Configuracion

C H A P T E R 15
Configuring STP

This chapter describes how to configure the Spanning Tree Protocol (STP) on port-based VLANs on
your Catalyst 3550 switch. The switch can use either the per-VLAN spanning-tree plus (PVST+)
protocol based on the IEEE 802.1D standard and Cisco proprietary extensions, or the rapid per-VLAN
spanning-tree plus (rapid-PVST+) protocol based on the IEEE 802.1w standard.
For information about the Multiple Spanning Tree Protocol (MSTP) and how to map multiple VLANs
to the same spanning-tree instance, see Chapter 16, “Configuring MSTP.”
For information about other spanning-tree features such as Port Fast, UplinkFast, root guard, and so
forth, see Chapter 17, “Configuring Optional Spanning-Tree Features.”

Note For complete syntax and usage information for the commands used in this chapter, see the command
reference for this release.

This chapter consists of these sections:
• Understanding Spanning-Tree Features, page 15-1
• Configuring Spanning-Tree Features, page 15-11
• Displaying the Spanning-Tree Status, page 15-24

Understanding Spanning-Tree Features
These sections describe how basic spanning-tree features work:
• STP Overview, page 15-2
• Spanning-Tree Topology and BPDUs, page 15-2
• Bridge ID, Switch Priority, and Extended System ID, page 15-3
• Spanning-Tree Interface States, page 15-4
• How a Switch or Port Becomes the Root Switch or Root Port, page 15-7
• Spanning Tree and Redundant Connectivity, page 15-7
• Spanning-Tree Address Management, page 15-8
• Accelerated Aging to Retain Connectivity, page 15-8
• Spanning-Tree Modes and Protocols, page 15-9
• Supported Spanning-Tree Instances, page 15-9

Catalyst 3550 Multilayer Switch Software Configuration Guide
OL-8565-01 15-1

Chapter 15 Configuring STP

• Spanning-Tree Interoperability and Backward Compatibility, page 15-10
• STP and IEEE 802.1Q Trunks, page 15-10
• VLAN-Bridge Spanning Tree, page 15-11
For configuration information, see the “Configuring Spanning-Tree Features” section on page 15-11.
For information about optional spanning-tree features, see Chapter 17, “Configuring Optional
Spanning-Tree Features.”

STP Overview
STP is a Layer 2 link management protocol that provides path redundancy while preventing loops in the
network. For a Layer 2 Ethernet network to function properly, only one active path can exist between
any two stations. Multiple active paths among end stations cause loops in the network. If a loop exists
in the network, end stations might receive duplicate messages. Switches might also learn end-station
MAC addresses on multiple Layer 2 interfaces. These conditions result in an unstable network.
Spanning-tree operation is transparent to end stations, which cannot detect whether they are connected
to a single LAN segment or a switched LAN of multiple segments.
The STP uses a spanning-tree algorithm to select one switch of a redundantly connected network as the
root of the spanning tree. The algorithm calculates the best loop-free path through a switched Layer 2
network by assigning a role to each port based on the role of the port in the active topology:
• Root—A forwarding port elected for the spanning-tree topology
• Designated—A forwarding port elected for every switched LAN segment
• Alternate—A blocked port providing an alternate path to the root bridge in the spanning tree
• Backup—A blocked port in a loopback configuration
The switch that has all of its ports as the designated role or as the backup role is the root switch. The
switch that has at least one of its ports in the designated role is called the designated switch.
Spanning tree forces redundant data paths into a standby (blocked) state. If a network segment in the
spanning tree fails and a redundant path exists, the spanning-tree algorithm recalculates the
spanning-tree topology and activates the standby path. Switches send and receive spanning-tree frames,
called bridge protocol data units (BPDUs), at regular intervals. The switches do not forward these frames
but use them to construct a loop-free path. BPDUs contain information about the sending switch and its
ports, including switch and MAC addresses, switch priority, port priority, and path cost. Spanning tree
uses this information to elect the root switch and root port for the switched network and the root port
and designated port for each switched segment.
When two interfaces on a switch are part of a loop, the spanning-tree port priority and path cost settings
determine which interface is put in the forwarding state and which is put in the blocking state. The
spanning-tree port priority value represents the location of an interface in the network topology and how
well it is located to pass traffic. The path cost value represents the media speed.

Spanning-Tree Topology and BPDUs
The stable, active spanning-tree topology of a switched network is determined by these elements:
• The unique bridge ID (switch priority and MAC address) associated with each VLAN on each
switch
• The spanning-tree path cost to the root switch

15-2 OL-8565-01


• The port identifier (port priority and MAC address) associated with each Layer 2 interface
When the switches in a network are powered up, each functions as the root switch. Each switch sends a
configuration BPDU through all of its ports. The BPDUs communicate and compute the spanning-tree
topology. Each configuration BPDU contains this information:
• The unique bridge ID of the switch that the sending switch identifies as the root switch
• The spanning-tree path cost to the root
• The bridge ID of the sending switch
• Message age
• The identifier of the sending interface
• Values for the hello, forward-delay, and max-age protocol timers
When a switch receives a configuration BPDU that contains superior information (lower bridge ID,
lower path cost, and so forth), it stores the information for that port. If this BPDU is received on the root
port of the switch, the switch also forwards it with an updated message to all attached LANs for which
it is the designated switch.
If a switch receives a configuration BPDU that contains inferior information to that currently stored for
that port, it discards the BPDU. If the switch is a designated switch for the LAN from which the inferior
BPDU was received, it sends that LAN a BPDU containing the up-to-date information stored for that
port. In this way, inferior information is discarded, and superior information is propagated on the
network.
A BPDU exchange results in these actions:
• One switch in the network is elected as the root switch (the logical center of the spanning-tree
topology in a switched network).
For each VLAN, the switch with the highest switch priority (the lowest numerical priority value) is
elected as the root switch. If all switches are configured with the default priority (32768), the switch
with the lowest MAC address in the VLAN becomes the root switch. The switch priority value
occupies the most significant bits of the bridge ID, as shown in Table 15-1 on page 15-4.
• A root port is selected for each switch (except the root switch). This port provides the best path
(lowest cost) when the switch forwards packets to the root switch.
• The shortest distance to the root switch is calculated for each switch based on the path cost.
• A designated switch for each LAN segment is selected. The designated switch incurs the lowest path
cost when forwarding packets from that LAN to the root switch. The port through which the
designated switch is attached to the LAN is called the designated port.
• Interfaces included in the spanning-tree instance are selected. Root ports and designated ports are
put in the forwarding state.
• All paths that are not needed to reach the root switch from anywhere in the switched network are
placed in the spanning-tree blocking mode.

Bridge ID, Switch Priority, and Extended System ID
The IEEE 802.1D standard requires that each switch has an unique bridge identifier (bridge ID), which
determines the selection of the root switch. Because each VLAN is considered as a different logical
bridge with PVST+ and rapid PVST+, the same switch must have as many different bridge IDs as
VLANs configured on it. Each VLAN on the switch has a unique 8-byte bridge ID; the two
most-significant bytes are used for the switch priority, and the remaining six bytes are derived from the
switch MAC address.

OL-8565-01 15-3


In Cisco IOS Release 12.1(8)EA1 and later, the switch supports the 802.1t spanning-tree extensions.
Some of the bits previously used for the switch priority are now used as the VLAN identifier. The result
is that fewer MAC addresses are reserved for the switch, and a larger range of VLAN IDs can be
supported, all while maintaining the uniqueness of the bridge ID. As shown in Table 15-1, the two bytes
previously used for the switch priority are reallocated into a 4-bit priority value and a 12-bit extended
system ID value equal to the VLAN ID. In earlier releases, the switch priority is a 16-bit value.

Table 15-1 Switch Priority Value and Extended System ID

Switch Priority Value Extended System ID (Set Equal to the VLAN ID)
Bit 16 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
32768 16384 8192 4096 2048 1024 512 256 128 64 32 16 8 4 2 1

Spanning tree uses the extended system ID, the switch priority, and the allocated spanning-tree MAC
address to make the bridge ID unique for each VLAN. With earlier releases, spanning tree used one MAC
address per VLAN to make the bridge ID unique for each VLAN.
Support for the extended system ID affects how you manually configure the root switch, the secondary
root switch, and the switch priority of a VLAN. For example, when you change the switch priority value,
you change the probability that the switch will be elected as the root switch. Configuring a higher value
decreases the probability; a lower value increases the probability. For more information, see the
“Configuring the Root Switch” section on page 15-14, the “Configuring a Secondary Root Switch”
section on page 15-16, and the “Configuring the Switch Priority of a VLAN” section on page 15-20.

Spanning-Tree Interface States
Propagation delays can occur when protocol information passes through a switched LAN. As a result,
topology changes can take place at different times and at different places in a switched network. When
an interface transitions directly from nonparticipation in the spanning-tree topology to the forwarding
state, it can create temporary data loops. Interfaces must wait for new topology information to propagate
through the switched LAN before starting to forward frames. They must allow the frame lifetime to
expire for forwarded frames that have used the old topology.
Each Layer 2 interface on a switch using spanning tree exists in one of these states:
• Blocking—The interface does not participate in frame forwarding.
• Listening—The first transitional state after the blocking state when the spanning tree determines
that the interface should participate in frame forwarding.
• Learning—The interface prepares to participate in frame forwarding.
• Forwarding—The interface forwards frames.
• Disabled—The interface is not participating in spanning tree because of a shutdown port, no link on
the port, or no spanning-tree instance running on the port.
An interface moves through these states:
• From initialization to blocking
• From blocking to listening or to disabled
• From listening to learning or to disabled
• From learning to forwarding or to disabled
• From forwarding to disabled

15-4 OL-8565-01


Figure 15-1 illustrates how an interface moves through the states.

Figure 15-1 Spanning-Tree Interface States

Power-on
initialization

Blocking
state

Listening Disabled
state state

Learning
state

Forwarding
43569

state

When you power up the switch, spanning tree is enabled by default, and every interface in the switch,
VLAN, or network goes through the blocking state and the transitory states of listening and learning.
Spanning tree stabilizes each interface at the forwarding or blocking state.
When the spanning-tree algorithm places a Layer 2 interface in the forwarding state, this process occurs:
1. The interface is in the listening state while spanning tree waits for protocol information to transition
the interface to the blocking state.
2. While the spanning tree waits for the forward-delay timer to expire, it moves the interface to the
learning state and resets the forward-delay timer.
3. In the learning state, the interface continues to block frame forwarding as the switch learns
end-station location information for the forwarding database.
4. When the forward-delay timer expires, spanning tree moves the interface to the forwarding state,
where both learning and frame forwarding are enabled.

Blocking State
A Layer 2 interface in the blocking state does not participate in frame forwarding. After initialization, a
BPDU is sent to each interface in the switch. A switch initially functions as the root until it exchanges
BPDUs with other switches. This exchange establishes which switch in the network is the root or root
switch. If there is only one switch in the network, no exchange occurs, the forward-delay timer expires,
and the interfaces move to the listening state. An interface always enters the blocking state after switch
initialization.
An interface in the blocking state performs as follows:
• Discards frames received on the port
• Discards frames switched from another interface for forwarding
• Does not learn addresses
• Receives BPDUs

OL-8565-01 15-5


Listening State
The listening state is the first state a Layer 2 interface enters after the blocking state. The interface enters
this state when the spanning tree determines that the interface should participate in frame forwarding.
An interface in the listening state performs as follows:
• Receives BPDUs

Learning State
A Layer 2 interface in the learning state prepares to participate in frame forwarding. The interface enters
the learning state from the listening state.
An interface in the learning state performs as follows:
• Learns addresses
• Receives BPDUs

Forwarding State
A Layer 2 interface in the forwarding state forwards frames. The interface enters the forwarding state
from the learning state.
An interface in the forwarding state performs as follows:
• Receives and forwards frames received on the port
• Forwards frames switched from another port
• Learns addresses
• Receives BPDUs

Disabled State
A Layer 2 interface in the disabled state does not participate in frame forwarding or in the spanning tree.
An interface in the disabled state is nonoperational.
A disabled interface performs as follows:
• Does not receive BPDUs

15-6 OL-8565-01


How a Switch or Port Becomes the Root Switch or Root Port
If all switches in a network are enabled with default spanning-tree settings, the switch with the lowest
MAC address becomes the root switch. In Figure 15-2, Switch A is elected as the root switch because
the switch priority of all the switches is set to the default (32768) and Switch A has the lowest MAC
address. However, because of traffic patterns, number of forwarding interfaces, or link types, Switch A
might not be the ideal root switch. By increasing the priority (lowering the numerical value) of the ideal
switch so that it becomes the root switch, you force a spanning-tree recalculation to form a new topology
with the ideal switch as the root.

Figure 15-2 Spanning-Tree Topology

DP
DP DP
A D
DP RP

RP RP DP
86475
B C

RP = Root Port
DP = Designated Port

When the spanning-tree topology is calculated based on default parameters, the path between source and
destination end stations in a switched network might not be ideal. For instance, connecting higher-speed
links to an interface that has a higher number than the root port can cause a root-port change. The goal
is to make the fastest link the root port.
For example, assume that one port on Switch B is a Gigabit Ethernet link and that another port on
Switch B (a 10/100 Mbps link) is the root port. Network traffic might be more efficient over the Gigabit
Ethernet link. By changing the spanning-tree port priority on the Gigabit Ethernet interface to a higher
priority (lower numerical value) than the root port, the Gigabit Ethernet interface becomes the new root
port.

Spanning Tree and Redundant Connectivity
You can create a redundant backbone with spanning tree by connecting two switch interfaces to another
device or to two different devices. Spanning tree automatically disables one interface but enables it if
the other one fails, as shown in Figure 15-3. If one link is high-speed and the other is low-speed, the
low-speed link is always disabled. If the speeds are the same, the port priority and port ID are added
together, and spanning tree disables the link with the lowest value.

OL-8565-01 15-7


Figure 15-3 Spanning Tree and Redundant Connectivity

Active link

101226
Blocked link
Workstations

You can also create redundant links between switches by using EtherChannel groups. For more
information, see Chapter 31, “Configuring EtherChannels.”

Spanning-Tree Address Management
IEEE 802.1D specifies 17 multicast addresses, ranging from 0x00180C2000000 to 0x0180C2000010, to
be used by different bridge protocols. These addresses are static addresses that cannot be removed.
Regardless of the spanning-tree state, the switch receives but does not forward packets destined for
addresses between 0x0180C2000000 and 0x0180C200000F.
If spanning tree is enabled, the switch CPU receives packets destined for 0x0180C2000000 and
0x0180C2000010. If spanning-tree is disabled, the switch forwards those packets as unknown multicast
addresses.

Accelerated Aging to Retain Connectivity
The default for aging dynamic addresses is 5 minutes, the default setting of the mac-address-table
aging-time global configuration command. However, a spanning-tree reconfiguration can cause many
station locations to change. Because these stations could be unreachable for 5 minutes or more during a
reconfiguration, the address-aging time is accelerated so that station addresses can be dropped from the
address table and then relearned. The accelerated aging is the same as the forward-delay parameter value
(spanning-tree vlan vlan-id forward-time seconds global configuration command) when the spanning
tree reconfigures.
Because each VLAN is a separate spanning-tree instance, the switch accelerates aging on a per-VLAN
basis. A spanning-tree reconfiguration on one VLAN can cause the dynamic addresses learned on that
VLAN to be subject to accelerated aging. Dynamic addresses on other VLANs can be unaffected and
remain subject to the aging interval entered for the switch.

15-8 OL-8565-01


Spanning-Tree Modes and Protocols
The switch supports these spanning-tree modes and protocols:
PVST+—This spanning-tree mode is based on the IEEE 802.1D standard and Cisco proprietary
extensions. It is the default spanning-tree mode used on all Ethernet, Fast Ethernet, and Gigabit
Ethernet port-based VLANs. The PVST+ runs on each VLAN on the switch up to the maximum
supported, ensuring that each has a loop-free path through the network.
The PVST+ provides Layer 2 load balancing for the VLAN on which it runs. You can create
different logical topologies by using the VLANs on your network to ensure that all of your links are
used but that no one link is oversubscribed. Each instance of PVST+ on a VLAN has a single root
switch. This root switch propagates the spanning-tree information associated with that VLAN to all
other switches in the network. Because each switch has the same information about the network, this
process ensures that the network topology is maintained.
• Rapid PVST+—This spanning-tree mode is the same as PVST+ except that is uses a rapid
convergence based on the IEEE 802.1w standard. To provide rapid convergence, the rapid PVST+
immediately deletes dynamically learned MAC address entries on a per-port basis upon receiving a
topology change. By contrast, PVST+ uses a short aging time for dynamically learned MAC address
entries.
The rapid PVST+ uses the same configuration as PVST+ (except where noted), and the switch needs
only minimal extra configuration. The benefit of rapid PVST+ is that you can migrate a large PVST+
install base to rapid PVST+ without having to learn the complexities of the MSTP configuration and
without having to reprovision your network. In rapid-PVST+ mode, each VLAN runs its own
spanning-tree instance up to the maximum supported.
• MSTP—This spanning-tree mode is based on the IEEE 802.1s standard. You can map multiple
VLANs to the same spanning-tree instance, which reduces the number of spanning-tree instances
required to support a large number of VLANs. The MSTP runs on top of the RSTP (based on IEEE
802.1w, which provides for rapid convergence of the spanning tree by eliminating the forward delay
and by quickly transitioning root ports and designated ports to the forwarding state. You cannot run
MSTP without RSTP.
The most common initial deployment of MSTP is in the backbone and distribution layers of a
Layer 2 switched network. For more information, see Chapter 16, “Configuring MSTP.” For
information about the number of supported spanning-tree instances, see the next section.

Supported Spanning-Tree Instances
In PVST+ or rapid-PVST+ mode, the switch supports up to 128 spanning-tree instances.
In MSTP mode, the switch supports up to 65 MST instances. The number of VLANs that can be mapped
to a particular MST instance is unlimited.
For information about how spanning tree interoperates with the VLAN Trunking Protocol (VTP), see the
“Spanning-Tree Configuration Guidelines” section on page 15-12.

OL-8565-01 15-9


Spanning-Tree Interoperability and Backward Compatibility
Table 15-2 lists the interoperability and compatibility among the supported spanning-tree modes in a
network.

Table 15-2 PVST+, MSTP and Rapid-PVST+ Interoperability
,

PVST+ MSTP Rapid PVST+
PVST+ Yes Yes (with restrictions) Yes (reverts to PVST+)
MSTP Yes (with restrictions) Yes Yes (reverts to PVST+)
Rapid PVST+ Yes (reverts to PVST+) Yes (reverts to PVST+) Yes

In a mixed MSTP and PVST+ network, the common spanning-tree (CST) root must be inside the MST
backbone, and a PVST+ switch cannot connect to multiple MST regions.
When a network contains switches running rapid PVST+ and switches running PVST+, we recommend
that the rapid-PVST+ switches and PVST+ switches be configured for different spanning-tree instances.
In the rapid-PVST+ spanning-tree instances, the root switch must be a rapid-PVST+ switch. In the
PVST+ instances, the root switch must be a PVST+ switch. The PVST+ switches should be at the edge
of the network.

STP and IEEE 802.1Q Trunks
The IEEE 802.1Q standard for VLAN trunks imposes some limitations on the spanning-tree strategy for
a network. The standard requires only one spanning-tree instance for all VLANs allowed on the trunks.
However, in a network of Cisco switches connected through IEEE 802.1Q trunks, the switches maintain
one spanning-tree instance for each VLAN allowed on the trunks.
When you connect a Cisco switch to a non-Cisco device through an IEEE 802.1Q trunk, the Cisco switch
uses PVST+ to provide spanning-tree interoperability. If rapid PVST+ is enabled, the switch uses it
instead of PVST+. The switch combines the spanning-tree instance of the IEEE 802.1Q VLAN of the
trunk with the spanning-tree instance of the non-Cisco IEEE 802.1Q switch.
However, all PVST+ or rapid-PVST+ information is maintained by Cisco switches separated by a cloud
of non-Cisco IEEE 802.1Q switches. The non-Cisco IEEE 802.1Q cloud separating the Cisco switches
is treated as a single trunk link between the switches.
PVST+ is automatically enabled on 802.1Q trunks, and no user configuration is required. The external
spanning-tree behavior on access ports and Inter-Switch Link (ISL) trunk ports is not affected by
PVST+.
For more information on IEEE 802.1Q trunks, see Chapter 11, “Configuring VLANs.”

15-10 OL-8565-01

Configuring Spanning-Tree Features

VLAN-Bridge Spanning Tree
Cisco VLAN-bridge spanning tree is used with the fallback bridging feature (bridge groups), which
forwards non-IP protocols such as DECnet between two or more VLAN bridge domains or routed ports.
The VLAN-bridge spanning tree allows the bridge groups to form a spanning tree on top of the
individual VLAN spanning trees to prevent loops from forming if there are multiple connections among
VLANs. It also prevents the individual spanning trees from the VLANs being bridged from collapsing
into a single spanning tree.
To support VLAN-bridge spanning tree, some of the spanning-tree timers are increased. To use the
fallback bridging feature, you must have the enhanced multilayer software image installed on your
switch. For more information, see Chapter 37, “Configuring Fallback Bridging.”

These sections describe how to configure spanning-tree features:
• Default Spanning-Tree Configuration, page 15-11
• Spanning-Tree Configuration Guidelines, page 15-12
• Changing the Spanning-Tree Mode, page 15-13 (required)
• Disabling Spanning Tree, page 15-14 (optional)
• Configuring the Root Switch, page 15-14 (optional)
• Configuring a Secondary Root Switch, page 15-16 (optional)
• Configuring the Port Priority, page 15-17 (optional)
• Configuring the Path Cost, page 15-18 (optional)
• Configuring the Switch Priority of a VLAN, page 15-20 (optional)
• Configuring Spanning-Tree Timers, page 15-20 (optional)

Default Spanning-Tree Configuration
Table 15-3 shows the default spanning-tree configuration.

Table 15-3 Default Spanning-Tree Conﬁguration

Feature Default Setting
Enable state Enabled on VLAN 1.
For more information, see the “Supported
Spanning-Tree Instances” section on
page 15-9.
Spanning-tree mode PVST+. (Rapid PVST+ and MSTP are
disabled.)
Switch priority 32768.
Spanning-tree port priority (configurable on a per-interface basis) 128.

OL-8565-01 15-11


Table 15-3 Default Spanning-Tree Conﬁguration (continued)

Feature Default Setting
Spanning-tree port cost (configurable on a per-interface basis) 1000 Mbps: 4.
100 Mbps: 19.
10 Mbps: 100.
Spanning-tree VLAN port priority (configurable on a per-VLAN basis) 128.
Spanning-tree VLAN port cost (configurable on a per-VLAN basis) 1000 Mbps: 4.
100 Mbps: 19.
10 Mbps: 100.
Spanning-tree timers Hello time: 2 seconds.
Forward-delay time: 15 seconds.
Maximum-aging time: 20 seconds.
Transmit hold count: 6 BPDUs

Spanning-Tree Configuration Guidelines
If more VLANs are defined in the VTP than there are spanning-tree instances, you can enable PVST+
or rapid PVST+ on only 128 VLANs. The remaining VLANs operate with spanning tree disabled. If the
number of VLANs exceeds 128, we recommend that you enable the MSTP to map multiple VLANs to
a single spanning-tree instance. For more information, see Chapter 16, “Configuring MSTP.”
For information on the recommended trunk port configuration, see the“Interaction with Other Features”
section on page 11-19.
If 128 instances of spanning tree are already in use, you can disable spanning tree on one of the VLANs
and then enable it on the VLAN where you want it to run. Use the no spanning-tree vlan vlan-id global
configuration command to disable spanning tree on a specific VLAN, and use the spanning-tree vlan
vlan-id global configuration command to enable spanning tree on the desired VLAN.

Caution Switches that are not running spanning tree still forward received BPDUs so that the other switches on
the VLAN with a running spanning-tree instance can break loops. Therefore, spanning tree must be
running on enough switches to break all the loops in the network. For example, at least one switch on
each loop in the VLAN must be running spanning tree. It is not absolutely necessary to run spanning tree
on all switches in the VLAN; however, if you are running spanning tree only on a minimal set of
switches, an incautious change to the network that introduces another loop into the VLAN can result in
a broadcast storm.

Note If you have already used all available spanning-tree instances on your switch, adding another VLAN
anywhere in the VTP domain creates a VLAN that is not running spanning tree on that switch. If you
have the default allowed list on the trunk ports of that switch, the new VLAN is carried on all trunk ports.
Depending on the topology of the network, this could create a loop in the new VLAN that will not be
broken, particularly if there are several adjacent switches that have all run out of spanning-tree instances.
You can prevent this possibility by setting up allowed lists on the trunk ports of switches that have used
up their allocation of spanning-tree instances. Setting up allowed lists is not necessary in many cases and
can make it more labor-intensive to add another VLAN to the network.

15-12 OL-8565-01


Spanning-tree commands determine the configuration of VLAN spanning-tree instances. You create a
spanning-tree instance when you assign an interface to a VLAN. The spanning-tree instance is removed
when the last interface is moved to another VLAN. You can configure switch and port parameters before
a spanning-tree instance is created; these parameters are applied when the spanning-tree instance is
created.
The switch supports PVST+, rapid PVST+, and MSTP, but only one version can be active at any time.
(For example, all VLANs run PVST+, all VLANs run rapid PVST+, or all VLANs run MSTP.) For
information about the different spanning-tree modes and how they interoperate, see the “Spanning-Tree
Interoperability and Backward Compatibility” section on page 15-10.
For configuration guidelines about UplinkFast, BackboneFast, and cross-stack UplinkFast, see the
“Optional Spanning-Tree Configuration Guidelines” section on page 17-14.

Changing the Spanning-Tree Mode
The switch supports three spanning-tree modes: PVST+, rapid PVST+, or MSTP. By default, the switch
runs the PVST+ protocol.
Beginning in privileged EXEC mode, follow these steps to change the spanning-tree mode. If you want
to enable a mode that is different from the default mode, this procedure is required.

Command Purpose
Step 1 configure terminal Enter global configuration mode.
Step 2 spanning-tree mode {pvst | mst | Configure a spanning-tree mode.
rapid-pvst} • Select pvst to enable PVST+ (the default setting).
• Select mst to enable MSTP (and RSTP). For more configuration
steps, see Chapter 16, “Configuring MSTP.”
• Select rapid-pvst to enable rapid PVST+.
Step 3 interface interface-id (Recommended for rapid-PVST+ mode only) Specify an interface to
configure, and enter interface configuration mode. Valid interfaces
include physical ports, VLANs, and port channels. Valid VLAN IDs are
1 to 4094. The port-channel range is 1 to 64.
Step 4 spanning-tree link-type point-to-point (Recommended for rapid-PVST+ mode only) Specify that the link type
for this port is point-to-point.
If you connect this port (local port) to a remote port through a
point-to-point link and the local port becomes a designated port, the
switch negotiates with the remote port and rapidly transitions the local
port to the forwarding state.
Step 5 end Return to privileged EXEC mode.
Step 6 clear spanning-tree detected-protocols (Recommended for rapid-PVST+ mode only) If any port on the switch
is connected to a port on a legacy IEEE 802.1D switch, restart the
protocol migration process on the entire switch.
This step is optional if the designated switch determines that this switch
is running rapid PVST+.

OL-8565-01 15-13


Command Purpose
Step 7 show spanning-tree summary Verify your entries.
and
show spanning-tree interface
interface-id
Step 8 copy running-config startup-config (Optional) Save your entries in the configuration file.

To return to the default setting, use the no spanning-tree mode global configuration command. To return
the port to its default setting, use the no spanning-tree link-type interface configuration command.

Disabling Spanning Tree
Spanning tree is enabled by default on VLAN 1 and on all newly created VLANs up to the spanning-tree
limit specified in the “Supported Spanning-Tree Instances” section on page 15-9. Disable spanning tree
only if you are sure there are no loops in the network topology.

Caution When spanning tree is disabled and loops are present in the topology, excessive traffic and indefinite
packet duplication can drastically reduce network performance.

Beginning in privileged EXEC mode, follow these steps to disable spanning tree on a per-VLAN basis.
This procedure is optional.

Command Purpose
Step 2 no spanning-tree vlan vlan-id Disable spanning tree on a per-VLAN basis.
For vlan-id, you can specify a single VLAN identified by VLAN ID
number, a range of VLANs separated by a hyphen, or a series of VLANs
separated by a comma. The range is 1 to 4094.
Step 4 show spanning-tree vlan vlan-id Verify your entries.

To re-enable spanning tree, use the spanning-tree vlan vlan-id global configuration command.

Configuring the Root Switch
The switch maintains a separate spanning-tree instance for each active VLAN configured on it. A bridge
ID, consisting of the switch priority and the switch MAC address, is associated with each instance. For
each VLAN, the switch with the lowest bridge ID becomes the root switch for that VLAN.
To configure a switch to become the root for the specified VLAN, use the spanning-tree vlan vlan-id
root global configuration command to modify the switch priority from the default value (32768) to a
significantly lower value. When you enter this command, the switch checks the switch priority of the

15-14 OL-8565-01


root switches for each VLAN. Because of the extended system ID support, the switch sets its own
priority for the specified VLAN to 24576 if this value will cause this switch to become the root for the
specified VLAN.
If any root switch for the specified VLAN has a switch priority lower than 24576, the switch sets its own
priority for the specified VLAN to 4096 less than the lowest switch priority. (4096 is the value of the
least-significant bit of a 4-bit switch priority value as shown in Table 15-1 on page 15-4.)

Note The spanning-tree vlan vlan-id root global configuration command fails if the value necessary to be the
root switch is less than 1.

Before Cisco IOS Release 12.1(8)EA1, entering the spanning-tree vlan vlan-id root global
configuration command on a Catalyst 3550 switch (no extended system ID) caused it to set its own
switch priority for the specified VLAN to 8192 if this value caused this switch to become the root for
the specified VLAN. If any root switch for the specified VLAN has a switch priority lower than 8192,
the switch sets its own priority for the specified VLAN to 1 less than the lowest switch priority.
These examples show the effect of the spanning-tree vlan vlan-id root command with and without the
extended system ID support:
• For Catalyst 3550 switches with the extended system ID (Cisco IOS Release 12.1(8)EA1 and later),
if all network devices in VLAN 20 have the default priority of 32768, entering the spanning-tree
vlan 20 root primary command on the switch sets the switch priority to 24576, which causes this
switch to become the root switch for VLAN 20.
• For Catalyst 3550 switches without the extended system ID (software earlier than
Cisco IOS Release 12.1(8)EA1), if all network devices in VLAN 100 have the default priority of
32768, entering the spanning-tree vlan 100 root primary command on the switch sets the switch
priority for VLAN 100 to 8192, which causes this switch to become the root switch for VLAN 100.

Note If your network consists of switches that both do and do not support the extended system ID, it is
unlikely that the switch with the extended system ID support will become the root switch. The extended
system ID increases the switch priority value every time the VLAN number is greater than the priority
of the connected switches running older software.

Note The root switch for each spanning-tree instance should be a backbone or distribution switch. Do not
configure an access switch as the spanning-tree primary root.

Use the diameter keyword to specify the Layer 2 network diameter (that is, the maximum number of
switch hops between any two end stations in the Layer 2 network). When you specify the network
diameter, the switch automatically sets an optimal hello time, forward-delay time, and maximum-age
time for a network of that diameter, which can significantly reduce the convergence time. You can use
the hello keyword to override the automatically calculated hello time.

Note After configuring the switch as the root switch, we recommend that you avoid manually configuring the
hello time, forward-delay time, and maximum-age time by using the spanning-tree vlan vlan-id
hello-time, spanning-tree vlan vlan-id forward-time, and the spanning-tree vlan vlan-id max-age
global configuration commands.

OL-8565-01 15-15


Beginning in privileged EXEC mode, follow these steps to configure a switch to become the root for the
specified VLAN. This procedure is optional.

Command Purpose
Step 2 spanning-tree vlan vlan-id root primary Configure a switch to become the root for the specified VLAN.
[diameter net-diameter [hello-time seconds]] For vlan-id, you can specify a single VLAN identified by VLAN
ID number, a range of VLANs separated by a hyphen, or a series
of VLANs separated by a comma. The range is 1 to 4094.
• (Optional) For diameter net-diameter, specify the maximum
number of switches between any two end stations. The range
is 2 to 7.
• (Optional) For hello-time seconds, specify the interval in
seconds between the generation of configuration messages by
the root switch. The range is 1 to 10 seconds; the default is 2
seconds.
Note When you enter this command without the optional
keywords, the switch recalculates the forward-time,
hello-time, max-age, and priority settings. If you had
previously configured these parameters, the switch
recalculates them.
Step 4 show spanning-tree detail Verify your entries.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id root global
configuration command.

Configuring a Secondary Root Switch
When you configure a Catalyst 3550 switch that supports the extended system ID as the secondary root,
the switch priority is modified from the default value (32768) to 28672. The switch is then likely to
become the root switch for the specified VLAN if the primary root switch fails. This is assuming that
the other network switches use the default switch priority of 32768 and therefore are unlikely to become
the root switch. For Catalyst 3550 switches without the extended system ID support (software earlier
than Cisco IOS Release 12.1(8)EA1), the switch priority is changed to 16384.
You can execute this command on more than one switch to configure multiple backup root switches. Use
the same network diameter and hello-time values as you used when you configured the primary root
switch with the spanning-tree vlan vlan-id root primary global configuration command.

15-16 OL-8565-01


Beginning in privileged EXEC mode, follow these steps to configure a switch to become the secondary
root for the specified VLAN. This procedure is optional.

Command Purpose
Step 2 spanning-tree vlan vlan-id root secondary Configure a switch to become the secondary root for the specified
[diameter net-diameter [hello-time VLAN.
seconds]] • For vlan-id, you can specify a single VLAN identified by VLAN
ID number, a range of VLANs separated by a hyphen, or a series
of VLANs separated by a comma. The range is 1 to 4094.
• (Optional) For diameter net-diameter, specify the maximum
number of switches between any two end stations. The range is
2 to 7.
• (Optional) For hello-time seconds, specify the interval in
seconds between the generation of configuration messages by
the root switch. The range is 1 to 10 seconds; the default is 2
seconds.
Use the same network diameter and hello-time values that you used
when configuring the primary root switch. See the “Configuring the
Root Switch” section on page 15-14.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id root global

Configuring the Port Priority
If a loop occurs, spanning tree uses the port priority when selecting an interface to put into the
forwarding state. You can assign higher priority values (lower numerical values) to interfaces that you
want selected first and lower priority values (higher numerical values) that you want selected last. If all
interfaces have the same priority value, spanning tree puts the interface with the lowest interface number
in the forwarding state and blocks the other interfaces.
Beginning in privileged EXEC mode, follow these steps to configure the port priority of an interface.
This procedure is optional.

Command Purpose
Step 2 interface interface-id Specify an interface to configure, and enter interface
configuration mode.
Valid interfaces include physical interfaces and
port-channel logical interfaces (port-channel
port-channel-number).

OL-8565-01 15-17


Command Purpose
Step 3 spanning-tree port-priority priority Configure the port priority for an interface.
For priority, the range is 0 to 240 in increments of 16. The
default is 128. The lower the number, the higher the
priority.
Valid priority values are 0, 16, 32, 48, 64, 80, 96, 112, 128,
144, 160, 176, 192, 208, 224, and 240. All other values are
rejected.
Step 4 spanning-tree vlan vlan-id port-priority priority Configure the VLAN port priority for an interface.
• For vlan-id, you can specify a single VLAN identified
by VLAN ID number, a range of VLANs separated by
a hyphen, or a series of VLANs separated by a comma.
The range is 1 to 4094.
For priority, the range is 0 to 240 in increments of 16.
The default is 128. The lower the number, the higher
the priority.
Valid priority values are 0, 16, 32, 48, 64, 80, 96, 112,
128, 144, 160, 176, 192, 208, 224, and 240. All other
values are rejected.
Step 6 show spanning-tree interface interface-id Verify your entries.
or
show spanning-tree vlan vlan-id

Note The show spanning-tree interface interface-id privileged EXEC command displays information only
if the port is in a link-up operative state. Otherwise, you can use the show running-config interface
privileged EXEC command to confirm the configuration.

To return the interface to its default setting, use the no spanning-tree [vlan vlan-id] port-priority
interface configuration command. For information on how to configure load sharing on trunk ports by
using spanning-tree port priorities, see the “Load Sharing Using STP” section on page 11-23.

Configuring the Path Cost
The spanning-tree path cost default value is derived from the media speed of an interface. If a loop
occurs, spanning tree uses cost when selecting an interface to put in the forwarding state. You can assign
lower cost values to interfaces that you want selected first and higher cost values that you want selected
last. If all interfaces have the same cost value, spanning tree puts the interface with the lowest interface
number in the forwarding state and blocks the other interfaces.

15-18 OL-8565-01


Beginning in privileged EXEC mode, follow these steps to configure the cost of an interface. This
procedure is optional.

Command Purpose
Step 2 interface interface-id Specify an interface to configure, and enter interface
configuration mode. Valid interfaces include physical interfaces
and port-channel logical interfaces (port-channel
port-channel-number).
Step 3 spanning-tree cost cost Configure the cost for an interface.
If a loop occurs, spanning tree uses the path cost when selecting
an interface to place into the forwarding state. A lower path cost
represents higher-speed transmission.
For cost, the range is 1 to 200000000; the default value is derived
from the media speed of the interface.
Step 4 spanning-tree vlan vlan-id cost cost Configure the cost for a VLAN.
If a loop occurs, spanning tree uses the path cost when selecting
an interface to place into the forwarding state. A lower path cost
represents higher-speed transmission.
• For vlan-id, you can specify a single VLAN identified by
VLAN ID number, a range of VLANs separated by a hyphen,
or a series of VLANs separated by a comma. The range is 1
to 4094.
• For cost, the range is 1 to 200000000; the default value is
derived from the media speed of the interface.
Step 6 show spanning-tree interface interface-id Verify your entries.
or
show spanning-tree vlan vlan-id

Note The show spanning-tree interface interface-id privileged EXEC command displays information only
for ports that are in a link-up operative state. Otherwise, you can use the show running-config privileged
EXEC command to confirm the configuration.

To return the interface to its default setting, use the no spanning-tree [vlan vlan-id] cost interface
configuration command. For information on how to configure load sharing on trunk ports by using
spanning-tree path costs, see the “Load Sharing Using STP” section on page 11-23.

OL-8565-01 15-19


Configuring the Switch Priority of a VLAN
You can configure the switch priority and make it more likely that the switch will be chosen as the root
switch.

Note Exercise care when using this command. For most situations, we recommend that you use the
spanning-tree vlan vlan-id root primary and the spanning-tree vlan vlan-id root secondary global
configuration commands to modify the switch priority.

Beginning in privileged EXEC mode, follow these steps to configure the switch priority of a VLAN. This

Command Purpose
Step 2 spanning-tree vlan vlan-id priority priority Configure the switch priority of a VLAN.
VLAN ID number, a range of VLANs separated by a
hyphen, or a series of VLANs separated by a comma. The
range is 1 to 4094.
• For priority, the range is 0 to 61440 in increments of
4096; the default is 32768. The lower the number, the
more likely the switch will be chosen as the root switch.
Valid priority values are 4096, 8192, 12288, 16384,
20480, 24576, 28672, 32768, 36864, 40960, 45056,
49152, 53248, 57344, and 61440. All other values are
rejected.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id priority global

Configuring Spanning-Tree Timers
Table 15-4 describes the timers that affect the entire spanning-tree performance.

Table 15-4 Spanning-Tree Timers

Variable Description
Hello timer Determines how often the switch broadcasts hello messages to other switches.
Forward-delay timer Determines how long each of the listening and learning states last before the interface begins
forwarding.

15-20 OL-8565-01


Table 15-4 Spanning-Tree Timers (continued)

Variable Description
Maximum-age timer Determines the amount of time the switch stores protocol information received on an interface.
Transmit hold count Controls the number of BPDUs sent every second.

The sections that follow provide the configuration steps.

Configuring the Hello Time
You can configure the interval between the generation of configuration messages by the root switch by
changing the hello time.

Note Exercise care when using this command. For most situations, we recommend that you use the
spanning-tree vlan vlan-id root primary and the spanning-tree vlan vlan-id root secondary global
configuration commands to modify the hello time.

Beginning in privileged EXEC mode, follow these steps to configure the hello time of a VLAN. This

Command Purpose
Step 2 spanning-tree vlan vlan-id hello-time seconds Configure the hello time of a VLAN. The hello time is the
interval between the generation of configuration messages by
the root switch. These messages mean that the switch is alive.
range is 1 to 4094.
• For seconds, the range is 1 to 10; the default is 2.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id hello-time global

OL-8565-01 15-21


Configuring the Forwarding-Delay Time for a VLAN
Beginning in privileged EXEC mode, follow these steps to configure the forwarding-delay time for a
VLAN. This procedure is optional.

Command Purpose
Step 2 spanning-tree vlan vlan-id forward-time Configure the forward time of a VLAN. The forward delay is the
seconds number of seconds a port waits before changing from its
spanning-tree learning and listening states to the forwarding state.
VLAN ID number, a range of VLANs separated by a hyphen,
or a series of VLANs separated by a comma. The range is 1 to
4094.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id forward-time global

Configuring the Maximum-Aging Time for a VLAN
Beginning in privileged EXEC mode, follow these steps to configure the maximum-aging time for a
VLAN. This procedure is optional.

Command Purpose
Step 2 spanning-tree vlan vlan-id max-age seconds Configure the maximum-aging time of a VLAN. The
maximum-aging time is the number of seconds a switch waits
without receiving spanning-tree configuration messages before
attempting a reconfiguration.
range is 1 to 4094.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id max-age global

15-22 OL-8565-01


Configuring Spanning Tree for Use in a Cascaded Stack
Spanning tree uses default values that can be reduced when configuring your switch in cascaded
configurations. If a root switch is part of a cluster that is one switch from a cascaded stack, you can
customize spanning tree to reconverge more quickly after a switch failure. Figure 15-4 shows switches
in three cascaded stacks that use the GigaStack GBIC. Table 15-5 shows the default spanning-tree
settings and those that are acceptable for these configurations.

Table 15-5 Default and Acceptable Spanning-Tree Parameter Settings (in seconds)

STP Parameter STP Default Acceptable for Option 1 Acceptable for Option 2 Acceptable for Option 3
Hello Time 2 1 1 1
Max Age 20 6 10 6
Forwarding Delay 15 4 7 4

Figure 15-4 Gigabit Ethernet Stack

Catalyst 2950, Cisco 7000
Catalyst 3550 2955, or 3550 router
series switch switches

Catalyst 2950, 2955, Catalyst Catalyst Layer 3
or 3550 switches 2950, 2955, 3550 or backbone
or 3550 6000 series
switches backbone

Catalyst 6000 Cisco 7000
switch router

74621

Option 1: Option 2: Option 3:
standalone cascaded cascaded
cascaded cluster connected to cluster connected to
cluster a Layer 2 backbone a Layer 3 backbone

Configuring the Transmit Hold Count
You can configure the maximum number of BPDUs that can be sent in one second by changing the
transmit hold-count value.

Note Increasing the transmit hold-count value can have a significant impact on CPU utilization in
rapid-PVST+ mode. Decreasing this value might slow down convergence. We recommend that you
maintain the default setting.

Beginning in privileged EXEC mode, follow these steps to configure the transmit hold count. This

OL-8565-01 15-23

Displaying the Spanning-Tree Status

Command Purpose
Step 2 spanning-tree transmit hold-count value Configure the number of BPDUs sent every second.
For value, the range is 1 to 20; the default is 6.

To return to the default setting, use the no spanning-tree transmit hold-count value global

Displaying the Spanning-Tree Status
To display the spanning-tree status, use one or more of the privileged EXEC commands in Table 15-6:

Table 15-6 Commands for Displaying Spanning-Tree Status

Command Purpose
show spanning-tree active Displays spanning-tree information on active interfaces only.
show spanning-tree detail Displays a detailed summary of interface information.
show spanning-tree interface interface-id Displays spanning-tree information for the specified interface.
show spanning-tree summary [totals] Displays a summary of port states or displays the total lines of the STP state
section.

You can clear spanning-tree counters by using the clear spanning-tree [interface interface-id]
privileged EXEC command.
For information about other keywords for the show spanning-tree privileged EXEC command, see the
command reference for this release.

15-24 OL-8565-01

Configuracion

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Configuracion (20)

More from 1 2d (20)

Recently uploaded (20)

Configuracion