Combined report on NCES

A

Report

On

Non Conventional Energy Sources

By

Prashant Kumar

Submitted in partial fulfilment of requirement for award of

Degree of

Bachelor of engineering

In

Electrical engineering

From Rajasthan technical university

Submitted to,

Mr. Abhisekh Yadav

(Seminar In-charge, EE)

R.I.E.T, Jaipur

CERTIFICATE

This to certify that Mr. Prashant Kumar, Roll no.61, final year (viiith sem) student
of electrical engineering has delivered a seminar and submitted the report on Non
Conventional Energy Sources for the academic session 2009-2010.

Submitted to,

Mr. Abhisekh Yadav

(Seminar In-Charge, EE)

R.I.E.T. , Jaipur

ACKNOWLEDGEMENT

I have a great pleasure in submitting the report carried out in the Electrical Dept. of RIET,
Jaipur. The report is on Non Conventional Energy Sources.

I’m greatly indebted to Dr. Renu Joshi (Principal), Mrs. Ekta Sharma (HOD, EE)
and Mr. Abhisekkh Yadav (Seminar –Inchg.), without whom successful completion of
seminar was not possible.

I express my extreme regret to them that I could have forgotten to express my thanks to.

Prashant Kumar
Electrical Engg.
Viith - sem

Abstract

Energy is the primary and most universal measure of all kinds of work by
human beings and nature. Energy is also defined as the ability or the
capacity to do work. We use energy to do work and make all movements.
When we eat, our body transforms the food into energy to do work. When
we run or walk or do some work, we 'burn' energy in our bodies. Cars,
planes, trolleys, boats, and machinery also transform energy into work.
Work means moving or lifting something, warming or lighting
something. There are many sources of energy that help to run the various
machines invented by men. So, we can say that as the population and
requirement of any nation is increased the requirement of the energy
(demand) will also increase for satisfying all types of the loads i.e.
industrial, domestic etc. As the demand is going to increase the
generations have to be increased. So as the time is going to pass the
conventional energy sources are going to be decreased and it might
happen that after some years these sources are going to be exhausted. The
best alternative of conventional energy sources are the non-conventional
energy sources, which are never going to become exhausted because they
are the natural sources and they are permanently available for use.


INDEX

CONTENTS PAGE NO.

1. ENERGY SOURCES 2– 8

2. SOLAR ENERGY 9 – 17

3. WIND ENERGY 18 –20

4. BIO-ENERGY 21 – 29

5. TIDAL POWER PLANTS 30 – 34

6. FUEL CELLS 35– 38

7. REFRENCES 39

1


CHAPTER – 1 ENERGYSOURCES

1.1. Introduction to energy

The energy of a body is its capacity to do work. It is measured the total amount of
work that the body can do. Energy is the primary and most universal measure of all
kinds work by human beings and nature. Every thing what happens the world is the
expression of flow of energy in one of its forms.

1.2. Different forms of energy

The different forms of energy are:
1. Mechanical energy (kinetic and potential)
2. Thermal (or) Heat energy
3. Chemical energy
4. Electrical energy
5. Nuclear energy
6. Electromagnetic energy
7. Gravitational energy
The S.I unit of energy is Joule or KJ or Watt.h.

Primary Energy Sources

Primary energy sources can be defined as sources which provide a net supply of
energy Coal, Oil, Uranium etc., are examples of this type. The energy required to
obtain these fuels is much use than what they can produce by combustion or nuclear
reaction. The supply of primary fuels is limited. It becomes very essential to use these
fuels sparingly.
Examples
Coal, natural gas, oil and nuclear energy.

2


Secondary Energy sources

Secondary fuels produce no net energy. Though it may by necessary for the economy,
these may not yield net energy. Secondary sources are like sun, wind, water (tides),
etc. Solar energy can by used through plants, solar cells, solar heaters and solar
collectors.

1.3. Energy sources and their availability

Introduction

Today every country draws its energy needs from a variety of sources. We can
broadly categorize these sources as commercial and noncommercial. The commercial
sources include the fossil fuels (coal, oil and natural gas), hydro-electric power and
nuclear power, while the noncommercial sources include wood, animal waste and
agricultural wastes. Inane Industrialized country like U.S.A. most of the energy
requirements are met from commercial sources, while in an Industrially less
developed country like India, the use of commercial and non-commercial sources are
about equal.

1.4. Conventional and non-conventional sources energy

1.4.1. Conventional energy sources

Conventional energy sources are:

(a) Fossil fuel energy
(b) Hydraulic energy
(c) Nuclear energy

3


(a) Fossil fuel energy

Coal, petroleum, and natural gas are called Fossil fuel as these are formed by the
decomposition of the remains of dead plants and animals buried under the earth for a
long time. These are non-renewable sources of energy, which, if exhausted, can not be
replenished in a short time. Their reserves are limited and are considered very
precious. These should be used with care and caution to let them last long. These are
also contributing to the global environmental pollution.

(i) Coal

Since the advent of industrialization coal has been most common source of energy. In
the last three decades, the world switched over from coal to oil as a Major source of
energy because it is simpler and cleaner to obtain useful energy from oil. Coal is a
complex mixture of compounds of carbon, hydrogen and oxygen. Small amounts of
nitrogen and Sulphur compounds are also presenting coal. It is mainly available in
Bihar, West Bengal, Orissa and Madhya Pradesh. The big coal mines in our country
are at Jharia and Bokaro in Bihar and at Raniganj in West Bengal. It is considered as
the backbone of the energy sector for its use in industry, transportation and electric
power generation. Depending upon the carbon contents of coal, it is classified as
follows:

Type of coal Carbon content (%)

1. Peat 60
2. Lignite (soft coal) 70
3. Bituminous (house hold coal) 80
4. Anthracite (hard coal) 90
It is clear that peat is the most inferior quality of coal. Whereas Anthracite is the most
superior quality of coal. Bituminous is most commonly used in households and
industry.

4


On strong heating, coal breaks up to produce coal gas, ammonia, coaltar and coke.
Coke is 98% carbon, obtained after losing all its volatile constituents during
destructive distillation of coal. It can be used as smoke free fuel.

(ii). Petroleum

It is a dark coloured, viscous and foul smelling crude oil. Thepetroleum means rock
oil. It is normally found under the crust of earthtrapped in rocks. The crude oil is a
complex mixture of several solid liquidgaseous hydrocarbons mixed with water, salt
and earth particles. It is anatural product obtained from oil wells.
Some of the crude oil producing locations in our country are:

(i) Ankleshwar and Kalol in Gujarat
(ii) Rudrasagar and Lakwa in Assam; and
(iii) Bombay high (off-shore area)

The oil wells of Bombay high are producing about 22 million tons of crude petroleum
oil per year, which is little less than half of the total requirement of the country. The
efforts are also being made to search oil welling off-shore deltas to Godavari, Kaveri,
and Rajasthan. The crude petroleum is refined by the process of fractional distillation
to obtain more useful petroleum products. The crude petroleum is heated temperature
of about 400C in a furnace and vapors thus formed are passed into a tall fractioning
column from near its bottom. As the mixture of hot vapours rises in the column, it
starts getting cooled gradually. The products obtained from crude petroleum as
follows:

(i) Petroleum gas (below 40oC) used as LPG.
(ii) Petrol (40oC to 170oC) for light vehicles.
(iii) Kerosene (170 to 250oC) for household and industrial use.
(iv) Diesel oil (250 to 350oC) for heavy vehicles.
(v) Residual oil ; (a) Lubrication oils (b) paraffin wax and (c) asphalt
(vi) Fuel oil (350 to 400oC) for boilers and furnaces.

5


(ii) Natural gas

It consists about 95% Methane and rest ethane and propane. It occurs deep under the
crust of the earth either alone or a long with oil above the petroleum deposits. It is a
product of petroleum mining. The gas is available in Tripura, Jaisalmer, off-shore
areas of Bombay High and in the Krishna – Godavari delta. It is used as a domestic
and industrial fuel. The natural gas is now also available as CNG (Compressed
Natural Gas) a substitution of petrol in automobiles.

(b) Hydraulic energy (or) Water power

Water power is developed by allowing water to fall under the force of gravity. It is
used almost exclusively for electric power generation, in fact, the generation of water
power on a large scale became possible around the beginning of the twentieth century
only with the development of electrical power plants or Hydro electric plants were
usually of small capacities usually less than 100 KW. Potential energy of water is
converted into Mechanical energy by using prime moves known as hydraulic turbines.
Water power is quite cheap where water is available in abundance. Although capital
cost of hydro electric power plants is higher as compared to other types of power
plants but their operating Costs are quite low, as no fuel is required in this case. The
development rate of hydropower is still low, due to the following problems:

1. In developing a project, it will take about 6-10 years time for planning,
investigation and construction.

2. High capital investment is needed, and some parts of the investment have
to be designed from foreign sources.

3. There are growing problems on relocation of villages, involved, compensation for
damage, selecting the suitable resettlement area and environmental impact. Because
of long transmission line to the villages with low load factor, the electric power will

6


be available to the people in rural areas may not be economical. This leads to the
development of Mini or Micro hydroelectric projects to supply the electric power to
remote areas. The Importance of Micro hydroelectric projects have been observed in
some parts of the country with availability of river flow through out the year. In order
to reduce the cost of development several Measures have been considered as follows:

(a) Development of low cost turbines and generators.
(b) Participation of villages in the development and operation of the project.
(c) Using the appropriate technology and tolerable substandard requirement
and project civil work component at the beginning stage.

(c) Nuclear energy

According to modern theories of atomic structure, matter consists of minute particles
known as atoms. Heavier unstable atoms such as U235, Th239, liberate large amount
of heat energy. The energy released by the complete fission of one Kg of Uranium
(U235), is equal to the heat energy obtained by burning 4500 tones of coal (or) 220
tons of oil. The heat produced by nuclear fission of the atoms of fissionable material
is utilized in special heat exchangers for the production of steam which is then used to
drive turbo generators as in the conventional power plants. However there are some
limitations in the use of nuclear energy namely high capital cost of nuclear power
plants, limited availability of raw materials, difficulties associated with disposal of
radio active waste and shortage of well trained personnel to handle the nuclear power
plants. The Uranium reserves in the world at present are small. These reserves are
recoverable but are expensive. The presently working power plants are:

1. Tarapur atomic power station in Maharashtra
2. Ranapratap sagar atomic power station near Tota, Rajasthan
3. Kalpakkam atomic power station near Madras, Tamilnadu.
4. Narora atomic power station in U.P.
About 3% of the energy produced in India is obtained from nuclear power plants.

7


1.4.2. Non-Conventional Energy Sources

The sources of energy which are being produced continuously in nature and are in
exhaustible are called renewable sources of energy (or) non-conventional energy.
Some of these sources are:
(a) Wind energy
(b) Tidal energy
(c) Solar energy

(a) Wind energy
Winds are caused because of two factors.
1. The absorption of solar energy on the earth’s surface and in the atmosphere.

2. The rotation of the earth about its axis and its motion around the Sun. A wind mill
converts the kinetic energy of moving air into Mechanical energy that can be either
used directly to run the Machine or to run the generator to produce electricity.

(b) Tidal energy
Tides are generated primarily by the gravitational attraction between the earth and the
Moon. They arise twice a day in Mid-Ocean. The tidal range is only a Meter.
Basically in a tidal power station water at high tide is first trapped in a artificial basin
and then allowed to escape at low tide. The escaping water is used to drive water
turbines, which in turn drive electrical generators.

(c) Solar energy
Brief history of solar energy (or) Importance of solar energy: Energy from the sun is
called solar energy. The Sun’s energy comes from nuclear fusion reaction that take

place deep in the Sun. Hydrogen nucleus fuse into helium nucleus. The energy from
these reactions flow out from the sun and escape into space.

8


CHAPTER – 2 SOLAR ENERGY

2.1. Introduction

Energy from the sun is called solar energy. The Sun’s energy comes from nuclear
fusion reaction that takes place deep in the sun. Hydrogen nucleus fuses into helium
nucleus. The energy from these reactions flow out from the sun and escape into space.
Solar energy is some times called radiant energy. These are different kinds of radiant
energy emitted by sun. The most important are light infrared rays. Ultra violet rays,
and X- Rays. The sun is a large sphere of very hot gases. It’s diameter is1.39x106KM.
While that of the earth is 1.27x104 KM. The mean distance between the two is
1.5x108KM. The beam radiation received from the sun on the earth is reflected in to
space, another 15% is absorbed by the earth atmosphere and the rest is absorbed by
the earth’s surface. This absorbed radiation consists of light and infrared radiation
with out which the earth would-be barren. All life on the earth depends on solar
energy. Green plants make food by means of photosynthesis. Light is essential from
in this process to take place. This light usually comes from sun. Animal get their food
from plants orgy eating other animals that feed on plants. Plants and animals also
need. Some heat to stay alive. Thus plants are store houses of solar energy. The solar
energy that falls on India in one minute is enough to supply the energy needs of our
country for one day. Man has made very little use of this enormous amount of solar
energy that reaches the earth.

2.2 Solar Constant

The sun is a large sphere of very hot gases, the heat being generated by various kinds
of fusion reactions. Its diameter is 1.39x106 KM. While that of the earth is 1.27x104
KM. The mean distance between the two is 1.50x108KM. Although the sun is large, it
subtends an angle of only 32 minutes at the earth’s surface. This is because it is also a
very large distance. Thus the beam radiation received from the sun on the earth is
almost parallel. The brightness of the sun varies from its center to its edge. However

9


for engineering calculations, it is customary to assume that the brightness all over the
solar disc in uniform. As viewed from the earth, the radiation coming from the sun
appears to be essentially equivalent to that coming from a back surface at
5762ok.“The rate at which solar energy arrives at the top of the atmosphere is called
solar constant Isc”. This is the amount of energy received in unit time on a unit area
perpendicular to the sun’s direction at the mean distance of the earth from the sun.
Because of the sun’s distance and activity vary through out the year; the rate of arrival
of solar constant is thus an average from which the actual values vary up to 3 percent
in either direction. The National Aeronautics and Space Administration’s (NASA)
standard value the solar constant, expressed in three common units, is as follows:

(i) 1.353 kilowatts per square meter
(ii) 116.5 Langleys per hour (1 langely being equal to 1cal/cm2 of solar radiation
received in one day)
(iii) 429.2 Btu per Sqr.ft. per hour.
The distance between the earth and the sun varies a little through the year. Because of
this variation, the extra – terrestrial flux also varies. The earth is closest to the sun in
the summer and farthest away in the winter. This variation in the Intensity of solar
radiation (I) that reaches the earth. This can be approximated by the equation.

I 360(n-2)
-------- = 1+ 0.033 Cos -------------
ISC 365
360 x n
= 1 + 0.033. Cos --------------
365
Where n is the day of the year.

2.3 Solar Radiation at the Earth’s Surface

The solar radiation that penetrates the earth’s atmosphere and reaches the surface
differs in both amount and character from the radiation at the top of the atmosphere.

10


In the first place. Part of the radiation is reflected back in to the space, especially by
clouds. Further more, the radiation entering the atmosphere is partly absorbed by
molecules in the air. Oxygen and Ozone(o3), formed from oxygen, absorb nearly all
the Ultraviolet radiation, and water vapour and carbon dioxide absorb some of the
energy in the infrared range. In addition, part of the solar radiation is scattered (i.e. its
direction has been changed) by droplets in clouds by atmosphere molecules, and by
dust particles.

2.4 Instruments for measuring solar radiation and sun shine

Solar Radiation flux is usually measured with the help of a pyranometer or a
Pyrheliometer, sunshine recorder is used for measuring sunshine.

2.4.1. Pyranometer

A pyranometer is an instrument which measures either global or diffuse Radiation
over a hemispherical field of view. A sketch of the Instrument as Installed for the
measurement of global radiation is shown in fig.2.1. Basically the pyranometer
consists of a ‘black’ surface which heats up when exposed to solar radiation. Its
temperature increases until its rate of heat gain by solar radiation equals its rate of
heat loss by convection, conduction and radiation. The hot Junctions of a thermopile
are attached to the black surface. While the cold Junctions are located in such a way
that they do not receive the radiation. As a result, an e.m.f. is generated. This emf
which is usually in the range of 0 to 10MV can be read, recorded or Integrated over a
period of time and is a measure of the global radiation.

2.5 Solar Energy Utilization – Basic ideas about the pre-historic way
of using solar energy.

Energy is a common Man’s daily commodity: The world energy consumption in 1975
was 8002 million tons of coal equivalent and is expected to shoot up to 27,400 million

11


tons of coal equivalent in the year 2000. It is becoming scarce day by day even then
its demand is on the increase. The increased population has led to depletion of energy.
The process of mankind has influenced the subsequent exploitation of new sources of
energy from time to time. The utilization of coal, the development of hydro
electricity, the discovery of oil and gas and the advents of nuclear energy are
significantly mile stones in human history. Each new source brought about a
preformed change in the life style of the people. Each new source supplemented the
other. The size of the balance of fossil fuels will be over within a hundred, years.
Hence it is essential to tap the other sources of energy to supplement the existing
energy demands of all non-conventional energy source, solar energy holds the greatest
promise as it is abundant, renewable and pollution free. Its collection, storage on
conversion is also easy. Hence worldwide attention is now focused on various
methods of utilization of solar energy. All life on the earth depends on solar energy.
Green plants make food by means of photosynthesis. Light is essential from in this
process to take place. This light usually comes from sun. Animals get their food from
plants are store houses of solar energy. The solar energy that falls on India in one
minute, is enough to supply the energy needs of our country for one day. Man has
made very little use of this enormous amount of solar energy. That reaches the earth
he has used solar energy indirectly, for many thousands of years. Wind mills which
are driven by wind those results from infrared solar energy.

2.6 Solar Energy applications

1. Heating and cooling of residential building.
2. Solar water heating.
3. Solar drying of agricultural and animal products.
4. Salt production by evaporation of seawater.
5. Solar cookers.
6. Solar engines for water pumping.
7. Solar Refrigeration.
8. Solar electric power generation.
9. Solar photo voltaic cells, which can be used for electricity.
10. Solar furnaces.

12


2.6.1 Solar Collectors

A solar collector is a device for collecting solar radiation and transfers the energy to
fluid passing in contact with it. Utilization of solar energy requires solar collectors.
These are generally of two types.
(i) Non- concentrating (or) flat plate solar collector.
(ii) Concentrating (focusing) type solar collector.
The solar energy collector, with its associated absorber, is the essential component of
any system for the conversion of solar radiation in to more usable form (e.g heat or
electricity). In the non-concentrating type, the collector area is the same as the
absorber area. On the other hand, in concentrating collectors, the area intercepting the
solar radiation is greater. By means or concentrating collectors, much higher
temperatures can be obtained than with the non-concentrating type. Concentrating
collectors may be used to generate medium pressure steam. They use many different
arrangements of mirrors and lenses to concentrate the sun’s rays on the boiler. This
type shows better efficiency than the flat plate type. For best efficiency, collectors
should be mounted to face the sun as it moves through the sky.

(i) Flat plate collectors (non-concentrating)

Where temperatures below about 90oC are adequate as they are for space and service
water heating flat plate collectors, which are of the non concentrating type, are
particularly convenient. They are made in rectangular panels from about 1.7 to 2.9
sq.m, in area, and are relatively simple to construct and erect. Flat plates can collect
and absorb both direct and diffuse solar radiation, they are consequently partially
effective even on cloudy days when there is no direct radiation. Flat plate solar
collectors may be divided into two main classifications based on the type of heat
transfer fluid used.

13


(ii) Concentrating (focusing) type solar collector

Focusing collector or concentrating type solar collector is a device to collect solar
energy with high intensity of solar radiation on the energy absorbing surface. Such
collectors generally use optical system in the form of reflectors or refractors. A
focusing collector is a special form of flat-plate collector modified by introducing a
reflecting or refracting surface between the Solar Radiation and the absorber. In these
collectors radiation falling on a relatively large area is focused on to a receiver or
absorber of considerably smaller area. As a result of the energy concentration, fluids
can be heated to temperatures of 5000C or more.

2.6.7 Electricity from Solar Energy

Electricity energy is the most convenient form of energy. It is easy to use, transport,
control and transform into other forms of energy. Modern society has an insatisfiable
hunger for energy. This need for energy will continue to increase as the newly
developing countries become more industrialized and the mature nations increase
their scope of Mechanization. To satisfy this need, vast quantities of coal and
petroleum products are required. More recently, the advent of nuclear energy has
added vast quantities for future needs. Although sun is the ultimate source of all the
power which man has at his disposal, the conversion of solar radiation directly into
electrical power by some cheap and efficient means has been sought for several
decades. Many different methods have been tried for this purpose, but none of these
could complete with conventional fossil fuel or hydro electric power plants.

2.6.8 Solar Photo Voltaics

The direct conversion of solar energy in to electrical energy by means of the photo
voltaic effect, that is the conversion of light (or other electromagnetic radiation) in to
electricity. The photo voltaic effect is defined as the generation of the electromotive
force as a result of the absorption of ionizing radiation energy conversion devices
which are used to convert sun light to electricity by the use of the photo voltaic effects

14


are called solar cells. A single converter cell is called a solar cell or more generally, a
photo voltaic cell, and combination of such cells, designed to increase the electric
power out put is called a solar module or solar array. Photo voltaic cells are made of
semi conductors that generate electricity when they absorb light. As photons are
received, free electrical changes are generated that can be collected on contacts
applied to the surface of the semi conductors. Because solar cells are not heat engines,
and therefore do not need to operate at high temperatures, they are adopted to the
weak energy flux of solar radiation, operating at tome temperature. These devices
have theoretical efficiencies of the order of 25 percent. Actual operating efficiencies
are less than this value, and decrease fairly rapidly with increasing temperature. The
best known applications of photo voltaic cells for electrical power generation have
been is spacecraft, for which the Silicon cell is the most highly developed type. The
Silicon cell consists of a single crystal of silicon into which a doping material is
diffused to from a semi conductor. Since the early day of solar cell development,
many improvements have been manufactured with areas 2x2Cm, efficiencies
approaching 10 percent, and operating at 28oC. The efficiency is the power developed
per unit area of array divided by the solar energy flux in the free space (1.353
KW/m2). For terrestrial applications, silicon solar cells have shown operating
efficiencies of about 12 to 15 percent. Though Silicon is one of the earth’s most
abundant materials, it is expensive to extract (from sand, where it occurs mostly in the
from SiO2) and refine to the purity required for solar cells. The greater barrier to solar
cell application lies in the costs of the cells themselves. Reducing the cost of Silicon
Cells is difficult because of the cost of making single crystal. One very promising
method is being developed to produce continuous thin ribbons of single-crystal
Silicon to reduce fabrication costs. Cells made from the ribbon have so for shown
efficiencies of around 8 percent. Several other kinds of photo cells are in the
laboratory stage of development. Cadmium Sulfide cells are other possibilities. So far,
efficiencies have been in the range of 3 to 8 percent and these cells have, been less
durable than Silicon cells owing to degradation with exposure to Oxygen, water vapor
and sunlight, especially at elevated temperatures. The active part of the Cadmium
Sulfide cds cell is a thin polycrystalline layer of cds, about 10μm. Thick on which a
layer of Cu2S compound perhaps 0.1μm thick is grown. These cells can be made by

15


deposition on long sheets of substrates, a process that might be adaptable to expensive
mass production.
Photo voltaic cells could be applicable to either small or large power plants, since
they function well on a small scale, and may be adaptable to local energy generation
on building roof tops. The cost of the energy storage and power conditioning
equipment might, however, make generation in large stations the most economical
method; solar cells have also been used to operate irrigation pumps, navigational
signals high way emergency call system, rail road crossing warnings, automatic
meteorological stations, etc; in location where access to utility power lines is difficult.

2.6.9 Applications of Solar Photo-Voltaic System in Rural Areas

A variety of PV system configurations have been developed and deployed for rural
applications such as drinking water supply, street lighting irrigation water pumping
and for operation of electronic equipment’s. Government of India is sponsoring, a
program for Popularizing solar lighting, solar water pumping etc; by providing capital
subsidies and concessional interest on borrowed capital.

Solar lighting

Electricity for lighting during night is one of the most convenient and preferred form
of energy. However in our Country out of 6 Laks villages, 1 lakh villages are still to
be electrified. Even in electrified villages, only a quarter of house-holds have proper
connection. Owing to power shortage in many stages, electricity supply situation in
villages is precarious and mostly it is not available even in electrified villages for
lighting when it is most needed. The bulk of rural house-holds in India, normally use
kerosene lanterns for meeting their lighting requirements. It is estimated that around
100 million kerosene lanterns are used in India. These lanterns provided
Insufficient and poor quality of light.
For village lighting, three major systems Configuration are available;
(1) Domestic lighting system or solar lantern.
(2) Pole mounted stand alone street lighting system.
(3) Non-grid interactive centralized lighting system.

16


(i) Solar lantern

Solar photo-voltaic powered lights called lanterns are considered to be ------------------
Alternative solution to village lighting needs. A typical solar lantern consists of small
photovoltaic module, alighting device, a high frequency investor, battery charge
controller and appropriate housing. During day time, module is placed under the sun
and is connected to lantern through cable for charging a typical lantern uses a 10 watt
lamp. The expected life of the lamp is 3 to 5 years. Storage battery is one crucial
component in lantern, Recombinant maintenance free absorbed electrotype batteries
are being used. The battery has a life of 3 to 5 years. Sealed nickel Cadmium battery
is a good option considering their deep discharge characteristics. It is important to
have reliable electronics to operate the lamp and provide suitable protection. A high
frequency investor is being used to excite compact fluorescent lamp and a charge
controller which protect battery from over charging.

17


CHAPTER – 3 WIND ENERGY

1.0 INTRODUCTION

Winds are caused because of two factors.
(1) The absorption of solar energy on the earth’s surface and in the
atmosphere.
(2) The rotation of the earth about its axis and its motion around the sun. Because of
these factors, alternate heating and cooling cycles occur, differences in pressure are
obtained, and the air is caused to move. The potential of Wind energy as a source of
power is large. This can be judged from the fact that energy available in the wind over
the earth’s surface is estimated to be 1.6x107 K.W Besides the energy available is free
and clean. The problems associated with Utilizing wind energy are that:
(i) The energy is available in dilute form, because of this conversion
machines have to be necessarily large.
(ii) The availability of the energy varies considerably over a day and with the
seasons.
For this reason some Means of storage have to be devised if a continuous supply of
power is required. A wind mill converts the kinetic energy of moving air into
mechanical energy that can be either used directly to run the machine or to run the
generator to produce electricity.

Classification of wind mills

(a) Horizontal Windmills

(b) Vertical Windmills

(a) Horizontal Wind mills

18


i. Horizontal Axis single blade Wind mills

If extremely long blades are mounted on rigid hub. Large blade root bending moments
can occur due to tower shadow, gravity and sudden shifts in wind directions on a
200ft long blade. Fatigue load may be enough to cause blade root failure. To reduce
rotor cost, use of single long blade centrifugally balanced by a low cost counter
Weight as shown in fig3.1. The relatively simple rotor hub consists of a Universal
Joint between the rotor shaft and blade allowing for blade. This type of hub design
contains fewer parts and costs less.

(ii) Horizontal axis – two bladed wind mills

In this arrangement rotor drives generator through a step-up gear box. The
components are mounted on a bed plate which is mounted on a pinttle at the Top of
the tower. The two blade rotor is Usually designed to be oriented down wind of the
tower.
(iii) Horizontal Axis – Multi bladed Wind Mills

This type of wheel has narrow rims and Wire spokes. The wire spokes support light
weight aluminum blades. The rotors of this design have high strength to weight ratios
and have been known to survive hours of free wheeling operation in 100kmph winds.
They have good power Co-efficient, high starting torque ad added advantage of
simplicity and low cost.

(b) Vertical Wind Mills

Wind turbines mounted with the axis of rotation in a vertical Position have advantage
that they are omni-directional that is, they need not to be turned to Force the wind.
The Vertical mounted Wind Machines eliminates the need for some of the complex
mechanical devices and control systems necessary for horizontal mounted wind
Machines. Two types of vertical axis Wind Machines have received attention. The

19


Darrievs rotor consists of two or three convex metal blades with an air foil cross
section, mounted on a Central shaft which is supported by bearings at the top and
bottom. The rotor assembly is held in position by guy wires running from the top of
the rotor to the ground. The savonius rotor consists of a long solid’s- shaped surface
mounted to turn at the center of ‘s’ the savonius rotor is self starting and has an
efficiency of about 31% while the Darrievs rotor has a slightly higher efficiency
of 35% but is not self starting.

Advantages of Wind energy

(1) The wind energy is free, inexhaustible and does not need transportation.
(2) Wind mills will be highly desirable and economical to the rural areas
which are far from existing grids.
(3) Wind power can be used in combination with hydroelectric plants. Such that the
water level in the reservoir can be maintained for longer periods.

Disadvantage of Wind energy

(1) Wind power is not consistent and steady, which makes the complications in
designing the whole plant.
(2) The wind is a very hazard one. Special and costly designs and controls are always
required.
(3) The cost factor, which has restricted the development of wind power in large scale
for feeding to the existing grid .
(4) It has low power coefficient.
(5) Careful survey is necessary for plant location.

20


CHAPTER – 4 BIOENERGY

4.1 Introduction

Bio gas is generated through a process of anaerobic digestion of Bio Mass. Bio Mass
is organic matter produced by plants, both terrestrial (those grown on land) and
aquatic (those grown in water) and their derivatives. It includes forest crops and
residues, crops grown especially for their energy content on “energy farms” and
animal manure. Unlike coal, oil and natural gas, which takes Millions of years to
form, bio mass can be considered as a renewable energy source because plant life
renews and adds to it self energy year. It can also be considered a from of solar energy
as the latter is used indirectly to grow these plants by photosynthesis. Bio Mass means
organic matter and Photo Chemical approach to harness solar energy means
harnessing of solar energy by photo synthesis. Solar energy is stored in the from of
chemical energy. Hence solar energy –> Photosynthesis –> Bio Mass->energy
generation. Out of several sources of renewable energy like solar, wind, tidal, wave
energy, Geothermal energy, nuclear energy, energy through bio mass are important
features in our Country. Biogas Production Technology contributes
in following ways.

Advantages of Bio Gas technology

(1) It provides a better and cheaper fuel cooking, lighting and for power
generation.
(2) It produces good quality, enriched manure to improve soil fertility.
(3) It proves an effective and convenient way for sanitary disposal of human excreta,
improving the hygienic conditions.
(4) It generates social benefits such as reducing burden on forest for meeting cooking
fuel by cutting of tree for fuel wood, reduction in the drudgery of women and children
etc.
(5) As a smokeless domestic fuel, it reduces the incidence of eye and lung diseases.

21


Bio Gas and its Compositions

Bio gas contains 55-70% methane and 30-45% carbon dioxide as well as small
quantities of(N2, H2, H2S) some gases. It is lighter than the air and has an ignition
temperature of approximately 700oC. The temperature of the flame is 870oC. its
calorific value is approximately 4713kcal/m3.

4.2.2 History of Bio-gas

In the field of an aerobic digestion of waste Material India and China are recognized
world leaders. This practice is based upon an age-old tradition of composting human,
animal and plant wastes to produce and organic fertilizer. In fact bio gas programme
has been recognized for making available a clean and efficient fuel for cooking,
lighting, engine and the liquid slurry as a fertilizer and soil conditioner all over the
World. Since the 1920’s there have been sporadic attempts made to recover bio gas
from sewage wastes and animal dung. A few bio gas plants for sewage disposal and
bio gas recovery were installed in Europe and the U.S.A. in 1920’s and 1930’s --------
respectively. Although the Chinese have been experimenting with bio gas since the
1950’s and China had its first bio gas Plant in 1936, yet it was reported only in the
70’s in Sichvan. Mainly, there was a movement to extend the practice and reproduce
the digester in a large way throughout the country side. The history of bio gas from
cattle dung in India goes back to 1939 when Indian Agricultural Research Institute
(ARI) New Delhi, was able to ferment cattle dung to produce Methane. Subsequently
Proof N.V.Joshi; at Poona patented a model of bio gas plant in 1945. Later on
Jashbhai, J.Patel evolved a simple model called “Gramalaxmi” and patented it in the
year 1951. Mean while, J.J.Patel continued his efforts to simplify his eariler patented.
Model, which resulted in the development of two chamber digester with central guide
for free up and down movement of steel gas holder. This design was accepted by the
Khadi and Villages Industries Commission (KVIC) Bombay, in India during 1962.
Subsequently, many Scientists, Engineers, Government, SemiGovernment and
different social organisations contributed to the development of bio-gas, technology.
The Planning Research and Action Division (PRAD) of State Planning Institute,
Government of Uttar Pradesh, Lucknow developed a cheap andconvenient model of

22


bio gas in 1957, and called it Janata bio gas plant. After independence the Ministry of
Agriculture, Government of India, was looking the bio-gas programme, related
development and extension activities. K.V.I.C and state Government’s continued the
programme in 1970-1980. The national Project on Bio-gas development was launched
in 1980-81 under Ministry of Agriculture. Currently Department of non-conventional
energy source(DNES), the Ministry of Power and Non-Conventional energy is also
actively involved in supporting research and diffusion of bio gas technology and
many institutions and State Agricultural Universities are supporting research
programme on bio gas technology.

4.2 Process of Bio gas, generation

(i) Wet process

(a) Anaerobic digestion

Bio gas is produced by the bacterial decomposition of wet sewage sludge, animal
dung or green plants in the absence of oxygen. Feed stocks like – wood shavings,
straw, and refuse maybe used, but digestion takes much longer. The natural decay
process ‘anaerobic decomposition’ can be speeded up by using a thermally insulated,
air-tight tank with a stirrer Unit and heating system. The gas collect in the digester
tank above the slurry and can be piped off continuously. At the optimum temperature
(35oC) complete decomposition of animal or human farces takes around 10 days. Gas
yields depend critically on the nature of the waste-Pig manure, for example, is better
than cow dung or house hold refuse. The residue left after digestion is valuable
fertilizer. It is also rich in protein and could be dried and used as animal feed
supplement.
(b) Fermentation

As stated, ethanol or ethyl alcohol is produced by the Fermentation of sugar solution
by natural yeast’s. After 30 hours of fermentation the brew or ‘beer’ contains 6-10%
alcohol and this can readily by removed by distillation.Traditionally, the fibrous

23


residues from plant crops like sugar cane bagasse have been burnt to provide the heat.
Suitable feed stocks include crushed sugar came and beet, fruit etc sugar can also be
manufactured from vegetable starches and Cellulose, Maize, Wheat grain, or Potatoes.
For they must be ground or pulped and then cooked with enzymes to release the
starch and convert it to fermentable sugars. Cellulose materials like wood, paper
waste or straw, require harsher pre-treatment typically milling and hydrolysis with hot
acid. One tone of sugar will produce up to 520 liters of Alcohol, a tonne of grain, 350
liters and a tonne of wood, an estimated 260 to 540 liters. After fermentation, the
residue from grains and other feed syffs contains high protein content and is a useful
cattle-feed supplement. The hydrolysis and distillation step require a high energy
input; for woody feed stocks direct combustion or pyrolysis is probably more
productive at present, although stem treatment and new low-energy enzymatic
hydrolysis techniques are under development. The energy requirement for distillation
is also likely to be cut drastically. Alcohol can be separated from the beer by many
methods which are now under intensive development. These include solvent
extraction, reverse osmosis, molecular sieves and use of new desiccants for alcohol
drying. It may soon be possible to have the energy required for alcohol production to
produce a greater net energy gain.

(ii) Dry Process

Pyrolysis
A wide range of energy-rich fuels can be produced by roasting dry woody matter like
straw and wood-chips. The material is fed into a reactor vessel or retort in a
pulverized or shredded form and heated in the absence of air. As the temperature rises
the cellulose and lignin break down to simpler substances which are driven off
leaving a char residue behind. This process has been used for conturies to produce
charcoal. The end products of the reaction depend critically on the conditions
employed, at lower temperatures around 500oC, organic liquid predominate, whilst at
temperatures nearer 1000oC combustible mixture of gases results.

24


4.3 Raw Materials available for Bio gas Fermentation

(i) Manure: This kind of Material is available from animal waste and poultry waste.
Their compositions vary with the feeding stuff. In rural areas, the fresh manure is
used to be fermented with shorter retention time (about two months). The manure
from human, cattle, chicken and pigs are subject to inhabitation when fermented
without other Carbon source. Manures can be used as Bio mass.

(ii) Plants: Most of the Plants of the grass family can be used for fermentation.
Both aqnolic and terrestrial plants can be used as Bio mass. As such they are difficult
to be biodegraded. In order to ferment them more easily, pretreatment and a longer
retention time are generally needed. Adequate amount of nitrogen rich elements urea
etc; should be added for the fermentation.

(iii) Industrial Organic Waste Water: Industrial effluents from food
processing, biochemical pharmacy, paper making etc; can be treated by anaerobic
fermentation. Most organic matters of these liquid are soluble and their composition
are more stable than that of agricultural wastes, while the water quantities may
fluctuate. Some effluents may be nutrient deficient or even toxic. Thus pretreatment,
such as the elimination of toxicity, adding nutritional additives and so on, or
necessary for anaerobic digestion. In food processing Industries plenty of organic
waste will available. By utilizing two organic wastes we can produce Bio gas by
anaerobic digestion.

(iv) Organic Matter in Municipal Wastes: They are in solid and inorganic
contents need separation. Organic matter is availble in Muncipal wastes. By utilizing
this organic matter. Bio-gas can be produced.

25


4.4 Selection of site for Installation of a Bio gas plant
Careful selection of the best site for installation of a bio gas unit should be done for
every beneficiary. The following points should be taken into consideration.
(1) The distance between the plant and site of gas consumption or kitchen should be
less to Minimize cost on gas pipe line and gas leakage. For a plant of capacity 2m3,
the optimum distance is 10 Cm.
(2) It should be near the cattle-shed to minimize the distance for carrying cattle dung
and transportation cost.
(3) There should be enough space for storage of digested slurry or construction of
compost pit.
(4) It is should be 10 to 15 meters away from any drinking water well to prevent
contamination of water.
(5) The area should be free from roots of trees which are likely to creep into the
digester and cause damage.
(6) It should be open to receive the Sun’s rays for most part of the day and to keep the
plant in warm. The sunlight should fall on the plant as temperature between 15oC to
30oC is essential for gas generation at good rate.
(7) It should be on an elevated area so that the plant does not get submerged during
normal rains.
(8) Sufficient space must be available for day to day Operation and Maintenance. As a
guide line 10 to 12 M2 area is needed per M3 of the gas.
(9) Plenty of water must be available as the Cow dung slurry with a solid
concentration of 7% to 9% is used.

4.5Utilization and benefits of Biogas Technology

(i) It provides simultaneous dual benefits in terms of fuel for cooking and lighting as
well as fertilizer.
(ii) Bio gas burns efficiently without smoke or smell and eleminates the possibility of
eye and lung diseases caused by smoke.
(iii) It reduces the drudgery of women and children in terms of providing relief from
the collection of fire wood and preparation of dung cakes.

26


(iv) The gas can also be used in dual-fuel engines, where up to 80% of the diesel can
be replaced with biogas.
(v) Besides gas, the digested slurry can be used as natural fertilizer which improves
the soil fertility.
(vi) Utilization of waste materials in the plant not only improves the sanitary
condition of your village but also prevents deforestation and assures eecollegial and
environmental balance. Bio gas is a cheep and clean fuel. It burns with a blue flame.
Which is smoke-free. When it is burnt in silk mantle lamps, it illuminates better than
kerosene in petromax lanterns. Bio gas can replace Petrol and diesel in
engines.

4.6. Economical, social environmental and health benefits of bio gas
Utilization

Economical benefits of bio gas utilization

From the national economic point of view the bio gas yields following economic
benefits:
(1) Bio gas technology, which is based on recycling of readily available resources in
rural areas, gives comparatively cheaper and better fuel for cooking lighting and
power generation.
(2) An individual can reduce the consumption of commercial energy sources such as
fire wood, coal, kerosene, etc. by adopting waste recycling technology which
vigorously help in reducing the family fuel budget.
(3) The problem of uncertainly of availability of commercial energy can be resolved
by use of bio gas technology.
(4) The rural population of the country uses fire wood for meeting their cooking
requirements. This reduces the national forest wealth. Our forest area can be
conserved by using bio gas.
(5) The dependency on chemical fertilizer for better-agricultural production has
increased to a great extent after independence in India. Bio gas slurry can be proved a
best organic fertilizer which helps in improving soil fertility and crop production.

27


(6) Presently country is facing the problem of foreign exchange and balance of --------
payment. Bio gas technology reduces the import of chemical fertilizers by using home
made organic fertilizer and also petroproducts.
(7) Bio gas technology utilizes effectively, the man power and resources, resulting in
self-sufficiency and self reliance in the society.

Social Benefits

Bio gas is one of the best options in rural areas, which provides self sufficiency in
energy and helps in increasing standard of living of rural people. The social benefits
from bio gas utilization are as follows:

(1) Bio gas burns giving shootless flame and smokeless cooking, as such it provides
cleanliness in the houses.
(2) The cooking on bio gas is faster and also women is not required to waste their
time to collect fuel from forest, as such it reduces the drudgery of women who can use
her free time for other developmental activities.
(3) The bio gas provides lighting in the rural areas, which are far away from electrical
supply lines. Thus it helps the children to use their time in study of employment.
(4) It helps in generation of employment opportunities to village artisans. This also
stops the Migration of people from rural to urban areas in search of employment.
(5) Generally, rural women and children spend their energy and time for collection of
fuel, chopping wood, collecting wood and crop stalks or buying coal or kerosene for
cooking from distant places, energy and time saved due to sue of bio gas can be used
for constructive work or going to school for education.

Environmental and Health Benefits

Bio gas system contributes to maintain clean and healthier environment by processing
human growth. More transportation means have increased the pressure on --------------
environment. The scientists are worried about environmental protection and looking
for appropriate means for the same, which are locally available. In present

28


circumstances bio gas utilization would be a solution for environmental protection for
healthy and prosperous society. Environmental benefits from bio gas are enormous.
Some of them are as under:
(1) lungs and eye diseases are very common among village women and children due
to smoky kitchen. Bio gas utilization reduces the disease spread. Thus reducing health
problem rush in hospitals and waste of national wealth.
(2) Sanitation problems in villages through systematic collection and through proper
processing of animal dung and human excreta will be solved.
(3) It helps to prevent deforestation. consequently it controls soil erosion, and floods.

29


CHAPTER – 5 TIDAL POWER PLANTS

5.0 Introduction to Tidal Power Plants

The development of a nation is estimated from the total amount of energy it produces
and consumes in relation to its size and Population. Human-Progress has been judged
from the ways in which man has been able to develop and harness energy. The present
shortage of the energy production sources due to deplitable nature of fossil flues has
awakened the world human community to search for new unconventional and
replenishable energy sources. According to the energy experts, exhaustible resources
extracted from the ground (coal, oil, gas, and uranium), in the face increasing demand,
results into a cycle. This cycle starts at zero production increases exponentially than
decreases exponentially and finally comes to zero. It is estimated that Petroleum
reserves of the world will be nearly exhausted by 2020. Under such circumstances,
man has to find out some source of energy for his survival. In this context, three
sources of energy, tidal, wind and solar have been brought to be most promising.
What is tidal power? Tide is periodic rise and fall of the water level of the sea. Tides
occur due to the attraction of seawater by the moon. These tides can be used to
produce electrical power which is known as tidal power. When the water is above the
mean sea level, it is called flood tide and when the level is below the mean level, it is
called ebb tide. A dam is constructed in such a away that a basin gets separated from
the sea and a difference in the water level is obtained between the basin and sea. The
constructed basin is filled during high tide and emptied during low tide passing
through sluices and turbine respectively. The Potential energy of the water stored in
the basin is used to drive the turbine which in turn generates electricity as it is directly
coupled to an alternator.
Though the idea of utilizing tides for human service relates to eleventh century when
tidal mills were used in England but the use of tidal power for electric power
generation is hardly a decade old as the world’s first Rance tidal power plant of 240
MW capacity in France was commissioned by President be Gaulle in 1965 who
described it a magnificent achievement in the human life. Tidal power has been a
dream for engineers for many years and itremained dream because of large capital
30


cost involved in its development. But after the inauguration of Rance Tidal Project, a
new chapter in the history is now opened.

5.1 Factors affecting the suitability of the site for tidal power plant

The feasibility and economic vulnerability of a tidal power depends upon the
following factors.
1. The power produced by a tidal plant depends mainly on the range of tide and the
cubature of the tidal flow occurring in the estuary during a tidal cycle which can be
stored and utilized for power generation. The cubature of the tidal flow not only
depends on the tidal range but on the width of estuary mouth.
2. The minimum average tide range required for economical power production is
more.
3. The site should be such that with a minimum cost of barrage it should be possible
to create maximum storage volume. In addition to this, the site selected should be well
protected from waves action.
4. The site should not create interruption to the shipping traffic running through the
estuary other wise the cost of the plant will increase as locks are to be provided.
5. Silt index of the water of the estuary should be as small as possible to avoid the
siltation troubles. The siltation leads to reduction of the range of tides and reduces the
power potential of the plant.
6. The fresh water prism that falls into the reservoir of the tidal plant (due to the
surface flows in the streams having out fall in the estuary) eats away the valuable
storage created for storing the tidal prism. Therefore, the ratio of fresh water prism to
tidal water prism becomes an important index in determining the economic feasibility
of a tidal scheme. The effective and cheaper will be the power production with
decreasing the ratio mentioned above.

5.2 Classification of tidal Power Plants

The tidal power plants are generally classified on the basis of the number of basins
used for the power generation. They are further subdivided as one-way or two-way

31


system as per the cycle of operation for power generation. The classification is
represented with the help of a line diagram as given below

Classification
Single basin systems Double basin systems One-way Two-way Two-way with Simple
double Double basin system system pump storage basic with pumping

5.3 Working of Different Tidal Power Plants

5.3.1 Single basin-One-way cycle

This is the simplest form of tidal power plant. In this system, a basin is allowed to get
filled during flood tide and during the ebb tide. The water flows from the basin to the
sea passing through the turbine and generates power. The power is available for a
short duration during ebb tide.

5.3.2. Single-basin two-way cycle with pump storage

The Rance tidal power plant in France uses this type of arrangement. In this system,
power is generated both during flood and ebb tides. Complex machines capable of
generation Power and Pumping the water in either directions are used. A part of the
energy produced is used for introducing the difference in the water levels between the
basin and the sea at any time of the tide and this is done by pumping water into the
basin up or down. The period of power production with this system is much longer
than the other two described earlier.

5.3.3 Double basin type

In this arrangement, the turbine is set up between the two basins as shown in Fig 5.5.
one basin is intermittently filled by the flood tide and other is intermittently drained
by the ebb tide. Therefore a small capacity but continuos power is made available
with this system as shown in Fig5.5. The main disadvantage of this system is that

32


50% of the Potential energy is sacrificed in introducing the variation in the water
levels of the two basins.

5.3.4 Double basin with Pumping

In this case, off peak power from the base load plant in a interconnected transmission
system is used either to pump the water up the high basin. Net energy gain is possible
with such a system if the pumping head is lower than the basin-to-basin turbine
generating head.

5.4 Advantages and disadvantages of Tidal Power Plants

Advantages

1. Exploitation of tidal energy will in no case make demand for large area of valuable
land because they are on bays.
2. It is free from pollution as it does not use any fuel.
3. It is much superior to hydro-power plant as it is totally independent of rain which
always fluctuates year to year. Therefore, there is certainty of power supply a the tide
cycle is very definite.
4. As in every form of water power, this will also not produce any unhealthy waste
like gases, ash, atomic refuse which entails heavy removal costs.
5. Tidal Power is superior to conventional hydro power as the hydro plants are know
for their large seasonal and yearly fluctuations in the output of energy because they
are entirely dependent upon the nature’s cycle of rainfall, which is not the case with
tidal as monthly certain power is assured. The tides are totally independent on
nature’s cycle of rainfall.
6. Another notable advantage of tidal power is that it has a unique capacity to meet
the peak power demand effectively when it works in combination with thermal or
hydroelectric system.
7. It can provide better recreational facilities to visitors and holiday makers, in
addition to the possibility of fish forming in the tidal basins.

33


Disadvantages

1. These Power plants can be developed only if natural sites are available.
2. As the sites are available on the bay which will be always far away from the load
centers. The power generated must be transported to long distances. This increases the
transportation cost.
3. The supply of power is not continuous as it depends upon the timing of tides.
Therefore some arrangements (double basin or double basin with pump storage) must
be made to supply the continuous power. This also further increases the capital cost of
the plant.
4. The capital cost of the plant (Rs.5000/kw) is considerably large compared with
conventional-power plants (hydro, thermal)
5. Sedimentation and siltration of the basins are some of the added problems
with tidal power plants.
6. The navigation is obstructed.
7. It is interesting to note that the output of power from tidal power plant varies with
lunar cycle, because the moon largely influences the tidal rhythm, where as our daily
power requirement is directly related to solar cycle. In addition to all the above
mentioned (imitations of tidal power, the utilization of tidal energy on small scale has
not yet proved economical.

34


CHAPTER – 6 FUEL CELLS

6.0 Introduction

Fuel Cells are efficient and quiet, operate on a variety of hydrocarbon fuels, and
produces almost no objectionable emissions. The concept has been proven in
numerous small scale applications. The recent infusion of power cost from fossil fuels
may convert this promising device into a major source of electric power generation.
The electric Power Research Institute and United Technologies Corporation recently
agreed to construct a 4.8MW capacity plant, with an investment of 25 million dollars.
It is predicted that if the fuel cell clears a number of technical hurdles and proves
financially viable, it could contribute 20,000MW power to the US grid, by the end of
1985. This would save $1 billion in power generating costs and 100 million barrels of
fuel oil annually.

6.1 Working of Fuel Cell

The fuel cell represents one of the successful ways by passing the heat cycle and
converting the chemical energy of fuels directly into electricity. It may be defined as
an electrochemical device for the continuous conversion of the portion of the free
energy change in a chemical reaction to electrical energy. It is distinguished from a
battery in that it operates with continuous replenishment of the fuel and oxidant at
active electrode areas and does not require recharging. The arrangement of fuel cell
components in shown in fig 6.1
The working of the fuel cell is explained here with reference to the Hydrogen-Oxygen
fuel cell using aqueous electrolyte. The fuelcell consists of an anode, a cathode and an
electrolyte Hydrogen fuel is fed into the anode side of the cell. Positive H2 ions move
from the anode-side and enter the electrolyte through porous cell walls. The anode is
left with a negative charge. Air is fed into the cathode side. O2 ions enter the
electrolyte leaving the cathode side with a positive charge. Excess anode electrons
flow to the cathode creating a current flow H2 and O2 ions combine in the electrolyte

35


to from water which leaves the cell as steam.The reaction taking place at the
electrodes are given below

(1) Hydrogen electrode (anode)
2H2 → 4H
4H + 4OH → 4H2O + 4e
(2) Oxygen electrode (cathode)
O2
→ 20
2 O + 2H2O + 4e → 4 OH
(3) Overall cell reaction
2H2 + O2 → 2H2O
The above reactions indicate H2 molecules break up into H Atoms at the anode and
they combine with OH ion to form water and free electron at anode. The formed free
electrons travel to the cathode through the external circuit as shown in fig. At the
cathode, O2 molecules break up into two O2 atoms and these atoms combine with the
four electrons arriving by the external circuit and two molecules of water (out of 4
molecules produced at the anode to from 4OH oins. The OH ions migrate towards the
anode and are consumed there. The electrolyte remains invariant. It is prime
requirement that the composition of electrolyte should not change as the cell operates.
The major difficulty experienced in the design of fuel cell is to obtain sufficient fuel-
electrode-electrolyte reaction sites in a given volume. There are many other types of
cells as ion exchange membrane cell, direct and indirect oxidation fuel cells, molten
carbonate fuel cells and many others. The present research work done in this area is to
increase the efficiencies or modify the design of the three major components of fuel
cell power plant to increase the overall efficiency of the system.

(a) Processor
It converts a hydrocarbon fuel into a hydrogen rich gas that can be accepted by the
cell. One of the main problems regarding fuel-cell development is finding away to
convert low grade fuel into H2 rich gas that has a minimum of impurities. Material
such as sulpher in fuel can adversely affect the fuel processor. Presently the research

36


is directed to find a cell electrolyte that is more tolerant of fuel impurities. It is
predicted that the developments in both processor and electrolyte will allow the use of
standard fuel oil as fuel in the 1990s and ultimately residual oil and coal gas.
Hydrogen generation processes from the petrochemical industry are being adopted to
the fuel cell’s needs steam reforming is an other successful fuel processing technique
now commonly used with phosphoric-acid electrolyte fuel cells. The life of such a
processor is presently limited to about 15,000 hrs.

(b) Electrolyte

Initial work has been done chiefly with phosphoric acid which has an operating
temperature of 160oC to 200oC. This electrolyte can give fuel cells efficiency of
50%. Next generation of fuel cells will use molten carbonate electrolyte. Operating at
a temperature of 500 to 750oC, this material is more tolerant of fuel impurities and
gives a fuel cell efficiency of 40 to 50%. Life for existing molten carbonate fuel cells
is about 10,000 hrs. A 50,000hr, life is expected to be achieved by 1990. Solid oxide
may be electrolyte of the third generation of fuel cells, which are probably 20 years
away. This electrolyte will give a fuel efficiency of 60% or better and will be
compatiable with many of the coal gasification processes.

(c) Inverter

The last element in the fuel cell power generation system which converts DC to AC
does not yet exist commercially in the sizes needed for large scale power conversion.
To date inverters with a capacity of 20 to 40KW are in limited use and some capable
of 1.8MW have been tested. Major research work is presently directed to develop the
inverters of high capacity. The predicted performance of fuel cell power plant is
shown in fig relative to three other power generation methods.

37


6.2 Advantages of Fuel Cells

1) The fuel cell converts its fuel directly to electric power. Pollutant levels range from
1/10 to 1/50,000 of those produced by a fossil fuel power plant as there it no
combustion
2) No cooling water is needed so it can be located at any desired place.
3) As it does not make noise. It can be readily accepted in residential areas.
4) The fuel cell takes little time to go into operation.
5) It would be an ideal reserve power source with in large conventional power plants
to handle peak or emergency loads.
6) There is no efficiency penalty for part load operation. Efficiency remains constant
from 100% to 25 % of rated load.
7) There is no maximum or minimum size for a fuel cell power plant. Individual fuel
cells are joined to from stacks. The stacks are joined to form power modules. The
number of modules can be tailored to power plant requirements.
8) The land requirement is considerably less compared with conventional
power plants.
9) Possibly the greatest advantage of the fuel cell is its high operating efficiency.
Present-day fuel cell efficiency is 38% and it is expected to reach to 60% before the
end of this century.
10) Fuel cell power plants may further cut generation costs by eliminating or reducing
line losses. Fuel cell power plant in rural areas or highly congested residential areas
would eliminate the need for long lines to bring in power from remote generating
stations.
11) A wide variety of fuels can be used with the fuel cell. Although presentlylimited
to using substances that produce pure H2 rich gas, the cell may one day be able to
operate on fuels derived from low grade shale oils or highly sulfur coals.
12) The maintenance charges are low as there are no moving parts and
outages are also less.
13) Fuel cells have an overload capacity of 50 to 100% for a short duration.
14) The weight and volume of the fuel cell is considerably low compared to
other energy sources.

38


REFRENCES
1. Twidell John W. and Anthony D. Weir, Renewable4 Energy Resources,
ELBS/E. and F.N. Spon Ltd.,Uk,1986
2. Rao S. and B.B. Parulekar, Energy Technology: Non Conventional,
Renewable and Conventional, Khanna Pub.3rd Ed,1999
3. Gupta B.R., Generation of Electrical Energy, Eurasia Publishing
House,1998
4. http://mnes.nic.in/
5. http://www.em-er.org/
6. http://www.nrel.gov/
7. http://www.poemsinc.org/

39

Combined report on NCES

More Related Content

What's hot (20)

Viewers also liked (14)

Similar to Combined report on NCES (20)

Combined report on NCES