Design and Materials Selection: analysis of similar sanitary pads for daily use

M Pohlmann. Int. Journal of Engineering Research and Application www.ijera.com
ISSN : 2248-9622, Vol. 6, Issue 11, ( Part -2) November 2016, pp.74-79
www.ijera.com 74 | P a g e
Design and Materials Selection: analysis of similar sanitary pads
for daily use
M Pohlmann
PPGE3M, Universidade Federal do Rio Grande do Sul (UFRGS), Brazil
ABSTRACT
Hygiene practices have effects on vulvovaginal microbiota. Specific products for intimate female hygiene are
available in the market, such as the sanitary pads. Since these pads were introduced in the market , they became
the focus of research that seek to improve their shape, manufacturing processes and the properties of materials
used in order to provide more benefits to users. Thus, the present study aimed to characterize the fabrics used in
daily sanitary pads, focusing on the development of future products. The spectra generated by FTIR/ATR
suggest that the samples were composed of polypropylene. The photomicrographs showed that the polymeric
outer layer was made of nonwoven fabric manufactured by spunbond and point bonding processes.
Keywords: product design, material selection, analysis of similar sanitary pads.
I. INTRODUCTION
The vulva is a complex structure that
provides the interface between external environment
and the internal portion of the female genitals. Due
to exposure, the vulva is susceptible to diseases that
may even compromise the female reproductive
development and functions. One of the defense
mechanisms in the prevention of infections in this
area is the composition of the vaginal microbiota.
Several factors, including hygiene practices, may
contribute to the increased instability of the vaginal
ecosystem.
For women, these practices include bathing
and drying of the whole body and hygiene of the
genital area after urination/defection and during
menstruation. In a study with American women,
Czerwinski [1] pointed out that most of them make
use of sanitary pads for daily genital hygiene.
Many doctors claim that the daily use of
sanitary pads may prevent proper ventilation,
increase the local temperature, and change vaginal
pH, potentially leading to the development of
vulvovaginal infections. However, new researches
have indicated that a continuous daily use of sanitary
pads does not increase recurrences of vulvovaginitis,
bacterial vaginosis, vulvovaginal irritation or
inflammation [2-5].
Research conducted on the textile sector
may improve the properties of materials and
processes used in sanitary pads for everyday use. In
recent years, researchers have investigated the use of
functional textiles in the areas of health, hygiene and
beauty. Textile materials that have in their
composition elements of body care, fitness and
health are known as "cosmetic textiles". On contact
with human body and skin, these textiles transfer an
active substance for cosmetic purposes [6-13].
Therefore, the present study aimed to
characterize the materials used in the top sheet of
sanitary pads available in the market. The results
obtained from the analysis can be used as a future
reference for processing and for materials selection
used in products with similar characteristics.
Nevertheless, the knowledge of some physic-
chemical and morphological properties of sanitary
pads for daily use can be helpful in determining
procedures for the improvement of these products
design.
II. THE EVOLUTION OF SANITARY
PADS
Sanitary pads have been used for thousands
of years. These pads were made of soft material to
absorb menstrual discharge. The ancient Greek
physician Hippocrates mentioned in his manuscripts
the use of tampons. For centuries, the methods of
menstrual protection have not evolved: women often
used strips of cloth or rags to provide menstrual
protection which they would wash and reuse [14].
The first disposable sanitary pad was
created (without success) by Johnson & Johnson in
1896. The Kimberly-Clark Company put Kotex on
the market in 1921. Meanwhile, Johnson & Johnson
introduced Modess®. These disposable absorbents
were extended front and back so as to fit through
loops in a special girdle or belt worn beneath
undergarments. The first major improvement in
disposable sanitary pads came around 50 years later
when an adhesive was included underside the
product to ensure it would remain in the same
position [3, 14-22].
With the technological advances, the
industry started to manufacture thinner pads made of
cotton wool mixed with special polymer crystals
RESEARCH ARTICLE OPEN ACCESS

(polyacrylamide and sodium polyacrylate) designed
to absorb liquid. Once liquid enters the pads, the
polymer crystals absorb it turning it into a gel-like
substance and trapping it inside. The next step was
the development of more comfortable and safer
products. In the 1990s, the industry introduced
innovations such as wings on maxi pads, with
wraparound edges that fold under to fit multiple
panty style [3, 21].
Recently, several studies have been carried
out in order to improve the characteristics of sanitary
pads. One of the main concerns is to lock away odor
[23-31]. Improvements are also being made with
regard to the absorption of fluid [32, 33].
III. MATERIALS AND METHODS
Fig. 1 shows the basic structure of sanitary
pads. It consists of a top sheet layer that allows the
passage of organic fluids, an absorbent layer and an
underlying adhesive layer used as structural support.
Fig. 1 Basic structure of sanitary pads.
The present study was carried out using six
top sheet of sanitary pads available in the market.
The materials characterization was performed by the
analysis of the chemical composition, morphology
and the rate of capillary absorption.
The chemical composition analysis was
performed using the technique of Attenuated Total
Reflection in conjunction with Fourier Transform
Infrared Spectroscopy (ATR-FTIR). Sixteen
cumulative readings were made from each sample,
over the wavelength range of 4000-650 cm-1
, in
transmission mode (Perkin-Elmer® Spectrum 100).
The top sheets morphological analysis was
performed using a Hitachi® TM 3000 Scanning
Electron Microscope (SEM). The magnified images
(X50) allowed the analysis of the structure and
manufacture aspects of the material under study.
The rate of capillary absorption of water is
among the tests prepared by the Brazilian Standards
NBR-13735:2006 [34] that proved to be adequate to
evaluate this parameter in nonwoven. This material
is often used in products that are directly in contact
with the skin, therefore, it is of fundamental
importance that the liquid moisture (mucous, urine,
blood or sweat) flows quickly through the
nonwoven, reducing the moisture built up in the
microclimate. So the top sheet samples were
partially immersed in distilled water at selected
times (10, 30 and 60 seconds) to measure the height
attained by the water.
IV. RESULTS AND DISCUSSION
For the trials, it was necessary to separate
the top sheet layer from the other parts of the
sanitary pads samples. Most of the six pads analyzed
(samples 2, 3, 5 and 6) had only a few adherence
points between the top sheet and the absorbent layer,
which was thicker and slightly compressed. In
contrast, samples 1 and 4 had a more compressed
and homogeneous absorbent layers. It should be
observed that the total thickness of the sanitary pads
was determined mostly by the thickness of the
absorbent layer. The process of separation was made
difficult by these characteristics, and the top sheet
samples were contaminated with the absorbent
material (cellulose). Moreover, it was observed that,
in the nonwoven, the web was stretched transversely
in samples 1 and 2, and in the remaining ones,
longitudinally.
After the samples of top sheet were
separated from the sanitary pads, the analysis of the
chemical composition was performed. The spectra
generated by ATR-FTIR from the scan area (Fig. 2)
showed that samples 1, 3, 4, 5 and 6 were composed
of polypropylene (C3H6)n. Samples 2 and 6 showed
the presence of cellulose (C6H10O5)n. It was
probably some residue from the absorbent layer.

Fig. 2 Spectra of chemical composition of the sanitary pads top sheet generated by FTIR/ATR spectroscopy.
The interpretation was based on the scheme prepared by Lopes; Fascio [35], which corroborate those used as
reference (cellulose and polypropylene).
The SEM analyses made it possible to identify the
morphological aspects and the manufacturing
process of sanitary pads top sheet. The material
photomicrographs (Fig. 3) magnified 50X revealed
plates of aggregate material, apparently bonded. This
is one of the morphological characteristics of
materials known as nonwoven fabrics (NWF).

Fig. 3 Photomicrographs of sanitary pads top sheet.
Arrows indicate cotton fibers intertwined to
polypropylene; circles show contaminant particles.
The NWFs are widely applied in personal
care and hygiene products due to their ability to
absorb moisture. NWFs are disposable, comfortable
and can be fabricated faster. Although the NWFs are
made up of fibers and filaments, these materials
differ from textile fabrics, because their fibers are
not knitted, woven or plaited [36-39]. In accordance
to Brazilian Standards [40], “the nonwoven is a flat,
flexible and porous structure consisting of a mat or
veil of fibers or filaments directionally or randomly
oriented, consolidated by mechanical means
(friction) and / or chemical (adhesion) and / or
thermal (cohesion) and combinations thereof”.
SEM photomicrographs of the analyzed
material showed that it was manufactured by
spunbond and point bonding processes, as described
by Gupta; Smith [20]. It was also observed that the
samples were contaminated by small particles.
However, the analysis of the substrate morphology
was not able to determine whether it was dust or
cellulose from the absorbent outer layer.
Additionally, with the exception of sample 1, the
other samples had interwoven cotton fibers in their
structure. The cotton fibers have a flat irregular
shape and can be easily visualized in the midst of the
regular polypropylene fibers.
According to Alcântara; Daltin [38], cotton
consists of mainly cellulose, with a large number of
hydroxyl groups, and is highly absorbable due to its
hydrophilic nature. Therefore, it is believed that the
incorporation of this material is intended to improve
both the tactile and the absorption aspects.
To obtain the rate of capillary absorption,
the NWF samples were partially immersed in
distilled water at selected times (10, 30 and 60
seconds) to measure the height attained by the water.
Three specimens were tested for each sample. Fig. 4
shows the mean values obtained.
In general, samples 1 and 2 presented
higher capillary rates, absorbing up to 1.66 mm in
60s.The maximum height of capillary rise in the
other samples was 0.66 mm. It is believed that this
result is due to the fact that sample 2 had ingredients
that could interfere with water absorption. However,
no relationship was found between the composition
of sample 1 and the amount of water absorbed.
Moreover, it was observed that there was not a
pattern of water absorption by capillarity of the
evaluated materials.

Fig. 4 Capillary rate measurement (mm) of sanitary
pads top sheets. It was taken at 10, 30 and 60
seconds. Each bar corresponds to the mean of three
samples.
V. CONCLUSIONS
The spectra generated by ATR-FTIR
showed that samples 1, 3, 4, 5 and 6 were composed
of polypropylene. Samples 2 and 6 showed the
presence of cellulose (C6H10O5)n, which was
probably some residue from the inner lining. The
SEM photomicrographs of the analyzed material
showed that the top sheets were composed by
nonwoven fabric and they were manufactured by
spunbond (a direct conversion of a polymer into
continuous filaments) and point bonding (a process
of binding thermoplastic fibers into a nonwoven
fabric by applying heat and pressure). Contaminants
and particles of cotton fibers were found in most
samples. There was not a pattern of water absorption
by capillarity of evaluated materials.
The present study described some of the
physicochemical and morphological characteristics
of the materials used in sanitary pads top sheet for
daily use. The data obtained from the analyses can
assist in the design, manufacturing processes and
material selection of future projects for intimate
hygiene products.
ACKNOWLEDGEMENTS
We gratefully acknowledge the financial support
provided by CAPES. We also thank the Laboratory
of Design and Materials Selection (LdSM /
UFRGS).
REFERENCES
[1] B.S. Czerwinski, Feminine hygiene
considerations for the space environment, in
D. Taylor & N.E Woods (Ed.), Menstruation,
health, and illness (Washington, DC:
Hemisphere Publishing Corporation, 1991)
65-71.
[2] M. Farage, M, Bramante, Y. Otaka, J. Sobel,
Do panty liners promote vulvovaginal
candidiasis or urinary tract infections? A
review of the scientific evidence, European
Journal of Obstetrics & Gynecology and
Reproductive Biology, 132, 2007, 8–19.
[3] R.L.G. Amaral, P.C. Giraldo, J. Eleutério Jr,
A.K.S. Gonçalves, J. Beghini, J.R.E. Gabiatte,
Grau de satisfação de mulheres que usaram
absorvente higiênico “respirável” externo por
75 dias consecutivos, J bras Doenças Sex
Transm, 23(1), 2011, 23-27.
[4] P.C. Giraldo, R.L.G. Amaral, C. Juliato, J.
Eleutério Jr, E. Brolazo, A.K.S. Gonçalves,
The effect of “breathable” panty liners on the
female lower genital tract, International
Journal of Gynecology and Obstetrics, 115,
2011, 61–64.
[5] A.C. Pontes, R.L.G. Amaral, P.C. Giraldo, J.
Beghini, H.P.D. Giraldo, E.S. Cordeiro, A
systematic review of the effect of daily panty
liner use on the vulvovaginal environment,
International Journal of Gynecology and
Obstetrics, 127, 2014. pp. 1–5.
[6] G. Fisher, Medical and Hygiene Textiles:
Continuing in Good Health, Tech. Textiles
Int., 11(3), 2002, 10–16.
[7] Anon, Microencapsulation: for Enhanced
Textile Performance, Perform. Apparel
Mark., 12, 2005, 21–39.
[8] R. Czajka, Development of Medical Textile
Market, Fibre Textiles East. Eur., 13(1),
2005, 13–15.
[9] C.W. Kan, C.W.M. Yuen, Cosmetic Textiles,
Textile Asia, 36(6), 2005, 29–35.
[10] C.X. Wang, S.L. Chen, Aromachology and its
application in the textile field, Fibres Textiles
East Eur, 13(6), 2005, 41-44.
[11] S.Y. Cheng, C.W.M. Yuen, C.W. Kan,
K.K.L. Cheuk, J.C.O. Tang, Systematic
characterization of cosmetic textiles, Textile
Research Journal, 80(6), 2010, 524–536.
[12] M.K. Singh, V.K. Varun, B.K. Behera,
Cosmetotextiles: State of Art, Fibres &
Textiles in Eastern Europe, 19(4), 2011, 27-
33.
[13] D. Bhargava, S. Jahan, Cosmetic textile: an
innovative alliance of textile and cosmetics,
China Textile Science, 2012, 41-45.
[14] Inmetro. Absorventes Higiênicos (Externos e
Intravaginais), 1998, Available in
http://www.in
metro.gov.br/consumidor/produtos/absorvente
s.asp#normas, Accessed in nov. 7th 2014.
[15] A.M. Cottenden, Incontinence pads: clinical
performance, design and technical properties,
J. Biomed. Eng., 10, 1988, 506-514.
[16] L. Hellstrom, N. Zubotikin, P. Ekelund, M.E.
Larson, I. Milsom, Selecting the correct
incontinence pad in nursing home patients by
pad weighing, Archives of Gerontology and
Geriatrics, 18, 1994, 125-132.

[17] J. Backer, P. Norton, Evaluation of absorbent
products for women with mild to moderate
urinary incontinence, Applied Nursing
Research, 9(1), 1996, 29-36.
[18] D.K. McClish, J.F. Wyman, P.G. Sale, J.
Camp, B. Earle, Use and costs of
incontinence pads in female study volunteers,
JWOCN, 4(26), 1999, 207-213.
[19] L. Wang, Market Share Sanitary Napkins. In
K. Osada, Y. Kajiwara, Y (Ed.), Gels
Handbook (San Diego: Academy Press,
2001).
[20] B.S. Gupta, K.K. Smith, Nonwovens in
Absorbent Materials, .in Chatterjee, Gupta
(Ed.), Absorbent Technology (Elsevier, 2002,
349-388).
[21] A.B. Sanches, Aplicação da análise do valor
global de um resíduo na fabricação de
produtos descartáveis higiênicos em uma
empresa do Rio Grande do Sul, masters diss.,
Universidade Federal do Rio Grande do Sul,
2004.
[22] M.A. Farage, L. Lennon, F. Ajayi, Products
used on female genital mucosa, Curr Probl
Dermatol., 40, 2011, 90-100.
[23] Procter & Gamble CO, Absorbent article for
use as e.g. tampon comprises at least an
oxidizing agent with specified reduction
potential together with a hemolytic agent,
WO200051655-A1, 8 set. 2000A.
[24] Procter & Gamble CO, Absorbent article for
use e.g. sanitary napkin containing an odor
control system comprises at least one
oxidizing agent together with at least one
chelating agent, WO200051651-A1, 8 set.
2000B.
[25] Procter & Gamble CO, Articles such as
absorbent disposable article having odor
control material for controlling odor from
bodily fluids comprise peroxyacid,
WO200051657-A1, 8 set. 2000C.
[26] Procter & Gamble CO, Articles such as
disposable absorbent article having odor
control system for controlling odors from
bodily fluids comprise water soluble oxidiz-
ing agent(s) and emulsifier, WO200051653-
A1 08 set. 2000D.
[27] Procter & Gamble CO, A. Di Cintio, A.
Pesce, G. Carlucci, D. Talone, Disposable
absorbent articles such as pantiliners,
sanitary napkins, diaper, incontinent pad,
human or animal waste management device,
comprises cationic polysaccharide and acidic
pH buffering material, EP1149593-A1, 31
out. 2001.
[28] Procter & Gamble CO, Article such as
disposable absorbent article, sanitary napkin,
pantiliner, tampon, diaper, incontinent pad,
breast pad, perspiration pad, comprises
chitosan material and ionic absorbent gelling
material, KR2002093080-A, 12 dez. 2002.
[29] Yi Chia Bao Biochemical Technology CO,
Additive for sanitary napkin, acting as a
bacteriostatic, analgestic, deodoring,
antipruritic, and soothing agent comprises
e.g., tea tree extract, anise extract and
borneol, TW200418533-A. 01 out. 2004.
[30] P&G, Absorbent article having a lotion
composition and a method of making same,
WO2014100068 A1, 26 jun. 2014.
[31] Sca Hygiene Prod Ab, Hygiene product such
as panty liner, sanitary towel or incontinence
pad, WO2014/092623 A1, 19 jun. 2014.
[32] Kimberly-Clark Worldwide INC, Preparation
of composite for use in absorbent article,
involves covering superabsorbent material
with intimately associated coating material by
introducing respective particles separately
into flowing gas stream, WO200062922-A1,
26 out. 2000A.
[33] Kimberly-Clark Worldwide INC,
Superabsorbent-containing composite for use
in disposable absorbent articles, comprises
stiff-gelling superabsorbent particles covered
with intimate layer of coating material
particles, WO200062825-A2, 26 out. 2000B.
[34] ABNT, NBR-13735: Nãotecido –
Determinação da absorção (Rio de Janeiro,
2006).
[35] W.A. Lopes, M. Fascio, Esquema para
interpretação de espectros de substâncias
orgânicas na região do infravermelho, Quim.
Nova, 4(27), 2004, 670-673.
[36] A.H. Drelich, Nonwoven Textile Fabrics
(Staple Fibers), Encyclopedia of Chemical
Technology, 16, 1981, 104-124.
[37] A.T. Purdy, Developments in Nonwoven
Fabrics, Textile Progress, 12, The Textile
Institute, 1983.
[38] M.R. Alcântara, D. Daltin, A química do
processamento têxtil, Química Nova, 19(3),
1996, 320-330.
[39] I.M. Hutten, Raw materials for nonwoven
filter media, Handbook of nonwoven filter
media (Elsevier Science, 2007, 103-194).
[40] ABNT. NBR-13370: Nãotecido –
Terminologia. (Rio de Janeiro, 2002).

Design and Materials Selection: analysis of similar sanitary pads for daily use

More Related Content

What's hot (10)

Similar to Design and Materials Selection: analysis of similar sanitary pads for daily use (18)

Recently uploaded (20)

Design and Materials Selection: analysis of similar sanitary pads for daily use