DTTB_Case_Study_Australia_2015

AUSTRALIA
T e l e c o m m u n i c a t i o n D e v e l o p m e n t S e c t o r
Printed in Switzerland
Geneva, 2015
International Telecommunication Union
Telecommunication Development Bureau
Place des Nations
CH-1211 Geneva 20
Switzerland
www.itu.int
IMPLEMENTATIONOFDIGITALTERRESTRIALTELEVISIONBROADCASTINGCASESTUDY—AUSTRALIA
Report
Implementation of Digital
TERRESTRIAL TELEVISION
BROADCASTING: CASE STUDY —
A U S T R A L I A
9 7 8 9 2 6 1 1 5 8 6 1 3
ISBN 978-92-61-15861-3

Implementation of digital terrestrial
television broadcasting:
Case study – Australia

This case study has been developed by Mr Andrew King, with revision from Mr Roger Bunch, vice-chairman
of ITU-R Study Group 6. ITU would like to thank the Department of Communications, Government of
Australia, and the Australian Communications and Media Authority (ACMA) for their support.
Please consider the environment before printing this report.
 ITU 2015
All rights reserved. No part of this publication may be reproduced, by any means whatsoever, without the
prior written permission of ITU.

Implementation of digital terrestrial television broadcasting: Case study – Australia
iii
Executive summary
Introduction
Australia’s transition from analogue to Digital Terrestrial Television Broadcasting (DTTB) has been a project
that spans a period since 1993. That may be thought of as a very slow transition, however that time span
commences before DTTB was a reality and includes the involvement of Australian experts contributing to
the development work in the ITU-R for a period of approximately four to five years, benefitting many
Administrations that were to follow on the same transitional path. In the 1990s, the concept of a "digital
dividend" had not been born. This concept developed during the period of simulcast of analogue and digital
services, which resulted in an additional stage to the project to restack the DTTB services and release
spectrum in the UHF band for other services. In Australia’s case, this heightened the resources needed at
the time of analogue switch off and added one year to the overall project.
The actual simulcast on-air duration of analogue and digital services during the transition varied by licence
area. The shortest transition time was achieved in the rural area of Mildura which had a period of six year
simulcasting, whereas the major metropolitan licence areas of Sydney and Melbourne had the longest
simulcast times of 13 years.
Broadcast networks
Australia’s population of 23.6 million people live mainly around the coastal areas and are able to watch
free-to-air terrestrial broadcast television mostly provided by five broadcast networks. There are two
national broadcasters, owned by the government whose licences cover the whole country, but their
services tend to be organised to cover a state or even a state capital city. Commercial broadcasters are
licenced to broadcast to a specific licence area, with only three licences available in any one area, except
for some overlap areas between the cities and regional areas where six licences have been issued. Media
ownership laws limit the population coverage for the owner of a commercial television network, so the
commercial broadcast companies have formed into three capital city broadcast networks and six regional
broadcast networks with programme affiliation agreements which results in most programming being
available Australia-wide on a network of licenced stations but with different ownership as shown in the
map below. The capital city broadcasters typically broadcast in Brisbane, Sydney, Melbourne, Adelaide and
Perth (which comprise 66.71 per cent of the population of Australia). In the capital cities there is one
community television service.
During the transition, each network had one 7 MHz channel for their analogue service and has one 7 MHz
channel for their digital service. Each licence area is primarily served from a main transmitter which is fed
via microwave or fibre links from the broadcast station. In areas where terrain would degrade reception
from this transmitter, a broadcast site is established to receive the signal from the main transmitter and
re-broadcast it on another channel. These sites are called translator sites, translating the main channel into
the local in-fill channel.
The digital services are operated independently by each broadcaster, there is no common multiplex
provider for digital broadcast services in Australia.

iv
A phased approach
The transition from analogue to DTTB is considered in five stages:
 Stage 1 – Preparation and Planning
 Stage 2 – Implementation
 Stage 3 – Digital Enhancement
 Stage 4 – Analogue Switch Off, and
 Stage 5 – Digital Restack.
Stage 1 – Preparation and planning
This stage involved Australian experts contributing to the development work in the ITU-R Study Group 11
and in particular, Task Group 11/3 where Australia was instrumental in establishing the objective of
preparing a common set of digital terrestrial television broadcasting (DTTB) standards.
Domestically, investigations were undertaken by a Specialist Group drawn from government and industry
and led by the broadcasting regulator at the time, the Australian Broadcasting Authority. These
investigations culminated in 1997 in broadcaster led testing of the two viable transmission systems
available at the time, the North American ATSC system based on 8VSB modulation and the European DVB-T
system with COFDM modulation. Exhaustive testing and evaluation led to the decision to recommend the
DVB-T system for Australia.
Having the technical foundations in place, government policy was announced supporting legislation passed
in 1998. This formed the basis for the regulator to commence planning the simulcast of analogue and digital
services and undertake appropriate licencing. At the same time government and industry met to develop
technical standards for the system.

v
Stage 2 – Implementation
This stage commenced approximately a year prior to the first DTTB transmissions as broadcasters sourced
digital video encoders, multiplexers and other headend equipment and purchased and installed digital
transmitters. The first on-air tests were undertaken in August 2000, followed in September 2000 by a mobile
tests co-incident with the staging of the Sydney 2000 Olympic Games. DTTB formally commenced in Sydney,
Melbourne, Brisbane, Adelaide and Perth on 1 January, 2001. Initially services were planned to have an
eight year simulcast with digital, regional areas were scheduled three years later.
At commencement, limitations were placed on what broadcasters could do in their digital transmissions,
limiting the flexibility and innovation available in a digital system. At the time, digital set-top receivers were
considered expensive and widescreen displays were still based on analogue technologies, but there was
considerable product development undertaken in display technologies commencing with cathode ray tubes
(CRT) whose size was ultimately limited by the strength of glass in the screen, rear projection systems which
enabled larger displays but suffered from optical alignment issues to plasma displays which were digital in
nature and of high quality and finally to liquid crystal displays (LCD) which have ultimately been embraced
by consumers and accelerated digital take up in homes.
This was a period of approximately six years which allowed broadcasters to test various aspects of the digital
system and for engineers to focus on refinement of the transmission network. Digital take up by consumers
provided a better statistical base for viewer complaints so reception issues could be investigated. These
generally fell into two categories; complaints related to reception of single frequency networks (SFNs) and
issues regarding variable reception which allowed better understanding of the "cliff effect" of digital signals
related to terrain and foliage clutter in varying weather conditions.
Refinements were made to the service information inherent in digital broadcasts and the development of
electronic programme guide information. Whereas many aspects of free-to-air television are highly
regulated by government, Australia has a free unregulated market for supply of television receivers. Many
manufacturers saw opportunities in Australia so a wide variety of receivers were available. The software
design of each receiver had its own idiosyncrasies which often led to viewer complaints that were resolved
by attention to fine detail in service information or close collaboration with manufacturer’s design teams.
After the initial rollout of transmitters at existing broadcasting sites, there was a period of stability in the
broadcast networks.
Stage 3 – Digital enhancement
In 2006, despite the take up actually accelerating due to the changes in display technology and lowering
consumer prices, public debate over the take up of digital, pressure from telecommunication interests to
secure spectrum from the "digital dividend" and the election of a new government triggered a review of
the system with the aim of forcing the switch off of analogue broadcasts and release of broadcasting
spectrum for other services.
Reliable, quality digital coverage is vital to broadcasters as that is their only means of accessing viewers.
With the pending closure of the analogue service in sight, broadcasters commenced an intensive review of
digital coverage. In Stage 2, "same coverage" was essentially achieved by installing digital transmitters at
the existing analogue broadcasting sites and operating at powers 6 dB lower than analogue. However,
garnering the experience gained in Stage 2 from investigating viewer reception complaints and undertaking
extensive field surveys, each licence area was reviewed to investigate methods of cost-effectively
enhancing coverage in areas where the digital service was proving to not be completely reliable.
This review necessitated the establishment of 34 new digital sites in the major metropolitan areas of
Sydney, Melbourne, Brisbane, Adelaide and Perth and 85 new digital sites in regional licence areas. As part
of this review, many smaller sites in metropolitan and regional areas that were outside of the broadcaster’s
control were taken over by broadcasters.

vi
The government was also concerned that there would be some viewers that may not receive adequate
digital services and to address this the government worked with the national broadcasters and remote area
commercial broadcasters to provide a digital satellite service which would provide services to remote
viewers and also provide a safety net for viewers in metropolitan and regional areas where viewers were
not able to access terrestrial digital services.
The investigation and planning stage for these sites took approximately three years to complete and
installation the following three to four years. This stage had to be completed prior to analogue switch off
so that viewers did not lose services during the changeover.
When these additional gap filling sites were established, the main digital and analogue services were still in
operation, so special attention was given to planning spectrum for these sites as the broadcasting spectrum
was already heavily congested. Some smaller analogue only transmitter sites had to be turned off and
turned on in digital mode on the same day as spectrum would not otherwise have been available. Other
sites were integrated into single frequency networks with existing digital sites to make better use of
available spectrum.
Stage 4 – Analogue switch off
Switching off a service is a relatively simple task. However, planning to ensure that the viewing public will
not be impacted by the switch off is complex. The government established a Task Force to plan the switch
off of analogue services. This group had to liaise widely with broadcasters and other industry segments to
ensure that all facilities were in place in preparation for the switch off. Government and broadcasters had
a shared outcome, broadcasters wanted to know that they would not suffer a loss of audience on switch
off, for government this audience represents the voting public so they wanted to ensure they were not
affected by the switch.
Hence a programme of household surveys was established to gauge the number of homes that had
converted to digital and identify issues on acceptability of the digital service or reasons impeding the public
from converting. Lower socio-economic groups in the community were identified for assistance in
converting to digital, generally by being eligible for a free set-top box and installation.
As not all self-help translator sites were taken over and converted to digital by commercial broadcasters,
the government also ran a programme to subsidise the installation of satellite reception equipment
(dish and set-top-box), for viewers in areas where their local translator was not being converted to digital.
Switch off was planned to occur by licence area as this followed dependant signal paths where often
switching off the main transmitter would mute the following translators and re-transmitters. Public
information campaigns were devised to inform the public of the switchover date and assistance campaigns.
Actual switch off dates and times were agreed between broadcasters and government to be a mutually
acceptable time when no high rating or especially important programming was scheduled for broadcast.
The campaigns and plans were tested by first switching off the smaller regional licence area of Mildura. Post
switch off surveys were conducted to provide feedback and modify the campaigns and plans. The remainder
of the licence areas were switched off sequentially in a plan that allowed for timely mobilisation of
resources for the assistance campaigns.
Stage 5 – Digital restack
Government had made a policy decision to auction the 694-820 MHz spectrum band in 2012 as a "Digital
Dividend" before the switch off was completed. This required the planning of the restack of digital services
co-incident with planning the switch off. Planning this stage involved examination by broadcasters of the
practicality of re-tuning their digital transmitters. Digital / digital simulcasts were undertaken in areas of
high populations of multi dwelling units (MDUs) where it was considered likely there were channelised
headends which needed modification by antenna installers, hence viewers were not able to retune their
receivers at a nominated time.

vii
Resourcing an intensive restack was a key issue. The programme for restacking was tendered by the
government to a Program Implementation Manager who liaised with broadcasters and transmitter facility
operators and arranged resources. The restack programme meant nearly every transmit site needed a
modification to the filter / combiner which combines the transmitters into one feed for the antenna. This
is a specialised area where overseas resources were needed to augment Australian manufacturing capacity.
Technical restack teams were created from broadcaster, transmitter manufacturer and installation staff.
The relatively short timeframe for restack and the number of sites involved meant local and overseas
personnel were needed for the program.
In a similar manner to switch off, public information campaigns were undertaken. Actual restack days were
placed into "windows" agreed by broadcasters to avoid high rating programming. Considerable spectrum
planning was undertaken to ensure that a restack of services in a licence area did not cause interference
into an adjacent licence area.
Australia has auctioned the "digital dividend" spectrum in lots based on the APT 700 MHz plan. However,
to protect broadcasting services, the out-of-band emissions from the planned mobile services above
700 MHz, Australia has stipulated 6 dB tighter limits than the APT, but will relax this limit to the APT
specification of –34 dBm/MHz only in areas where the three highest television channels 49, 50 & 51 are not
used.
Key learnings
The key success factors of the conversion of Australian broadcasting to digital have been:
 maintenance of a close working relationship between government and broadcasters;
 open communication with the public, to seek feedback on reception conditions and communicate
changes;
 development of standards to modify a ‘toolkit’ of international standards to incorporate local
requirements;
 planning each stage is key, every detail must be examined.
The key lessons learned:
 set regular reviews to examine if policy and technical goals are being achieved;
 survey households from an earlier stage to judge the success of the conversion;
 setting target dates provides a firm goal for all parties to work towards;
 effort is needed to educate the public from ‘analogue’ to ‘digital’ thinking; influencing perceptions
of degraded reception (‘digital cliff’), channels to services and new features;
 every householder’s reception conditions are different, a variety of causes and solutions to
reception issues need to be developed;
 with respect to analogue switch off and the digital restack:
– review digital coverage before considering the size of a digital dividend;
– use the restack to remove legacy broadcast planning issues;
– a single retune day can be successful only after considerable planning.

viii
Conclusions
What started out as an engineering-led concept to deliver to the viewing public higher quality broadcast
pictures and sound has opened up challenges and opportunities that are inherent with any disruptive
technological change. The project has touched in some way every Australian; whether it be their need to
purchase a new television receiver to continue to watch the shows they like or change the time they watch
those shows as digital recorders have made "time shifting" a reality, businesses that have been rejuvenated
implementing the changes, competitive media outlets who have had to change their business models or
even to minority groups such as the hearing impaired who now enjoy a wider variety of captioned
programmes. The impact has been greatest on two groups; broadcasters and government. The issues for
government have been immense to chart a course through the political, social, economic and technological
issues.
For broadcasters, every part of their business operations have changed. Changes have been required from
camera to transmitter and every piece of equipment along the system chain. Delivering better pictures and
sound to the viewer only highlighted the limitations in equipment used for contributing programmes to the
broadcaster. More services have been added by each broadcaster, the presentation facilities for each
service have changed from a local operation to aggregated national operations. The digitisation of studios
has led to new workflows allowing more rapid response to breaking news stories, shortened production
times and added flexibility as to what to put to air.
Has the transition been a success? Undoubtedly the answer is in the affirmative. Analogue has been
switched off, very few, if any viewers were lost in the conversion to digital television. Whilst the timeframe
might be considered long by some commentators, it must be remembered that Australia was one of the
"early adopters" of digital television and conversion rates only increased when consumer technology
features and price points matched the public’s expectations of the new system. Others have benefitted
from the process as well though the work undertaken jointly by broadcaster’s and the regulator’s
engineering work refining the platform and offering that as contributory work to the ITU-R for other
Administrations to build their systems on the work done in Australia.

ix
Table of contents
Page
Part 1  Country Profile ............................................................................................................... 1
1.1 Population and Geographic Overview.............................................................................. 1
1.2 System Of Government .................................................................................................... 1
1.3 Australian Broadcast Market............................................................................................ 1
1.3.1 Introduction ........................................................................................................... 1
1.3.2 Terrestrial Broadcasting......................................................................................... 2
1.3.3 Technical Broadcast Overview............................................................................... 5
1.4 Key Stakeholder Groups ................................................................................................... 6
1.5 Policy, Legal and Regulatory Frameworks ........................................................................ 7
1.5.1 Government and Regulatory Authorities............................................................... 7
1.5.2 Industry Co-regulation ........................................................................................... 8
1.5.3 Legislation .............................................................................................................. 10
1.6 Planning and Licencing...................................................................................................... 11
1.6.1 Analogue Planning ................................................................................................. 11
1.6.2 Digital Terrestrial Television Broadcasting (DTTB) planning.................................. 11
1.6.3 Licensing................................................................................................................. 13
1.6.4 Television Spectrum............................................................................................... 13
1.6.5 Standards ............................................................................................................... 15
1.7 Roadmap Overview........................................................................................................... 15
1.7.1 Stage 1 – Preparation and Planning....................................................................... 15
1.7.2 Stage 2 – Implementation...................................................................................... 16
1.7.3 Stage 3 – Digital Enhancement .............................................................................. 16
1.7.4 Stage 4 – Analogue Switch Off............................................................................... 16
1.7.5 Stage 5 – Digital Restack ........................................................................................ 16
Part 2  Preparation and Planning................................................................................................ 17
2.1 System Selection............................................................................................................... 17
2.1.1 Origins for considering Digital................................................................................ 17
2.1.2 ABA Specialist Group on Digital Terrestrial Broadcasting...................................... 17
2.1.3 Broadcaster-led Specialist Group........................................................................... 18
2.1.4 Selection Panel....................................................................................................... 19
2.1.5 Planning Implications............................................................................................. 20
2.2 The Government's Decisions ............................................................................................ 22
2.3 Standards Development ................................................................................................... 23
2.3.1 Transmission .......................................................................................................... 23
2.3.2 Development of a DTTB Reference Transport Stream........................................... 24
2.3.3 Reception............................................................................................................... 25

x
Page
Part 3  Implementation.............................................................................................................. 26
3.1 Introduction...................................................................................................................... 26
3.2 Digital Services.................................................................................................................. 26
3.3 Transmitter Rollout........................................................................................................... 26
3.3.1 Interference Management Scheme....................................................................... 27
3.3.2 Development of DVB Service Information............................................................. 29
3.4 Consumer Take-Up ........................................................................................................... 30
3.5 Viewer Complaints............................................................................................................ 31
3.6 Receivers........................................................................................................................... 34
3.7 Government Reviews........................................................................................................ 34
3.7.1 Digital Australia...................................................................................................... 35
Part 4  Digital Enhancement....................................................................................................... 36
4.1 Introduction...................................................................................................................... 36
4.2 Review of Underserved Areas........................................................................................... 36
4.3 Black Spot and Satellite Solutions..................................................................................... 38
Part 5  Analogue Switch Off ....................................................................................................... 40
5.1 Introduction...................................................................................................................... 40
5.2 Digital Switchover Taskforce............................................................................................. 40
5.2.1 Industry Advisory Group and Working Groups...................................................... 40
5.2.2 Government Assistance Schemes.......................................................................... 40
5.2.3 Digital Tracker ........................................................................................................ 42
5.2.4 Publicity and Labelling Scheme.............................................................................. 42
5.3 Digital Switchover Timetable............................................................................................ 43
5.4 Digital Broadcasting Network ........................................................................................... 45
Part 6  Digital Restack................................................................................................................ 46
6.1 Introduction...................................................................................................................... 46
6.2 Restack and Reallocation Processes ................................................................................. 46
6.2.1 Clearing the Digital Dividend.................................................................................. 46
6.2.2 Auctioning Digital Dividend Spectrum ................................................................... 47
6.3 Planning the Restack......................................................................................................... 49
6.3.1 Core Issues ............................................................................................................. 50
6.3.2 Restack Objectives ................................................................................................. 51
6.3.3 Restack Planning Principles.................................................................................... 52
6.3.4 Television licence area plans.................................................................................. 54
6.3.5 Indicative restack channel chart ............................................................................ 54
6.4 Implementing the Restack................................................................................................ 54
6.4.1 Program Implementation Manager ....................................................................... 54
6.5 Public Information Campaign ........................................................................................... 55
6.6 Planning and Implementation Example............................................................................ 56

xi
Page
Part 7  Summary and Conclusions............................................................................................... 61
7.1 Summary........................................................................................................................... 61
7.2 Key Lessons....................................................................................................................... 62
7.3 The Future......................................................................................................................... 62
7.4 Conclusions....................................................................................................................... 63
Glossary of abbreviations ............................................................................................................ 64
References.................................................................................................................................. 67

1
Part 1 – Country profile
1.1 Population and geographic overview
Australia is an island continent and the world's sixth largest country (7 682 300 km2
). Lying between the
Indian and Pacific oceans, the country is approximately 4 000 km from east to west and 3 200 km from
north to south, with a coastline 36 735 km long.
It is on the whole exceedingly flat (the lowest point on the mainland, Lake Eyre, is 15 m and the highest,
Mount Kosciuszko, is 2 228 m) and dry (less than 51 cm of precipitation falls annually over 70 per cent per
cent of the land area). The coastal regions where most of the population resides comprise many river and
creek valleys requiring additional transmitter sites to provide good terrestrial television coverage.
Canberra is Australia's capital city. With a population of approximately 320 000 people and situated in the
Australian Capital Territory, Canberra is roughly half way between the two largest cities Melbourne and
Sydney. Australia's population is concentrated along the coastal region of Australia from Adelaide to Cairns,
with a small concentration around Perth, Western Australia. The centre of Australia is sparsely populated.
As of October 2014, Australia's population is roughly 23.6 million people1
. The most populous states are
New South Wales and Victoria, with their respective capitals, Sydney and Melbourne, the largest cities in
Australia.
1.2 System of government
The Commonwealth of Australia was formed in 1901 when six independent British colonies agreed to join
together and become states of a new nation. The rules of government for this new nation were enshrined
in the Australian Constitution, which defined how the Australia Government was to operate and what issues
it could pass laws on, generally these are limited to areas that affect the whole country.
The Constitution created a 'federal' system of government. Under a federal system, powers are divided
between a central government and individual states. In Australia, power was divided between the Australia
Government and the six state governments. Laws relating to broadcasting and communications are passed
by the Federal Government.
Although the six states joined together to form the Commonwealth of Australia and the Australia
Government, they still each retain the power to make their own laws over matters not controlled by the
Commonwealth under Section 51 of the Constitution. State governments also have their own constitutions,
as well as a structure of legislature, executive and judiciary. Matters before a state judiciary may result in
suppression orders by the courts for that state. Although not a law relating to broadcasting, such court
orders over the years have influenced the design of broadcaster’s studio and presentation facilities to
provide programming within state boundaries to comply with such court orders.
1.3 Australian broadcast market
1.3.1 Introduction
Australians have access to a range of television services, available on both free-to-air and pay television
platforms.
 The Australian Broadcasting Corporation (ABC) and the Special Broadcasting Service (SBS) provide
national (government-funded) television broadcasting services. The ABC is fully funded from
government, supplemented only by content, services and branding sales whereas SBS is allowed
to raise additional revenue by broadcasting limited advertisements and sponsorship
announcements.
1
Australian Population Clock available at www.abs.gov.au/

2
 Commercial free-to-air television broadcasters provide television services within a specified
licence area. As of 1st
August 2013 there are 64 licensed commercial TV broadcasting services
operating throughout Australia. Commercial free-to-air broadcaster’s principal revenue is derived
from broadcasting advertisements within breaks in programming.
 Community television services provide community based programming. Their revenue is derived
from sponsorships, government grants and donations.
 Narrowcasting television services have reception limited in some way. There are open
narrowcasting services available without cost to consumers, and subscription narrowcasting
services available only on the payment of a subscription fee.
 Subscription television services (pay TV) are funded by subscriptions and limited advertising
revenue.
1.3.2 Terrestrial broadcasting
National, commercial and community broadcasters provide free-to-air via terrestrial broadcasts. The
national broadcasters licences cover the whole country, but their services tend to be organised to cover a
state or even a state capital city.
Commercial broadcasters are licensed to broadcast to a specific licence area, with only three licences
available in any one area, except for some overlap areas between the cities and regional areas where six
licences have been issued. Media ownership laws stipulate that a person must not control television
broadcasting licences whose combined licence area exceeds 75 per cent of the population or more than
one licence within a licence area2
, so the commercial broadcast companies have formed into three capital
city broadcast networks and six regional broadcast networks with programme affiliation agreements which
results in most programming being available Australia-wide on a network of licenced stations but with
different ownership as shown in Figure 1. The capital city broadcasters typically broadcast in Brisbane,
Sydney, Melbourne, Adelaide and Perth (which comprise 66.71 per cent of the population of Australia)3
.
Australia’s population mainly lives in cities and on the coastal fringe. 40.6 per cent of the country live within
the TV licence areas of Sydney and Melbourne, yet these areas only account for 0.33 per cent of the
country’s land area, yielding a population density of 319 people / km2
for broadcasters to cover. Brisbane,
Adelaide and Perth have a further 26.1 per cent of the population living in 0.89 per cent of the country at a
density of 78 people / km2
for broadcasters to cover. Due to historical factors determining licence areas,
approximately 4.3 per cent of the population live in an area where city and regional licence areas overlap.
The regional broadcast licence areas serve 35.7 per cent of the country’s population who live in
15.4 per cent of the country (including the overlap areas). In these areas 6 people live per km2
. In the
remaining remote areas of the country, 2.5 per cent of the population live in 87 per cent of the land mass
at an average density of 0.075 people / km2
.
Full statistics are provided in Table 1 and are shown in Figure 1 where the state capital city licence areas
are indicated in pink and the regional licence areas are shown in shades of blue.
2 Section 53 of the Broadcasting Services Act 1992
3
Licence area populations in the ACMA BSA Section 30 Schedule www.acma.gov.au/webwr/aba/
licplan/planning/licareas/documents/bsa_92_s30_schedule.pdf

3
Figure 1: Australian terrestrial TV licence areas
Source: Regional Television Marketing

4
Table 1: Australian TV licence area statistics4
Licence Area Overlap
Market
Population Pop % Area Area % Pop / km2
Australia 19 813 080 7 682 300
Sydney 4 118 936 20.79% 12 145 0.16% 339.147
Melbourne 3 919 966 19.78% 13 086 0.17% 299.554
Sub Total 8 038 902 40.57% 25 231 0.33% 318.612
Adelaide 1 275 291 6.44% 30 642 0.40% 41.619
Brisbane 2 371 478 11.97% 17 987 0.23% 131.844
Perth 1 529 047 7.72% 17 927 0.23% 85.293
Sub Total 5 175 816 26.12% 66 556 0.87% 77.766
Broadcast Networks Total 13 214 718 66.70% 91 787 1.19% 143.972
Regional Queensland 1 480 612 7.47% 226 640 2.95% 6.533
Northern NSW 1 943 893 9.81% 133 109 1.73% 14.604
Southern NSW 1 273 215 6.43% 176 316 2.30% 7.221
Griffith and MIA 64 164 0.32% 39 690 0.52% 1.617
Regional Victoria 1 052 581 5.31% 190 212 2.48% 5.534
Mildura / Sunraysia 59 861 0.30% 21 343 0.28% 2.805
Riverland 35 201 0.18% 15 878 0.21% 2.217
Spencer Gulf 110 596 0.56% 55 933 0.73% 1.977
Mt Gambier / South East 68 590 0.35% 28 462 0.37% 2.410
Broken Hill 19 561 0.10% 18 669 0.24% 1.048
South West and Great
Southern
287 786 1.45% 88 920 1.16% 3.236
Kalgoorlie 51 770 0.26% 81 237 1.06% 0.637
Geraldton 43 875 0.22% 41 899 0.55% 1.047
Darwin 107 312 0.54% 9 469 0.12% 11.333
Tasmania 473 820 2.39% 51 971 0.68% 9.117
Regional Networks Total 7 072 837 35.70% 1 179 748 15.36% 5.995
Regional Queensland Brisbane 71 424 0.36%
Northern NSW Brisbane 395 885 2.00%
Northern NSW Sydney 298 018 1.50%
Regional Victoria Melbourne 16 046 0.08%
South West and Great
Southern
Perth 68 908 0.35%
Sub Total 850 281 4.29%
Regional Networks Exclusive Market Totals 6 222 556 31.41%
Remote and regional WA 492 922 2.49% 2 519 716 32.80%
less overlaps Various
regional
licence areas
383 431 –1.94% –212 056 –2.76% 0.047
Remote Central & Eastern Australia 393 658 1.99% 4 377 945 56.99% 0.090
Remote Broadcasters Total 503 149 2.54% 6 685 605 87.03% 0.075
4
www.acma.gov.au/Industry/Broadcast/Spectrum-for-broadcasting/Spectrum-digital-television/broadcasting-licence-
areas-television-acma

5
Hence, from a commercial perspective, the state capital city broadcast networks serve two thirds of the
population and enjoy a more accessible market. By contrast, the regional networks cover just over a third
of the country’s population, but face a greater challenge accessing and serving their geographically-large
market. The remote areas provide a further challenge. These characteristics have had a major influence on
the design of each broadcasting network and the different technologies they employ.
1.3.3 Technical broadcast overview
Before digital television, free-to-air broadcasts were transmitted using the phase alternating line (PAL)
colour system with stereo sound as described in ITU-R Recommendations BT.1700, BT.1701 and BS.707 in
a 7 MHz channel raster in VHF Bands I (45-52, 56-70 MHz), II (85-92, 94-108 MHz) and III (137-144,
174-230 MHz) and in UHF Bands IV and V (520-820 MHz).
Each market or licence area is primarily served from a main transmitter which is fed via microwave or fibre
links from the broadcast station. In areas where terrain would degrade reception from this transmitter,
a broadcast site is established to receive the signal from the main transmitter and re-broadcast it on
another channel. These sites are called translator sites, translating the main channel into the local in-fill
channel. Main transmitter and translator sites are under control of the broadcaster, or use a third party
transmission service provider company.
Over the years, government funds have been allocated to a television "black spots" programme to fund the
establishment of a further level of in-fill translators, generally at very low power and operated and
maintained by community organisations or the "third tier" of Australian government, local municipal
councils. Section 212 of the Broadcasting Services Act allows any organisation to retransmit programmes
within the licence area of the broadcaster and Section 212A specifically relates to re-transmission for the
sole or principal purpose of obtaining or improving reception in a small community by self-help providers.
Figure 2: Australian terrestrial TV broadcast overview (Pre digital)
Source: ITU

6
Technically, broadcaster responsibility in delivering a service ends effectively as delivery of a specified field
strength at a level 10m above the ground. The level to be delivered varies according to the type of area
served:
 in the cities in areas of concentrated high rise or dense dwelling structures, an "urban" field
strength is specified;
 in the cities and regional towns and communities with a lower density of households, which may
be single dwelling units, a "suburban" field strength is specified; and
 in other more rural and remote areas where dwellings are sparsely populated and there may be
agricultural land a "rural" field strength is specified.
These levels take account for typical installation parameters and allow for the normally anticipated levels
of signal degradation factors such as locally induced electrical noise.
The services are provided free-to-air, it is then the viewer’s responsibility to organise reception and display
of the television service.
Prior to consideration of conversion to digital transmission in 1993, Australia still had a television
manufacturing facility. Many manufacturers have supply arrangements into the retail stores so Australian
consumers have enjoyed a competitive retail marketplace for television equipment.
The final piece of the transmission chain from broadcaster facility to the viewer’s television is through the
viewer’s antenna and cable distribution structure. The responsibility for this lies with the viewer / consumer
who may contact local antenna installers to perform this work. For viewer’s in high rise or multi-dwelling
unit apartments, the distribution infrastructure may be owned and maintained by the building "body
corporate" who are responsible for shared services into such buildings.
This broadcast structure is supported by a structure of technical standards and government regulatory
authority technical specifications.
1.4 Key stakeholder groups
The broadcast market in Australia comprises key stakeholder groups involved in the transmission chain:
 Broadcasters – as the originators, aggregators and distributors of programme content;
 Government – who wish to see public policy objectives achieved;
 Transmission service providers – an industry segment created out of the economy of scale when
broadcasters have outsourced their transmission facilities;
 Manufacturers / suppliers  who vie for sales in a vibrant television marketplace;
 Retailers – as the conduit between the suppliers and the consumers;
 Installers – a widely distributed small industry completing the broadcast chain between the field
strength transmitted by the broadcasters and the antenna input of the television receiver.
In terms of viewing population, the free-to-air networks with affiliated stations are a dominant force, whilst
the two government-funded national networks (ABC and SBS) also draw significant audiences. There has
been little change over the period of digital conversion with free-to-air television being available in over
99 per cent of household in the country, with over 60 per cent of the population watching each day
(and over 94 per cent watching in a month) for an average time of over 3 hours per day5
.
Hence, touching the bulk of the population each day, free-to-air broadcast television plays a central role in
Australian society and is therefore in a position of power and influence in society. Accordingly, any change
to broadcast television attracts additional influencing stakeholders:
5
Free TV Stats & Graphs available from www.freetv.com.au/content_common/pg-free-tv-stats-and-graphs.seo

7
 Special interest lobby groups – seeking to impose on media policy an access right, for example
advocacy groups for deaf people have influenced the number of programmes produced with
open captions, groups representing actors have influenced the regulations on number of hours
of locally produced drama, children’s television groups have influenced the number of hours and
timing of broadcasts of programming suitable for children;
 Competitors – mainly other media interests such as print media who seek a competitive place in
society for news; and
 Other broadcast platforms – subscription television interests that would prefer to limit the free-
to-air broadcast sector and hence lessen competition for their platforms.
At every stage of the digital conversion process for free-to-air terrestrial broadcasting, reviews by
government have taken submissions and been influenced by this wide group of stakeholders, often with
opposing views and desired outcomes. Australia, as an open democratic society has taken account of these
influences sometimes to the detriment of the broadcast system.
The cost impact of public policy objectives on broadcasters is not uniform across Australia. As noted in
Section 1.3.2 above, broadcast networks serving the main capital cities are seen to have a greater capacity
to absorb the costs of additional policy requirements, for example digital rollouts were imposed sooner
than for regional networks. Subsidies from government projects have flowed towards regional and to a
greater extent to remote broadcasters to achieve the policy objective of universal television coverage.
Whilst this does imply high subsidies on a per capita basis in rural and remote areas, for a very large part of
the country, the population levels are relatively low but have significant economic importance to the
country from agricultural and mining activities which are the main contributors to Australia’s export
income.
1.5 Policy, legal and regulatory frameworks
Television plays a central part in the life of many Australians, being their primary source of news, current
affairs, live sport and quality Australian drama programmes. As an island continent that spans a wide range
of geography from the tropical north to the temperate south plus vast desert areas in-between and spread
over a number time zones (Australia is in the unique position of changing time zones east / west as well as
north / south in summer-time to encompass five time zones), local content obligations in broadcasting are
also paramount. Given this role, many aspects of free-to-air television are highly regulated by government
to ensure their public policy outcomes are maintained which influence many parts of Australian life. This
level of regulation ensures there is a constant dialogue between various arms of government, broadcasters
and other key stakeholders.
1.5.1 Government and regulatory authorities
(i) Minister
Within the executive arm of government, responsibility for broadcasting lies within the communications
portfolio of the Minister for Communications.
(ii) Department
The Minister has a Department of Communications reporting to him to provide good public policy advice
to the government, so the Department must establish and maintain a deep and authoritative understanding
of market developments and innovations, including international and domestic6
. The Department also
administers portfolio legislation and is tasked to deliver efficient and effective programmes to achieve the
government policy outcomes.
6
From The Secretary’s Introduction to the Corporate Plan 2014-17 www.communications.gov.au/about_us

8
(iii) Regulator
The Australian Communications and Media Authority (ACMA) is the converged regulator for
telecommunications, broadcasting, the Internet and also manages radio spectrum. Everything except for
telecommunication competition regulation, which is handled by the economy wide competition regulator
the Australia Competition and Consumer Commission (ACCC). Both regulators are independent. While the
Minister has a number of important powers in a number of areas, he interacts with the regulators at arms
length.
The ACMA plans the availability of segments of the broadcasting services bands for analogue and digital
broadcasting7. It can allocate, renew, suspend and cancel broadcasting licences and collect any fees payable
for those licences. It also allocates pay TV licences and administers the class licence regime for subscription
radio broadcasting and open and subscription narrowcasting services.
In addition, the ACMA is required to inform itself and the Minister about advances and trends in
broadcasting technology.
(iv) Department and regulatory authority changes
Over the 21 years since digital television was first investigated, the name of the Department has gone full
circle, for reference throughout this document the following organisations were the responsible
government department;
1993-1994 Department of Communications
1994-1998 Department of Communications and the Arts
1998-2007 Department of Communications, Information Technology and the Arts (DCITA)
2007-2013 Department of Broadband, Communications and the Digital Economy (DBCDE)
2013-present Department of Communications
This period has also seen the merger of the broadcasting and communications regulators into a single body.
1992-2005 Australian Broadcasting Authority (ABA)
1993-1997 Spectrum Management Authority (SMA)
1997-2005 Australian Communications Authority (ACA, a merger of SMA and AUSTEL)
2005-present Australian Communications and Media Authority (merger of ABA and ACA)
1.5.2 Industry co-regulation
Under communications and media legislation, self- and co-regulatory arrangements require industry
participants to assume responsibility for regulatory detail within their own sectors, and this is underpinned
by clear legislative obligations, with the regulator maintaining reserve powers. These arrangements provide
flexibility for the ACMA, as the regulator, to exercise a variety of roles dependent on the nature of the
concern, such as whether the issue is a policy matter or market issue. This includes the flexibility to not
intervene to allow market-based solutions to develop, provide advice to government on policy issues, or
encourage industry-developed solutions.
Co-regulation generally involves both industry and government (via the regulator) developing,
administering and enforcing a solution, with arrangements accompanied by a legislative backstop.
In relation to commercial television, Free TV Australia and its membership have developed the Commercial
Television Code of Practice8
which covers matters prescribed in Section 123 of the Broadcasting Services
Act and other matters relating to programme content that are of concern to the community including:
7
Part 3 of the BSA
8
Available from www.freetv.com.au/content_common/pg-code-of-practice-.seo

9
 programme classifications;
 accuracy, fairness and respect for privacy in news and current affairs;
 advertising time on television;
 placement of commercials and programmes promotions; and
 complaints handling.
The Commercial Television Code of Practice calls on broadcasters to resolve complaints with members of
the public in the first instance, but these may be escalated to the ACMA for resolution of the complaint.
Similar arrangements are in place with the national broadcasters, for example the Australian Broadcasting
Corporation (ABC) Board is required, under section 8(1)(e) of the ABC Act, to develop a code of practice
relating to its television and radio programming, and to notify this code to the ACMA9.
Co-regulation occurs in many industries including the media as shown in Figure 3.
Figure 3: Australia television environment – regulatory players10
Source: Australian Department of Communications
9
Available from http://about.abc.net.au/reports-publications/code-of-practice-2014/
10
Adapted from information in presentations available on the ACMA website.

10
1.5.3 Legislation
(i) Radiocommunications Act 1992
In line with the growing liberalisation of the radiocommunication sector in the early 1990s, the
Commonwealth Government enacted the Radiocommunications Act 199211
(RCA), which provided the basic
framework for the management of the radiofrequency spectrum based on the following objectives:
(a) maximise, by ensuring the efficient allocation and use of the spectrum, the overall public benefit
derived from using the radiofrequency spectrum;
(b) make adequate provision of the spectrum for use by public or community services;
(c) provide a responsive and flexible approach to meeting the needs of users of the spectrum;
(d) encourage the use of efficient radiocommunication technologies so that a wide range of services
of an adequate quality can be provided;
(e) provide an efficient, equitable and transparent system of charging for the use of spectrum, taking
account of the value of both commercial and non-commercial use of spectrum;
(f) support the communications policy objectives of the Commonwealth Government;
(g) provide a regulatory environment that maximises opportunities for the Australian
communications industry in domestic and international markets;
(h) promote Australia’s interests concerning international agreements, treaties and conventions
relating to radiocommunications or the radiofrequency spectrum.
The RCA established the Spectrum Management Agency (SMA), a statutory agency within the Transport
and Communications portfolio, on a cost-recovery basis. The Minister retained responsibility for, and
general policy control over, the agency. The SMA has subsequently become part of the Australian
Communications Authority which has now been merged with the ABA to form the ACMA.
The market-based reforms which inspired the RCA included a new category of licence called "spectrum
licensing" (together with the ongoing apparatus and class licensing systems) whereby licences assigning less
prescriptive spectrum rights would allow to operate radiocommunication transmitters in a specified
frequency band and geographical area, with the ability to trade or lease licences. Other reforms included
the selective and progressive introduction of auctions for some licences in some frequency bands.
This more market-oriented licensing regime was seen as a necessary adjunct to the introduction of
competition between telecommunication carriers with rival demands for radio frequency allocations.
At the same time, a more flexible radio frequency regime was introduced for setting technical standards
and managing conformity with standards.
Section 31 of the RCA provides for the Minister to:
(a) designate a part of the spectrum as being primarily for broadcasting purposes or restricted
datacasting services, or both; and
(b) refer it to the ACMA for planning under Part 3 of the Broadcasting Services Act 1992.
At the time the Act was established, this mechanism handed over administration and planning of the
Broadcasting Services Bands to the ABA (now part of the ACMA), whereas from a radio spectrum
perspective, all other bands are administered under the RCA.
11
www.comlaw.gov.au/Details/C2013C00586

11
(ii) Broadcasting Services Act 1992
The "broadcasting services bands" so designated by the Minister in Section 31 of the RCA are managed
through the Broadcasting Services Act12
(BSA) 1992 as amended which is the main legislative instrument
governing terrestrial broadcasting in Australia and defines the role of the regulatory authority (originally
the Australian Broadcasting Authority and now the Australian Communications and Media Authority), gives
the regulator a range of powers and functions, and sets out explicit policy objectives. The regulator is
independent from, and has a separate legal identity to, the Australia government.
1.6 Planning and licencing
1.6.1 Analogue planning
The BSA sets out three stages for the planning process for the broadcasting services bands:
 determination of priorities for the planning of services using the broadcasting services bands
[s.24];
 preparation of a frequency allotment plan (FAP) [s.25]; and
 preparation of licence area plans (LAPs) [s.26].
The LAP is a legislative instrument determines the number and characteristics, including technical
specifications, of broadcasting services that are to be available in particular areas of Australia with the use
of the broadcasting services bands, and those plans must be consistent with the relevant frequency
allotment plan13
.
The LAPs specify all the technical characteristics of the analogue broadcast service for the broadcaster and
define the licence area over which they have rights to broadcast. Before issuing a final LAP, the ACMA
release a draft for comment and seek submissions. At this time a discussion paper is released offering
background on the selection of various characteristics. This provides the broadcaster an opportunity to
review and seek changes prior to the final plan being released. The benefits of this consultation for both
parties are to bring together a national planning view via the regulator enhanced by the local knowledge of
the broadcaster to avoid instances where local conditions may not conform to planning models.
1.6.2 Digital terrestrial television broadcasting (DTTB) planning
(i) Commercial and national television conversion schemes
Schedule 4 to the BSA sets out arrangements for the conversion, over time, of the transmission of television
broadcasting services from analogue to digital mode. Under the arrangements, the ABA (now ACMA) was
required to formulate two schemes for the conversion – a commercial television conversion scheme, and
a national television conversion scheme:
 the Commercial Television Conversion (CTC) scheme was formulated in March 1999. The scheme
commenced on 9 June 1999. The ABA varied the CTC scheme on 21 December 2000;
 the National Television Conversion (NTC) scheme was formulated in December 1999. It was
approved by the Minister on 2 February 2000, and commenced on that date. The Minister
approved a variation to this scheme on 20 December 2000.
12 www.comlaw.gov.au/Details/C2014C00649
13
Final LAPs are available from www.acma.gov.au/Industry/Broadcast/Spectrum-for-broadcasting/Spectrum-radio-
broadcasting/final-licence-area-plans-broadcast-planning-acma

12
(ii) Digital channel plans (DCPs)
Under both schemes, the ABA (now ACMA) was required to make digital channel plans that allotted
additional channels to broadcasters so as to enable them to transmit programmes in analogue and digital
modes during a simulcast period (originally foreseen to last 8 years). Incumbent television broadcasters
were provided additional spectrum to simulcast their analogue signal in digital form during the conversion
period. At the end of the conversion period, the spectrum used for analogue transmission was returned to
the regulator.
(iii) Television licence area plans (TLAPs)
Television licence area plans are the long-term planning instruments for television broadcasting services,
and are the primary instruments for managing the restack of television broadcasting services. Restack refers
to the process of clearing digital television services from the digital dividend band (694-820 MHz). A TLAP
identifies channel allotments for digital television services, details any necessary changes and a timeframe
for those changes. Once TLAPs come into effect they replace the licence area plans (LAPs) and digital
channel plans (DCPs) for those areas.
(iv) Technical planning guidelines
Under section 33 of the Broadcasting Services Act 1992, the ACMA is required to prepare technical
guidelines for planning radio and television services that use the broadcasting services bands. The Technical
Planning Guidelines (TPGs) contain mandatory technical requirements for commercial, community
(including temporary community) and datacasting licensees, when planning and operating new
transmission facilities or proposing changes to existing facilities.
The guidelines cover both analogue and digital television as well as other broadcast services and specify the
emission characteristics. For the analogue service this inherently specifies baseband characteristics as well,
but for digital television the document relies on a reference to the modulation characteristics in the
Australian Standard AS4599.1-2007, hence providing a link between the digital transmission standard and
the BSA.
The linkages between the BSA and other technical documentation are shown in Figure 4.
Figure 4: BSA links to technical planning
Source: ITU

13
(v) DTTB Planning Handbook
All technical and general assumptions considered by the ABA (now ACMA) to develop DCPs are set out in
the DTTB Planning Handbook – March 200514
.
1.6.3 Licensing
There are two types of licences relevant to broadcasting; a broadcasting licence and apparatus licences.
A broadcasting licence not only gives the broadcaster the right to broadcast the service, it also confers a
right to use the broadcasting services bands to transmit the service. Therefore, in its statutory role for
planning and licensing the broadcasting services bands, the ACMA issues most broadcasters with apparatus
licences that grant them access to the spectrum when they receive their broadcasting licence.
Most of the broadcasting licences carry the entitlement to sufficient spectrum to maximise coverage in a
market or licence area while minimising coverage outside it. These broadcasting licences may be transferred
as a complete package, but it is not possible under the current regulations to transfer access to the spectrum
separately from the licence to broadcast.
The transition to digital, requiring a second channel to simulcast analogue and digital services during the
transition period, has seen considerable debate in Australia in recent years regarding the methods for
allocation and charging of broadcasting spectrum. Much of the policy debate is around what broadcasters
do under the banner of public interest to make culturally and socially valuable content accessible to large
numbers of people, and how to place a value on that content.
1.6.4 Television spectrum
Australia has a 7 MHz channel raster in VHF Bands I, II and III and in UHF Bands IV and V as shown in Table 2.
14
www.acma.gov.au/~/media/Licence%20Issue%20and%20Allocation/Publication/pdf/Digital%20Terrestrial%20
Television%20Broadcasting%20Planning%20Handbook%20including%20technical%20and%20general%20assumptions.pdf

14
Table 2: Channels for the Australian Terrestrial Television Service15
VHF UHF
BAND I(1)
BAND IV 47 659-666 MHz
0 45-52 MHz 27 520-526 MHz 48 666-673 MHz
1 56-63 MHz 28 526-533 MHz 49 673-680 MHz
2 63-70 MHz 29 533-540 MHz 50 680-687 MHz
30 540-547 MHz 51 687-694 MHz
31 547-554 MHz 52 694-701 MHz
BAND II(1)
32 554-561 MHz 53 701-708 MHz
3 85-92 MHz 33 561-568 MHz 54 708-715 MHz
4 94-101 MHz 34 568-575 MHz 55 715-722 MHz
5 101-108 MHz 35 575-582 MHz 56 722-729 MHz
57 729-736 MHz
BAND V 58 736-743 MHz
BAND III 36 582-589 MHz 59 743-750 MHz
5A(2)
137-144 MHz 37 589-596 MHz 60 750-757 MHz
6 174-181 MHz 38 596-603 MHz 61 757-764 MHz
7 181-188 MHz 39 603-610 MHz 62 764-771 MHz
8 188-195 MHz 40 610-617 MHz 63 771-778 MHz
9 195-202 MHz 41 617-624 MHz 64 778-785 MHz
9A(3)
202-209 MHz 42 624-631 MHz 65 785-792 MHz
10(4)
208-215 MHz (superseded) 43 631-638 MHz 66 792-799 MHz
209-216 MHz (current) 44 638-645 MHz 67 799-806 MHz
11(4)
215-222 MHz (superseded) 45 645-652 MHz 68 806-813 MHz
216-223 MHz (current) 46 652-659 MHz 69 813-820 MHz
12(3)
223-230 MHz
Note 1  Television Band I (channels 0, 1 & 2) and Band II (channels 3, 4 & 5) are not being considered for new
analogue television services or for the introduction or ongoing transmission of digital television services.
Note 2  VHF channel 5A is currently within the Broadcasting Services Bands (BSB) and has been recommended
for clearance by ACMA to allow for the introduction of Low Earth Orbiting (LEO) satellites. Channel 5A is not
being considered for new analogue television services or for the introduction or ongoing transmission of digital
television services.
Note 3  Clearance of radiocommunication services from 202-208 MHz and from 222-230 MHz has allowed a
revised channel arrangement to be implemented. The current channel arrangement has two new channels
(channels 9A and 12). To accommodate channel 9A, channels 10 and 11 were shifted up in frequency 1 MHz.
Note 4  The majority of existing services on channels 10 and 11 were assigned using the superseded channel
arrangement. Services on channels 10 and 11 may be required to shift in frequency to align with the current
channel arrangement. Any such requirement will be considered on a case-by-case basis. New services on
channels 10 and 11 will be assigned according to the current channel arrangement i.e. channel 10 (209-216 MHz)
and channel 11 (216-223 MHz).
15
Appendix 5 of Broadcasting Services (Technical Planning) Guidelines 2007as amended www.comlaw.gov.au/
Details/F2009C01061

15
1.6.5 Standards
Section 130A of the BSA provides that the ACMA may, by legislative instrument, determine technical
standards that relate to digital terrestrial transmission. The ACMA have not made such an instrument, but
have regulated the digital emission characteristics by reference to the Australian Standard AS4599.1-2007
in the Technical Planning Guidelines, which are a legislative instrument.
Similarly Section 130B of the BSA provides that the ACMA may, by legislative instrument, determine
technical standards that determine technical standards that relate to domestic digital television reception
equipment. Government policy in Australia maintains a free market for supply of television receivers so no
regulations regarding the digital reception aspects of receivers have been made. Other aspects such as
electrical safety and electromagnetic radiation have been regulated for consumer products and these
regulations apply to digital television receivers.
1.7 Roadmap overview
The roadmap of the transition from analogue to DTTB has five stages as shown in Figure 5:
 Stage 1 – Preparation and planning
 Stage 2 – Implementation
 Stage 3 – Digital enhancement
 Stage 4 – Analogue switch off, and
 Stage 5 – Digital restack.
Figure 5: Australian transition timeline
Source: Department of Communications and ACMA
1.7.1 Stage 1 – Preparation and planning
This stage initially involved Australian experts contributing to the development work in the ITU-R Study
Group 11 and in particular, Task Group 11/3.
Studies within Australia were brought together under a Specialist Group drawn from government and
industry and led by the regulator at the time, the Australian Broadcasting Authority which recommended
adoption of DTTB in 1997. Exhaustive testing and evaluation of ATSC and DVB-T by government and industry
experts led to the decision to recommend the DVB-T system for Australia.

16
Having the technical foundations in place, government policy was announced supporting legislation passed
in 1998. This formed the basis for the regulator to commence planning the simulcast of analogue and digital
services and undertake appropriate licencing. At the same time government and industry met to develop
technical standards for the system.
1.7.2 Stage 2 – Implementation
In 2000, a year prior to the first DTTB transmissions, broadcasters commenced installation of digital
headend and transmission equipment. DTTB formally commenced in Sydney, Melbourne, Brisbane,
Adelaide and Perth on 1st
January 2001. Initially services were planned to have an eight year simulcast with
digital, regional areas were scheduled three years later.
This was a period of approximately six years which allowed broadcasters to test various aspects of the digital
system and for engineers to focus on refinement of the transmission network. Digital take up by consumers
provided a better statistical base for viewer complaints so reception issues could be investigated.
Refinements were made to the service information inherent in digital broadcasts and the development of
electronic programme guide information. After the initial rollout of transmitters at existing broadcasting
sites, there was a period of stability in the broadcast networks.
1.7.3 Stage 3 – Digital enhancement
With the pending closure of the analogue service in sight, broadcasters commenced an intensive review of
digital coverage. Garnering the experience gained from the Implementation Stage, each licence area was
reviewed to investigate methods of cost-effectively enhancing coverage in areas where the digital service
was proving to not be completely reliable.
Special attention was given to planning spectrum for these additional sites as the television broadcasting
spectrum was already heavily congested.
1.7.4 Stage 4 – Analogue switch off
Extensive planning was needed to ensure that the viewing public will not be impacted by the switch off of
analogue service as it was a complex process. The government established a Task Force to plan the switch
off of analogue services which had to liaise widely with broadcasters and other industry sectors to ensure
that all facilities were in place in preparation for the switch off.
Actual conversion status needed to be quantified and assistance programmes developed. Switch-off was
planned to occur in stages by licence area.
1.7.5 Stage 5 – Digital restack
Government made a policy decision to auction the 694-820 MHz spectrum band as a "Digital Dividend" in
2012 before the switch off was completed which required the planning of the restack of digital services
co-incident with planning the switch off. Methods for restacking were examined, resourcing was a key issue
and public information campaigns devised.
Considerable spectrum planning was undertaken to ensure that a restack of services in a licence area did
not cause interference into an adjacent licence area.

17
Part 2 – Preparation and planning
2.1 System selection
2.1.1 Origins for considering digital
Australian television broadcast engineers have been involved throughout the development of HDTV and
digital television broadcasting, from the debates on HDTV standards from the mid 1980’s. In particular,
Australian delegations to the International Telecommunication Union (ITU-R) forums have consistently
pressed for a common international standard for digital television. The ITU was seen to be the main forum
in which to argue for convergence of globally harmonised television standards for the new technology
choices, so as to avoid the need for continuing standards conversion within the exchange of programme
content and consequent operational and quality difficulties.
From about 1990 it became apparent that work on development of analogue HDTV standards based on
proposals from Europe, the USA and Japan was becoming deadlocked because of the unavoidable linkages
between system standards and the respective regulatory, planning and operational environments of the
countries of origin. In addition, none of the analogue HDTV proposals was particularly attractive for use in
Australia. In the same time frame, work in the ISO/IEC JTC-1 MPEG group on compression systems and in
other related fields indicated that digital technologies might offer viable new solutions for consumer
services in television broadcasting.
From its monitoring of developing technologies, the then Federation of Australian Commercial Television
Stations (FACTS – now Free TV Australia) Engineering Committee became confident that digital compression
and transmission would evolve into practical technologies to carry terrestrial broadcasting into the new
millennium. It established a specialist group to study the subject, particularly the early developments in the
US. While European broadcasting technology was concentrating on the development of Multiplexed
Analogue Component (MAC), FACTS saw little benefit in the MAC technology for terrestrial broadcasting.
The commercial broadcasting structure of Australian television depends heavily on local programming and
local advertising revenue. The European technology was fundamentally directed to satellite distribution,
not suited to distribution to smaller locally-concentrated broadcasting markets.
Early work on the use of Orthogonal Frequency Division Multiplexing (OFDM) published by the IBA in the
UK and in other European studies showed similar promise to parallel work on a system to develop HDTV
terrestrial broadcasting in the USA. The Australian broadcasting experts identified a need for the ITU to
provide a common forum where these disparate studies could be drawn together in an attempt to evolve,
for the first time, a world- wide common system of television broadcasting. As a result of an Australian
proposal to ITU-R Study Group 11, Task Group 11/3 was established with the objective of preparing a
common set of digital terrestrial television broadcasting (DTTB) standards. Task Group 11/3 was very
successful in fostering a high level of convergence between the North American and European DTTB
systems, except for the modulation system. In the US, a single carrier 8VSB modulation system was formally
adopted. European countries confirmed their adoption of a multiple carrier Coded Orthogonal Frequency
Division Multiplex modulation system (COFDM). Towards the end of the studies of Task Group 11/3, Japan
announced that it was working on a third modulation variant which would offer segmentation of the RF
channel.
2.1.2 ABA Specialist Group on Digital Terrestrial Broadcasting
In 1993 a group of specialists was drawn together by the broadcasting regulator at the time the Australian
Broadcasting Authority, Department of Transport and Communications, in addition to broadcasters and
manufacturers. The ABA Specialist Group was intended to bring together studies taking place in a number
of Australian forums and investigate potential options and policies relating to digital television.

18
In 1995 the group released a report, Digital Terrestrial Broadcasting in Australia, containing the preliminary
conclusions of the group. It made the observation that picture quality was an early driver of digital:
For decades television engineers have striven to deliver the picture quality they have been able
to generate in the studios to home viewers. Their efforts have been hampered by the inherent
limitations of the analogue [sic] system. Now, with digital video technology it is possible to
realise this ambition16.
However, It found that premature regulation of the new platform might stifle the market-driven
development of the service, that it should be based upon existing standards, and should not restrict the
ability of broadcasters to tailor local content. It was too early at the time to make decisions relating to what
standard should be used, when transmissions should commence, and whether analogue television should
be phased out.
The final report, was released in February 199717
, recommending to government that:
 Australia should adopt a single system standard for DTTB after completion of detailed technical
evaluation trials in Australia of candidate systems;
 DTTB should be implemented in Australia with digital high definition television (HDTV) capabilities
available from the outset;
 all existing licensed commercial and national television services should be given access to a full 7
MHz bandwidth DTTB channel and be given full control over the use of the delivery capacity of
that channel;
 the year 2000 could be a useful target date for commencement of permanent DTTB broadcasting
in Australia (and the commencement of the development phase). The period between now (1997)
and the commencement in 2000 might be regarded as an experimental phase; and
 the eventual termination of PAL analogue services after the commencement of DTTB services in
Australia should be driven by market factors and subject to regular review. The decision should
be made in the light of findings and in consultation with both government and industry
organisations.
In July 1997 the ABA responded to the Specialist Group's report with its Paper, Digital Terrestrial Television
Broadcasting, which recommended to the government that it support the early introduction of DTTB into
Australia. It considered that DTTB should be a free-to-air service rather than a form of pay TV and it
endorsed the loan of a 7MHz channel to each of the ABC, SBS and each commercial network, as this would
enable the introduction of HDTV from the outset18
.
In April 1998, the Australia government announced its policy to introduce digital television throughout the
country from January 2001.
2.1.3 Broadcaster-led specialist group
As the Specialist Group on DTTB work concluded, the FACTS Engineering Committee resumed its direct
involvement in DTTB by re-establishing the Specialist Group DTTB. The Specialist Group was instrumental
in organising the first experimental broadcasting of DTTB in Australia. This broadcast from the Nine Network
in Sydney occurred during the final meeting of Task Group 11/3 in Sydney, Australia, in November 1996.
16 Australian Broadcasting Authority (ABA), Specialist Group on Digital Terrestrial Broadcasting, Digital terrestrial television
broadcasting in Australia, First report, ABA, 1995, p. 13.
17
Australian Broadcasting Authority. Specialist Group on Digital Terrestrial Broadcasting, “Digital terrestrial television
broadcasting in Australia: final report of the Australian Broadcasting Authority Digital Terrestrial Television Specialist Group.”
Available in hard copy only refer to http://trove.nla.gov.au/work/9829292?q=+&versionId=45821709 for locations.
18
Bills Digest No. 178 1997-98 Television Broadcasting Services (Digital Conversion) Bill 1998 www.aph.gov.au/
Parliamentary_Business/Bills_Legislation/bd/BD9798/98BD178

19
A programme of tests to evaluate both DVB-T and the ATSC systems was drawn up and progressed over the
following year, focussing on operation in a 7 MHz channel and adjacent to the existing analogue
transmissions to test the viability of a "simulcast" between analogue and digital. It should be noted that the
ISDB system in development in Japan was not tested or considered, as it was not expected to be sufficiently
advanced to meet the scheduled Australian commencement date of 2001. These tests which remain today
as the only directly comparative tests conducted in the world, provided a solid technical basis for the
selection of the DTTB system to be used in Australia and involved extensive laboratory and field testing of
the two systems during 1997. The laboratory evaluations were conducted in the government
Communications Laboratory facilities in Canberra by Laboratory staff assisted by experts from the industry.
The field tests were supervised by experts from FACTS members, assisted by the Communications
Laboratory staff, the Australian Broadcasting Authority and a consultant employed by FACTS.
From the outset it was recognised that the ATSC system parameters are mainly fixed and deliver a total
useable data rate of 19.39 Mbps whilst the DVB system offered a range of operating modes, ranging from
low data payloads with rugged coverage ability to higher payloads with less rugged coverage capability, so
a DVB-T mode that provides a payload of 19.35 Mbps was chosen to be similar to ATSC. The payload was
based on the findings of the ABA Specialist Group which indicated that a payload in the order of 20 Mbps is
desirable in order to meet the HDTV objectives of the 7 MHz service.
In the assessment of the test results, the DTTB Selection Panel felt that there was insufficient information
for technical assessment of some relevant criteria. In particular, this applied to translator performance,
indoor antenna performance and carriage through Master Antenna Television systems. It was considered
that each of these matters would require further testing and evaluation.
2.1.4 Selection panel
The Selection Panel was given the responsibility of analysing the comparative tests and other available
information, establishing the relevance of the performance differences to Australian broadcasting, and
recommending the system to be used.
The Panel was unanimous in its view that all free-to-air television broadcasters should use a common
standard to ensure commonality of equipment and minimum cost to viewers. The evaluation process which
was used assisted in clarifying the merits of each system in the context of the Australian broadcasting
environment, and the process of planning for the transition to digital television.
Starting from an initial list of some 50 possible criteria, the Panel researched, analysed and refined the list
to those criteria that were considered to have relevance for the selection. Individual elements were
grouped into five sets of related criteria:
 Group 1 – Coverage; population served based on transmitting from the existing analogue
transmission sites, consideration of reception capability using rooftop vs set-top antennas and
the possibility of mobile reception, performance when broadcast within channels with the
existing analogue system and the impacts of degradations e.g. co-channel and adjacent channel
performance, multi-path performance, immunity to electrical noise and the any effects of using
cabled or MATV systems.
 Group 2 – System Design Elements; combining to use common transmit antenna systems,
implementation of translators, common channel translator capability, the potential to re-purpose
existing transmitters.
 Group 3 – Operational Modes Supported, ability to transmit HDTV, closed captions, multi-
language audio and multi-channel audio.
 Group 4 – Overall System; accepted rather than unique HDTV system, operation and payload
capability in 7 MHz channels, overall encode/decode delay, system upgrade capability.
 Group 5 – Receiver Elements; availability and features, MP@HL capability, availability of receivers
with both PAL and DTTB capability, consideration of design for unique Australian conditions,
software upgrades, lock-up time and ability to provide automatic channel selection for Australian
channelling.

20
Based on these assessment of all criteria, related to the agreed weighting factors, the DTTB Selection Panel
found a clear indication in favour of DVB-T. It further noted that even if the further testing of indoor
reception indicated preference for ATSC, the overall assessment would still lead to DVB, based on the
assessments and the weighting factors applied to the respective criteria.
In June, 1998, the Selection Panel unanimously agreed to recommend that the DVB-T system of modulation
be used for DTTB in Australia19.
2.1.5 Planning implications
From the result of laboratory and field tests undertaken by the Specialist Group DTTB, the concept of mixing
analogue and digital channels in the broadcast band with acceptable levels of degradation to the analogue
service was proven. The test results were a critical input to a group the ABA established to consult regarding
the digital channel plans, the Digital Television Channel Planning Consultative Group (DTCPCG).
The important work of a subgroup of the DTCPCG is recorded in Appendix A of the ABA’s DTTB Planning
Handbook regarding how to implement digital services with the same level of coverage as analogue services
and potential reception quality.
The conclusion was to transmit digital signals at an effective radiated power 6 dB below the analogue
service.
Two approaches to deriving planning values for defining field strength were studied; a ‘ratio approach’ and
a ‘first principles approach’. provides the derivation for the ‘first principles approach’ which the figures
were rounded to the nearest dB to set the planning levels20
.
Table 3: Derivation of field strength for DTTB in Australia21
Band III Band IV Band V
Parameter Unit Rural Sub-
urban
Urban Rural Sub-
urban
Urban Rural Sub-
urban
Urban
Frequency MHz 230 230 230 582 582 582 820 820 820
Equivalent Noise
Bandwidth
MHz 6.7 6.7 6.7 6.7 6.7 6.7 6.7 6.7 6.7
Receiver Noise
Figure
dB 6 6 6 7 7 7 8 8 8
Receiver Noise
Input Voltage
dBuV 9.0 9.0 9.0 10.0 10.0 10.0 11.0 11.0 11.0
Required
Threshold C/N
dB 20 20 20 20 20 20 20 20 20
Minimum
Receiver Input
Voltage
dBuV 29.0 29.0 29.0 30.0 30.0 30.0 31.0 31.0 31.0
Antenna Gain dBd 8 5 5 11 8 8 12 9 9
Feeder loss dB 3 2 2 4 2.7 2.7 5 3.4 3.4
Antenna Factor dB 8.5 10.5 10.5 14.6 16.3 16.3 17.6 19.0 19.0
19 Digital Terrestrial Television Report of the DTTB Selection Panel, FACTS, June, 1998
20 Australian television planning sets three different planning levels to cater for the variation in the Australian environment:
rural, suburban and urban levels. Although not strictly defined, they are intended to plan for the inner urban areas of cities,
the surrounding outer suburban areas and regional and remote rural areas. The planning model is calculated on a nominal
receiver configuration and allowances for the variations in expected interference, noise and antenna location availability.
Only the rural field strength is used as the absolute definition of whether a broadcaster is serving their licence area.
21
Digital television planning based on DVB-T mode 64-QAM with 2/3 FEC and a 1/8 guard interval

21
Band III Band IV Band V
Parameter Unit Rural Sub-
urban
Urban Rural Sub-
urban
Urban Rural Sub-
urban
Urban
Minimum Field
Strength
dBuV/m 37.6 39.6 39.6 44.6 46.3 46.3 48.6 49.9 49.9
Location
Availability
Margin
dB 4.0 6.5 8.5 4.5 7.0 9.0 4.5 7.0 9.0
Time Availability
Margin
dB 0 0 0 0 0 0 0 0 0
Multipath
Margin
dB 0 2 4 0 2 4 0 2 4
Height Gain
Allowance
dB 0 5 6 0 6 8 0 6 8
Environmental
Noise Allowance
dB 1 3 7 0 1 3 0 1 2
Interference
Margin
dB 1 1 1 1 1 1 1 1 1
Resultant
Operating F.S.
dBuV/m 43.6 57.1 66.1 50.1 63.3 71.3 54.1 66.9 73.9
These values are reasonably close to values derived from ITU-R Recommendation BT.1368, as is noted in
ITU-R Report BT.2140-7, Appendix 1 to Part 2, Section 1.6.1:
Australian digital television planning is based on provision of minimum median field strength levels in
rural environments of 44, 50 and 54 dB(V/m) in Bands III, IV and V respectively. These values are
reasonably close to the values that can be derived from the sample calculation value provided in
Table 53 (§ 6) of Annex 2 to Recommendation ITU-R BT.1368-10, once a location correction factor22,
bandwidth adjustment 23 and interference margin 24 are applied. The Australian values for rural
environments are, respectively, 0.3 and 0.1 dB lower, and 1.8 dB higher than values that would be
derived from the Recommendation, for Bands III, IV and V, respectively.
The differences are due to: inclusion of a 1 dB higher receiver noise figure allowance in Bands III and V;
inclusion of a 1 dB allowance for man-made noise in VHF Band III; different combinations of antenna
gain/feeder loss in Bands III and IV; and, use of frequencies at the top rather than the middle of each
band as the reference frequency for the calculation.
22
Australian planning is based on provision of a service at 80% of locations within 200 m by 200 m areas for rural
environments. A 4.5 dB correction factor is applied to convert from a 50% of locations to an 80% locations field strength
value.
23 A 0.5 dB lower noise power applies due to the receiver bandwidth being 6.7 rather than 7.6 MHz.
24
The minimum field strength calculations also include a 1 dB “interference margin” for the support of co-channel frequency
reuse planning.

22
2.2 Government decisions
On the 24 March 1998 the Minister for Communications, the Information Economy and the Arts, announced
the government decisions on the introduction of digital television. The key elements were as follows25:
 the commercial and national free-to-air television broadcasters (FTAs) will be loaned 7 MHz of
spectrum free of upfront charge. In return they will be required to simulcast their existing service
in analogue and digital format for eight years, after which they will have to return the equivalent
of their loaned spectrum to the Commonwealth;
 the FTAs will be required to commence DTTB in metropolitan areas by 1 January 2001 and in
regional areas from that date onwards so that all areas have DTTB by 1 January 2004;
 Following the start-up of DTTB, the FTAs will be required to broadcast minimum levels of HDTV,
with these levels increasing over time. If the FTAs do not comply with these requirements they
will forfeit their loaned digital spectrum.
As well as decisions relating to FTAs providing competition to other industry sectors (not being able to
datacast in the loaned spectrum without paying additional fees, not allowed to multi-channel or provide
subscription television services) and in return a prohibition on new commercial FTA entrants will be
extended until December 2008. The current Australian local programme content requirements will
continue to apply in the digital environment and closed captioning provisions were included for news and
current affairs programmes as well as the establishment of committees to advise on regulatory and
technical matters relating to the conversion. The government was still considering the funding
requirements for the ABC and SBS for digital conversion, as well as whether the national broadcasters would
be permitted to broadcast non-commercial multi-channel programming in line with their charter
obligations.
Passage of this legislation was an attempt to appease competing stakeholders, but the actual situation is
summarised by Jock Given (Director of the Communications Law Centre at the University of NSW) in an
article published in one of Sydney’s morning newspapers:
…the commercial networks which get frequencies can't use them to provide multi-channel TV services,
because that would be competition for the Pay-TV business. And the new players which get
frequencies for datacasting can't use them for TV services, because that would be competition for the
free-to-air TV business. Policy is made by keeping the warring commercial interests equally unhappy,
rather than encouraging the creative exploration of the capabilities of a new and cost efficient
technology to provide a flexible and interesting service mix26.
The 1998 legislation specified that a number of reviews on future directions for digital television and
datacasting take place before 2000. The review process allowed competing stakeholders to lobby for
boundaries to be set on the digital system. The main changes of these reviews resulted in:
 broadcasters were able to offer digital enhancements to their main simulcast programmes if
these were directly linked to main channel programmes and broadcast as separate multi-channel
programmes ("multicasting" or "multiviewing"); and
 "triplecasting"; the telecast of the broadcaster’s analogue signal had to be broadcasting as a
standard definition digital signal at all times in addition to being broadcast in high definition for
at least 1040 hours per annum (of "native" content, not up-converted).
It has been argued by many commentators that these initial policy-driven technical limitations on the DTTB
system were an impediment to consumer uptake of digital television, but the initial availability of standard
definition receivers allowed the public its first experience of digital television.
25 Bills Digest No. 178 1997-98 Television Broadcasting Services (Digital Conversion) Bill 1998 www.aph.gov.au/
Parliamentary_Business/Bills_Legislation/bd/BD9798/98BD178
26
J Given, ‘Taking a punt with TV’, The Sydney Morning Herald, 26 March 1998, p. 19

23
2.3 Standards development
2.3.1 Transmission
In 1998 the Australian regulatory body for broadcasting, the Australian Broadcasting Authority,
in conjunction with the Australian national standards body, Standards Australia, and terrestrial televisions
broadcasters commenced development of a standard which specified the terrestrial television transmission
characteristics for Australia.
The BSA allows27
the regulator, the ACMA, by legislative instrument, to determine technical standards that
relate to digital television transmissions. Rather than legislate a technical standard, the regulator has used
its powers under s.33 of the BSA to make reference in the Technical Planning Guidelines to the transmission
standard developed in Standards Australia, Digital television – Terrestrial broadcasting Part 1:
Characteristics of digital terrestrial television transmissions AS4599.1-2007. The links between the BSA and
the standard is shown in Figure 4.
As indicated graphically in Figure 6, this standard builds on and references a suite of DVB standards
published as European Technical Standards Institute (ETSI) documents, but importantly makes special note
of variations required to suit the Australian legislated and technical environment. The standard was
structured in this manner to convey to manufacturers, who are mainly overseas companies, to highlight
how a standard DVB-T transmitter (and by inference a DVB-T receiver) could be readily adapted for
Australia. The standard also references a suite of Free TV Operational Practices. These are documents
developed by the broadcasters28
to provide common information or technical inputs into their broadcast
streams, for example parental guidance codes which meet the Code of Practice and are displayed in an
electronic programme guide, and are a further example of the co-regulatory nature of the Australian
broadcast system.
When published in 2000, AS4599 specified that while the DVB specifications and ETSI standards provide
a range of possible operations, the standard highlighted variations specific to Australian regulatory and
legislative requirements of most importance were:
 7 MHz channels were to be used both at VHF and UHF.
 Both 2K and 8K COFDM carrier operations could be expected.
 Transmissions could include video MPEG encoded at 25 frames, 50 fields and 50 frames per
second. The video could be scanned up to 1920 pixels by 1080 lines.
 Transmissions may include, at a minimum MPEG-1 Layer II sound, and potentially AC-3 sound
streams in either mono, stereo or stereo with surround, or an AC-3 sound stream with 5.1 channel
sound.
 Transmissions could include closed caption subtitles based on either or both ETSI standards
EN 300 473 and ETS 300 742.
 Transmissions may include data broadcasting as specified in EN 301 192.
 Transmission filter masks for Australia’s 7 MHz channel spacing would take into account the
relative proximity of lower adjacent channel dual analogue sound carriers compared with a less
stringent 8 MHz channel spacing.
27
s.130A of the BSA
28
Available at www.freetv.com.au/content_common/pg-engineering-guides.seo

24
Figure 6: AS4599.1 Structure
Source: Standards Australia and Free TV
2.3.2 Development of a DTTB reference transport stream
Australian terrestrial television broadcasters realised they were one of the first ‘horizontal’
implementations of DVB-T with no "cross carry" of service information between broadcaster multiplexes.
Within the ’vertical’ implementations of the DVB standards to date individual organisations and multiplex
operators had developed specifications for receivers and had a common source of service information. In
Australia there was the possibility in some licence areas services could be provided by at least
12 broadcasters, each with their own multiplex and a viewing audience supplied with receivers from a larger
number of sources.
Broadcasters developed a DTTB Reference Transport Stream for the testing of television receivers in a
broadcast environment simulating Australian conditions. The Streams were representative of the broadcast
signals to be provided at launch by Australian DTTB transmissions and specifications within the Australian
Standard AS4599. The video was presented in a variety of bit rates. The Service Information elements were
representative of a single location at a fixed point in time.
Two stream recordings were provided:
 File 1 – Australian DTTB Reference Transport Stream Ver 2-0 (19 Mbit/s) is a recording of 188 byte
packets at 19.352941 Mbit/s suitable for DVB-T 64-QAM with 2/3 FEC and a 1/8 guard interval.
 File 2 – Australian DTTB Reference Transport Stream Ver 2-0 (23 Mbit/s) is a recording of 188 byte
packets at 23.052768 Mbit/s suitable for DVB-T 64-QAM with 3/4 FEC and a 1/16 guard interval.
The features of the streams included:
 Source material of the highest video/audio quality prior to coding. SD material is 720 x 576i and
HD is 1920 x 1080i (50Hz). All aspect ratios are 16:9.
 Several services, up to two standard definition (SD) services and a high definition (HD) service.
The standard definition services comprise video, teletext closed captioning, Dolby AC-3 audio and
MPEG-1 Layer II audio components. The high definition service comprises video, Dolby AC-3 audio
and MPEG-1 Layer II audio components. The encode rates of each component are provided in the
mode table.

25
The streams incorporate extensive service information to test receivers for typical Australian DTTB
transmissions, including:
 The Network Information Table uses network identification codes assigned to Free TV and
included a complete channel list for the Australian state capital city markets. Each stream
incorporated a logical channel number (LCN) assignment as described in Free TV Operational
Practice OP-42 including multiple LCN assignments of a service.
 The Time Offset Table incorporated a typical summer to winter time change transition for
Australia as occurred in March 2001. It is important to note that Australia changes from three
time zones during winter months to five time zones in the summer.
 An extensive Event Information Table (EIT) was included for each service. There are three events,
with the first event repeated for the "next" information for the third event. The EIT exercises all
fields in the short_event_descriptor and the extended_event_descriptor. In addition,
content_descriptors and parental_rating_descriptors contained data as described in Free TV
Operational Practice OP-41 and in AS4599.
2.3.3 Reception
Broadcasters, receiver manufacturers, suppliers and the regulator have also worked together within
Standards Australia to develop other standards related to the digital broadcast system. These include Digital
television – Requirements for receivers Part 1: VHF/UHF DVB-T television AS4933.1. There was no regulated
basis for this standard, it provided guidance to overseas manufacturers as to what is required to receive
and decode DTTB in Australia.
Whilst the planning for DTTB is for fixed reception with rooftop antennas, many Australians live in home
units or apartments known as multi dwelling units (MDUs). In MDUs, the home owner may not own or have
direct access to the rooftop aerial, but signals are fed via a common distribution system, the system
characteristic of which may affect reception of free-to-air broadcast television. Broadcasters and industry
have also authored a standard Coaxial cable and optical fibre systems for the distribution of analogue and
digital television and sound signals in single and multiple dwelling installations AS/NZS 1367:2000 to specify
the requirements of these systems to pass DTTB signals in an acceptable manner.
Australian digital TV key initial factors
 DVB-T system selected.
 Broadcasters have own 7 MHz digital channel – no "cross carry" of service information to make a digital
platform.
 Digital transmitters located at the same sites to that of the analogue transmitters to provide same
coverage.
 Transmit Power 6 dB below analogue service.
 DTTB Service level defined by Field Strength values in rural, suburban and urban environments.
 "Triplecast" of programming simultaneously in analogue, SD and HD.
 1 January 2001 commencement in metropolitan areas, regional areas up to 3 years later, originally
anticipated to have an 8 year analogue / digital simulcast.
 Initial consumer proposition – better pictures (HD) and sound (up to 5.1 surround sound).
 Quota on HD TV broadcasts (1040 hours per annum).
 Local content and captioning requirements.
 Limits on multi-channels in return for prohibition on new commercial FTA entrants.

26
Part 3 – Implementation
3.1 Introduction
Implementation was a stage of the project that was led by broadcasters. Commencing a year prior to the
first DTTB transmissions, broadcasters sourced digital video encoders, multiplexers and other headend
equipment and purchased and installed digital transmitters. The first on-air tests were undertaken in August
2000, followed in September 2000 with transmissions in a very robust mode (with FEC R1/2) to try mobile
reception in demonstration tests co-incident with the staging of the Sydney 2000 Olympic Games.
3.2 Digital services
Initially multiplexes were launched with at least one SD video service and one HD video service. Some
services were accompanied by multiple audio services to provide MPEG-1 Layer 2 and Dolby AC-3 encoded
formats of the same content. Broadcasters who experimented with multiview services (multiple SD
channels) would undertake a mode change in their multiplex to remove the HD service to free up capacity
for the additional SD services. Table 4 summarises typical component bitrates in the multiplex when
services were launched.
Table 4: Initial multiplex component bit rates
Component Parameters Bitrate
Service Information (PSI/SI) ~250 kbit/s
HD Video MPEG-2 1440x1080i ~15 Mbit/s
SD Video MPEG-2 720x576i 5-6 Mbit/s
Teletext Lines 21 334 73 kbit/s
Stereo Audio MPEG-1 Layer II 256 kbit/s
Stereo Audio AC-3 Mode 2/0 256 kbit/s
Multi Channel Audio AC-3 Mode 5/1 448 kbit/s
In later years as government policy had changed to allow extra services and broadcasters had upgraded
their encoding and multiplexing equipment, subsequent technological developments allowed bitrates to be
reduced without sacrificing quality. Also, an effective capacity increase was created through the use of
statistical multiplexing, allowing higher peak encoding bitrates as the demands of each video service would
peak at different times due to different picture content. SD video rates typically now vary between 0.5 to
2 Mbit/s in a statistical multiplex for services with low movement video whereas premium channels are set
to operate between 2 to 6 Mbit/s. HD has been reduced to operate between 7 to 13 Mbit/s in a statistical
multiplex. In 2014, all video services still use MPEG-2 encoding. Audio components were rationalised and
reduced as receivers were able to adequately change between MPEG and AC-3 coded audio without
annoying audio spikes. A greater capacity of approximately 300 kbit/s (in addition to SI/PSI) is now
dedicated to the broadcast of electronic programme guide (EPG) data as there has been considerable
development over the years in EPG systems to provide better programme information to viewers.
3.3 Transmitter rollout
DVB-T formally commenced in Sydney, Melbourne, Brisbane, Adelaide and Perth on 1 January, 2001.
Initially services were planned to have an eight year simulcast with digital, regional areas were scheduled
three years later.

27
Commencement of a digital service involved a number of new workflows for a broadcaster:
 in Australia’s case, the vision aspect ratio changed from 4:3 to 16:9 which required the addition
of many aspect ratio converters to the broadcaster facility;
 the number of audio channels increased from stereo up to six channels of surround sound which
also required additional facilities;
 digital headends needed to be established to encode video and audio services and multiplex them
together with data in the form of service information and other ancillary data;
 establishing digital links between the broadcaster studios and transmitter site(s);
 installing transmitters;
 establishing translator facilities, often in a single frequency network.
The network structure is shown below in Figure 7. This figure should be compared to Figure 2 to highlight
the differences compared to the analogue network.
Figure 7: Australia terrestrial TV broadcast overview (Simulcast)
Source: ITU
3.3.1 Interference management scheme
Commencing a new radio frequency transmission carries the risk of creating interference to existing
services. This was particularly the case with the broadcasting services bands used for television as the
implementation of DTTB was to fill in between the analogue services. Although the tests and planning had
indicated that this was possible to do, the statistical nature of field strength as it varies in response to
natural phenomena, can create unexpected results.
For broadcasters, in particular commercial broadcasters, any loss of audience possibly translates into a loss
of revenue, so they are particularly careful to avoid or readily quantify and correct any interference.
Broadcasters and the regulator devised a scheme to manage the process of commencing a new DTTB
service and managing any interference complaints that arose. This process was legislated as Part 7 of the
Technical Planning Guidelines Interference Management Scheme for digital television.

28
(i) Interference management process
Broadcasters, through their industry body, the Federation of Australian Commercial Television Stations
(FACTS – now Free TV Australia) coordinated all aspects related to the administration of the process.
The key elements of the process were:
 development of a brochure delivered to residents. The brochures outlined types of interference
and re-tuning information;
 the establishment of an interference hotline (the hotline) for all Australian States. This toll-free
number provided advice to viewers on re-tuning arrangements, and provided access to
technicians where required; and
 a media campaign, which included advertisements in local and national newspapers and on local
television stations.
(ii) Bringing a new transmitter into service
To commence a new transmission:
 at least seven days before commencing, the broadcaster had to notify nominated organisations
including other broadcasters in the same and adjacent licence areas, the regulator and make
public notices in an area up to 200 km from the transmitter site (the distance depended on the
transmitted power);
 transmissions generally commenced 10dB below their nominated power and were brought up to
nominated levels over a few days, during this period;
 broadcaster obligations regarding receiving and handling complaints were handled by the
industry interference management scheme hotline (see below). These obligations lasted for
12 months after the service commenced.
The telephone hotline was for the public to make complaints. Broadcasters jointly funded this operation
and contracted a commercial call centre to undertake the work. Based information from the caller, either
standard advice was provided by the call centre to resolve the complaint or for more difficult cases an
installation company was contracted to visit the complainant’s home and undertake corrective work.
An escalation procedure was included to allow for cases where the complaint levels were above a pre-
determined threshold, obliging the broadcaster to promptly resolve the complaints by various means
including as a last resort, lowering transmitter power. This accommodated the political objective of
resolving what would otherwise be complaints to a local member of the federal parliament.
(iii) Technical resolution of complaints
Investigation of the problems reported by the public revealed the following common problems:
 VHF antenna bandwidth; in the major metropolitan cities, VHF Band III analogue channels were
7, 9 and 10. DTTB were established on channels 6, 8, 11 and 12. Reports of no reception of mainly
channels 12, 11 and 6 (in that order) revealed that some antennas had been designed with
a narrower bandwidth to increase the gain and so had a lower gain and bad gain – scope across
the outer channels. Replacement with a new antenna designed for all services resolved these
complaints.
 Antenna maintenance; roof mounted antennas are open to the elements and deteriorate over
time, but a householder’s priority to maintain their antenna is very low. Whereas the viewer
would suffer a grade 3 analogue signal, the "cliff effect" of digital made viewing unwatchable and
highlighted the need for maintenance or a new antenna.

29
 Masthead overload; adding the digital signals, although at lower powers than analogue
(but the crest factor of digital signals must be considered) increase the loading on installations
with an amplifier in the ceiling to amplify the signal before splitting and distribution in a
household. Reducing the gain of the amplifier (many are adjustable) resolved the problem.
 Similarly, some viewers near the transmitter sites had signal levels into their receivers that were
too high. A commonly misunderstood concept is that higher signal levels are worse, not better
for digital. Generally an in-line attenuator solved the issue.
 In some cases differing signal levels between services caused problems and were generally solved
by installing filters. However, these needed to be removed when digital services were later
restacked.
3.3.2 Development of DVB service information
In an analogue television broadcasting system, channel selection is based on tuning to a new frequency and
then demodulating the signals in that channel.
A digital television system operates in a completely different manner. The concept of channel selection
does not exist, replaced by a service selection concept which is organised by data in the digital multiplex
called Service Information. This information is organised into a number of tables of key parameters to
identify a service; the original_network_id (ONID), transport stream_id (TSID) and service_id (SID)
(often referred to as the "DVB triple"). A DVB digital television receiver generally scans all available channels
to discover digital carriers, demodulates them and discovers this service information then stores the result
in memory to later "tune" the television to the desired service by the viewer.
As indicated in Section 1.6.5, this level of information in the broadcast transport streams is managed by the
industry operational practices. Free TV Operational Practice OP-40 assigns ranges of values of ONIDs, TSIDs
and SIDs for each broadcaster in each licence area. To make the discovery of services more viewer-friendly,
Free TV Operational Practice OP-41 lists values of a logical_channel_descriptor (LCN) so that a reasonable
service number is presented to the viewer while the receiver actually works on the DVB triple in
the background.
(i) The concept of service information (SI) interference
In an analogue system, interference occurs in the radio frequency domain; e.g. a distant transmitter on the
same channel being received at a low level compare to the desired local channel and the result is a degraded
picture and sound quality.
In a digital system, clashes in the service information allows one operator to "capture" the intended viewer
selection of another service. Depending on the order in which a receiver scans each channel and stores the
"DVB triple" information, a competitor could add some data into their digital stream to mimick the
competitor’s service, but point to their own video and audio components, so the viewer would never
actually see their intended service, but have two instances of the competitor’s service! This is the concept
of service information interference.
In Australia’s digital system each broadcaster has their own 7 MHz channel and they organise their own
service information in their digital streams. Historically this is a result of the fiercely competitive nature of
Australian commercial broadcasters who dislike having any part of their business influenced by their
competitors. A practical reason emerged as the impacts of digital grew – broadcasters were able to
aggregate their presentation systems to gain an operational cost reduction. Not all broadcasters aggregated
their presentation facilities in the same location. For example, digital television services for Cairns in North
Queensland are generated in Sydney (2 broadcasters), Canberra, Wollongong and Melbourne. The nearest
headend is 2 000 km from the licence area and the headends are over 700 km apart, which would require
considerable very expensive linking to aggregate services in one location. Hence with separate multiplex
locations and separate generation of SI, clashes are avoided by following the allocations of the broadcast
industry operational practices.

30
Other Administrations have DTTB systems where there is a single country multiplex operator, broadcaster
content is delivered to the multiplex operator for encoding, multiplexing and transmission. The multiplex
operator ensures the same SI is in each digital stream, referred to a ‘cross carry’ of SI. In this instance the
multiplex operator is the sole controller of service information in the stream so they ensure there are no
clashes in allocation of SI.
(ii) Adapting to local requirements
Other operational practices have been developed to cater for local requirements:
 Without any ‘cross carry’ of SI, the Australian system has had to develop methods of building
electronic service guides.
 An operational practice regarding time zones and daylight saving changes was created to cater
for the different manner in which Australian states change to daylight saving. It is worth noting
that as the DVB system is European-based, Australia had to make submissions to change their
system to cater for time zones on the other side of the world! The important lesson here is each
Administration needs to examine the specifications and standard in fine detail to ensure they
cater for local circumstances.
 For example an operational practice was developed to assist viewers move from HD content when
it was broadcast back to the SD service at the conclusion. However, this was not a success as
receivers reacted differently to the SI standard.
3.4 Consumer take-up
At commencement, limitations were placed on what broadcasters could do in their digital transmissions,
limiting the flexibility and innovation available in a digital system. At the time, digital set-top receivers were
considered expensive and widescreen displays were still based on analogue technologies, but there was
considerable product development undertaken in display technologies commencing with cathode ray tubes
(CRT) whose size was ultimately limited by the strength of glass in the screen, rear projection systems which
enabled larger displays but suffered from optical alignment issues to plasma displays which were digital in
nature and of high quality and finally to liquid crystal displays (LCD) which have ultimately been embraced
by consumers and accelerated digital take up in homes.
Reasonably priced quality integrated LCD and plasma televisions appeared in the market circa 2006 and this
was a major driver of take up of HD capable receivers. Figure 8: Consumer conversion to digital television
is an aggregation of different data sources to show the growth in digital television into Australian
households. The early data is sourced from Digital Broadcasting Australia (DBA) an industry organisation
formed in the early years of digital broadcasting in Australia. At the time, no organisation was surveying
households to assess take up of digital television, DBA initiated action by seeking sales figures from DBA
members. In 2005 this task was undertaken on a more formal basis by others and continued through until
2009 when the government Digital Switchover Taskforce (DSTF) commissioned the Digital Tracker surveys
of households29
. It must be noted that the figures prior to June, 2009 are based on sales of televisions,
whereas the Digital Tracker is based on households so the two sets of data are not measuring the same
entity. The sales figures have been scaled by assumptions related to estimates of second and other sets in
a household and replacement sales for failed units or consumer upgrades, in an attempt to convert sales
into households. The only reference point between the two sets of data is the ACMA surveys of DTTB
household penetration undertaken on an irregular basis between 2005 and 2007, which provides
reasonable correlation to the total estimated households. The BuddeComm estimates30
are based on the
same industry data, but are shown as estimates for 2008 and 2009.
29
Data extracted from reports available at www.communications.gov.au/television/digital_tv_in_australia/
digital_switchover_reports
30
Box 7 Dr Rhonda Jolly, Going digital: tracing the transition to digital terrestrial television in Australia, RESEARCH PAPER
No. 7, 2010-11, 19 November 2010, Parliament of Australia Parliamentary Library

31
However, the sales-based data provided a key indicator in the earlier years – that of the split between SD
and HD capable receivers, showing the tipping point occurring in early 2008 when sales of HD receivers
exceeded SD receivers and the trend can be seen from about a year earlier. Within a few months, household
penetration reached 50 per cent, this was the point at which Australia changed from being a nation with an
analogue broadcast system and sampling digital services, to a nation with a digital broadcast system
needing the remaining households to convert.
Although the Digital Tracker surveys peak at approximately 95 per cent conversion, the final numbers are
much closer to 100 per cent when considering the effect of last minute conversions by the government
assistance programmes and ‘laggard’ viewers converting. Post switchover surveys in each switchover region
indicated between 98 and 99 per cent of households could watch digital television.
Figure 8: Consumer conversion to digital television in Australia
Source: www.communications.gov.au/television/digital_tv_in_australia/digital_switchover_reports and Digital
Broadcasting Australia
3.5 Viewer complaints
For a period of approximately six years there were no dramatic changes in television broadcasting policy,
so from a technical perspective it was a stable period which allowed broadcasters to test various aspects of
the digital system and for engineers to focus on refinement of the transmission network. Digital take up by
consumers provided a better statistical base for viewer complaints so reception issues could
be investigated.
Unexpected problems were highlighted by analysis of reports from the Interference Management Scheme.
As resources permitted, broadcast engineers would visit areas and make detailed field strength surveys to
observe actual conditions and then analyse those results against the predictive models used in planning.
This allowed broadcast engineers a better understanding of the "cliff effect" of digital signals related to
terrain and foliage clutter in varying weather conditions.

32
(i) The "Cliff Effect" of digital reception
Figure 9 shows the digital quality scale as a graphical representation of the second line of Table 1 in ITU-R
Recommendation BT.1735-2. Although shown as a wide range, in practice, the width of the Q2 scale is
approximately 1 to 1.5 dB of variation in field strength which is the point where a DVB-T demodulator
changes from Quasi Error Free (QEF) reception (providing near imperceptible video and audio) to the Signal
Failure Point (SFP). Overlaid on this graph is an example of the slower degradation with reducing field
strength reception of analogue signals, coloured in accordance with the ITU-R quality and impairment scales
of Table 3 of ITU-R Recommendation BT.500-13. It is important to note that the analogue and digital quality
scales are not directly related to each other, they are two scales aiming to provide an assessment of the
different methods of transmission.
During the simulcast period, anecdotal evidence was provided by viewers that when the digital service
began to suffer break up, they would change back to the analogue service to continue their viewing and
suffer the worse picture quality, but they could follow the story as the sound was still intelligible.
Conversely, viewers who had good, reliable digital reception are represented by the shaded area in Figure 9
and enjoy better pictures and sound than they would have with analogue reception. The future of a reliable
widespread digital service is for the planning and broadcast engineers to ensure that as many people as
possible have reception equating to the blue shaded area.
Figure 9: The "Cliff Effect" of digital reception
Source: ITU
In many cases, viewers complained they normally had reliable digital reception, but only at times
(which seemed to correspond to broadcast times for their favourite programmes!) the reception would
suddenly degrade. Generally issues identified were:
 The viewer’s reception or antenna system was marginal so their normal conditions provided
excellent digital reception, but any change such as weather conditions reduced the signal to the
"cliff effect" region and so reception suddenly became unwatchable.
 The effect of local clutter such as vegetation draws on the margins in the reception system.
This was demonstrated often by viewers complaining that their reception degraded when the
receiving antenna was pointed towards trees nearby and although not quantified, the water
vapour in the leaves, or during or immediately after wet weather, would degrade reception. Often
these cases were corrected by removing the offending vegetation, or if this was not possible,

33
relocating the antenna. This problem was investigated in depth by one of the national
broadcasters following up on complaints in Darwin which is in the tropical north of Australia. In
summary, the conclusion was wet palm fronds were affecting reception. Darwin is a very flat
environment so there was not a great clearance above the ground to most households in the
licence area.
 Investigations at Brooklyn north of Sydney demonstrated the combined effect of varying knife
edge diffraction of signals and the different effective pattern of a transmit antenna over a wide
frequency range. Brooklyn is located in a deep valley of the Hawkesbury River so they cannot
receive transmissions from the main Sydney transmitters. A translator site at Bouddi is located
on the coastline near where the Hawkesbury River meets the ocean. Even in the direction to
Bouddi the radio propagation path is blocked by other hills, but there is much less blockage than
to Sydney, so over the years installed antennas pointed to Bouddi. The analogue channels
assigned were low UHF Band IV for national broadcasters and high UHF Band V for commercial
broadcasters. Digital allocations were opposite – low UHF Band IV for commercial broadcasters
and high UHF Band V for national broadcasters. Investigations in the local area soon revealed that
viewers were watching national services in analogue and commercial services in digital. The extra
knife edge diffraction and slight change in radiation pattern across the band resulted in the high
UHF Band V services being 7dB lower than the low UHF Band IV services. In an area which had
marginal reception, the 7 dB made the services unusable. It was, however an interesting
consideration into the future restack of digital services to remove these factors by placing all
services on adjacent channels and reducing the frequency spread.
(ii) Single Frequency Networks (SFNs)
The other category of reception problems related to the implementation of SFNs. Transmitters operating
in an SFN have to be locked so that the same information is broadcast on the same frequency at precisely
the same time. If any one of these three factors changes, the transmitters fail to offer continuous coverage
and become interferers with each other. Failure of a transmitter or its GPS timing reference has to be readily
identified and corrected as the level of interference goes far beyond the coverage area of the transmitter.
The co-channel protection ratio varies depending on the modulation parameters, but in Australia’s case,
if the carrier-to-noise ratio is less than 20 dB reception problems will be experienced. Hence if all
transmitters in an SFN are producing the same field strength, the interference boundary would exist a
further 20 dB away which could be several kilometres, so reception over a very wide area is affected.
The relative timing of transmitters in an SFN has to be planned to avoid "mush zones" where the signals
arrive at the receive antenna at the same time and are about the same level. Australian experience is that
many receivers encountering these conditions are not able to decide which impulse to lock onto as the
reference in the SFN network, so as they change (effectively between locking to different transmitters in
the SFN) they have a corrupted data output which manifests as momentary blocking or picture breakup. It
is best for the network planner to try and delay the launching of signals from one transmitter so the areas
where same receive level / same time does not coincide with populated areas. For example two translators
at North Head and Kings Cross in Sydney operate in an SFN and the timing was adjusted such that the signals
arrive at the same time in Sydney Harbour, where a "mush zone" is created rather than across the
harbourside suburbs.
The "mush zone" issue may be partially resolved by careful location of receive antennas to employ the
front-to-back ratio of the antenna as a discriminator between the transmitters in the SFN. This technique
has also been used when additional sites were required but no additional frequencies were available,
resulting in the design of an SFN which transmit outside of the guard interval timing as the distance between
transmit sites was too large. In this case a large zone was created where the signals arrived outside of the
guard interval, so the transmitters would interfere. However, by using the front-to-back ratio of the
receiving antenna to expand the differences in effective receive level from the wanted and unwanted
transmitters, the receivers "saw" sufficient co-channel protection ratio and had a decodable carrier to noise
ratio.

34
However, due to the constraints of channel planning within the simulcast period, some broadcasters had
to use SFNs based on a different set of transmit sites to other broadcasters. When the viewer installs their
antenna towards one of the sites in the SFN, this would often mean other wanted broadcaster signals were
mainly coming in from an adjacent transmitter site, so the discriminatory nature of the antenna was non-
optimal for the adjacent site and reception problems arose. This could be solved by installing a second
antenna and extensive filtering, but the viewer tended to just go without the service or drop back to
analogue. This was another consideration for the future restack of digital services to ensure all broadcaster
SFNs were from the same sites.
3.6 Receivers
Whereas many aspects of free-to-air television are highly regulated by government, Australia has a free
unregulated market for supply of television receivers. Many consumer electronics manufacturers saw
business opportunities in Australia so a wide variety of receivers were available. The software design of
each receiver had its own idiosyncrasies which often led to viewer complaints that were resolved by
attention to fine detail in service information or close collaboration with manufacturer’s design teams.
The different receiver reactions and consequent potential loss of audience if a broadcaster implemented
some of the more esoteric service information features of DVB discouraged broadcasters to innovate and
offer new services.
Later systems implemented by broadcasters such as the addition of a common MHEG-based electronic
programme guide or the subsequent Hybrid Broadband Broadcast television (hbbTV) systems have insisted
on accreditation and testing schemes to overcome these types of issues.
3.7 Government reviews
Between 2004 and early 2006, the Department of Communications, Information Technology and the Arts
(DCITA) conducted a series of reviews on various aspects of digital television broadcasting including
restrictions on additional programming, the moratorium on new broadcast licences, the allocation of
spectrum, underserved television markets, high definition requirements and the duration of simulcast.
The only notable outcome from these reviews was an acknowledgement that HDTV was becoming more
popular with the public.
The lower house in the Australian Parliament, the House of Representatives, held an enquiry shortly
afterwards in 2006 at which point multi-channelling became a prominent issue.
The Government followed these reviews with a Media Reform Package, including the following digital
changes :
 removed genre restrictions previously imposed on the ABC and SBS multi channels;
 allowed commercial television licensees to provide a non-simulcast HD channel from 1 January
2007, a standard definition multi channel from 1 January 2009 and any number of multi channels
at the conclusion of the simulcast period;
 removed the HDTV quota at the end of the simulcast period; and
 provided that content requirements on multi channels should not be ‘overly onerous’.
To implement these policy changes, the Broadcasting Legislation Amendment (Digital Television) Act 2006
was enacted which made changes to the BSA and RCA.
The effect of these changes was to allow broadcasters to offer more programming and so begin to allow
the capabilities of a digital system to be enjoyed by the public, which provided further impetus to digital
conversion of households.

35
3.8 Digital Australia
As part of the Media Reform Package, the government established Digital Australia – a dedicated digital
switchover body within the Department of Communications, Information Technology and the Arts to
coordinate and oversee Australia’s transition to digital31
.
The government stated aim in establishing Digital Australia was to provide a clear focal point for all
Australians wanting to know more about digital switchover, when it is occurring and how it is being
managed, with the following objectives:
 educate Australians on the benefits of digital television in order to accelerate take-up and inform
consumers about the need to convert to digital transmission as switchover approaches;
 identify sections of the community which may have special needs and co-ordinate efforts to meet
those needs;
 harness the expertise and co-ordinate the diverse interests of industry in the switchover process –
broadcasters, receiver importers, antenna installers and retailers will all be called upon to
participate; and
 work closely with government and the regulator (ACMA) to ensure Australia is able to commence
switchover in 2010-2012.
The government also established an Industry Advisory Group comprising broadcasters, manufacturers,
retailers, antenna technicians and consumer representatives to advise and liaise with Digital Australia in
implementing its Digital Action Plan.
In establishing Digital Australia and the Digital Action Plan, the government began the process of setting
the timetable for the end of analogue broadcasting.
Australian digital TV implementation lessons
 Establishing detailed transmission and receiver standards for harmonisation of international standards
with local conditions is a foundation to the success of the transition.
 Careful establishment of digital services is essential to avoid interruption to existing services.
 A well-managed and resourced Interference Management Scheme is essential.
 The need for viewers to upgrade or maintain their reception equipment should not be overlooked to
achieve good digital reception.
 Available reasonably priced receiving equipment will drive market take up.
 Government should undertake regular surveys to quantify the success of the take up.
 Variability in reception should not be overlooked to avoid viewers operating near the digital cliff.
 Make sufficient allowances in the planning for local clutter.
 When planning channel assignments, avoid a wide spread of channels to serve a particular area.
 Single Frequency Networks are good for efficient use of spectrum, but care needs to be taken to the
design of the network in the SFN.
 All services should have the same SFN characteristics.
 In a free consumer market, receiver testing must be encouraged in some manner to generate conformity
and allow the digital system to be fully utilised.
 Policy settings should be carefully considered to assist in driving market take up.
31
Australia Government, DCITA, READY, SET, GO DIGITAL A Digital Action Plan for Australia, November 2006 Page 13

36
Part 4 – Digital enhancement
4.1 Introduction
Despite the take up actually accelerating due to the changes in display technology and lowering consumer
prices, public debate over the take up of digital, there was pressure from telecommunication interests to
secure spectrum from the "digital dividend". The election of a new government in November 2007 then
announced on 19 December 2007 that analogue would be switched off at the end of 2013 and a new Digital
Switchover Taskforce established (see Section 5.2) within the newly named Department of Broadband,
Communications and the Digital Economy, with the aim of hastening the switch off of analogue broadcasts
and release of broadcasting spectrum for other services.
Reliable, quality digital coverage is vital to broadcasters as that is their only means of accessing viewers in
the future. With the pending closure of the analogue service in sight, broadcasters commenced an intensive
review of digital coverage. In Stage 2, "same coverage" was essentially achieved by installing digital
transmitters at the existing analogue broadcasting sites and operating at powers 6 dB lower than analogue.
However, garnering the experience gained in Stage 2 from investigating viewer reception complaints and
undertaking extensive field surveys, each licence area was reviewed to investigate methods of cost-
effectively enhancing coverage in areas where the digital service was proving to not be completely reliable.
The investigation and planning stage for these new sites took approximately three years to complete and
installation the following three to four years. This stage had to be completed prior to analogue switch off
so that viewers did not lose coverage during the changeover.
4.2 Review of underserved areas
Broadcasters commissioned an engineering review of underserved areas. The review included interviewing
local staff from each network station to gather all the local information regarding poorly served areas. The
study looked at over 300 locations across the country and performed an initial evaluation, categorising sites
into:
 sites where new "gap filler" translators would be required;
 existing sites that might be modified to provide coverage;
 locations that needed further study;
 areas where a community information campaign would be appropriate (for example to use an
existing digital service);
 areas that should be served by a new "gap filler" but would be commercially unviable;
 areas where upgrading an existing community self help facility;
 areas where no solution could be found;
 areas where no action is required.
The review also encompassed nearly 200 community self-help sites, which had been installed over many
years as part of a government funded programme to assist underserved communities. These facilities were
operated and maintained by local authorities and only provided analogue television transmissions.
In the review, broadcasters proposed to:
 convert nearly 50 per cent of the sites to digital transmission;
 not convert nearly 25 per cent of the sites as they would be covered by other digital transmission
facilities, in particular there were a number of sites installed to solve local analogue ghosting
issues so these were not needed in digital;

37
 not convert 25 per cent of the sites as they would be better served by the VAST system (see next
section);
 not convert a few sites as commercial services were not broadcast from those sites.
(i) Gap filler planning
What followed was probably the most intense period of broadcast planning undertaken in Australia. Every
licence area was analysed and propagation predictions undertaken simultaneously by metropolitan and
regional broadcast engineers and the results then discussed with the ACMA engineering staff and re-
analysed using their propagation software. All three groups used software models from different companies
and different ITU-R propagation models were used. Comparison of the results and comparison to
measurement data undertaken by the ACMA increased the confidence level in the resulting predictions.
For broadcasters, this represented the last opportunity to establish sites to provide reliable network
coverage into the future. Hence, the planning also needed to take into account predictions on future events
such as geographic population growth, so special attention was paid to developing growth areas to make
sure they were covered, or a plan devised to include coverage in the future. Consideration was given to the
problems that had been reported by viewers.
 In the metropolitan licence areas new growth areas needed coverage and a major issue is the
increasing density of development which often includes new high rise buildings or even large
blocks of units which effectively shade their neighbours of television signals. The solution to these
issues was to find new sites in each city to primarily cover the underserved or growth areas, but
as a secondary consideration have their wider coverage as an alternative for households who may
suffer "building clutter" in the direction of their primary site in the future. Of course, this still
needed to be achieved in a spectrally efficient manner, so particular attention was given to
antenna patterns and SFN design.
 In the regional licence areas, new towns had been established which needed coverage, also the
main issue reported by viewers related to having sufficient field strength to pass through areas
of vegetation, particularly along riverbanks where otherwise Australia may be considered as an
arid area, but rural settlements mainly were established near the only water source and available
transport routes, the rivers.
During discussions with the regulator, the ACMA, regarding the planned coverage of these gap filler sites,
the ACMA requested that the target service areas for each gap filler be defined by the suburban grade
contour even when the target environment was of a rural nature. As is noted in Section 02.1.5, only the
rural field strength is used as the definition of whether a broadcaster is serving their licence area correctly,
so this was a change of technical policy and no formal written explanation has been provided by the
regulator. However, broadcasters were generally in agreement with this change as providing a higher field
strength meant better coverage. What was later evident once restack planning had been completed was
that the regulator was pre-empting the need to have higher field strengths as frequency re-use planning
rules needed to be breached (and hence creating interference between transmitter service areas where
the wanted transmitter signal strength is low) in order to provide services in constrained bands one the
digital dividend had been removed from broadcasting use. Previously a concept of ‘fortuitous coverage’
prevailed where viewers were able to receive distant transmissions where the received signal carrier / noise
was only limited by electrical noise, not licenced for their location. The restack changed the unwritten
model in some areas from a "noise limited" model to an "interference limited" model.
The final outcome of this review necessitated the eventual establishment of 34 new digital sites in the major
metropolitan areas of Sydney, Melbourne, Brisbane, Adelaide and Perth and 85 new digital sites in regional
licence areas, including the conversion of many self-help community broadcast sites. In addition, a number
of existing sites were upgraded by either having larger transmitters installed, or the transmit antenna
patterns changed to serve new areas which had been developed since the site was first established.

38
When these additional gap filling sites were established, there were still in operation the main digital and
analogue services, so special attention was given to planning spectrum for these sites as the broadcasting
spectrum was already heavily congested. When these services commenced, the broadcasting services
bands spectrum was at its highest utilisation. In fact there was no spectrum left for the conversion of the
smaller self-help community sites, so they had to be turned off and turned on in digital mode on the same
day. Other sites were integrated into single frequency networks with existing digital sites to make better
use of existing spectrum.
Some of the planning and implementation of this stage was conducted in parallel with planning the
analogue switch off and restack planning (see Part 5 and Part 6 below). In some remote areas, these Stages
of the overall project merged to the point where sites were installed on their restacked channel
assignments, rather than be installed and have to be subsequently retuned. When to planning commenced,
the scale of the digital dividend was unknown.
(ii) Public information campaign
Although broadcasters were driving the programme of installation and commissioning new gap filler
transmission sites, no public information campaign was undertaken at the time these sites commenced
operation. At the time, the public information campaigns conducted by government in relation to analogue
switch off and restack were underway, it was thought that any other campaign might confuse the issues for
the public. The necessary information was passed to the government who integrated key messages into
their systems.
(iii) Coverage working group
Co-incident with the work on gap fillers, the broadcasters established a forum with the regulator to jointly
work on deeper investigation of digital coverage issues. The Technical Working Group on Coverage was a
collection of experts from each broadcaster and the ACMA planning group and undertook review of
reception reports and measurement techniques. Many Australian contributions to ITU-R Working Party 6A
emanated from this group including the formative work that has led to Recommendations on field survey
techniques, objective reception quality assessment of DVB-T and the effects of wind farms on reception of
DVB-T.
4.3 Black spot and satellite solutions
Simultaneously with the broadcaster engineering review, the government was receiving complaints about
‘black spots’32
for digital television reception. The government was keen to release a switch off timetable,
highlighting the need to devise solutions for these sites as well as the community self-help sites previously
funded by the government, but operating as analogue transmission sites outside of the control of,
or management by broadcasters.
Negotiations between commercial broadcasters and government saw the commercial broadcasters take on
responsibility for converting and maintaining the self-help facilities, including funding translators for the
national networks (national networks are normally funded by the government), while the government
committed to delivering a free-to-air satellite service to provide digital television transmission to over a
quarter of a million households which would be unable to access services from terrestrial transmitters33
.
Subsequently in April 2010, the government announced that an agreement had been reached to establish
a joint venture company, Viewer Access Satellite Television (VAST), to deliver the satellite service.
32 In Australia, areas where reception of television is unsatisfactory are called television signal “black spots”.
33
S Conroy (Minister for Broadband, Communications and the Digital Economy), Digital television Australia-wide, media
release, 11 January 2010

39
In addition to its primary role of providing television to remote areas, the VAST service is the ‘catch all’
service to serve isolated areas in metropolitan and regional licence areas that do not have acceptable digital
terrestrial broadcasting. The service within a licence area must be by agreement of the licenced
broadcasters in that area. The service is used in some instances as the feeder link to some isolated
communities who have established their own terrestrial digital transmitters.
It is a testament to the level of planning that despite the difficult terrain to cover terrestrially, number of
VAST activations in metropolitan licence areas remains very low. At the end of May 2014, Brisbane had
0.6 per cent of households activated whereas all other metropolitan markets were less than 0.3 per cent,
implying that either 99.4 per cent (Brisbane) or 99.7 per cent (others) of households receive their television
terrestrially or via subscription platforms. In regional licence areas VAST activations remain below
2 per cent of households so 98 per cent of these large licence areas are covered by terrestrial television.
Australian digital TV enhancement lessons
 Before commencing analogue switch off, it is important to thoroughly review digital coverage to ensure
underserved areas are rectified, changes in population patterns have been accommodated and coverage
is planned for the future.
 Minimum signal levels used in coverage planning need to be reviewed to be consistent with changed
spectrum arrangements.

40
Part 5 – Analogue switch off
5.1 Introduction
Switching off a service is a relatively simple task. However, planning to ensure that the viewing public will
not be impacted by the switch is complex. The government established a task force to plan the switch off
of analogue services. This group had to liaise widely with broadcasters and other industry segments to
ensure that all facilities were in place in preparation for the switch off. Government and broadcasters had
a shared outcome, broadcasters wanted to know that they would not suffer a loss of audience on switch
off, for government this audience represents the voting public so they wanted to ensure they were not
affected by the switch.
5.2 Digital switchover taskforce
In December 2007, the newly elected government replaced Digital Australia by establishing a Digital
Switchover Taskforce (DSTF) to coordinate and oversee the transition to digital from analogue television.
Its objectives are to:
– advise government on policy settings, implementation and issues connected with digital
switchover;
– develop and implement a programme framework, including a switchover timetable, to complete
the switchover from analogue to digital television transmission in Australia by the end of 2013;
– manage an information and education programme explaining the switchover process to all
Australians setting out what they will need to do and how to get further information; and
– convene meetings of an industry advisory group consisting of stakeholders – including
broadcasters, retailers, manufacturers, antenna technicians and public and commercial housing
agencies, government departments – and coordinate these to utilize their expertise in delivering
switchover by the end of 2013.
5.2.1 Industry advisory group and working groups
In establishing the Industry Advisory Group and its working groups, the DSTF became the focal point for all
activities related to analogue switch off. The DSTF established several working groups, including:
 Transmission and Spectrum Working Group: comprising representatives of each broadcaster, the
Department and the ACMA.
 Satellite Implementation Working Group: comprising broadcasters who were involved in the
satellite proposal for remote areas, the Department and the ACMA.
 Housing, Building and MDU Working Group: comprising representatives of some broadcasters,
public and commercial housing agencies, antenna installer industry representatives and
manufacturers.
 Supply Chain Working Group: comprising representatives of manufacturers and their industry
associations.
5.2.2 Government assistance schemes
The government had developed two assistance schemes to convert disadvantaged groups within the
community; the Household Assistance Scheme (HAS) and Satellite Subsidy Scheme (SSS).

41
(i) Household Assistance Scheme
The Household Assistance Scheme 34
provided free help for eligible people to switch to digital TV.
The assistance package included (free of charge)
 one high definition set-top box;
 installation and demonstration of the new equipment by a technician;
 if the eligible person owned their home, any necessary upgrades to your cabling external antenna
or satellite systems;
 12 months equipment warranty, free support and service.
Eligibility was based on receiving at the full rate one of the following government benefits:
 age pension;
 disability support pension;
 carer payment;
 veterans’ affairs service pension;
 veterans’ affairs income support supplement;
as long as the householder did not already have access to digital television.
(ii) Satellite Subsidy Scheme
This scheme35 provided assistance to households that moved to the VAST satellite service as part of the
switchover to digital TV and that previously relied on community-operated ‘self help’ analogue transmitters.
The scheme closed on 10 January, 2014.
The scheme provided a subsidy for part of the cost of installation of VAST satellite TV equipment (including
a satellite dish, a VAST-enabled set-top box and associated cabling) in households by qualified installers
contracted by the Australia Government and who have experience in satellite dish installation. The subsidy
of between AUD 200 and AUD 250 depending on location was paid directly to the installer, reducing the
cost to the householder. In remote Indigenous communities, full assistance was provided without a
household contribution being required.
A 12-month warranty on equipment and installation was also provided.
(iii) Resource allocation and publicity
From the government perspective, there was a need to coordinate the roll out of gap fillers and self help
conversions in a way which is effectively integrated with the government assistance programmes. The HAS
was scheduled to occur at or shortly after commencement of new digital services. In addition, the Satellite
Subsidy Scheme (SSS) will be established for those self-help sites that are not confirmed for digital upgrade.
There were significant lead times involved in preparing and delivering these assistance programmes. Each
involves engaging contractors to deliver services in an area and communicating with viewers so that they
can opt-in to services from six months before switchover.
34
HAS Brochure, Digital Switchover Taskforce, November 2011 retrieved via
www.headwaytas.net.au/attachments/article/145/HAS%20brochure.pdf
35 Satellite Subsidy Scheme, Digital Switchover Taskforce, December, 2011 retrieved from the Byron Shire Council website
www.byron.nsw.gov.au/

42
Hence, at the meetings of the Transmission and Spectrum Working Group, the installation progress of each
new digital sites was reviewed in detail to allow for Scheme resources to be scheduled as well as publicity
campaigns engaged at the appropriate time. The Transmission and Spectrum Working Group met on a
monthly basis from early 2010 until the end of analogue switch off in December 2013 to review the rollout.
5.2.3 Digital tracker
The DSTF commissioned the Digital Tracker surveys of households measuring the national uptake of digital
TV and Australians' awareness and attitudes towards the switchover to digital TV36
. The Digital Tracker
measured and reported on the following five critical success measures to provide an indication of Australia’s
digital readiness:
1. Awareness (heard of switchover)
2. Understanding (knew how to convert to digital TV)
3. Attitudes (positive or negative to switchover)
4. Conversion (had converted main TV set to digital)
5. Satisfaction (with digital TV)
After an extensive development and testing phase in 2008, the first quarterly Digital Tracker was conducted
in January to March 2009 with 9 900 respondents. The scope of the survey was all Australian households
and interviews were conducted by telephone. The sample design was a random survey stratified by
the 33 switchover areas.
Surveys were taken each quarter up until all regions had switched off the analogue service. A post switch
off survey was undertaken in each region to gauge the final success of the programme.
The key result of household conversion from each survey has been included in Figure 8 in Section 3.4.
5.2.4 Publicity and labelling scheme
The government launched a campaign to improve digital television uptake in April 2009. The campaign was
organised by the DSTF and featured television, radio and online advertisements, a Get Ready for Digital
website www.digitalready.gov.au, point-of-sale information and training and accreditation for retail staff.
In conjunction with manufacturers and importer of receivers, a labelling scheme for televisions was also
launched to identify receivers in three categories as shown in Figure 10:
1. Digital TV Capable – for analogue TVs which require a set top box
2. Digital TV Ready (Standard Definition) – for TVs able to receive SD broadcasts
3. Digital TV Ready (High Definition) – for TVs able to receive HD broadcasts
Figure 10: DSTF labelling scheme
Source: Department of Communications
All elements of the DSTF work labelled the switch off of analogue services as the ‘Digital Switchover’.
36
Data extracted from reports available at www.communications.gov.au/television/digital_tv_in_australia/
digital_switchover_reports

43
5.3 Digital switchover timetable
The DSTF issued a consultation paper in May 200837
seeking opinions on which legislative arrangements
should be taken for the switch off of analogue services. A timetable was released in October 2008. Switch
off was planned to occur by licence area as this followed dependant signal paths where often switching off
the main transmitter would mute the following translators and re-transmitters and formed logical areas for
public information campaigns. Actual switch off dates were set by the Minister as target windows of six
months duration, then times were agreed between broadcasters and government to be a mutually
acceptable time when no high rating or especially important programming was scheduled for broadcast
and on a schedule that allowed for timely mobilisation of resources for the public information and
assistance campaigns.
(i) Testing government programmes – Mildura
The campaigns and plans were tested by switching off the Mildura licence area first. This is a smaller
regional licence area. Post switch off surveys were conducted to provide feedback and modify the
campaigns and plans. The remainder of the licence areas were switched off sequentially in a plan as shown
in Table 5.
(ii) Targets achieved
Table 5 shows the timetable regions, the windows originally set and the actual dates the analogue service
was switched off in each region.
For the first two and a half years, switch off was by regional area for each state which formed the major
regional licence areas, with a switch off event in each half of the year. New South Wales has two regional
licence areas. Generally, a date was chosen in the latter part of the six month window.
In 2013 the switch off events were staggered as they covered the metropolitan areas (and Tasmania), so the
affected populations were larger and hence the public information and assistance campaigns were more
intense.
The only licence area to switch outside of its allotted window was Adelaide which actually switched early.
Broadcasters had completed installation of gap filler transmitters in that area early and wanted to push
back the Perth licence area as delays were experienced with approvals for some sites there. However, the
DSTF did not want to push back the Perth switch off outside of its window due to the complicated
requirements of changing legal instruments. As a result, some gap filler sites in the Perth licence area were
not transmitting at the time of analogue switch off, but these commenced service shortly after. Most other
gap fillers were ready in time, some commencing service on the switchover day.
37
DSTF, “Legislative framework for implementing a digital television switchover timetable”, May 2008

44
Table 5: Digital TV timetable by region
Type Switchover Area Window Switchover Date
VIC Mildura / Sunraysia 1 January – 30 June 2010 30 June 2010
SA Broken Hill 1 July – 31 December 2010 15 December 2010
SA Riverland 1 July – 31 December 2010 15 December 2010
SA Mt Gambier / South East South Australia 1 July – 31 December 2010 15 December 2010
SA Spencer Gulf 1 July – 31 December 2010 15 December 2010
VIC Gippsland 1 January – 30 June 2011 5 May 2011
VIC North Central Victoria 1 January – 30 June 2011 5 May 2011
VIC South West Victoria 1 January – 30 June 2011 5 May 2011
VIC Goulburn Valley / Upper Murray 1 January – 30 June 2011 5 May 2011
QLD Wide Bay 1 July – 31 December 2011 6 December 2011
QLD Capricornia 1 July – 31 December 2011 6 December 2011
QLD
Queensland Central Coast &
Whitsundays
1 July – 31 December 2011
6 December 2011
QLD Darling Downs 1 July – 31 December 2011 6 December 2011
QLD North Queensland 1 July – 31 December 2011 6 December 2011
QLD Far North Queensland 1 July – 31 December 2011 6 December 2011
NSW Griffith / Murrumbidgee Irrigation Area 1 January – 30 June 2012 5 June 2012
NSW South West Slopes & Eastern Riverina 1 January – 30 June 2012 5 June 2012
NSW Illawarra and the South Coast 1 January – 30 June 2012 5 June 2012
NSW
Central Tablelands & Central Western
Slopes
1 January – 30 June 2012
5 June 2012
NSW ACT & Southern Tablelands 1 January – 30 June 2012 5 June 2012
NSW North West Slopes & Plains 1 July – 31 December 2012 27 November 2012
NSW Richmond / Tweed 1 July – 31 December 2012 27 November 2012
NSW Northern Rivers 1 July – 31 December 2012 27 November 2012
NSW Hunter 1 July – 31 December 2012 27 November 2012
Metro Tasmania 1 January – 30 June 2013 9 April 2013
Metro Perth 1 January – 30 June 2013 16 April 2013
Metro Brisbane 1 January – 30 June 2013 28 May 2013
Metro Melbourne 1 July – 31 December 2013 10 December 2013
Metro Adelaide 1 July – 31 December 2013 2 April 2013
Metro Sydney 1 July – 31 December 2013 3 December 2013
Metro Darwin 1 July – 31 December 2013 30 July 2013
Remote Remote Central & Eastern Australia 1 July – 31 December 2013 10 December 2013
Remote Regional & Remote Western Australia 1 July – 31 December 2013 25 June 2013

45
5.4 Digital broadcasting network
At the conclusion of analogue switch off, the broadcast network was fully digital. Additional sites had been
integrated into the network as SFNs and the previously community operated facilities had been transferred
to become under the control of the broadcasters.
The network structure is shown in Figure 11, incorporating an SFN for translators and showing the impact
of subsequent policy decisions regarding enhancement of digital coverage and conversion of gap filler
self help transmission sites. It should be compared to the previous analogue (Figure 2) and simulcast
(Figure 7) structures to examine the scale of the changes.
Figure 11: Australian terrestrial TV broadcast overview (Digital)
Source: ITU
Australia digital TV analogue switch off lessons
 Government should conduct regular surveys of households to check that the public have converted to
digital.
 Close consultation is necessary between all stakeholders for a successful switch off of analogue services
and planning is paramount.
 Well designed public information campaigns are needed to ensure the public convert in a timely manner.
 Assistance schemes are needed for lower socio-economic groups in the community to help them convert
to digital.
 Setting target dates provides a firm goal to work towards for all stakeholders. However, the switch off
dates should be set in a manner that it can reasonably be changed if project plans change due to
unforeseen delays.

46
Part 6 – Digital restack
6.1 Introduction
In June 2010, the Australia Government announced that a digital dividend of 126 MHz in the 700 MHz band
spectrum (694-820 MHz), comprised of Australian UHF television channels 52 to 69, would be realised. The
digital dividend is made possible by the move to digital-only television broadcasting under the digital
television switchover program. The final step to realising the digital dividend is for a significant number of
digital television services to be moved to new channels so that channels 52 to 69 can be cleared and made
available for new services such as wireless broadband.
Moving to the new channels has two major phases of work. The first was the development of revised
channel plans and sequencing plans that identify the final channels that digital television services will move
to and the order in which the moves will need to occur. The second was the implementation of those
channel changes by broadcasters.
6.2 Restack and reallocation processes
The announcement of a digital dividend required two streams of work from government. Firstly, the
spectrum needed to be cleared of existing services – the restack of digital television. Secondly, government
wanted to convert the dividend into an asset that could be realised into consolidated revenue at auction.
6.2.1 Clearing the digital dividend
The processes for the ACMA to clear the digital dividend were given by way of Ministerial Direction –
Australian Communications and Media Authority (Realising the Digital Dividend) Direction 2010 – directing
that the ACMA:
 clear part of the Broadcasting Services Band comprising 694-820 MHz as soon as possible after
the analogue switch off;
 consider whether to vary a frequency allotment plan (FAP) under subsection 25 (2) of the BSA
and that in the metropolitan areas there are no more than six channels available;
 consider whether to vary a licence area plan (LAP) so that the main digital services for both
television and radio are broadcast in the same frequency band, e.g. VHF Band III, and for regional
areas that the restack has the objective of minimal disruption and minimal financial impact on
commercial and national broadcasters;
 to vary conversion schemes so that channel allotments are varied not using the digital dividend;
 set aside 14 MHz in VHF Band III for digital radio;
 they provide regular updates to the Minister; and
 they consider if Channel 27 should be expanded to a 7 MHz channel by adding 1 MHz at the lower
end to become 519-526 MHz.
The resulting processes on the ACMA include the work already described above and are shown in the top
half of Figure 12. These were to complete the restack and make spectrum available by 31 December 2014.
Note should be made that although the government had set the timetable to auction the spectrum,
the processes shown in Figure 12 to deliver the spectrum were a task for broadcasters.

47
Figure 12: Government processes and timeline for delivering a digital dividend38
Source: ACMA
6.2.2 Auctioning digital dividend spectrum
The processes for the ACMA to prepare the auction for spectrum could be considered as a separate case
study. In summary, this spectrum was bundled with spectrum in the 2.6 GHz band, also to be cleared by
broadcasters who use it for electronic news gathering links.
38
14-15 March 2012 – Digital Broadcasting – a 2012 roadmap – speech by Giles Tanner, General Manager, Digital Transition
Division, ACMA, to the Broadcasting Australia Conference and Expo 2012, Sydney Slide 7
www.acma.gov.au/~/media/mediacomms/Presentation/Powerpoint/Broadcast%20Sydney%20Expo.PPT

48
Figure 13: Successful bidders for digital dividend spectrum auction
Source: ACMA
(i) Preparing for the auction
In the lower half of Figure 12 are shown the regulatory processes for auctioning the digital dividend
spectrum. To prepare a spectrum licence, the ACMA must first create a technical framework.
As broadcasters were likely to be impacted by the new transmissions in the digital dividend spectrum, they
were involved in the consultations undertaken to develop the technical framework. At the same time,
Australian delegations to the regional spectrum group, the Asia-Pacific Telecommunity (APT) Conference
Preparatory Group (APG) were involved in the development of what ultimately became known as the APT
700MHz band plan (see next Section) and this was adopted as the band plan for the spectrum auction.
The technical framework became part of the marketing plan defining such items as unacceptable
interference and advisory guidelines for managing interference from transmitters and into receivers and
these form part of the licence conditions. All of these processes were performed under the
Radiocommunications Act 1992.
A separate consultation was undertaken by the ACMA to determine the auction lot size, determining the
geographic boundaries and range of frequencies for each lot to be auctioned. The ACMA determined that
they would auction nine 2 x 5 MHz Australia–wide lots consistent with the APT band plan.
(ii) Auction result
After undertaking a combinatorial clock auction, Australia’s two largest mobile telecommunication carriers
were successful in securing 2 x 10 MHz (Optus) and 2 x 20 MHz (Telstra) and 2 x 15MHz remains unsold. The
important technical consideration for broadcasters was the adjacent licence to Channel 51 would be Optus
with a 10 MHz allocation, which sets the characteristic of out-of-band noise for the user equipment (UE)
which may be mobile handsets or USB devices for laptop computers etc. While these devices may be
manufactured to meet the 3GPP specification ETSI TS 36.101, slightly different limits apply in Australia.
(iii) Adjacency issues of the 700 MHz Plan
The Spectrum Marketing Plan for the Digital Dividend Auction39
has defined the limits on spurious and non-
spurious emissions from transmitters operating in the band 703-748 MHz. The non-spurious levels are
shown in Figure 14 along with the differences from the 3GPP specification.
39
Radiocommunications Spectrum Marketing Plan (700 MHz Band) 2012 www.comlaw.gov.au/Details/F2012L02547

49
The out-of-band emission levels were developed by the APT over the course of a number of meetings where
a level of –34 dBm/MHz was set for protection to broadcast services. The 3GPP specifications have been
updated to include a spurious emission limit of –26.2 dBm/6MHz40
equivalent to –34 dBm/MHz. The
standard emission mask has different break points and levels than the Australian mask (refer Figure 14)41
.
The ACMA has applied tighter limits across the broadcast channels, lowering the limit to –40 dBm/MHz
below 694 MHz but allowing this level to be relaxed to –34 dBm/MHz across channels 49, 50 and 51 in areas
where there are no television services operating in those channels.
Figure 14: Out of band emission limits for IMT UE in the lower band (703-748 MHz) in Australia
Source: ACMA and 3GPP
To know whether this level adequately manages the interaction between the adjacent services will only be
known after the IMT services have been in operation for some time and the population of mobile terminals
becomes representative across the community. Leading up to the APT meetings, broadcasters had put the
case for much lower limits on out-of-band emissions, arguing that the levels should be set 10 dB lower
(–50 dBm/MHz) to protect a viewer with suburban grade coverage interfered by a mobile device just over
10 metres from their antenna or a rural grade viewer 50 metres from their antenna.
The ACMA view was that probabilistic factors should also be considered which would lower the chance of
interference occurring to what they considered an acceptable level, rather than just the deterministic
factors presented by broadcasters.
6.3 Planning the restack
During the simulcast period, the broadcasting services bands had fifty seven 7 MHz channels to support
5 analogue television networks, 5 digital television networks, 2 future digital networks and 1 digital radio
allocation. After switching off analogue, the replanning task for restack was to support 6 digital television
networks and have 2 channels for digital radio in thirty two 7 MHz channels.
40
Band 28 in Table 6.6.3.2-1 of ETSI TS 136 101 V11.9.0 (2014-08)
41
10 MHz case Table 6.6.2.1.1-1 of ETSI TS 136 101 V11.9.0 (2014-08)
3GPP OoB Mask
-25dBm/MHz
3GPP Spurious Mask
-34dBm/MHz

50
A Restack Planning Advisory Group (RPAG) was established by the ACMA to consult industry on the
restacking of digital television services. The RPAG was an informal consultative group for the regulator to
seek industry views and consisted of representatives of all broadcasters and transmitter facility providers,
some industry consultants and radio interests. The RPAG provided a forum for the ACMA and industry to
discuss proposals relating to replanning of digital television channels to facilitate the restack as well as
restack implementation and timing issues.
Restack provided an opportunity for the industry to review and clear the legacy of many planning decisions
that had been taken over the years for very good reason at the time, but now, after analogue switch off,
left anomalies in the broadcast system.
6.3.1 Core issues
(i) Planning methodology
Over 930 services were identified as operating in Channels 52-69 that needed to be moved to a channel
below 52. The eventual planning resulted in 1 299 services being restacked (including consequential moves,
see below) in 367 transmission areas (there are over 580 terrestrial transmission areas in Australia). Faced
with the massive planning task in a short timeframe, while resources were still being deployed on installing
gap filler translators, the broadcasters developed a ‘block’ model plan which would offer coverage benefits
and greatly simplify the planning of adjacent market services. The block planning approach takes a "green
field" approach to channel allotments for each transmission site, placing all services at a site in one of five
blocks of six contiguous channels. In the metropolitan markets during simulcast, digital services were
broadcast on channels 11 and 12, so the viability of adjacent services was proven.
Figure 15: Block model channel planning
174 DAB+ 230 526 568 610 652 694 MHz
Source: ACMA
The ACMA had commenced their plans based on a "minimal moves" approach, in the belief that this would
lead to the minimal cost for restack. This approach aims to minimise the number of channel moves by only
changing the channel allotments where absolutely necessary. A necessary move is either: one where the
current channel is in the digital dividend band, or a consequential move to make way for another service to
move, with consequential planning work required as well. Previously, under "interleaved" planning services
were widely spread across a band or across VHF and UHF Bands, this was sometimes not the case, but the
remaining channel spreads were very wide.
In detailed studies modelling the channel changes required in Queensland, the ACMA found that 53 of
75 transmission sites had channels above channel 51 and at these sites there were a total of 198 channels
in use that were above channel 51. Under the minimum moves approach, 46 services operating on a
channel below 52 needed to also change channels (a ‘consequential move’). Changing to the block plan
required 83 consequential moves. Further modelling was undertaken based on the Queensland studies to
estimate the differences in cost and time and any other benefits. As a result of these studies, the ACMA
agreed to the block plan, finding the block plan would take slightly longer (15 per cent) to implement and
may cost slightly more (9 per cent) to implement than the minimum moves, will result in similar levels of
viewer cost and disruption, but the block model offers long term benefits including better and more
equitable coverage, simpler and smaller receive antennas for viewers and master antenna television
systems would be simpler and cheaper.
6 3934332812 40 45 46 51
Block A Block B Block C Block D Block E

51
(ii) Review of planning field strengths
All the original planning was on the basis of broadcasters using the DVB-T standard with transmission
parameters of 8k, 64QAM, 2/3 forward error correction (FEC) and 1/8 guard interval (GI) to provide
a 19.3 Mbit/s payload in a 7 MHz channel, but in order to accommodate the SD / HD simulcast, most
broadcasters were transmitting 8k, 64QAM, 3/4 forward error correction (FEC) and 1/16 GI to achieve
a 23 Mbit/s payload. Changing the FEC requires an increase in the minimum C/N (or co-channel protection
ratio) by 1.6 dB.
Also, as the top frequency in the broadcast band was to be reduced from 820 MHz to 694 MHz, this will
reduce the 20*log(f) losses by 1.5 dB. Now that the frequency spread of the UHF broadcast services band
had been reduced from 300 MHz to 174 MHz, consideration was given to having one planning value for the
whole band rather than two previously (for Band IV and Band V).
Due to industry concerns, the ACMA decided to continue with the planning parameters that have been used
to plan the introduction of digital television as set out in the ACMA DTTB Planning Handbook. However, due
to the adoption of block planning some adjustment is unavoidable to the boundary of where the different
UHF minimum median field strengths apply, so the break point was changed from between channels 35 and
36 to fall between channels 39 and 40, so each block of channels had a consistent planning value. Consistent
with the reconfirmation of the existing technical planning parameters, the ACMA retained the assumed
forward error correction (FEC) parameter for planning purposes at 2/3 FEC, instead of the proposal to adopt
the 3/4 FEC value. However, recognising the proposal to break up wide area SFNs it adopted a 1/16 guard
interval.
(iii) Planning for DAB+
The Ministerial Direction (see Section 6.2.1) required 14 MHz to be set aside for DAB+. Several methods of
sharing the VHF band with digital television services, but due to the different protection ratios involved
between DAB and DAB, and between DAB and DTV, it was found that spectrum was better utilised if a
sub-band could be developed so that DAB / adjacent area DTV co-channel arrangements were avoided.
Given that DAB+ digital radio services commenced in the five major capital cities in July 2009, and channel
9 analogue was to be switched off, a sub-band of VHF channels 9 and 9A are able to be left clear for digital
radio use in metropolitan and regional areas.
(iv) Other issues
Other key issues discussed were:
 channel assignment rules, important to broadcasters from the aspect of inputs to translators in
one channel block, needing to avoid the adjacent channel to transmit in the next channel block;
 as mentioned in Section 3.5 (ii) different SFN configurations serving the same area had created
problems for reception, so all SFNs between broadcasters were to be of the same structure; and
 channel planning in specific areas where spectrum is used more densely to agree on suitable
channel arrangements.
6.3.2 Restack objectives
The RPAG was an important part of the process for the development of formal instruments but it did not
replace public consultation on formal instruments. After discussion within the RPAG forum, particularly
around the core issues, and a formal public consultation, in May 2011 the ACMA adopted a series of restack
objectives and principles. The objectives were:

52
1 Clear the digital dividend band of broadcasting services as soon as practicable.
2 Plan for six digital channels at each transmission site42
.
3 Plan for six VHF channels at all metropolitan main station sites.
4 Plan such that coverage of all six channels is similar.
5 Maintain or improve digital television coverage.
6 Simplify viewer reception of terrestrial digital television.
7 Establish spectrum planning arrangements that support future needs.
8 Retain 14 MHz of spectrum in VHF Band III for possible expansion of digital radio.
9 Comply with the legislated framework.
10 Consistent with the minister’s direction, the ACMA should wherever possible:
a) minimize viewer costs and disruption;
b) minimize commercial and national broadcaster costs.
6.3.3 Restack planning principles
The restack planning principles were as follows:
Principle 1: Replan digital television services to use VHF channels 6-12 and UHF channels 28-51.
Principle 2: Create a digital radio sub-band, comprising VHF television channels 9 and 9A that is clear of
digital television in metropolitan and regional licence areas. Where practicable, also avoid planning new
services on these channels in remote licence areas.
Principle 3: Plan for six digital channels at each transmission site, except for
i) licence area overlaps where two sets of three commercial services will require channels (a total of
nine channels); and
ii) where broadcasters operate from different sites but cover the same area.
Principle 4: Plan channels so that viewers in metropolitan and regional licence areas can receive all services
using a single band antenna (i.e. plan all channels in either the VHF or UHF band). Consider the benefit of
single band operation in other areas on a case-by-case basis. The current polarization of the existing
transmissions in a particular band at each transmission site is to be maintained.
Principle 5: Plan all six services on channels within defined blocks of channels as follows43
:
Block A: 6, 7, 8, 10, 11 and 12*
Block B: 28, 29, 30, 31, 32 and 33
Block C: 34, 35, 36, 37, 38 and 39
Block D: 40, 41, 42, 43, 44 and 45
Block E: 46, 47, 48, 49, 50, and 51.
* Channels 9 and 9A may be used for digital TV in some remote areas.
42 In licence area overlap regions, nine services per site would be planned at existing transmission sites.
43
In remote areas where there was no spectrum scarcity, a Block BC, Block DE plan was used to leave channels clear
between digital channels and hence relax antenna combiner specifications.

53
Principle 6: Assign channels within a block as follows.
VHF: Existing VHF services to retain current channels unless they have to move to clear channels 9 and 9A
under Principle 2. New or changed channel assignments do not need to follow any particular order, except
in all Metropolitan areas where SBS should move to channel 7. Where it is possible without moving existing
services, channel 10 should be the unassigned channel to align with the metropolitan area unassigned
channel.
UHF: Channel assignments should be made after considering and balancing a number of objectives
including:
– avoiding off-air input issues (adjacent channel and N+5);
– avoiding changes to existing services within the block;
– using the unassigned channel to remove restack timing constraints and manage band edge
interference potential.
If none of the above issues apply, UHF channels should be assigned in the following order: SBS, ABC, Seven
(or affiliate), Nine (or affiliate), Ten (or affiliate), Unassigned.
Principle 7: In selecting the channel block for a transmission site:
– Consider the channels used by existing digital services and any information available on the
operating frequency range of broadcaster transmission equipment.
– Avoid use of a block outside the likely bandwidth of viewer antennas. In particular, avoid Block B
where there is no current or past use of UHF Band IV channels. Where this cannot be avoided,
minimize the total population affected.
– Wherever sites utilize UHF channel blocks, attempt to place high power services on lower UHF
channel blocks.
Principle 8: Break up wide area single frequency networks (SFNs) known to have associated reception
problems and minimize use of new SFNs where possible.
Principle 9: Plan on the basis of broadcasters using the DVB-T standard with transmission parameters of 8k,
64QAM, 2/3 forward error correction (FEC) and 1/16 guard interval.
The co-channel protection ratio used for planning is: 20 dB.
The minimum median field strengths used for planning is shown in Table 6:
Table 6: Minimum median field strengths for restacked digital television planning (dBµV/m)
VHF (Block A)
(174-230 MHz)
UHF (Blocks B and C)
(526-610 MHz)
UHF (Blocks D and E)
(610-694 MHz)
Rural Sub-
urban
Urban Rural Sub-
urban
Urban Rural Sub-
urban
Urban
Minimum median field
strength (dBuV/m)
44 57 66 50 63 71 54 67 74
Principle 10: Equalize transmissions across all broadcasters as far as practicable through planning on the
basis of equal ERP levels, identical antenna patterns, closely sited transmitters and all broadcasters having
the same SFN arrangement.
Principle 11: Determine the timing constraints on channel availability and specify a minimum window of
six months, where practicable, when both the current digital and the final digital channels are available.
When all sites and timing windows are considered together, they should result in the digital dividend
channels (52-69) being cleared as soon as practicable, and by the end of 2014 at the latest.

54
6.3.4 Television licence area plans
Following discussions with the industry through the RPAG, the restack channel planning proposals were
codified in legislative instruments known as Television Licence Area Plans (TLAPs). These instruments
identified the channel allotments each digital television service would need to move to, if it needs to
change, and by when the changes need to be made. The draft instruments were made available for a period
of formal public comment before being considered for approval by the ACMA. Refer to Section 1.6.2 (iii) for
a discussion on TLAPs and the Australian planning regime.
6.3.5 Indicative restack channel chart
Detailed restack channel planning work commenced in 2011 and continued until late 2012. In the early
stages of channel planning, to provide a framework that allowed the detailed channel planning for each
licence area to proceed relatively independently, a ‘key sites indicative channel plan’ was developed. It has
now been superseded by a more comprehensive Digital Television Channel Chart that consolidates in a
single spreadsheet the detailed channel planning work that the ACMA has performed for each of the
television licence areas.
6.4 Implementing the restack
In order to minimise viewer disruption, all changes to affected services at a transmission site would need
to occur simultaneously. This required a high level of industry cooperation and coordination. The ownership
structure of equipment and transmitter sites in Australia is quite complex. The site owner may be a
broadcaster or a transmission facility provider who leases equipment room space and tower space to each
broadcaster (or if they have arrangements with another facility provider, with the provider). The common
transmission equipment, the combiner, feeders and transmitting antenna array may be owned by one party
and an access fee charged to the other broadcasters. The common interface point between broadcaster’s
systems is into the combiner. Hence regardless of the implementation method used, that a paradigm shift
from the legacy, largely individual broadcaster, method of implementing changes to infrastructure, to a
more holistic industry level approach will be necessary to achieve restack in the desired timeframe.
After negotiations with the industry, the Australia Government committed to:
– relocate commercial and national broadcaster digital television services to their new channels by
retuning, replacing or otherwise modifying transmission equipment to operate below UHF
channel 52 (694 MHz);
– provide a project and implementation manager to manage channel changes nationally; and
– conduct a public education/information campaign about the need to retune receivers.
Program implementation manager
The government appointed a Program Implementation Manager (PIM) in mid 2012 to act on behalf of the
government and liaise with all broadcasters and infrastructure owners to put in place all necessary actions
to restack digital services.
The programme was in two phases:
 Phase 1 – Develop a Timeline: liaising with all affected parties, identifying top level scope of works
for sites which involve a technical evaluation, develop an installation approach, gauge industry
capacity to make the changes, report TLAP windows to the ACMA by July 2012 and deliver a final
plan by November 2012.
 Phase 2 – Implement the plan: including developing technical specifications, purchasing all
equipment, detailing scope of works and bills of material for each site, engaging contractors to
undertake the work, making payments and reporting to the government.
As this programme was to modify the assets (transmitters etc.) of each broadcasting company or facility
provider, detailed legal contracts were required.

55
Broadcasters required service outages to be of a minimum duration for implementing the changes. Outage
‘windows’ were agreed between midnight and dawn with a backup time during the middle of the day.
Periods where significant programming was scheduled were excluded from the outage times.
Some of the transmitters to be retuned were over 10 years old. Investigations showed these could not be
retuned within a short timeframe to meet the minimal outage requirements and required specialist original
manufacturer skills. Product development in the intervening time made it easier and without a cost penalty
to replace rather than retune many transmitters.
Digital / digital simulcasts were agreed at a number of sites servicing areas of high populations of multi
dwelling units (MDUs) where it was considered likely there were channelised headends which needed
modification by antenna installers, hence and viewers were not able to retune their receivers at
a nominated time.
The project required the commissioning of installation teams contracted from industry, manufacturers and
overseas resources to undertake the work in a two year period. Approximately 400 transmitter sites were
involved in the project affecting over 1 200 transmitters, plus input signal receiving equipment.
The interdependencies of channel allotments between transmitter sites was immense. Channels at some
sites need to be cleared before an adjacent site is able to be restacked onto its final block of channels,
a ‘domino effect’ of interactions impacted on the project plan. Generally sites were visited twice; all
installation work undertaken which did not result in a channel change was undertaken at least 6 weeks
prior to the scheduled retune date. A firm retune date was then set and the viewer communications
campaign commenced to inform the public of the retune date. The site was then re-visited and equipment
connections swapped and transmitters retuned where practicable during an outage to effect the restack.
Retuning of combiners on site was not considered feasible, so replacements were purchased and swapped
out.
Some sites required a band change from VHF to UHF or vice versa. These sites involved extensive work and
extended outages. Some sites also required transmit antenna replacements as the restacked channels were
outside of the operating range of the original antenna. Extended outages were required at these sites as
well.
Although the PIM was funded by government, documentation such as scopes of work and bills of materials
were approved by the broadcast engineering staff. This workload of documentation and the need to visit
sites for acceptance testing has placed a large burden and been costly to broadcasters and facility providers.
The Australia Government expects that the channel changes will be completed by 31 December 2014.
A channel change timetable schedule that advises of nationwide activities and particularly public retune
dates is published on the website of the Department of Communications44
and is fed into the public
information campaign.
6.5 Public information campaign
The restack programme affected the very large majority of Australian television viewers. Viewers did not
need to purchase new television reception equipment, but have generally needed to retune their existing
television, set top box or digital recorder to be able to continue viewing free-to-air services that have
undergone a channel change. Therefore a very widespread public information campaign was required to
deliver the message to viewers that at a nominated time, they needed to have their receiver rescan for
digital television services.
The message needed to be delivered in a simple, clear and concise manner. The industry jargon of
rescanning a television was seen as confusing, but ‘retuning’ was a well understood term with connotations
of the analogue days of ‘tuning’ a set.
44
www.communications.gov.au/television/achieving_the_digital_dividend_-_restack

56
An animated stylised figure of a talking remote control was used as the centrepiece of the campaign. "Roy
the Remote" focussed the public’s attention that the retune action would be undertaken using their remote
control. "Roy" was used in press advertisements, television commercials and video promotions to convey
the messages about what to do and when to retune.
Figure 16: "Roy the Remote"
Source: Department of Communications
Extensive website resources were developed to provide additional information for the campaign including
a geographic information system whereby householders could enter their address and specific timing and
tuning information for their location was displayed. Visit http://retune.digitalready.gov.au/ for more
information.
6.6 Planning and implementation example
An example of the changes to transmitter configurations, and special cases considered, is provided in the
Plots in Figure 17 in this Section.
The Sydney licence area has translators at Manly and Kings Cross and Bouddi, Gosford and Wyong which
are in an area known as the Central Coast of the state of New South Wales and a licence area overlap with
Newcastle (located to the north of Sydney), so these sites transmit 8 services today (future planning is for
9 services). In each figure, the translators at Manly, Bouddi and Gosford are shown as "Sydney translators"
while the most distant site at Wyong is shown in the line above as an "Adjacent Licence Area Transmitter"
as in analogue mode it shared channels with Manly. Additionally, a community television channel is
broadcast in digital on a temporary channel allotment (channel 29) from one of the main Sydney transmitter
sites. For simplicity, the nearby Kings Cross site is not shown. The other "Adjacent Licence Area Transmitter"
site in this example is the main Newcastle site.
Again, not shown for simplicity is another adjacent licence area transmitter site, Wollongong, located to the
south of Sydney and has many co-channel assignments with Newcastle, but the Wollongong transmissions
need to be considered in planning for this area as its transmitter does reach across Sydney and is able to be
received in digital across many localities served by the Manly transmitter.

57
The nomenclature used for each transmitter is its three letter station call sign, followed by the channel
number, then the transmission site name. Where assignments are in an SFN, only the first letter of the site
is shown. E.g. Bouddi, Gosford and Wyong are operated as an SFN in digital mode, so the site names are
shortened to B G W.
Note that the Sydney main transmitters operate on VHF channels and are not shown in this example which
only illustrates services operating on UHF channels.
Figure 17: Channel changes for Sydney coastal translators
The distance between the Manly and Newcastle transmitter sites is 103 km.
Colour coding has been included to identify the type or action taken on
a transmitter. The community television transmitter is shown in a slightly
different colour as it is the only community transmitter.
Source: ITU
Plot 1 shows the channel assignments during the simulcast period. Note the spectrum congestion.
Plot 1: Simulcast
Source: ACMA
Plot 2 shows the digital channels that remain after analogue switch off was completed.

58
Plot 2: After analogue switch off
Source: ACMA
Plot 3. Manly serves an area that has a high concentration of MDUs, so a digital simulcast was undertaken
as part of the restack project to allow time for MDU master antenna television systems, which may have
channelised headends, to be modified by installation staff. Block B is fully occupied at this stage.
Plot 3: Manly digital simulcast
Source: ACMA
Plot 4, TEN45 and ATN48 switched off and Newcastle restacks to Block C and clears Blocks D and E ready
for the Central Coast Restack.

59
Plot 4: Manly digital simulcast ends, Newcastle restacks
Source: ACMA
Plot 5, Central Coast digital services restack into Blocks D and E, splitting the troublesome SFN that was on
ABC37. Digital dividend spectrum is available for new services.
Plot 4: Restack complete, digital dividend spectrum re-allocated
Source: ACMA

60
Australian digital TV restack lessons
 The appropriate size of "digital dividend" that can be released should be studied to ensure that adequate
spectrum remains available to maintain a high quality television broadcasting service.
 "Block model" planning has been successful, reducing planning time and resources and providing better
more consistent reception by households.
 The complexity of a restack of television channels should not be underestimated.
 Restack is technically very complex, but needs to be communicated to the public as a simple process.
 The key message for the public to retune on a single switchover day can be successful.
 The need for digital / digitals simulcasts should be considered for sites that serve high populations of
MDUs.
 A high level of industry cooperation and coordination is required for a successful restack.
 It should not be assumed that transmitters may be simply changed to another channel.
 Appropriate conditions should be set for the new services that are to occupy the digital dividend
spectrum so that there is preferably no or minimal impact on broadcasting services.

61
Part 7 – Summary and conclusions
7.1 Summary
The Implementation of Digital Terrestrial Television Broadcasting in Australia has been undertaken in five
stages over a period of 21 years, with many stages overlapping.
Initial investigations were conducted jointly by representatives of government and broadcasters, but once
the decision had been made, it was the broadcasting community who financed and provided resources for
implementation of digital services. This pattern continued during the digital enhancement stage.
Broadcasters have been the beneficiaries of these stages, providing a more flexible broadcast system
offering more programmes the viewing public at a higher broadcast quality, so, in addition, the public have
been beneficiaries of these Stages for the cost of a new television receiver.
After the digital broadcasting system was established, the following two stages of analogue switch off and
digital restack were led and funded by the government as they were the beneficiary of these actions, the
auctioning of cleared spectrum converting a spectrum asset into government consolidated revenue.
This shift in leadership, funding and resources for the conversion project are demonstrated in Table 7. Note
that many of the stages will overlap each other.
Table 7: Leadership, Funding and Resources for Implementing DTTB in Australia
Stage / Duration Stage Leader Activity Funding Resources
Preparation &
Planning
(8 years)
Government &
Broadcasters
Initial Work
Government &
Broadcasters
Domestic Planning Government / ACMA
Standards
Development
Government, Broadcasters
& Industry
Implementation
(7 years)
Broadcasters
Installation &
Operation Broadcasters Broadcasters
Market Survey Industry
Public Information
Campaign Broadcasters Broadcasters
Digital
Enhancement
(8 years)
Broadcasters
Planning
Broadcasters &
Government
Broadcasters &
Government
Implementation Broadcasters Broadcasters
Public Information
Campaign
Integrated with ASO
messages
Analogue Switch
Off
(6 years)
Government
Planning Government
Government &
Broadcasters
Implementation Broadcasters
Assistance Schemes Government Contracted by Government
Public Information
Campaign Government Government
Digital Restack
(5½ years)
Government
Planning Government
Government &
Broadcasters
Implementation Government
Contracted by Government
& Broadcasters
Public Information
Campaign Government Government

62
7.2 Key lessons
The key success factors of the conversion of broadcasting to digital in Australia have been:
 the maintenance of a close working relationship between government and broadcasters;
 open communication with the public, to seek feedback on reception conditions and communicate
changes;
 the development of standards to modify a ‘tool kit’ of international standards to incorporate local
requirements;
 planning each stage is key, every detail must be examined.
The key lessons learned:
 set regular reviews to examine if policy and technical goals are being achieved;
 survey households from an earlier stage to judge the success of the conversion;
 setting target dates provides a firm goal for all parties to work towards;
 effort is needed to educate the public from ‘analogue’ to ‘digital’ thinking; influencing perceptions
of degraded reception (‘digital cliff’), channels to services and new features;
 every householder’s reception conditions are different, a variety of causes and solutions to
reception issues need to be developed;
 with respect to analogue switch off and the digital restack:
 review digital coverage before considering the size of a digital dividend;
 use the restack to address legacy broadcast planning issues;
 a common retune day can be successful for a small group of sites only after considerable
planning.
7.3 The future
The broadcasting industry was able to make the transition from analogue to digital only because spectrum
was available (as "taboo" channels were unable to be used by other analogue services) within the bands
compatible with television receivers.
However, the result of this project, digital services have consumed nearly all available remaining spectrum
after releasing the "digital dividend" spectrum, so this option is not available for the next ultimate change
in broadcasting technology.
The first nearly 20 years of Australian television were black and white analogue broadcasts. Colour was
added in 1975 and stereo sound in the mid 1980s, all based on compatible modulation schemes.
The introduction of digital in 2001 was the first time additional spectrum was required for a technology
change and while some encoding changes could be made on the existing platforms e.g. to use advanced
coding such as H.264 AVC, the current broadcast modulation platforms will not support sufficient payloads
for the next quantum leap in technology. Based on history, television has a major technology change on
average every 15 years, so the next change is imminent.
That leap is developing to be 4K video. Already many Australian video production companies are producing
content in 4K. As Australians have shown with many technologies in the past, for example the acceptance
of HDTV, they will want UHDTV in the future.

63
Hence, yet another new modulation platform will be required. DVB-T2 builds on lessons learnt by the
members of the DVB Project and would offer in an Australian environment a capacity increase of
approximately 40 per cent, combined with the better encoding algorithms in H.265 HEVC, could make
terrestrial transmission of 4K feasible. DVB-T2 receivers have been in production for the last few years.
H.265 HEVC decoding is in a prototype phase so it will not be long before the product is available.
Australian broadcasters have already begun a detailed technical examination of H.265 HEVC coding and use
of DVB-T2 modulation, but any formal move to this as a broadcasting standard would first be subject to
government approval. But, as was the case for the transition to DVB-T, there will be many challenges to
overcome, particularly in a constrained spectrum environment that now exists in the broadcasting bands.
7.4 Conclusions
What started out as an engineering-led concept to deliver to the viewing public higher quality broadcast
pictures and sound has opened up challenges and opportunities that are inherent with any disruptive
technological change. The transition to digital television has touched in some way every Australian; whether
it be their need to purchase a new television receiver to continue to watch the shows they like or change
the time they watch those shows as digital recorders have made "time shifting" a reality, businesses that
have been rejuvenated implementing the changes, competitive media outlets who have had to change their
business models or even to minority groups such as the hearing impaired who now enjoy a wider variety of
captioned programmes. The impact has been greatest on two groups; broadcasters and government.
The issues for government have been immense to chart a course through the political, social, economic and
technological issues.
For broadcasters, every part of their business operations have changed. Changes have been required from
camera to transmitter and every piece of equipment along the system chain. Delivering better pictures and
sound to the viewer only highlighted the limitations in equipment used for contributing programmes to the
broadcaster. More services have been added by each broadcaster, the presentation facilities for each
service have changed from a local operation to aggregated national operations. The digitisation of studios
has led to new workflows allowing more rapid response to breaking news stories, shortened production
times and added flexibility as to what to put to air.
Has the transition been a success? Undoubtedly the answer is in the affirmative. Analogue has been
switched off, very few, if any viewers were lost in the conversion to digital television. Whilst the timeframe
might be considered long by some commentators, it must be remembered that Australia was one of the
"early adopters" of digital television and conversion rates only increased when consumer technology
features and price points matched the public’s expectations of the new system. Others have benefitted
from the process as well though the work undertaken jointly by broadcaster’s and the regulator’s
engineering work refining the platform and offering that as contributory work to the ITU-R for other
Administrations to build their systems on the work done in Australia.

64
Glossary of abbreviations
3GPP 3rd Generation Partnership Project (a project of 6 telecommunication standard
development organisations)
64-QAM 64-state Quadrature Amplitude Modulation
ASO Analogue Switch-Off
ATSC Advanced Television Systems Committee
AVC Advanced Video Coding
C/N Carrier to Noise ratio
COFDM Coded Orthogonal Frequency Division Multiplex
CRT Cathode Ray Tube
DAB Digital Audio Broadcasting
DAB+ Digital Audio Broadcasting, improved system
DTTB Digital Terrestrial Broadcasting
DVB Digital Video Broadcasting
DVB-T Digital Video Broadcasting – Terrestrial
DVB-T2 Digital Video Broadcasting – Second Generation Terrestrial
EPG Electronic Program Guide
EIRP Effective Isotropic Radiated Power
ERP Effective Radiated Power
ETSI European Telecommunications Standards Institute
FEC Forward Error Correction
FTA Free To Air
GPS Global Positioning System
HDTV High Definition Television
HEVC High Efficiency Video Coding
IBA Independent Broadcasting Authority
IDTV Integrated Digital Television set
IEC International Electrotechnical Commission
ISDB-T Integrated Services Digital Broadcasting-Terrestrial
ISO International Organization for Standardization
ITU International Telecommunication Union
ITU/BDT International Telecommunication Union/Telecommunication Development Bureau
ITU-D International Telecommunication Union – Development sector
ITU-R International Telecommunication Union – Radiocommunications sector
JTC Joint Technical Committee
MHz Mega Hertz
LCD Liquid Crystal Display

65
LTE Long Term Evolution
MAC Multiplexed Analogue Component
MATV Master Antenna Television System
MPEG Moving Picture Experts Group
MPEG-4-AVC Moving Picture Expert Group – Advanced Video Coding
OFDM Orthogonal Frequency Division Multiplex
OoB Out of band
PAL Phase Alternating Line; analogue colour TV system
PSI Program Specific Information
QEF Quasi Error Free
QPSK Quadrature Phase Shift Keying
RF Radio frequency
SDTV Standard Definition Television
SFN Single Frequency Network
SFN Single Frequency Network
SI Service Information
TS Transport Stream
Tx Transmitter
UHF Ultra High Frequencies
VHF Very High Frequencies
VSB Vestigial Side Band
USB Universal Serial Bus
Specific Australian abbreviations
ABA Australian Broadcasting Authority (now part of ACMA)
ABC Australian Broadcasting Corporation
ACA Australian Communications Authority (now part of ACMA)
ACMA Australian Communications and Media Authority
DBCDE Department of Broadband, Communications and the Digital Economy
(became Dept. of Communications)
DCITA Department of Communications, Information Technology and the Arts
(became DBCDE)
DSTF Digital Switchover Task Force
DTCPCG Digital Television Channel Planning Consultative Group
FACTS Federation of Australian Commercial Television Stations
SBS Special Broadcasting Service
SMA Spectrum Management Authority (merged into the ACA)

66
Acts
BSA Broadcasting Services Act 1992
RCA Radiocommunications Act 1992
Instruments
CTC Commercial Television Conversion Scheme
DCP Digital Conversion Plan
LAP Licence Area Plan
NTC National Television Conversion Scheme
TLAP Television Licence Area Plan

67
References
Australia Government
Legislation and legislative instruments
Radiocommunications Act 1992 www.comlaw.gov.au/Details/C2013C00586
Broadcasting Services Act 1992 as amended www.comlaw.gov.au/Details/C2014C00649
Broadcasting Legislation Amendment (Digital Television) Act 2006
www.comlaw.gov.au/Details/C2008C00351
Bills Digest No. 178 1997-98 Television Broadcasting Services (Digital Conversion) Bill 1998
www.aph.gov.au/Parliamentary_Business/Bills_Legislation/bd/BD9798/98BD178
Broadcasting Services (Technical Planning) Guidelines 2007 as amended
www.comlaw.gov.au/Details/F2009C01061
Radiocommunications Spectrum Marketing Plan (700 MHz Band) 2012
www.comlaw.gov.au/Details/F2012L02547
Government departments
Australian Bureau of Statistics, Population Clock www.abs.gov.au/
Australian Government, "DCITA, READY, SET, GO DIGITAL A Digital Action Plan for Australia", November
2006
S Conroy (Minister for Broadband, Communications and the Digital Economy), "Digital television
Australia-wide", media release, 11 January 2010
Department of Communications, Corporate Plan 2014-17, www.communications.gov.au/__data/assets/
pdf_file/0017/214064/Corporate_Plan_PDF_WEB.PDF
P. Spence, "The Australian Regulatory Environment, The Digital Role of the Department of Broadband,
Communications & the Digital Economy", www.acma.gov.au/webwr/_assets/main/lib311250/
the_aust_regulatory_environment-dbcde.pdf
Switchover Taskforce, HAS Brochure, November 2011 retrieved via
www.headwaytas.net.au/attachments/article/145/HAS%20brochure.pdf
Digital Switchover Taskforce, Satellite Subsidy Scheme Brochure, December, 2011 retrieved from the
Byron Shire Council website www.byron.nsw.gov.au/
Digital Switchover Taskforce, "Legislative framework for implementing a digital television switchover
timetable", May 2008
Digital Switchover Taskforce, "Digital Tracker Surveys", www.communications.gov.au/television/
digital_tv_in_australia/digital_switchover_reports
Australian Communications and Media Authority (and its predecessor organisations)
Australian Broadcasting Authority, Specialist Group on Digital Terrestrial Broadcasting, Digital terrestrial
television broadcasting in Australia, First report, ABA, 1995
Australian Broadcasting Authority, Specialist Group on Digital Terrestrial Broadcasting, "Digital terrestrial
television broadcasting in Australia : final report of the Australian Broadcasting Authority Digital Terrestrial
Television Specialist Group."
G. Tanner, Digital Broadcasting – a 2012 roadmap, speech presented at the Broadcasting Australia
Conference and Expo 2012, www.acma.gov.au/~/media/mediacomms/Presentation/
Powerpoint/Broadcast%20Sydney%20Expo.PPT

68
ABA (now ACMA), DTTB Planning Handbook – March 2005.
www.acma.gov.au/~/media/Licence%20Issue%20and%20Allocation/Publication/pdf/Digital%20Terrestrial
%20Television%20Broadcasting%20Planning%20Handbook%20including%20technical%20and%20general
%20assumptions.pdf
ACMA, Final Licence Area Plans, available from www.acma.gov.au/Industry/Broadcast/Spectrum-for-
broadcasting/Spectrum-radio-broadcasting/final-licence-area-plans-broadcast-planning-acma
ACMA, Licence area populations in the ACMA BSA Section 30 Schedule
www.acma.gov.au/webwr/aba/licplan/planning/licareas/documents/bsa_92_s30_schedule.pdf
ACMA Licence Area Definitions www.acma.gov.au/Industry/Broadcast/Spectrum-for-
broadcasting/Spectrum-digital-television/broadcasting-licence-areas-television-acma
Australia Industry
Australian Broadcasting Corporation, Code of Practice 2011 (revised in 2014)
http://about.abc.net.au/reports-publications/code-of-practice-2014/
FACTS, Digital Terrestrial Television Report of the DTTB Selection Panel, June, 1998
Free TV Australia, Commercial Television Industry Code of Practice – January 2010 (incorporating
amendments to July 2013) www.freetv.com.au/content_common/pg-code-of-practice-.seo
Free TV Australia, "Free TV Today", October 2014, www.freetv.com.au/content_common/pg-free-tv-stats-
and-graphs.seo
Free TV Australia, OP-40 Issue 3 – December 2012 – updated, Allocation of DVB Service Information Codes
for Australia
Free TV Australia, OP 41 Issue 7 – February 2013, LCN Descriptor
ITU-R reports and Recommendations
ITU-R Recommendation BT.500-13 (01/2012), Methodology for the subjective assessment of the quality of
television pictures
Recommendation ITU-R BT.1368-11 (02/2014), Planning criteria, including protection ratios, for digital
terrestrial television services in the VHF/UHF bands
ITU-R Recommendation BT.1735-2 (02/2014), Methods for objective reception quality assessment of
digital terrestrial television broadcasting signals of System B specified in Recommendation ITU-R BT.1306
ITU-R Report BT.2140-7 (04/2014), Transition from analogue to digital terrestrial broadcasting
Technical standards
Standards Australia, Digital television – Terrestrial broadcasting Part 1: Characteristics of digital terrestrial
television transmissions AS4599.1-2007.
Standards Australia, Digital television – Requirements for receivers Part 1: VHF/UHF DVB-T television
AS4933.1.
Standards Australia, Coaxial cable and optical fibre systems for the distribution of analogue and digital
television and sound signals in single and multiple dwelling installations AS/NZS 1367:2000
ETSI TS 136 101 V11.9.0 (2014-08) LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); User
Equipment (UE) radio transmission and reception (3GPP TS 36.101 version 11.9.0 Release 11)
Other references
Dr Rhonda Jolly, Going digital: tracing the transition to digital terrestrial television in Australia, RESEARCH
PAPER NO. 7, 2010-11, 19 November 2010, Parliament of Australia Parliamentary Library
J Given, ‘Taking a punt with TV’, The Sydney Morning Herald, 26 March 1998, p. 19

International Telecommunication Union (ITU)
Telecommunication Development Bureau (BDT)
Office of the Director
Place des Nations
CH-1211 Geneva 20 – Switzerland
Email: bdtdirector@itu.int
Tel.: +41 22 730 5035/5435
Fax: +41 22 730 5484
Deputy to the Director and
Director，Administration and
Operations Coordination
Department (DDR)
Infrastructure Enabling
Environmnent and
e-Applications Department (IEE)
Innovation and Partnership
Department (IP)
Project Support and Knowledge
Management Department (PKM)
Email: bdtdeputydir@itu.int Email: bdtiee@itu.int Email: bdtip@itu.int Email: bdtpkm@itu.int
Tel.: +41 22 730 5784 Tel.: +41 22 730 5421 Tel.: +41 22 730 5900 Tel.: +41 22 730 5447
Fax: +41 22 730 5484 Fax: +41 22 730 5484 Fax: +41 22 730 5484 Fax: +41 22 730 5484
Africa
Ethiopia Cameroon Senegal Zimbabwe
International Telecommunication
Union (ITU)
Regional Office
P.O. Box 60 005
Gambia Rd., Leghar ETC Building
3rd floor
Addis Ababa – Ethiopia
Union internationale des
télécommunications (UIT)
Bureau de zone
Immeuble CAMPOST, 3e étage
Boulevard du 20 mai
Boîte postale 11017
Yaoundé – Cameroon
Union internationale des
télécommunications (UIT)
Bureau de zone
19, Rue Parchappe x Amadou
Assane Ndoye
Immeuble Fayçal, 4e étage
B.P. 50202 Dakar RP
Dakar – Senegal
Union (ITU)
Area Office
TelOne Centre for Learning
Corner Samora Machel and
Hampton Road
P.O. Box BE 792 Belvedere
Harare – Zimbabwe
Email: itu-addis@itu.int Email: itu-yaounde@itu.int Email: itu-dakar@itu.int Email: itu-harare@itu.int
Tel.: +251 11 551 4977 Tel.: + 237 22 22 9292 Tel.: +221 33 849 7720 Tel.: +263 4 77 5939
Tel.: +251 11 551 4855 Tel.: + 237 22 22 9291 Fax: +221 33 822 8013 Tel.: +263 4 77 5941
Tel.: +251 11 551 8328 Fax: + 237 22 22 9297 Fax: +263 4 77 1257
Fax: +251 11 551 7299
Americas
Brazil Barbados Chile Honduras
União Internacional de
Telecomunicações (UIT)
Regional Office
SAUS Quadra 06, Bloco “E”
11º andar, Ala Sul
Ed. Luis Eduardo Magalhães (Anatel)
70070-940 Brasilia, DF – Brazil
Union (ITU)
Area Office
United Nations House
Marine Gardens
Hastings, Christ Church
P.O. Box 1047
Bridgetown – Barbados
Unión Internacional de
Telecomunicaciones (UIT)
Oficina de Representación de Área
Merced 753, Piso 4
Casilla 50484, Plaza de Armas
Santiago de Chile – Chile
Unión Internacional de
Telecomunicaciones (UIT)
Oficina de Representación de Área
Colonia Palmira, Avenida Brasil
Ed. COMTELCA/UIT, 4.º piso
P.O. Box 976
Tegucigalpa – Honduras
Email: itubrasilia@itu.int Email: itubridgetown@itu.int Email: itusantiago@itu.int Email: itutegucigalpa@itu.int
Tel.: +55 61 2312 2730-1 Tel.: +1 246 431 0343/4 Tel.: +56 2 632 6134/6147 Tel.: +504 22 201 074
Tel.: +55 61 2312 2733-5 Fax: +1 246 437 7403 Fax: +56 2 632 6154 Fax: +504 22 201 075
Fax: +55 61 2312 2738
Arab States Asia and the Pacific CIS countries
Egypt Thailand Indonesia Russian Federation
Union (ITU)
Regional Office
Smart Village, Building B 147, 3rd floor
Km 28 Cairo – Alexandria Desert Road
Giza Governorate
Cairo – Egypt
Union (ITU)
Regional Office
Thailand Post Training Center, 5th
floor,
111 Chaengwattana Road, Laksi
Bangkok 10210 – Thailand
Mailing address
P.O. Box 178, Laksi Post Office
Laksi, Bangkok 10210 – Thailand
Union (ITU)
Area Office
Sapta Pesona Building, 13th floor
JI. Merdan Merdeka Barat No. 17
Jakarta 10001 – Indonesia
Mailing address:
c/o UNDP – P.O. Box 2338
Jakarta 10001 – Indonesia
Union (ITU)
Area Office
4, Building 1
Sergiy Radonezhsky Str.
Moscow 105120
Russian Federation
Mailing address:
P.O. Box 25 – Moscow 105120
Russian Federation
Email: itucairo@itu.int Email: itubangkok@itu.int Email: itujakarta@itu.int Email: itumoskow@itu.int
Tel.: +202 3537 1777 Tel.: +66 2 575 0055 Tel.: +62 21 381 3572 Tel.: +7 495 926 6070
Fax: +202 3537 1888 Fax: +66 2 575 3507 Tel.: +62 21 380 2322 Fax: +7 495 926 6073
Tel.: +62 21 380 2324
Fax: +62 21 389 05521
Europe
Switzerland
Union (ITU)
Telecommunication Development
Bureau (BDT)
Europe Unit (EUR)
Place des Nations
CH-1211 Geneva 20 – Switzerland
Switzerland
Email: eurregion@itu.int
Tel.: +41 22 730 5111

DTTB_Case_Study_Australia_2015

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to DTTB_Case_Study_Australia_2015 (20)

DTTB_Case_Study_Australia_2015