Drilling methods by RAJESH GUPTA

DRILLING METHODS
This continuing education unit reviews drilling methods
common to drillers, with an emphasis on water well
drilling methods. For completeness mention is made of
methods or tools used in the oil & gas industry. Often
methods or tools first employed in the oil or gas drilling
industry eventually find their way into the water well
drilling field. As well mention is made of drilling
methods employed in the geotechnical or environmental
drilling sector. However the coverage of the methods
and tool of the geotechnical or environmental sector is
not exhaustive.
Many drillers adopt their chosen method of both hole-
making and hole clearing and become experts over time.
Long and successful careers are had by working within
the method of drilling/hole clearing chosen. These
drillers identify themselves by their chosen methods:
“cable tool driller” “mud rotary driller,”
“environmental/geotechnical driller.” Large companies
look for these specialists when seeking new employees.
Other drillers, by choice, or happenstance are exposed
to several methods of making hole and hole clearing.
These drillers become comfortable using different
approaches depending upon hole size, engineering
specifications, equipment availability and geology.
The material below reviews the range of hole making
and hole clearing approaches in common use in the
drilling industry.
Hole making methods

Making hole includes breaking rock in consolidated
formations and stirring sediments in unconsolidated
formations. While hole making is most commonly
carried out by mechanical means, other means may also
be employed such as high frequency vibration and
hydraulic pressure.
MECHANICAL HOLE MAKING METHODS
CABLE TOOL
Cable tool had its beginnings 4000 years ago in China.
It was the earliest drilling method and has been in
continuous use for about 4000 years. The Chinese used
tools constructed of bamboo and well depths of 3000 ft.
are recorded. However, wells of this depth often took
generations to complete.
Cable tool rigs are sometimes called pounders,
percussion, spudder or walking beam rigs. They
operate by repeatedly lifting and dropping a heavy
string of drilling tools into the borehole. The drill bits
breaks or crushes consolidate rock into small
fragments. When drilling in unconsolidated formations,
the bit primarily loosens material.

Water, either from the formation or added by the driller,
mixes the crushed or loosened particles into a slurry at
the bottom of the borehole. An experienced cable tool
driller feels when the accumulated slurry has reached
the point where it is reducing bit penetration to an
unacceptably slow level. At this point slurry is removed
from the borehole by a bailer. Once the slurry is
removed, the bit is reinserted into the hole and drilling
continues.
Cable Tool Drill String Components:
For a cable tool drill to operate the drill string must have
these four components:
• Drilling cable - lifts tools, turns tools, controls tool
motion.
• Swivel socket - connects cable to tools, allows
cable to unwind.
• Drill stem - provides weight, steadies and guides
bit.
• Drill bit - penetrates formation, crushes and reams,
mixes cuttings. Many cable tool drillers now
employ Tungsten Carbide studded bits to aid in
hard rock penetration.

Tool joints connect the drill string components.
Depending on formation the driller may add drilling jars
to the drill string. The hammering action provided by

the jars frees tools that become jammed. Jars play no
part in the drilling process.
Cable Tool Bailer

A bailer is run on a separate bailing line and is inserted
after the drill string is removed from the hole. The
bailer is used to remove slurry from the hole so that
efficient penetration can continue.
Cable Tool Casing Driving Equipment
The driving of casing is an integral part of cable tool
drilling. The driving force is provided by a drive clamp
attached to the drill string. A wrench square is forged in
the drill stem to allow for the attachment of the drive
clamp.

A drive shoe is attached to the bottom of the first length
of casing to be driven. The drive shoe is manufactured
with a hardened cutting surface at the leading edge.
When fully driven into a consolidated formation a seal is
created between the drive shoe and the formation.

A drive head is fitted to the top of the casing to protect it
against damage when being driven.
Cable Tool Operation
The drilling motion of the cable tool drilling machine
must be synchronized with the gravity fall of the tools
for effective penetration. Effective drilling action is
obtained when the engine speed is synchronized with
the fall of the tools and the stretch of the cable, while
paying out the correct amount of cable to maintain
proper feed of the bit. A shock absorber is installed at
the crown sheave to provide resiliency in the system.
The shock absorber dampens vibration and protects the
derrick and machine from severe shock stresses. The
shock absorbers rebound helps to lift the tools sharply
after they strike bottom.
Every cable tool machine has certain limits as to the
depth and diameter of boreholes it is capable of drilling.
This limit is a function of the total weight of the drill
string plus the cable needed to drill to either maximum
depth or maximum casing diameter.
The usual process is to drive the casing initially using
the hammering action of the drive clamps attached to
the wrench square near the top of the drill stem. The
clamps act as the hammer face and the tools provide the
weight for driving the casing. After the casing is driven
into the formation, the material is removed by inserting
the bit, adding water and operating the drill bit until a
slurry is formed from the cuttings. The bailer is then
used to remove the slurry and this process is repeated

with the driving of casing the insertion of the drill bit,
the operation of the bit until a slurry is formed and the
bailing of the slurry until the casing reaches a desired
depth.
While drilling, a depth may be reached where casing
cannot be driven further without risking damage to it. If
this point is reached and sufficient water has not yet
been found, the casing diameter will then be reduced
and drilling will continue inside the smaller casing.
Drillers anticipating the need to telescope casing
downward will begin drilling a borehole of a larger size
to accommodate telescoping down during the drilling
process.
Advantages of the cable tool:
1. Highly suitable for remote settings. The cable tool’s
low fuel consumption, small needs for water and
other materials and reliability make it an excellent
choice for remote site locations.
2. Low capital investment and cheap maintenance.
Capital costs of new cable tool rigs are generally
significantly less than the costs of new rotary drilling
machines of similar capacity. As well, cable tool
maintenance is less expensive than parts for the less
mechanical, more hydraulically equipped rotary
systems.
3. Particularly suited to water poor areas. Cable tool
drilling more easily identifies each water bearing
formation penetrated, even those of small yields.
4. Efficient use of personnel. Cable tool rigs are often
operated by a single person.
Disadvantages of Cable tool drilling:

1. Productivity measured in hole produced per day is
low compared to other drilling methods in similar
formations.
2. Hard rock penetration rates very low.
Despite many new drilling developments, cable tool
remains a useful and competitive drilling technique in
some drilling applications.
AUGER DRILLING
Often used for site investigation, environmental and
geotechnical drilling and sampling, and boreholes for
construction purposes, auger drilling can be an efficient
drilling method.

The advantages of auger drilling include low operating
costs, fast penetration rates in suitable formations and
no contamination of samples by fluids. Augers come in
continuous flight, short flight/plate augers and bucket
augers. Continuous flight augers driven by top head
rotary machines (shown above) carry their cuttings to
the surface on helical flights. Continuous flight augers
with hollow stems are often used for sample recovery in
environmental, geotechnical operations.
Short flight/plate augers and bucket augers are used for
large diameter holes. The cuttings are lifted out of the
hole and then removed before drilling continues.

Rotary drilling uses a sharp, rotating drill bit to dig down
through the Earth's crust. Much like a common hand
held drill, the spinning of the drill bit allows for
penetration of even the hardest rock. The idea of using a
rotary drill bit is not new.
Archeological records show that as early as 3000 B.C.,
the Egyptians may have been using a similar technique.
Leonardo Di Vinci, as early as 1500, developed a design
for a rotary drilling mechanism that bears much
resemblance to technology used today. Despite these
precursors, rotary drilling did not rise in use or
popularity until the early 1900's.
Although rotary drilling techniques had been patented
as early as 1833, most of these early attempts at rotary
drilling consisted of little more than a mule, attached to
a drilling device, walking in a circle! It was the success
of the efforts of Captain Anthony Lucas and Patillo
Higgins in drilling their 1901 'Spindletop' well in Texas
that catapulted rotary drilling to the forefront of
petroleum drilling technology.
While the concept for rotary drilling - using a sharp,
spinning drill bit to delve into rock - is quite simple, the
actual mechanics of modern rigs are quite complicated.
In addition, technology advances so rapidly that new
innovations are being introduced constantly. The basic
rotary drilling system consists of four groups of
components. The prime movers, hoisting equipment,
rotating equipment, and circulating equipment all
combine to make rotary drilling possible.

1. Prime Movers
The prime movers in a rotary drilling rig are those
pieces of equipment that provide the power to the entire
rig. Steam engines provided the power to the early drill

rigs. Gas and diesel engines became the norm after
World War II.
Recently, while diesel engines still compose the
majority of power sources on rotary rigs, other types of
engines are also in use; more so in the oil and gas
industry than in the water well sector. Natural gas or
gasoline engines are commonly used, as are natural gas
or gasoline powered reciprocating turbines, which
generate electricity on site. The resulting electricity is
used to power the rig itself. The energy from these
prime movers is used to power the rotary equipment,
the hoisting equipment, and the circulating equipment,
and on large rigs may be used as well to provide
incidental lighting, water, and compression
requirements not associated directly with drilling.
2. Hoisting Equipment
The hoisting equipment on a rotary rig consists of the
tools used to raise and lower whatever other equipment
may go into or come out of the well. The most visible
part of the hoisting equipment is the derrick, the tall
tower-like structure that extends vertically from the well
hole. This structure serves as a support for the cables
(drilling lines) and pulleys (draw works) that serve to
lower or raise the equipment in the well.
For instance, in rotary drilling, the wells are dug with
long strings of pipe (drill pipe) extending from the
surface down to the drill bit. If a drill bit needs to be
changed, either due to wear and tear or a change in the
subsurface rock, the whole string of pipe must be raised
to the surface. In deep wells, the combined weight of the

drill pipe, drill bit, and drill collars (thicker drill pipe
located just above the bit) may be in excess of
thousands of pounds. The hoisting equipment is used to
raise all of this equipment to the surface so that the drill
bit may be replaced, at which point the entire chain of
drill pipe is lowered back into the well.
The height of a rigs derrick can often be a clue as to the
depth of the well being dug. Drill pipe traditionally
comes in 20ft sections, which are joined together as the
well is dug deeper and deeper. This means that even if a
well is 1200 feet deep, the drill string must still be taken
out in 20 foot sections. However, if the derrick is tall
enough, multiple joints of drill pipe may be removed at
once, speeding up the process a great deal.
3. Rotating Equipment
The rotating equipment on a rotary drilling rig consists
of the components that actually serve to rotate the drill
bit, which in turn digs the hole deeper and deeper into
the ground. The rotating equipment consists of a
number of different parts, all of which contribute to
transferring power from the prime mover to the drill bit
itself. The prime mover supplies power to the rotary,
which is the device that turns the drill pipe, which in
turn is attached to the drill bit. A component called the
swivel, which is attached to the hoisting equipment,
carries the entire weight of the drill string, but allows it
to rotate freely.
The drill pipe (which, when joined together, forms the
drill string) consists of 20ft sections of heavy steel pipe.
The pipes are threaded so that they can interlock
together. Drill pipe is manufactured to meet
specifications laid out by the American Petroleum

Institute (API), and others, which allows for a certain
degree of homogeneity for drill pipes across the
industry.
Below the drill pipe are drill collars, which are heavier,
thicker, and stronger than normal drill pipe. The drill
collars help to add weight to the drill string, right above
the bit, to ensure there is enough downward pressure to
allow the bit to drill through hard rock. The number and
nature of the drill collars on any particular rotary rig can
be altered depending on the down hole conditions
experienced while drilling.
Rotary Drill Bits
The drill bit is located at the bottom end of the drill
string, and is responsible for actually making contact
with the subsurface layers, and drilling through them.
The drill bit is responsible for breaking up and
dislodging rock, sediment, and anything else that may
be encountered while drilling. There are dozens of
different drill bit types, each designed for different
subsurface drilling conditions. Different rock layers
experienced during drilling may require the use of
different drill bits to achieve maximum drilling
efficiency. It can be a long process to change bits, due
to the fact that the whole drill string must be removed;
but using the correct drill bit, or replacing a worn bit,
can save a great deal of time during drilling. Drill bits are
chosen given the underground formations expected to
be encountered.
There are four main types of drill bits, each suited for
particular conditions.

1. Blade or Drag Bits forged steel with tungsten
carbide cutting surfaces for drilling
unconsolidated formations. Also called wing bits
or fishtail bits were the first rotary bits. They are
available in 3 way or 6 way designs.
Their cutting action is through a shearing action
on the formation.
2. Steel Tooth Rotary Bits, tricone being the most
common type. Rock or roller cone bits, as they
are often known, were invented in the early
1900’s and have evolved over the years. They
are the most common drill bit type for all drilling
industry sectors. Long tooth roller cone bits are
used for soft formations with short toothed bits
used for hard formations. The cutting action is
through a crushing and chipping action.
Tungsten carbide studs are used in place of

teeth used for particularly abrasive formations
like dolomite, granite, chert, basalt, and quartzite.
3. Polycrystalline Diamond Compact Bits have
polycrystalline diamond inserts attached to the
carbide inserts found in Insert Bits. (primarily
oil&gas industry)

4. Diamond Bits have industrial diamonds
implanted in them, to drill through extremely hard
rock formations. Diamond bits are forty to fifty
times harder than traditional steel bits, and can
thus be used to drill through extremely hard rock
without dulling overly quickly.
Bit types 1&2 are most commonly used in the
water well drilling industry. Bit type 3, in addition
to the oil and gas industry, also has applications in
the directional drilling sector. Bit type 4 is used in
geophysical drilling for coring applications
Regardless of the drill bit selected continuous cutting
removal is essential to rotary drilling. It is an awareness
of this fact that lead to the development of alternative
means to achieve continuous cuttings removal in all
geologic formations. Whatever circulation method
chosen, the purpose of fluid circulation is to keep the
hole clean and the bit turning freely against the bottom.
4. Circulating System
The final component of rotary drilling consists of the
circulating system. There are a number of main
objectives of this system, including cooling and
lubricating the drill bit, removing debris and cuttings,
and coating the walls of the well with a mud type-cake.
The circulating system consists of drilling fluid, which is
circulated down through the well hole throughout the
drilling process. The components of the circulating
system include drilling fluid pumps, compressors,
related plumbing fixtures, and specialty injectors for the
addition of additives to the fluid flow stream.

Basic Rotary Operation
Rotary drilling as opposed to percussion drilling cuts by
rotating a bit at the bottom of the hole. In addition to
rotation, downward pressure must be exerted and
continued as the bit cuts it way through the formation.
Part of the art of rotary drilling is to match the bit type
and pull down pressure with the formation and the use
of drilling fluids to maintain circulation to keep the hole
clear of cuttings and the bit lubricated and cool.
The most common methods of imparting the rotary drive
to the bit are:
1. A rotating table which turns the drill string via a
kelly bar passing through the table and attached to
the top joint of the drill string.

2. Rotating the drill string directly by a hydraulic unit
attached directly to the top of the drill string.

3. Downhole motors (also called down hole turbines)
are widely used in the oil and gas industry, and
impart the rotational force directly at the drill bit.
The earliest down hole bit driving device was the
turbodrill, patented in 1873.

4. Dual rotary rigs which operate upper and lower top
head drives impart rotary cutting motion to both the
drill bit and casing.

Methods of feeding the bit:
Pull down pressure is that force used to impart
downward energy to the drill string.
This force can be created simply by the weight of the
drill string including drill collars and stabilizers attached
immediately behind the bit. If sufficient weight is
attached to the drill string due to the size and depth of
the hole, the string weight by itself may provide
sufficient downward force on the drill bit to insure
continued penetration.
When beginning a new hole and often times during
drilling operations pull-down pressure from the drill rig
is applied. This pull-down force is achieved by a screw,
cable, chain arrangement or by hydraulic motors.
Hydraulically powered pull-down actions are usually

found on more recently manufactured drill rigs, with
screw, cable and chain pull down arrangements more
commonly found on older rotary rigs.
The driller controls the pull-down pressure and thus the
speed of penetration. It must be noted as said in the
beginning of this text that part of the art of rotary drilling
is the matching of pull-down pressure to the formation.
Excessive pull-down pressure can damage drill bits, drill
pipe and the trueness of the borehole. Thus applying
more pull-down pressure is not always the best drilling
practice.
Rotary Fluid Circulation
Rotary drilling requires one of several methods of fluid
circulation to clear cuttings from the borehole. Several
types of rotary drilling methods are best classified by
the type of drilling fluid used, and/or the way in which
the fluid is circulated through the borehole.
Direct circulation- Mud Rotary

In direct circulation rotary drilling fluid (water or water
with additives-mud) is pumped down the drill pipe and
out through the ports or jets in the drill bit. The fluid
then flows up the annular space between the hole and
the drill pipe carrying cuttings in suspension to the
surface.

The drilling fluid, much like the bit, is custom designed
and chosen depending on what type of subsurface
conditions are expected or experienced. The drilling
fluid chosen must have a number of properties to allow
it to accomplish its tasks.
It must be light and thin enough to circulate through the
drill bit, cooling the bit as it drills as well as lubricating
the moving parts. The fluid must be heavy enough to
carry drill cuttings away from the bit and back to the
surface. In addition, the drilling fluid must be thick
enough to coat the borehole with a cake, which serves
to temporarily seal the walls of the well until casing can
be installed.
In direct circulation drilling the circulating system
consists of a starting point, the mud pit, where the
drilling fluid ingredients are stored. Mixing takes place
at the mud pit or in a drum or mixer used for this
purpose. After mixing or the addition of additives the
fluid is forced through pumps up to the swivel and down
all the way through the drill pipe, emerging through the
drill bit itself. From there, the drilling fluid circulates
through the bit, picking up debris and drill cuttings, to
be circulated back up the well, traveling between the
drill string and the walls of the well (also called the
'annular space').
At the surface the fluid is channeled into settling pits or
tanks where most of the cuttings settle out. Clean fluid
is picked up from the opposite end of the settling area.
If portable mud pits are employed, a series of baffles is
used to aid in the settling process. The drilling fluid is
then re-circulated down the hole. The process is
repeated until drilling is completed.

Direct circulation is the most popular of the rotary
drilling methods.
The drilling fluids most often used in direct circulation
rotary drilling contain clay additives (bentonite) or
polymer based additives. A combination of the two
additives is also used. Drilling muds remove cuttings
while cooling and lubricating the drill bit. The drilling
fluid also stabilizes the borehole by the creation of a
wall cake. While these 3 functions, cooling, clearing, &
stabilizing are essential for successful hole completion,
in water well drilling the overuse of additives can make
the removal of the drilling fluid residues more difficult
during well development.
Reverse mud circulation

Reverse circulation drilling was developed to allow for
larger borehole drilling without the limiting factors of
drilling fluid pump capacities. Rotary rigs designed for
reverse circulation have larger capacity mud pumps and
air compressors to allow for increased pressures
needed to insure the removal of cuttings from large
boreholes. These drill rigs are far larger than those
used for domestic purposes. Centrifugal mud pumps

are often used instead of positive displacement because
the cuttings will more easily circulate through a
centrifugal type pump that through a positive
displacement pump.
Reverse circulation rotary drilling is a variant of the mud
Reverse circulation requires a lot of water and sediment
In reverse circulation rotary method, the drilling fluid
To prevent caving of the hole, the fluid level must be
rotary method in which drilling fluid flows from the mud
pit down the borehole outside the drill rods and passes
upward through the bit. Cuttings are carried into the drill
rods and discharged back into the mud pit.
handling, as the boreholes are large in diameter.
Stability of the borehole wall depends on the positive
pressure from the fluid in the borehole annulus. If the
positive pressure is not sufficient, the borehole wall or
parts of it might collapse, trapping the drill string.
can best be described as muddy water rather than
drilling fluid; drilling fluid additives are seldom mixed
with the water to make a viscous fluid. Suspended clay
and silt that recirculates with the fluid are mostly fine
materials picked up from the formations as drilling
proceeds Occasionally, low concentrations of a
polymeric drilling fluid additive are used to reduce
friction, swelling of water-sensitive clays, and water
loss. Since fewer drilling muds are used no wall cake is
created and the stabilization by the borehole fluid is
needed.
kept at ground level at all times, even when drilling is
suspended temporarily, to prevent a loss of hydrostatic
pressure in the borehole. The hydrostatic pressure of
the water column plus the velocity head of the

downward moving water outside the drill pipe are what
support the borehole wall. Erosion of the wall is usually
not a problem because velocity in the annular space in
low.
A considerable quantity of make up water is usually
Often to aid the upward movement of water through the
r a
Reverse mud is a cost effective method for drilling bore
dvantages of Reverse Circulation Mud Rotary
1. The near-well area of the borehole is relatively
hydrogeologic condition.
required and must be immediately available at all times
when drilling in permeable sand and gravel. Under
these conditions, water loss can increase suddenly, and
if this causes the fluid level in the hole to drop
significantly below the ground surface, caving usually
results. Water loss can be addressed by the addition of
clay additives, but this action is only taken as a last
resort.
drill string, air is injected, lifting the contents to the
surface. Another reason to use air is the fact that the
suction pump lift is limited in its capacity to create
enough vacuum to start up the water movement afte
rod change. When air lifting is used to assist in reverse
mud drilling this method becomes similar to the reverse
air rotary drilling method discussed below.
holes of 24” and greater. This method is most
successful in unconsolidated formations.
A
undisturbed and uncontaminated with drilling
additives and the porosity and permeability of the
formation remains close to its original

2.
4. an be set easily as part of the casing
igneous and metamorphic rocks.
illing
Disadvantages include the following:
1. Large water supply is generally needed.
ents are large and
4. ites are inaccessible because of the rig
ally required than for other drilling methods.
Direc g
iscussed in separate section)
fts the cuttings from the
orehole. A large compressor provides air that is piped
Large-diameter holes can be drilled quickly and
economically
3. No casing is required during the drilling operation.
Well screens c
installation.
5. Most geologic formations can be drilled, with the
exception of
6. Little opportunity exists for washouts in the
borehole because of the low velocity of the dr
fluid.
2. Reverse-rotary rigs and compon
expensive.
3. Large mud pits are required.
Some drill s
size.
5. For efficient operation, more personnel are
gener
t air rotary drilling (down the hole hammer drillin
d
In air rotary drilling, air alone li
b
to the swivel hose connected to the top of the Kelly or
drill pipe. The air, forced down the drill pipe, escapes
through small ports at the bottom of the drill bit, thereby
lifting the cuttings and cooling the bit. The cuttings are
blown out the top of the hole and collect at the surface
around the borehole.

Air is low in density. It is also low in viscosity, having a
viscosity approximately 2% that of water. Therefore the
up-hole or bailing velocity must be at least 20 times as
high as the velocity required when using water. Air
drilling has many advantages:

1. Good hole cleaning
2. excellent information on what’s happening down
the hole.
3. immediate indication of water shows with the
opportunity to determine quantity and quality of
water encountered
4. low pollution risk
5. fast penetration
6. high bit life
7. air is readily available.
Air drilling can be done only in semi-consolidated or
consolidated materials. In rigs equipped with both mud
pumps and air-drilling capacity compressors, drillers
may switch to air drilling once the consolidated
formation is reached.
Additives to the air line create stiff foam and add to the
lifting capacity. Drilling with foam has these
advantages:
• low density fluid
• high viscosity gives good cleaning in large
diameter holes
• low air consumption
• low bailing velocity eliminates erosion of the walls
of the hole.
• foam will build wall stability and inhibit swelling of
clays

Roller-type rock bits, similar those designed for drilling
with water-based fluid, can be used when drilling with
air. Tricone rock bits are commonly used. Button bits
are also used successfully. Field test have shown faster
penetration rates and longer bit life when using air and
compared with water-based drilling fluids.
The path for fluid circulation when drilling using direct
rotary air is somewhat the same as for mud rotary
drilling:

Air travels from compressor to the Kelly or swivel down
the drill pipe through nozzles in the bit and exit along
the borehole walls outside the drill pipe.
Drill bit nozzles for air rotary drilling are available in
sizes to suit the down-hole conditions, velocity
requirements, hole depth and compressor capacity.
Disadvantages of Direct Air Rotary Drilling
• cost to purchase sufficient capacity compressor
• cost of maintenance & repair of compressor
Reverse air drilling
This method is most successful when drilling in soft
sedimentary rock and unconsolidated sand and gravel.
This method requires adequate water to be successful.
The air is used to assist in the transport of cuttings up
the drill pipe be creating a partial vacuum which helps to
draw the water and cuttings in suspension. Both reverse
mud and reverse air require larger settling ponds as
there is no recirculation of fluid, the water is drawn from
the producing zones that have been accessed.

A tremie pipe is inserted inside the drill pipe with a
check valve on the bottom of the tremie. Once the
formation has produced water reverse air drilling can be
begun. As drill rods are added, lengths of tremie pipe
are also added until the tremie is submerged more than
20 ft. Air is introduced into the tremie which aerates the
column of water within the drill rod. The now aerated
column is less heavy then the fluid outside the drill pipe.

An air-assisted lift is created up the drill pipe, drawing
cuttings from the borehole through the bit ejecting them
at the exit hose attached to the top of the swivel and into
the holding pond.
Reverse air drilling is seen as an excellent approach for
municipal supply wells. Engineers often specify this
method of drilling be used once the water bearing
formation is reached because there is little change of
contaminants being introduced into the borehole. Also
there is less danger of reducing the permeability of the
near well area because no drilling fluids are used once
reverse air drilling is commenced.
The reverse air method is seldom used in small diameter
wells.
Reverse air drilling Advantages
Rapid removal of cuttings
No plugging of the aquifer with drilling fluids
No use of mud pumps during the air drilling stage
Extended bit life
Easier estimates of formation yield
Loss of circulation zones not a factor
Samples easily obtained
Disadvantages of Reverse Air Drilling
Restricted to semi consolidated and well-consolidated
materials.
High initial and maintenance costs of compressors
Hole must be producing water
Large settling pit needed

Extra work required to add and remove tremie line
during tripping in and tripping out
slower pace of drilling
plugging of string
broken tremie or dislodged check valve
Down the hole air hammer
To drill effectively in hard formations, rotary bits require
very high pull down pressures. These pressures may be
beyond the design capabilities of small to medium drill
rigs. And, as was stated earlier, excessive pull down
pressures may damage the drill string and deflect the
trueness of the hole. If the hard rock formation is near
the surface, even larger rigs have trouble with
penetration as the weight of the drill string is not
relatively great when drilling is beginning.
The down hole hammer is an air activated percussive
drilling bit which operates in the manner of the jack
hammer commonly seen in surface construction.
Constructed from alloy steel with heavy tungsten-
carbide inserts that provide the cutting or chipping
surfaces. These inserts are subject to wear and may be
replaced or reground improve penetration rates.
Corrosion (rust) is the DHH’s greatest enemy. It must be
kept well lubricated at all times. And it should be
opened and inspected after every 100 hours of
continuous operation.

The DHH rotates to insure uniform penetration. During
application the bit face remains in constant contact with
the bottom of the formation. Rather the piston
arrangement behind the bit face impacts the face
repeatedly, fracturing the formation. After each piston
stroke air is exhausted from the bit face, clearing
cuttings and exiting the cuttings out of the borehole on
the outside of the drill pipe. Because of the rapid
cuttings removal, the DHH hits a clean surface with each
stroke, making its operation far more efficient that the
traditional cable tool which strikes through slurry or
previously broken cuttings.
Reverse circulation down hole hammers are also
available. The return air and cuttings are directed up the
center of the hammer when reverse DHH’s are used.

Advantages of Down the Hole Hammer
•fastest hard formation penetration method
•aquifer not tampered with by muds
•extended bit life
•cold weather non factor
•easy yield estimates
•no mud pumps
Disadvantages of Down the Hole Hammer
•initial costs of air compressors
•maintenance and repair costs of compressor and DHH
Jet Drilling
Drilling in unconsolidated formation with high water
availability allows jet drilling to be a viable drilling
method. Often employed in drilling shallow irrigation
wells, jet drilling is achieved by water circulation down
through the rods washing cuttings from in front of the
bit. The cutting flow up the annular space and in a
settling pit so that the water can be recirculated.
Jetting in semi consolidated formations may be assisted
by using a hammering technique to “chop” through
hard bands. This technique is a combination of jetting
and percussion. A fish-tail type rotary bit may be used
and the pipe rotated to “cut the hole. All hydraulic
(water based) drilling requires that the hole be kept full
off water until it is cased.

A variation of the jetting method is the wash down
method where the wash pipe is inserted within the well
screen in an arrangement whereby water under pressure
is pumped through the wash pipe at the bottom of the
screen. The jetting action allows the screen to sink to
the desired location without any predrilling.

Wells have been jetted to depths of 1000 feet and drillers
have used jetting or washing techniques to place
screens in completed boreholes to insure placement at
the precise level desired.
END OF TEXT
Take Test

Drilling methods by RAJESH GUPTA

More Related Content

What's hot (17)

Similar to Drilling methods by RAJESH GUPTA (20)

Recently uploaded (20)

Drilling methods by RAJESH GUPTA