Comparative Study on Dynamic Behaviour of Multi-Storey Building with and Without Coupled Shear Wall System

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 07 | July-2017 www.irjet.net p-ISSN: 2395-0072
© 2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 2905
COMPARATIVE STUDY ON DYNAMIC BEHAVIOUR OF MULTI-STOREY
BUILDING WITH AND WITHOUT COUPLED SHEAR WALL SYSTEM
Sudeep P E1, Guruprasad T N2, M A Nagesh3, Raghu K S4
1P G Student, Computer Aided Design of structures, Shridevi Institute of Engineering and Technology,
Tumakuru, Karnataka, India
2Assistant Professor, Department of Civil Engineering, Shridevi Institute of Engineering and Technology,
3Professor, Department of Civil Engineering, Shridevi Institute of Engineering and Technology,
4Structural Engineer, SSC R and D Centre Bangalore, Karnataka, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - In high and medium rise structures to resist
lateral forces, coupled shear walls are one of the systems
commonly used. In multistory building should not collapse
or is induced severe damage during earthquake actions so,
for this reason coupled shear walls are used. It should be
having high strength, high ductility, high energy absorption
capacity and high shear stiffness to limit lateral
deformations. In the project, the building with without
coupled shear wall is considered and the same building is
with coupled by two shear wall with including flat slab with
drop panel in Soft Soil Condition with different seismic zone
condition is considered, then compare the behavior of these
buildings are studied. Analysis is done by using ETABS
software for static and dynamic case.
Key Words: Coupled Shear wall, Flat Slab with drop,
Storey Displacement, Storey Drift, Base Shear, Time
Period and ETABS.
1 INTRODUCTION
Building is a structure in which, it consists of wall and
roof. Where there are presents more or less permanently
in level surface, as house or factory. Building having so
many verities like shape, size and function. Has been
consider throughout the history for a huge no of factor
from building materials available, ground conditions,
specific uses and aesthetic reasons
A multi-story building are supports two or more floors
above ground. There is no formal restriction the height of
such a building or the member of floors a multi story
building may contain, through taller building do face more
practical difficulties.
1.1 Seismic Load
In General Dynamic motions are occurred when the
building is subject to earthquake. Inertia force acts to the
building in opposite towards the acceleration of
earthquake excitation there inertia force is called seismic
loads, terms like time and space where seismic loads are
not constant. Maximum storey shear force is consider,
where it act as a most influential to the static loads give
maximum storey shear force for each floor
1.2 Wind Load
Wind load is a one of the type of lateral load; the positive
or negative force of the wind acting on a structure, wind
applies a positive pressure on the windward side of
building and a negative suction to the leeward side. Wind
load can appear in any unexpected directions. Variations
of wind speed will be directly proportional to the
magnitude of the pressure that appears over the surface.
Here wind may appear either positive or negative
pressure where it will be influence by architectural plan or
design
1.3 Lateral Earth Pressure
It is the type of lateral loads in which, it is the pressure
that soil exerts in the horizontal direction. Its depends on
Shear strength characteristics of soil, Lateral strain
condition, Pore water pressure, State of equilibrium of soil
and wall and ground surface shape. Lateral earth pressure
say that below the ground there will be flow of water it
may appears the lateral pressure over the building.
Density of liquid is always directly proportional to the
lateral pressure.
1.4 Shea Wall
Shear wall are the structure use to resist lateral forces like
wind, seismic and lateral earth pressure. Shear wall are
commonly placed between column links, stair walls, lift
walls etc. It’s transferring the earthquake and wind load to
sub structure. During the earthquake happen there
generate waves which will effects over the surface of the
earth.

1.5 Coupled Shear Wall
It is a type of shear wall structure in which coupled by
using beam, it is also called core wall. It helps to reduce
the stress concentration from the structure where
sometime architecture plan needs opening in the shear
wall for doors and windows, so for stress concentration
will be more at surrounding of the opening we needs to
reduce this things by making solid shear wall system to
coupled shear wall system. Key parameter like stiffness
ratio in the coupling beam to wall piers, it makes the
degree of coupling between wall piers which cause the
system to acts as single unit.
1.6Flat Slab with Drop
It is a type of concrete slab in which this system where
beams are not present only column and slab system but in
outer edge there provide beam. Flat slab is noticed as one
sided or two sided support system, where the shear load
of the flat slab being concentrated over the supporting
columns and a square slab called drop panel, drop panel
acts as a major role in the flat slab system. Its helps to
increase stiffness of the floor, it develop the economical
span range. It helps to reduce cost of formwork. Flat slab
makes larger head room or shorter storey height.
1.7Coupling Beam
It is a member use to resisting later force; it couples or
combines two independent systems to make single unit.
This consequently decrease overturning effect and
improve overall stiffness of a system. The main function of
coupling beam is dissipation of energy and improving
stiffness and strength of the lateral load system of the
structure.
II. LITERATURE REVIEW
K.G. Patwari, et al, (2016) this paper highlights clearly
about, shear wall with flat slab gives stability to structure
as well as it improves lateral load resistance. Here
considered two models like conventional type building
and shear wall with flat slab building. Here G+9 and G+11
RC buildings are consider for analysis using ETABS
software with different parameters consider like, Base
shear, displacement, Time period. Time period is more for
conventional structure than flat slab structure because of
monolithic, displacement increase in case of flat slab
structure than conventional structure. As a result
structure with flat slab and shear wall sustain additional
and maximum load as redistribution reduces as the
number of member reduces in selected lateral load
resisting system.
B.Sowmya, et al, (2014) in this paper, author focus about
structural behavior affected by the size of the openings
and stress concentration around the openings and size of
the opening is directly relation with the depth of the
coupling beam. So, here consider G+9 storied building
using FES like ETABS. Consider the different size of
openings in shear wall and check there stress
concentration around the openings. Here, when the size of
the opening is increase simultaneously stress will be
increase, so openings are directly related with stress
concentration.
Reshma Chandran, et al, (2014) in this paper, author
going to say about comparative study over solid and
coupled shear wall system. Analysis was done by using
ETABS software with using different parameters like
storey shear, axial force in column, seismic base shear,
maximum deflection at roof level, lateral displacement at
each floor levels and time period, with different storey
levels like G+9, G+19, and G+ 39. Coupled shear wall is
more efficient in case of G+ 19 storeys; coupling beam
exhibits the maximum shear at the second floor.
Gummadi Amar, et al, (2014) in this paper, author focus
about RCC coupled shear wall using FEM, consider 10
storey’s for verifying and analyzing the same model by
using ANSYS-12 software. Here consider design
parameters like storey shear, storey displacement, lateral
force and von mises stress in steel also refer from IS 1893-
2002, In the FEA of coupled shear wall under structural
loading, the max deformation were observed for the top
surface of shear wall and its gradually reduced towards
the bottom, max stress are located at bottom of the shear
wall. Max lateral displacement at the top storey due to
lateral loads was in control and in limitations the check
calculated is safe. Dedicated element employed a creak
model to allow for concrete creaking with the option of
modeling the reinforcement in a distributed or discrete
manner. Shear wall is very effective to resist horizontal
forces coming from earthquake and wind forces etc.
Mohammad Hassan, et al, (2004) this paper focus on
seismic behavior of hybrid coupled wall system, where
steel beams used as coupling the reinforced concrete
shear walls analysis by pushover method, was defined in
FEMA-356(2000) using parameters like base shear,
storey drifts, wall rotations, shear distortion. Hybrid
coupled wall are well suited in high seismic risk, where
compare with normal one. Absorbing above lower roof
drifts, inter story drifts and wall rotations. The inter story
drift ratio from the pushover analysis (1%) is about 30%
of less than the median values from the dynamic runs
(1.43%).
III. DESCRIPTION OF SAMPLE BUILDING
In the study building models has been taken for all the
cases.

 Model having without coupled shear wall
with flat slab with drop
 Model having with coupled shear wall with
flat slab with drop
A 3D RC frames with 7 bay by 4 bay for 14 (G+13) stories
of dimension 77mx44m has been taken for seismic
analysis effect of without and with Coupled shear wall
using hard soil condition and seismic zones like II, III, IV, V
as per IS 1893 (part 1):2002.
IV. DESIGN DATA
Table 1 Geometric Property
Parameter Values
Number of storeys G+13
No. of bays in X direction 7
No. of bays in Y direction 4
Bay width in X direction 11m
Bay width in Y direction 11m
Storey height 4m
Slab thickness 0.25m
Drop thickness 0.45m
Main Beam size 1.1x1.3m
Coupling Beam size 0.3x1.5m
Column size 1.1x1.4m
Coupled shear wall size 1.25x0.3m &
1.5x0.3m
Table 2: Material Properties of concrete
Property Values
Grade of concrete M25, M30
Modulus of elasticity Ec = 5000√fck
Poisson’s ratio of concrete 0.2
Density of concrete 25kN/m3
Fig 1: Building plan for without coupled shear wall system
Fig 2: 3D View of without coupled shear wall system
Fig 3: Model elevation of without coupled shear wall
system
Fig 4: Building plan for with coupled shear wall system
Fig 5: 3D View of with coupled shear wall system
Fig 6: Model elevation of with coupled shear wall system
V. RESULT AND DISCUSSION
After completion of Analysis and modeling, the following
results are obtained Storey displacement, Storey drift,
Storey shear, Base shear and Modal time period.
STOREY DISPLACEMENT In Structure, lateral load effect
is studying by considering RC frame regular building with
and without coupled shear wall system, considering
different soil condition with different seismic zone
Table 3: Comparison on without and with shear wall
models with different soil strata and different seismic
zones
SOIL
STRATA
MODEL SEISMIC
ZONES
MAX
DISPLACE
MENT @
X-
AXIS(mm)
MAX
DISPLAC
EMENT
@ Y-
AXIS(m
m)
WITH
OUT
COUPLE
D SHEAR
Zone II 28.60 54.40
Zone III 45.70 87.10

Hard
Soil
WALL Zone IV 41.10 78.40
Zone V 61.70 117.6
WITH
COUPLE
D SHEAR
WALL
Zone II 22.70 36.90
Zone III 36.30 59.10
Zone IV 32.70 53.10
Zone V 49.20 80.10
Chart 1: Graph Showing No. of Storey’s V/S
Displacement for along X- Direction
Chart 2: Graph Showing Max Storey Displacement
along X - Direction
Displacement for along Y-Direction
along Y-Direction
Displacement for along X –Direction
along X – Direction
Displacement for along Y-Direction
along Y-Direction
Charts plotted from 1, 2, 3, & 4for (without shear wall) X &
Y axis and 5, 6, 7 & 8 for (with shear wall)X & Y – axis for
displacement v/s storey’s for in fill frame models for hard
soil strata with different seismic zones. Zone II and Zone
III for Elastic Static Analysis and zone IV and zone V for
Dynamic consider as per code IS 1983 2002 for 14 floors.
As per the condition, displacement will be gradually
increase from Zone II to Zone V, But here Zone IV will be
decreases from Zone III, so Zone IV will be more stiffness
then other Seismic Zones.

Storey Drift
To study the response of lateral load effect on structure
we used RC frame regular building with and without
coupled shear wall, considering different soil strata and
seismic zones.
SOIL
STRATA
MODEL SEISMIC
ZONES
MAX
STOREY
DRIFT
@ X-
AXIS (m)
MAX
STOREY
DRIFT
@ Y-
AXIS (m)
Hard Soil
WITH
OUT
COUPLE
D SHEAR
WALL
Zone II 0.0006 0.0012
Zone III 0.0010 0.0020
Zone IV 0.0009 0.0018
Zone V 0.0013 0.0027
WITH
COUPLE
D SHEAR
WALL
Zone II 0.0004 0.0008
Zone III 0.0007 0.0013
Zone IV 0.0007 0.0011
Zone V 0.0010 0.0018
Chart 9: Graph Showing No. of Storey’s V/S Drift for
along X –Direction
Chart 10: Graph Showing Max Storey Drift along x –
Direction
along Y- Direction
Chart 12: Graph Showing Max Storey Drift along Y -
Direction
along X –Direction
Chart 14: Graph Showing Max Storey Drift along x -
Direction
along Y- Direction

Chart 16: Graph Showing Max Storey Drift along Y -
Direction
Charts plotted from 9,10,11,12 for (without shear wall) X
& Y axis and 13, 14, 15 & 16 for (with shear wall)X & Y
axis for Storey drift v/s storey’s for in fill frame models for
hard soil strata with different seismic zones. Zone II and
Zone III for Elastic Static Analysis and zone IV and zone V
for Dynamic consider as per code IS 1983 2002 for 14
floors. As per the condition, displacement will be gradually
increase from Zone II to Zone V. But here Zone IV will be
decreases from Zone III, so Zone IV will be more stiffness
then other Seismic Zones.
Base Shear
SOIL
STRATA
MODEL SEISMIC
ZONES
MAX
Base
Shear @
X –
Directio
n (mm)
MAX
Base
Shear @
Y –
Directio
n (mm)
Hard
Soil
WITH
OUT
COUPLE
D SHEAR
WALL
Zone II 15672 15672
Zone III 25098 25098
Zone IV 22584 22584
Zone V 33877 33877
WITH
COUPLE
D SHEAR
WALL
Zone II 15203 15203
Zone III 24325 24325
Zone IV 21893 21893
Zone V 32989 32989
Chart 17: Graph Showing Maximum Base Shear @
X and Y- direction (without coupled shear wall)
Chart 18: Graph Showing Maximum Base Shear @ X
and Y- direction(with coupled shear wall)
Chart from 17 and 18, indicates the comparison of base
shear values for models in X and Y-Direction (Without
and With Coupled Shear wall). The maximum shear will
be acting at the top storey. From the figure base shear will
be more at Zone V. In generally base shear will be
gradually increased, but here Zone IV will be decrease
from Zone III. In Zone III with hard Soil Condition it will be
more Stiffness than other Zone. Here we consider that
regular shape models so base shear value will be same in
both X and Y direction.
Model Time Period
MODE WITHOUT
COUPLED SHEAR
WALLPERIOD
(Sec)
WITH COUPLED
SHEAR WALL
PERIOD (Sec)
1 2.47 2.00
2 1.77 1.56
3 1.56 1.16
4 0.76 0.61
5 0.54 0.48
6 0.49 0.37
7 0.40 0.32
8 0.29 0.25
9 0.27 0.20
10 0.25 0.20
11 0.19 0.17
12 0.18 0.14
Chart 19: Graph showing time periods v/s No of modes
for Hard Soil Strata for 14 floors

VI. CONCLUSION
In the present study an attempt has been to check the
performance of high rise infill frame building for without
coupled and with coupled shear wall with Hard soil
condition and also different seismic zones. Here we
consider that 14 storey’s model for zone II, zone III
condition we consider elastic static analysis and zone IV
and zone V for dynamic analysis (by Response spectrum
method) are carried out to compare the results.
 In with coupled shear wall model, there is a
considerable reduction in storey displacement,
storey drift, base shear and also time period
compare with without coupled shear wall model
 As per IS code, there will be increasing value from
zone II to zone V, but here zone IV will be
decrease from zone III. In zone IV will be more
stiffness than other zone models.
 Maximum lateral storey displacement occur at
terrace floor level for all types of structure
(without coupled and with coupled shear wall)
 Average displacement of with coupled shear wall
building along x-direction is 79.72% less
compared to without coupled shear wall building
and along Y-direction is 67.89% less compared to
without coupled shear wall building.
 Maximum Storey drift usually occurs at mid
height level and goes on decreasing from mid
height towards roof level
 Storey drift, with coupled shear wall system along
x-direction is 21.37% less then without coupled
shear wall system
 Storey drift, with coupled shear wall system along
Y-direction is 35.35% less then without coupled
shear wall system
 Maximum Base Shear occurs at base level due to
direct ground contact of the structure
 There is an increase in base shear of 2.63% for
with coupled shear wall structure with without
coupled shear wall structure
 For without coupled shear wall and with coupled
shear wall from hard soil to soft soil the % in base
shear is 59.80%.
VII. REFERENCES
1. Nam Shiu, M. ASCE, T. Takayanagi, and W. Gene
Corley, F. ASCE, Seismic Behavior Of Coupled Wall
Systems, American Society of Civil Engineers, pp-
1-16.1984
2. Dipendu Bhunia, Vipul Prakash, and Ashok D.
Pandey. A Conceptual Design Approach of
Coupled Shear Walls, ISRN Civil Engineering, pp-
1-29.2013.
3. Medhekar,m.s., and jain, s.k., “seismic behavior,
design and detailing of RC shear walls, Part II :
Design and detailing” , The Indian Concrete
Journal, Pages : 451-457,1993.
4. S.K. Duggal in his,“Earth quake resistant design of
structures”, pp. 301, 8.12 about Shear walls.
5. S.K. Duggal in his,“Earth quake resistant design of
structures”, pp. 305, 8.14.1 (case: 1, case: 2) about
flexural strength.

Comparative Study on Dynamic Behaviour of Multi-Storey Building with and Without Coupled Shear Wall System

More Related Content

What's hot (20)

Similar to Comparative Study on Dynamic Behaviour of Multi-Storey Building with and Without Coupled Shear Wall System (20)

More from IRJET Journal (20)

Recently uploaded (20)

Comparative Study on Dynamic Behaviour of Multi-Storey Building with and Without Coupled Shear Wall System