Data Acquisition Equipment for Automation and Process Control

General
Specifications
<<Contents>> <<Index>>
GS 04L42B01-01E
GS 04L42B01-01E
©Copyright November. 2005
1st Edition Nov. 2005(KP)
14th Edition Sep. 2014(KP)
OVERVIEW
The DX2000 is a DAQSTATION that displays real-time
measured data on a color LCD and saves data on a
CompactFlash memory card (CF card). It can be hooked
up to network via Ethernet, which enables to inform by E-
mail and to monitor on Web site as well as to transfer
files by using FTP. Also, it can communicate with
Modbus/RTU or Modbus/TCP.
It comes with a four, eight, ten, twenty, thirty, forty-
channel or forty eight-channel model. As the input signal,
a DC voltage, thermocouple, resistance temperature
detector, or contact signal can be set to each channel.
The data saved on a CF card can be converted by data
conversion software to Lotus 1-2-3, Excel, or ASCII
format file, facilitating processing on a PC. Not only this,
the Viewer software allows a PC to display waveforms on
its screen and to print out waveforms.
STANDARD SPECIFICATIONS
General Specifications
Construction
Mounting: Flush panel mounting (on a vertical plane)
Mounting may be inclined downward up to
30 degrees from a horizontal plane.
Allowable panel thickness:
2 to 26 mm
Material: Case: drawn steel
Bezel: polycarbonate
Display filter: polycarbonate
Case color:
Case: Grayish blue green
(Munsell 2.0B 5.0/1.7 or equivalent)
Bezel: Charcoal grey light
(Munsell 10B 3.6/0.3 or equivalent)
Front panel:
Water and dust-proof*
(based on IEC529-IP65 and NEMA No.250
TYPE4 for indoor locations (except external
icing test))
*Except for side-by-side mounting.
Dimensions:
288 (W) ϫ288 (H) ϫ221.6 (D) mm
288 (W) ϫ288 (H) ϫ226 (D) *mm
*In case of /H2 or /PM1 option is specified.
Weight: DX2004, DX2010: approx. 6.0 kg*
DX2008, DX2020: approx. 6.3 kg*
DX2030 : approx. 6.9 kg*
DX2040, DX2048: approx. 7.3 kg*
*without optional features
Input
Number of inputs:
DX2004: four channels
DX2008: eight channels
DX2010: ten channels
DX2020: twenty channels
DX2030: thirty channels
DX2040: forty channels
DX2048: forty eight channels
Measurement interval:
DX2004, DX2008:
125 ms, 250 ms, 25 ms (fast sampling
mode*)
DX2010, DX2020, DX2030, DX2040, DX2048:
1 s (Not available when A/D integration
time is set to 100 ms), 2 s, 5 s, 125 ms
(fast sampling mode*)
* A/D integration time is fixed to 1.67 ms in case of
fast sampling mode.
Inputs: DCV (DC voltage), TC (thermocouple), RTD
(resistance temperature detector), DI (digital
input for event recording), DCA (DC current
with external shunt resistor attached)
Daqstation
DX2000

2
All Rights Reserved. Copyright © 2005, Yokogawa Electric Corporation
GS 04L42B01-01E 14th Edition Sep. 12, 2014-00
Input type Range
0.0 to 1760.0°C
0.0 to 1760.0°C
0.0 to 1820.0°C
–200.0 to 1370.0°C
–200.0 to 800.0°C
–200.0 to 1100.0°C
–200.0 to 400.0°C
–270.0 to 1300.0°C
0.0 to 2315.0°C
–200.0 to 900.0°C
–200.0 to 400.0°C
0.0 to 2400.0°C
–200.0 to 600.0°C
–200.0 to 550.0°C
OFF : less than 2.4 V
ON : more than 2.4 V
Contact ON/OFF
DCV
TC
RTD
DI
*1 R, S, B, K, E, J, T, N: IEC584-1 (1995), DIN IEC584,JIS C 1602-1995
*2 W: W-5% Re/W-26% Re (Hoskins Mfg. Co.), ASTM E988-96
(Type C equivalent of OMEGA Engineering Inc.)
*3 L: Fe-CuNi, DIN43710, U: Cu-CuNi, DIN43710
*4 WRe: W-3%Re/W-25%Re (Hoskins Mfg. Co.), ASTM E988-96
(Type D equivalent of OMEGA Engineering Inc.)
*5 Pt100: JIS C 1604-1997, IEC 751-1995, DIN IEC751-1996
JPt100: JIS C 1604-1989,JIS C 1606-1989
Measuring current: i = 1mA
32 to 3200°F
32 to 3200°F
32 to 3308°F
–328 to 2498°F
–328.0 to 1472.0°F
–328.0 to 2012.0°F
–328.0 to 752.0°F
–454 to 2372°F
32 to 4199°F
–328.0 to 1652.0°F
–328.0 to 752.0°F
32 to 4352°F
–328.0 to 1112.0°F
–328.0 to 1022.0°F
Measuring range
–20.000 to 20.000 mV
–60.00 to 60.00 mV
–200.00 to 200.00 mV
–2.0000 to 2.0000 V
–6.000 to 6.000 V
–0.800 to 5.200 V
–20.000 to 20.000 V
–50.00 to 50.00 V
20 mV
60 mV
200 mV
2 V
6 V
1-5V
20 V
50 V
R*1
S*1
B*1
K*1
E*1
J*1
T*1
N*1
W*2
L*3
U*3
WRe*4
Pt100*5
JPt100*5
DCV input
(TTL)
Contact input
A/D integration time:
20 ms (50 Hz), 16.7 ms (60 Hz), 100ms (50/
60Hz for DX2010/2020/2030/2040/2048), or
AUTO selectable (automatic selection by
detection of power supply frequency)
A/D integration time is fixed to 1.67 ms
(600Hz) in case of fast sampling mode.
Thermocouple burnout:
Burnout upscale/downscale function can be
switched on/off (for each channel).
Burnout upscale/downscale selectable
Normal: Less than 2 k⍀, Burn out: More
than 100 k⍀
Detection current: approx. 10 ␮ A
1-5V range burnout:
Burnout upscale/downscale function can be
switched on/off (for each channel).
Burnout upscale/downscale selectable
Upscale burnout: More than +10% of
configured span
Downscale burnout: Less than -5% of
configured span
Moving average:
Moving average on/off selectable for each
channel
Moving average cycles 2 to 400 selectable
Calculation:
Differential computation:
Between any two channels
Available for DCV, TC, RTD and DI
ranges.
Linear scaling:
Available for DCV, TC, RTD and DI
ranges.
Scaling limits: -30000 to 30000
Decimal point: user-selectable
Engineering unit: user-definable, up to 6
characters
Over value: Exceeds ؎ 5% of scaling
limits (on/off selectable)
Square root:
Available for DCV range.
Engineering unit : user-definable, up to 6
characters
Low level cut off: 0.0 to 5.0% of display
span
1-5VDC scaling:
Available for 1-5VDC range.
Display span limit: 0.800 to 5.200
Engineering unit : user-definable, up to 6
characters
Low level cut off: Fixed to lower span limit
Display
Display unit:
10.4-inch TFT color LCD (VGA, 640 x 480
pixels)
Note) In the part of crystal display, there are some pixels
that can't always turn on or off. Please understand
that the brightness of screen looks uneven because
of characteristics of crystal display, but it is not out
of order.
Display group:
Each measurement channel and computation channel
can be assigned to display group of the trend, digital
and bargraph display.
Number of display: 36 groups
Number of assignable channels for one
group: 10 channels
Display color:
Trend/Bargraph:
Selectable from 24 colors
Background:
White or black selectable
Trend display:
Trend display type:
Vertical, horizontal, landscape, horizontal
split or circular selectable
Number of indication channels:
10 channels per display (maximum)
Number of display:
36 displays (36 groups)
Line width:
1, 2, and 3 pixels selectable
Scales: Maximum 10 scales.
Bargraph, green band area and alarm
mark can be displayed on scale display.
Number of divisions: Selectable from 4 to
12 or C10 (10 divisions by main scale
mark and scale values are displayed on 0,
30, 50, 70 and 100% position).

3<<Contents>> <<Index>>
All Rights Reserved. Copyright © 2005, Yokogawa Electric Corporation GS 04L42B01-01E 14th Edition Sep. 12, 2014-00
Trend update rate:
5, 10, 15, 30 sec.,1, 2, 5, 10, 15, 20, 30
min., 1, 2, 4, 10 hours/div selectable
(5, 10 sec/div is available for only DX2004
and DX2008. DX2010, DX2020, DX2030,
DX2040, and ,DX2048 can be specified to
15 sec/div when they are in fast sampling
mode.)
Circular waveform span rate:
20, 30 min., 1, 2, 6, 8, 12, 16 hours, 1, 2
days, 1, 2, 4 weeks/rev selectable
(20 min/rev is available for only DX2004
and DX2008)
Bargraph display:
Direction: Vertical or horizontal selectable
10 channels per display
Number of display:
Scales: Green band area and alarm mark can be
displayed on scale display.
Number of divisions: Selectable from 4 to 12
Reference position: Left, right or center
Display renewal rate: 1 s
Digital indication:
10 channels per display
Number of display:
Display renewal rate: 1 s
Overview display:
Measuring values and alarm status of all
channels
Information display:
Alarm summary display:
Display the list of latest 1000 alarms
summary.
Jump to historical trend display by cursor
pointing.
Message summary display:
Display the list of latest 450 messages
and time.
pointing.
Memory information:
Display the file list in internal memory.
pointing.
Report information:
Display the report data in internal memory.
Modbus status:
Display the Modbus status.
Relay status:
Display the on/off status of internal switch
and relay output.
Stacked bar graph display:
Display the periodic sums of report data.
Event switch status:
Display the event switch status.
Log display:
Log display types:
Login log*1
, error log, communication log,
FTP log, Web log, E-mail log, SNTP log,
DHCP log, Modbus log, operation log*2
,
setting change log*2
*1 operation log when the /AS1 option is
installed
*2 only for /AS1 option
Tags:
Display the tag number and tag comment.
Tag number:
Number of characters:
16 characters maximum
Tag comment:
Messages:
Number of messages:
100 messages (including 10 free mes-
sages)
Message adding function:
Message can be added on historical
display.
Other display contents:
Status display area:
Date & time (year/month/day,
hour:minute:second), batch name (batch
number + lot number), login user name,
display name, internal memory status,
status indication icon
Trend display area:
Grid lines (number of divisions selectable
from 4 to 12), hour : minutes on grid, trip
levels (line widths are selectable from 1, 2
and 3 pixels)
Data referencing function:
Display the retrieved data (display data or event data)
from internal or external memory.
Display format:
Whole display or divided to 2 areas
Time axis operation:
Display magnification or reduction, scroll
by key operation
Data searching operation:
Display the retrieved data from internal
memory by specifying date and time.
Display auto scroll function:
Display group of monitor display (trend
display, bargraph display and digital display)
automatically changes in a preset interval
(5, 10, 20, 30 s and 1 min).
Sign record:
Only for /AS1 option
LCD saver function:
The LCD backlight automatically dims or off
(selectable) if no key is touched for a certain
preset time (can be set from 1, 2, 5, 10, 30,
and 60 min).
Display register function:
Up to 8 display types can be registered with
display name.
Display auto return function:
The display type automatically returns to
registerd display type if no key is touched
for a certain preset time (can be set from 1,
2, 5, 10, 20, 30 and 60 min)
Temperature unit:
°C or °F selectable
Custom display function:
Display can be customized by lay outing display parts.
Display data is saved in internal memory or external
medium.
Number of customized display:
28 displays maximum (3 in internal
memory and 25 in external medium)

4
Display part:
- General parts (digital, bar, label, tag
number, tag comment, system icon,
Modbus input, etc)
- Scale parts
- Trend parts
- List parts (alarm list, message list)
- Figure parts (line, rectangle, circle)
Edit function:
Select parts, grid, edit parts (move, resize,
property, copy, paste, layout order change,
dependency of visual property), group
control, delete, save display
Custom display data:
Contents: Display contents data (for
each display)
Format: Text
Output: External medium
Custom display data save/load:
Each or all custom display data file can be
saved in specified directory.
Custom display data can be loaded from
specified directory.
Data Saving Function
External storage medium:
Medium: CompactFlash memory card (CF card)
Format: FAT16 or FAT32
Internal memory:
Medium: Flash memory
Capacity: 400MB
Maximum number of files can be saved:
400 files (total number of display data file
and event data file)
Manual saving:
Data files in internal memory can be saved manually.
Selectable form all data saving or selected data
saving.
Drive: CF card or USB flash drive (only for USB option)
Automatic saving:
Display data:
Periodic saving to CF card
Event data:
In case of trigger free...Periodic saving to
CF card
In case of using trigger...Save the data
when sampling is finished
Media FIFO function :
Allows the oldest file to be deleted and the
newest file to be saved if the free space on
the CF card is insufficient (on/off selectable).
Sampling Period (data saving period):
Display data file:
Linked with the trend update rate
Event file: Linked with the specified sampling period
Event File Sampling Period:
DX2004, DX2008:
Selectable from 25, 125, 250, 500 ms, and
1, 2, 5, 10, 30, 60, 120, 300, 600, 900,
1200 and 1800 s*
DX2010, DX2020, DX2030, DX2040, DX2048:
Selectable from 125, 250, 500 ms, and 1,
2, 5, 10, 30, 60, 120, 300, 600, 900, 1200
and 1800 s*
*Sampling period faster than measurement interval
can not be selected.
Measurement data File:
The following two file types can be created.
Event file (stores instantaneous values
sampled periodically at a specified
sampling period)
Display data file (stores the maximum and
minimum values for each sampling period
from among measured data sampled at
measurement intervals)
Files can be created in the following combinations.
(a) Event file + display data file
(b) Display data file only
(c) Event file only
Data format: YOKOGAWA private format (Binary)
Maximum data size per file:
8,000,000 byte (8MB)
Data per channel:
Display data file:
Measurement data......4 byte/data
Mathematical data......8 byte/data
External channel data..4 byte/data
Event data file:
Measurement data......2 byte/data
Mathematical data......4 byte/data
External channel data..2 byte/data
Sampling time:
The sampling time per file (8MB) during manual data
saving can be determined by the formula "number of
data items per channel x interval of data saving
(sampling period)."
This logic is explained in more detail below:
1) When handling display data files only
If we assume that the number of measuring
channels is 30, the number of computing channels
is 10, and the trend update rate is 30 min/div (60
sec sampling period), then:
Number of data items per channel = 8,000,000
bytes/(8 bytes(time stamp) + 30 x 4 bytes + 10 x
8 bytes) = 38,462 data items
Sampling time per file = 38,462 x 60 sec =
2,307,720 sec = approx. 26 days
2) When handling event files only
If we assume that the number of measuring
channels is 30, the number of computing channels
is 10, and the sampling period is 1 sec, then :
Number of data items per channel = 8,000,000
bytes/(8 bytes(time stamp) + 30 x 2 bytes + 10 x
4 bytes) = 74,074 data items
Sampling time per file = 74,074 x 1 sec =
74,074 sec = approx. 20 hours
3)When handling both display data files and event
files
The sampling time is calculated by defining the size
of data items in a display data file as 8,000,000
bytes and the size of data items in an event data file
as 8,000,000 bytes. The method of calculation is
the same as shown above.
Examples of Sampling Time for 1 file (8MB)*:
*If sampling time exceeds 31 days, data file is divided.

In case measurement ch = 8 ch, mathematical ch = 0 ch
Display data file (approx.)
Trend update rate
(time/div)
Sampling period
Sampling time
30 s
1 s
2 days
1 min
2 s
4 days
2 min
4 s
9 days
5 min
10 s
23 days
10 min
20 s
46 days
Event data file (approx.)
Sampling period
Sampling time
2 s
7 days
0.5 s
46.3 h
1 s
3 days
125 ms
11.6 h
5 s
19 days
10 s
38 days
15 s
0.5 s
27.8 h
25 ms
2.3 h
In case measurement ch = 48 ch, mathematical ch = 60 ch
Display data file (approx.)
Trend update rate
(time/div)
Sampling period
Sampling time
1 min
2 s
6.5 h
5 min
10 s
32.7 h
20 min
40 s
5 days
30 min
1 min
8 days
1 h
2 min
16 days
Event data file (approx.)
Sampling period
Sampling time
10 s
2 days
0.5 s
3.2 h
125 ms
48 min
15 s
0.5 s
1.6 h
25 ms
NA
30 s
8 days
1 min
16 days
10 min
20 s
2 days
2 h
4 min
32 days
1 s
6.5 h
2 min
32 days
Manual sample data:
The measuring and computing data can be saved
manually to the internal memory and CF card.
Trigger: Key operation, communication command
or event action function
Data format:
Text
Max. number of data:
400 data (if exceeds 400 data, oldest data
is overwritten)
Report data (only for MATH option):
Types: Hourly, daily, hourly + daily, daily + weekly,
and daily + monthly
Data format:
Text
Drive: CF card
Trigger function:
Selectable from FREE or TRIG for event data saving.
Trigger mode:
Selectable from free, single or repeat
trigger
Data length:
Selectable from 10, 20, 30 min, 1, 2, 3, 4,
6, 8, 12 hour, 1, 2, 3, 5, 7, 10, 14, 31 day
Pre trigger: Selectable from 0, 5, 25, 50, 75, 95, 100%
Trigger source:
Key operation, communication command
Display hard copy:
Trigger: Key operation, communication command
Data format:
png format
Drive/output:
CF card or communication interface
Data file retrieving function:
Data file in CF card or USB flash drive (only for USB
option) can be retrieved and displayed.
Retrieved data file:
Display data file or event data file
Saving and retrieving of configuration data:
Configuration information can be saved and retrieved
as text data.
Drive: CF card or USB flash drive (only for USB
option)
Alarm Function
Number of alarm levels:
Up to four levels for each channel
Alarm types:
High and low limits, differential high and low
limits, high and low rate-of-change limits and
delay high and low
Alarm delay time:
1 to 3600 s*
* with the /AS1 option, it can be setup to 24 hours
Interval time of rate-of-change alarms:
The measurement interval times 1 to 32
Display: The alarm status (type) is displayed in the
digital value display area upon occurrence of
an alarm. A common alarm indication is also
displayed.
Alarm display color and display order can be
changed by configured importance level and
color.
Alarming behavior:
non-hold or hold-type can be selectable for
common to all channels.
Hysteresis: On/off selectable (common to measurement
channels, mathematical channels or external
channels)
0.0 to 5.0% of display span (or scaling span)
Outputs:
Output: Internal switch or relay output (optional)
Number of internal switch:
30 points
Internal switch action:
AND/OR
Number of relay output points:
2, 4, 6, 12, 22 or 24 points (optional)
Relay action:
Energized/deenergized, hold/non-hold,
AND/OR, alarm reflash selectable.
Alarm no logging function:
When alarm occurs, only internal switch or
relay output is activated. There are no
alarm display on screen and no record on
alarm summary.
On/off selectable for each channel and
alarm level.

6
Memory:
The times of alarm occurrences/recoveries, alarm
types, etc. are stored in the memory.
Up to 1000 latest alarm events are stored.
Alarm annunciator function:
Alarm display and relay output based on alarm
sequence.
Alarm sequence: 3 types (ISA-A-4, ISA-A, ISA-M)
First out display function: Not available
Event action function
General: Particular action can be executed by
particular event.
Number of event action:
40 actions can be set
Event list:
Level/Edge DescriptionEvent
Remote
Relay
Internal switch
Alarm
Timer
Match time
USER key
Level/Edge
Level/Edge
Level/Edge
Level/Edge
Edge
Edge
Edge
Action by remote control signal
Action by relay operation
Action by internal switch operation
Action by any alarm
Action by timer time up
Action by time up of match time timer
Action by USER key operation
Relay OFF
Level switch OFF
Level/Edge
Level/Edge
Action by Relay OFF
Action by level switch OFF
Event level switch Level/Edge Action by custom display, or
communication command
Alarm OFF Level/Edge Action by alarm OFF
Internal switch
OFF
Level/Edge Action by internal switch OFF
Event edge
switch
Edge Action by custom display, FUNC
display or communication command
Action list:
Level/Edge DescriptionAction
Memory
start/stop
Memory start
Memory stop
Event trigger*
Alarm ACK
Math start/stop
Math stop
Math reset
Level
Edge
Edge
Edge
Edge
Level
Edge
Memory start and stop
Memory start
Memory stop
Event data sampling start
Alarm ACK
Computation start and stop
Computation start
Edge Computation stop
Manual sample
Edge Computation reset
Snapshot
Edge Manual sample
Message input
Edge Save display image to external media
Trend update rate
change
Edge Message writing
Display data save
Level Change trend update rate
Event data save
Edge Save currently sampled display data
to internal memory as a file
Relative time
timer reset
Edge Save currently sampled event data to
internal memory as a file
Display group
change
Edge Reset relative time timer
Time adjustment
Edge Change to specified display group
Flag
Edge Adjust internal clock to the nearest
hour
Setting file load* Edge
Load setting file from CF card
(up to 3 setting files).
Math start
Level Normal: "0", Event: "1"
Alarm display reset Edge Reset alarm display
Comment display Edge Display comment
Favorite display
* Not available with /AS1 option.
Edge Display registered favorite screen
Security functions*
General: Login function or key lock function can be
set for each key operation or communication
operation.
Key lock function:
On/off and password can be set for each
operation key and FUNC operation. (Not
available with /AS1 option)
Login function:
Using the login function described below, you can
enter security settings on the instrument
- User name
- Password
User level and number of users:
System administrator: 5 users (all can be
operated)
General user: 30 users (With user
restrictions, you
can set restrictions
on each operation
key and FUNC
display operation.)
User restrictions setting: 10 kinds (for
general users)
* If the /AS1 option is installed, see the advanced
security function (/AS1) specifications on page 15
Clock
Clock: With calendar function (year of grace)
Clock accuracy:
؎ 10 ppm, excluding a delay (of 1 second,
maximum) caused each time the power is
turned on.
Time setting method:
Key operation, communication command,
event action function or SNTP client function
Time adjustment method:
During memory sample:
Adjust 40 ms per second (No influence for
measurement period)
During memory stop:
Adjust at a time
Time zone:
Time difference from GMT:
Settable from -1300 to 1300
Date display format:
Selectable from YYYY/MM/DD, MM/DD/
YYYY, DD/MM/YYYY or DD.MM.YYYY
DST function (summer/winter time):
The time at which the daylight savings time
adjustment is automatically calculated and
configured.
Communication Functions
Electrical specifications:
Confirms to IEEE802.3 (DIX specification for
Ethernet frames)
Connection:
Ethernet (10BASE-T)
Protocols: TCP, UDP, IP, ICMP, ARP, DHCP, HTTP,
FTP, SMTP, SNTP, Modbus, DX private,
EtherNet/IP
E-mail inform function:
E-mail is sent by events as below.
- Alarm occurring/alarm canceling
- Recover from power failure
- Memory end
- Storage medium error, FTP client function
error
- Specified time period

- Report data time up (only for mathematical
option)
- When a user locked (only for /AS1 option)
POP before SMTP and SMTP authentication (PLAIN
and CRAM-MD5) is available.
FTP client function:
Data file auto-transfer from DX
Transferred data file:
Display data file, event data file, report
data file and display image file, setting file
(only for /AS1 option)
FTP server function:
File transfer from DX, file elimination (Not
available with /AS1 option), directory
operation and file list output are available by
request from host computer.
Web server function:
Display image of DX and alarm information
can be displayed on web browser.
Display the data searching display and
report data of DX on web browser.
You can have a buzzer sound on the PC
when an alarm occurs on the DX.
SNTP client function:
The time on DX can be synchronized to the
time of a SNTP server.
SNTP server function:
The DX can operate as a SNTP server.
DHCP client function:
Network address configuration can be obtained
automatically from DHCP server.
Obtained information:
IP address, subnet mask, default gateway
and DNS information
Modbus client function:
Reading or writing of measurement data on
other instruments are available by Modbus
protocol.
Mathematical option or external input option
is required to read the data from other
instruments.
Modbus server function:
Output of measurement data from DX is
available by Modbus protocol.
Control operation such as message or batch
name writing is available.
Access control from Modbus client to
register is available by IP filtering function.
Setting/measurement server function:
Operation, setting or output of measurement
data are available by DX private protocol.
Maintenance/test server function:
Output connection information or network
information of the Ethernet communication.
Instrument information server function:
Output instrument information such as serial
number or model name of DX.
EtherNet/IP server function:
- Reading of measurement data or math-
ematical channel data
- Reading or writing of external channel data
- Reading or writing of communication input
channel
Batch function
General: Data display and data management with
batch name, text field function and batch
comment function are available.
Batch name:
Batch name can be used as file name of display data,
event data and report data.
Batch name format:
Batch number (max. 32 characters) + lot
number (max. 8 characters)
Use/not use selectable for lot number, on/
off selectable for auto increment function
Text field function:
Field number:
1 to 24
Field title:
Max. 20 characters
Field text:
Max. 30 characters
Batch comment function:
Batch comment is added to display data and event
data.
Batch comment information:
3 comments (max. 50 characters) are
available.
Power Supply
Rated power supply:
100 to 240 VAC (automatic switching)
Allowable power supply voltage range:
90 to 132 or 180 to 264 VAC
Rated power supply frequency:
50/60 Hz (automatic switching)
Power consumption:
Supply voltage
100 VAC
240 VAC
LCD off
28 VA
38 VA
Normal
42 VA
54 VA
Max.
74 VA
100 VA
Allowable interruption time:
Less than 1 cycle of power supply frequency
Other Specifications
Memory backup :
A built-in lithium battery backs up the setup
parameters (battery life : approximately 10
years at room temperature).
Insulation resistance:
Each terminal to ground terminal:
20 M⍀ or greater (at 500 VDC)
Dielectric strength:
Power supply to ground terminal:
2300 VAC (50/60 Hz), 1 min
Contact output terminal to ground terminal:
1600 VAC (50/60 Hz), 1 min
Measuring input terminal to ground terminal:
1500 VAC (50/60 Hz), 1 min
Between measuring input terminals:
1000 VAC (50/60 Hz), 1 min (except for b-
terminal of RTD input of DX2010, DX2020,
DX2030, DX2040 and DX2048)
Between remote control terminal to ground terminal:
1000 VDC, 1 min
Safety and EMC Standards
CSA: CSA22.2 No.61010-1, CSA C22.2
No.61010-2-030
Installation category II*1
, pollution degree 2*2
,
measurement category II*3
UL: UL61010-1, UL61010-2-030 (CSA NRTL/C)

8
CE:
EMC directive:
EN61326-1 compliant, Class A Table 2
(For use in industrial locations)
EN61000-3-2 compliant
EN61000-3-3 compliant
EN55011 compliant, Class A, Group 1
Low voltage directive:
EN61010-1, EN61010-2-030 compliant,
Installation category II*1
, pollution
degree 2*2
, measurement category II*3
EMC Regulatory Arrangement in Australia and
New Zealand: EN55011 compliant, Class A, Group 1
*1: Installation Category (Overvoltage Cat-
egory) II
Describes a number which defines a
transient overvoltage condition. It implies
the regulation for impulse withstand
voltage. "II" applies to electrical equipment
which is supplied from fixed installations
like distribution boards.
*2: Pollution Degree
Describes the degree to which a solid,
liquid, or gas which deteriorates dielectric
strength or surface resistivity is adhering.
"2" applies to normal indoor atmosphere.
Normally, only non-conductive pollution
occurs.
*3: Measurement Category II
Applies to measuring circuits connected to
low voltage installation, and electrical
instruments supplied with power from fixed
equipment such as electric switchboards.
Normal Operating Conditions
Power voltage:
90 to 132 or 180 to 250 VAC
Power supply frequency:
50 Hz ؎2%, 60 Hz ؎2%
Ambient temperature:
0 to 50 °C
Ambient humidity:
20% to 80% RH (at 5 to 40 °C)
Vibration: 10 to 60 Hz, 0.2 m/s2
or less
Shock: Not acceptable
Magnetic field:
400 AT/m or less (DC and 50/60 Hz)
Noise:
Normal mode (50/60 Hz):
DCV: The peak value including the signal
must be less than 1.2 times the measuring
range.
TC: The peak value including the signal
must be less than 1.2 times the measuring
thermal electromotive force.
RTD: 50 mV or less
Common mode noise voltage (50/60 Hz):
250 Vrms AC or less for all ranges
Maximum noise voltage between channels (50/60 Hz):
250 Vrms AC or less
Mounting position:
Can be inclined up to 30 deg backward.
Mounting at an angle away from the
perpendicular is not acceptable.
Warm-up time:
At least 30 min after power on
Installation location:
In-room
Altitude: Less than 2000 m
Standard Performance
Measuring and Recording Accuracy:
The following specifications apply to operation of the
recorder under standard operation conditions.
Temperature:
23 ؎ 2 °C
Humidity:
55% ؎ 10% RH
Power supply voltage:
90 to 132 or 180 to 250 VAC
50/60 Hz ؎ 1%
Warm-up time:
At least 30 min.
Other ambient conditions such as vibration should not
adversely affect recorder operation.

Input Range
Measurement accuracy (digital display)
16.7ms or more
1.67ms (fast sampling mode)
DCV
TC
(Excluding
RJC
accuracy)
RTD
Max. resolution of
digital display
1 µV
10 µV
10 µV
100 µV
1 mV
1 mV
1 mV
0.1°C
±(0.05% of rdg + 12 digits)
±(0.15% of rdg + 1°C)
However,
R, S:
±3.7°C at 0 to 100°C
±1.5°C at 100 to 300°C
B:
±2°C at 400 to 600°C
Accuracy at less than 400°C
is not guaranteed.
±(0.2% of rdg + 4°C)
However,
R, S:
±10°C at 0 to 100°C
±5°C at 100 to 300°C
B:
±7°C at 400 to 600°C
Accuracy at less than
400°C is not guaranteed.
±(0.15% of rdg + 0.7°C)
However,
±(0.15% of rdg + 1°C) at
-200 to -100°C
±(0.2% of rdg + 3.5°C)
However,
±(0.15% of rdg + 6°C) at
-200 to -100°C
±(0.15% of rdg + 0.5°C)
However,
±(0.15% of rdg + 0.7°C) at
-200 to -100°C
±(0.2% of rdg + 2.5°C)
However,
±(0.2% of rdg + 5°C) at
-200 to -100°C
±(0.15% of rdg + 0.7°C)
However,
±(0.35% of rdg + 0.7°C) at
-200 to 0°C
Accuracy at less than -200°C
is not guaranteed.
±(0.3% of rdg + 3.5°C)
However,
±(0.7% of rdg + 3.5°C) at
-200 to 0°C
Accuracy at less than -200°C
is not guaranteed.
±(0.15% of rdg + 1°C) ±(0.3% of rdg + 7°C)
±(0.2% of rdg + 2.5°C)
However,
±4°C at 0 to 200°C
±(0.3% of rdg + 10°C)
However,
±18°C at 0 to 200°C
20 mV
60 mV
200 mV
2 V
6 V
1-5 V
20 V
10 mV50 V
B
S
R
K
E
J
T
L
U
N
W
WRe
±(0.15% of rdg + 0.3°C) ±(0.3% of rdg + 1.5°C)
Pt100
JPt100
Measurement accuracy in case of scaling (digits):
= measurement accuracy (digits) x scaling
span (digits)/measurement span (digits) + 2
digits
Decimals are rounded off to the next highest
number.
Reference junction compensation:
INT (internal)/EXT (external) selectable
(common for all channels)
Reference junction compensation accuracy:
Types R, S, B, W, WRe: ؎ 1 °C
Types K, J, E, T, N, L, U: ؎ 0.5 °C
(Above 0 °C, input terminal temperature is
balanced)
Maximum allowable input voltage:
؎ 60 VDC (continuous) for all input ranges
Input resistance:
Approx. 10 M⍀ or more for DCV ranges of
200 mVDC or less and TC
Approx. 1 M⍀ for more than 2 VDC ranges
Input source resistance:
DCV, TC: 2 k⍀ or less
RTD: 10 ⍀ or less per wire (The
resistance of all three wires must be equal.)
Input bias current:
10 nA or less (approx. 100nA for TC range
with burnout function)
Maximum common mode noise voltage:
250 Vrms AC (50/60 Hz)
Maximum noise voltage between channels:
250 Vrms AC (50/60 Hz)
Interference between channels:
120 dB (when the input source resistance is
500 ⍀ and the inputs to other channels are
60 V)
Common mode rejection ratio:
A/D integration time 20 ms:
More than 120 dB (50 Hz ؎ 0.1%, 500 ⍀
imbalance between the minus terminal and
ground)
A/D integration time 16.7 ms:
More than 120 dB (60 Hz ؎ 0.1%, 500 ⍀
ground)
More than 80 dB (50/60 Hz ؎ 0.1%, 500 ⍀
ground)
Normal mode rejection ratio:
A/D integration time 20 ms:
More than 40 dB (50 Hz ؎ 0.1%)
More than 40 dB (60 Hz ؎ 0.1%)
50/60Hz is not rejected.

10
Effects of Operating Conditions
Ambient temperature: (Only for 16.7 ms A/D integration
time or more)
With temperature variation of 10 °C
DCV, TC: ؎ (0.1% of rdg + 0.05% of
range) or less
Excluding the error of reference junction
compensation
RTD: ؎ (0.1% of rdg + 2 digits) or
less
Power supply:
With variation within 90 to 132 V and 180 to 250 VAC
(50/60 Hz):
Within measurement accuracy
With variation of ؎ 2 Hz from rated power frequency
(at 100 VAC):
Within measurement accuracy
Magnetic field:
AC (50/60 Hz) and DC 400 A/m fields:
؎ (0.1% of rdg + 10 digits) or less
(1) DCV range (with variation of +1 k⍀)
200 mVDC range or less:
؎ 10 ␮ V or less
2 VDC range or greater:
؎ 0.15% of rdg or less
(2) TC range (with variation of +1 k⍀)
؎ 10 ␮ V
(3) RTD range (Pt100)
With variation of 10 ⍀ per wire (resistance of all three
wires must be equal):
؎ (0.1% of rdg + 1 digit) or less
With maximum difference of 40 m⍀ between wires:
approx. ؎ 0.1 °C
Effects of Vibration
Effects from a sinusoidal vibration along all three axis
at a frequency between 10 to 60 Hz and an accelera-
tion of 0.2 m/s2
: ؎ (0.1% of rdg + 1 digit) or less
Transport and Storage Conditions
The following specifies the environmental conditions
required during transportation from shipment to the start
of service and during storage as well as during transpor-
tation and storage if this instrument is temporarily taken
out of service.
No malfunction will occur under these conditions without
serious damage, which is absolutely impossible to
repair; however, calibration may be necessary to
recover normal operation performance.
Ambient temperature:
-25 °C to 60 °C
Humidity: 5% to 95% RH (No condensation is
allowed.)
Vibration: 10 to 60 Hz, 4.9 m/s2
maximum
Shock: 392 m/s2
maximum (while being packed)
SPECIFICATIONS OF OPTIONAL FUNC-
TIONS
Alarm Output Relays (/A1, /A2, /A3, /A4, /A5)
An alarm signal is output from the rear panel as a relay
contact signal.
Number or output:
Select from 2, 4, 6, 12 and 24 points
Relay contact rating:
250 VDC/0.1 A (for resistance load), 250
VAC (50/60 Hz)/3 A
Terminal configuration:
SPDT (NO-C-NC). Energized-at-alarm/
deenergized-at-alarm,
AND/OR, and hold/non-hold actions are
selectable.
Serial Communication Interface (/C2, /C3)
Connection:
EIA RS-232 (/C2) or RS-422A/485 (/C3)
Protocols: DX private protocol, Modbus(master/slave)
protocol, DX private bar code protocol (only
for /AS 1 option)
Synchronization method:
Start-stop asynchronous transmission
Connection method (RS-422A/485):
4-wire half-duplex multi-drop connection
(1 : N, N = 1 to 31)
Transmission speed:
1200, 2400, 4800, 9600, 19200 or 38400
bps
Data length:
7 or 8 bits
Stop bit: 1 bit
Parity: Odd, even, or none
Communication distance (RS-422A/485):
Up to 1.2 km
Communication mode:
ASCII for input/output for control and setting
ASCII or binary for output of measured data
Setting/measurement server function:
Operation, setting or output of measurement
data are available by DX private protocol.
Modbus communication:
Reading or writing of measurement data on
other instruments are available by Modbus
protocol.
Mathematical function option or external
input option is needed to read measurement
data from other instruments.
Control operation such as message or batch
name writing is available (Modbus slave
function).
Operation mode:
RTU MASTER or RTU SLAVE
Modbus master command number:
1 to 16
VGA Video Output (/D5)
Resolution: 640 x 480 pixels (VGA)
Connector: 15 pins D-SUB (DB15HD)
Fail/Status Output (/F1)
The relay contact output on the rear panel indicates the
occurrence of CPU failure or selected status.
You can select the contents output to the two relay
output signals.
FAIL output relay:
The relay contact output on the rear panel
indicates the occurrence of CPU failure.
Relay operation: CPU normal: Energized,
CPU failure: Deenergized
Status output relay:
The relay contact output on the rear panel
indicates the occurrence of selected status
Relay operation: Status detection:
Energized

Status Description
Relay is energized when internal memory or
external storage media is in the following conditions:
Abnormality in the internal memory
When automatic saving of settings to the external
storage media is ON
• When the remaining space on the external storage
medium reaches 10%.
• When an abnormality occurs with the external
storage medium, and auto save fails
• When the external storage medium is not inserted,
operation is same as when automatic saving of
settings to the external storage media is Off
When automatic saving of settings to the external
storage media is Off
• When the remaining space on the internal memory
reaches 10%
• When the number of data file which is not saved
to external storage media exceeds 390
*Not including USB memory connected to the instrument.
Memory status
Relay energized upon A/D converter abnormality or
burnout detection
Measurement
Failure
Relay energized when communication error occurs in
the Modbus master
.
Comm. failure
Relay energized upon memory stopMemory stop
Relay energized upon any alarm occursAlarm
- Memory start and stop output
- Outputting the user locked condition
- Outputting the presence of login users
These three are only available with the /AS1
option.
Relay contact rating:
250 VDC/0.1 A (for resistance load), 250
VAC (50/60 Hz)/3A
Fail & Alarm Output Relays 22 points (/F2)
Combination of "Fail/Memory end output function" and
"Alarm output relays 22 points".
Clamped Input Terminal (/H2)
Clamped input terminal (detachable type) is used for
input terminal.
Available wire size:
0.08 to 1.5 mm2
(AWG28 to16)
Desk Top Type (/H5[ ], /H5*)
Provides carrying handle and power cord.
* In case that /P1 is specified together, /H5 must be
specified. Power terminal will be screw type and power
code will not be provided.
Mathematical Functions (/M1)
Used for calculating data, displaying trends and digital
values, and recording calculated data assigned to
channels.
Channel assignable to calculated data:
DX2004, DX2008:
Up to 12 channels (101 to 112)
DX2010, DX2020, DX2030, DX2040, DX2048:
Up to 60 channels (101 to 160)
Max. character length of expression:
120 characters
Operation:
General arithmetic operations:
Four arithmetic operations, square root,
absolute, common logarithm, natural
logarithm, exponential, power, relational
operations (>, Ն, <, Յ, =, ), logic
operations (AND, OR, NOT, XOR)
Statistical operations:
TLOG (Average, maximum, minimum,
summation and P-P value of time series
data)
CLOG (Average, maximum, minimum,
summation and P-P value of channel
series data)
Special operations:
PRE (Previous data)
HOLD(a):b (Hold data of "b" in case of "a"
is not "0")
RESET(a):b (Reset data of "b" and restart
in case of "a" is not "0")
CARRY(a):b (If "b" exceeds "a", "b-a"
becomes computation results)
Conditional operation:
[a?b:c] (Execute "b" in case of "a" is not
"0", or execute "c" in case of "a" is "0")
Constant: Up to 60 constants (K01 to K60)
Digital data input via communication:
Up to 60 data (C01 to C60)
External input:
Up to 240 data (201 to 440) (only for
external input option)
Remote status input:
Remote input status (0/1) can be used in mathematical
expression
Up to 8 inputs (D01 to D08)
Pulse input:Up to 8 pulse count input (P01 to P08, Q01
to Q08) (only for pulse input option)
Status input:
Internal switch status (S01 to S30), relay
status (I01 to I36), memory sampling status
(M01 to M12) and flag status (F01 to F08)
can be used in mathematical expression
Cu10, Cu25 RTD Input /3 leg isolated RTD Input (/N1)
This option allows Cu10 and Cu25 inputs to be added to
the standard input types.
A, B, b legs are of isolated input type for DX2010,
DX2020, DX2030, DX2040 and DX2048.
Input type Measuring range:
Temperature:
23 ؎ 2 °C
Humidity:
55% ؎ 10% RH
Report functions:
Number of report channels:
DX2004, DX2008: up to 12 channels
DX2010, DX2020, DX2030, DX2040:
up to 60 channels
Report type:
Hourly, daily, hourly + daily, daily +weekly
and daily + monthly
Operation:
Max. 4 types are selectable from average,
maximum, minimum, instantaneous and
summation
Data format:
TEXT
Excel spread sheet template function:
reports can be automatically created in
XML spread sheet format according to a
predefined spread sheet template

12
Long term rolling average:
Computation interval:
1, 2, 3, 4, 5, 6, 10, 12, 15, 20, 30 sec., 1, 2,
3, 4, 5, 6, 10, 12, 15, 20, 30, 60 min
Number of sampling:
1 to 1500
90 to 132 or 180 to 250 VAC
50/60 Hz ؎ 1%
Warm-up time:
At least 30 min.
Input Type
Measurement
range
Accuracy
guarantee
d range
16.7 ms or more
Measurement accuracy
1.67ms (Fast sampling mode)
Max. resoluti
on of digital
display
Cu10 (GE)
Cu10 (L&N)
Cu10 (WEED)
Cu10 (BAILEY)
Cu10:␣ =0.00392 at 20°C
Cu10:␣ =0.00393 at 20°C
Cu25:␣ =0.00425 at 0°C
-70 to
170°C
-75 to
150°C
-200 to
260°C
-200 to
300°C
-200 to
300°C
RTD
*1 0.1°C
±(0.8% of rdg + 5.0°C) RTD±(0.4% of rdg + 1.0°C)
±(0.5% of rdg + 2.0°C)±(0.3% of rdg + 0.8°C)
*1 Measuring current: i = 1mA
1 ⍀ or less per wire (The resistance of all
three wires must be equal.)
time or more)
؎ (0.2% of rdg + 2 digits) or less
approx. ؎ 1 °C
3 legs Isolated RTD Input (/N2)
A, B, b legs are of isolated input type.
* Can be specified only for DX2010, DX2020, DX2030,
DX2040 and DX2048.
A, B, b legs of DX2004 and DX2008 are isolated as standard.
Extended Input Types (/N3)
This option allows extra inputs types to be added to the
standard input types.
Input type Measuring range:
Temperature:
23 ؎ 2 °C
Humidity: 55% ؎ 10% RH
90 to 132 or 180 to 250 VAC
50/60 Hz ؎ 1%
Warm-up time:
At least 30 min.

Input Type
Measurement
range
16.7 ms or more
Kp vs Au7Fe 0.0 to 300.0K
0.0 to 1400.0°C
Within ±4.5K at 0 to 20K
0.1 K
PLATINEL
PR40-20
NiNiMo
W/WRe
TypeN(AWG14)
0.0 to 1310.0°C
0.0 to 2400.0°C
0.0 to 1300.0°C
±(0.25% of rdg+0.7°C)
±(0.2% of rdg+1.3°C)
±15.0°C at 0 to 400°C
±(0.2%of rdg+2.0°C) at 400
to 2400°C
±(0.5% of rdg+3.5°C)
±(0.5% of rdg+7.0°C)
±30.0°C at 0 to 400°C
±(0.4%of rdg+4.0°C) at 400
to 2400°C
Pt50 -200.0 to 550.0°C ±(0.3% of rdg+0.6°C) ±(0.6% of rdg+3.0°C)
Ni100(SAMA) -200.0 to 250.0°C ±(0.15% of rdg+0.4°C) ±(0.3% of rdg+2.0°C)
Ni100(DIN) -60.0 to 180.0°C ±(0.15% of rdg+0.4°C) ±(0.3%of rdg+2.0°C)
Ni120 -70.0 to 200.0°C ±(0.15% of rdg+0.4°C) ±(0.3% of rdg+2.0°C)
J263*B 0.0 to 300.0 K
Cu53 -200.0~550.0°C ±(0.3% of rdg +0.8°C) ±(0.3% of rdg+4.0°C)
Cu100 -50.0 to 150.0°C ±(0.2% of rdg+1.0°C) ±(0.4% of rdg+5.0°C)
Pt46 GOST -200.0 to 550.0°C ±(0.3% of rdg +0.8°C) ±(0.6% of rdg +4.0°C)
Pt25 -200.0 to 550.0°C ±(0.15% of rdg +0.6°C) ±(0.3% of rdg +3.0°C)
Pt100 GOST -200.0 to 600.0°C ±(0.15% of rdg +0.3°C) ±(0.3% of rdg +1.5°C)
Cu10 GOST -200.0 to 200.0°C ±(1.5% of rdg+3.0°C) ±(3.0% of rdg +15.0°C)
Cu50 GOST -200.0 to 200.0°C ±(0.4% of rdg +0.5°C) ±(0.8% of rdg +2.5°C)
Cu100 GOST -200.0 to 200.0°C ±(0.15% of rdg +0.3°C) ±(0.3% of rdg +1.5°C)
Pt200(WEED) -100.0 to 450.0°C ±(0.3% of rdg +0.6°C) ±(0.6% of rdg +3.0°C)
TC
RTD
*1
±(0.25% of rdg+2.3°C)
Measurement accuracy
1.67ms (Fast sampling mode)
Max. resoluti
on of digital
display
0.1 K
0.1°C
0.1°C
±(0.25% of rdg+8.0°C)
0.0 to 1900.0°C
Accuracy is not guaranteed
at 0 to 450°C
±(0.9% of rdg+3.2°C) at
450 to 750°C
±(0.9% of rdg+1.3°C) at
750 to 1100°C
±(0.9% of rdg+0.4°C) at
1100 to 1900°C
Accuracy is not guaranteed
at 0 to 450°C
±(0.9% of rdg+15.0°C) at
450 to 750°C
±(0.9% of rdg+6.0°C) at
750 to 1100°C
±(0.9% of rdg+3.0°C) at
1100 to 1900°C
*1 Measuring current: i = 1mA
XK GOST -200.0 to 600.0°C
±(0.25% of rdg +0.8°C)
±(0.25% of rdg +1.0°C) at
-200 to -100°C
±(0.5% of rdg +4.0°C)
±(0.5% of rdg +5.0°C) at
-200 to -100°C
TC: 2 k⍀ or less
RTD: 1 ⍀ or less per wire (The resistance of
all three wires must be equal.)
time or more)
TC: ؎ (0.1% of rdg + 0.05% of range) or
less Excluding the error of reference junction
compensation.
RTD: ؎ (0.2% of rdg + 2 digits) or less
(1) TC range (with variation of + 1 k⍀)
؎10 µV
(2) RTD range
approx. ؎ 1 °C
24 VDC/AC Power Supply (/P1)
Rated power supply: 24 VDC or 24 VAC (50/60Hz)
Allowable power supply voltage range:
21.6 to 26.4 VDC/AC
Power supply to ground terminal: 20 M⍀ or
greater (at 500 VDC)
Power supply to ground terminal: 500 VAC
(50/60 Hz), 1 min
Max. power consumption:
Supply voltage
24 VDC
24 VAC (50/60 Hz)
LCD off
12 VA
20 VA
Normal
20 VA
34 VA
Max.
45 VA
70 VA
Remote Control (/R1)
This option allows eight functions to be controlled
remotely by a contact input.
Please refer the part of "Event action function" for
functions to be controlled.
24 VDC transmitter power supply (/TPS4, /TPS8)
Output voltage:
22.8 to 25.2 VDC (rated load current)
Rated output current:
4 to 20 mADC
Max. output current:
25 mADC (current to guard operation
against overcurrent: approx. 68 mADC)
Allowable conductor resistance:
RL Յ (17.8 - transmitter minimum operation
voltage)/0.02 A (not include drop voltage
with load shunt resistance)
Max. length of wiring:
2 km (CEV cable)
output terminal to grand terminal more than
20 M⍀ (500 VDC)

14
Output terminal to grand terminal:
500 VAC (50/60 Hz, I = 10 mA), 1 min
Between output terminal:
500 VAC (50/60 Hz, I = 10 mA), 1 min
Easy text entry (/KB1, /KB2)
Normal operating conditions:
Ambient temperature for usage:
0 to 40 ЊC
Ambient humidity for usage:
20 to 80% RH (When 5 to 40 ЊC, no
condensation)
Ambient temperature for storage:
-10 to 60 ЊC
Power supply:
AA dry battery ؋ 2
Weight: Approx. 60 g (excluding dry battery)
Dimensions: 170 (W) ؋ 50 (H) ؋ 23.7 (D) mm
Number of units that can be controlled:
Max. 32 units by ID setting
Communication distance:
Max. 8 m (depending on battery strength
and usage area)
Orientation specifications:
Depends on battery strength & usage area
USB interface (/USB1)
USB interface specification:
Based on Rev1.1, host function
Number of ports:
2 ports (Front and rear panel)
Power supply:
5V, 500mA (for each port)*1
Available USB devices:
Keyboard: 104/89 keyboard (US) based on USB HID
Class Ver.1.1
External medium:
USB flash drive (some of USB flash drives
may not be supported by DXAdvanced)
Barcode reader:
Interface based on USB HID Class Ver.1.1
and supports standard US keyboard
*1: For low powered devices (bus power < 100 mA):
5V ؎ 5%
For high powered devices (bus power < 500 mA):
5V ؎ 10%
Devices which need more than 500 mA total bus power
for 2 ports can not be connected at the same time.
Pulse input (/PM1)
Pulse input option includes mathematical functions
option (/M1) and remote control option (/R1).
Number of inputs:
3 points (8 points are available in case of
using remote inputs)
Input format:
Photocoupler isolation (shared common)
Isolated power supply for input terminal
(approx. 5 V)
Input type:
Non-voltage contact:
Close: 200 ⍀ or less, Open: 100 k⍀ or
more
Open collector:
ON: 0.5 V or less (30 mADC), Leakage
current of OFF: 0.25 mA or less
Counting: Counts rising edges of pulses
Allowable input voltage:
30 VDC
Max. sampling pulse period:
Max.100 Hz
Minimum pulse length:
5 ms
Pulse detection period:
Approx. 3.9 ms (256Hz)
Pulse measuring accuracy:
؎1 pulse (for instantaneous mode)
Pulse count period:
Counts the number of pulse per measure-
ment period (P01 to P08) or per second
(Q01 to Q08).
Calibration correction function (/CC1)
Corrects the measurement value of each channel using
segment linearizer approximation.
Number of segment points:
2 to 16
Calibration correction control function:
You can specify how calibration correction
settings are periodically performed
External input function (/MC1)
Digital input channels via communication or Modbus
master function are extended to input data from other
instruments*.
Number of external input channels:
Up to 240 channels (channel number: 201 to 440)
* Only for DX2010, DX2020, DX2030, DX2040 and DX2048
* Fast sampling mode is not available with external input
function option.
Multi-batch function (/BT2)
This option allows to start/stop the independent data file
for each batch and creating independent data file*.
* Only for DX2010, DX2020, DX2030, DX2040 and
DX2048.
* Fast sampling mode is not available when the multi-
batch function is being used.
Number of batches:
2 to 12
Independent operation for each batch:
Memory start/stop, math reset, writing
message
Common operation for all batches:
Math start/stop, report start/stop, manual
sample, setting data save/load
Measurement interval:
Only normal mode (fast sampling mode is
not available), 1 s fastest (common for all
batches)

Data type:
Display data file or event data file only.
Trigger mode is not available for event data
file.
Data saving period:
Common for all batches
Data file:
Each display/event data file is created for
each batch
Number of group:
12 groups maximum for each batch
10 channels maximum for each group
Number of timer and match time timer:
12 timers maximum
Independent settings for each batch:
Group setting, trip line setting, file header
setting, data file name setting, text field
setting, batch number setting, lot number
setting
PROFIBUS-DP Communication Interface (/CP1)
PROFIBUS-DP master device can access to internal
data below.
Reading measurement channel data
Reading mathematical channel data
Writing communication input channel data (32 channels
maximum)
Note: When the computation function option is installed,
PROFIBUS-DP always uses communication input
channels C01-C32, therefore it is not possible to
read/write to the same communication input using
other communication functions.
Data mapping:
Buffer Description Max. size
128 byte
128 byte
Measurement data are mapped from top of buffer
Math channel data are mapped in rest of buffer
Communication input channel data are mapped
(32 channels max.)
Input
Output
Node address setting range:
0 to 125
Interface:
PROFIBUS-DP-V0 Slave
Transmission medium:
2 wires exclusive cable (2 wires for signal)
Transmission speed/distance:
9.6 kbps/1200m to 12Mbps/100m
Terminator:
Not included (external terminator is needed)
Advanced security function (/AS1)
Security and electronic record/signature functions have
been added that are compliant with the USA’s FDA title
21 CFR Part 11.
Data anti-tamper function:
Settings and measured data are saved as
encrypted binary files.
Data type:
Only for display or event
Trigger mode is not possible with event data.
Login function:
Using the login function described below,
you can enter security settings on the
instrument
- User name
- Password
- User ID (depend on setting)
User level and number of users:
System administrator: 5 users (all can be
operated)
General user: 90 users (With user
restrictions, you
can set restrictions
on performing
operations and sign
authority .)
User restrictions setting: 10 kinds (for
general users)
Password expiration time:
select form Off, 1month, 3 month, 6month
Password control function:
Logins are verified by a Kerberos authenti-
cation server* (only user name and
password)
Encryption method:
AES128-CTS-HMAC-SHA1-96
AES256-CTS-HMAC-SHA1-96
ARCFOUR-HMAC-MD5
Pre-Auth function: use
* The function has confirmed compatibility with
Windows Server2003 SP2/Windows
Server2008 SP2 Active Directory
Signature function:
After checking data that has finished being
recorded, you can add three levels of
electronic signature, select a pass/fail, and
enter comments (32 characters maximum)
Audit trail function:
The operation log, the settings change log
and the settings file when the change was
made are saved.
Individual alarm ACK function:
Alarm display and relay output can be
cancelled on individual alarms
ACK can be performed in the overview
display
Extended alarm delay time:
Alarm delay times of up to 24 hours can be
set

16
APPLICATION SOFTWARE
DAQSTANDARD
Operating environment
OS: Windows XP (Home Edition SP3, Profes-
sional SP3)*
* Except for Professional x64 Edition
Windows Vista (Home Premium SP1, SP2,
Business SP1, SP2)*
* Except for 64-bits editions
Windows 7 (Home Premium 32-bit and 64-
bit editions, Professional 32-bit and 64-bit
editions)
Windows 8 (32-bit and 64-bit editions
(Supports the desktop mode)
Windows 8 Pro 32-bit and 64-bit editions
(Supports the desktop mode)
Processor and main memory
XP: Intel Pentium III, 600 MHz or faster x64 or
x86, 128MB or more
Vista: Intel Pentium 4, 3GHz or faster x64 or x86,
2GB or more
7/8/8 Pro: 32-bit edition Intel Pentium 4, 3GHz or
faster x64 or x86, 2GB or
more
64-bit edition Intel x64 processor that is
equivalent to Intel
Pentium 4, 3 GHz or
faster, 2GB or more
Hard disk: 100MB or more of free space
Display: A video card that is recommended for the
OS and a display that is supported by the
OS, has a resolution of 1024 ϫ 768 or
higher, and that can show 65,536 colors
(16-bit, high color) or more.
Configuration software:
Setting mode:
Configuration of setting mode and basic
setting mode
Configuration via communication:
Configuration of setting mode and basic
setting mode without communication
configuration (ex. IP address)
Data viewer software:
Number of display channels:
32 channels per group, 50 groups
maximum
Viewer function
Waveform display, digital display, circular
display, list display, report display,
operation log display etc.
Signature function:
Three levels of electronic signature, select
a pass/fail, and comments (32 characters
maximum) can be inserted on the currently
displayed data file
*Applying electronic signatures to data files
created using the password management
function requires a network that can
connect with the Kerberos authentication
server set on the main unit.
Data conversion:
File conversion to ASCII, Lotus 1-2-3 or
MS-Excel format
DAQStudio (optional)
Custom display builder software
Custom display is available on DX2000 with release
number 3 or later
Operating environment
OS: Windows XP (Home Edition SP3,
Professional SP3)*
* Except for Professional x64 Edition
Windows Vista (Home Premium SP1,
SP2, Business SP1, SP2)*
* Except for 64-bits editions
Windows 7 (Home Premium 32-bit and
64-bit editions, Professional 32-bit and
64-bit editions)
Processor
XP: Intel Pentium 4, 1.6 GHz or faster x64 or
x86 processor
Vista: Intel Pentium 4, 3GHz or faster x64 or
x86 processor
7: 32-bit edition Intel Pentium 4, 3GHz or
faster x64 or x86 processor
64-bit edition Intel x64 processor that is
equivalent to Intel
Pentium 4, 3 GHz or
faster
Memory: 512 MB or more (Windows XP)
2 GB or more (Windows Vista/7)
Hard disk: 100MB or more of free space
Display: A video card that is recommended for the
OS and a display that is supported by the
OS, has a resolution of 1024 ϫ 68 or
higher, and that can show 65,536 colors
(16-bit, high color) or more.
General functions
(1) Send and receive the parts layout data of the
custom display (via Ethernet or CF card).
(2) Display the custom screens, create new custom
display and edit.
(3) Save and load the file of configured or edited
custom display data.

MODEL AND SUFFIX CODES
Suffix code DescriptionModel code Optional code
–2
–4
–3
*1 /A1, /A2, /A3, /A4, /A5, /F2 cannot be specified together.
*2 /A5 and /F1 cannot be specified together.
*3 /C2, /C3 and /CP1 cannot be specified together.
*4 /F1 and /F2 cannot be specified together.
*5 In case that 24 VDC/AC power supply (/P1) and desktop type are specified together, /H5 must be specified.
/P1 and /H5[ ] cannot be specified together.
*6 /H5[ ]
D: Power cord UL, CSA st'd
F: Power cord VDE st'd
R: Power cord SAA st'd
J: Power cord BS st'd
H: Power cord GB st'd
*7 /N2 can be specified for only DX2010, DX2020, DX2030, DX2040 and DX2048.
*8 /TPS4, /TPS8, /A5 and /F2 cannot be specified together.
*9 In case that /TPS8 is specified, combination of /A4/F1 cannot be specified together.
*10 /KB1 and /KB2 cannot be specified together.
*11 In case that /KB1 is specified, remote input terminal (438227) is included.
*12 In case that /PM1 is specified, /A5, /F2, /M1 and /R1 cannot be specified. And
combination of /A2/F1 and combination of /A4/TPS8 cannot be specified together.
*13 /MC1 can be specified for only DX2010, DX2020, DX2030, DX2040 and DX2048.
*14 /BT2 can be specified for only DX2010, DX2020, DX2030, DX2040 and DX2048.
In case that standard memory is specified, maximum number of batches is 6.
4ch, 125ms (Fast sampling mode: 25ms)
8ch, 125ms (Fast sampling mode: 25ms)
10ch, 1s (Fast sampling mode: 125ms)
400MB
CF card (with media)
English/German/French, degF, DST(summer/winter time)
Alarm output 2 points *1
Alarm output 4 points *1 *12
Alarm output 6 points *1
Alarm output 12 points *1 *9 *12
Alarm output 24 points *1 *2 *8 *12
RS-232 interface *3
RS-422A/485 interface *3
VGA output
FAIL/Status output *2 *4 *9
FAIL + Alarm output 22 points *1 *4 *8 *12
Clamped input terminal (detachable)
Desktop type (only for /P1 model, without power cable,
M4 screw type power terminal) *5
Desktop type *5 *6
Mathematical functions *12
Cu10,Cu25 RTD input/3 leg isolated RTD
3 leg isolated RTD *7
Extended input type (PR40-20, Pt50, etc.)
24VDC/AC power supply *5
Remote control *12
24VDC transmitter power supply (4 loops) *8
24VDC transmitter power supply (8 loops) *8 *9 *12
Easy text entry (with input terminal) *10 *11
Easy text entry (without input terminal) *10
USB interface
Pulse input (including remote control and mathematical functions) *12
Calibration correction function
External input function *13
Multi-batch function *14
PROFIBUS-DP communication interface *3
Advanced security function
DX2004
DX2008
DX2010
DX2020
DX2030
DX2040
DX2048
Internal memory
External media
Display language
Options /A1
/A2
/A3
/A4
/A5
/C2
/C3
/D5
/F1
/F2
/H2
/H5
/H5[ ]
/M1
/N1
/N2
/N3
/P1
/R1
/TPS4
/TPS8
/KB1
/KB2
/USB1
/PM1
/CC1
/MC1
/BT2
/CP1
/AS1
Description O SModel code
DXA120 DAQSTANDARD software Windows XP/Vista/7/8/8 Pro
DXA170 DAQStudio software (optional) Windows XP/Vista/7
DXA250 DAQManager (optional) Windows XP/Vista/7
Application Software

18
STANDARD ACCESSORIES
Product Qty
*1 For /H5[ ] option
Mounting brackets
Terminal M4 screws
Door lock key
Operation guide
DAQSTANDARD software (CD)
CF card (128MB)
Power cable *1
2
5
2
1
1
1
1
The electronic manual (CD, part no. B8706ZZ)
is available for purchase. Please contact your
nearest YOKOGAWA dealer for details.
Product Qty
Remote control terminal (438227)
AA alkali dry battery
Labels for remote control terminal
1
2
2
For / KB1 option
OPTIONAL ACCESSORIES
SpecificationProduct
Model code
(part number)
250 Ω±0.1%
100 Ω±0.1%
10 Ω±0.1%
250 Ω±0.1%
100 Ω±0.1%
10 Ω±0.1%
–
512 MB
1 GB
2 GB
–
–
For /KB1, /KB2 option
For /H2 option
For /AS1 option (CD)
Shunt resister (for M4 screw input
terminal)
Shunt resister (for clamped
input terminal)
CF card adapter
CF card
Mounting bracket
Door lock key
Remote control terminal
Removable clamp input terminal
Validation document
415920
415921
415922
438920
438921
438922
772090
772093
772094
772095
B9900BX
B8706FX
438227
A1923JT
438230

DIMENSIONS
280.2 (11.03)
295.2 (11.62)
288 (11.33)
180 (7.09)
180(7.09)
108
(4.25)
54.6 (2.15)
108
(4.25)
288(11.33)
295.2(11.62)
360MIN
(14.17)
281+2
0
361MM
(14.21)
(11.06)
281
+2
0
(11.06)
Dimentions Panel Cutout & Spacing Unit : mm
(approx.inch)
MAX 226 (8.90)
(/H2 or /PM1)
221.6 (8.72)
168 (6.61)
2 to 26
(panel thickness)
27.3
(1.07)
32.1 (1.26)
(dimension after mounting)
7.5
(0.29)
280.2(11.03)9.4(0.37)
(min. space for mounting)
Note: If not specified, the tolerance is Ϯ3%. However, for dimentions less than 10mm, the tolerance is Ϯ0.3mm.

20
282.5 (11.12)
Desk-top type Unit : mm
(approx.inch)
289.6 (11.40)
289.7(11.41)
352.8(13.89)
MAX253.3 (9.97)
(/H2 or /PM1)
245.1 (9.65)
25
(0.98)
40(1.57)287.8(11.33)
Note: If not specified, the tolerance is Ϯ3%. However, for dimentions less than 10mm, the tolerance is Ϯ0.3mm.

VGA Output Terminal (/D5)
Rear View
Ethernet
USB (/USB1)
Ethernet
USB (/USB1)
RS-422A/485 (/C3)
Power Supply Terminal
Option
Terminal
Input
Terminal
(M4 Screw Type)
Option
Terminal
Input
Terminal
(Clamped Type)
(/H2)
RS-232 (/C2),
PROFIBUS-DP(/CP1)
Power Supply
Terminal (/H5 )
RS-422-A/485 Terminal RS-232 Terminal
L N
FG SG SDB SDA RDB RDA
1
2
3
4
5
6
7
8
9
N.C.
RD
SD
N.C.
SG
N.C.
RS
CS
N.C.
12345
6789
Power Supply Terminal

22
Input Terminals
M4 Screw Terminals Clamped Terminals (/H2)
DX2010, DX2020, DX2030, DX2040
DX2048
DX2048
DX2010, DX2020, DX2030, DX2040DX2004, DX2008 DX2004, DX2008
Option Terminals

The TCP/IP software used in this product and the document for that TCP/IP software are based in part on
BSD networking software, Release 1 licensed from The Regents of the University of California.
• Daqstation, DXAdvanced and DAQstudio are registered trademark of Yokogawa Electric Corporation.
• Microsoft, MS and Windows are registered trademarks of Microsoft Corporation USA.
• Lotus and 1-2-3 are registered trademark of Lotus Development Corporation.
• Pentium are registered trademarks of Intel Corporation.
• Ethernet is a registered trademark of XEROX Corporation.
• Modbus is a registered trademark of AEG Schneider.
• PROFIBUS-DP is a registered trademark of PROFIBUS User Organization.
• EtherNet/IP is a trademark of ODVA (Open DeviceNet Vendor Association).
• Kerberos is a trademark of MIT.
• Other company and/or product names are registered trade mark of their manufactures.
Subject to change without notice

Data Acquisition Equipment for Automation and Process Control

More Related Content

What's hot (20)

Similar to Data Acquisition Equipment for Automation and Process Control (20)

More from Miller Energy, Inc. (20)

Recently uploaded (20)

Data Acquisition Equipment for Automation and Process Control