![The Coriant® Smart Router Series
The Smart Router Series offers versatile and scalable solutions for service provider access and aggregation from small hub sites to
controller and gateway sites. Smart Routers serve fixed and mobile convergence and cloud computing networking needs and are
designed to meet the ever-growing requirements of data hungry mobile and enterprise users. The entire Smart Router Series shares
a common Network Operating System for consistent support of an extensive Ethernet and IP/MPLS feature set, including broad QoS,
OAM, and network resiliency options. Advanced traffic management features include hierarchical policing and shaping support with
Strict Priority and WFQ Scheduling. Simultaneous support for multiservice applications in access and aggregation networks protects
earlier network investments. The Smart Router Series is supported by the 8000 INM and Coriant Transcend™ SDN Packet Controller.
TECHNICAL SPECIFICATIONS
Physical Dimensions
• 5RU high
• 300 mm deep
• 19-inch rack mounting
• 8625-O Smart Router optical layer
extension: 1RU 8-slot FOADM
passive shelf
Power and Cooling
• -48 Vdc, redundant power supply
• Two user changeable power modules
with optional protection
• Maximum power consumption with two
Line Unit 1 cards: 650 W
• Maximum power consumption
supported by power input modules:
1300 W (for future Line Units)
• Forced cooling with two fan modules
• Airflow: Side to side or side to back (by
adjusting airflow panel)
Forwarding Plane
• IPv4 and IPv6 routing
• Multicast
• MPLS switching (LSR and LER)
• Ethernet MAC switching
• Optical Layer: 1, 2, 4, and 8 channel
filters
Functionality
• IP VPN (RFC 4364)
• IP VPN multicast
• VPLS and H-VPLS
• Integrated routing and bridging
• 6vPE support
• Ethernet/VLAN pseudowires
• Single and multi-segment pseudowires
• 802.1ad QinQ
• Seamless MPLS
• Two Way Active Measurement Protocol
(TWAMP)
• Y.1731 frame loss, frame delay, and
frame delay variation measurement
• IEEE 802.1ag Ethernet OAM loopback,
continuity check, ping, and link trace
• BFD (Static, OSPF, ISIS, RSVP-TE)
Forwarding Capacity
• 400 Gbps full duplex forwarding capacity
Chassis Configuration
• Two Power Input Modules
• Two slots for Line Units
• Two Fan Modules
Line Units
• Line Unit 1: 1 x 100GBASE-R (CFP2) + 24
x 10GBASE-R with two operating modes:
• 1 x 100GBASE-R (CFP2) + 14 x
10GBASE-R
• 24 x 10GBASE-R
Resiliency and Load Balancing
• 1+1 Control plane protection
• Nonstop forwarding with control plane
redundancy and graceful restart
• Power input protection
• Ethernet Link Protection
• Ethernet Link Aggregation
• 1:1 RSVP-TE LSP protection
• Fast Reroute (FRR)
• Ethernet pseudowire redundancy
• VRRP
• IP load balancing (Equal Cost Multipath
[ECMP])
• BGP multipath for load balancing
• IPv4 and IP VPN load balancing to
RSVP-TE tunnels
Common Interfaces
• Station Clock Input/Output (SCI/SCO)
• Pulse-per-Second (PPS) clock input and
output
• Time-of-Day (ToD) input
• External Alarms
• Console
Security
• L3/L4 Access Control Lists
• Denial of service protection
• Radius and TACACS+ authentication
and accounting
• SSH-2 for FTP and Telnet
• MD5, SHA-1 authentication
Synchronization
• ITU-T [G.8262]
• Station Clock Input and Output ports
• Pulse-per-Second (PPS) input and
output
• Time-of-Day input
• Synchronous Ethernet
• SSM over Ethernet [G.8264]
• IEEE 1588v2 Boundary Clock for phase
sync
• SyncE assist
• Support for the Integrated GPS (GNSS)
SFP receiver
Routing and MPLS Label Distribution
Protocols
• OSPF-TE, ISIS-TE, BGP, and MP-BGP
• LDP, RSVP-TE
• PIM-SM and PIM-SSM
Traffic Management
• DiffServ support for up to 7 traffic
classes
• DiffServ aware MPLS Traffic
Engineering (DS-TE)
• IEEE 802.1P/Q mapping to IP or MPLS
• Policing: port, VLAN, hierarchical
• Shaping: port, VLAN, hierarchical
• RED/WRED queue management
• Strict Priority and WFQ scheduling
• Access Control Lists (ACL)
3 8625 Smart Router](https://image.slidesharecdn.com/ds8625smartrouter74c01301-171227075329/85/Ds-8625-smart_router_74_c0130-1-3-320.jpg)
Ds 8625 smart_router_74_c0130 (1)
- 1. 8625 Smart Router High Speed IP/MPLS Router for 5G Networks The Coriant® 8625 Smart Router serves as a step forward in the carrier drive towards 5G and high speed fixed mobile convergence (FMC) networks. In addition to a nonblocking 400 GbE capacity spread between redundant line cards, the 8625 Smart Router leverages the Coriant® Pluggable Optical Layer to deliver terabit speed in access and aggregation networks. To effectively support advanced LTE-A and 5G air interface technologies, the 8625 Smart Router is equipped with Coriant’s industry- leading range of network synchronization options that can be further optimized with low latency optical transport. The compact 300 mm deep chassis and power efficient design are ideally suited for installations in metro and access networks. Support from both the Coriant® 8000 Intelligent Network Manager (INM) and Coriant Transcend™ SDN Packet Controller provides a broad array of operational efficiencies and programmable network automation. The 8625 Smart Router has been designed with the future in mind for WAN service providers. ENABLING FLEXIBLE LTE NETWORK ARCHITECTURES Offering ideal capabilities to implement flexible LTE and 5G networks, the 8625 Smart Router platform provides IP routing and Ethernet switching to support the X2 interface between eNodeBs and S1 and S1-Flex interfaces between eNodeBs and LTE network core elements. The 8625 Smart Router supports both fixed and mobile transport, so mobile operators can extend their service offering to include fixed network services. The IEEE 1588v2 phase synchronization capabilities of the 8625 Smart Router are designed to meet the strict tolerance of LTE-TDD and LTE-A networks as well as the even more stringent synchronization targets for 5G. The integrated features of the 8625 Smart Router enable simple migration from existing frequency synchronization to phase synchronization. SUPPORTING ALL-IP AND FIXED NETWORKS An optimal solution for mobile and fixed networks that deploy microwave, wired Ethernet, or dark fiber as the underlying transport media, the 8625 Smart Router contains IP routing as well as MPLS and Ethernet switching tables that provide the flexibility needed to serve evolving network architectures and applications. The 8625 Smart Router supports a mix of IP and Ethernet services, such as IP VPNs, VPLS and Ethernet pseudowires, significant buffering capacity for bursty data applications, and advanced traffic management features with hierarchical QoS support for flexible end- user service definition. IP-Multicast support is available for applications such as eMBMS and IPTV broadcast delivery. DELIVERING CONVERGED IP-OPTICAL INTEGRATION The 8625 Smart Router includes an 8625-O Smart Router variant, which is an expansion option for combined IP-Optical transport with the Pluggable Optical Layer. The converged solution of the 8625-O Smart Router addresses the demands of continuously increasing bandwidth while minimizing OpEx and CapEx. The solution includes colored interfaces on the Smart Routers coupled with the Pluggable Optical BENEFITS OF THE CORIANT® 8625 SMART ROUTER ■■ Leverages purpose-built architecture for FMC and 5G networks ■■ Optimizes 10G/1G aggregation with 100G connectivity ■■ Provides option to integrate FOADM optical layer for expanded capacity ■■ Delivers high-density, compact form factor for metro and aggregation networks ■■ Offers a comprehensive range of synchronization options ■■ Enables SDN capabilities for network automation and optimization DATASHEET
- 2. Layer as a high-capacity transport underlay. This architecture leverages the flexibility of Layer 3 with cost-efficient optical transport to optimize routing capacity by off-loading pass-through transit traffic to 10/100G optical transport circuits in a low cost and low latency network design. Integrated IP-Optical transport delivers a dramatic capacity increase for routing sites. Combined IP-Optical transport enlists the advantages of the Coriant Transcend™ SDN Solution, a powerful toolkit that enables optimized multi-layer service and resource management. The Coriant IP-Optical transport solution represents the realization of a future-proof network architecture to meet the challenges in the transition to 5G by minimizing cost per bit, increasing bandwidth, and lowering latency. OFFERING A RANGE OF SYNCHRONIZATION OPTIONS The 8625 Smart Router enables efficient and reliable synchronization for LTE-A and 5G. The 8625 Smart Router supports a wide range of synchronization features including Synchronous Ethernet, Synchronization Status Message (SSM) over Ethernet, and IEEE 1588v2 Boundary Clock required for LTE-TDD, LTE-A, and future 5G mobile networks. Phase synchronization master clock can be supported using the innovative Coriant® Integrated GPS (SNSS) SFP receiver as a timing source on the 8625 Smart Router. All synchronization features are software configurable without any required hardware changes. This highly sophisticated synchronization implementation provides a cost-efficient, flexible, and robust rollout of packet-based synchronization. REDUCING OPERATING EXPENSES WITH INTELLIGENT NETWORK MANAGEMENT Fully managed by the 8000 INM, the 8625 Smart Router seamlessly integrates into any existing Smart Router network, network expansion, or greenfield deployment. The 8000 INM supports the operator throughout the network lifecycle from planning and deployment phases all the way to optimization and maintenance by automating many routine network management tasks to reduce operational expenses. IMPLEMENTING AN OPEN, PROGRAMMABLE, AUTOMATED SDN SOLUTION The Coriant Transcend™ SDN Packet Controller fully supports the 8625 Smart Router. The Packet Controller is an integral component of the overall Coriant Transcend™ SDN Solution suite, a modular SDN software suite that combines the benefits of open, programmable, and automated multi-layer SDN architecture and a proven portfolio of IP/MPLS edge routing and packet optical transport solutions to enable dynamic, end-to-end network control and optimization. PROVIDING HIGH INTERFACE DENSITY AND COMPACT FORM FACTOR The 8625 Smart Router is designed to offer high speed packet aggregation capabilities in a compact 5RU design with low power consumption and full redundancy of forwarding, control and management plane, synchronization, power, and fan modules. The 8625 Smart Router supports a flexible Line Unit design. The first released Line Unit (LU1) has multiple interface configuration options with a mix of 100 Gbps, 10 Gbps, and 1 Gbps Ethernet support. The 8625 Smart Router supports two Line Units providing 400 Gbps total bidirectional throughput with LU1. Each Line Unit includes a dedicated control processor for resiliency and stateful recovery in the case of a card failure. Hot swap deployment enables consistent throughput without service interruption during node upgrades. TNMS Intelligent Network Management and Control 8000 INM Transcend SDN 8625 Smart Router IP-Optical 8625-O Smart Router Packet Routing and WDM TransportPacket Routing FOADM: Pluggable Optical Layer Solution Figure 1: 8625 Smart Router Variants with Combined Optical Transport Option 2 8625 Smart Router
- 3. The Coriant® Smart Router Series The Smart Router Series offers versatile and scalable solutions for service provider access and aggregation from small hub sites to controller and gateway sites. Smart Routers serve fixed and mobile convergence and cloud computing networking needs and are designed to meet the ever-growing requirements of data hungry mobile and enterprise users. The entire Smart Router Series shares a common Network Operating System for consistent support of an extensive Ethernet and IP/MPLS feature set, including broad QoS, OAM, and network resiliency options. Advanced traffic management features include hierarchical policing and shaping support with Strict Priority and WFQ Scheduling. Simultaneous support for multiservice applications in access and aggregation networks protects earlier network investments. The Smart Router Series is supported by the 8000 INM and Coriant Transcend™ SDN Packet Controller. TECHNICAL SPECIFICATIONS Physical Dimensions • 5RU high • 300 mm deep • 19-inch rack mounting • 8625-O Smart Router optical layer extension: 1RU 8-slot FOADM passive shelf Power and Cooling • -48 Vdc, redundant power supply • Two user changeable power modules with optional protection • Maximum power consumption with two Line Unit 1 cards: 650 W • Maximum power consumption supported by power input modules: 1300 W (for future Line Units) • Forced cooling with two fan modules • Airflow: Side to side or side to back (by adjusting airflow panel) Forwarding Plane • IPv4 and IPv6 routing • Multicast • MPLS switching (LSR and LER) • Ethernet MAC switching • Optical Layer: 1, 2, 4, and 8 channel filters Functionality • IP VPN (RFC 4364) • IP VPN multicast • VPLS and H-VPLS • Integrated routing and bridging • 6vPE support • Ethernet/VLAN pseudowires • Single and multi-segment pseudowires • 802.1ad QinQ • Seamless MPLS • Two Way Active Measurement Protocol (TWAMP) • Y.1731 frame loss, frame delay, and frame delay variation measurement • IEEE 802.1ag Ethernet OAM loopback, continuity check, ping, and link trace • BFD (Static, OSPF, ISIS, RSVP-TE) Forwarding Capacity • 400 Gbps full duplex forwarding capacity Chassis Configuration • Two Power Input Modules • Two slots for Line Units • Two Fan Modules Line Units • Line Unit 1: 1 x 100GBASE-R (CFP2) + 24 x 10GBASE-R with two operating modes: • 1 x 100GBASE-R (CFP2) + 14 x 10GBASE-R • 24 x 10GBASE-R Resiliency and Load Balancing • 1+1 Control plane protection • Nonstop forwarding with control plane redundancy and graceful restart • Power input protection • Ethernet Link Protection • Ethernet Link Aggregation • 1:1 RSVP-TE LSP protection • Fast Reroute (FRR) • Ethernet pseudowire redundancy • VRRP • IP load balancing (Equal Cost Multipath [ECMP]) • BGP multipath for load balancing • IPv4 and IP VPN load balancing to RSVP-TE tunnels Common Interfaces • Station Clock Input/Output (SCI/SCO) • Pulse-per-Second (PPS) clock input and output • Time-of-Day (ToD) input • External Alarms • Console Security • L3/L4 Access Control Lists • Denial of service protection • Radius and TACACS+ authentication and accounting • SSH-2 for FTP and Telnet • MD5, SHA-1 authentication Synchronization • ITU-T [G.8262] • Station Clock Input and Output ports • Pulse-per-Second (PPS) input and output • Time-of-Day input • Synchronous Ethernet • SSM over Ethernet [G.8264] • IEEE 1588v2 Boundary Clock for phase sync • SyncE assist • Support for the Integrated GPS (GNSS) SFP receiver Routing and MPLS Label Distribution Protocols • OSPF-TE, ISIS-TE, BGP, and MP-BGP • LDP, RSVP-TE • PIM-SM and PIM-SSM Traffic Management • DiffServ support for up to 7 traffic classes • DiffServ aware MPLS Traffic Engineering (DS-TE) • IEEE 802.1P/Q mapping to IP or MPLS • Policing: port, VLAN, hierarchical • Shaping: port, VLAN, hierarchical • RED/WRED queue management • Strict Priority and WFQ scheduling • Access Control Lists (ACL) 3 8625 Smart Router
- 4. These trademarks are owned by Coriant or its affiliates: Coriant®, Coriant CloudWave™, Coriant Dynamic Optical Cloud™, Coriant Groove™, Coriant Transcend™, mTera® , Nano™, and Pico™. Other trademarks are the property of their respective owners. Statements herein may contain projections regarding future products, features, or technology and resulting commercial or technical benefits, which may or may not occur. This publication does not constitute legal obligation to deliver any material, code, or functionality. This document does not modify or supplement any product specifications or warranties. Copyright © 2017 Coriant. All Rights Reserved. 74C.0130 Rev. C 07/17 www.coriant.com Management • CLI with SSH2, FTP with SSH2 • SNMPv1 and SNMPv2 monitoring • Coriant® 8000 Intelligent Network Manager (INM) • Coriant Transcend™ SDN Packet Controller • Radius and TACACS+ authentication and accounting Environmental Conditions • Operating temperature: -5°C to +55°C, when airflow is from side to side • Operating temperature: -5°C to +45°C, when airflow is from side to back