r > R to
obtain:
( ) [ ]
tnIR
dt
dI
nR
nIR
dt
d
rE
ωωμπ
μπ
μππ
cos
2
00
2
0
2
0
2
−=
−=
−=
Solving for yields:RrE >
t
r
InR
E Rr ω
ωμ
cos
2
0
2
0
−=>

Ch28 ssm

More Related Content

What's hot (20)

Similar to Ch28 ssm (20)

More from Marta Díaz (20)

Recently uploaded (20)

Ch28 ssm