ComNet CLFE1UTP User Manual
0 likes434 views
The document is an installation and operation manual for Comnet's CLFE(X)UTP Ethernet-over-UTP extenders, supporting 100 Mbps Ethernet and pass-through PoE with four models available for various channel configurations. These extenders enable long-distance transmission (up to 3,000 feet) and are designed for easy installation with environmental hardening features. Important safety warnings and installation instructions are provided to ensure proper use and compliance with local codes.
ComNet CLFE1UTP User Manual
- 1. INS_CLFEXUTP_REV– 09/28/11 PAGE 1 INSTALLATION AND OPERATION MANUAL CLFE(X)UTP Ethernet-over-UTP/Twisted Pair Extender with Pass-Through PoE The ComNet™ CopperLine® CLFE(X)UTP Ethernet over UTP line consists of four models that support 100Mbps Ethernet as well as Pass-through Power over Ethernet (PoE) over twisted pair cable (CAT5, UTP). These models support transmission distances of up to 3,000 feet (914m) at 10 Mbps, or 2,100 feet (640m) at 100 Mbps. The CLFE1UTP, the CLFE4UTP, CLFE8UTP and the CLFE16UTP transport, one, four, eight or sixteen channels respectively. The IEEE 802.3-compliant Ethernet electrical interface of these Ethernet extenders also meets the requirements for IEEE 802.3af PoE power, passing-through up to 30 watts of power per port to the powered device (PD). The CLFE(X)UTP series may also be used interchangeably with other CopperLine Ethernet-over-UTP extenders. Environmentally hardened to the requirements of NEMA TS-1/ TS-2 for most out-of- plant applications, and true plug-and-play design ensures ease of installation and operation. LED indicators are provided for rapidly ascertaining the operating status of the device. See Figures 6 – 8 on Page 7 for LED explanations. Packaged in a rugged aluminum housing, these units are designed for desktop or stand- alone mounting. The CLFE8UTP and CLFE16UTP are offered in EIA 19” 1U high rack for easy installation. See Figures A through C on Page 8 for mounting instructions. See Figures 1 – 8 for complete installation details. Important Safety Warning: Read and keep these directions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Install in accordance with the manufacturer’s instructions This installation should be made by a qualified servicepersonandshouldconformtoalllocalcodes See further safety instructions on Page 8
- 2. INS_CLFEXUTP_REV– 09/28/11 PAGE 2 CAT5/6 UTP CAT5/6 or UTP CAT5/6 CAT5/6 FIGURE 1 – CLFE1UTP FIGURE 3 – CLFE4UTP FIGURE 2 – CLFE1UTP INSTALLATION AND OPERATION MANUAL CLFE(X)UTP RIGHT PANELLEFT PANEL LEFT PANEL RIGHT PANEL Tech Support: 1.888.678.9427 For 1-pair mode, use the first pair of pins (pins 1 & 2) of the “Extended Ethernet” RJ-45 port on the left panel. Note: 4-pair mode is required for PoE. * Warning: A ground connection is required for the surge protection to work. Failure to ground properly voids the warranty and may cause damage. * Warning: A ground connection is required for the surge protection to work. Failure to ground properly voids the warranty and may cause damage. 2 1 Ground Screw* Ground Screw* Power Supply Connection via external power adaptor Optional, if there is no power supply connected to the unit it will try to detect PoE. – + Note: Center pin on power connector is positive (+).
- 3. INS_CLFEXUTP_REV– 09/28/11 PAGE 3 INSTALLATION AND OPERATION MANUAL CLFE(X)UTP Tech Support: 1.888.678.9427 Pass-Through PoE Operations for the CLFE1UTP ComNet’s CopperLine CLFE1UTP extended distance IP data and PoE maintains the safety standards for communications found within the 802.3af PoE standards. This is for the protection of products operating in the extended distance transmission chain. In the event of malfunctions the communication system is designed to shut down power transmission to avoid device damage. The CLFE1UTP can be powered by a local power source (12 Volts D.C. or 24 Volts A.C.) or from a single PSE source, such as a network switch’s PoE port using its unique Pass-through PoE feature (4-pair mode only). This latter feature eliminates the need for CLFE1UTP local power while also providing power for the camera (See full installation instructions, Page 6). Powering The CLFE1UTP Transceivers Under normal operating conditions CLFE1UTP transceivers should be powered using the PoE source. External power to the CLFE1UTP should be restricted to installations where a camera requires local power. When installing the CLFE1UTP, the following conditions apply which will affect its operations. The CLFE1UTP is provided with the ability to operate using a local external power supply. The standard accessory local power adaptor plug can be used for power supplies that do not have the CLFE1UTP’s standard power input connector. When inserting the adaptor into the power input, the CLFE1UTP is only powered from a local power source and not from a PSE source. The camera will continue receiving power from the PSE source and operations will be normal. However, if the external plug adaptor is inserted in the CLFE1UTP and no power is applied, the CLFE1UTP will not power up even if a PoE source is present, the camera will continue to receive power. In this case the CLFE1UTP is not operational and no data will flow. If the CLFE1UTP is externally powered and PSE power is lost, power to the CLFE1UTP must be recycled in order for the PSE to recognize the PD (Camera). Input with external power plug installed. External power adapter (included)
- 4. INS_CLFEXUTP_REV– 09/28/11 PAGE 4 12V Power Supply Ground Screw* 12V Power Supply Ground Screw* FIGURE 4 – CLFE8UTP FIGURE 5 – CLFE16UTP INSTALLATION AND OPERATION MANUAL CLFE(X)UTP Tech Support: 1.888.678.9427 CAT5/6 or UTP CAT5/6 or UTP CAT5/6 or UTP CAT5/6 or UTP CAT5/6 or UTP CAT5/6 or UTP CAT5/6 CAT5/6 CAT5/6 CAT5/6 CAT5/6 CAT5/6 * Warning: A ground connection is required for the surge protection to work. Failure to ground properly voids the warranty and may cause damage. * Warning: A ground connection is required for the surge protection to work. Failure to ground properly voids the warranty and may cause damage.
- 5. INS_CLFEXUTP_REV– 09/28/11 PAGE 5 INSTALLATION AND OPERATION MANUAL CLFE(X)UTP Tech Support: 1.888.678.9427 FIGURE 6 – POSSIBLE ETHERNET CONFIGURATIONS Multiple Configurations are possible. Consult ComNet Design Center. ≤3,000ft (914m) Cat-5 OR ≤5,000ft (1524m) Coax CLFE16UTP CopperLine 4-Port Switch Extended over UTP or Coax NVR CLFE16UTP PoE Switch CNGE2FE24MSPOE ≤328ft (100m) Cat-5 CLFE4US1TPC IP Cameras IP Cameras ≤3,000ft (914m) Cat-5 ≤5,000ft (1524m) Coax CopperLine Managed High Power Midspan NVR CLFE16IPS Switch CNGE2FE24MS Data + Power Data +Power CLFE1UTP CLFE1UTP CLFE1UTP CLFE1UTP PoE Camera PoE Camera CLFE16UTP Single Port CopperLine over UTP NVR PoE Switch CNGE2FE24MSPOE ≤3,000ft (914m) Cat-5 ≤328ft (100m) Cat-5CLFE1UTP CLFE1UTP PoE Camera NVR Multi Port CopperLine over UTP PoE Switch CNGE2FE24MSPOE ≤3,000ft (914m) Cat-5 ≤328ft (100m) Cat-5CLFE1UTP PoE Camera
- 6. INS_CLFEXUTP_REV– 09/28/11 PAGE 6 INSTALLATION AND OPERATION MANUAL CLFE(X)UTP Tech Support: 1.888.678.9427 IP Camera-end Installation (CLFE1UTP) Set the S1 10/100BaseT dip switch to the appropriate rate based on the required maximum data rate and maximum distance. OFF = 10BaseT; ON = 100BaseT Set the S2 Master/Slave dip switch to ON for “Master” mode Set the S3 1- or 4-pair dip switch ON for 1-pair or OFF for 4-pair operation. For systems not utilizing PoE, connect the 12V Power Supply to the power connector of the CLFE1UTP. A power adapter connector is provided to simplify connection. CAUTION: If the external power adaptor is connected with no power applied, the CLFE1UTP will not recognize the PoE source and the system will be inoperative. Connect the IP camera RJ-45 connector to the 10/100BaseT Ethernet port of the CLFE1UTP using a standard Cat5/6 cable, 100m length (max). Connect one end of the long UTP cable to the RJ-45 connector of the CLFE1UTP. The link LED on the 10/100 connector should be “ON” to indicate proper connection between the camera and the CLFE1UTP. Ethernet Switch/NVR-end Installation (CLFE1UTP) Set the S2 Master/Slave dip switch to OFF for “Slave” mode Set the S1 and S3 dip switches to match the setting on the camera-end. CLFE4UTP, CLFE8UTP and CLFE16UTP: For each channel used, set the appropriate dip switches for each channel to match the camera end. Note:Multichannelunitsarepresetto “Slave”mode.Noadjustmentrequired. For systems not utilizing PoE, connect the 12V Power Supply to the power connector of the selected CLFE(X)UTP. Connect the RJ-45 connector of the Ethernet switch to the 10/100BaseT Ethernet port of the selected CLFE(X)UTP using a standard Cat5/6 cable, 100m length (max). Connect one end of the long UTP cable to the RJ-45 connector of the selected CLFE(X)UTP. The Link LED on the 10/100 Ethernet connector should be “ON” to indicate proper connection between the switch and the selected CLFE(X)UTP. The Link LED (Red for 100BaseT, Green for 10BaseT) will be “ON” and not flashing to indicate confirmed connection between the CLFE1UTP and selected CLFE(X)UTP extenders. On Off On Off S1 S2 S3 S4 S1 S2 S3 S4 1-p 4-P 10 100 S1 S2 S3S1 S2 S3
- 7. INS_CLFEXUTP_REV– 09/28/11 PAGE 7 INSTALLATION AND OPERATION MANUAL CLFE(X)UTP Tech Support: 1.888.678.9427 FIGURE 7 – POWER LED INDICATORS FIGURE 7 – EXTENDED LED INDICATORS FIGURE 8 – ETHERNET LED INDICATORS POWER RED Power is on OFF Power is off TRAFFIC (Extended) 10/100BaseT GREEN – Connection is OK, 10BaseT mode YELLOW Flashing,Traffic present – RED – Connection is OK, 100BaseT mode OFF No traffic – TRAFFIC (Standard) Link GREEN Flashing – Connection is OK with traffic – YELLOW – Connection is OK OFF No connection No connection
- 8. INS_CLFEXUTP_REV– 09/28/11 PAGE 8 MECHANICAL INSTALLATION INSTRUCTIONS CLFE(X)UTP Tech Support: 1.888.678.9427 Figure A Dimensions are for the CLFE1UTP standalone ComNet module Figure B Dimensions are for the CLFE4UTP standalone ComNet module Figure C Dimensions are for the CLFE8UTP and CLFE16UTP ComNet modules 3.73 (9.5cm) 3.6 (9.2cm) 17 (43.2cm) 1.6 (4cm) 3.3 (8.4cm) 1.6 (4cm) 1.75 (4.45cm) 3.25 (8.25cm) 1.6 (4cm) 1.15 (3cm) Installation Considerations The CLFE1UTP and CLFE4UTPare supplied as Standalone modules. The CLFE8UTP and CLFE16UTP can be installed as Standalone modules or can be rack-mounted with the addition of the provided 19-Inch Rack-Mounting Ear Brackets.
- 9. INS_CLFEXUTP_REV– 09/28/11 PAGE 9© 2012 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC. 3 Corporate Drive | Danbury, CT 06810 | USA T: 203.796.5300 | F: 203.796.5303 | Tech Support: 1.888.678.9427 | info@comnet.net 8 Turnberry Park Road | Gildersome | Morley | Leeds, UK LS27 7LE T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | info-Europe@comnet.net MECHANICAL INSTALLATION INSTRUCTIONS • Read and keep these directions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with a dry cloth. • Install in accordance with the manufacturer’s instructions. • This installation should be made by a qualified service person and should conform to all local codes. • DO NOT bundle UTP or Coax signals in the same conduit as high-voltage wiring. • To reduce the risk of fire or electrical shock, do not expose these products to rain, moisture, dripping or splashing. • No objects filled with liquids, such as vases, shall be placed on the equipment. • DO NOT install the unit in a place where the operating ambient temperature exceeds 75ºC. • Make sure that the external power supply output voltage is in the recommended range. • Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including DVRs) that produce heat. • Protect the power cord from being walked on or pinched, particularly at the power source, convenience receptacles and the point where they exit from the apparatus. • Only use attachments/accessories specified by the manufacturer. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when a power supply cord or plug is damaged, liquid has been spilled, objects have fallen inside the apparatus, the apparatus has been exposed to rain or moisture, do not operate normally or has been dropped. • The main plus is used as the disconnect device and shall remain readily operable. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. WARNING: This apparatus is a Class I product. This product must be connected to a mains socket outlet through an AC to DC power supply. WARNING: The mains plug is used as the disconnect device and shall remain readily operable. WARNING: For non-PoE applications, unit is to be connected to a mains socket outlet through a Listed Class I power supply rated 12 VDC or 24 VAC.