![International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
@ IJTSRD | Unique Paper ID - IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 723
The average FOS values are well within theacceptablerange.
Time(s) Min. Avg
1. 5.85e.002 2.8886
Fabrication
The results are optimized stress reduction is done by
avoiding stress concentration at sharp edges. The chassis is
fabricated and then the Go-kart vehicle is tested on track.
Figure Go-kart Chassis and final vehicle
Conclusions
The basic need of Go-kart vehicle is high power to weight
ratio and less clearance. Keeping fabrication in the mind, we
tried to make the design optimum and simple with high
strength and stability. Thus analysis is done for strength
against collisions from the front, rear as well as side. From
the above observations we can conclude that AISI 4130 is
one of the material that could be very well used for
fabrication of go-kart chassis as it gives better performance
and good weldablity in any condition. Static analysis is
performed in ANSYS software using FEA tools on thechassis
CAD model. Maximum equivalent stress(Von Mises), total
deformation or displacement and factor of safety are found
out from it. The factor of safety obtained in each analysis is
found to be greater than 1. Factor of safety is regarded the
safe limit and can be used as a criteria to make a Go- kart.
Hence we can conclude that the chassis design is safe and
stable. The design and analysis of the chassis for Go-Kart
helps to find the strength and weakness of the design and
corresponding correctionstobemadeforfabrication.Virtual
Analysis serves a good tool for finding out theweak pointsin
the design and any modifications or rectificationsthatcan be
done to the design before fabricating it.
References
[1] Thomas a Gillespie, Warren dale: SAE. , Fundamentals
of Vehicle Dynamics, 1992
[2] Shaik Himam Saheb, Govardhana Reddy, Md. Hameed
‘DESIGN REPORT OF A GO KART VEHICLE’
International Journal of Engineering Applied Sciences
and Technology, Vol. 1, Issue 9, ISSN No. 2455-2143,
Pages 95-102,2016.
[3] Kiral Lal, Abhishek O S, ‘DESIGN, ANALYSIS AND
FABRICATION OF GO-KART’ International Journal of
Scientific & Engineering Research, Volume 7, Issue 4,
429 ISSN 2229-5518, April 2016.
[4] Simranjeet Singh, Aniket Badgujar, Pushparaj Patil,
Gaurang Kadam ‘Design and Fabrication of Race Spec
Go-Kart’ American Journal of Engineering Research
(AJER) e-ISSN:2320-084 p-ISSN:2320-0936 Volume-5,
Issue-6, 2016
[5] Dr. D. Ravikanth, Dr. K. Rajagopal, Dr. V. S. S. Murty, A.
Harikrishna, International Journal of Science,
Engineering and Technology Research (IJSETR)
Volume 6, Issue 3, ISSN: 2278 -7798,March 2017.
[6] Sannake Aniket S., Shaikh Sameer R., Khandare
Shubham A., Prof. S. A. Nehatrao, “Design and Analysis
of Go-kart Chassis” IJARIIE-ISSN(O)-2395-4396,
Volume 3, Issue 2, 2017
[7] Koustubh Hajare, Yuvraj Shet, Ankush Khot, “A Review
Paper on Design and Analysis of a Go-Kart Chassis”
International Journal of Engineering Technology,
Management and Applied Sciences, ISSN 2349-4476,
Volume 4, Issue 2, Feb 2016
[8] D. Raghunandan,“DESIGNANDANALYSISOFGO-KART
CHASSIS” INTERNATIONAL JOURNAL OF
ENGINEERING SCIENCES & RESEARCHTECHNOLOGY,
Nov.2016, DOI: 10.5281/zenodo.164912
[9] Mr. Girish Mekalke “Static Analysis of a Go-Kart
Chassis”, International Journal of Mechanical and
Industrial Technology, Vol. 3, Issue 2, pp: (73-78),
Month: October 2015 - March 2016
[10] Shaik Himam Saheb ,Govardhana Hameed, “Design
Report Of A Go Kart Vehicle,”in InternationalJournalof
Engineering Applied Sciences and Technology, vol. 1,
no. 9, pp. 95-102, 2016.
[11] Suraj B Patil and Dinesh G Joshi, “Structural Analysis of
Chassis: A Review, International Journal of Research in
Engineering and Technology, Volume: 04, Issue: 04,
Apr-2015.
[12] Virendra. S. Pattanshettis, “Design and Analysis Of Go
Kart Chassis,” in International Journal of Mechanical
and Industrial Technology, vol. 4, no. 1, pp. 150-164,
September 2016.
[13] Shaik Himam Saheb, Govardhana Reddy, Md. Hameed,
Design Report of a Go Kart Vehicle, International
Journal of Engineering Applied Sciences and
Technology, Vol. 1, Issue 9, August 2016.
[14] Workability Study on Austempered AISI 1018,
IConMMEE 2018, IOP Publishing IOP Conf. Series:
Materials Science and Engineering, 2018.
[15] Kartik Kelkar, Siddhant Gawai, Tushar Suryawanshi,
Shaikh Ubaid, Rajratna Kharat, “Static Analysis of Go-
Kart Chassis,” in International Journal of Research in
Advent Technology, Special Issue National Conference
“CONVERGENCE 2017”, 09th April 2017.
[16] M. Deepak kumar, K. L. Narayan, P. S. B.Choudary, A. S.
Ganapathi, “Design and Analysis of Go-Kart Chassis
Using Catia and Ansys,” Volume 05, Issue 07, March
2018.
[17] Vijayan, S. N.,Sendhilkumar, S. and Kiran Babu K. M.,
Design And Analysis Of Automotive Chassis
Considering Cross-SectionAnd Material,” International
Journal Of Current Research, Issue, 05,pp.15697-
15701, May, 2015.](https://image.slidesharecdn.com/158designandanalysisofgo-kartchassisforfrontsideandrearimpact-190615063818/85/Design-and-Analysis-of-Go-Kart-Chassis-for-Front-Side-and-Rear-Impact-6-320.jpg)
Design and Analysis of Go Kart Chassis for Front, Side and Rear Impact
- 1. International Journal of Trend in Scientific Research and Development (IJTSRD) Volume: 3 | Issue: 3 | Mar-Apr 2019 Available Online: www.ijtsrd.com e-ISSN: 2456 - 6470 @ IJTSRD | Unique Paper ID – IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 718 Design and Analysis of Go-Kart Chassis for Front, Side and Rear Impact Chetan Mahatme1, Pratik Lande1, Surendra Nagpure1, Abhishek Pawar2, Nikhil Kharabe2 1Assistant Professor, 2 Student 1,2Mechanical Department, Rajiv Gandhi College of Engineering, Nagpur, Maharashtra, India How to cite this paper: Chetan Mahatme | Pratik Lande | Surendra Nagpure | Abhishek Pawar | Nikhil Kharabe "Design and Analysis of Go- Kart Chassis for Front, Side and Rear Impact" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456- 6470, Volume-3 | Issue-3 , April 2019, pp.718-723, URL: http://www.ijtsrd.co m/papers/ijtsrd229 73.pdf Copyright © 2019 by author(s) and International Journal of Trend in Scientific Research and Development Journal. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (CC BY 4.0) (http://creativecommons.org/licenses/ by/4.0) ABSTRACT This paper deals with Go-kart chassis building with the help of modelling software CATIA V15 and analysis of the same for front, sideandrear impact. The cassis has been designed for lightweightprofile andenginemountingof capacity 135cc. The go-kart vehicle is meant for participation in various Go-kart event organized all over the India. The preliminary test for these events is checking of 3-D model of the chassis frame and analysis of the same chassis frame under front, side and rear impact. During collision the chassis is under impact loading conditions so it has to be thoroughly analyzed for impact loads. The studies found below shades some light onhowthechassisbehavesunderimpactloading conditions. Chassis is made up of a tubular cross section pipe, fabricated assembly of EN8 grade and a few other grades. In this kart, we have used EN8 class tube with 1 inch diameter and 1.5 mm wall thickness. The results obtained for permissible stresses, Factor of safety and deformation are found to be well within range. This makes the chassis suitable for Go-kart events. The main criteria that has been focused here is maximum deformation and stress. The stresses should be well within Von-mises stress range and so as the Factor of safety. After analysis, both are found to be well within range. KEYWORDS: 3-D Modelling, analysis, stress, factor of safety, GO-kart, chassis 1. INTRODUCTION The Go-kart is a small, simple, self-propelled, lightweight vehicle for easy operation. Because of its low ground clearance, this type of vehicles are specifically designed and fabricated for racing events. The main parts involved arethe chassis, axle, steering, engine, wheel, bumpers and tyres. Its engine could be either two-stroke or four stroke engine. Chassis bears all the weight of the vehicle therefore utmost attention has to be given to chassis design and fabrication. Thus, chassis should have high strength and stability. This project involves modeling and analysis of thego-kartchassis which is constructed with the tubular AISI4130 beams. Modelling is performed on CATIA V5 software and analysis on ANSYS 19 software. The chassis is designed to withstand optimum loads applied or the loads it is going to experience while moving. 1.1. CHASSIS The chassis is the main component of go-kart vehicle as it has too bear all the weight of the vehicle. It is also subjected to various external impact loads. The loads can be applied dynamically when vehicle has collision with other bodies. Mostly the impacts occur on front, side and rear part of chassis. For vehicle moving with average 40km/h speed the impact forces are nearly 33000N. If thespeed goes above the average the impact loads nears doubles. So, in this work the analysis is carried out for average speed and average Factor of safety to be obtained is set to 2. The material selected for the chassis tubes is AISI 4130. As this materialhasCr and Mo its is readily weldable. The self-weight of chassis by providing this material to the CAD model is coming out tobe 5.06kg. So, the material is also aiding for the lightness of the chassis. This makes the Go-kart agile. 1.2. Material properties of AISI 4130 (Table-1) AISI 4130 alloy steel contains chromium and molybdenum as strengthening agents. It has low carbon content, and hence it can be welded easily in any condition hence highly suitable for Go-kart Chassis. IJTSRD22973
- 2. International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470 @ IJTSRD | Unique Paper ID - IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 719 1.3. Table 2 Carbon Steel AISI4130 Chemical Composition Standard ASTM A29 Grade 4130 C 0.28-0.33 Mn 0.40-0.60 P 0.035 S 0.040 Si 0.15-0.35 Cr 0.80-1.10 Mo 0.15-0.25 1.4. Chassis Dimensions (Table-2) Parameters Values Mass of vehicle (with driver) 130kg Radius of tyre 5.5 inches Vehicle Length 78 Inch Vehicle wheel base 48 inch Vehicle width 40 inch Tube dimension 1 inch Pipe thickness 1.5 mm 1.5. Engine and transmission (Table-3) Go-kart has usually small engine. So, to increase power to weight ratio the vehicle weight has to be as minimum as possible. The engine specifications for various Go-kart events is always specified. In this kart, we use a Bajaj Discover 134.6cc, 4-valve, 4-stroke single cylinder petrol engine, air cooled, which produces about 12.8 BHP of power at 9000rpm, maximum torque is 11 N-m @7000rpm. The power from the engine is transmitted to the rear twowheels using chain drive. Betweenthesetwo,transmission systemis incorporated. This plus weight of driver is the total weight on the chassis. Engine specification: Displacement 134.6cc No. of cylinders 1 No. of Gears 5 Max Power 12.8Bhp at 9000rpm Max Torque 11Nm at 7000rpm Cooling Air cooling Bore 54mm Stroke 58.8mm Engine valves 4 VALVES, 4 STROKE 2. DESIGN METHODOLOGY Design methodology involves various steps to be taken in right sequence to generate a fully functionaldesign. Here, for prototype building CAD softwares are used. Material selection is done and applied to the CAD model. Analytical calculation are done are checked weith analysis results of ANSYS. Changes were made to make a final design. This design is then fabricated. 2.1. Methodology The following design and analysis methodology has been followed to reach to the conclusion that the Go-kartissafe to develop and drive. The detailed work flow is depicted in pictorial representation below: 2.2. CHASSIS DESIGN The chassis has been modelled using CATIA V5 by using tubular cross section beams. The models are as shown in various views below: Isometric View Top View Right Side View 2.3. Finite Element Analysis The CAD Model of the chassis is then Analyzed in ANSYS software for front, side and rear impact. Vehicle speed is taken as 40km/h. So, corresponding impact force on static body of chassis is calculated with the help of impulse- momentum principle of collision of bodies. The chassis is considered to be in dynamic equilibrium condition.Meshing and refinement is reiterated to get best optimum results.
- 3. International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470 @ IJTSRD | Unique Paper ID - IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 720 Chassis specification in ANSYS 19 is as follows: The analysis meshing and results obtained are as follows: 2.3.1. Front Impact For front impact meshing is done bytakingmeshqualityinto consideration. Details of meshing is as follows: Impact loading is taken as follows: Figure Front Impact (Total Deformation) The average deformation values are well within the acceptable range. Time(s) Min.(mm) Avg (mm) 1. 0 3.5877 Figure Front Impact (Von-Mises Stress) The average stress values are well within the acceptable range. Time(s) Min.(MPa) Avg (MPa) 1. 0 223.93
- 4. International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470 @ IJTSRD | Unique Paper ID - IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 721 Figure Front Impact (factor of safety) The average FOS values are well within theacceptablerange. Time(s) Min. Avg 1. 0.17567 2.5828 2.3.2. Side Impact For side impact meshing is done by taking mesh quality into consideration. Details of meshing is as follows: Impact loading is taken as follows: Figure Side Impact (Total Deformation) The average deformation values are well within the acceptable range. Time(s) Min.(mm) Avg (mm) 1. 0 0.24106 Figure Side Impact (Von-Mises Stress) The average stress values are well within the acceptable range. Time(s) Min.(MPa) Avg (MPa) 1. 0 50.108 Figure Side Impact (Factor of Safety)
- 5. International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470 @ IJTSRD | Unique Paper ID - IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 722 The average FOS values are well within theacceptablerange. Time(s) Min. Avg 1. 0.39372 8.4879 2.3.3. Rear Impact For rear impact meshing is done by taking mesh quality into consideration. Details of meshing is as follows: Impact loading is taken as follows: Figure Rear Impact (Total Deformation) The average deformation values are well within the acceptable range. Time(s) Min.(mm) Avg (mm) 1. 0 3.3643 Figure Rear Impact (Von-Mises Stress) The average stress values are well within the acceptable range. Time(s) Min.(MPa) Avg (MPa) 1. 0 281.97 Figure Rear Impact (Factor of Safety)
- 6. International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470 @ IJTSRD | Unique Paper ID - IJTSRD22973 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 723 The average FOS values are well within theacceptablerange. Time(s) Min. Avg 1. 5.85e.002 2.8886 Fabrication The results are optimized stress reduction is done by avoiding stress concentration at sharp edges. The chassis is fabricated and then the Go-kart vehicle is tested on track. Figure Go-kart Chassis and final vehicle Conclusions The basic need of Go-kart vehicle is high power to weight ratio and less clearance. Keeping fabrication in the mind, we tried to make the design optimum and simple with high strength and stability. Thus analysis is done for strength against collisions from the front, rear as well as side. From the above observations we can conclude that AISI 4130 is one of the material that could be very well used for fabrication of go-kart chassis as it gives better performance and good weldablity in any condition. Static analysis is performed in ANSYS software using FEA tools on thechassis CAD model. Maximum equivalent stress(Von Mises), total deformation or displacement and factor of safety are found out from it. The factor of safety obtained in each analysis is found to be greater than 1. Factor of safety is regarded the safe limit and can be used as a criteria to make a Go- kart. Hence we can conclude that the chassis design is safe and stable. The design and analysis of the chassis for Go-Kart helps to find the strength and weakness of the design and corresponding correctionstobemadeforfabrication.Virtual Analysis serves a good tool for finding out theweak pointsin the design and any modifications or rectificationsthatcan be done to the design before fabricating it. References [1] Thomas a Gillespie, Warren dale: SAE. , Fundamentals of Vehicle Dynamics, 1992 [2] Shaik Himam Saheb, Govardhana Reddy, Md. Hameed ‘DESIGN REPORT OF A GO KART VEHICLE’ International Journal of Engineering Applied Sciences and Technology, Vol. 1, Issue 9, ISSN No. 2455-2143, Pages 95-102,2016. [3] Kiral Lal, Abhishek O S, ‘DESIGN, ANALYSIS AND FABRICATION OF GO-KART’ International Journal of Scientific & Engineering Research, Volume 7, Issue 4, 429 ISSN 2229-5518, April 2016. [4] Simranjeet Singh, Aniket Badgujar, Pushparaj Patil, Gaurang Kadam ‘Design and Fabrication of Race Spec Go-Kart’ American Journal of Engineering Research (AJER) e-ISSN:2320-084 p-ISSN:2320-0936 Volume-5, Issue-6, 2016 [5] Dr. D. Ravikanth, Dr. K. Rajagopal, Dr. V. S. S. Murty, A. Harikrishna, International Journal of Science, Engineering and Technology Research (IJSETR) Volume 6, Issue 3, ISSN: 2278 -7798,March 2017. [6] Sannake Aniket S., Shaikh Sameer R., Khandare Shubham A., Prof. S. A. Nehatrao, “Design and Analysis of Go-kart Chassis” IJARIIE-ISSN(O)-2395-4396, Volume 3, Issue 2, 2017 [7] Koustubh Hajare, Yuvraj Shet, Ankush Khot, “A Review Paper on Design and Analysis of a Go-Kart Chassis” International Journal of Engineering Technology, Management and Applied Sciences, ISSN 2349-4476, Volume 4, Issue 2, Feb 2016 [8] D. Raghunandan,“DESIGNANDANALYSISOFGO-KART CHASSIS” INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCHTECHNOLOGY, Nov.2016, DOI: 10.5281/zenodo.164912 [9] Mr. Girish Mekalke “Static Analysis of a Go-Kart Chassis”, International Journal of Mechanical and Industrial Technology, Vol. 3, Issue 2, pp: (73-78), Month: October 2015 - March 2016 [10] Shaik Himam Saheb ,Govardhana Hameed, “Design Report Of A Go Kart Vehicle,”in InternationalJournalof Engineering Applied Sciences and Technology, vol. 1, no. 9, pp. 95-102, 2016. [11] Suraj B Patil and Dinesh G Joshi, “Structural Analysis of Chassis: A Review, International Journal of Research in Engineering and Technology, Volume: 04, Issue: 04, Apr-2015. [12] Virendra. S. Pattanshettis, “Design and Analysis Of Go Kart Chassis,” in International Journal of Mechanical and Industrial Technology, vol. 4, no. 1, pp. 150-164, September 2016. [13] Shaik Himam Saheb, Govardhana Reddy, Md. Hameed, Design Report of a Go Kart Vehicle, International Journal of Engineering Applied Sciences and Technology, Vol. 1, Issue 9, August 2016. [14] Workability Study on Austempered AISI 1018, IConMMEE 2018, IOP Publishing IOP Conf. Series: Materials Science and Engineering, 2018. [15] Kartik Kelkar, Siddhant Gawai, Tushar Suryawanshi, Shaikh Ubaid, Rajratna Kharat, “Static Analysis of Go- Kart Chassis,” in International Journal of Research in Advent Technology, Special Issue National Conference “CONVERGENCE 2017”, 09th April 2017. [16] M. Deepak kumar, K. L. Narayan, P. S. B.Choudary, A. S. Ganapathi, “Design and Analysis of Go-Kart Chassis Using Catia and Ansys,” Volume 05, Issue 07, March 2018. [17] Vijayan, S. N.,Sendhilkumar, S. and Kiran Babu K. M., Design And Analysis Of Automotive Chassis Considering Cross-SectionAnd Material,” International Journal Of Current Research, Issue, 05,pp.15697- 15701, May, 2015.